Embed Size (px)
Citation preview
mAChO NAChO®
Chip WarmersFDWD-1-mN and FST-1-mN Series
Installation and Operating manualP/N 07.04.287.00
© 2011 Hatco Corporation
Register Online!(see page 2)
www.hatcocorp.com
Do not operate this equipment unless youhave read and understood the contents ofthis manual! Failure to follow theinstructions contained in this manual mayresult in serious injury or death. Thismanual contains important safetyinformation concerning the maintenance,use, and operation of this product. Ifyou’re unable to understand the contentsof this manual, please bring it to theattention of your supervisor. Keep thismanual in a safe location for futurereference.
No opere este equipo al menos que hayaleído y comprendido el contenido de estemanual! Cualquier falla en el seguimientode las instrucciones contenidas en estemanual puede resultar en un serio lesióno muerte. Este manual contieneimportante información sobre seguridadconcerniente al mantenimiento, uso yoperación de este producto. Si usted nopuede entender el contenido de estemanual por favor pregunte a susupervisor. Almacenar este manual enuna localización segura para la referenciafutura.
Ne pas utiliser cet équipement sans avoirlu et compris le contenu de ce manuel !Le non-respect des instructionscontenues dans ce manuel peut entraînerde graves blessures ou la mort. Cemanuel contient des informationsimportantes concernant l'entretien,l'utilisation et le fonctionnement de ceproduit. Si vous ne comprenez pas lecontenu de ce manuel, veuillez le signalerà votre supérieur. Conservez ce manueldans un endroit sûr pour pouvoir vous yréférer plus tard.
WARNING ADVERTENCIA AVERTISSEMENT
CONTENTS
2Form No. mNm-0811
Safety information that appears in this manual is identified bythe following signal word panels:
WARNING indicates a hazardous situation which, if notavoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if notavoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to personalinjury.
NOTICE
CAUTION
WARNING
INTRODUCTIONThe Hatco macho Nacho® Chip Warmer is designed to holdnacho chips for prolonged periods of time while maintaining that“just-made” quality. Hatco Chip Warmers provide the bestenvironment for food products by regulating the air temperature.macho Nacho models use hot air only (no moisture) that iscirculated through distribution panels at the base. This preventsthe loss of natural oils, eliminating the need to frequentlyreplace stale chips.
Hatco macho Nacho Chip Warmers are products of extensiveresearch and field testing. The materials used were selectedfor maximum durability, attractive appearance, and optimumperformance. Every unit is inspected and tested thoroughlyprior to shipment.
This manual provides installation, safety, and operatinginstructions for macho Nacho Chip Warmers. Hatcorecommends all installation, operating, and safety instructionsappearing in this manual be read prior to installation oroperation of a unit.
Important Owner Information ..............................................2Introduction...........................................................................2Important Safety Information...............................................3model Description.................................................................4model Designation................................................................4Specifications........................................................................5
Plug Configurations .........................................................5Electrical Rating Chart .....................................................5Dimensions......................................................................6
Installation .............................................................................7General ............................................................................7
Operation...............................................................................8General ............................................................................8
maintenance ..........................................................................9General ............................................................................9Cleaning ..........................................................................9Removing the Glass Side Panels ....................................9Replacing a Display Light Bulbs ......................................9
Troubleshooting Guide ......................................................10Options and Accessories...................................................10Limited Warranty.................................................................11Authorized Parts Distributors ............................Back Cover
ImPORTANT OWNER INFORmATIONRecord the model number, serial number (specification labellocated on the operator side of the unit), voltage, and purchasedate of the unit in the spaces below. Please have thisinformation available when calling Hatco for service assistance.
model No. ____________________________________
Serial No. ____________________________________
Voltage ______________________________________
Date of Purchase ______________________________
Register your unit!Completing online warranty registration will prevent delay inobtaining warranty coverage. access the Hatco website atwww.hatcocorp.com, select the Parts & Service pull-downmenu, and click on “Warranty Registration”.
Business 8:00 am to 5:00 Pm
Hours: Central Standard Time (C.S.T.)
