FILTRATION SYSTEMS FOR

17

F-701R

343SERIES 'DF'FILTRATION SYSTEMS

TYPICAL INSTALLATIONSYSTEM OPERATION

This system is totally automatic and responds to wide variations in flow rate and solids concentration. Pump the contaminated solution to the diffuser tray which distrib-utes flow across the full width of the filter bed. Particle separation starts immediately via gravity flow through the media to the clean reservoir below the conveyor frame. Filtered solution can then gravity drain to waste or be returned to the process via a pump.

Gravity flow allows gentle accumulation and settling of solids on the filter fabric. The concave configuration of the media bed accommodates the flow rate and maximizes solids loading on the fabric. As the media gradually be-comes laden with solids, the solution level will slowly rise until the float switch activates the convey or drive motor. Consumed fabric is advanced to the sludge box as fresh media is simultaneously indexed to the solution flow.

MODEL DF-1.5

MODEL DF-11

AUTOMATIC DISPOSABLE FABRIC FILTRATION SYSTEMS FOR:

PHOSPHATING / PARTS WASHERS MACHINE TOOL COOLANTS INDUSTRIAL WASTE WATER

PROCESS OR COOLING WATER WATER WALL SPRAY BOOTHS

TREATED PLATING WASTE

● Unattended operationAutomatically indexing media allows continuous filtration, even with varying input or solids content.

● Choice of materials Carbon steel, 316 stainless steel, CPVC or polypropylene

● Sizes for any application From 1.5 to 113 sq. ft. of filter surface area

● Low operating cost

17

F-701R

344

SERIES 'DF' FILTRATION SYSTEMS

FABRIC MICRON RATING

CARBON STEEL reservoir, frame, shafts, bearings and sprockets. Models 1.5 to 11 feature a 316 stain-less steel conveyor belt. Larger models have galvanized belt with optional 304 or 316 stainless steel belt. Units are coated with corrosion resistant 2-part epoxy paint.

316 STAINLESS STEEL reservoir, frame, shafts, bearings, sprockets and conveyor belt. Non-wetted surfaces such as fabric bracket, motor bracket and gear reducer are carbon steel.

CPVC frame, polypropylene reservoir, conveyor belt and sprockets, Delrin® bearings, HDPE sludge box. PVC shafts on Model 1.5, 316 stainless steel shafts on Models 4 and larger.

POLYPROPYLENE reservoir, frame, sprockets and conveyor belt. Delrin® bearings, PVC shaft, HDPE sludge box. Available in 1.5 size only.

SERIES S

SERIES SS

SERIES CPP

SERIES PP

All units include: float switch, sludge box (HDPE on Models 1.5 and 4), a filtrate reservoir which serves as a support for mount-ing the conveyor frame, drain, single phase drive motor and starter. Standard edge seals are PVC, 140°F maximum. EPDM and silicon rubber edge seals are optional. Order filter media separately.

Model DF-1.5

Models DF-4 to DF-113

SPECIFICATIONS

FILTERMODEL

FILTERAREA

TANKCAPACITY

115V/1/60DRIVE

MOTOR

OVERALLDIMENSIONS (INCHES)

INLETHEIGHT

(INCHES)

MEDIAWIDTH

APPROX.SHIPPINGWEIGHT

FABRIC MICRON RATING

LENGTHA

WIDTHB

HEIGHT5 10 25 40 80

SQ. FT. GAL. HP C IN. LBS. GPM FLOW RATEDF-1.5DF-4

1.54

2049

1/151/3

5575

21.528

35.540

1719

1316.5

225320

25

36

410

614

923

DF-8DF-11

811

90115

1/31/3

7190

5050

4040

1919

3333

580760

1014

1217

2028

2839

4562

DF-15DF-16.5

1516.5

130160

1/31/3

9890

4467

4040

1819

3350

9401025

1920

2325

3842

5358

8593

DF-19DF-24

1924

160200

1/31/3

89104

6262

4040

1818

5050

10251420

2430

2936

4860

6784

108136

DF-27DF-29

2729

400500

1/21/2

136162

6868

5252

3030

5050

24003110

3436

4144

6873

95102

153164

DF-40DF-57

4057

600900

1/23/4

194259

6868

5252

3030

5050

37505250

5071

6080

100143

140200

226323

DF-96DF-113

96113

13701575

3/41

380427

6868

5252

3030

5050

77008655

120142

144160

240286

336400

544646

17

F-701R

345


ORDER DISPOSA-FABRIC MEDIA SEPARATELY, use Price Code No.

