FLIR FX™ Instruction Manual

Instruction ManualFLIR FX™

Instruction ManualFLIR FX™

#LX400067; r.27354/27358; en-US iii

Table of contents

1 Safety Precautions ............................................................................12 What is included with my FLIR FX camera?...........................................23 Get to know your FLIR FX camera........................................................3

3.1 Front ......................................................................................33.2 Top ........................................................................................33.3 Left ........................................................................................43.4 Right ......................................................................................43.5 Back ......................................................................................53.6 Indoor Stand............................................................................5

4 Optimizing Wi-Fi performance.............................................................65 How to set up your FLIR FX camera .....................................................8

5.1 FLIR FX Android™ setup............................................................85.2 FLIR FX iPhone® setup ........................................................... 155.3 FLIR FX Android™ tablet setup.................................................. 225.4 FLIR FX iPad® setup............................................................... 28

6 Connect to your camera in Direct Mode.............................................. 357 Connect to your camera in Cloud Mode.............................................. 388 How to mount your FLIR FX camera ................................................... 419 How to mount your FLIR FX camera to your windshield........................ 4610 Using your FLIR FX camera with a sports case.................................... 4811 Viewing your FLIR FX camera in high definition................................... 5312 How to change the name of your camera ............................................ 5613 How to change your camera’s password ............................................ 5914 Setting temperature and humidity alerts............................................. 6815 How to control the camera’s night vision LEDs.................................... 7216 Manual recording ............................................................................ 7617 Setting motion detection alerts and recording .................................... 7718 Setting sound alerts and recording.................................................... 8219 Viewing recordings via the FLIR FX app ............................................. 8520 How to create a Rapid Recap™ ......................................................... 8821 How to view a Rapid Recap............................................................... 9222 How to view recordings on a computer .............................................. 9623 Taking photos using the FLIR FX app ................................................. 9824 Using the digital zoom feature......................................................... 10125 Using the intercom ........................................................................ 10326 Notices......................................................................................... 106

#LX400067; r.27354/27358; en-US v

Safety Precautions1

• Camera is not weatherproof. Use the appropriate outdoor accessory if using the cam-era outdoors or where it will be exposed to moisture.

• Make sure that outdoor power outlets and cable connections are properly shelteredfrom the elements.

• Do not use the camera below 32°F / 0°C or above 104°F / 40°C.• Only use the camera with approved FLIR accessories.• Do not use or install the camera near a radiator or heat source.• Do not cover the camera with a towel or blanket as it may overheat.• Do not point the camera directly towards the sun or a source of intense light.• Be sure to disable the night vision LEDs when aiming the camera through a window toavoid glare in low-light conditions.

• Keep the cables at least 3ft / 1m away from baby cribs and out of reach of childrenand infants.

• Use the included cable clips to help keep cables away from children.• Do not disassemble the product. No user serviceable parts inside.• Do not disassemble or do a modification to the battery. The battery contains safetyand protection devices which, if damaged, may cause the battery to become hot, orcause an explosion or an ignition.

• If the camera is not used on a regular basis, be sure to charge the battery every 6months to keep the battery in working condition.

• Dispose or recycle the product and batteries in accordance with local laws, whichmay vary by location.

• If using an accessory with replaceable batteries, only use replacement batteriesspecified by FLIR. Use of other types of batteries may damage the product.

• The camera makes a clicking noise when changing between day and night modes.This clicking is normal and indicates that the camera filter is working.

• Do not connect a USB cable to both the camera and the stand at the same time.

#LX400067; r.27354/27358; en-US 1

What is included with my FLIR FXcamera?

2

The standard model FXV101–H comes with the following components:

• Camera with indoor stand• microUSB cable• 8GB class 10 microSD card pre-installed in the camera• Power adapter (US 120V)• Power points for European and UK use• Mounting screws and drywall anchors• Extra mounting / camera ID plate for convenience• Quick start guide and safety information

NOTE

Other models or configurations may come with slightly different components or accessories.

#LX400067; r.27354/27358; en-US 2

Get to know your FLIR FXcamera

3

3.1 Front

1. Infrared night vision LEDs: Allows the camera to see up to 33ft / 10m in totaldarkness.

2. Lens: Provides a wide-angle 160 degree field of view.3. Microphone: Allows you to hear the area around the camera.4. Speaker: Allows you to talk through your camera from your mobile device using 2-

way-talk.

3.2 Top

1. REC button / status LED: Press to start / stop manual recording.

LED colors:

• Flashing red: Camera is recording.• Solid orange: Camera is charging.• Solid green: Camera is fully charged.

#LX400067; r.27354/27358; en-US 3

Get to know your FLIR FX camera3

3.3 Left

1. WPS button: Used to connect the camera to a WPS-compatible router (not included).Press the WPS button on the router and then press the WPS button on the camera tomake the connection.

2. Power/Wi-Fi button: Press to turn the camera on. Press to switch the camera be-tween Direct Mode and Cloud Mode. Press and hold to turn off the camera.

3. Accessory connector: Allows the camera to slide into compatible accessories.

3.4 Right

1. microSD slot: Insert a microSDHC, or microSDXC card between 8GB and 64GB forrecording on the camera. It is recommended to use microSD class 10 or higher cards.

2. microUSB port: Connect a microUSB cable to the camera for charging or to savevideo file from the camera to a PC or Mac.

NOTE

While the camera is connected to a computer, you will not be able to connect to it using a mobiledevice. Do not connect a USB cable to both the camera and stand at the same time.

#LX400067; r.27354/27358; en-US 4

Get to know your FLIR FX camera3

3.5 Back

1. Direct Mode LED: Indicates the camera is in Direct Mode. When the camera is in Di-rect Mode, you can connect to the Wi-Fi hotspot created by the camera to connect toit in areas without access to wireless.