(Summer Hours: June to September –
8:00 am to 5:00 Pm C.S.T.
monday through Thursday
8:00 am to 2:30 Pm C.S.T. Friday)
Telephone: (800) 558-0607; (414) 671-6350
E-mail: [email protected]
Fax: (800) 690-2966 (Parts and Service)
(414) 671-3976 (International)
additional information can be found by visiting our web site atwww.hatcocorp.com.
24 Hour 7 Day Parts and ServiceAssistance available in the United Statesand Canada by calling (800) 558-0607.
ImPORTANT SAFETy INFORmATION
Form No. mNm-08113
Use only light bulbs that meet or exceed NationalSanitation Foundation (NSF) standards and are specificallydesigned for food holding areas. Breakage of light bulbsnot specially-coated could result in personal injury and/orfood contamination.
make sure all operators have been instructed on the safeand proper use of the unit.
This unit is not intended for use by children or personswith reduced physical, sensory, or mental capabilities.Ensure proper supervision of children and keep them awayfrom the unit.
hatco Corporation is not responsible for actual foodproduct serving temperature. It is the responsibility of theuser to ensure that food product is held and served at asafe temperature.
This unit has no “user-serviceable” parts. If service isrequired on this unit, contact an Authorized hatco ServiceAgent or contact the hatco Service Department at 800-558-0607 or 414-671-6350; fax 800-690-2966; orInternational fax 414-671-3976.
BURN hAzARD: Some exterior surfaces on the unit will gethot. Use caution when touching these areas.
Locate unit at the proper counter height in an area that isconvenient for use. The location should be level to preventthe unit or its contents from falling accidentally and strongenough to support the weight of the unit and contents.
Transport unit in upright position only. Before moving ortipping unit, secure all glass surfaces, doors, pan rails,and/or skirts with tape, and drain water from humidifiedunits. Failure to do so may result in damage.
Use non-abrasive cleaners and cloths only. Abrasivecleaners and cloths could scratch finish of unit, marringits appearance and making it susceptible to soilaccumulation.
Clean unit daily to avoid malfunctions and maintainsanitary operation.
CAUTION
NOTICE
WARNINGELECTRIC ShOCK hAzARD:
• Plug unit into a properly grounded electrical receptacleof the correct voltage, size, and plug configuration. Ifplug and receptacle do not match, contact a qualifiedelectrician to determine and install proper voltage andsize electrical receptacle.
• Turn OFF power switch, unplug power cord, and allowunit to cool before performing any cleaning,adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is notwaterproof. Do not operate if unit has been submergedor saturated with water.
• Unit is not weatherproof. Locate unit indoors whereambient air temperature is a minimum of 70°F (21°C).
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-clean spray to clean this unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged powercord. The cord must be replaced by hatco, anAuthorized hatco Service Agent, or a person withsimilar qualifications.
• This unit must be serviced by qualified personnel only.Service by unqualified personnel may lead to electricshock or burn.
• Use only Genuine hatco Replacement Parts whenservice is required. Failure to use Genuine hatcoReplacement Parts will void all warranties and maysubject operators of the equipment to hazardouselectrical voltage, resulting in electrical shock or burn.Genuine hatco Replacement Parts are specified tooperate safely in the environments in which they areused. Some aftermarket or generic replacement partsdo not have the characteristics that will allow them tooperate safely in hatco equipment.
FIRE hAzARD: Locate unit a minimum of 1″ (25 mm) fromcombustible walls and materials. If safe distances are notmaintained, discoloration or combustion could occur.
WARNING
Read the following important safety information before using this equipment to avoid serious injury or deathand to avoid damage to equipment or property.
All modelsHatco macho Nacho® Chip Warmers are high-visibilitymerchandisers for warming and displaying nacho chips. Theunique air flow forces warm air to the bottom and is distributedinto the cabinet through holes in the floor panels directingmaximum heat to the chips being served. air is circulated toprevent the loss of natural oils, eliminating the need tofrequently replace stale chips.
macho Nacho’s unique two-door design allows for first-in, first-out chip delivery and permits easy loading and serving. Chipsflow to the customer side of the cabinet when loading throughthe upper door, and slanted floor panels slide the heated chipsback to the lower door for serving.
