INSTALLATION INSTRUCTIONS

EVOLVEVERTICAL / HORIZONTAL

WALL BED HARDWARE

Architectural Products by Outwater, LLC.24 River Road, P.O. Box 387, Bogota, NJ 07603-0387Phone: 1-800-835-4400 • Fax: 1-800-835-4403

www.outwater.com

Architectural Products by Outwater LLC | 1-800-835-4400 | outwater.com

N x1

O x1

P x2

Q x2

R x1

S x4

T x2

U x20

V x12

W x8

X x3

Y x8

Z x4

AA x2

1

HARDWARE

A x16

B x16

C x8

D x4

E x2

F x6

G x2

H x2

I x2

J x2

K x2

L x8

M x8

Threaded Insert

M8 x 16 Screw

M5 x 55 Screw

Nylon Washer

M8 x 40 Bolt

M8 Nut

Piston

Mattress Support

M5 x 10 Screw

Fastener

Bracket

Washer

M6 x 20 Screw

Wrench

Allen Key

Plate

Leg

Tube

M5 Nut

Flat Bar

5/8in x 15mm Screw

Door Bracket

1 3/4in x 44mm Bolt

2 3/4in x 70mm Bolt

Slat Cap

Slat

M5 x 30 Bolt

Architetural Products by Outwater LLC o�ers a 5 year limited warranty on slat bases used in the wall bed as well as the mechanisms. The warranty covers the replacement of parts with manufacturing defects and/or breakage caused by regular use. It does not cover damages caused by a poor installation or misuse of the product. Professional installation suggested. The bed must be secured to the wall into wood or metal studs.

2

290

155.50

196.50

64

64

28.50

83.50

290

354

450

244.50

179.50

DRILLING GUIDE

FrontBack

Bottom

All measurements are for 19mm (3/4’’) board.

3

Right side

Front

Front

Left side

Bottom

INSTALLING THE MOUNTING BRACKETS1

A + B

A

P

B

P

Wood

ASSEMBLING THE CABINET2

* See conversion guide for suggested cabinet dimensions.

4

ASSEMBLING THE FRAME4

3 SECURING TO THE WALL

* Professional installation recommended.

* Needs to be secured into at least two wood or metal studs.

L + M K

4.1-

Attach the two half frames with X

4.2-

T to the frame with W

T

W

x3X

x8

T x2

5

5

6

MOUNTING THE FRAME ONTO THE MOUNTING BRACKET

IJS

x2

x2

x2

ATTACHING THE PISTONS TO THE FRAME

F= x2

Secure the shorter ends of the pistons to the frame

G= x2

6

Tilt the frame past the cabinet edge to mount the pistons on the mounting brackets through the opening between the slats

7 INSTALLING THE PISTONS TO THE CABINET

F x2

8 INSTALLING THE STOPPER

Install the stopper (not included) on the inside top of the cabinet where it will allow

cabinet.

7

9 INSTALLING THE LEGS

F

D

E

R

Q

x2

x4

Install legs to bed frame.

Do not overtighten.

Install tube to both legs.

Q

6.1

6.2

EAA

S

x2

x2

x2

10 INSTALLING THE DOOR BRACKETS

V x12

Install the door brackets in alignment with the support bars on the bed frame.

The door brackets must point downward

AA

8

11 INSTALLING THE DOORS

Hook the door brackets onto the frame and push down until they click.

Attach the doors to the frame while putting weight on the frame to keep the bed open.

CU

CU x 20

x 8

11.1

11.2

9

INSTALLING THE MATTRESS SUPPORT

Insert the mattress supports into the predrilled holes in the bed frame.

H

12

13

H x 2

INSTALLING THE SLATS

Place a cap on both ends of the slats. Insert the slats into their designated holes along the frame.

YZ

x8

x4

Y

Z

10

14 USING THE WALL BED

.

The wall bed is assembled and shown in lowered position.

Pivot the leg towards the inside of the unit.Make sure leg is fully closed.

Pull up gently to close. Leg serves as mattress retaining system. Pistons insure that door closes properly and remains closed.

.