USER GUIDE

Model F-808

Combined Galvanic & Ultrasonic Peeling Unit Version II

USER MANUAL F-808 Combined Galvanic & Ultrasonic Peeling

Machine Functions: 1. By means of ultrasonic waves, the machine exfoliates the outer dermal layer for deep Cleansing

and is particularly useful for the treatment of Acne, comedones, Milia, and the removal of dead Cells, dirt and everyday pollution of skin.

2. By means of galvanic (direct) current the machine is used for the deep penetration of polarised

Active substances into the outer dermal layers, having numerous beneficial effects on the skin Such as helping remove/plump wrinkles, alleviating dark spots and general brightening of the Complexion.

Power supply: 1. Ensure the mains supply voltage matches that of your model of machine before plugging in.

Insert the power lead into the rear of the machine (as indicated on rear panel) before connecting To the mains supply. Next, switch on the supply at the mains. Never plug in electrical devices With wet or moist hands.

2. Connect the remaining machine attachments properly in accordance with machine use. Method of functions:

Ultrasonic Peeling Use 1. Press “P2” button to select the ‘cleaning program’.

2. Place the indifferent wristband securely around the clients wrist.

3. Adjust the “ENERGY” output to the desired level.

4. Apply the appropriate cleansing product generously to the surface of the skin.

5. The ultrasonic peeling is shown in the method diagrams, A, B, & C below with its benefits.

A. Painless Acne Cleansing The ultrasonic frequency wave used, atomises The acne in the pores quickly, and disperses The Debris up to the skins surface without any client discomfort.

B. Deep Pore Cleansing The frequency of the Ultrasonic waves forces The remains of any cosmetics or oil to the Outer dermal layer and disposes of them During the cleansing process, quickly helping To return the skin to its natural state of Balance.

C. Follicle Cleansing

The flat spade-like probe is a safer way to Clear debris in follicles and helps to prevent The Signs of aging. The distinctive effect of The Ultrasonic waves gives an instant and Visible Difference in the appearance of the Skin.

Galvanic Function (1). The anti-bacterial and deodorizing effect, given by the special probe’s micro-electrical current

On to the skins surface, helps with the cellular renewal of the skin. (2). Working on a cellular level, the metabolic process is increased and aids the skin surface to be

Smoother, and with regular treatment help slow the progression of fine lines and wrinkles, Bringing a tightened effect to the skins appearance.

(3). This-stimulation of cells inside the tissue layers, results in both revitalization of the blood, and of

The Lymph system, which can help to alleviate dullness and dark patches. (4). Helping to ‘deep’ moisturise the skin and regain its elasticity and glow.

Galvanic Use: (a) Press the “P1” key, to choose the galvanic only function (the LED will light up to confirm current

output, as shown below).

(b) Then choose the polarity of the required current by pressing the “LEAD” button, to switch

Between either the “+” or the “-“ outputs. (‘+’ being the ( I ) LED being lit, or for ‘-’ the ( o ) LED being lit.)

(c) The use of an indifferent wristband is now replaced by using the two earth pins on the hanset. Once you place your fingers (thumb & index) on each of the earth pins, the safety circuit will be made and the galvanic current will flow to the probe. If you release your grip, the current will cease after 3-5 seconds for safety purposes. (d) Using the ‘intensity’ buttons (up or down),

You may then decrease or increase the intensity until the client can feel a mild tingling sensation. The output current control, ranges from approximately 0.05ma to 0.35ma maximum, with

incremental increases of approx 0.03ma per illuminated LED. The timer is preset at a start value Of “15” minutes, and may be adjusted more-or less, as required.

5. Generously apply the chosen/correctly polarised product over the area of skin to be treated.

6. Use the probe as shown below in the diagrams D & E.

D. Cleansing

The probe now uses the galvanic current to Decompose melanin & debris and sends them To the skins surface to be cleansed away, Giving a brighter appearance to the skin.

&

E. Smoothing The vibration (frequency) of the ultrasonic Waves, helps to increases the skin’s metabolic Rate and penetrates deeply in to the dermal Tissue giving a warming action which can help To loosen and smooth wrinkles.

Combined Galvanic & Ultrasonic Use 1. Press the “P1” and “P2” keys on (LED’s will illuminate to show active) for combined phases.

+ 2. Place the indifferent wristband securely around the client wrist. 3. Adjust both the“INTENSITY” and “ENERGY” to the desired levels of output.

