f55840 10713 Profiset 3030 HiPath 1100v7 TelUserGuide en 13

HiPath 1100HiPath 1120HiPath 1130HiPath 1150HiPath 1190

Instruction ManualSystem TelephoneProfiset 3030

8xx.bk Seite 1 Dienstag, 26. September 2006 8:30 08

Contents

2

Installation Recommendations................... 3Installation ......................................................................... 4

Profiset 3030 System Telephone ................ 5Characteristics................................................................... 5Status Indication Keys ....................................................... 7Function Keys for Profiset 3030 - S30058-H6202-A1/A2 .. 8Function Keys for Profiset 3030 - S30058-H6202-C5/C6 .. 9

Configuration.............................................. 10Adjusting the Ring Volume.............................................. 10Adjusting the Ring Melody.............................................. 11Adjusting the Reception Volume..................................... 12Dialing Mode ................................................................... 13Display Brightness .......................................................... 14Time Format.................................................................... 15Adjusting the Hands-free Volume ................................... 16Other Settings................................................................. 16

Diagram of the Navigation Menu ............. 18


Installation Recommendations


Installation Recommendations• Place the telephone on a non-slip surface. Polished or

varnished surfaces can be marked by some parts of thetelephone, such as the rubber feet.

• To ensure good hands-free conversation quality, placethe telephone on a flat surface and keep the area in frontof the microphone free of obstructions.

• To avoid interference, keep the telephone at least onemeter away from cordless telephones, mobile telepho-nes, television sets and other electrical equipment.

• The Profiset 3030 telephone must be installed at a maxi-mum distance of 500 meters from the telephone exchan-ge by using a two-pair cable with 0.4mm2 copper wire.

• The telephone must not be exposed directly to the sunor other heat sources, nor be installed in dusty or exces-sively humid locations, as this will reduce its useful life.It should be used at temperatures between 5 ºC and 50ºC and it is not waterproof.

• To clean the telephone, use a damp cloth and avoid abra-sive cleaning products. Do not use a dry cloth, becauseit may cause electrostatic discharges that could damagethe equipment.

• When the telephone reaches the end of its useful life,dispose of it in a way that does not harm the environ-ment, in accordance with local legal requirements.

CE Mark

The device conforms to the EU guideline 99/5/ECC, as attested by the CE mark.

3

U2

Installation Recommendations


Installation

Connecting the Handset to the Telephone:

• Insert the long, straight end of the spiral cord into theconnector with the symbol, until it snaps in.

• Connect the short end to the handset.

• Press the cord into the cable guide.

Line Cord Connection

• Insert one end of the straight cord into the connectorwith the symbol and the other end into the phonejack of the extension to which you want to connect theequipment.

• Press the cord into the cable guide.

Labeling Strip

Your Profiset 3030 telephone has a labeling strip for writingdown names, telephone numbers and functions stored in theprogrammable keys. If you need to change the labels, cut outthe template supplied on the last page of this manual.

4

Profiset 3030 System Telephone


Profiset 3030 System TelephoneThis is a telephone exclusive to the HiPath 1100 and eurosetline systems. It allows direct access to some PABX features,and has special functions for monitoring the status of exter-nal lines and extensions using signals from a group of pro-grammable keys.

CharacteristicsIt has a 3-line display

• The first line displays the MUTE symbol, the repeat callcounter, the repeat call indicator, and the time and date.The time is shown in 24-hour or AM/PM (hours:minutes)format and the date in day/month format (for example,11:13 28/08).

• When you are in operator terminal mode, the number ofunanswered internal, external and recalled calls is shownon the second line (16 digits).

• The messages are shown, 16 characters, on the thirdline.

