Ficha Tecnica de Mobilarma 798 Copy

5/19/2018 Ficha Tecnica de Mobilarma 798 Copy

1/14

Due to continual product research and development, the information contained herein is subject to change without notification.Typical properties may vary slightly. Additional health and safety information on this product can be found on the Material Safety Data Sheet, which is available on line atwww.imperialoil.ca, or by contacting Lubricants and Petroleum Specialties, Technical Help Desk, 1-800-268-3183. 2003 Imperial Oil.

Wire Rope Rust Protective and Lubricant

Product Description

Mobilarma 798 is premium performance, oil-based rust preventive intended to serve as a wire rope lubricant and to prevent rust andcorrosion under application and storage conditions. It is used in industrial, mining, and marine applications. Mobilarma 798 hasexcellent film forming properties and is of grease-like consistency. Its tenacious film protects wire ropes from the corrosive tendenciesof salt spray and moisture-laden atmospheres. Mobilarma 798 is effective throughout the extremes of temperatures that may be

encountered at sea and gives good protection against mild acids. It is pliable at 35C and will not drip at 60 C. It resists throw-off inhigh-speed service and adheres without being tacky or stringy. On application, Mobilarma 798 becomes transparent; enabling treatedropes to be visually inspected. The film is self-healing and does not chip.

Mobilarma 798 works well between the strands of wire rope, providing excellent lubrication during flexing. This characteristic reduceswear and improves life. It is compatible with other wire rope core impregnating materials that may have been applied duringmanufacture.

Features & Benefits

Mobilarma 798 works well between the strands of wire rope, providing excellent lubrication during flexing. This characteristic reduceswear and helps improve life. It is compatible with other wire rope core impregnating materials that may have been applied duringmanufacture. Its excellent rust and corrosion protection properties substantially reduce the negative effects of fresh water, salt waterand mild acids thus improving performance and reducing maintenance costs. It is easy to apply and economical to use.

Features Advantages and Potential Benefits

Outstanding Adhesive Characteristics Resists throw-off Forms transparent film making rope inspection easier

Excellent Rust and Corrosion Protection Provides protection against rusting from both fresh water and saltwater over a wide temperature rangeProtects rope against attack from mild acids

Very Good Lubrication Properties Reduces wear Improved efficiency

Easy Application Can be applied by brushed or swab as receivedCan be applied by spray, dip or bath if heated

Applications

Mobilarma 798 can either be applied as received by brush or swab, or by spray, dip or bath if the product is first heated to 65oC or

higher. For best results, only a thin coat should be applied. New cables or cables regularly maintained with Mobilarma 798 will requireno prior preparation. For best results, rusty or dirty wire ropes should be wire brushed and cleaned thoroughly with solvent and driedprior to application of Mobilarma 798.

Lubrication and preservation of standing and running ropes in both industrial, mining, and marine applications

Impregnation of steel wire ropes during manufacture


2/14

Due to continual product research and development, the information contained herein is subject to change without notification.Typical properties may vary slightly. Additional health and safety information on this product can be found on the Material Safety Data Sheet, which is available on line atwww.imperialoil.ca, or by contacting Lubricants and Petroleum Specialties, Technical Help Desk, 1-800-268-3183. 2003 Imperial Oil.

Typical PropertiesMobilarma 798

Viscosity, ASTM D 445, cSt @ 100C 23.1

Dropping Point, ASTM D 2265, C, min 63

Flash Point, C, ASTM D 92, min 238

Density @ 15.6C, Calculated, lbs/gal 7.36

Precautions

Mobilarma 798is manufactured from high quality petroleum base stocks , carefully blended with selected additives. As with allpetroleum products, good personal hygiene and careful handling should always be practiced. Avoid prolonged contact to skin,splashing into the eyes, ingestion or vapour inhalation. Please refer to our Imperial Oil Material Safety Data Sheet for further

information.

Note: This product is not controlled under Canadian WHMIS legislation.

The Mobil logotype and the Pegasus design are trademarks of Exxon Mobil Corporation, or one of its subsidiaries.


