Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
PERFORMANCE EVALUATION OF
FIXED WINDOW “3000 SERIES LOW PROFILE FIXED – 3-1/4 " FRAME” For Dominion Doors & Windows Ltd.
IN ACCORDANCE WITH: AAMA/WDMA/CSA 101/I.S.2/A440-08
AND CSA A440S1-09
Report to: Dominion Doors & Windows Ltd. 130 Pennsylvania Ave., Unit 8 Concord, ON, Canada L4K 4A8 Attention: Bill Pappas Consultant: Jean-Michel Lerdu Telephone: 905-761-9722 Fax: 905-761-1670 Email: [email protected] Original Report No.: 17-06-M0260-D1 5 Pages, 1 Appendix
Proposal No.: 17-006-521203 Original Date: October 9, 2018
Product Extruder: Vision Extrusions Product Manufacturer: Dominion Doors & Windows Ltd. Product Type: Fixed Window Product Series/Model: 3000 Series Low Profile Fixed – 3-1/4" Frame Primary Product Designator: Class CW – PG3360 – Size tested 1500 x 1500 mm – Fixed window
Class CW – PG70 – Size tested 59.06 in x 59.06 in – FW Secondary Product Designator: Positive Design Pressure: 3360 Pa (70.00 psf) Negative Design Pressure: 3360 Pa (70.00 psf) Water Penetration Resistance: 730 Pa (15.00 psf) Air Infiltration/Exfiltration: Canadian Fixed Level Report Number: 17-06-M0260-D1 Test Completion Date: June 5, 2018
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Page 2 of 5 For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1
1.0 INTRODUCTION
At the request of Dominion Doors & Windows Ltd., Exova was retained to evaluate the physical performance of a fixed window identified as “3000 Series Low Profile Fixed – 3-1/4" Frame”, in accordance with AAMA/WDMA/CSA 101/I.S.2/A440-08 Standard, “NAFS – North American Fenestration Standard/Specification for windows, doors, and skylights” and CSA A440S1-09 Canadian Supplement, as outlined in proposal number 17-006-521203.
Tests results reported herein qualify similar frame window profiles including glass stop profiles for double and triple glazed units, verified by Vision Extrusions’ consultant. See die drawings in Appendix A.
Exova Specimen No.: 17-06-M0260-1 Type: Fixed Window Model: 3000 Series Low Profile Fixed - 3-1/4" Frame Overall Window Size: 1500 mm x 1500 mm (59.06" x 59.06") Sampling: Not Applicable Frame Grouping: Tests results reported herein qualify similar fixed window identified as “3000
Series Low Profile Fixed – 4-1/2" Frame”, Extruded PVC, 1500 mm x 1500 mm x 114 mm (59.06" x 59.06" x 4.50"). See die drawing on page 3 of Appendix A.
2.0 SAMPLE DESCRIPTION
The following sample description has verified by Exova. Details and drawings of the described test specimen, as provided by the manufacturer, have been included in Appendix A. Product Type: Fixed Window
Frame: Extruded PVC, 1500 mm x 1500 mm x 83 mm (59.06" x 59.06" x 3.25") Joinery:
Frame: Welded, Mitred corners. Installation:
Test buck: Wood Buck Fasteners: Frame perimeter fastened with nine #8 x 1" pan head screws, four screws per
side, 425 mm (16.73") c/c, one at the head, mid-span. Sealant: Interior and exterior frame perimeter sealed with flexible sealant.
Glazing Type: One, dual glazed, annealed, overall thickness 22.2 mm (0.86"), glass thickness
4 mm (0.16"), gap thickness 15.9 mm (0.63"), aluminum spacer, dual sealed, air filled, clear.
Glazing Method: Laid in glazed, dry glazed.
Glazing Stop: Extruded PVC, interior perimeter. Co-extruded Fin: Flexible PVC, 2 rows, interior perimeter, at glazing stop.
Flexible PVC, 1 row, dual-fin, exterior perimeter, at glazing upstanding leg. Setting Block: Foam/Rubber, six, 38.1 mm x 19.1 mm x 4.8 mm (1-1/2" x 3/4" x 3/16"), two at
the sill, 50 mm (1.97") from the ends, two per side, 80 mm (3.15") from the ends. Partial Heel Bead: Flexible sealant, sill/jamb, 203 mm (8.00") long, glazing cavity, glass stops. Cap Bead: Flexible sealant, sill/jamb, 203 mm (8.00") long, glass stops at fins. Corner Bead: Flexible sealant, exterior glazing corners.
