Fibre Plate _O & M

7/31/2019 Fibre Plate _O & M

1/28

Rechargeable Fibre Plate

Nickel CadmiumBatteries

USERS MANUAL

HBL POWER SYSTEMS LIMITEDHYDERABAD INDIA


2/28

CONTENTS

1.0 TECHNICAL SPECIFICATION 1

2.0 INTRODUCTION 2

3.0 SAFETY PRECAUTIONS 4

4.0 RECEIVING THE SHIPMENT 5

5.0 STORAGE 6

6.0 INSTALLATION 8

7.0 ELECTROLYTE PREPARATION 10

8.0 ELECTROLYTE FILLING 11

9.0 CHARGING 12

10.0 MAINTENANCE 14

11.0 DOS AND DO NOTS 19

12.0 DM/ DI WATER SPECIFICATION 21

13.0 SERVICE LOG 22 -23

14.0 TOOLS & ACCESSORIES 24

15.0 DRAWINGS 25

16.0 TEST CERTIFICATE 26


3/28

2

2.0 INTRODUCTION

We thank you for purchasing our reliable and long life nickel cadmium fibre platebattery. Please read and follow the instructions given in this manual to obtain thebest performance and life from your battery. Inspect the battery at regular intervalsand use the service log sheet provided at the end of the manual for maintaining therecords. Contact Customer Service, for any additional help and guidance that youmay require.

2.1 ELECTROCHEMISTRY

The basic principle of the rechargeable battery is the conversion of electrical energyinto chemical energy and vice versa. The storage battery consists of a number ofindividual cells connected in series to produce the required voltage. Each cellconsists of positive plates (containing nickel hydroxide as the active constituent)and negative plates (containing cadmium hydroxide) immersed in a solution ofpotassium hydroxide in DM/DI water with lithium hydroxide as an additive.

The simplified overall reversible electrochemical reaction given below produces anominal discharge voltage of 1.2 volts per cell:

Charge

2 Ni(OH)2 + Cd(OH)2 2 NiOOH + Cd + 2H2O

Discharge

When the cell is charged, the active materials initially present as hydroxides arechanged. The cadmium hydroxide is reduced to cadmium and nickel hydroxideattains a higher degree of oxidation. On discharge, the process is reversed and theactive materials revert to their original state.

The potassium hydroxide electrolyte doesnt take part in these reactions and actsonly as a carrier of ions. The lithium hydroxide additive in the electrolytesignificantly increases the life of the cell since it has a beneficial effect on thepositive electrodes. This beneficial effect is more pronounced at higher operationaltemperatures.

2.2 CONSTRUCTION

The active material in each electrode is impregnated in the pores of the Nickel

coated polypropylene fibre current collector. The Nickel-plated tabs are welded onthe extra nickel portion of the plate. Several plates of same polarity are either boltedto the terminal post or welded to the terminal post. Several plates of the samepolarity are either bolted to the terminal post or welded to the terminal post.Negative and positive plate groups are interleaved so that plates of oppositepolarities are alternated. The plate groups are insulated from one another by usingmicro-porous separators. The plate block is firmly strapped together using asuitable number of polypropylene straps.


4/28

3

The cell container is of the either polypropylene or stainless steel. Matching cell lidsare made of the same material as that of the cell container. Mirror welding isemployed for thermally fusing the mating surfaces of polypropylene cell containersand lids, while TIG fusion welding is employed in case of stainless steel cellcontainers and lids. The choice of material depends on the application and operatingconditions. The polypropylene containers are translucent and completely free fromcorrosion in wet and saline conditions. The assembly is compact and easy, and thepolypropylene has high impact resistance.

Polypropylene cells are assembled on steel racks with step arrangement in order topermit visual electrolyte level maintenance checks. Alternatively, polypropylene cellsare mounted in stainless steel crates, each holding a suitable number of cells to suitthe space constrained battery boxes as in the case of mobile applications.

Steel cell are mounted in insulated wooden crates, each holding a suitable number ofcells to suit the space constrained battery boxes as in the case of mobileapplications. The wooden crates are also placed in steel racks (without the steparrangement) for stationary applications.


5/28

4

3.0 SAFETY PRECAUTIONS

3.1 ELECTROLYTE

The alkaline electrolyte (solution of potassium hydroxide in DM/DI water) is a strongcaustic agent. Wear rubber gloves, eye protection and long sleeved clothing whenworking on the battery. Before working with electrolyte, make sure that water for

washing is easily available. If electrolyte is splashed on the skin or clothing, washimmediately with water for 10 to 15 minutes. If eyes are affected, flood with waterfollowed by eye wash solution and obtain immediate medical attention.