* Add width to Model No. - Example: SF-W125-13" See Flow Rate Chart and Micron Selection Guide

OPTIONAL EQUIPMENT

TO ORDER, use Price Code Number

See page 4 for reservoir pumps.

FILTERAREA

(SQUAREFEET)

SERIES S SERIES SS SERIES CPP SERIES PP

MODELPRICE

CODE NO.MODEL

PRICECODE NO.

MODELPRICE

CODE NO.MODEL

PRICECODE NO.

1.548

11

DFS-1.5-SDFS-4-SDFS-8-SDFS-11-S

49-141449-100049-100349-1006

DFS-1.5-SSDFS-4-SSDFS-8-SSDFS-11-SS

49-1413A49-1038A49-1040A49-1042A

DFS-1.5-CPPDFS-4-CPPDFS-8-CPPDFS-11-CPP

49-113949-005949-006049-0061

DFS-1.5-PP––––––

49-1415––––––

1516.519

––DFS-16.5-SDFS-19-S

––49-100749-0015

––DFS-16.5-SSDF-19-SS

––49-1043A49-0048A

DF-15-CPP––DF-19-CPP

49-0062––

49-0064

––––––

––––––

24272940

DF-24-SDF-27-SDF-29-SDF-40-S

49-001849-002149-002449-0027

DF-24-SSDF-27-SSDF-29-SSDF-40-SS

49-0050A49-0052A49-0054A49-0056A

DF-24-CPPDF-27-CPPDF-29-CPPDF-40-CPP

49-006549-006649-006749-0068

––––––––

––––––––

5796113

DF-57-S DF-96-SDF-113-S

49-003049-007449-0075

DF-57-SS––––

49-0058A––––

DF-57-CPP––––

49-0069––––

––––––

––––––

RA

YO

N /

PO

LYE

ST

ER

BL

EN

D

CO

AR

SE

MODELNO. *

MICRON

-13" WIDTH* -16 1/2" WIDTH* (LOTS OF 2 ONLY) -33" WIDTH -50" WIDTH*

YARDSPER

ROLL

PRICECODE NO.

WEIGHT(LBS)

YARDSPER

ROLL

PRICECODE NO.

WEIGHT(LBS)

YARDSPER

ROLL

PRICECODE NO.

WEIGHT(LBS)

YARDSPER

ROLL

PRICECODE NO.

WEIGHT(LBS)

SF-W125SF-W105SF-W090

12510590

100100100

49-0257 1B49-0258 1B49-0259 1B

222

500500500

49-0090 1B49-0093 1B49-0165 1B

11.511.512.0

500500500

49-0091 1B49-0094 1B49-0166 1B

232323

500500500

49-0092-1B49-0095-1B49-0167-1B

353535

SF-W080SF-W055

8055

100100

49-0260 B49-0262 B

22

500500

49-0099 B49-0105 B

9.010.5

500500

49-0100 B49-0106 B

1821

500500

49-0101 B49-0107 B

2732

ME

DIU

M SF-W040SF-W025SF-W020

402520

100100100

49-0263 B49-0264 B49-0265 B

222

500500500

49-0108 B49-0111 B49-0070 B

12.014.518.0

500500500

49-0109 B49-0112 B49-0071 B

242936

500500500

49-0110 B49-0113 B49-0072 B

364455

FIN

E SF-W010SF-W005SF-W001

1051

505050

49-0266 B49-0267 B49-0268 B

222

200200200

49-0114 B49-0117 B49-0120 B

14.017.527.5

200200200

49-0115 B49-0118 B49-0121 B

283555

200200200

49-0116 B49-0119 B49-0122 B

435384

PO

LYP

RO

SF-P080SF-P055

8055

100100

49-0260 BPP49-0262 BPP

22

500500

49-0099 BPP49-0105 BPP

9.010.5

500500

49-0100 BPP49-0106 BPP

1821

500500

49-0101 BPP49-0107 BPP

2732

SF-P040SF-P025SF-P020

402520

100100100

49-0263 BPP49-0264 BPP49-0265 BPP

222

500500500

49-0108 BPP49-0111 BPP49-0070 BPP

12.014.518.0

500500500

49-0109 BPP49-0112 BPP49-0071 BPP

242936

500500500

49-0110 BPP49-0113 BPP49-0072 BPP

364455

DESCRIPTION PRICE CODE NO.