2. Cloud Mode LED: Glows solid green to indicate the camera is connected to a Wi-Finetwork, allows you to connect to the camera from anywhere. Flashing indicates thecamera is connecting to a Wi-Fi network.

3. Temperature/humidity sensor (built-in): Senses the temperature and humidity inthe room.

4. Accelerometer: Senses the motion of the camera.

3.6 Indoor Stand

1. Connector: Allows the stand to connect to the camera.2. Ball joint: Provides the camera with a flexible range of motion.3. Expanded battery: Provides extra battery life for the camera.4. microUSB port: Connect a microUSB cable to the stand for charging the battery in

the camera and stand.

NOTE

While the camera is connected to a computer, you will not be able to connect to it using a mobiledevice. Do not connect a USB cable to both the camera and stand at the same time.

5. Mounting plate: Enables the camera to be mounted to a wall. The mounting platecan be removed from the camera. The camera comes with an additional mountingplate, so you can keep a permanent mounting position while still having the ability tomove the camera around.

6. Device ID label: Contains the Device ID and QR code used for initial setup using themobile app.

NOTE

When performing firmware updates be sure to connect your FLIR FX camera to a power source usingthe included USB cable and power adapter.

#LX400067; r.27354/27358; en-US 5

Optimizing Wi-Fi performance4

Follow the steps below to get the best possible performance from your FLIR FX camera.

Router and camera placement

The most important factor affecting the performance of your FLIR FX camera is theplacement of the router and camera. Install your router in an open space and as high offthe floor as possible.

The closer the camera is installed to the router, the stronger the Wi-Fi signal will be.However, obstructions between the camera and router are often more of a factor thandistance. Minimize the number of walls or other objects the signal must pass through. Inthe drawing below, the camera placed further away from the router can perform just aswell as the camera that is located indoors since there is a line-of-sight connection.

Materials such as metal, brick, and concrete can significantly reduce the signal strength.Plants and trees contain water in the leaves, which can also reduce signal strength.

When Signal Passes Through Signal Strength Lost

Plaster & Wood 10–30%

Brick 30–50%

Concrete Cinder Blocks 50–70%

Metal & Metal Cladding 70–100%

Other wireless devices may also impact performance. It is recommended to have yourrouter and camera placed as far away as possible from cordless phones, microwaves,and any other wireless devices you may own.

If it is not possible to move your router to an optimal position, consider purchasing a Wi-Fi extender. AWi-Fi extender connects to your existing Wi-Fi network and repeats thesignal from a second location.

Testing Wi-Fi signal strength

Your smartphone or tablet may have a visual indicator of the strength of your Wi-Fi signalin the notification area. It is recommended to place the camera in an area that shows afull signal.

#LX400067; r.27354/27358; en-US 6

Optimizing Wi-Fi performance4

Testing connection speed

A slow connection may also affect the performance of your FLIR FX camera. It is recom-mended to have an upload speed of at least 1Mbps or higher per camera. You can checkwith your Internet Service Provider or a third party website like speedtest.net to checkyour connection speed.

#LX400067; r.27354/27358; en-US 7

How to set up your FLIR FXcamera

5

5.1 FLIR FX Android™ setup

1. Download the FLIR FX app from the Google Play Store.2. Connect the included USB cable to the power adapter. Connect the other end of the

USB cable to the camera or the camera stand and connect the power adapter to apower outlet.

NOTE

• The REC LED located on the top of the camera will glow orange indicating the camera is charg-ing. It will glow green when the camera is finished charging. The battery will take 6 hours to fullycharge.

• You can connect the power adapter and USB cable to the camera or camera stand. Do not con-nect a USB cable to both the camera and stand at the same time.

3. The camera will turn on automatically when the power is connected and the RECLED will turn on. If camera does not turn on, press the power button to turn on thecamera.

#LX400067; r.27354/27358; en-US 8

How to set up your FLIR FX camera5

4. Open the app and tap New User to create a new account or tap Existing User if youalready have an account (for example, if you bought the camera from the FLIRwebsite).

5. If a you are new user, enter your email address and password then tap Sign Up.

#LX400067; r.27354/27358; en-US 9


6. Tap Add your first camera.

7. Select either Indoor or Outdoor, depending on your camera type.

#LX400067; r.27354/27358; en-US 10


8. Charge your camera for at least 20 minutes before continuing the setup then tapContinue.

9. Scan your camera’s QR code, which is located on the bottom of the indoor stand. Or,

tap to manually enter the number beneath the QR code.

#LX400067; r.27354/27358; en-US 11


10.Wait for the app to automatically connect your smartphone to the camera’s Wi-Finetwork.

NOTE

In some cases, the app may not be able to connect your phone to the camera’s Wi-Fi network. Tocontinue the setup, you will need to select the color of the LED on the back of the camera. You’llthen be prompted to connect your phone to the camera’s Wi-Fi network (the network will have aname similar to “FX-fxvdb30b2744”).

NOTE

If you are using the outdoor camera, the app will prompt you to remove the camera from the out-door housing to check the LED color.

#LX400067; r.27354/27358; en-US 12


11. Give your camera a name and password and press Set. The camera name can beanything you want, such as the location of the camera (e.g., “Front Door”) or how thecamera will be used (e.g., “Sports Camera”).

12. Select the appropriate Wi-Fi network from the list. Enter the password for your Wi-Finetwork and tap Connect.

#LX400067; r.27354/27358; en-US 13


13. The LED on the back of the camera flashes while the camera is connecting tothe Wi-Fi network. When it connects, it glows green and the app displays the screenbelow.

14. Tap Done. Select the camera from the camera list to connect to the live video.

NOTE

If you enter the incorrect Wi-Fi password, the camera will attempt to connect to the network for 60

seconds. If it cannot connect within that time, it will return to Direct Mode and the LED will turn

on. Once the LED is glowing, retry the setup.