User-friendly controls make the macho Nacho units easy tooperate. Common controls include a POWER ON/OFF (I/O)switch and a TEmPERaTURE control. Units are equipped witha 6′ (1829 mm) power cord with plug. Only minimal maintenanceis required, and the glass side panels and floor panels areremovable for easy cleaning.
FDWD-1-mN modelThe FDWD-1-mN model is built of stainless steel with temperedglass sides and doors. The unit holds up to 25 lbs. (11 kg) ofchips.
Figure 1. FDWD-1-mN
POWER ON/OFF (I/O) Switch
Temperature Control
Upper Door
Lower Door
FST-1-mN modelThe FST-1-mN model is built of stainless steel and aluminumwith tempered glass sides and doors. In addition to the controlslisted above, this model includes a CaBINET TEmP monitorthat displays the internal temperature of the cabinet. ananodized bronze exterior is standard. The unit holds up to 40lbs. (18 kg) of chips.
Figure 2. FST-1-mN
NOTE: Refer to the OPTIONS aND aCCESSORIES section foradditional options available for the above models.
TemperatureControl
POWER ON/OFF (I/O)Switch
Temperature Monitor
Upper Door
Lower Door
mODEL DESCRIPTION
mODEL DESIGNATION
4Form No. mNm-0811
Figure 3. model Designation
X X X X - 1 - MNFDWD = 25 lbs. chip capacity
FST = 40 lbs. chip capacity One Door
Macho Nacho unit
model Voltage hertz Watts Amps Plug Configuration Shipping Weight
FDWD-1-mN 100 60 1106 11.1 NEma 5-15P 99 lbs. (45 kg)
120 60 1080 9.0 NEma 5-15P 99 lbs. (45 kg)
220 50/60 950 4.3 CEE 7/7 Schuko 99 lbs. (45 kg)
240 50/60 1129 4.7 BS-1363 or aS-3112 99 lbs. (45 kg)
220–230 (CE) 50/60 950–1036 4.3–4.5 CEE 7/7 Schuko 99 lbs. (45 kg)
230–240 (CE) 50/60 1036–1129 4.5–4.7 BS-1363 99 lbs. (45 kg)
FST-1-mN 120 60 1245 10.4 NEma 5-15P 132 lbs. (60 kg)
220 50/60 1219 5.6 CEE 7/7 Schuko 132 lbs. (60 kg)
240 50/60 1252 5.2 BS-1363 132 lbs. (60 kg)
220–230 (CE) 50/60 1219–1332 5.6–5.8 CEE 7/7 Schuko 132 lbs. (60 kg)
230–240 (CE) 50/60 1150–1252 5.0–5.2 BS-1363 132 lbs. (60 kg)
SPECIFICATIONS
Form No. mNm-08115
Plug ConfigurationsUnits are supplied from the factory with an electrical cord andplug installed. Plugs are supplied according to the applications.
ELECTRIC ShOCK hAzARD: Plug unit into a properlygrounded electrical receptacle of the correct voltage, size,and plug configuration. If plug and receptacle do notmatch, contact a qualified electrician to determine andinstall proper voltage and size electrical receptacle.
NOTE: Specification label is located on the operator side of theunit. See label for serial number and verification of unitelectrical information.
WARNING
Figure 4. Plug Configurations
NOTE: Receptacle not supplied by Hatco.
NEMA 5-15P
CEE 7/7 Schuko AS-3112
BS-1363
The shaded areas contain electrical information for International models only.
Electrical Rating Chart
modelWidth
(A)Depth
(B)height
(C)*Footprint Width (D)
Footprint Depth (E)
FDWD-1-mN 19-3/8″
(492 mm)
24″
(608 mm)
28-3/4″
(729 mm)
19-1/16″
(485 mm)
15-3/8″
(390 mm)
FST-1-mN 22-7/8″
(579 mm)
27″
(686 mm)
32-3/4″
(831 mm)
19″
(483 mm)
18-11/16″
(475 mm)
modelCabinet Opening
WidthUpper Door
Opening heightLower Door
Opening height
FDWD-1-mN 16-3/8″
(416 mm)
9-1/8″
(233 mm)
9-1/16″
(230 mm)
FST-1-mN 18-5/8″
(474 mm)
11-3/16″
(285 mm)
9-7/8″
(251 mm)
SPECIFICATIONS
6Form No. mNm-0811
A
D E
C
B
Front View Side View
* add 3″ (76 mm) to the height of the unit if the 4″ leg option is installed.