FLOAT ACTIVATED LEVEL CONTROL SWITCH FOR RESERVOIR PUMPNEMA 4. For single phase motors to 11/2 HP @ 115V or 2 HP @ 230VAC. Used as a pilot device on three phase magnetic motor start-ers. Complete with float ball and mounted in reservoir tank for pump-down operation. Separate motor starter is required for 3-phase motor (see below).

49-0162

RESERVOIR PUMP INSTALLATION AND WIRING 49-0173

MOTOR STARTER FOR RESERVOIR PUMP3 phase with transformer and 24VAC control circuit1 phase with transformer and 24VAC control circuit

O-MS3P-SO-MS1P-S

EDGE SEALS

Models 1.5 - 8Models 11 - 16.5

EPDM200OF max.

SILICON RUBBER3000F max.

49-0500 A49-0651 A

49-0500 B49-0651 B

CONVEYOR BELTSFor Series DF-19S through DF-113S (Standard belts are galvanized steel.)304 stainless steel316 stainless steel

ADD TO MODELADD TO

PRICE CODE NO.

-304-316

BC

17

F-701R

346


RESERVOIR PUMPS (not installed)

NOTE: 1/15 HP to ¾ HP motors are 1 phase, 1 HP and up are 3 phase. 3 phase motors require a separate motor starter.

FLOW RATE

90µ 105µ 125µ

80µ

55µ

40µ

25µ10µ 5µ

1µ

FABRIC SELECTION

SIZING INSTRUCTIONS:1. Select the desired micron retention fabric from the

chart above.2. Using the Flow Rate chart on the preceding page,

determine the flow per square foot for the selected viscosity and fabric.

3. Divide the total flow (GPM) you desire by the num-ber obtained in step 2. The resultant is the size, in square feet of filter area your Automatic Fabric Filter should have.

FLOW HORSEPOWER CAST IRON POLYPROPYLENE CPVC

GPM @ TDH (ft.) CI PP & CPVC MODEL PRICECODE NO.

MODEL PRICECODE NO.

MODEL PRICECODE NO.

515244075

1111202420

1/151/41/23/42

1/5–

1/33/42

SCI 1.5SCI 4SCI 8SCI 15SCI 24

49-014949-015049-015149-015349-0156

E 3/4PP––

EOPP1EOPP3EOPP4

45-0030A––

39-1121 A39-1123 C39-2124 J

E3/4C––

EOC1EOC3EOC4

45-0027 1A––

39-1221 A39-1223 C39-2224 J

115145200

352535

235

25

7 - 1/2

SCI 29SCI 40SCI 57

49-0158 A49-0159

49-0160 A

EHP2EHP5

––

45-062345-0645

––

EHC2EHC5EHM2

45-012345-014545-1211

APPLICATIONMICRON SELECTION GUIDE

125 105 90 80 55 40 25 10 5 1

Paint spray booth - waterZinc & iron phosphating

WA

TE

R S

OL

UT

ION

S● ● ● ●

●

●

● ● ●

Caustic washing solutionsWaste treat - metal hydroxide

● ● ● ● ● ● ●

● ● ● ●

Grinding - steelGrinding - cast iron

● ● ●

●

●

●

●

●

●

●

●

●

●

●

Grinding - aluminumGrinding - carbide

● ● ●

●

●

●

●

●

●

●

Belt grinding - steelBelt grinding - zinc

● ●

●

●

●

●

●

●

●

●

●

●

Grinding - hard plasticsGrinding - soft plastics ●

●

●

●

●

●

●

●

●

Grinding - steel rollGrinding - brass ● ●

●

●

●

●

●

●

●

●

●

Grinding - bronzeGrinding - aluminum ● ●

●

●

●

●

●

●

●

● ●

Lapping (Oil 30 - 100)Honing (Oil 20 - 100)