&

4. Apply the chosen conductive product evenly over the part of the skin being treated.

5. Use the probe in accordance with the methods shown in both the ‘Peeling’ and ‘Galvanic’ Stages listed above.

Operational Guidance:

1. The probe will not vibrate when used on ‘P1’ program as this is a galvanic only program. 2. The ‘galvanic’ program phase works with a ‘positive earth’ control system. This means that

‘unless the machine can find an earth return via the indifferent wristband, the system will stop the Current output to the probe. However, when the probe is again in contact with the client, the System will restart the current output immediately. This is a safety feature and should not be Confused with a system fault.

3. When the machine is operated in the ‘ultrasonic peeling’ program the phase, it works with a

‘positive earth’ control system (as per the galvanic phase). This means that ‘unless the machine Can find an earth return via the indifferent wristband, the system will stop the current output to The Probe (vibration will stop). However, when the probe is again in contact with the client and The Earth circuit is found, the system will restart the output immediately. This is a safety feature And should not be confused with a system fault.

4. When the machine is used in both P1 & P2 combined phases, both of the above (2 & 3) sections Will apply, and both safety systems will work simultaneously. This means that if contact is broken (earth circuit can’t be found) both outputs will cease until the probe is again in contact with the Client and the earth circuit is re-established. This is a safety feature and should not be confused With a system fault.

General Contraindications:

• Pacemaker (or any rhythmic heart stabilising device) • Pregnancy • Thrombosis or Phlebitis • Skin diseases of any type • Operations (invasive) within the last 6 month period • Silicone or metal implants • Hypersensitive or Vascular skins

General Machine Practices: 1. Do not use the probe in one position on the skin for too long, to avoiding the risk of

Galvanic burning. 2. Do not use on dry skin. Always ensure a generous amount of conductive product is used

To maintain a good earth circuit, and to prevent any overheating of the skins surface. 3. Always insert & remove the probe cable by holding the socket. Do not push or pull the

Probe lead by the wire, to prevent damage to the inner core. 4. Always insert or remove the power lead only by the socket/pin piece. Do not push or pull

by the Cable, to prevent damage to the inner core. 5. Do not coil the probe cable tightly. When storing the probe, loosely coil the cable in large

Loops to prevent damage to the cable core.

6. Always handle the probe with care as it contains delicate components. Failure to handle With care (dropping etc) will result in damage to the internal ultrasonic generators.

7. Take particular care of the probe ‘blade’ as any damage will cause scratching of the Skins surface during use. Always store the probe safely when not in use.

8. Always ensure the mains supply voltage is correctly matched to the machine prior to

plugging into the mains supply. 9. The machine has no user changeable components and under no circumstances should

it be opened by an unauthorised person. Should a fault occur- please contact your machine supplier or a competent /qualified electrical technician immediately.

10. During the machine warranty period, all repairs must (unless otherwise approved) be

Done by returning the machine to your supplier. This also applies to attachments, which Will need inspection prior to any replacement being issued. Never use any other type of Attachments with your machine, other than original parts purchased/supplied by your Official supplier.

11. Never use the machine with wet or moist hands, to prevent any accidental earthing or

Possible electric shock. Machine positioning: 1. Always use the machine on a hard flat surface. (trolleys are recommended where

possible). 2. Never use the machine where the power cord or attachments may be tripped over. 3. Never store the machine near a water supply (especially in plugged in). 4. Never use the machine in the vicinity of a gas supply (to prevent any accidental ignition). 5. Never use the machine from a ‘multi-way socket’ unless fused and CE approved. Routine Maintenance:

1. Always clean the probe ‘blade’ prior any prolonged period of storage. 2. Always sterilise the probe/blade after each use, using a suitable chemical sterilising

Product. 3. Cleaning of the machine should be done using clean warm water with a mild soap

Detergent only. Care should be taken to use a damp cloth with any excess liquid Removed before attempting to clean. A mild sterilising solution may be used for Cleaning, only if you first ‘patch’ test the product on the underside of the unit, to check For any adverse Product reaction.

4. Where possible position the machine out of direct sunlight, to prevent any possible UV

Discolouration of the machine casing.

