Upload
stuartlennie6478
View
231
Download
0
Embed Size (px)
Citation preview
8/9/2019 Ex1 Microwave
1/21
Exercise One
The Microwave
8/9/2019 Ex1 Microwave
2/21
Get to Know your Mouse
Left mouse button
Used for most operations such as selecting
icons, menus and graphic entities.
Right mouse button
Brings up additional options
Select in thetutorial means
using the
left mouse
button.
The Esc
key on your
keyboard is
used to
cancel a
command.
When Inventor startsyou will see this
Start-up dialogue box.Select the Metric tab
.
Then select the
Standard(mm).pt
icon
8/9/2019 Ex1 Microwave
3/21
Screen Layout
Sketch paneltoolbar
3D Indicator
Message / Status bar
Graphics window
Take a few
minutes to lookat this screen
StandardToolbar
Pull
Down
Menus
Select the line icon from the 2D Sketch Panel
(Note all points at this stage are approximate)
Select Point 1 a point to start the line move the mouse and
select Point 2. Ensure the line is straight, look out for the
horizontal constraint symbol.
Point 1
Point 2
Horizontal Constraint symbol
8/9/2019 Ex1 Microwave
4/21
When we move the mouse and select point 3 we should notice
the perpendicular constraint symbol.
Point 3
Perpendicular constraint symbol
Select point 4 by moving the mouse horizontally. Notice theParallel constraint symbol, this means the new line is parallel to
the first one.
Point 4
Parallel constraint symbol
8/9/2019 Ex1 Microwave
5/21
Select point 5 look out for the parallel symbol to indicate that this vertical line is
parallel to the line drawn between points 3 and 4.
Point 5Point 6
As you select point 6 notice the parallel constraint symbol. Look out
for the hidden line this tells us that point 6 is aligned with point 1.
Select point one again to finish the Closed shape.
To end drawing lines press Esc key.
Starting point
Hidden linemeans alignment
between point 1
and point 6.
parallel constraint symbol
From the 2D Sketch menu select the General Dimension icon.Select the line to dimension.
Move the MOUSE upwards notice the dimension and line
follows the mouse pointer.
Select a position similar to the position shown.
A Edit dimension box will appear. The dimension will be
shown highlighted press the delete key.
Type 90 you dont have to add mm after the dimension.
Select the green tick to OK it and update the dimension.
8/9/2019 Ex1 Microwave
6/21
On your own, dimension the shape as shown. Edit the
dimensions to the sizes shown.
Right click anywhere on the screen and select Done or press
the Esc. key on the keyboard to finish dimensioning.
Right click the anywhere again on the screen and select Finish
Sketch.
Important try to remember this sequence to allow you to
Finish Sketching.
8/9/2019 Ex1 Microwave
7/21
Right click anywhere on the screen and select the
Isometric View.
Isometric View sometimes
called the safe view because
you can always return to it.
Finishing the 2D Sketch allows us access to the Part Features menu.
1. Select
Extrude from
the Part
Features
toolbar.
2. In the
Extrude Pop
up window
enter 50 asthe extrusion
Depth.
3. Notice that the sketch region is
automatically selected as the
extrusion profile.
Select OK to finish
the command.
8/9/2019 Ex1 Microwave
8/21
Your Shape should look like
this I hope ?
Select the Look At icon and select the face as shown.
Look out for
this symbol
at the arrow
head
8/9/2019 Ex1 Microwave
9/21
Select the
2D Sketch
icon and
select the
shape asshown.
The new sketch plane
should appear as
shown.
From the 2D Sketch Panel select the two point rectangle.
Select the first point as
shown
Select the second point as shown
8/9/2019 Ex1 Microwave
10/21
On your own dimension
the rectangle as shown.
Press the Esc. key to finish the
dimensioning and right click and
select Finish Sketch.
From the Part Features menu
select Extrude.
Select the Profile Button movethe mouse pointer and select
inside the rectangle we have
just drawn. Make sure it turns
blue.
Set the Distance to 1.
Select OK.
Right click anywhere on the screen and
select Isometric view.
Select the edges as shown in order to
dimension over two feature
Hope your shape looks
like this ?
8/9/2019 Ex1 Microwave
11/21
Select the Look At icon and select
this face
Select 2D Sketch and select thisface. For to start a new sketch.
On your own
using the 2
Point
rectangle.Draw and
dimension
two
rectangles as
shown.
2.5
8/9/2019 Ex1 Microwave
12/21
Esc dimensioning and Finish
sketching.
From the Part Features menu
select Extrude.
Set the Depth to .5 and
select OK.