Dimensions
Door Opening Dimensions
Figure 5. Dimensions
6. Place the unit in the desired location. Two people arerequired for this step.
• Locate the unit in an area where the ambient airtemperature is constant and a minimum of 70° F (21° C).avoid areas that may be subject to active air movementsor currents (i.e., near exhaust fans/hoods and airconditioning ducts).
• make sure the unit is at the proper counter height in anarea convenient for use.
• make sure the countertop is level and strong enough tosupport the weight of the unit and food product.
Figure 6. assembling a FDWD-1-mN model
ChipDeflector
ChipDeflector
Flange
Floor Panelsw/ Holes
Pin
Decal (3)
INSTALLATION
Form No. mNm-08117
GeneralHatco macho Nacho® Chip Warmers are shipped with mostcomponents installed and ready for operation. The followinginstallation instructions must be performed before plugging inand operating the cabinet.
ELECTRIC ShOCK hAzARD: Unit is not weatherproof.Locate unit indoors where the ambient air temperature isa minimum of 70°F (21°C).
FIRE hAzARD: Locate unit a minimum of 1″ (25 mm) fromcombustible walls and materials. If safe distances are notmaintained, discoloration or combustion could occur.
Locate unit at the proper counter height in an area that isconvenient for use. The location should be level to preventthe unit or its contents from falling accidentally and strongenough to support the weight of the unit and contents.
Transport unit in upright position only. Before moving ortipping unit, secure all glass surfaces, doors, pan rails,and/or skirts with tape, and drain water from humidifiedunits. Failure to do so may result in damage.
1. Remove the unit from the carton. Two people are requiredfor this step.
2. Remove the information packet.
NOTE: To prevent delay in obtaining warranty coverage,complete online warranty registration. See theImPORTaNT OWNER INFORmaTION section fordetails.
3. Remove tape and protective packaging from all surfaces ofthe unit, shelves, and any accessories.
• Legs — The cabinets are shipped with four rubber feetattached to the bottom of the unit. For cabinets with theaccessory 4″ (102 mm) adjustable legs, see theOPTIONS aND aCCESSORIES section for installationinstructions.
4. Install the chip deflector behind the upper door.
• FDWD-1-mN models—Two holes on the chip deflectorflange slide over two pins at the bottom of the upper doorframe.
• FST-1-mN models—The chip deflector flange slidesbehind the flange at the bottom of the upper door frame.
5. Install the decals on the three stainless steel side panelsabove the glass side panels.
a. Clean the side panels with a non-oily cleaner, such asrubbing alcohol.
b. When the side panels have dried, remove the protectivebacking from the decal and apply it to the panel.
c. Remove any air pockets or bubbles behind the decal byrubbing gently with a soft cloth, working from the centerof the decal towards the outer edges.
WARNING
CAUTION
GeneralUse the following procedures to operate a macho Nacho® ChipWarmer.
Read all safety messages in the ImPORTANT SAFETyINFORmATION section before operating this equipment.
Startup1. Plug unit into a properly grounded electrical receptacle of
the correct voltage, size, and plug configuration. See theSPECIFICaTIONS section for details.
2. move the Power ON/OFF (I/O) switch to the ON (I) position.
3. Set the TEmPERaTURE Control to the desired temperaturesetting.
4. allow 20 minutes to heat the cabinet to operatingtemperature.
5. Open the upper door and fill the unit with chips.
BURN hAzARD: Some exterior surfaces on the unit will gethot. Use caution when touching these areas.
Shutdown1. move the Power ON/OFF (I/O) switch to the OFF (O)
position.
2. allow the unit to cool, and perform the “Cleaning” procedurein the maINTENaNCE section of this manual.
WARNING
WARNING
Figure 7. FDWD-1-mN Controls
Figure 8. FST-1-mN Controls
POWER ON/OFF (I/O) Switch
TEMPERATUREControl
POWER ON/OFF (I/O) Switch
CABINET TEMPMonitor
TEMPERATUREControl
Form No. mNm-08118
OPERATION
GeneralHatco macho Nacho Chip Warmers are designed for maximumdurability and performance, with minimum maintenance.