3.2 KEEP FLAMES AWAY

The battery will produce a mixture of oxygen and hydrogen gases during the lastportion of high rate charging.

Do not adjust connections etc., while charging or in the first hour after charging.

Discharge any possible static electricity from clothes by touching earth-connectedpart.

Do not smoke in the battery room.

Keep the battery location well ventilated to prevent buildup of the oxygen andhydrogen gases, and do not cover the battery during charging.

3.3 TOOLS

Use tools with insulated handles / surfaces.

Do not place or drop metal objects on top of the battery.

Remove rings, wristwatch, loose coins from the pockets and articles of clothing withmetal parts that might come in contact with the battery terminals.


6/28

5

4.0 RECEIVING THE SHIPMENT

4.1 UNPACKING AND INSPECTION

Do not over-turn the packages.

Unpack the batteries immediately upon the arrival and inspect for possible damagein shipment.

Make sure that small packages are not thrown out together with the packingmaterial.

Check that all the material listed in the packing list has been received.

PLEASE INFORM HBL IMMEDIATELY IN CASE OF ANY DAMAGE ORSHORTAGES IN THE CONSIGNMENT.

4.2 SHIPPING METHOD I

THE BATTERY SHIPPED IN FILLED AND CHARGED CONDITION

Remove immediately the transport seal (red plastic film) from the vent cap. Removethe transit cap (blue/red), wherever mounted on cell terminals for big size cells.

Check the electrolyte level in the cells and add electrolyte if necessary.

The battery is then ready for installation or storing.

THE BATTERY MUST NEVER BE CHARGED WITH THE TRANSPORT SEAL INPLACE AS THIS CAN CAUSE PERMANENT DAMAGE.

4.3 SHIPPING METHOD II

THE BATTERY SHIPPED IN DISCHARGED AND EMPTY CONDITION

Do not remove the transport seal (red plastic film), from the vent cap until ready to fillthe battery. Remove the transit cap (blue/red).

The battery electrolyte is supplied in either dry or liquid form. Dry electrolyte issupplied in the separately sealed packages containing potassium hydroxide andlithium hydroxide. Liquid electrolyte (a mixture of potassium hydroxide, lithium

hydroxide and DM/DI water in the required proportions) is supplied in sealed jerrycans or drums.

Do not open the sealed packages or containers until ready to mix the electrolyte or fillthe battery.

Read the instructions for electrolyte preparation / or filling as required. Also removethe transit cap (blue/red), wherever mounted on cell terminals for big size cells.


7/28

6

5.0 STORAGE

5.1 STORAGE OF NEW BATTERY IN FILLED AND CHARGED CONDITION

A filled and charged battery can be stored for a maximum period of one year.

Store the battery in a clean, dry and cool location. Cover the battery with a sheet ofplastic or similar protective cover to keep out water and shield against direct sunlight.

Do not store other material on top of the battery.

After removing from storage, the battery should be discharged to an average cellvoltage of 1.0 volt at 0.2 C5 Amps, and charged as per the instructions for firstcharging.

5.2 STORAGE OF NEW BATTERY IN DRY & DISCHARGED CONDITION

A dry and discharged battery can be stored for prolonged periods, around ten years.

Store the battery in a clean, dry and cool location. Cover the battery with a sheet ofplastic or similar protective cover to keep out water and shield against direct sunlight.

Do not remove the plastic film sealing the flip top vent.

Do not store other material on top up of the battery.

After removing from storage, follow the instructions for electrolyte filing and firstcharging.

5.3 STORAGE OF USED BATTERY IN FILLED & CHARGED CONDITION

If the battery is going to be left idle for a long period of time, but not more than oneyear, it should be removed from service and properly stored.

Top up with DM/DI water to the maximum level mark and charge the battery to a fullycharging state.

Clean the battery thoroughly, and then coat the inter-cell and inter-crate connectorswith anti-corrosion oil.

Inter-crate connectors should be removed for cleaning, and then stored in a separatepackage.

Store the battery in a clean dry, and cool location. Cover the battery with a sheet ofplastic or similar protective cover to keep out water and shield against direct sunlight.

Do not store other material on top up of the battery.

