Examen CCNP

7/28/2019 Examen CCNP

1/4

Estoy cursando CCNP 3.1 y busco las pruebas,, esta la saque cuando di el examendel modulo!!!

Cisco Systems

Close Window

Assessment System

1. Assessment Selection

2. Assessment Settings

3. Take Assessment

Take Assessment - Module 3 Exam - CCNP 1 Advanced Routing (Version 3.1)

Time Remaining:

1

In the graphic, RTA and RTC are configured with RIP. RTA has a primary route to10.0.0.0/8 through RTC. Which configuration should be applied to RTA to create afloating static route that can be used as a backup route to 10.0.0.0/8 after th

e RIP route fails?RTA(config)#ip route 10.0.0.0 255.0.0.0 1.1.1.1RTA(config)#ip route 10.0.0.0 255.0.0.0 1.1.1.1 90RTA(config)#ip route 10.0.0.0 255.0.0.0 1.1.1.1 120RTA(config)#ip route 10.0.0.0 255.0.0.0 1.1.1.1 130

2When a router receives updates from different routing protocols regarding the same network, what is the determining factor for choosing the best route?hop countrouting metrictopological databaseadministrative distance

3Examine the output of the show running-config command.

interface serial 0ip address 172.16.1.1 255.255.255.0!interface ethernet 0ip address 10.1.1.1 255.255.255.0!


2/4

router ripversion 2network 10.0.0.0!ip route 0.0.0.0 0.0.0.0 serial0

Which statement about RIP updates is true for this configuration?RIPv2 updates are sent and received on interface S0 of the router.A default route is sent to neighbors on interface S0 of the router.A default route is sent to neighbors on interface E0 of the router.RIPv2 updates are sent and received on interfaces E0 and S0 of the router.

4Which administrative distance value is assigned to a floating static route?one that is less than the primary routeone that is greater than the primary routeone that is equal to the primary routea value of zero

5How do balanced hybrid routing protocols conserve bandwidth?by using LSAs to pass the topology databaseby periodically broadcasting routing tables to connected routers

they are event driven rather than periodicbalanced hybrids do not need to conserve bandwidth

6Which command should be used to define a static route that will remain in the routing table even if the interface shuts down?ip route 10.6.0.0 255.255.0.0 S0/1ip route 10.6.0.0 255.0.0.0 192.168.2.1 200ip route 10.6.0.0 255.255.255.0 S0/1 permip route 10.6.0.1 255.255.255.255 S0/1 tag

7Which two characteristics are typically displayed by routers that are configured

to use a distance vector routing protocol? (Choose two.)identify their neighbors for direct communicationsend their complete routing tables at regular intervals to neighbor routersafter initialization, send partial routing table updatesbroadcast their routing tables on all configured interfacesare concerned with only distance

8Which command is used to propagate a default route in an IGRP network?ip route 0.0.0.0 0.0.0.0 ip addressdefault-information originatenetwork 0.0.0.0ip default-network ip address

9

In the diagram, RIP is running between RTR_SVS and RTR_IT only. Which command would configure RTR_SVS to set up a default route to the Internet?ip route 0.0.0.0 0.0.0.0 172.16.23.1default-information originateip route 0.0.0.0 0.0.0.0 199.168.5.2ip default-network 0.0.0.0


3/4

10Select two parameters that are always included in the configuration of static routes. (Choose two.)destination prefixdestination masklocal interface of peer routerfloating static routesadministrative distance

11

Observe the above output taken from a portion of the show ip route command. An IP packet with a destination IP address of 192.168.32.1 arrives on an interface.Given the above information, which IP address would the router select to forwardthe packet to its destination?10.1.1.110.1.1.210.1.1.310.1.1.4

12Which two statements describe link-state routing protocols? (Choose two.)

based on the Bellman-Ford algorithmuse less router CPU and memory than distance vector protocolssupport variable length subnet masking (VLSM)broadcast the entire routing table on all configured interfacessend partial updates when a topological change occurs

13

In the diagram, RIP is the routing protocol between RTR_SVS and RTR_IT. What happens when the command ip default-network 10.16.23.0 is entered on RTR_SVS?0.0.0.0 route is dynamically sent to all RIP neighbors.10.0.0.0 route is dynamically sent to all RIP neighbors.

10.16.23.0 route is dynamically sent to all RIP neighbors.This command is not compatible with the RIP routing protocol.

14Given the following partial configuration, which static route would be the primary default path?

router ripnetwork 10.10.10.0

ip route 0.0.0.0 0.0.0.0 172.16.20.2 40ip route 0.0.0.0 0.0.0.0 192.68.6.1 50ip route 0.0.0.0 0.0.0.0 202.16.20.2 60

ip route 0.0.0.0 0.0.0.0 212.68.6.1 70ip route 0.0.0.0 0.0.0.0 172.16.20.2 40ip route 0.0.0.0 0.0.0.0 192.68.6.1 50ip route 0.0.0.0 0.0.0.0 202.16.20.2 60ip route 0.0.0.0 0.0.0.0 212.68.6.1 70

15Which two factors are used by IGRP by default to calculate the metric? (Choose two.)MTU


4/4

bandwidthloaddelayreliability

Showing 1 of 2 Close Window

All content copyright 1992-2005 Cisco Systems, Inc. Privacy Statement and Trademarks.

Documents

Examen CCNP