ELECTRIC ShOCK hAzARD:• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning,adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is notwaterproof. Do not operate if unit has been submergedor saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-clean spray to clean this unit.
• Use only Genuine hatco Replacement Parts whenservice is required. Failure to use Genuine hatcoReplacement Parts will void all warranties and maysubject operators of the equipment to hazardouselectrical voltage, resulting in electrical shock or burn.Genuine hatco Replacement Parts are specified tooperate safely in the environments in which they areused. Some aftermarket or generic replacement partsdo not have the characteristics that will allow them tooperate safely in hatco equipment.
This unit has no “user-serviceable” parts. If service isrequired on this unit, contact an Authorized hatco ServiceAgent or contact the hatco Service Department at 800-558-0607 or 414-671-6350; fax 800-690-2966; orInternational fax 414-671-3976.
CleaningTo preserve the finish of the unit, perform the following cleaningprocedure daily.
Use non-abrasive cleaners and cloths only. Abrasivecleaners and cloths could scratch the finish of the unit,marring its appearance and making it susceptible to soilaccumulation.
1. Turn off the unit, unplug the power cord, and allow the unitto cool.
2. Remove the door panel assembly for better access to theinside of the unit.
• FDWD-1-mN models—Pull out and rotate the lockingpins in the upper mounting brackets at the top of eachside of the door panel assembly. Pull the door panelassembly up and away from unit.
• FST-1-mN models—Lift up the door panel assembly andpull off of the four mounting pins (two on each side of theassembly).
3. Empty all remaining food product from unit.
4. Wipe down all interior and exterior metal surfaces with adamp cloth. Stubborn stains may be removed with a goodnon-abrasive cleaner. Clean hard to reach areas using asmall brush and mild soap.
NOTE: The floor panels are removable for ease of cleaning.The cabinet floor is accessible for cleaning when thefloor panels are removed.
NOTICE
WARNING
5. Clean the glass side panels and door panels using ordinaryglass cleaner and a damp, soft cloth or paper towel. Theside panels are removable for detailed cleaning, ifnecessary. Refer to the “Removing the Glass Side Panels”procedure in this section for removal.
6. Secure the door panel assembly to the unit.
• FDWD-1-mN models—Set the door panel assembly onthe bottom bracket. align the mounting holes at the topof the door panel assembly with the locking pins in thetwo upper mounting brackets. Release the locking pinsby rotating slightly, and make sure they lock into the doorpanel assembly.
• On FST-1-mN models—align the four holes on the doorpanel assembly with the four mounting pins on the unit,and guide the door panel assembly down into position.
Removing the Glass Side Panels1. Lift the glass panel out of the bottom channel of the cabinet.
2. Pull the lower edge away from the cabinet.
3. Carefully lower the glass until the top clears the cabinet.
Replacing the Glass Panel1. Position the glass panel with the top edge under the top
cabinet lip, and raise the glass until it clears the bottomchannel of the cabinet.
2. move the bottom of the glass towards the cabinet until theglass rests against the cabinet frame.
3. Carefully lower the glass until it rests in the bottom channelof the cabinet.
Replacing Display Light Bulbs
Use only light bulbs that meet or exceed NationalSanitation Foundation (NSF) standards and are specificallydesigned for food holding areas. Breakage of light bulbsnot specially coated could result in personal injury and/orfood contamination.
The display lights are incandescent light bulbs that illuminatethe warming area. Each bulb has a special coating to guardagainst injury and food contamination in the event of breakage.
1. Turn off the unit, unplug the power cord, and allow the unitto cool.
2. Unscrew the light bulb from the unit and replace it with anew, specially-coated incandescent light bulb.
NOTE: Hatco shatter-resistant light bulbs meet NSF standardsfor food holding and display areas. For 100 and 120 voltapplications, use Hatco P/N 02.30.043.00. For 220,240,, 220–230, and 230–240 volt applications, useHatco P/N 02.30.058.00.
WARNING
9Form No. mNm-0811
mAINTENANCE
Symptom Probable Cause Corrective Action
Display light(s) not working. Light bulb(s) loose or defective. Re-install or replace light bulb(s).