OIL

100-

150

SS

U

●

●

●

●

●

●

●

●

●

●

QuenchingGrinding - aluminum ● ● ●

●

●

●

●

●

●

●

●

●

Belt grinding - steelBelt polishing - zinc copper

● ● ●

●

●

●

●

●

●

●

● ●

Belt grinding - steelThread grinding - steel

OIL

150-

250

SS

U

●

●

●

●

●

●

Flute - tap die grindingCrush & form grinding

●

●

●

●

●

●

Machine toolturning/milling

SY

NT

HE

TIC

● ● ● ● ●

Registered Trademark: Derlin - DuPont

17

ROLL-A-FILTER©F-703D

MEDIAWIDTH

Inches

10590805540251051

8040

5 - 10

150150150150150150757575

15015075

49-0175-149-0178-149-018149-018449-018749-019049-019349-024049-0243

———

W105W090W080W055W040W025W010W005W001N080N040N010

49-0177-149-0180-149-018349-018649-018949-019249-019549-024249-0245

———

APPROXIMATEMICRON RATING

Typical applications include:

PARTNUMBER

PRICE CODE NUMBERAPPLICATION FEETPER ROLL 18" 24" 36"

Straining paint / Coarse filtrationFine straining / Paint filtration / Light oilCoarse filtrationCoarse filtrationMedium filtrationFine filtrationVery fine filtrationUltra fine filtrationUltra fine filtrationHigh temperature operation (to 400°F)Chemical applications (Fabrics have chemi-cal resistance of nylon 6.6)

49-0176-149-0179-149-018249-018549-018849-019149-019449-024149-024449-019649-019749-0198

Minimum order - 2 rolls

DISPOSABLE FABRIC MEDIA (Order separately)

TO ORDER

28 x 19 x 528 x 25 x 547 x 25 x 547 x 37 x 559 x 37 x 5

1824243636

RAF-2SRAF-3SRAF-4SRAF-5SRAF-6S

PRICECODE NO.

79-027879-027979-028079-028179-0282

2-1/33-1/4

69

12

FILTERING AREA

Sq. Ft.

Simply place the ROLL-A-FILTER on top of an open drum or recirculating tank and pour or route the liquid to be filtered into the filter tray. When the filter fabric accumulates enough solids, as indicated by the liquid pool, pull it forward, tear/cut it off and discard. The handles on the filter media support basket provide an easy and clean method of lifting and discarding the sludge laden media.

All units are made of heavy gauge steel, and are designed with inte-gral clean catch basin with center discharge hole. Units conveniently install over sumps to eliminate frequent cleanout.

STRAINING - Paints & varnishes

FILTERING - Chemicals, cutting and grinding fluids, oil

PILOT TESTING - Waste treatment, phosphating

SHIPPINGWEIGHT

1934466174

MODELNUMBER

NOMINALDIMENSIONS

L x W x HInches Lbs.

RA

YO

NN

YL

ON

PO

LY-

ES

TE

R

Steel construction coated with chemically re-sistant, oven cured two-part epoxy paint.

Heavy duty perforated steel filter media support basket with handles

Rugged steel support frame and sloped bottom basin

Safe tear bar / cutting guide

Models RAF-2S & -3S conveniently fit standard 55 gallon drums

●

●

●

●

●

USING DISPOSABLE FABRIC MEDIA

For further purification or recycling efforts, coalescing filters to separate liquids (i.e. oil/water) are available. Consult Application Engineering Department.

Note: Flow capacities vary greatly depending on liquid and volume of solids.

347

17

SERIES 'CB' CARTRIDGE / BAGFILTRATION SYSTEM

● COMPLETELY PRE-ENGINEERED AND ASSEMBLED

● QUICK CHANGE REUSABLE FILTER MEDIA MEANS FAST PAYBACK

● PERMITS WATER REUSE

● PREVENTS NOZZLE PLUGGING

● PROVIDES BETTER CLEANING

● PREVENTS POLLUTION

● NO BACKWASH REQUIRED

● AVAILABLE WITH AUTOMATIC ON / OFF PUMP CONTROL

The Cartridge / Bag system is a 2-stage liquid-solid separation system designed to provide high solids loading capabilities for applications requiring recirculat-ing filtration of a process reservoir. Typical applications include the removal of particles from glass and plastic in bottle washing operations and the removal of board fiber, wheel grit, copper and other metals from water used in PC board deburring and scrubbing equipment.