#LX400067; r.27354/27358; en-US 14


5.2 FLIR FX iPhone® setup

1. Download the FLIR FX app from the App Store.2. Connect the included USB cable to the power adapter. Connect the other end of the

USB cable to the camera or camera stand and connect the power adapter to a poweroutlet.

NOTE

• The REC LED located on the top of the camera will glow orange to indicate the camera is charg-ing. It will glow green when the camera is finished charging. The battery will take 6 hours to fullycharge.

• You can connect the power adapter and USB cable to the camera or camera stand. Do not con-nect a USB cable to both the camera and stand at the same time.

3. The camera will turn on automatically when the power is connected and the RECLED will turn on. If camera does not turn on, press the power button to turn on thecamera.

#LX400067; r.27354/27358; en-US 15


4. Open the app and tap New User to create a new account or tap Existing User if youalready have an account (for example, if you bought the camera from the FLIRwebsite).

5. If a you are new user, enter your email address and password and tap Sign Up.

#LX400067; r.27354/27358; en-US 16




#LX400067; r.27354/27358; en-US 17




press to manually enter the number beneath the QR code.

#LX400067; r.27354/27358; en-US 18


10. Check the LEDs on the back of the camera. If the LED is glowing, select SteadyOrange.

NOTE


11. After selecting , tap the Home button . Open the Settings menu and connectyour iPhone® to the Wi-Fi network created by the camera.

#LX400067; r.27354/27358; en-US 19


12. Tap the Home button twice to exit the Settings menu and return to the FLIR FXapp. The app will connect to your camera's Wi-Fi network.


14. Select your Wi-Fi network from the list. Enter the password for your Wi-Fi networkand tap Connect.

#LX400067; r.27354/27358; en-US 20


15. The LED on the camera will flash while the camera is connecting to the Wi-Finetwork. When it finishes connecting, it will glow green and the app will show thescreen below.

16. Tap Done. Tap on the camera in the camera list to connect.

NOTE

If you enter the wrong Wi-Fi password, the camera will attempt to connect to the network for 60 sec-

onds. If it cannot connect within that time it will return to Direct Mode and the LED will turn on.

Once the LED is glowing, retry the setup.

#LX400067; r.27354/27358; en-US 21


5.3 FLIR FX Android™ tablet setup

1. Download the FLIR FX app from the Google Play Store.2. Connect the included USB cable to the power adapter. Connect the other end of the

USB cable to the camera or camera stand and connect the power adapter to a poweroutlet.

NOTE

• The REC LED located on top of the camera will glow orange to indicate the camera is charging.It will glow green when the camera is finished charging. The battery will take 6 hours to fullycharge.

• You can connect the power adapter to either the USB port on the camera or camera stand. Donot connect a USB cable to both the camera and the stand at the same time.

3. The camera will turn on automatically when the power is connected and the RECLED will turn on. If the camera does not turn on, press the power button to turn on thecamera

#LX400067; r.27354/27358; en-US 22


4. Open the app. Tap New User to create a new account or tap Existing User if you al-ready have an account (for example, if you bought the camera from the FLIRwebsite).


#LX400067; r.27354/27358; en-US 23




#LX400067; r.27354/27358; en-US 24




press to manually enter the number beneath the QR code.

#LX400067; r.27354/27358; en-US 25


10.Wait for the app to automatically connect your smartphone or tablet to the Wi-Fi net-work created by the camera.

NOTE

In some cases, the app may not be able to connect your phone to the camera's Wi-Fi network. Tocontinue setup, you will need to select the color of the LED on the back of camera. Then connectyour Android device to the camera's Wi-Fi network (will look something like "FX-fxvdb30b2744").


#LX400067; r.27354/27358; en-US 26



13. The LED will flash while the camera is connecting to the Wi-Fi network. When itfinishes connecting, it will glow green and the app will display the screen below.

14. Tap Done. Tap on the camera in the camera list to connect to the video.

NOTE


onds. If it cannot connect within that time, it will return to Direct Mode and the LED will turn on.


#LX400067; r.27354/27358; en-US 27


5.4 FLIR FX iPad® setup

1. Download the FLIR FX app from the App Store.2. Connect the included USB cable to the power adapter. Connect the other end of the

USB cable to the camera and connect the power adapter to a power outlet.

NOTE

• The REC LED will glow orange to indicate the camera is charging. It will glow green when thecamera is finished charging. The battery will take 6 hours to fully charge.

• You can connect the power adapter to either the USB port on the camera or camera stand. Donot connect a USB cable to both the camera and the stand at the same time.

3. Camera turns on automatically when power is connected and REC light will turn on. Ifcamera does not turn on, press the power button to turn on the camera. The camera

will start up and the LED on the back of the camera will glow orange.

#LX400067; r.27354/27358; en-US 28


4. Open the app. Tap New User to create a new account or tap Existing User if you al-ready have an account (for example, if you bought the camera from the FLIRwebsite).


#LX400067; r.27354/27358; en-US 29




#LX400067; r.27354/27358; en-US 30



9. Scan your camera’s QR code, which is located on the bottom of the indoor stand. Al-

ternatively, press to manually enter the number beneath the QR code.

#LX400067; r.27354/27358; en-US 31


10. Check the LEDs on the back of the camera. If the LED is glowing, press SteadyOrange.

NOTE


11. After selecting , tap the Home button . Open the Settings menu and connectyour iPad® to the Wi-Fi network created by the camera.

NOTE

The network will be listed similarly to something like "FX-litfcce54fc4".

#LX400067; r.27354/27358; en-US 32


12. Tap the Home button twice to exit the Settings menu and return to the FLIR FXapp. The app will connect to your camera's Wi-Fi network.



#LX400067; r.27354/27358; en-US 33


15. The LED will flash while the camera is connecting to the Wi-Fi network. When itfinishes connecting, it will glow green and the app will display the screen below.