Unit operates, but is not circulatingair inside cabinet.
Blower motor is defective. Contact authorized Service agent or Hatco forassistance.
The correct voltage may not be suppliedto blower.
Contact authorized Service agent or Hatco forassistance.
Unit is plugged in, but nothingworks.
No power to unit. Check electrical receptacle and verify thatpower supply matches specifications on unit.If receptacle is not working, check circuitbreaker and reset, or plug unit into a differentknown working receptacle.
Power cord connections are loose ordisconnected.
Contact authorized Service agent or Hatco forassistance.
Power cord is damaged. Contact authorized Service agent or Hatco forassistance.
Defective ON/OFF switch. Contact authorized Service agent or Hatco forassistance.
Unit is not producing any “hot air”inside cabinet.
Safety high-limit is tripped or open. Contact authorized Service agent or Hatco forassistance.
Incorrect voltage supplied to heatingelement.
Contact authorized Service agent or Hatco forassistance.
Blower motor is not working. Check blower motor — refer to Symptom “Unitoperates, but is not circulating air insidecabinet.”
air heating element is defective. Contact authorized Service agent or Hatco forassistance.
OPTIONS AND ACCESSORIES
TROUBLEShOOTING GUIDE
10Form No. mNm-0811
This unit must be serviced by trained and qualifiedpersonnel only. Service by unqualified personnel may leadto electric shock or burn.
WARNINGELECTRIC ShOCK hAzARD: Turn OFF power switch,unplug power cord, and allow unit to cool beforeperforming any cleaning, adjustments, or maintenance.
WARNING
4″ (102 mm) Adjustable LegsThe 4″ (102 mm) adjustable legs are used to add additionalheight to the unit.
1. Remove the chip deflector and the floor panels and securethe doors with tape.
2. Carefully lay the unit on its side. Two people are requiredfor this step.
3. Remove the four rubber feet.
4. Screw the 4″ (102 mm) legs intothe holes in the bottom cover. afterall the legs are tightened, returnthe unit to its upright position. If theunit is not level or rocks, turn theadjustable tip of the appropriate legto level the unit.
Lengthen
Shorten
Adjustable Tip
halogen Display Light Bulbs
Shatter-resistant halogen display light bulbscan be ordered in place of the standardincandescent display light bulbs. The bulbshave a special coating to guard against injuryand food contamination in the event ofbreakage. For 100 and 120 volt applications,use Hatco P/N 02.30.081.00. For 220, 240,220–230, and 230–240 volt applications, useHatco P/N 02.30.082.00.
LImITED WARRANTy
Form No. mNm-081111
1. PRODUCT WARRANTyHatco warrants the products that it manufactures (the“Products”) to be free from defects in materials andworkmanship, under normal use and service, for a period ofone (1) year from the date of purchase when installed andmaintained in accordance with Hatco’s written instructions or18 months from the date of shipment from Hatco. Buyer mustestablish the Product’s purchase date by registering theProduct with Hatco or by other means satisfactory to Hatco inits sole discretion.
Hatco warrants the following Product components to be freefrom defects in materials and workmanship from the date ofpurchase (subject to the foregoing conditions) for the period(s)of time and on the conditions listed below:
a) One (1) year Parts and Labor PLUS One (1)Additional
year Parts-Only Warranty:Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HWB Series (metal sheathed)
b) One (1) year Parts and Labor PLUS Four (4) years Parts-Only Warranty on pro-rated terms that hatco will explain at Buyer’s request:3CS and FR Tanks
c) One (1) year Parts and Labor PLUS Nine (9) years Parts-Only Warranty on:Electric Booster Heater Tanks
Gas Booster Heater Tanks
d) Ninety (90) Day Parts-Only Warranty: Replacement Parts
THE FOREGOING WaRRaNTIES aRE EXCLUSIVE aND INLIEU OF aNY OTHER WaRRaNTY, EXPRESSED ORImPLIED, INCLUDING BUT NOT LImITED TO aNY ImPLIEDWaRRaNTY OF mERCHaNTaBILITY OR FITNESS FOR aPaRTICULaR PURPOSE OR PaTENT OR OTHERINTELLECTUaL PROPERTY RIGHT INFRINGEmENT.Without limiting the generality of the foregoing, SUCHWaRRaNTIES DO NOT COVER: Coated incandescent lightbulbs, fluorescent lights, heat lamp bulbs, coated halogen lightbulbs, halogen heat lamp bulbs, xenon light bulbs, LED lighttubes, glass components, and fuses; Product failure in boostertank, fin tube heat exchanger, or other water heating equipmentcaused by liming, sediment buildup, chemical attack, orfreezing; or Product misuse, tampering or misapplication,improper installation, or application of improper voltage.