3/14

Mobilarma 700 Series

Premium Performance Rust Preventives

Product Description

The Mobilarma 700 Series contains three premium performance rust preventives that cover a range of applications

including storage and inter-operational activities. The Mobilarma 777 and 778 are intended for protection cold-rolled sheet

and coiled steel in the metal industry. Mobilarma 798 is intended for the lubrication and rust protection of wire rope in

industrial, construction, mining and marine applications. The Mobilarma 700 Series products exhibit excellent water

displacing properties and form thin tenacious films that protect surfaces even under severe conditions that include high

moisture levels and exposure to acid or corrosive fumes.

The Mobilarma 777 and 778 form wet, oily and extremely thin barrier films that are not tacky so that they will not attract dirt

or other foreign matter. They will protect sheet and coiled steel for up to twelve months, even under severe conditions that

include variations in humidity and exposure to acid fumes that might be found in the vicinity of pickling operations.

Mobilarma 798 forms a grease-like film that protects wire ropes from corrosion tendencies of salt spray and moisture-

laden atmospheres. It is effective throughout the extremes of temperature that may be encountered at sea and gives good

protection against mild acids. It is pliable at 35oC and will not drip at 60oC. It resists throw-off in high-speed service and

adheres without being tacky or stringy. The film is self-healing and does not chip.

Features and Benefits

Mobilarma 777 and 778 provide an effective and cost efficient means of protecting cold-rolled sheet and coiled steel prior

to processing and during storage. They provide extended protection, even under severe storage conditions resulting in less

reject and scrapped materials.

Mobilarma 798 works well between the strands of wire rope providing excellent lubrication as well as protective films.

These characteristics reduce wear and improve life of the wire ropes as well as minimize maintenance costs associated

with their use. It is compatible with other wire rope core impregnating materials that may have been applied during

manufacture. It is easy to apply and economical to use.

Applications

Mobilarma 777 and 778 are recommended for use as:

- Protective coatings for cold-rolled sheet and coiled steel

- Coatings for precision machined parts and instruments for storage

- A die lubricant (Mobilarma 778) in some light duty pressing operation

Mobilarma 798 is recommended for use for:

- Lubrication and preservation of strands and running ropes- Impregnation of steel wire ropes during manufacture

Effective rust and corrosion protection Less waste and lower costs

Easy application Less waste and lower costs

Economical to use Good coverage and protection with thin films

Features Advantages and Potential Benefits

Page 1 of 2Mobilarma 700 Series

18/10/2012http://www.mobil.com/Singapore-English/Lubes/PDS/GLXXENINDMOMobilarma ...


4/14

p g p g _

Typical Properties

Health and Safety

Based on available information, this product is not expected to produce adverse effects on health when used for the

intended application and the recommendations provided in the Material Safety Data Sheet (MSDS) are followed. MSDS's

are available upon request through your sales contract office, or via the Internet. This product should not be used for

purposes other than its intended use. If disposing of used product, take care to protect the environment.

The Mobil logotype, the Pegasus design, and Mobilarma are trademarks of Exxon Mobil Corporation, or one of its

subsidiaries.

ExxonMobil Asia Pacific Ltd

1 HarbourFront Place

#06-00 HarbourFront Tower One

Singapore 098633

+65 6885 8000

http://www.exxonmobil.com

Typical Properties are typical of those obtained with normal production tolerance and do not constitute a specification.

Variations that do not affect product performance are to be expected during normal manufacture and at different blending

locations. The information contained herein is subject to change without notice. All products may not be available locally.

For more information, contact your local ExxonMobil contact or visitwww.exxonmobil.com

ExxonMobil is comprised of numerous affiliates and subsidiaries, many with names that include Esso, Mobil, or

ExxonMobil. Nothing in this document is intended to override or supersede the corporate separateness of local entities.

Responsibility for local action and accountability remains with the local ExxonMobil-affiliate entities.

Copyright 2001-2012 Exxon Mobil Corporation. All rights reserved..

Viscosity, ASTM D 445

cSt @ 40C 13 21

cSt @ 100C 23.1

Dropping point, ASTM D 2265, oC 63

Pour Point, C, ASTM D 97 -6 -3

Flash Point, C, ASTM D 92 120 190 238

Density @15.6 C, calculated, lbs/gal 7.36

Specific gravity, ASTM D 1298 0.860 0.880

Mobilarma 700 Series 777 778 798

Page 2 of 2Mobilarma 700 Series

18/10/2012http://www.mobil.com/Singapore-English/Lubes/PDS/GLXXENINDMOMobilarma ...