After removing from storage, the battery should be discharged to an average cellvoltage of 1.0 volt at 0.2 C5 Amps, and charged as per the instructions for firstcharging. However, use only DM/DI water for adjusting the electrolyte level afterwaiting for at least two hours after the first charge has been completed.


8/28

7

5.4 STORAGE OF USED BATTERY IN DRY & DISCHARGED CONDITION

If the storage period is to exceed one year, the batteries should be fully dischargedat 0.2 C5Amps, to an end voltage 0.6 volts per cell, and the electrolyte fully drainedby inverting the batteries for about 5 minutes. Use a plastic film to seal the flip topvent.

Clean the battery thoroughly, and then coat the inter-cell and inter-crate connectors

with anti-corrosion oil.

Inter-crate connectors should be removed for cleaning, and then stored in aseparate package.

Store the battery in a clean, dry and cool location. Cover the battery with a sheet ofplastic or similar protective cover to keep out water and shield against directsunlight.

Do not store other material on top of the battery.

Store the electrolyte in clean, airtight plastic containers for future use. Afterremoving the battery from storage, follow the instructions for electrolyte filling, firstcharging and installing the battery.


9/28

8

6.0 INSTALLATION

The battery should be installed in a clean and dry area.

The battery should never be placed direct on the floor where it is subject todampness and dirt accumulation.

Batteries do not give off corrosive gas and therefore can be installed together with

other electrical equipment.To avoid accelerated ageing of the plastic due to ultra violet radiation, batteries usingplastic cell containers and lids should not be exposed to direct sun light for longperiods.

6.1 TEMPERATURE

Avoid placing the battery in a hot place or in front of a window.

The battery will give the best performance and maximum service life when working ata temperature between 10 and 30 degrees centigrade.

With adequate electrolyte specific gravity, the battery will perform properly within thetemperature range 40 to + 50 degrees centigrade.

Freezing will not cause damage to the battery.

6.2 VENTILATION

During the last part of high-rate charging, the battery gives off gas(Oxygen-hydrogen mixture)

At normal float-charge the gas evolution is very small.

The ventilation requirement of the battery as per DIN 57510 can be expressed by the

relation:

Q=55 x N x I, where Q is the quantity of air to be replaced from battery room inLiters /hour.

N is the number of cells in the battery, and I is the charging current at the end of highrate charging.

Normally, no extra means of ventilation (exhaust fan etc.) is needed unless thebattery room is extremely small in proportion to the size of the battery.

6.3 MOUNTING AND CONNECTIONS

HBL battery racks are recommended for proper installation.

These racks are made of steel components, which are protected with alkali-resistantpaint. The step construction of the racks permit visual electrolyte level checks to bemade on all cells and greatly facilitates the maintenance activity of topping up withdemineralized water.

Battery racks are available in 2,3, or 4 steps in one or two tier configurations. Rackscan be positioned alongside each other or back to back to suit the available space inthe battery location. Ensure that the floor is level while positioning the racks.


10/28

9

All racks are supplied with insulators. However, the racks also have provision fordirect bolting to the floor.

Assemble the racks with the help of the drawing, enclosed with this manual.

Position the cells on the rack suitably so as to permit connection of the positive andnegative terminals according to the wiring diagram.

FOLLOW THE POLARITY TO AVOID SHORT CIRCUITING OF THE CELLS.

Connect the battery terminals to the equipment only after marking all the other inter-cell and inter-row connections

ONLY NICKEL PLATED COPPER CABLE LUGS SHOULD BE USED.

NEVER USE ALUMINUM CABLES AT THE BATTERY TERMINALS.

Use the correct torque to tighten the terminal bolts as indicated below:

BOLT DIAMETER RECOMMENDED TORQUE

M 5 7.5 Nm (0.75 kgfm)

M 8 20 Nm (2.0 kgfm)

M 10 30 Nm (3.0 kgfm)

Ensure correct torque by using an appropriate torque wrench.

Improper torque will affect battery performance.

It is important that the battery is mounted firmly.

When there is a risk of crate movement as in the case of mobile applications, usewooden or plastic wedges for arresting the movement.


11/28

10

7.0 ELECTROLYTE PREPARATION FOR FIRST FILLING

Please read and follow the safety precautions carefully.

The quantity of Electrolyte (if supplied in liquid form) per cell is given in the technicalspecification.

