09/23/13

TYPE1Stationary Mount Base Model

TYPE2Stationary Mount + Shelf

TYPE3Stationary Mount + Shelf +

Camera Mount

TYPE4Rotating Mount + Shelf

Flat Panel Series Mobile Stand Instructions

2 / 12

Table of ContentsTable of Contents and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Assembly and InstallationAdjust upper and lower poles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Attaching to the base assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Install steel cross rods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Height adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Media shelf assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Assemble flat panel mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9Install mount to the frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Install camera mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Cable and wire installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11VESA mounting patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

WARNING!Severe personal injury and property damage can result from improper installation . Read instructions carefully before beginning .

• If you do not understand the instructions or have any concerns please contact a qualified local installer.

• Do not install or assemble if the product or hardware is damaged or missing, if you require replacement parts contact your local dealer .

• This product fits most 40˝- 60˝ flat panel displays; maximum weight for the display is 100 lbs . / 45 .5kg .

• Do not use this product for anything other than what it was originally designed .• This product contains moving parts, please use caution .• The manufacturer disclaims any liability for the modifications, improper installation

and installation exceeding maximum weight capacity. The manufacturer will not be liable for any damages arising out of the use of, or inability to use the product .

Tools Required - Phillips Screwdriver - Wrench

3 / 12

Part List

A1 x1

R1 x1

R2 x1 R3 x1

S1 x1S2 x1

A2 x4

A3 x4A4 x1

C1 x1

C1 x1C2 x2C2 x2 C3 x4

C3 x2

C4 x4C5 x4

B2 x2

B1 x1

B2 x2

B1 x1

B3 x2 B5 x2B5 x2*

B4 x4TYPE4

TYPE4

TYPE1, TYPE2, TYPE3

TYPE1, TYPE2, TYPE3

only: TYPE1, TYPE2, TYPE3

only: TYPE2, TYPE3, TYPE4

only: TYPE2, TYPE3, TYPE4

(B3 is pre-installed)

*1 is pre-installed

only: TYPE3

only: TYPE3

only: TYPE3

E x4 F x4G x4

D x2

H x4 J x4

K x4 L x1 M x1T x8N x2 P x2

M8x25mm

M8x20mm M6x10mmM5x10mm

M6x25mm M5x25mm

4 / 12

1

1

3

2

Adjust upper and lower polesLocate the spring plungers inside the bottom grommet hole of pole B1 (If your unit has B5 cross bar pre-installed remove prior) . Starting with the right side pole B2, push the spring plunger down and pull B2 up slightly and twist it slightly so that the spring plunger remains offset. This will make adjusting the pole easier. (figure 1)

Repeat the same steps for the left side pole B2 but use your right foot for stability instead . Align poles B2 and lock the spring plunger into place. (figure 3)

Remove B5 before step 1 .

Only for TYPE1, TYPE2, TYPE3

Hold the poles B1 & B2 with your hands and use your left foot on the cross bridge of B1 for stability . Pull B2 upward until you reach your desired height . Twist B2 so that the spring plunger locks into the nearest spring plunger hole. (figure 2)

B1

B1

B1

B2

B5

B2

B2 B2

Spring plunger

Spring plunger

B3 ispre-installed

figure 1 figure 2 figure 3Lift pole assembly so that the part remains upright and the

cable management holes are facing toward you.

5 / 12

2

1

2

3

2

1

3

Attaching to the base assembly

Thread casters A2 and washer A3 into the bottom of base A1 . Make sure all casters are locked to prevent movement during installation .

With allen wrench M attach lower poles B1 to base A1 with screw K . First through the bottom of base A1, then through the top of base A .

After screws K are firmly fastened, push down the screw cover A4 until it locks into place .

Lock Castersbefore assembly

K

K

A1

B1

M

1

A3 A3

A2

A2 A2

A2A4B1

A1

A3A3

2

Tighten Fully with wrench

cable management holes facing back

6 / 12

3

4

Install steel cross rods

Height adjustment

1 2

3

Remove the pre-installed screws on rod B5 . Making sure the upper poles B2 are aligned, slide rods B5 into the top openings .

Slide the upper poles B2 up or down to the different spring plunger holes for your desired height . Install grommet covers B4 into the grommet holes .

Press and hold both spring plungers to slide the upper poles B2 .

Refasten rods B5 with screws .

Phillipsscrewdriver

B5B5

B5

B5B2

B4

B4B4

B4

461 ⁄2

˝ - 6

21 ⁄2˝ H

/ 10

50m

m -

1500

mm

AssistanceRequired

CablesUnplugged

7 / 12

1

1

2

2

Remove the pre-installed screws on bracket R2 . Align bracket R2 to desired position and clamp R2 then retighten the long screws .

Using the short screws fasten bracket R2 to support R3 .

With allen wrench L and the short allen screws fasten shelf R1 to support R3 .

Phillipsscrewdriver

Phillipsscrewdriver

B1

R2

R2

R3

R3

R1

5

1

2

3

Media shelf assembly (TYPE2, TYPE3, TYPE4)

Before assembly make sure there is enough clearance for

the flat panel display

L

8 / 12

6a

1

3

2

Assemble flat panel mount (TYPE4)

First unscrew and remove the vertical supports C2 from mount C1 .

Align the screw threads C3 to the desired vertical support position of C2 . Screw support C2 into C1 and C3 . Insert support stoppers C4 followed by caps C5 .

Carefully attach mount to display using screws G,H or J . Through washer E, support C2 and spacer F .

1. C3

C12. C2C2

C2C2

C1

C2

3. C4

4. C5

FF

GG

H,JH,J

E EF

F

F EG, H, J

For a selection of mounting positions refer to page 12

Plastic spacers must be used to avoid any damage from screws

VESA: 200x400 - 400x400mm

VESA: 400x600 - 500x800mm

Phillipsscrewdriver

Phillipsscrewdriver

Displaynot included

Safety Precautions

M8x25mm (G)M5x25mm (H)M6x25mm (J)

Top of Display

9 / 12

6b Assemble flat panel mount (TYPE1, TYPE2, TYPE3)

Adjusting the mount (TYPE4) - After Step 7

C1C1

F

T T

F

H,JH,J

E EF

F

E

E

H, J

H, J

VESA: 200x200mm VESA: 200x200 - 600x400mm

Phillipsscrewdriver

Phillipsscrewdriver

Phillipsscrewdriver

Swivel90°

Safety Precautions

M5x25mm (H)M6x25mm (J)

Remove pre-installed screws Re-attach screws

10 / 12

7 Install mount to frame

Make sure casters are locked prior to

installation

Attach hooks on C1 onto cross rods B5

Secure lock hook fully

Lock not included

Lift up lock hook before installing

mount

Heavy Lifting: Assistance Required

C1

1

3 4

2

C1

B5

11 / 12

8

9

Install camera mount (TYPE3)

Cable and wire Installation

Please use care when inserting the wires and

cables into the grommet to avoid damage

For indoor use only. Avoid excessive wind,

heat & humidity.

Adjustable height

NP

Phillipsscrewdriver

S1

S2

09/23/13

12 / 12

10 VESA mounting patternsSlide vertical support rails to find the best assembly position for your display .

For 200x200mm VESA mounting position use brackets D .

D