1
Grade 300 40 bar dia Grade 500 70 bar dia min.lap See Note See Note See Note See Note 200 x 200 haunch 75mm minimum granular fill Damp proof membrane Interior plaster/finish as specified Horizontal reinforcement Grout 17.5 MPa (except sea spray zones 25MPa) Vertical reinforcement central to cavity 100mm slab Reinforcing mesh Concrete (17.5 MPa) Firth HotBloc ® Polystyrene Exterior plaster/finish as specified with applied waterproof coating Finished floor level Ground clearence per E2/AS1 D12 D12 ties @ 600 ctrs. (lap 600 min.) www.firth.co.nz Disclaimer : This information is intended solely as a guide for use of Firth products. Before using a Firth product you should ensure that the product is suitable for use in the specific application. Nothing in this information constitutes a statement of fitness for particular purpose - appropriate expert advice should always be obtained. Firth makes no warranty regarding the use of this information with non-Firth product. © 2009 . The copyright of this document is the property of Firth and shall not be reproduced, copied, loaned or disposed of directly, or indirectly, nor used for any purpose other than that for which it is specifically furnished without prior consent. For Technical Advice: Ph. 0800 800 576 Firth HotBloc Edge Thickened Slab Detail 103 103_edge_thickened .dwg February 2009 Scale 1:10 ® Notes: ® If a rebate is required increase footing width to block width +150mm.

Firth HotBloc · Gr a de 3 0 0 40 b a r d ia Gr a de 5 0 0 70 b a r d ia m i n. l ap Se e N ot e S e e N o te See Note Refer to NZS 4229 or specific design for dimension, reinforcing,

  • Upload
    others

  • View
    1

  • Download
    0

Embed Size (px)

Citation preview

Page 1: Firth HotBloc · Gr a de 3 0 0 40 b a r d ia Gr a de 5 0 0 70 b a r d ia m i n. l ap Se e N ot e S e e N o te See Note Refer to NZS 4229 or specific design for dimension, reinforcing,

Gra

de 3

00 4

0 ba

r dia

Gra

de 5

00 7

0 ba

r dia

min

.lap

See

Not

eSe

e N

ote

See Note

Refer to NZS 4229 or specific design for dimension, reinforcing, and ground clearances

See Note

200 x 200 haunch

75mm minimum granular fill

Damp proof membrane

Interior plaster/finish asspecified

Horizontal reinforcement

Grout 17.5 MPa(except sea spray zones 25MPa)Vertical reinforcement central to cavity

100mm slab

Reinforcing meshConcrete (17.5 MPa)

Firth HotBloc®

Polystyrene

Exterior plaster/finish as specifiedwith applied waterproof coating

Finishedfloor level

Groundclearence

per E2/AS1D12

D12 ties @ 600ctrs.(lap 600 min.)

www.firth.co.nzDisclaimer : This information is intended solely as a guide for use of Firthproducts. Before using a Firth product you should ensure that the product issuitable for use in the specific application. Nothing in this informationconstitutes a statement of fitness for particular purpose - appropriate expertadvice should always be obtained. Firth makes no warranty regarding the useof this information with non-Firth product.

© 2009 . The copyright of this document isthe property of Firth and shall not bereproduced, copied, loaned or disposed ofdirectly, or indirectly, nor used for anypurpose other than that for which it isspecifically furnished without prior consent.For Technical Advice: Ph. 0800 800 576

Firth HotBlocEdge Thickened Slab Detail 103103_edge_thickened .dwg

February 2009Scale 1:10

®

Notes:

Refer to CCANZ CO.01:2011 for situations where a floor rebate is required.••

®

• If a rebate is required increase footing width to block width +150mm.