ew

ack

er@

spe

ed

bie

r.d

e

Draft Beer for Large Events

The Lucrative Alternative to Conventional Draft Beer

Equipment

Serve more people in less time. Success will not stay away

TDS Schanktechnik UG presents a new technology which enables caterers and brewers to pour and sell draft beer faster and more profitably

• Completely Maintenance-Free• Easy to handle• Easy to clean• Practically unbreakable• Retro fittable to existing systems• Installation Time max. 5 Minutes• No Power required• Experience from Stadia and Events: Up to 100 % more beer sales

ew

ack

er@

spe

ed

bie

r.d

e

Five Steps to Faster, More Profitable Beer Sales

1 Original Situation 2 Remove Existing Valve

3 Screw in Adapter

4 Mount Pouring Device, Counter MountHolder and Drip Cup

5 You are now ready to pour Beer faster and more profitably

ew

ack

er@

spe

ed

bie

r.d

e

Cooling Technology

As June/July 2010 have made quite clear to everybody, summers are getting hotter, which leads to problems mainly at events where available cooling equipment cannot cope with „tropical“ temperatures while beer kegs get warm increasingly faster. Additionally there is extra load on the electrical supply system due to longer run times of air-conditioners, coolers, fans etc.

With extreme temperatures parts of the draft beer system also have to be more extreme. This goes mainly for

• Pressure Regulators• Coil Packages• Cooling System

ew

ack

er@

spe

ed

bie

r.d

e

• All in all the following can be obtained by employing fast pour technology in conjunction with adequate cooling (Alternative Solutions see below):

• More turnover through faster pour• More cups/glasses per keg through better keg yield• More profit through higher turnover at constant cost• Minimisation of the number of remaining used kegs• Enabling fast pour of beer everywhere, including sites without electricity or mobile

sites

• This with utmost possible technical simplicity, i.e. if possible without electricity and electronics.

The following pages list various suggestions for different applications.

ew

ack

er@

spe

ed

bie

r.d

e

1 2 3

Kegs can be hooked up in series

InsulatedCO2

Typical Application 1

Cold Plate with pouring device,

completely independent from power supply.

Preconditions:

Ice Cubes

(At extreme temperatures approx. 1 Kg Ice for 4 L beer. With pre-chilled kegs approx. 1 Kg Ice for 10 L beer)

ew

ack

er@

spe

ed

bie

r.d

e

Ice Cubes

Cold Plates

Insulated Bin

1 2 3

Kegs can be hooked up in series

Insulated

CO2 (Regulator High volume)

Typical Application 2Cold Plates with two pouring devices

Completely independent from power supply

Only one series of kegs hooked up will supply two valves

Preconditions:

Ice Cubes

CO2 regulator high volume

ew

ack

er@

spe

ed

bie

r.d

e

Ice Cubes

Cold Plates

Insulated Bin

CO2

Typical Application mobile, no power supply needed.

Cold Plate with pouring device for mobile use in stadia or other events

Mobile but still uses standard kegs and CO2 Cylinders

Preconditions:

Ice Cubes

(At extreme temperatures approx. 1 Kg Ice for 4 L beer. With pre-chilled kegs approx. 1 Kg Ice for 10 L beer)

ew

ack

er@

spe

ed

bie

r.d

e

Keg

Cold Plate

Ice

Insulated Tub

• Ice Requirement:

• with a Delta T 20 degrees approx. 1 Kg Ice for approx. 4 L Beer (Kegtemperature 25°C) = 25 Kg Ice per 1 hL beer

• with a Delta T 8 degrees approx. 1 Kg Ice for approx. 10 L Beer (Kegtemperature ca. 10 – 12 °C) = 10 Kg Eis per 1 hL beer

•With a Delta T 4 degrees approx. 1 Kg Ice for approx. 20 L Beer (Kegtemperature < 8 °C)= 5 Kg Eis per 1 hL beer

• Application:Events of any kind, creation of new sales points without electricity.

• Mobile KiosksSports Stadia, Kiosks and Events in the Infield

ew

ack

er@

spe

ed

bie

r.d

e

1 2 3

Kegs can be hooked up in series

CO2-Pressure Regulator

Fob Stop

Power Cooler

Beer Inlet into cooler

Typical Application 3Power Cooler and one Pouring Device mounted on top of cooler or remote

Cooler needs to be filled with water and builds Ice Bank.

ew

ack

er@

spe

ed

bie

r.d

e

PreconditionsElectricityWater

1 2 3

Kegs can be hooked up in series.

Beer line is split inside cooler and supplies two pouring devices. This ensures small number of remaining used kegs

CO2-Pressure Regulator, High Volume

Fob Stop

ew

ack

er@

spe

ed

bie

r.d

e

Beer Inlet

Typical Application 4Power Cooler and two Pouring Devices

Quasi ready for use

Cooler needs to be filled with water and builds Ice Bank

Preconditions:ElectricityWaterPressure Regulator High Volume

Power Cooler

1 2 3

Kegs can be hooked up in Series

Insulated or better even with ancilliary cooling

CO2

Typical Application 5

Remote Flash Cooler and Pouring Device.

Typical application where device is mounted onto already existing draft beer systems.

Preconditions:

Electricity

Water

Pre-chilled Kegs

ew

ack

er@

spe

ed

bie

r.d

e

1 2 3

Insulated or better even with ancilliary cooling

Kegs can be hooked up in series.Beer line is split inside cooler and supplies two pouring devices. This ensures small number of remaining used kegs

Typical Application 6

Flash Cooler and two Pouring Devices

Preconditions:ElectricityWaterPre-chilled KegsPressure Regulator High Volume

ew

ack

er@

spe

ed

bie

r.d

e

Existing Dispense Head Pouring Device is mounted instead of the existing valve

CO2 Pressure Regulator High Volume

Video Clips are available on YouTube or on CD.

Ask for URLs or CDs at:

TDS Schanktechnik UG Ekhard WackerDrosselweg 537520 OsterodeGermany

Tel.: +49 05522 5057172Mobile: +49 0171 6405052

ewacker@speedbier.de