Select the
Profile button.
Select both
rectangular
shapes.
Select the look at icon and
select this face
Select 2D Sketch icon and select
the same face .
Adding control dials to your Microwave
.
Select Centre point
circle from 2D Sketch
Panel and Select a
suitable position. Drag
the circle to an approx
size. Dimension circlesposition and diameter
of 5mm.
8/9/2019 Ex1 Microwave
13/21
Esc to finish
dimensioning and Right
click selecting Finish
Sketch
Right click and selectthe Isometric View.
Select Extrude from
Part Features menu.
Select the circle as the
profile and set the
distance to 2mm.
Select OK to finish.
Select Wireframe Display to view the microwave. You may
require to select the down arrow to display this
Select Rectangular Pattern for our Array.
1. Select the Feature. Select the cylinder.
2. Select Direction 1: Select the edge of the plate. Notice
a green arrow appears pointing the direction. The arrow
must point as shown. Select the Flip button if you need
to change direction.
3. Alter count to 2
4. Alter Length to 10
Feature
Count
Length
Do not select OK or your dials will only be in one direction.
Direction 1
Flip
8/9/2019 Ex1 Microwave
14/21
1. Select Direction 2.
(Edge of Microwave)
2. AlterCount to 2.
3. AlterLength to 10
4. Now select OK.
Select
Shaded
Display to
view our
Dials.
You may
have to
select Flip
to get the
correct
direction.
Select Rotate icon next to the Look At icon
Select the
Handles notice
how your
model moves
about.
Do not worry
too much as
you can
always reset to
the Isometric
View.
Handles
8/9/2019 Ex1 Microwave
15/21
Try to Rotate your Model into this position
Select
Wireframe
Display
Right click
anywhere
on thescreen and
select
Done from
the menu.
To finish
Rotate.
Select Fillet from the Part Features Menu.
Select the edges as shown noticethat the microwave is in
Wireframe View this will help
you select the edges.
Select below
Radius and type in
1 for the radius
Ensure you select the
pencil.
Select OK to Finish the command
8/9/2019 Ex1 Microwave
16/21
Hopefully it looks like this ?
Select Chamferfrom the Part Features menu.
Select Edges.
Select Distance to .5
Make sure
this button is
pressed
Select the Dials as shown
Select OK to Finish the Command
8/9/2019 Ex1 Microwave
17/21
Hope your Microwave looks
like this ?
Select Isometric View Select Shaded Display
Inventor has a special user interface called DynamicViewing that enable convenient viewing of the entities in the
graphic window.
Select the Zoom icon.
Select inside the graphics window.
Press and hold down the left-mouse button, then
move downward to enlarge the view ormove
upwards to decrease the view.Press the Esc key once to exit the Zoom command.
Select the Pan icon located next to the Zoom command.
The Pan command allows us to move the view to a different
position.
Try both the commands out and remember to use them in the
future.
8/9/2019 Ex1 Microwave
18/21
Your model will be shaded with a material called As Material to give the
microwave a more realistic look select the door it should be highlighted.
You can add other faces such as the edges of the door by holding
down the Ctrl key and selecting all the faces of the door .Use the
Rotate to get them all.
Lets add some Textures
Right click and
select Propertiesfrom the menu
From the Face
Properties menu
select the down arrow.
Select Black as
the Face ColourStyle.
Select OK to finish
the command.
8/9/2019 Ex1 Microwave
19/21
Lets add some detail to one of the two
plates we constructed earlier.
On your own create
a new 2D Sketch on
surface of the plate .
Draw a Two Point
Rectangle.
Dimension the
rectangle as shown.Use the Zoom &
Pan icon to get the
view as shown. Esc
dimensioning and
Finish Sketch.
Select Isometric View.
On your own Extrude the
plate not outwards but
inwards to create a
recessed surface. Make
sure you choose Cut and
not Join.
the Distance should be
0.5.
8/9/2019 Ex1 Microwave
20/21
Select the Look At icon and select the recessed surface.
Lets add a Text message such as FULL POWER.
Select a new 2D Sketch on the recessed surface.
Select the TextIcon from the 2D
Sketch Panel
Select a suitable
point on the
recessed surface
to start the text.
Zoom In
In the dialogue box
type FULL POWER
Select OK.
If its not in the right place then
select it and move it.
Alter Height to 1.00
8/9/2019 Ex1 Microwave
21/21
On your own change the faces of the
microwave to suitable materials.
I have chosen Green Pastel for the casing.
Chrome for the dials.
Black for the glass surfaces.
Remember to Rotate your Microwave to get all
the surfaces.
Red for the text