1. MUTE indicator symbol activated

2. Repeat call counter

3. Time

4. AM/PM indicator

5. Date

6. Repeat call indicator

7. Field for operator terminal

8. Field for alphanumeric characters

5



Profiset 3030 - S30058-H6202-A1/A2

Profiset 3030 - S30058-H6202-C5/C6

1. Handset cradle2. Function keys3. Programmable keys with status indicator LEDs4. Hands-free loudspeaker5. Hands-free microphone6. Display

6



Status Indication Keys

Key off; the extension or external line is free.

Key blinking slowly; a call is parked.

Key blinking faster; an incoming call to the exten-sion has not been answered.

Key blinking fastest; signals an incoming call or a re-call.

Key is on; the extension is busy.

7



Function Keys for Profiset 3030 - S30058-H6202-A1/A2

FWD key forwards calls to an extension or external telephone.

PARK key parks a call.

HOLD key puts a call on hold.

SPEAKER key, activates hands-free mode using mi-crophone and loudspeaker.

REDIAL key redials the last number called1.

MENU key for access to menu-driven configuration settings.

FLASH key invokes the flash function for the exter-nal line.

FEATURE key activates the system functions (for example, Forward, Do not disturb, etc).

MUTE key deactivates voice transmission so the person with whom you are speaking cannot hear you any more. To reactivate voice transmission, press the key again.

Confirmation key

Menu navigation key

Menu navigation key

1.The REDIAL function key is only used for telephone MENU navigation on HiPath 1100 5.2 systems.

8



Function Keys for Profiset 3030 - S30058-H6202-C5/C6NOTE:Profiset 3030 S30058-H6202-C5/-C6 can only be used in Version 5.2.

Navigation KeyShows PREVIOUS option

Navigation Key.Shows NEXT option.

Confirmation KeySelects (confirms) the displayed option.

SPEAKER key, activates hands-free mode using mi-crophone and loudspeaker.

REDIAL key redials the last number called.

MENU key for access to menu-driven configuration settings.

FLASH key invokes the flash function for the exter-nal line.

FEATURE key activates the system functions (for example, Forward, Do not disturb, etc).

MUTE key deactivates voice transmission so the person with whom you are speaking cannot hear you any more. To reactivate voice transmission, press the key again.

9

Configuration


ConfigurationFor greater user convenience, the Profiset 3030 system tele-phone provides some configuration options.

The following keys are used in configuration mode:

Profiset 3030 - S30058-H6202-A1/A2

Profiset 3030 - S30058-H6202-C5/C6

Adjusting the Ring VolumeThe ring volume can be adjusted to 6 levels.The ring volumeis preset to level 6.

Telephone in Idle State:

Replace the handset.

Press this key to enter configura-tion mode.

With the or keys, locate the ring volume option on the display.

Press this key to select thering volume adjustment option.

Use the or keytochange the ring volume.

After choosing a volume level, press this key to confirm.

Continue navigating through the menu options or press the Menu key to finish the configuration.

and or and h

and or and h

Ring Volume 1

Ring Volume 2

or and

10

Configuration


Adjusting the Ring MelodyYou can choose among 3 ring melodies.




With the or keys,locatethe melody option on the display.

Press this key to select the melody selection option.

Use the or keystohear the ring melody.

Choose a melody and press this key to confirm.


melody 1

melody 1

or and

11

Configuration


Adjusting the Reception VolumeThe reception volume on the Profiset 3030 can be adjustedduring a conversation (6 levels).

The reception volume is preset to level 4.

Press this key to enter configuration mode.

With the or keys,locatethe volume RX option on the display.

Press this key to select thevolume RX option.

Use the or keystochange the reception volume.

After choosing a volume level, press this key to confirm.


volume RX 1

volume RX 1

or and

12

Configuration


Dialing ModeIf your system is not working because of a power outage andthe external telephone line has been switched directly toyour Profiset 3030 system telephone, you will need to spec-ify the dialing mode (pulse or tone) for this line, because innormal operation the telephone exchange performs this set-ting automatically.




With the or keys,locatethe mode option on the display.

Press this key to select the mode option.

Use the or keysto choosethe dialing type, Tone or Pulse.