5/14

p g p g _

Product Name: MOBILARMA 798Revision Date: 19 Sep 2011

Page 1 of 10

______________________________________________________________________________________________________________________

SAFETY DATA SHEET

SECTION 1 PRODUCT AND COMPANY IDENTIFICATION

As of the revision date above, this (M)SDS meets the regulations in the United Kingdom & Ireland.

PRODUCTProduct Name: MOBILARMA 798Product Description: Base Oil and AdditivesProduct Code: 201570401055, 400507, 667212-60Intended Use: Corrosion inhibitor

COMPANY IDENTIFICATIONSupplier: EXXONMOBIL MARINE LIMITED

EXXONMOBIL HOUSEMAILPOINT 31, ERMYN WAYKT22 8UX LEATHERHEADUnited Kingdom

24 Hour Environmental / Health EmergencyTelephone

+44 (0)23 80891558

Supplier General Contact +44 1372 222 000E-Mail [email protected]

SECTION 2 HAZARDS IDENTIFICATION

This material is not considered to be hazardous according to regulatory guidelines see Section 15.

PHYSICAL / CHEMICAL HAZARDS

Thermal burn hazard - contact with hot material may cause thermal burns.

HEALTH HAZARDS

Low order of toxicity. Excessive exposure may result in eye, skin, or respiratory irritation. High-pressureinjection under skin may cause serious damage. When heated, the vapour/fumes given off may causerespiratory tract irritation.

NOTE: This material should not be used for any other purpose than the intended use in Section 1 without expert

advice. Health studies have shown that chemical exposure may cause potential human health risks which may varyfrom person to person.


6/14


Page 2 of 10

______________________________________________________________________________________________________________________

SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS

No Reportable Hazardous Substance(s) or Complex Substance(s).

SECTION 4 FIRST AID MEASURES

INHALATION

Remove from further exposure. For those providing assistance, avoid exposure to yourself or others. Useadequate respiratory protection. If respiratory irritation, dizziness, nausea, or unconsciousness occurs, seekimmediate medical assistance. If breathing has stopped, assist ventilation with a mechanical device or usemouth-to-mouth resuscitation.

SKIN CONTACT

Wash contact areas with soap and water. Remove contaminated clothing. Launder contaminated clothingbefore reuse. If burned by contact with hot material, molten material adhering to skin should be cooled asquickly as possible with water, and see a physician for removal of adhering material and treatment of burn. Ifproduct is injected into or under the skin, or into any part of the body, regardless of the appearance of thewound or its size, the individual should be evaluated immediately by a physician as a surgical emergency. Eventhough initial symptoms from high pressure injection may be minimal or absent, early surgical treatment withinthe first few hours may significantly reduce the ultimate extent of injury.

EYE CONTACT

Flush thoroughly with water for at least 15 minutes. Get medical assistance.

INGESTION

First aid is normally not required. Seek medical attention if discomfort occurs.

SECTION 5 FIRE FIGHTING MEASURES

EXTINGUISHING MEDIAAppropriate Extinguishing Media: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish

flames.

Inappropriate Extinguishing Media: Straight streams of water

FIRE FIGHTINGFire Fighting Instructions: Evacuate area. Prevent run-off from fire control or dilution from entering streams,

sewers or drinking water supply. Fire-fighters should use standard protective equipment and in enclosedspaces, self-contained breathing apparatus (SCBA). Use water spray to cool fire exposed surfaces and toprotect personnel.

Hazardous Combustion Products: Smoke, Fume, Aldehydes, Sulphur oxides, Incomplete combustionproducts, Wax fumes, Oxides of carbon, Amine


7/14


Page 3 of 10

______________________________________________________________________________________________________________________

FLAMMABILITY PROPERTIESFlash Point [Method]: >210C (410F) [ASTM D-92]Flammable Limits (Approximate volume % in air): LEL: 0.9 UEL: 7.0Autoignition Temperature: N/D

SECTION 6 ACCIDENTAL RELEASE MEASURES

NOTIFICATION PROCEDURES

In the event of a spill or accidental release, notify relevant authorities in accordance with all applicableregulations.