2. LImITATION OF REmEDIES AND DAmAGESHatco’s liability and Buyer’s exclusive remedy hereunder will belimited solely, at Hatco’s option, to repair or replacement usingnew or refurbished parts or Product by Hatco or a Hatco-authorized service agency (other than where Buyer is locatedoutside of the United States, Canada, United Kingdom, oraustralia, in which case Hatco’s liability and Buyer’s exclusiveremedy hereunder will be limited solely to replacement of partunder warranty) with respect to any claim made within theapplicable warranty period referred to above. Hatco reservesthe right to accept or reject any such claim in whole or in part.In the context of this Limited Warranty, “refurbished” means apart or Product that has been returned to its originalspecifications by Hatco or a Hatco-authorized service agency.Hatco will not accept the return of any Product without priorwritten approval from Hatco, and all such approved returns shallbe made at Buyer’s sole expense. HaTCO WILL NOT BELIaBLE, UNDER aNY CIRCUmSTaNCES, FORCONSEQUENTIaL OR INCIDENTaL DamaGES, INCLUDINGBUT NOT LImITED TO LaBOR COSTS OR LOST PROFITSRESULTING FROm THE USE OF OR INaBILITY TO USE THEPRODUCTS OR FROm THE PRODUCTS BEINGINCORPORaTED IN OR BECOmING a COmPONENT OFaNY OTHER PRODUCT OR GOODS.
Printed in U.S.a. august 2011 P/N 07.04.287.00 Form No. mNm-0811
HATCO CORPORATIONP.O. Box 340500
Milwaukee, WI 53234-0500 U.S.A.(800) 558-0607 (414) 671-6350
Parts and Service Fax (800) 690-2966International Fax (414) [email protected]
www.hatcocorp.com
hATCO AUThORIzED PARTS DISTRIBUTORSALABAmAJones mcLeod appl. Svc.Birmingham 205-251-0159
ARIzONAService Solutions GroupPhoenix 602-234-2443
Byassee Equipment Co.Phoenix 602-252-0402
CALIFORNIAIndustrial ElectricCommercial Parts & Service, Inc.Huntington Beach 714-379-7100
Chapman appl. ServiceSan Diego 619-298-7106
P & D applianceCommercial Parts & Service, Inc.S. San Francisco 650-635-1900
COLORADOHawkins Commercial applianceEnglewood 303-781-5548
FLORIDAWhaley Foodservice RepairJacksonville 904-725-7800
3Wire Nass Service Co., Inc.Orlando 407-425-2681
B.G.S.I.Pompano Beach 954-971-0456
Comm. appliance ServiceTampa 813-663-0313
GEORGIATWC Servicesmableton 770-438-9797
Heritage Service GroupNorcross 866-388-9837
Southeastern Rest. Svc.Norcross 770-446-6177
hAWAIIBurney’s Comm. Service, Inc.Honolulu 808-848-1466
Food Equip Parts & ServiceHonolulu 808-847-4871
ILLINOISParts TownLombard 708-865-7278
Eichenauer Elec. ServiceDecatur 217-429-4229
midwest Elec. appl. ServiceElmhurst 630-279-8000
Cone’s Repair Servicemoline 309-797-5323
INDIANAGCS ServiceIndianapolis 317-545-9655
IOWAElectric motor Service Co.Davenport 319-323-1823
Goodwin Tucker GroupDes moines 515-262-9308
KENTUCKyService Solutions GroupLexington 859-254-8854
Service Solutions GroupLouisville 502-451-5411
LOUISIANAChandlers Parts & ServiceBaton Rouge 225-272-6620
mARyLANDElectric motor ServiceBaltimore 410-467-8080