The quantities of solid lithium hydroxide and solid potassium hydroxide required foreach battery if supplied in dry & discharged condition are given in technicalspecification sheet. Amount of lithium hydroxide is depending upon the capacity of thecell. Use this data as proportions for preparing the electrolyte.

Type B electrolyte is a solution Lithium hydroxide crystals and potassium hydroxideflakes in DM/DI water. The number following the B represents the quantity of lithiumhydroxide in grams (assuming 100% assay) per liter of electrolyte.

The required quantity of DM/DI. Water is first into the container and appropriatequantity of lithium hydroxide crystals is added with constant stirring. When all the

lithium hydroxide has dissolved, potassium hydroxide flakes are slowly added withconstant stirring. The solution will become hot.

After cooling to room temperature, adjust the density as required within a tolerance of+/- 0.01 adding D.M water.

7.1 APPARATUS

Use only clean vessels of plastic or steel for preparing the electrolyte. Copper,aluminum or galvanized vessels must not be used. Do not use accessories alreadyused for lead acid batteries. Transfer the electrolyte in to the cells using a clean plasticjug. The electrolyte must not be exposed to air for long periods. Ensure that the

electrolyte does not get contaminated.

7.2 GUARANTEE CONDITIONS

Use only electrolyte approved by HBL Power Systems Limited, for our Ni-Cd batteries.


12/28

11

8.0 ELECTROLYTE FILLING

Flip open the top of the vent or unscrew the cap in case of screw type vent cap andremove the transport seal (plastic film) if you have not already done so.

Do not completely remove the vent for filling the cells, but only flip open the top of fliptop vent cap & unscrew the cap in screw type vent cap for easy access. Only specialspill proof vents like SUNICA vents require to be fully removed for electrolyte filling

and topping up.

Use the correct electrolyte as specified In the Technical Specifications and fill thecells slowly until the level of electrolyte is about 15 mm below the maximum levelindication.

Check the cells after 30 minutes and add electrolyte upto max. level indication.

Check the Technical Specifications for correct levels of electrolyte before filling. Thisis required for cells in stainless steel containers, since these containers are notprovided with the level indication stickers as in the case of cells in polypropylenecontainers. Use the capillary tube provided for checking the electrolyte level in cellswith stainless steel containers.

The specific gravity of the B-22 electrolyte in the cell will now stabilize at 1.19 +/- 0.01from the initial filling electrolyte with specific gravity 1.20 +/- 0.01.

For Special cells (for solar applications), the specific gravity of the B-30 electrolyte inthe cell will now stabilize at 1.26 +/- 0.01 from the initial filling electrolyte with specificgravity 1.28 +/- 0.01.

Using fibre plate batteries, the electrolyte will retain its effectiveness for the life of the

battery.


13/28

12

9.0 CHARGING

The battery can be charged by all normal constant current and constant voltagemethods.

Batteries in parallel operation with charger and load are generally charged withconstant voltage.

In operations where the battery is charged separated from the load, charging witheither constant current or constant voltage can be carried out.

9.1 FIRST CHARGING (DURING COMMISSIONING)

The cell vent caps should be closed during charging. Ensure that the transport sealstrip used for preventing electrolyte spillage during transportation has been removedbefore charging. Also ensure that the transit caps (blue / red), wherever mounted oncell terminals for big size cells.

First charging should be done using constant current only.

Charge the battery with the current recommended in the Technical specifications.

The duration of charge should be such that a charge input of 160% of C5 AH is given.If the charger maximum voltage setting is too low to supply constant current charging,divide the battery into two parts to be charged individually.

The charger must be able to work continuously at current limit without beingdamaged. HBL chargers can do this.

A generous first charge with 160% charge input is important for obtaining maximumbattery performance. The maximum allowable ripple content in the charger outputvoltage should not exceed 5 %.

Add electrolyte after waiting for a period of at least two hours after the first chargehas been completed.

At the same time, check the electrolyte density and adjust if necessary within thespecified limits.

After this final adjustment, the quantity of electrolyte in the battery is correct and

battery is ready for service.

Electrolyte should not be added later. For normal topping up, only DM/DI watershould be used.

THE ELECTROLYTE DENSITY IS NOT AFFECTED BY THE STATE OF CHARGEOF THE BATTERY.


14/28

13

9.2.0 ROUTINE CHARGING (DURING USAGE)

During regular usage the charging method and parameters are to be determined bycharger, load and battery to ensure the system compatibility.