Warranty Procedure

1 - The warranty on all Cosmetronic equipment is 12 months from the date of invoice and covers the products against defects in materials and workmanship or component defect. Should an item be replaced under warranty the original date of invoice is pertinent to the length of warranty period for any replacement items, e.g. should an item be replaced at month 10 of ownership, the replacement product with inherit the final 2 months of warranty from the originally purchased item invoice date. (Unless superseded by an extended warranty agreement) this warranty is non transferable and applies to the original purchaser only. 2 - No product repairs or component replacement will take place unless all/any amounts owed to Cosmetronic for the said goods have been paid for in full, prior to any repairs. 3 - All extended warranty policies must be paid in full prior to dispatch of goods and will extend the above cover (No 1) by a further 2 or 4 years, to a maximum of 5 years including the first free year.

4 - Before returning any product to Cosmetronic UK Ltd for repair or replacement you must first: - - Endeavour to establish cause of product fault (e.g. check fuses etc.). - Notify Cosmetronic of any fault development within 24 hrs of its occurrence. - Contact a member of our technical service dept (95% of faults can be rectified over the telephone). - Obtain an RMA (return material authorisation) from a member of Cosmetronic. - Package the goods to include all parts or accessories received with that item. - Any item received incomplete for repair will be made complete and all relevant parts charges added to repair. - Package the goods to be returned, in sufficient packaging to prevent any damage occurring in transit. As Cosmetronic or its nominated couriers will not be held liable for damage to products due to insufficient packaging. - Clearly address the returned goods with our full postal address and RMA code.

5 - All goods returned to Cosmetronic without the correct RMA authorisation will be refused.

6 - No goods will automatically be replaced, when a faulty item can be repaired within a reasonable time span (except items deemed unserviceable on arrival). Goods will be replaced at the discretion of Cosmetronic when it is deemed that all/any goods are beyond economic repair. Items of loan equipment may be given at the discretion of the management and subject to delivery/collection charges, together with a refundable deposit.

7 - Cosmetronic will not be held liable for any momentary lack of stock or technical resource, or any other circumstance beyond its control that may delay any component replacement or repair. Cosmetronic will not be held liable for any special, incidental, consequential damages resulting from a breach of warranty, or under any other legal theory, including but not limited to loss of profit or good will, downtime, damage to or any products, treatments used in conjunction with its products. Purchases are deemed at your discretion and as such, your acceptance of Cosmetronic terms & conditions are given at the time of purchase.

8 - When our service department or its appointed agents can find no discernable fault or malfunction with goods returned, you will be liable for any administration and testing or sanitization costs prior to return dispatch. 8a- When goods returned are of a non-merchantable (dirty or unhygienic) condition, they will be made to a ‘merchantable’ or ‘saleable’ quality again, and any cleaning/sanitization or parts costs will be charged as necessary.

9 - All goods returned will be at the owner’s risk. Cosmetronic will not be held liable for any damage or loss, or consequential loss whatsoever of goods whilst in transit to or from Cosmetronic, at your behest.

10 - Carriage costs are at the owner’s expense for both collection & return freight costs for all items returned for repair, either in or out of warranty. All goods collected by Cosmetronic at the owners request, will be carried via Cosmetronic nominated couriers unless specified. Any additional goods in transit insurance required by the owner must be requested prior to collection or dispatch and paid for in full before any collection or dispatch is arranged. Items returned or transported by owners using 3rd party means, are solely at their discretion and no liability will be accepted by Cosmetronic for any claims arising for circumstances outside the control of Cosmetronic UK Ltd.

11 - Repaired goods will not be released until any costs relevant to that repair (unless under warranty) have been settled in full. This will include all carriage & freight costs incurred to the relevant repair.

12 - Call out/on-site repairs will be carried out as soon as is physically possible and charged at a cost of £ POA. The charge is based on the original delivery address of the product when purchased. This charge is payable in full, prior to any on site attendance. This charge will not include travel expenses (fuel, parking, toll charges etc.) but, will include labour and the parts replacement of electrical or motorised mechanical components, to include electrical motors, foot control boxes, and system control boxes but does not include optional extras such as Vibro or Thermo heat functions. The call out repair charge will not cover items deemed as natural “wear & tear” such as upholstery etc. The call out charge will not cover damage by accident, misuse, or misapplication, or if the product has been modified without permission. Any serial numbers removed or displaced will also result in warranty invalidation. Proof of purchase will be required before any repairs carried out.

13 - Warranty call out, or on-site repairs, will be charged as per the prevailing rate (POA), terms and conditions, but will be refunded (excluding toll, parking or any other costs incurred to carry out the relevant repair) once established that any fault is covered under and within the warranty period and criteria.