Drainage/Ventilation: Frame:
Drain Slot: Two, 15.7 mm x 2.7 mm (0.62" x 0.11"), bottom glazing cavity, 80 mm (3.15") from the ends. Two, 12.8 mm x 2.7 mm (0.50" x 0.11"), bottom rail, 55 mm (2.17") from the ends, exterior face.
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Page 3 of 5 For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1
3.0 TEST RESULTS
Table 1 - Summarized Testing Results in Accordance with AAMA/WDMA/CSA 101/I.S.2/A440-08 and CSA A440S1-09 Canadian Supplement
Test Requirements Results Rating
Air Leakage Resistance
(Clause 5.3.2)
Per ASTM E283
Test Date:
January 15, 2018
Allowable rate of air leakage shall be less than or equal to the following,
L/s.m² (cfm/ft²), at the subsequent test pressure:
Test area, m² (ft²): 2.3 (24.22)
PASS
Canadian Fixed Level
Measured Air Leakage Rate, L/s.m² (cfm/ft²):
Test Pressure, Pa (psf): 75 (1.60)
Gateway: 1.5 (0.30) Infiltration: 0.03 (0.01)
Canadian Fixed Level: 0.2 (0.04) Exfiltration: 0.04 (0.01)
Water Penetration Resistance (Clause 5.3.3)
Per
ASTM E547
Test Date: February 14, 2018
No water leakage shall be observed at the following specified pressure
differential, Pa (psf):
No water leakage was observed at the following specified pressure
differential, Pa (psf): PASS
Gateway (CW30-FW)
Optional
Performance (CW100-FW)
Gateway Performance: Gateway Performance:
Test Pressure: 220 (4.50) Test Pressure: 220 (4.50)
Optional Performance: (US / CAN)
Optional Performance: (US / CAN)
Test Pressure (US): 580 (12.00) Test Pressure: 730 (15.00)
Test Pressure (CAN): 730 (15.00)
Uniform Load Deflection
(Clause 5.3.4.2)
Per ASTM E330
Test Date: February 15,
2018
No member shall deflect more that L/175 of unsupported span at the following
specified test pressures, Pa (psf):
Measured net deflection of Right Jamb, mm (in):
PASS
Gateway (CW30-FW)
Optional
Performance (CW70-FW)
Allowable deflection, mm (in): 8.4 (0.33)
Right Jamb span, mm (in): 1465 (57.68)
Gateway Performance: Positive: 0.7 (0.03)
Test Pressure: ±1440 (30.00) Negative: -1.4 (-0.05)
Optional Performance:
Test Pressure: ±3360 (70.00)
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Page 4 of 5 For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1
Table 1, Continued - Summarized Testing Results in Accordance with AAMA/WDMA/CSA 101/I.S.2/A440-08 and CSA A440S1-09 Canadian Supplement
Test Requirements Results Rating
Uniform Load Structural
(Clause 5.3.4.3)
Per ASTM E330
Test Date: February 15,
2018
There shall be no permanent damage to the window components after the following specified test pressures,
Pa (psf). No member shall have permanent
deflect more that 0.3% of span.
Measured permanent deflection of Right Jamb, mm (in): PASS
Gateway
(CW30-FW)
Optional Performance (CW70-FW)
Allowable permanent deflection, mm (in): 4.4 (0.17)
Right Jamb span, mm (in): 1465 (57.68)
Gateway Performance: Positive: 0.47 (0.018)
Test pressure: ±2160 (45.00) Negative: -0.10 (-0.004)
Optional Performance:
Test pressure: ±5040 (105.00)
Forced-Entry Resistance (Clause 5.3.5)
Per
ASTM F588
Test Date: June 5, 2018
No entry shall be gained during the following test sequence: For Type D Window no entry was
gained during the following specified test sequence: PASS
Grade 40
Load Identification
Grade Loads, N (lbf)
10 20 30 40
Disassembly T1:
5 min 10 min Disassembly T1: No Entry
Manipulation T1:
5 min 10 min Manipulation T1: No Entry
Thermoplastic Corner Weld (Clause 5.3.6.2)
Test Date:
May 11, 2018
The break shall not extend along the entire weld line when tested to failure.
Break did not extend along the entire weld line.