PROTECTIVE MEASURES

Avoid contact with spilled material. See Section 5 for fire fighting information. See the Hazard IdentificationSection for Significant Hazards. See Section 4 for First Aid Advice. See Section 8 for advice on the minimumrequirements for personal protective equipment. Additional protective measures may be necessary, dependingon the specific circumstances and/or the expert judgment of the emergency responders. For emergencyresponders: Respiratory protection: respiratory protection will be necessary only in special cases, e.g.,formation of mists. Half-face or full-face respirator with filter(s) for dust/organic vapor or Self ContainedBreathing Apparatus (SCBA) can be used depending on the size of spill and potential level of exposure. If theexposure cannot be completely characterized or an oxygen deficient atmosphere is possible or anticipated,SCBA is recommended. Work gloves that are resistant to hydrocarbons are recommended. Gloves made ofpolyvinyl acetate (PVA) are not water-resistant and are not suitable for emergency use. Chemical goggles arerecommended if splashes or contact with eyes is possible. Small spills: normal antistatic work clothes areusually adequate. Large spills: full body suit of chemical resistant, antistatic material is recommended.

SPILL MANAGEMENTLand Spill: Stop leak if you can do so without risk. Recover by pumping or with suitable absorbent. If liquid istoo viscous for pumping, shovel it up into a suitable container for recycle or disposal.

Water Spill: Stop leak if you can do so without risk. Confine the spill immediately with booms. Warn other

shipping. Remove from the surface by skimming or with suitable absorbents. Seek the advice of a specialistbefore using dispersants.

Water spill and land spill recommendations are based on the most likely spill scenario for this material;however, geographic conditions, wind, temperature, (and in the case of a water spill) wave and current directionand speed may greatly influence the appropriate action to be taken. For this reason, local experts should beconsulted. Note: Local regulations may prescribe or limit action to be taken.

ENVIRONMENTAL PRECAUTIONS

Large Spills: Dyke far ahead of liquid spill for later recovery and disposal. Prevent entry into waterways,sewers, basements or confined areas.

SECTION 7 HANDLING AND STORAGE

HANDLING

Avoid contact with skin. When heated, the vapour/fumes given off may cause respiratory tract irritation.Prevent small spills and leakage to avoid slip hazard. Material can accumulate static charges which maycause an electrical spark (ignition source). When the material is handled in bulk, an electrical spark could igniteany flammable vapors from liquids or residues that may be present (e.g., during switch-loading operations).


8/14


Page 4 of 10

______________________________________________________________________________________________________________________

Use proper bonding and/or earthing procedures. However, bonding and earthing may not eliminate the hazardfrom static accumulation. Consult local applicable standards for guidance. Additional references include

American Petroleum Institute 2003 (Protection Against Ignitions Arising out of Static, Lightning and StrayCurrents) or National Fire Protection Agency 77 (Recommended Practice on Static Electricity) or CENELECCLC/TR 50404 (Electrostatics - Code of practice for the avoidance of hazards due to static electricity).

Static Accumulator: This material is a static accumulator.

STORAGE

The container choice, for example storage vessel, may effect static accumulation and dissipation. Do not storein open or unlabelled containers.

SPECIFIC END USES: Section 1 informs about identified end-uses. No industrial or sector specific guidance

available.

SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION

EXPOSURE LIMIT VALUES

Exposure limits/standards (Note: Exposure limits are not additive)

Substance Name Form Limit/Standard Note Source

Wax fumes Fume. STEL 6 mg/m3 UK EH40

Wax fumes Fume. TWA 2 mg/m3 UK EH40

Wax fumes Fume. TWA 2 mg/m3 ACGIH

Exposure limits/standards for materials that can be formed when handling this product: When mists/aerosolscan occur the following is recommended: 5 mg/m - ACGIH TLV (inhalable fraction).

Note: Information about recommended monitoring procedures can be obtained from the relevantagency(ies)/institute(s):

UK Health and Safety Executive (HSE)

ENGINEERING CONTROLS

The level of protection and types of controls necessary will vary depending upon potential exposure conditions.Control measures to consider:

Adequate ventilation should be provided so that exposure limits are not exceeded.

PERSONAL PROTECTION

Personal protective equipment selections vary based on potential exposure conditions such as applications,handling practices, concentration and ventilation. Information on the selection of protective equipment for usewith this material, as provided below, is based upon intended, normal usage.