9.2.1 SEPARATE CHARGINGWhen the battery is being charged separate from its load, we recommend 0.2 C ratecharging for 8 hrs with a current 0.2C5 Amps to recharge a fully discharged battery tofull state of charge.

A lower charging current can be applied for a proportionally longer time, however thecurrent should not be less than 0.1C5 A for X & H cells, and 0.05C5 A for M and Lcells.

Constant voltage charging can be used but it requires longer recharge time. Thecharging parameters are as per high rate charging under clause 9.2.3

9.2.2 PARALLEL OPERATION

For continuous parallel operation with occasional battery discharge, use a float-charging voltage in the range of 1.40 to 1.42 volts per cell.

9.2.3 HIGH RATE CHARGING

For recuperative charging of the battery after a discharge, adjust the charging volt-ages to a level corresponding to:

1-52 1.57V/Cell for X cells

1-53 1.67V/Cell for H cells

1.54 1.69 V/Cell for M cells and

1.55 1.70 / Cell for L cells

Charging current limit should be within 0.1 to 0.2 C5

9.2.4 OVER CHARGING

Over charging within reasonable limits will not damage the battery, but waterconsumption will be increased.

9.2.5 UNDER CHARGING

A Ni-Cd battery can be left standing for short periods at any state of charge withoutdamage. But continuous undercharging combined with deep discharging will affectthe battery life.

Note: If the battery is continuously on float charge, it is recommended to boost chargeonce in every 6 months to make sure that the state of charge is at top. The boostcharging should be for such time till there is no change in consecutive readings of15 minutes duration of cell voltages and which will be approximately 4-5 hoursminimum.


15/28

14

10.0 MAINTENANCE

10.1 CLEANLINESS

It is important to keep the battery dry and clean. This will contribute to top theperformance and maximum service life and non-contamination of cells during toppingup.

If potassium carbonate crystals (grey white deposits) form on top of the battery, rubwith a soft brush and wipe with a clean damp cloth followed by a clean dry cloth.

Do not use a wire brush or solvents of any kind, such as gasoline, thinner, acetone,kerosene etc.,

10.2 VENT CAPS

Vent caps should be kept clean to avoid blocking of holes and prevent venting ofgases produced during charging.

Vent caps can be removed from the cells, rinsed in clean water, dried and replaced,vent caps can also be cleaned by wiping with a clean damp cloth followed by a clean

dry cloth while mounting on the cells.

10.3 CONNECTORS

Check at least once a year that all connectors are tight. This is especially important ifthe battery is subjected to vibration or shocks during service.

The connectors and terminal screws should be corrosion protected by coating with athin layer of anti-corrosion oil / petroleum jelly.

10.4 TOPPING UP

The electrolyte level should be always-within the maximum and minimum level marksby replenishing the water.

Use only DM/DI water for toping up.

It is not necessary to add water frequently in an attempt to keep the electrolyte atmaximum level.

Never let the level fall below the top of the plates.

Do not add water to the maximum level during high rate charge since accurate levelreading is not possible when the battery is gassing.

Avoid splashing water when topping up. A wet battery can result in earth faults and/or erratic operation.

Always keep the flame arresting vents closed except for the moment of topping up.

10.5 NEVER USE SULPHRIC ACID

Sulphuric acid will ruin the alkaline battery.

Filling bottles, hydrometers etc., used with lead acid batteries must never be usedwith alkaline batteries in order to prevent acid contamination.


16/28

15

10.6 SPECIFIC GRAVITY

The electrolyte specific gravity should be 1.18 to 1.20.

The specific gravity is not influenced by the state of charge, but increases slightlywhen the electrolyte level is lowered due to water loss.

Electrolyte specific gravity should not be measured immediately after water has beenadded.

10.7 CHECKING THE CHARGING

In parallel operation it is great importance that the recommended charging voltage is keptunchanged. The charger should be checked at least once a year.

A high float voltage setting of the charger, which gives higher current than required duringfloat operation, usually causes high water consumption of the battery.

10.8 TROUBLE SHOOTING

Even though HBL Power Systems Limited nickel cadmium batteries themselves arevery reliable and trouble free, they are part of a larger system that can introduceabnormal conditions, and batteries are also exposed to different quality ofmaintenance.

The following list of possible problems, causes and action will be of good use.

