*The “TEMP-SURE” requires a separate 208-230v 3 phase or208-240v 1 phase.

Is your Low Temp dishmachine lacking an adequatesupply of hot water to assure proper sanitation istaking place in the dishroom? We have the answer -“CMA TEMP-SURE”. Rather than replace your existingwater heater with something larger and moreexpensive, add the “TEMP-SURE” booster heater toyour machine. The “TEMP-SURE” is mounted to theside of dishmachine, not requiring any of your valuable kitchen space. The “TEMP-SURE” providesan additional 40 degrees of temperature rise to yourincoming dishmachine water supply, which will helpprevent your existing water supply source frombeing over burdened. Have “PEACE OF MIND” thatproper dishware sanitation is taking place and preventing health risks. (Available on most CMA dishmachines).

The “TEMP-SURE” can be built-in at the factory, orit can be purchased separately with a field kit forfield installation.

DISHMACHINES

12700 KNOTT STREETGARDEN GROVE, CALIF. 92841800-854-6417•714-898-8781•FAX 714-895-2141www.cmadishmachines.com

Model B (Double)Also Available as Corner B

Features A Hot Water Booster Option for Peace of MindFeatures A Hot Water Booster Option for Peace of Mind

FEATURING CMA TEMP-SUREBOOSTER HEATERS

FEATURING CMA TEMP-SUREBOOSTER HEATERS

Model E-AHAlso Available as E-Corner

Booster Heater

Booster Heater

Booster Heater

Model ESTAlso Available as Straight or Corner

4-2019

Hot Water Booster Heater

Hot WaterBooster Heater

PN: 10108.40

CMA

®

Registered Trademark

ULR

LISTEDCOMMERCIALDISHWASHER

864T

USC

TEMP-SURE FLYER REV 1-2017 (Ali logo on back) 4-8-2019_Layout 1 4/11/19 10:47 AM Page 1

The CMA-Temp-SureTM option assures a continuous supply of140°F hot water resulting in excellent d i s hm a c h i n e p e r f o rm a n c e . T h e h e a t e r i s custom-designed for fill anddump CMA single tank dishwashers as a factory added option oran infield add-on. The heater will also fit most competitor’s single tankdishmachines.

FRONT BACK

HEATER ROCKER SWITCH

1/2" MALE PIPE THREADS

HEATER ROCKER SWITCH

7"

834/ "

*INLET

OUTLET

CMA Dishmachines 12700 Knott Street, Garden Grove CA 92841• 800-854-6417 • 714-898-8781 • Fax: 714-895-2141 • www.cmadishmachines.comCMA reserves the right to modify specifications or discontinue models without prior notification.

PN: 10108.40 © 4-2019 CMA, Inc.

SPECIFICATIONS:

MODEL: CMA TEMP-SURETM USA METRICMIN. INCOMING WATER TEMP. 100°F (55°C)RISE 40°F (22°C)AVAILABLE HOT WATER 90 GPH (341LPH)HEATER TANK CAPACITY 2.6 GAL (9.8L)ELECTRICAL RATING VOLTS PHASE AMPS

208 1 44240 1 51208 3 26240 3 30

CHANGES FOR 1-PHASE(TIE STRAPS CHANGED AS SHOWN)

ON HEATER

T2

TOPT1

L-2L-2L-1

L-1

* CAUTION: WATER SOLENOID MUST BEPLUMBED AHEAD OF HEATER INLET. HEATERIS NOT A PRESSURE VESSEL.

Hot Water Assurance System For Dump And Fill Style

Dishwashers

CMA TEMP-SURETM

LEFT SIDE RIGHT SIDE

HEATER ROCKER SWITCH

1/2" MALE PIPE THREADS 1/2" MALE PIPE THREADS

5/16" MOUNTING HOLES (4)

1" ELECTRICAL INLET

16/79 "

25"

24"

*INLET

OUTLET

L-3

L-2

L-1

T-3

3

28

T-2

T-1

THERMOSTAT

HIGH LIMITSWITCH

ROCKERSWITCH

REDRED

BLUE

RED

Power Supply: Hook Up Wire With Highest Voltage On L-2.

GROUND

TOP

3 PHASE WIRE SCHEMATIC

L-1

L-3L-2

DISHMACHINES

CMA

®

Registered Trademark

ULR

LISTEDCOMMERCIALDISHWASHER

864T

USC

Advisory: CMA does NOT endorse “Tankless On-Demand” waterheaters for use on CMA Dishmachine products. CMA DOES endorse,and highly recommends, the standard “tank” style water heaters, sizedproperly to handle each particular facility with their water heatingrequirements.

• Plumbing connections must be made by a qualified service company who will comply with all available Federal, State, and Local Health, Plumbingand Safety codes.

WARNINGS:

• CMA recommends utilizing a water softening system to maintain water hardness measurements of 3.5 gpg (grains per gallon) or less. This willassure maximum results and optimum operation of the dishmachine.

Temp-Sure Sheet Back 4-8-2019_Temp-Sure Sheet Back 4/11/19 10:50 AM Page 1