9/14


Page 5 of 10

______________________________________________________________________________________________________________________

Respiratory Protection: If engineering controls do not maintain airborne contaminant concentrations at a

level which is adequate to protect worker health, an approved respirator may be appropriate. Respiratorselection, use, and maintenance must be in accordance with regulatory requirements, if applicable. Types ofrespirators to be considered for this material include:

No special requirements under ordinary conditions of use and with adequate ventilation.

For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode.Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate,gas/vapour warning properties are poor, or if air purifying filter capacity/rating may be exceeded.

Hand Protection: Any specific glove information provided is based on published literature and glove

manufacturer data. Glove suitability and breakthrough time will differ depending on the specific use conditions.

Contact the glove manufacturer for specific advice on glove selection and breakthrough times for your useconditions. Inspect and replace worn or damaged gloves. The types of gloves to be considered for this materialinclude:

Chemical resistant gloves are recommended. If product is hot, thermally protective, chemical resistantgloves are recommended. If contact with forearms is likely, wear gauntlet style gloves. CEN standardsEN 420 and EN 374 provide general requirements and lists of glove types.

Eye Protection: If contact with material may occur, safety glasses and face shield are recommended.

Skin and Body Protection: Any specific clothing information provided is based on published literature ormanufacturer data. The types of clothing to be considered for this material include:

Chemical/oil resistant clothing is recommended. If product is hot, thermally protective, chemicalresistant apron and long sleeves are recommended.

Specific Hygiene Measures: Always observe good personal hygiene measures, such as washing after

handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protectiveequipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned.Practice good housekeeping.

ENVIRONMENTAL CONTROLS

See Sections 6, 7, 12, 13.

SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES

Note: Physical and chemical properties are provided for safety, health and environmental considerations onlyand may not fully represent product specifications. Contact the Supplier for additional information.

GENERAL INFORMATIONPhysical State: LiquidColour: AmberOdour: CharacteristicOdour Threshold: N/D

IMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATION


10/14


Page 6 of 10

______________________________________________________________________________________________________________________

Relative Density (at 15 C): 0.88Flash Point [Method]: >210C (410F) [ASTM D-92]Flammable Limits (Approximate volume % in air): LEL: 0.9 UEL: 7.0Autoignition Temperature: N/DBoiling Point / Range: > 316C (600F) [Estimated]Vapour Density (Air = 1): > 2 at 101 kPa [Estimated]Vapour Pressure: < 0.013 kPa (0.1 mm Hg) at 20 C [Estimated]Evaporation Rate (n-butyl acetate = 1): N/DpH: N/ALog Pow (n-Octanol/Water Partition Coefficient): > 3.5 [Estimated]Solubility in Water: NegligibleViscosity: [N/D at 40C] | 23.2 cSt (23.2 mm2/sec) at 100CExplosive Properties: N/D

Oxidizing Properties: See Hazards Identification Section.

OTHER INFORMATIONFreezing Point: N/DMelting Point: N/ADMSO Extract (mineral oil only), IP-346: < 3 %wtDecomposition Temperature: N/D

SECTION 10 STABILITY AND REACTIVITY

STABILITY: Material is stable under normal conditions.

CONDITIONS TO AVOID: High energy sources of ignition.

MATERIALS TO AVOID: Strong oxidisers

HAZARDOUS DECOMPOSITION PRODUCTS: Material does not decompose at ambient temperatures.

HAZARDOUS POLYMERIZATION: Will not occur.

SECTION 11 TOXICOLOGICAL INFORMATION

ACUTE TOXICITY

Route of Exposure Conclusion / RemarksInhalation

Toxicity: No end point data. Not determined.

Irritation: No end point data. Elevated temperatures or mechanical action may form vapours,mist, or fumes which may be irritating to the eyes, nose, throat, orlungs. Based on assessment of the components.

Ingestion

Toxicity: LD50 > 5000 mg/kg Minimally Toxic. Based on test data for structurally similarmaterials.

Skin

Toxicity: LD50 > 5000 mg/kg Minimally Toxic. Based on test data for structurally similarmaterials.


11/14


Page 7 of 10

______________________________________________________________________________________________________________________

Irritation: Data available. Negligible irritation to skin at ambient temperatures. Based on testdata for structurally similar materials.