S.No. SYMPTOM PROBABLE CAUSE RECOMMENDED CORRECTIVEACTION

01. Erratic chargerbehaviour

Wrong polarity of cell,block, row of battery.

Check each cell or block for correctpolarity.

Interruption atconnector

Check that no connector or cable ismissing and that all connections aretight and cables securely fastened incable lugs.

Interruption due toempty cell

Check if the cell is empty because ofleakage. If so, remove or short circuitthe cell and use the battery with onecell less, until replacement is made. Ifthe cell is part of the block, do notremove the block, just short circuit thecell.

If the battery is filled with electrolyteon site it could be that one cell hasbeen forgotten. If so, disconnect thecell and fill it with electrolyte.

Faulty charger See charger instructions fortroubleshooting.


17/28

16


02. Earth faultindication

Small leak or leaks Check for wetness on battery stand,or with a voltmeter, area of the batteryhaving the lowest potential to ground.See (1) for procedure if a cell isleaking.

Battery wet due tooverfilling

Disconnect few connectors to avoidhigh or over boiling voltage and cleanthe battery. See (8).

Other equipment ofsystem

Isolate various parts of the DC systemto find the fault.

03. Continuousheavy gassing

Charging voltage isabove therecommended floatvoltage.

See charger instructions forinformation on charging mode andsettings.

04. No power orcapacity at all

Interruption atconnector

See SL.No: 1.

Interruption due toempty cell

See SL.No: 1.

Battery completelydischarged.

Determine why the battery isdischarged. The reason could befaulty charger or fuse, wrong floatvoltage or interruption in the battery.Recharge the battery according toinstructions.

05. Too shortdischarge time.The voltagedecreasesquickly at the

end.

Too larger load. The load may be larger that what thebattery was intended for. Check thedischarge against batteryperformance data. Note that the ratednumber of ampere hours can only be

delivered at discharges, of 5 hours orlonger. For short discharges,batteries will give higher currents butless ampere-hour.

Insufficient charging. Determine why the battery is notcharged to a correct level. Thereason could be low float voltage, nohigh-rate recharge after previousheavy discharge, too short high-raterecharge, of high-rate recharge tovoltage that is too low. Recharge thebattery as per instructions anddischarge again.

Too low batterycapacity.

If the same result is achieved after fulland complete charging, the batterycapacity is low. It may still be able towork its application, especially if it ishigh-rate discharges such as inswitchgear operation or enginestarting. The reason for low capacitycould be age, heavy use, insufficientcharging or unsuitable storage.


18/28

17


06. Low dischargevoltage during amajor part ofdischarge.

Very low voltage forone or few cells.

Check the individual cell voltages duringdischarge and full recharge. If thevoltage of an individual cell does notcome up nearly as high discharge. Asothers, the cells have a partial short

circuit and therefore not acceptingcharge. (If the charging voltage is finebut the cell voltage collapses early inthe discharge the cell capacity isabnormally low). The reason could beunsuitable handling at installation orcontamination in the electrolyte.

Battery designed withhigh cell end voltage.The dischargepreceded by long termfloat charge withoutdischarge.

This condition sometimes occurs if thedesign cell end voltage is 1.14 1.18volt per cell and the battery has been inservice for sometime. It does not meanthat the capacity has decreased. It isbest handled by using more cells in thebattery and thus lowering the final cellvoltages, and high rate or boostcharging now and then.

07 Too low forengine starting.The engine doesnot turn at all, orwith too lowspeed to fire

Discharged batterydue to insufficientcharging

Insufficient charging, See (06)

Loose connector Tighten all connectors. For high powerdischarges this is very important, bothfrom a performance and safety

viewpoint. A loose connector will causevoltage drops and can spark and ignitecharging gasses.

Too low temperature If the temperature is lower than thedesign temperature for the startingsystem, it will be difficult to startbecause the battery gives less powerwhereas the engine requires morepower to turn. Use the correct engine oilfor the temperature and try to arrangepreheating of the engine and battery ifpossible.

Engine trouble If cranking speed appears to be good,

failure to start may depend on the fuelor engine. The battery cannot do morethan crank engine at sufficient speed.

08 Wet battery Overfilling or overboiling

Disconnect a few connectors to avoidhigh voltage and clean the battery. Useproper filling equipment to avoidoverfilling. Over boiling is the result oftoo high electrolyte level and high ratecharging. Normal level and charging attoo high rate may also cause overboiling.