The first stage employs a primary filter tank con-taining 8 gravity flow filter bags to collect bulk particles separated from rinse water. This stage provides 17.6 ft.2 of filter surface area and is capable of filtering particles from 100 micron to 5 micron, depending upon the mi-

FEATURES: ● Flow control valve

● High solids loading

● Vinyl coated steel baseCB FILTRATION

SYSTEMPC BOARD OR BOTTLE

SCRUBBER

For recirculating filtrationon a reservoir

Shown withcover open

cron rating of the filter bags selected. The filter bags are attached to a manifold with cam-lock quick-disconnect couplings for minimal down-time when servicing. The manifold includes an overflow vent which prevents back-up of system flow.

A circulating pump can be manually activated, or automatically activated with an optional level control, to transfer the filtered water from the primary filter tank to the second stage.This stage consists of a final trap filter chamber which uses a 2 micron pleated paper filter cartridge with 32 sq. ft. of surface area to polish the water so that clear water can be recycled to the process or discharged to a drain.

F-601H

348

17

F-601H

MOTORTEFC, 1.0 HP

3450 RPM @ 60 Hz2850 RPM @ 50 Hz

MOTORTEFC, 1.5 HP

3450 RPM @ 60 Hz2850 RPM @ 50 Hz

2750

2751

115-230V/1/60230V/460V/3/60

380V/3/50

O-1490

O-MS1PO-MS3P

PRICECODE NO.DESCRIPTION

LEVEL CONTROL (motor starter required) Automatic on / off pump controlMOTOR STARTER Watertight push button, 115-230V/1/50-60 230-460V/3/50-60Note: Add -S to motor starter PCN when ordering motor starter for use with O-1490 level control, i.e., O-MS3P-S

FILTER MEDIA (Bags ordered separately, 1 cartridge included in original equipment.) Bags - Polypropylene, size 7" x 16" (8 req'd) 5 micron 10 micron 25 micron 50 micron 100 micron Replacement pleated cartridge 2 micron (1 required)

88-0848A88-0848B88-0848C88-0848D88-0848E

Entire system constructed ofcorrosion resistant materials

for long service life.

Pump-MotorMotor Starter

(Optional)

32-1/2"(826mm)

51"(1295mm)

Reservoir & PrimaryBag Filters

2" NPTInlet

Final FilterChamber

1/2" NPTDrain

1" NPT Outlet

13-1/2" (343mm)

50"(1270mm)

TOP VIEW

2" NPT Inlet

2-5/8"(67mm)

SPECIFICATIONS

19" (483mm)

29"(737mm)

OPTIONAL

SIDE VIEW

PRIMARY FILTER TANK

Eight 5, 10, 25, 50 or 100 micron polypropylene filter bags (order separately) with quick-disconnect couplings provide 17.6 sq. ft. (1.6 sq. m) total area primary filtration by gravity flow to a 36" x 24" x 32" (914 x 610 x 813 mm) deep polyethylenereservoir. Reservoir provided with cover.

AVAILABLE WITH: PVDF CENTRIFUGAL PUMP

Provides 30 U. S. GPM at 18 PSI @ 60 Hz (95 LPM at 1.2 bar @ 50 Hz) with Viton® mechanical seal and "O"-ring. Flow control valve on 1" PVC pipe between pump and final filter.

or NORYL® SELF-PRIMING CENTRIFUGAL PUMP

Provides 30 U. S. GPM at 21 PSI @ 60 Hz (95 LPM at 1.4 bar @ 50 Hz) with Viton® mechanical seal and "O"-ring. Flow control valve on 1" PVC pipe between pump and final filter.

FINAL TRAP FILTER CHAMBERConstructed of PVC with quick opening swing bolts and tee handles. Supplied with pressure gauge. Includes one 4" x 36" pleated paper filter cartridge of 2 micron, 32 sq. ft. (3.0 sq. m.) expanded filter area.

VINYL COATED STEEL BASEApproximate shipping weight - 200 lbs. (91 kg.)

PRICECODE

NO.

CBF 65x58 1½x1½K3V(M2)-C1.5

CBF 65x58 1½x1½K3V(M2)-D1.5

MODEL with PVDF end suction

'K' pump


36"(914mm)

PL436-2-4

Motor Starter(Optional)

115-230V/1/60 230V/460V/3/60

380V/3/50

PRICECODE NO.