16. Tap Done. Tap on the camera in the camera list to connect.

NOTE


onds. If it cannot connect within that time it will return to Direct Mode and the LED will turn on.


#LX400067; r.27354/27358; en-US 34

Connect to your camera in DirectMode

6

Direct Mode lets you connect to the camera and view live video even in areas without aWi-Fi signal. Direct Mode uses the built-in Wi-Fi access point in the camera to create aWi-Fi hotspot.

To connect to your camera using Direct Mode:

1. Press and hold the Wi-Fi button on the camera for 1 second. The Direct Mode

LED on the back of the camera will glow solid orange once Direct Mode is ready.

#LX400067; r.27354/27358; en-US 35

Connect to your camera in Direct Mode6

2. Navigate to Settings on your smartphone or tablet. Select the Wi-Fi network createdby your camera. The network name will be in the format "FX-Camera-name". For ex-ample, if you’ve manually changed your camera's name to Driveway, the networkname will be FX-Driveway.

NOTE

The screen above may differ depending on the model of smartphone or tablet that you have.

#LX400067; r.27354/27358; en-US 36

Connect to your camera in Direct Mode6

3. Open the FLIR FX app. If using a smartphone, tap the camera to connect in DirectMode. If using a tablet, the app will automatically connect to the camera.

NOTE

Direct Mode will only enable you to connect to your FLIR FX camera. While connected to your cam-era in Direct Mode, you will not be able to connect your smartphone or tablet to the Internet.

If you are having issues connecting to your camera in Direct Mode

If you are not able to connect to the camera in Direct Mode, check the LED indicators onthe back of the camera:

Cloud Mode LED is on: Camera is in Cloud Mode. Press and hold the Wi-Fi but-

ton on the camera for 1 second to change to Direct Mode.

Direct Mode LED is flashing: Camera is still restarting. Wait for the LED to stopflashing.

Direct Mode LED is glowing: Check the following on your smartphone or tablet:

• Make sure your device has Wi-Fi enabled and is within range of the camera.• Make sure you are connected to the Wi-Fi network created by your camera. The net-work name will look like "FX-Camera-name".

• Close the FLIR FX app and restart it to refresh the camera list.

#LX400067; r.27354/27358; en-US 37

Connect to your camera in CloudMode

7

Cloud Mode enables you to connect to your camera from anywhere in the world over theInternet. When in Cloud Mode, up to three devices can be connected to the camera atthe same time.

Prerequisite(s):

• Complete the initial setup of the camera to add it to your account and connect it toyour Wi-Fi network.

Connect to your camera in Cloud Mode (smartphones):

1. Open the FLIR FX app.2. Tap the camera in your camera list to connect in Cloud Mode.

#LX400067; r.27354/27358; en-US 38

Connect to your camera in Cloud Mode7

Connect to your camera in Cloud Mode (tablets):

1. Open the FLIR FX app.2. Tap and drag the desired camera into one of the four viewing areas. You can view up

to four cameras at the same time.

NOTE

The DEVICES list on tablet interfaces can be swiped from the left of the screen to open new cam-eras. Alternatively, the opened DEVICES list can be swiped back to the left to hide it.

If you are having issues connecting to your camera in Cloud Mode

If you are not able to connect to the camera in Cloud Mode, check the LED indicators onthe back of the camera:

Direct Mode LED is flashing or glowing: Camera is in Direct Mode. Press the Wi-

Fi button on the camera to change to Cloud Mode.

#LX400067; r.27354/27358; en-US 39

Connect to your camera in Cloud Mode7

Cloud Mode LED is flashing:

This indicates the camera is attempting to connect to the FLIR Cloud servers. Once theconnection is successful, it will stop flashing and glow solidly. If the Cloud Mode LED isstill flashing after 20 seconds, check the following:

• Camera may not be in range of your Wi-Fi router. Move the camera closer to your Wi-Fi router.

• Camera may be connected to the wrong Wi-Fi network, it may have the wrong Wi-Fipassword saved, or the Wi-Fi password may have changed.

• Wi-Fi network may have MAC address filtering enabled. If so, you will need to add thecamera's MAC address to your Wi-Fi router's list of accepted devices. Check yourrouter's user guide for details.

• The Wi-Fi network the camera is connected to may not have access to the Internet.Contact your Internet service provider if you think the issue is related to your Internetservice.

Cloud Mode LED is on:

This indicates the camera is successfully connected to the FLIR Cloud servers. Checkthe following on your smartphone or tablet:

• Make sure you are not connected to a Wi-Fi network created by another camera thatis in Direct Mode.

• Check the upload speed on your home Internet connection. It is recommended tohave a high-speed Internet service with an upload speed of 1Mpbs or higher. A slowInternet connection may prevent the camera from getting connected.

• Close the FLIR FX app and then re-open it.

#LX400067; r.27354/27358; en-US 40

How to mount your FLIR FXcamera

8

Instructions on how to wall mount your camera depend on whether you have an indoorcamera (for example FXV101-H) or outdoor camera (FXV101-W or FXAW01 accessory).

Mounting the indoor camera

The indoor stand allows you to simply mount the camera to a wall. An extra mountingplate is provided so you can have a permanent mounting place for the camera while stillbeing able to move the camera around when needed.

Before mounting the camera, determine the best mounting position to get a view of thearea you want. Ensure the power cable is long enough to power the camera.

CAUTION

Keep the cables at least 3ft / 1m away from baby cribs and out of reach of children and infants. Use theincluded cable clips to help manage the cables.

How to install an indoor camera

1. Using a coin, turn the mounting plate on the bottom of the indoor stand counter-clockwise to remove it from the base.

#LX400067; r.27354/27358; en-US 41

How to mount your FLIR FX camera8

2. Use a pencil to mark holes for the mounting screws.

3. Drill holes where marked using a drill. Tap the included anchors into the holes gentlyusing a hammer. Attach the mounting plate to the wall using the included mountingscrews.