19/28

18


Sudden eruption ofelectrolyte from onecell

Disconnect a few connectors to avoidhigh voltage and clean the battery. Fillthe electrolyte or DM/DI water in thecell, which has lost the electrolyte andcharge the cell individually. Then

replace the cell in the battery andrecharge the complete battery. Checkthe individual cell voltages.

If one cell in a battery with highcurrent load such as engine starting iscompletely discharged it may spewout electrolyte when the high currentis applied.

Electrolyte leakage atposts and vents.

After sometime in service, electrolytemay penetrate the seals around theposts, vents and connectors. In thenormal cleaning of the battery, it doesnot affect the performance of thebattery to any extent.

Electrolyte leakagethrough pores orcracks.

A leakage through a pore or smallcrack could be so small that it doesnot affect the electrolyte levelnoticeably, but will cause earth faultsand the cell or block should bereplaced.

09 Unevenelectrolyte levelsin the battery

Poor filling or toppingup.

If the levels of electrolyte varythroughout the battery, the reason isprobably poor topping up or leveling

off after filling.

Different float voltages Batteries are often divided in twohalves, which is good from reliabilityand maintenance viewpoints. If eachhalf has a separate charger and thevoltage is different, the electrolytelevels in the two halves will bedifferent

Leaking cell If one cell has a lower electrolyte levelthan all the others, it is probablyleaking. The leak could be small and

difficult to find, but the battery stand isprobably wet from electrolyte underthe cell. One individual cell could notconsume more water than the othersas the same current goes through allcells.

Short circuit in onecell

A cell with partial or complete shortcircuit will consume less water thanthe others. Let the cell remain untilreplacement is arranged.


20/28

19

11.0 DOS AND DO NOTS

11.1 DOS

1. Keep the battery always dry and clean. This will prevent leakage of current andprotect the nickel-plating on the external battery components.

2. Check inter-cell connectors for proper tightness. This will prevent heatgeneration at the point of loose contact, which causes damage to thecomponents and can be a fire hazard. Loose contact can also cause batteryfailure due to creation of an open circuit.

3. Ensure that the cell connections have been made as per the wiring diagramprovided. Normally Red washer on cell terminal indicates positive polarity andblue washer indicates negative polarity.

4. Ensure that the battery cable lugs are electro plated. This will prevent thecopper from reacting with the electrolyte.

5. Ensure that the transport seal (plastic strip in vent cap) is removed beforecharging. This will permit escape of the oxygen and hydrogen gases generatedduring charging.

6. Keep vent caps always closed during charging and discharging. This willprevent the carbon dioxide from the air from combining with the alkalineelectrolyte and producing potassium carbonate, thereby reducing the electricalconductivity of the electrolyte.

7. Check the electrolyte level and ensure that it does not fall below the minimumlevel, which is indicated, on the cell-marking label. This active materialcontained in the portion of the plates, which are exposed above the Electrolyte,

will be permanently damaged if the battery remains in service.

8. Use only DM/DI water to top up the cells. (During initial Commissioning useonly electrolyte to make up for loss of electrolyte during transportation). OnlyDM/DI water is to be used to compensate for the loss of water during charging,and maintain the required electrolyte level and specific gravity.

9. Ensure proper functioning of charger and proper connections to the battery.Correct voltage and current settings are important for keeping the battery incharged, ready to use condition.

10. Use insulated tools while working on the battery to prevent accidental shortcircuit and consequent damage.

11. Use alkaline electrolyte only since this is an alkaline battery.


21/28

20

11.2 DO NOTS

1. Do not use apparatus, like hydrometers, capillary tubes, and thermometersetc., used in lead acid batteries in order to prevent contamination of electrolyte.

2. Do not use petrol, kerosene, or any strong chemicals for cleaning batteries.

3. Do not use wire or any hard brush to clean deposits on the intercell connectorsand terminals since this will damage the nickel plating.

4. Do not use aluminum cables for making connections to the battery terminalssince aluminum reacts with the alkaline electrolyte.

5. Do not keep vent caps open and expose electrolyte to air, since this will causesome of the electrolyte to be converted to potassium carbonate and therebyreduce the conductivity of the electrolyte.

6. Do not spill water or electrolyte on and around the battery since this will createconductive paths leading to leakage of current.

7. Do not measure specific gravity immediately after adding DM/DI water sincethis will indicate a lower specific gravity due to inadequate mixing of the waterwith electrolyte in the cell. Specific gravity can be measured after one hour.

