Factors Affecting the Rate of Factors Affecting the Rate of a Chemical Reactiona Chemical Reaction

• 1. temperature• 2. concentration• 3. pressure (gases)• 4. surface area• 5. orientation (molecules must collide in

a specific manner to form a chemical bond)

• 6. nature of the reactants (solid, liquids, gas)

• 7. catalyst

The following events must occur before a reaction can proceed:

1. The reactant particles must collide with each other.

2. The collisions must be of enough energy to overcome the ‘energy barrier’, called the activation energy (more about this on the next slide).

3. The reactants must form new bonds to produce products.

Activation Activation Energy Energy

Defined as:

The minimum energy required to bring about a chemical reaction.

Gasoline for your car would ignite as soon as it came into contact with air.You would burst into flames.

If there were no such thing as ‘activation energy’ life would be very

difficult:

Activation energy is why these things do not happen, there is an energy barrier so most reactions need to be

‘started off’ by putting in some energy.

Activation Energy 2Activation Energy 2

Activation energy for a reaction is

shown on reaction profile diagrams

Reactants

Products

Activated intermediate

Activation energy

H

en

erg

y

1. Temperature1. TemperatureAccording to kinetic theory (do you remember this?) as the temperature increases the particles in a substance move about more quickly.

Reaction at 300C Reaction at 500C

As the temperature increases the number of collisions increases as well as the energy of the collisions. So temperature has a big effect on the rate of reaction. For every 100C increase the rate approximately doubles.

Higher temperature = faster reaction

Acid Particles

Zinc

2. Concentration2. ConcentrationConsider the reaction between zinc and hydrochloric acid: Zn + 2HCl H2 +

ZnCl2

1M hydrochloric acid 2M hydrochloric acid

There are more particles of acid per unit volume in the 2M acid than there are in the 1M acid. So, there will more collisions between the acid and zinc particles in the stronger acid, giving a faster reaction.

Higher concentration = faster reaction

3. Pressure:Gas Reactions3. Pressure:Gas ReactionsThe rate of reaction between gases is

increased by increased pressure.

In effect pressure is the gas equivalent of concentration.

These two gas jars contain the same number of gas particles.

Low pressure, particles far apart.

Higher pressure, particles closer together.

The higher pressure jar has more particles per unit volume which means a higher concentration, hence faster reaction.

Higher pressure = faster Higher pressure = faster reactionreaction

4. Surface Area4. Surface Area

When solids take part in chemical reactions only the surface particles are exposed so they are the only ones that can collide with particles of other reactants.

The surface particles are ‘exposed’ and can react.

‘Inner’ particles are protected and cannot collide with other particles until they become ‘exposed’.

4. More on Surface Area4. More on Surface AreaIf we break up this ‘lump’ into smaller pieces the number of particles has not changed but the there are now more ‘surface’ particles.

There is now a greater surface area with more exposed particles so more collisions can occur, hence faster reaction.

Larger surface Larger surface area = faster area = faster reaction.reaction.

3. Orientation and Efficiency of 3. Orientation and Efficiency of Molecular CollisionsMolecular Collisions

A2 + B2 → 2AB

7. Effect of a Catalyst 7. Effect of a Catalyst

• A catalyst is a substance that increases the speed of a reaction, without being used up. A catalyst can be recovered at the end of a reaction and used again.

• An enzyme is a catalyst• A catalyst reduces the activation energy of a

reaction

.

.

7. Effect of a Catalyst 27. Effect of a Catalyst 2

Activation energy without catalyst.

Activation energy with catalyst.

en

ergy

The lower activation energy in the presence of a catalyst means the reaction will be faster. More of the collisions have enough energy to react. There is a lower ‘energy barrier’.

Catalyst = faster reaction.

Changing the Rate of a Chemical Changing the Rate of a Chemical ReactionReaction

To change the rate of a reaction one or more of the following things must happen:

1. Increase the number of collisions between the reactant particles

2. Increase the energy of the collisions.

3. Decrease the activation energy.

4. Increase the speed of the rate determining step

This is all very well but how can we follow the progress of a chemical

reaction?

Following a Chemical Reaction Following a Chemical Reaction

To find the rate of a chemical reaction we must be able to follow its progress

with time.

We have two choices:

1. Record the increase in product concentration as the reaction progresses.

2. Record the decrease in reactant concentration as the reaction progresses.

Following a Chemical Reaction 2Following a Chemical Reaction 2

As an example consider the reaction between calcium carbonate and hydrochloric acid.

CaCO3 + 2HCl CaCl2 + H2O + CO2

We can follow this reaction by measuring the volume of carbon dioxide produced as the reaction proceeds.

Measure the amount of CO2 collected

Dilute acid

Marble chips

Gas being collected

Following a Chemical Reaction 3Following a Chemical Reaction 3

If you collect data for the total amount of gas produced as the reaction progresses then plot this data on a graph you should get a curve similar to that shown below.

All very well, but what does the graph tell you?

The gradient or slope of the graph shows the rate of the reaction.

Steeper slope = faster reaction.

Volu

me

of

gas/c

m3

Time/sec.

Reaction fastest at the beginning.

Slowing down.

Reaction finished.

More About Rate More About Rate Graphs Graphs

Volu

me

of

gas/c

m3

Time/sec.

Reaction fastest at the beginning.

Slowing down.

Reaction finished.

1. Why is the reaction fastest at the beginning?

2. Why does the reaction slow down?

3. Why does the reaction eventually stop?

1. This is where the concentration of the reactants is highest, therefore fastest reaction.

2. As the reactants are used their concentration decreases so the rate of reaction decreases.

3. One of the reactants is used up, so there can be no further reaction.

Summary: Factors that Affect Summary: Factors that Affect Reaction RateReaction Rate

1. Increasing the surface area gives a faster reaction because more particles are ‘exposed’ to the other reactant.

2. Increasing the concentration increases the rate of reaction because there are more collisions between the reactant particles.

3. Increasing the temperature increases the rate of reaction because the particles move faster and collide more often with greater energy.

4. If the reactants are both of the same nature, ex. All gases, the reaction will proceed at a faster rate. (homogeneous)

5. A catalyst increases the rate of a reaction because it reduces the activation energy so more of the collisions have enough energy to react.

Result of effective collisions