4. Attach the camera stand to the mounting plate. Make sure the locking mechanism onthe plate lines up with the indent in the camera stand. Twist the camera stand clock-wise to secure it to the mounting plate.

#LX400067; r.27354/27358; en-US 42


How to install an outdoor camera

The outdoor housing allows you to install the camera to a wall or ceiling both indoors andoutdoors. Before permanently installing the camera, it is recommended to complete thesetup using the FLIR FX app to connect the camera to your Wi-Fi network.

It is also a good idea to install the camera in an area with a strong Wi-Fi signal from yourrouter. You can check the Wi-Fi signal using the signal indicator on your smartphone ortablet.

CAUTION

If you are installing the camera outdoors, you must connect the power adapter to a sheltered poweroutlet.

1. Use the included mounting template to drill holes on your wall or ceiling.

2. Gently tap the included anchors into the holes using a hammer.3. Secure the mount to the wall or ceiling using the included mounting screws.

#LX400067; r.27354/27358; en-US 43


4. Adjust the camera position.

1. Loosen adjustment ring to adjust the horizontal position.

2. Use the included Allen key to adjust the vertical position.

3. Use the included Allen key to twist the camera on the stand.

5. Make sure to fully tighten the adjustment screws after setting the position.6. Connect the camera to the included power adapter and connect the power adapter

to a power outlet.

NOTE

Make sure the power connector and power outlets are protected from the elements when installing.

#LX400067; r.27354/27358; en-US 44


7. Remove the protective film from the lens cover after you have finished installation.

#LX400067; r.27354/27358; en-US 45

How to mount your FLIR FXcamera to your windshield

9

The FLIR FX dash mount stand (FXAD01, sold separately) adds additional functionalityto your FLIR FX camera.

1. Attach your FLIR FX camera to the windshield mount by sliding the camera along themount’s accessory connector.

2. Release the lever to unlock the suction cup.

#LX400067; r.27354/27358; en-US 46

How to mount your FLIR FX camera to your windshield9

3. Position the suction cup against the windshield and press lever towards the base tolock the suction cup.

4. Connect one end of the USB cable to the camera and the other to the car charger.Connect the car charger to the cigarette lighter.

#LX400067; r.27354/27358; en-US 47

Using your FLIR FX camera witha sports case

10

Sports camera setup

The sports case accessory (FXAS01, sold separately) protects your FLIR FX camerafrom water and dust. Since it will not be possible to charge the battery while the camerais in the sports case, it is recommended the camera should be charged at least 2–3hours before installing it in the sports case to maximize operating/recording time.

To put the camera in the sports case:

1. Slide the open button and pull the latch open from behind the triangle to open thelatch.

2. Place the camera inside the case with the FLIR logo facing the opening.

3. Close the case and push the latch forward to lock it.

NOTE

• Always secure the camera in the sports case when using the FLIR FX around water. Failure toproperly lock the sports case can result in leaks that may damage or destroy your camera.

• Be sure to keep the sports case free from any dust / dirt that may collect during use.

#LX400067; r.27354/27358; en-US 48

Using your FLIR FX camera with a sports case10

4. To mount the camera, screw the case onto the included 3M surface mount and peelthe adhesive to stick the camera to different objects.

NOTE

You can also use standard 1/4”- 20 camera tripods or accessories to mount the camera in thesports case. You can swap the ball and socket stand between mounts. To remove the ball andsocket, unscrew the thumbscrew all the way and pull the ball and socket from the mount.

#LX400067; r.27354/27358; en-US 49


Sports case overview

1. Record Button: Press to take a photo. Hold to start and stop video recording.

2. Lens Cover: Clean the lens cover with a damp cloth. Do not use harsh or chemicalcleaners to clean the lens cover as they can damage the plastic.

3.Microphone: Not used when camera is in sports case.

4. Speaker: Not used when camera is in sports case.

5. Thread: Attach the sports case to the included 3M surface mount. Also works withstandard 1/4”-20 compatible tripods or accessories.

6.Wi-Fi Button: Use to toggle between Cloud and Direct Mode. Press and hold for fiveseconds to turn off Wi-Fi for increased battery life. Press for one second to turn Wi-Fiback on.

7. Power Button: Press the power button to turn on the camera. Press and hold to turnoff the camera.

#LX400067; r.27354/27358; en-US 50


8.MicroSD (on camera): Store even more with an 8GB to 64GB microSD card. Class10 card required.

9.MicroUSB (on camera): Easily recharge your FLIR FX camera.

10. Latch: Open and close the sport case. Make sure the case is completely locked toensure a waterproof seal.

11. Direct Mode LED: View live video or recordings on the microSD card directly fromyour FLIR FX camera without an Internet connection. Live video is disabled while thecamera records.

12. Cloud Mode LED: Flashes when the camera is attempting to connect to a Wi-Fi net-work, glows when the camera is connected to a Wi-Fi network.

#LX400067; r.27354/27358; en-US 51


13. Surface Mount: Enables the camera to attach to a surface for sporting activities.

14. Thumbscrew: Tighten to secure the camera position. Loosen to remove ball andsocket from stand.

15. 3M Adhesive: Peel to stick the mount to a surface.

#LX400067; r.27354/27358; en-US 52

Viewing your FLIR FX camera inhigh definition

11

The default resolution for viewing the camera on a smartphone or tablet is standard defi-nition (WVGA). You can increase the resolution to high-definition 720p (1280x720) usingthe app.

NOTE

If your Internet upload speed is too low, selecting High Definition may affect your ability to connect tothe camera. It is recommended to use Standard Definition unless you have an upload speed above1Mbps.