8. Do not install the Battery in places where it is exposed to sunlight, since thiswill cause accelerated ageing of plastic components due to ultra violetradiation.

9. Do not remove vent caps (in case of flip type vent caps) for topping up sincefrequent removal can damage the vent cap and the cell lid. In case of flip typevent caps, gently press the cap to open the spring loaded vent lid and in caseof threaded type vent cap, gently unscrew the vent cap lid.

10. Do not use acid since the battery requires alkaline electrolyte. Addition of acidwill cause it to react with the alkaline electrolyte, and cause permanent batterydamage.

11. Do not charge the battery without removing the transport seal from the vent, orwhile the battery is covered, since it is important to ventilate the battery andpermit the gases produced towards the end of charge to escape.

12. Do not adjust terminal connections during usage to prevent sparking whichcan ignite the oxygen and hydrogen gases which are given off by the batterytowards completion of charge, and cause a fire / explosion.

13. Do not smoke in the battery room since it is a fire hazard.

14. Do not keep Batteries in the same room where acid batteries are kept.


22/28

21

11.3 DISPOSAL OF USED BATTERIES

Nickel cadmium batteries must not be discarded as harmless waste and should betreated carefully in accordance with local and national regulations.

Contact HBL for disposal and recycling assistance. More than 99% of battery metals canbe recycled.

12.0 DM / DI WATER SPECIFICATION

12.1 PERMITTED IMPURITIES IN WATER

IMPURITY CALCULATED AS TOPPING UPWATER MAXIMUM

g/l

WATER FORPREPARATION OF

ELECTROYTEMAXIMUM g/l

Chloride KCl Traces 0.06

Sulphate K2SO4 Traces 0.05

Nitrate KNO3 Traces Traces

Silico SiO2 Traces Traces

Aluminium Al2O3 Traces Traces

Calcium &Magnesium

CaO+MgO Traces Traces

Heavy Metals Traces 0.03

Organicimpurities

KMNO4 0.03 0.06

Note : Topping up must be with DM/DI water with the conductivity less than 10 microsiemens /cm


23/28

22

13.0 SERVICE LOG

Date of installation and commissioning: _________________________________

Battery No.: ___________________________

Date : _______________________________

CELL NOS DISCREPANCIES NOTICED CORRECTIVE ACTIONS / REMARKS


24/28

23

Service Log (Continue)

Date: _________________________

CELL NOS DISCREPANCIES NOTICED CORRECTIVE ACTIONS / REMARKS


25/28

24

14.0 TOOLS & ACCESSORIES


26/28

25

15.0 DRAWINGS


27/28

26

16.0 TEST CERTIFICATE


28/28

HBL POWER SYSTEMS LIMITED

FACTORY REGD. OFFICE

ALIABAD VILLAGE 8-2-601, ROAD NO. 10, BANJARA HILLSSHAMEERPET MANDAL HYDERABAD 500034, A.P., INDIA

HYDERABAD 500 078 TEL : 91-402335 5575 / 2335 5147

TEL : 08418 244640 to 49 FAX : 91-40-2335 3189FAX : 08418 244574 / 244627

REGIONAL OFFICES

HYDERABAD CALCUTTA

SHAMEERPET MANDAL BD-79 ( GROUND FLOOR )

HYDERABAD 500 078 SECTOR 1, SALT LAKE CITY,

TEL : 08418 244640 to 49 TEL : +91-33-2359 9174FAX : 08418 244574 / 244627 FAX : +91-33-2359 9173

MUMBAI CHENNAI

NO-29, MAHAVEER CENTRE, PLOT NO. : 3055, 5th

STREET

2nd

FLOOR, SECTOR -17 NEHRU NAGAR, 13th

MAIN ROAD

VASHI, NAVI MUMBAI 703 ANNA NAGAR, CHENNAI 600 040TEL : +91-22-2789 3498 TEL : +91-44-620 0073

FAX : +91-22-2789 3512 FAX : +91-44-626 1329

NEW DELHI BANGALOREB-52, SECTOR-14, NO. 44 , CENTRAL STREET,NOIDA, SIVAJI NAGAR,

U.P. 201 301 BANGALORE 560 001

TEL : +91-120-2432734 TEL : +91-80-51130303

FAX : +91-120-2432738 FAX : +91-80-51130306

Visit us at : www.hbl.in

Documents

Fibre Plate _O & M