2733

2734

MODEL with NORYL self- priming

'G' pump

CBF 65x58 GNOKCVN-C1.0

CBF 65x58 GNOKCVN-D1.0

349

SERIES 'CB' CARTRIDGE / BAG FILTRATION SYSTEM (cont’d)

17

RECESSED PLATEFILTER PRESS F-705R

Biological SludgeMetal Hydroxide SludgeLime Treated Sludge

AVERAGEDRY WEIGHT/CUBIC FOOT

The Recessed Plate Filter Press will compact sludges to a dry cake with a density that is depen-dent upon the ultimate compaction pressure and the characteristics of the particular sludge. Each pressload will require from 2-4 hours cycle time. To insure adequate time, the press should be sized for at least 8 hours working capacity.The table and formula below can be utilized to size your press. To confirm your sizing and evaluate the process for your application with a laboratory-sized model,

contact the Application Engineering Dept. to ar-range a pilot test. Presses feature structural steel frame, coated with tough chemical resistant epoxy paint. High density molded polypropylene filter plates are light weight and corrosion resistant. Special polypropyl-ene quick cake release filter cloths. Air actuated hydraulic system for parting and closing the filter plates. Automatic self-compensating hydraulic system. Conveniently located operator control console.

TO SIZE YOUR PRESS, the following information is required:

● MANUAL HYDRAULIC 0.6 to 3 cu.ft.expandable

● SEMI-AUTOMATIC 1 to 50 cu.ft. expandable

● AIR BLOWDOWN MANIFOLD

● CORROSION RESISTANT

● 40-60% SOLIDS CONCENTRATION

● LOW ENERGY REQUIREMENT

● EASY DROPOUT CLEANING

WASTE & SEWAGE TREATMENTBREWING / CEMENT / CERAMIC MINING & PLATING INDUSTRIESFOOD & VARNISH PROCESSING

CHEMICALS

LIQUID / SOLID SEPARATION FOR:

A. Total gallons to be processed in selected press in specified period, e.g., U.S gals./8 hours. Twenty-four hours can be used to insure adequate capacity.

B. Percent by weight of filterable suspended solids.

C. Average dry weight per cubic foot for a particular sludge (obtained from table.)

SLUDGE TYPE% OF CAKE

DRY WEIGHTSOLIDS

15-2525-4015-60

152530

CALCULATIONS:

Model 25-48PPwith optional pneumatic

plate spreader

A X B X 8.33 LBS./GAL. C

(U.S. GALS./ 8 HRS.) X ( % SUSPENDED SOLIDS) X 8.33 LBS./GAL.

(AVERAGE LBS. DRY WT. / CUBIC FT.)OR

CU. FT. CAPACITY FOR A DURATION

=

350

17

F-705R

1-24PP2-24PP3-24PP4-24PP5-24PP6-31PP8-31PP

10-31PP15-31PP20-31PP25-48PP30-48PP40-48PP50-48PP

DIMENSIONS (IN.)

37

101417121620304021253442

46

1219

43-080443-080543-080643-0807

DESCRIPTION

IN-OUT NPT& SQUAREPLATE SIZE

43-064143-064243-064443-0649

DESCRIPTION PRICE CODE NUMBER

FOR PLATE SIZEPneu. plate spreaderSafety light curtains

Replacement cloth Non-gasketed Gasketed

SF-U48*SF-U48*G

43-066243-0670

43-0671

Automatic pump control 3 stage 4 stage

Hydraulic interlock for feedpump air supply

55-7120A55-7144A55-7208

43-066743-0648

Air diaphragm pump, Polypropylene w/nitrile See Bulletin P-605Drum disposal system w/extended legs & carbon steel chute for 1 to 5 cu. ft. size

Self-dumping sludge hopper (Order 2X press capacity)

½” - 14 GPM 1” - 40 GPM 2” - 135 GPM

43-0668

Manual hydraulic 18”Semi-automatic 24”

48”43-065843-0661

18”--

SF-U18*SF-U18*G

SF-U24*SF-U24*G

24”43-0680

-

31”43-065643-0659

SF-U31*SF-U31*G

Expander piece (For the future addition of up to 10 plates)** Additional plates (each)

43-067343-0677

43-067243-0676

43-067443-0678

43-067543-0679

PRICE CODE NO.