PASS
4.0 MODIFICATIONS
The following modification was made to the Dominion Doors & Windows Ltd., Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame”, Exova Specimen No.: 17-06-M0260-1, during testing to achieve the results stated in this report.
• Water Penetration Test: - Partial heel bead of flexible sealant was applied at the sill/jamb corners, 203 mm (8.00") in the
glazing cavity beneath the glass stops. - Cap bead of flexible sealant was applied at the sill/jamb corners, 203 mm (8.00") at the glass stop
fins.
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Page 5 of 5 For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1
5.0 CONCLUSIONS
Based on the results of the testing summarized in Tables 1, Dominion Doors & Windows Ltd., fixed window “3000 Series Low Profile Fixed – 3-1/4" Frame,” Exova Specimen No.: 17-06-M0260-1 met the following requirements as outlined in the AAMA/WDMA/CSA 101/I.S.2/A440-08 standard and CSA A440S1-09 Canadian Supplement. Tests results reported herein qualify similar frame window profiles including glass stop profiles for double and triple glazed units, verified by Vision Extrusions’ consultant. See die drawings in Appendix A. Performance Rating
• Air Leakage Resistance Canadian Fixed Level • Water Penetration Resistance 580 Pa (12.00 psf) (US) 730 Pa (15.00 psf) (CAN) • Uniform Load Deflection ±3360 Pa (70.00 psf) • Uniform Load Structural ±5040 Pa (105.00 psf) • Forced Entry Resistance Grade 40 • Thermoplastic Corner Weld Pass
Product Designation for Class CW:
• Class CW – PG3360 – Size tested 1500 x 1500 mm – Fixed Window • Class CW – PG70 – Size tested 59.06 x 59.06 in – FW Product Extruder: Vision Extrusions Product Manufacturer: Dominion Doors & Windows Ltd. Product Type: Fixed Window Product Series/Model: 3000 Series Low Profile Fixed – 3-1/4" Frame Primary Product Designator: Class CW – PG3360 – Size tested 1500 x 1500 mm – Fixed window
Class CW – PG70 – Size tested 59.06 x 59.06 in – FW Secondary Product Designator: Positive Design Pressure: 3360 Pa (70.00 psf) Negative Design Pressure: 3360 Pa (70.00 psf) Water Penetration Resistance: 730 Pa (15.00 psf) Air Infiltration/Exfiltration: Canadian Fixed Level Report Number: 17-06-M0260-D1 Test Completion Date: June 5, 2018
6.0 REPORT REVISION SUMMARY Revision No: Date: Description of Revisions: 17-06-M0260-D1 October 9, 2018 Original Document Reported by: Reviewed by: ______________________________ _____________________________________ Allan Lawrence, Ext. 11212 Sunny Ling, C.E.T., MET Ext 11412 Supervisor, Building Systems Assistant Operations Manager, Building Science Products Testing Division Technical Development, Building Systems Products Testing Division
This report and service are covered under Exova Canada Inc.’s. Standard Terms and Conditions of Contract which may be found on our company’s website www.exova.com, or by calling 1-866-263-9268.
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Appendix A For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1
APPENDIX A
Manufacturer’s Detail Drawings
(8 Pages)
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Appendix A For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1, Page 1 of 8
Triple Glazed: Annealed, overall thickness 34.9 mm (1.38"), glass thickness 4 mm (0.16"), gap thicknesses 11.5 mm (0.45"), aluminum spacer, dual sealed, air filled, clear. A.L
.
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Appendix A For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1, Page 2 of 8
A.L
.
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Appendix A For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1, Page 3 of 8
TE
ST
ED
PR
OF
ILE
A.L
.
TE
ST
RE
SU
LTS
QU
ALI
FY
FR
AM
E P
RO
FIL
ES
A.L
.
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Appendix A For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1, Page 4 of 8
TESTED PROFILE
A.L.
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Appendix A For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1, Page 5 of 8
TEST RESULTS QUALIFY FRAME PROFILE
A.L.
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Appendix A For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1, Page 6 of 8
TE
ST
RE
SU
LTS
QU
ALI
FY
FR
AM
E P
RO
FIL
E
A.L
.
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Appendix A For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1, Page 7 of 8
Evaluation of the Fixed Window “3000 Series Low Profile Fixed – 3-1/4" Frame” Appendix A For Dominion Doors & Windows Ltd. Report No. 17-06-M0260-D1, Page 8 of 8
A.L.