To switch the live view resolution (smartphones):

1. Tap on the camera in the camera list to connect to the live video stream.

2. Tap the gear icon to open the settings menu.

#LX400067; r.27354/27358; en-US 53

Viewing your FLIR FX camera in high definition11

3. Scroll down to Video quality. Tap to select High Definition (720p) or Standard Def-inition (WVGA).

4. Tap Save.

To switch live view resolution (tablets):

1. Tap and drag the desired camera into one of the four viewing areas. You can view upto four cameras at the same time.

#LX400067; r.27354/27358; en-US 54

Viewing your FLIR FX camera in high definition11


3. Use the Resolution slider to select SD (WVGA) or HD (720p).

4. Tap Save.

#LX400067; r.27354/27358; en-US 55

How to change the name of yourcamera

12

The Camera name is the name given to your cameras in your Camera list. It can be any-thing you choose, such as the location of the camera (e.g., “Front Door”) or how the cam-era will be used (e.g., “Dashboard Camera”). You can change the camera name usingthe FLIR FX app.

To change the Camera name (smartphones):



#LX400067; r.27354/27358; en-US 56

How to change the name of your camera12

3. Enter the new Camera name you would like to use.

4. Tap Save.

To change the Camera name (tablets):


#LX400067; r.27354/27358; en-US 57

How to change the name of your camera12


3. Tap Camera details. Enter the new Camera name you would like to use.

4. Tap Save.

#LX400067; r.27354/27358; en-US 58

How to change your camera’spassword

13

The camera password is saved in the app, so you only need to enter it the first time youare connecting to the camera on a smartphone or tablet. You will need to enter the cam-era password again if you connect to the camera on a new smartphone or tablet. It is rec-ommended to write down the camera password or save it to a note taking app such asEvernote.

NOTE

If you want to give access to your camera to a friend, you can give them the camera ID (printed belowthe QR code) and password. They can then connect using the app as a guest user to view live video.Only the camera owner can view recordings or change camera settings.

To change the camera password (smartphones):



#LX400067; r.27354/27358; en-US 59

How to change your camera’s password13

3. Enter the new Camera name you would like to use.

4. Tap Save. When connecting with a different smartphone or tablet, you will beprompted to enter the new camera password.

To change the camera password (tablets):


#LX400067; r.27354/27358; en-US 60



3. Tap Camera details. Enter the new Password you would like to use.

4. Tap Save.

#LX400067; r.27354/27358; en-US 61


What to do if you forget your camera’s password

To reset the camera password (smartphones):

1. Press and hold the Wi-Fi and REC buttons on the camera at the same time untilthe camera beeps three times. This resets the camera to factory defaults.

2. Go to the Settings app on your smartphone or tablet and select the Wi-Fi networkcreated by your camera. The network name will be in the format "FX-Camera-ID". Itwill appear something like: "FX-fxvdb30b2744".

#LX400067; r.27354/27358; en-US 62


3. Open the FLIR FX app. It will detect your camera has been reset. Press Setup Cam-era to continue.

4. Select Steady Orange.

#LX400067; r.27354/27358; en-US 63


5. Enter a new Camera name and Password for your camera and then tap Set.

6. Select your Wi-Fi network from the list and then enter the password for your Wi-Fi

network. The camera will connect to the new Wi-Fi network. The LED will glowwhen it has successfully connected.

NOTE

If the camera cannot connect to the network after 60 seconds because the password was incorrect

or the router is out of range, the camera will return to Direct Mode. After the LED turns on, re-peat the steps above starting from step 1.

7. Tap Done to finish the password reset process. You can now connect to your cameraover the Internet on your smartphone or tablet.

#LX400067; r.27354/27358; en-US 64


To reset the camera password (tablets):

1. Press and hold the Wi-Fi and REC buttons on the camera at the same time untilthe camera beeps three times. This resets the camera to factory defaults.

2. Go to the Settings app on your smartphone or tablet and select the Wi-Fi networkcreated by your camera. The network name will be in the format "FX-Camera-ID". Itwill appear something like: "FX-fxvdb30b2744".

#LX400067; r.27354/27358; en-US 65


3. Open the FLIR FX app. It will detect your camera has been reset. Press Setup Cam-era to continue.

4. From the available options, select Steady Orange.5. Enter a new Camera name and Password for your camera and then tap Set.

#LX400067; r.27354/27358; en-US 66


6. Select your Wi-Fi network from the list and then enter the password for your Wi-Fi

network. The camera will connect to the new Wi-Fi network. The LED will glowwhen it is successfully connected.

NOTE

If the camera cannot connect to the network after 60 seconds because the password entered was

incorrect or the router is out of range, the camera will return to Direct Mode. After the LEDturns on, repeat the steps above starting from step 1.

7. Tap Done to finish the password reset process. You can now connect to your cameraover the Internet on your smartphone or tablet.

#LX400067; r.27354/27358; en-US 67

Setting temperature andhumidity alerts

14

The FLIR FX app can send you push notifications if the temperature or humidity near thecamera goes outside of a specified range. To use these features, you must install thecamera in a stand that includes the appropriate sensors. The indoor stand includes atemperature and humidity sensor. The outdoor stand includes a temperature sensor only.

NOTE

• If you place your camera in a location where it will come into contact with direct sunlight (i.e., windowsill) it will record a temperature reading approximately 10 °C higher than the ambient roomtemperature.

• When your camera is plugged into a power source the temperature reading may be approximately4–5 °C higher than the ambient room temperature.

To set up temperature and humidity alerts and recording (smartphone):



#LX400067; r.27354/27358; en-US 68

Setting temperature and humidity alerts14

3. Scroll down to the Automatic recording triggers section. Check Automatic Record-

ing Triggers. Tap to activate temperature alerts.

4. Tap °F or °C to switch between Fahrenheit and Celsius.5. Adjust the slider to select the normal temperature range for the camera. When the

temperature goes above or below this range, you receive a notification.