Eye

Irritation: Data available. May cause mild, short-lasting discomfort to eyes. Based on testdata for structurally similar materials.

OTHER HEALTH EFFECTS FROM SHORT AND LONG TERM EXPOSURE

Anticipated health effects from sub-chronic, chronic, respiratory or skin sensitization, mutagenicity, reproductive toxicity,carcinogenicity, target organ toxicity (single exposure or repeated exposure), aspiration toxicity and other effects basedon human experience and/or experimental data.

CHRONIC/OTHER EFFECTS

For the product itself:Elevated temperatures or mechanical action may form vapours, mists or fumes which may be irritating to the

eyes and respiratory tract.Contains:Base oil severely refined: Not carcinogenic in animal studies. Representative material passes IP-346, Modified

Ames test, and/or other screening tests. Dermal and inhalation studies showed minimal effects; lung non-specific infiltration of immune cells, oil deposition and minimal granuloma formation. Not sensitising in testanimals.

Additional information is available by request.

SECTION 12 ECOLOGICAL INFORMATION

The information given is based on data available for the material, the components of the material, and similar materials.

ECOTOXICITY

Material -- Not expected to be harmful to aquatic organisms.

MOBILITY

Base oil component -- Low solubility and floats and is expected to migrate from water to the land. Expected topartition to sediment and wastewater solids.

PERSISTENCE AND DEGRADABILITYBiodegradation:

Base oil component -- Expected to be inherently biodegradable

BIOACCUMULATION POTENTIAL

Base oil component -- Has the potential to bioaccumulate, however metabolism or physical properties mayreduce the bioconcentration or limit bioavailability.

SECTION 13 DISPOSAL CONSIDERATIONS


12/14


Page 8 of 10

______________________________________________________________________________________________________________________

Disposal recommendations based on material as supplied. Disposal must be in accordance with current applicablelaws and regulations, and material characteristics at time of disposal.

DISPOSAL RECOMMENDATIONS

Product is suitable for burning in an enclosed controlled burner for fuel value or disposal by supervisedincineration at very high temperatures to prevent formation of undesirable combustion products.

REGULATORY DISPOSAL INFORMATION

European Waste Code: 13 02 05*

NOTE: These codes are assigned based upon the most common uses for this material and may not reflectcontaminants resulting from actual use. Waste producers need to assess the actual process used when

generating the waste and its contaminants in order to assign the proper waste disposal code(s).

This material is considered as hazardous waste pursuant to Directive 91/689/EEC on hazardous waste, andsubject to the provisions of that Directive unless Article 1(5) of that Directive applies.

Empty Container WarningEmpty Container Warning (where applicable): Empty containers may contain residue and

can be dangerous. Do not attempt to refill or clean containers without proper instructions. Empty drums should becompletely drained and safely stored until appropriately reconditioned or disposed. Empty containers should be takenfor recycling, recovery, or disposal through suitably qualified or licensed contractor and in accordance withgovernmental regulations. DO NOT PRESSURISE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSESUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION.THEY MAY EXPLODE AND CAUSE INJURY OR DEATH.

SECTION 14 TRANSPORT INFORMATION

LAND (ADR/RID): Not Regulated for Land Transport

INLAND WATERWAYS (ADNR/ADN): Not Regulated for Inland Waterways Transport

SEA (IMDG): Not Regulated for Sea Transport according to IMDG-Code

AIR (IATA): Not Regulated for Air Transport

SECTION 15 REGULATORY INFORMATION

REACH Information: A Chemical Safety Assessment has not been carried out for the substance(s) that make up thismaterial or for the material itself.

Material is not dangerous as defined by the EU Dangerous Substances/Preparations Directives.

EU LABELING: Not regulated according to EC Directives

.

.


13/14


Page 9 of 10

______________________________________________________________________________________________________________________

Contains: POLYAMINE May produce an allergic reaction. This material contains one or more sensitizers


14/14


Page 10 of 10

______________________________________________________________________________________________________________________

MHC: 0B, 0B, 0, 0, 0, 1 PPEC: AH

DGN: 2010611QGB (1009119)-----------------------------------------------------------------------------------------------------------------------------------------------------

ANNEX

Annex not required for this material.

Documents

Ficha Tecnica de Mobilarma 798 Copy