GCS ServiceSilver Spring 301-585-7550
mASSAChUSETTSace Service Co., Inc.Needham 781-449-4220
mIChIGANBildons appliance ServiceDetroit 248-478-3320
Commercial Kitchen ServiceBay City 517-893-4561
midwest Food Equip. ServiceGrandville 616-261-2000
mINNESOTAGCS ServicePlymouth 800-345-4221
mISSOURIGeneral PartsKansas City 816-421-5400
Commercial Kitchen ServicesSt. Louis 314-890-0700
Kaemmerlen Parts & ServiceSt. Louis 314-535-2222
NEBRASKAanderson ElectricOmaha 402-341-1414
NEVADABurney’s CommercialLas Vegas 702-736-0006
Hi. Tech Commercial ServiceN. Las Vegas 702-649-4616
NEW JERSEyJay Hill RepairFairfield 973-575-9145
Service PlusFlanders 973-691-6300
NEW yORKacme american Repairs, Inc.Brooklyn 718-456-6544
alpro Service Co.Brooklyn 718-386-2515
appliance InstallationBuffalo 716-884-7425
Duffy’s Equipment Services, Inc.Buffalo 800-836-1014
3Wire NorthernPlattsburgh 800-634-5005
Duffy’s Equipment Services, Inc.Sauquoit 800-836-1014
J.B. Brady, Inc.Syracuse 315-422-9271
NORTh CAROLINAauthorized applianceCharlotte 704-377-4501
OhIOakron/Canton Comm. Svc. Inc.akron 330-753-6635
Service Solutions GroupCincinnati 513-772-6600
Commercial Parts and ServiceColumbus 614-221-0057
Electrical appl. Repair ServiceBrooklyn Heights 216-459-8700
E. a. Wichman Co.Toledo 419-385-9121
OKLAhOmAHagar Rest. Service, Inc.Oklahoma City 405-235-2184
Krueger, Inc.Oklahoma City 405-528-8883
OREGONRon’s Service, Inc.Portland 503-624-0890
PENNSyLVANIAElmer Schultz ServicesPhiladelphia 215-627-5401
FaST Comm. appl. ServicePhiladelphia 215-288-4800
appliance Installation & ServicePittsburgh 412-809-0244
K & D Service Co.Harrisburg 717-236-9039
Electric Repair Co.Reading 610-376-5444
RhODE ISLANDmarshall Electric Co.Providence 401-331-1163
SOUTh CAROLINAWhaley Foodservice RepairW. Columbia 803-791-4420
TENNESSEECamp Electricmemphis 901-527-7543
TEXASGCS ServiceFort Worth 800-433-1804
armstrong Repair ServiceHouston 713-666-7100
Cooking Equipment Specialistmesquite 888-866-9276
Refrigerated Specialist, Inc.mesquite 888-866-9276
Commercial Kitchen Repair Co.San antonio 210-735-2811
UTAhLa monica’s Rest. Equip. Servicemurray 801-263-3221
VIRGINIADaubersNorfolk 757-855-4097
DaubersSpringfield 703-866-3600
WAShINGTON3Wire Restaurant applianceSeattle 800-207-3146
WISCONSINa.S.C., Inc.madison 608-246-3160
a.S.C., Inc.milwaukee 414-543-6460
CANADAALBERTAKey Food Equipment ServiceEdmonton 780-438-1690
BRITISh COLUmBIAKey Food Equipment ServiceVancouver 604-433-4484
Key Food Equipment ServiceVictoria 250-920-4888
mANITOBAair Rite, Inc.Winnipeg 204-895-2300
NEW BRUNSWICKEmR Services, Ltd.moncton 506-855-4228
ONTARIOR.G. Henderson Ltd.Toronto 416-422-5580
Choquette - CKS, Inc.Ottawa 613-739-8458
QUÉBECChoquette - CKS, Inc.montreal 514-722-2000
Choquette - CKS, Inc.Québec City 418-681-3944
UNITED KINGDOm
marren GroupNorthants +44(0)1933 666233
Register your unit online!See ImPORTaNT OWNER INFORmaTION
section for details.