6. Tap to activate humidity alerts. Use the slider to adjust the normal humidity rangefor the camera. When the humidity goes outside of this range, you will receive anotification.

7. Tap Save at the top of the settings menu to save your changes.

#LX400067; r.27354/27358; en-US 69


To set up temperature and humidity alerts and recording (tablets):



3. Tap Automatic triggers.

#LX400067; r.27354/27358; en-US 70


4. Check Automatic Recording Triggers. Tap to activate temperature alerts.

5. Tap °F or °C to alternate between Fahrenheit and Celsius.6. Adjust the slider to select the normal temperature range for the camera. When the

temperature goes above or below this range you will receive a notification.

7. Tap to activate humidity alerts. Use the slider to adjust the normal humidity rangefor the camera. When the humidity goes outside of this range you will receive anotification.


#LX400067; r.27354/27358; en-US 71

How to control the camera’snight vision LEDs

15

By default, night vision is enabled when there is insufficient light in the immediate envi-ronment. Using the FLIR FX app, you can set when the night vision turns on or disablethe feature entirely. This can be useful in certain low light conditions where you wouldn’twant the night vision to turn on automatically. For instance, when aiming the camerathrough a window, disabling the night vision feature eliminates any reflection caused bythe IR LEDs.

To control the night vision LEDs (smartphones):


#LX400067; r.27354/27358; en-US 72

How to control the camera’s night vision LEDs15


3. Scroll to the Night Vision section and tap to select Automatic. Doing so will ena-

ble the night vision LEDs to automatically turn on in low light conditions. Tappingwhen the feature is enabled will disable the night vision.

NOTE

The camera emits a clicking noise when switching between day and night modes. This indicatesthat the IR filter is working properly.

4. Tap Save.

#LX400067; r.27354/27358; en-US 73


To control the night vision LEDs (tablets):



#LX400067; r.27354/27358; en-US 74


3. Select Configuration. Tap to select Automatic. Doing so will enable the night

vision LEDs to automatically turn on in low light conditions. Tapping when thefeature is enabled will disable the night vision.

NOTE

The camera emits a clicking noise when switching between day and night modes. This indicatesthat the IR filter is working properly.

4. Tap Save.

#LX400067; r.27354/27358; en-US 75

Manual recording16

While the camera is on, press the REC button on the top of the camera. The button willbegin flashing red to indicate recording is in progress. Press the REC button again tostop recording.

#LX400067; r.27354/27358; en-US 76

Setting motion detection alertsand recording

17

Your FLIR FX camera can be set to record when motion is detected. You will receive apush notification on your smartphone or tablet when one of your cameras detects motion.Motion detection recording must be activated in order to use the FLIR Recap; a featurethat analyzes motion recordings to provide a detailed summary of detection events.

You can also set Smart Zones™. Smart Zones allow you to enable motion detection inimportant areas such as entryways or your driveway. You can disable motion detection inareas where there is constant motion, such as a busy street.

To set up motion detection alerts and recording (smartphones):



#LX400067; r.27354/27358; en-US 77

Setting motion detection alerts and recording17


ing Triggers. Tap to activate motion detection recording and alerts. The icon willglow green when motion detection is activated.

4. Use the slider to adjust the sensitivity. Low sensitivity means more motion is requiredto trigger an event. High sensitivity means less motion is required to trigger an event.

5. Tap to configure SmartZone. SmartZone allows you to receive alerts when mo-tion is detected in high priority areas and disable motion alerts in areas of lessimportance.

#LX400067; r.27354/27358; en-US 78


6. A grid overlay opens over the video. By default, the entire video area is enabled formotion detection. To configure SmartZone:

• Tap inside the grid to configure. Activated areas will turn blue.• Tap Clear to reset SmartZones to the default setting (motion activatedeverywhere).

• Tap Cancel to exit with no changes.• Tap Save to save settings and return to the settings menu.


To set up motion detection alerts and recording (tablets):


#LX400067; r.27354/27358; en-US 79




ing Triggers. Tap to activate motion detection recording and alerts. The icon willglow green when motion detection is activated.

4. Use the slider to adjust the sensitivity. Low sensitivity means more motion is requiredto trigger an event. High sensitivity means less motion is required to trigger an event.

#LX400067; r.27354/27358; en-US 80


5. Tap to configure the SmartZone feature. SmartZone allows you to only receivealerts when motion occurs in the areas that matter most to you as well as disablealerts in other areas.

6. A grid overlay opens over the video. By default, the entire video area is enabled formotion detection. To configure SmartZone:

• Tap inside the grid to configure. Activated areas will turn blue.• Tap Clear to reset SmartZones to the default setting (motion detection activatedeverywhere).

• Tap Cancel to exit with no changes.• Tap Save to save settings and return to the settings menu.


#LX400067; r.27354/27358; en-US 81

Setting sound alerts andrecording

18

Your camera can detect the volume of sounds in a room. Like the motion detection fea-ture, if the volume of sound exceeds the specified sensitivity level, it will record and senda notification to your smartphone or tablet. This is particularly useful if you want to useyour camera as a baby or child monitor, as it can alert you when your child wakes up froma nap.

To set up sound alerts and recording (smartphones):




ing Triggers. Tap to activate sound alerts.

#LX400067; r.27354/27358; en-US 82

Setting sound alerts and recording18

4. Use the slider to select the audio sensitivity level for the camera.


To set up sound alerts and recording (tablets):


#LX400067; r.27354/27358; en-US 83

Setting sound alerts and recording18


3. Tap Automatic Triggers.

4. Check Automatic Recording Triggers. Tap to activate sound alerts. Use theslider to select the audio sensitivity level for the camera.


#LX400067; r.27354/27358; en-US 84

Viewing recordings via the FLIRFX app

19

You can view manual recordings, automatic (triggered recordings), and FLIR Recaps™on the FLIR FX app. You can also share them with friends and family using social mediasites like YouTube or Facebook.