After choosing a dialing mode, press this key to confirm.


Temporary Change of Dialing Mode:

When the telephone is set to PULSE dialing, you may occa-sionally need to temporarily change the dialing mode toTONE dialing.

Example: You want to check your bank balance using yourtelephone banking service. Make the call as you usuallywould and, as soon as the call is completed, press tochange the dialing mode to TONE dialing. When you finishthe call, just hang up and the dialing mode will automaticallyswitch back to PULSE dialing.

Mode tone

Mode tone

or and

13

Configuration


Display BrightnessThe display brightness can be adjusted to 3 levels; it is presetto level 2.




With the or keys,locatethe bright option on the display.

Press this key to select the bright option.

Use the or keyto selectone of the 3 brightness levels.

After choosing a brightness level, press this key to confirm.


bright 1

bright 1

or and

14

Configuration


Time FormatThe time can be shown on the display in 24-hour or AM/PMformat.




With the or keys,locate the format option on the display.

Press this key to select the format option.

Use the or keystoselect 24 hs or am pm.

After choosing a format, press this key to confirm.


Format 24 hs

format am pm

or and

15

Configuration


Adjusting the Hands-free VolumeYou can adjust the hands-free volume (6 levels) on theProfiset 3030 during a conversation.

The hands-free volume is preset to level 4.

Telephone in Hands-free Mode:

Press this key to switch to hands-free mode.


Use the or keystoselect one of the 6 volume levels.

Press this key to finish the configu-ration.

Other SettingsYou can make additional settings with the followingsequence:

vol hands-free 1

+ + Code

Code Description00 Sets DTMF 85/85ms and enables DTMF mode

01 Sets DTMF 140/85ms and enables DTMF mode

16

Configuration


02 Sets pulse dialing open/closed ratio to 2:1(33/66ms) and enables pulse dialing

03 Sets pulse dialing open/closed ratio to 1.5:1(40/60ms) and enables pulse dialing

04 Automatic gain control disabled

05 Automatic gain control enabled

06 Ring frequency discrimination in the 15-75Hzrange (in case of power outage)

07 Ring frequency not discriminated

08 Line impedance 600 Ω (in case of power outage)

09 Line impedance 1000 Ω (in case of power outage)

10 DTMF 85/85ms

11 DTMF 140/85ms

12 Pulse dialing proportion open/closed 2:1(33/66ms)

13 Pulse dialing proportion open/closed 1.5:1(40/60ms)

14 Time format DD/MM

15 Time format MM/DD

20 This code cancels the language setting config-ured by the user (manual configuration) and acti-vates the system's default setting (automatic con-figuration).

21 Portuguese (Brazil)

22 Portuguese (Portugal)

23 English (default)

24 French

25 Spanish

31 Normal level of transmission

32 High level of transmission

33 Very high level of transmission

99 Return to factory programming

Code Description

For more detailed feature explanations, refer toyour telephone exchange’s user guide.

17

Diagram of the Navigation Menu


Diagram of the Navigation Menu

Level 1 Level 2 Level 3

Menu

RING VOLUME

MELODY

MODE

FORMAT

BRIGHT

VOLUME RX

123456

123

TONEPULSE

24 HSAM PM

123

123456

18




Sub

ject

to

ava

ilab

ility

. R

ight

of

mod

ific

atio

n re

serv

ed.

A31003-K1250-B816-13-76191P A31003-K1250-B816-13-7619

Ref. No.:A31003-K1250-B816-13-7619 •Printed in Brazil • 26.09.06

© Siemens Ltda 2006 • Rua Pedro Gusso, 2635 • Curitiba-PR/BR

The information in this document contains general descriptions of the technicaloptions available, which do not always have to be present in individual cases.The required features should therefore be specified in each individual case at the time of closing the contract.

Produzido no Pólo Industrial

de Manaus


Documents

f55840 10713 Profiset 3030 HiPath 1100v7 TelUserGuide en 13