Consult Application Engineering Dept. for options not shown, such as high pressure units, catwalks, drum carts, etc.

PRESS-FULL indicator

6 cu. ft.10½ cu. ft.21 cu. ft. (Cu. ft. capacity of dumpster is 32 cu. ft. total of 2 hopper units provided)

CUBICFEET 1

0.61.02.03.0

123456810152025304050

NOTE: Air blowdown connections are ½” NPT on all models.

1½” x 1”18½”(470mm)

32

2½” x 1½”24” (610mm)

3” x1½”31½”(800mm)

1 Based on 1¼” thick filter cake.

3” x 2”48” (1200mm)

A B C D E F

24 49 31

37415573

52567087

39

48

66

31

40

58

56

63

86

30

30

35

8493

100107116109119129154179133144169191

57677480898292

102127152105116141163

MANUAL HYDRAULIC

NON-GASKETED GASKETED

PRICE CODE NUMBER

43-0804G43-0805G43-0806G43-0807G

43-060143-060243-060343-0604A43-0605A43-060643-060843-061043-0615A43-0620A43-0625A43-0630A43-064043-0650

43-0601G43-0602G43-0603G43-0604AG43-0605AG43-0606G43-0608G43-0610G43-0615AG43-0620AG43-0625AG43-0630AG43-0640G43-0650G

MODEL

0.6-18PPMH1-18PPMH2-18PPMH3-18PPMH

OPTIONAL EQUIPMENT

SLUDGE HOPPER Self-dumping hoppers to transfer compacted solids from the press to a large roll-off type container. The hoppers, specifically engineered for each class of press, are easily moved with forklift truck and dumping is accomplished merely by a trip handle.

AUTOMATIC PUMP CONTROL Allows progressively increasing air pressure on diaphragm pump to attain a denser, drier cake.

DRUM DISPOSAL SYSTEM For presses up to 5 cubic feet. Includes chute and extended legs to raise press to permit adequate clearance for a drum.

PLATE SPREADER, SAFETY LIGHT CURTAIN, PRESS-FULL INDICATOR and HYDRAULIC INTERLOCK are additional features on some models.


SEMI-AUTOMATIC

NO. OFCHAMBERS

8008509401060

APROX.WEIGHT(LBS.)

1700190020502150230042004450490055006000

11,38011,85013,10014,000

DIMENSIONS

* To designate cloth position, add to Price Code Number: H Head T Tail M Intermediate**Expander piece for maximum of 7 plates for manual hydraulic 18” size plates .

RECESSED PLATE FILTER PRESS

351

17

LABORATORYFILTER PRESS F-710C

For Lab Analysis - Small Batch Production - Field Testing

flow control valve, hoses, manual hydraulic pump and drip pan. Entire assembly is mounted on a vinyl coated steel base. Flow pattern is corner inlet with three individual corner discharge lines.

Dimensions: 42" (1.1m) L x 13" (.33m) W x 22" (.56m) HShipping Weight: 95 Lbs (43 kg.)Maximum operating temperature: 150° F (66° C)

● PLATE AND FRAME DESIGN Dual capacity- Can be used with one or two frames for adjusted volume - .01 cu. ft. (283 cm3) or .02 cu. ft. (566 cm3) Area per frame - 17in2 (110 cm2)

● INCLUDES POLYPROPYLENE PLATES AND FILTER CLOTH Suitable for most waste solutions

● AIR DIAPHRAGM PUMP Polypropylene construction Flows adjustable to 5 GPM (15.7 LPM) Pressure adjustable to 60 PSI (4.22 kg/cm2)

The Lab Filter Press is designed for lab analysis and small batch production. This press is also very useful for testing for upscaling to full production-size semi-automatic or manually operated presses. Includes polypropylene plates, filter cloth, air diaphragm pump, pneumatic controls, pressure gauges, inlet

LAB FILTER PRESS PRICE CODE NO.

MODEL .02 - 7PPMH 43-0857

REPLACEMENT CLOTHS(Set of 4)

PRICE CODE NO.

43-0822SF - 7 x 7

TO ORDER Hydraulic Operation

Pressure GaugeFlow

Control Valve

Air Filter / PressureRegulator

Pressure Gauge

DiaphragmFeed Pump

Test Slurry

Drip Pan

352

Documents

FILTRATION SYSTEMS FOR