Available recording types include:

• Manual: Manual recordings are created when you press and hold the RECbutton on the camera. The REC button will flash red while recording is in progress.

• Automatic: Automatic recordings are triggered by events like motion detection.

• Photo: Photos can be taken by manually pressing (and holding) the REC but-ton for one second.

• Rapid Recap: A Rapid Recap™ summarizes motion detection recordings in oneshort clip.

To view video recordings (smartphones):

1. Tap in live view of from the camera list to open the camera’s playback menu.

2. Select one of the recording types listed above, and then tap one of the recording

events to begin viewing.

#LX400067; r.27354/27358; en-US 85

Viewing recordings via the FLIR FX app19

Playback controls:

The playback controls for recordings are shown below.

1. Back: Tap to return to your recordings list.2. Share: Tap to share the video file (icon may appear differently depending on your

device).3. Time-line: Drag to fast forward or rewind.4. Trigger: Shows the type of event that triggered the recording.5. Time-stamp.

To view recordings (tablets):


#LX400067; r.27354/27358; en-US 86

Viewing recordings via the FLIR FX app19

2. Tap Recordings to open the list of recordings.

Playback controls

The playback controls for recordings are shown below.

1. Back: Tap to return to your recordings list.2. Video file: Tap to select a video file. Shows the date and time the file was recorded

as well as the recording trigger.3. Share: Tap to share the video file.4. Categories: Tap to browse different recording types.5. Full-screen: Tap to view recording in full screen.6. Time-line: Drag to fast forward or rewind.

#LX400067; r.27354/27358; en-US 87

How to create a Rapid Recap™20

Rapid Recap™ gives you a summary of all the motion events that your camera has de-tected over a predetermined period of time. The summary lists each occurrence of peo-ple and objects that passed in front of the camera. Also, a Rapid Recap allows you toview one-minute summary videos recapping the day’s motion events.

Prerequisites:

• You must activate motion recording before you can order a Rapid Recap. See17 Set-ting motion detection alerts and recording, page 77 for details. We recommend thatyou let the camera record for a minimum of 3 hours before creating a Rapid Recap.

To create a Rapid Recap (smartphones):


#LX400067; r.27354/27358; en-US 88


2. Tap the Actions button and then tap Rapid Recap.

3. Select the start time and end time for your Rapid Recap.

• Select the day at the top of the screen.• To move the entire time range, drag anywhere on the screen.• Tap and drag on the start and end time to select the start and end time of the Rap-id Recap.

4. Press Create to confirm the time range and order the recap.

#LX400067; r.27354/27358; en-US 89


5. The app returns to live view and starts creating your recap. Creating a recap may takeup to 10 minutes while our servers process the video. You will get a notification whenit is ready.

To create a Rapid Recap (tablet):


#LX400067; r.27354/27358; en-US 90


2. Tap Rapid Recap.

3. Select the start time and end time for your Rapid Recap.

4. Press Create to confirm the time range and order the recap.5. The app returns to live view and starts creating your recap. Creating a recap may take

up to 10 minutes while our servers process the video. You will get a notification whenit is ready.

#LX400067; r.27354/27358; en-US 91

How to view a Rapid Recap21

Rapid Recap™ gives you a summary of all the motion events that your camera has de-tected for a predetermined period of time. The summary lists each occurrence of peopleand objects that passed in front of the camera. Also, it allows you to view one minutesummary videos recapping the day’s motion events.

Prerequisites:

• Create a Rapid Recap. See 20 How to create a Rapid Recap™, page 88• You must activate motion recording before you can create a Rapid Recap. See 17 Set-ting motion detection alerts and recording, page 77.

To view a Rapid Recap (smartphones):

1. Tap in live view or from the camera list to open up the playback menu for thecamera.

2. Tap Rapid Recap to view recaps you have saved for this camera. Select one of therecaps to view by tapping it in the recaps list.

#LX400067; r.27354/27358; en-US 92


Rapid Recap playback controls:

1. Back: Return to your list of recordings.2. Time-line: Shows the start and end times of the selected Rapid Recap. The green

highlighted area shows the time range for the current chapter.3. Chapter: Press the play button to view the summary video for the currently selected

chapter. The summary video will show you all the objects that moved in the scene ina short video clip. Press the left and right areas to jump to the next or previouschapter.

4. Objects: The bottom of the screen shows a list of all the objects within the Rapid Re-cap and the time that each object was detected. You can drag left or right to scanthrough the objects, or tap on a specific object to view the original recording where itwas detected.

To view a Rapid Recap (tablets):


#LX400067; r.27354/27358; en-US 93


2. Tap Recordings to open the recording list.

3. Tap Rapid Recap to view recaps.

#LX400067; r.27354/27358; en-US 94


Rapid Recap playback controls:

1. Back: Return to live view.2. Recaps: List of recaps for the selected camera. Shows the time range, number of ob-

jects and chapters in the recap.3. Recording types: Tap to select a different recording type.4. Time-line: Shows the start and end times of the selected Rapid Recap. The green

highlighted area shows the time range for the current chapter.5. Chapter: Press the play button to view the summary video for the currently selected

chapter. The summary video will show you all the objects that moved in the scene ina short video clip.

6. Arrow: Tap the arrows to select chapter.7. Objects: The bottom of the screen shows a list of all the objects within the Rapid Re-

cap and the time that each object was detected. You can drag left or right to scanthrough the objects, or tap on a specific object to view the original recording where itwas detected.

#LX400067; r.27354/27358; en-US 95

How to view recordings on acomputer

22

The easiest way to view video recordings from your FLIR FX camera on a computer is toconnect the camera directly to the computer using the included microUSB cable. If yourcomputer has an SD or microSD card reader, you can use it to view the recordings.

NOTE

This section covers local recordings saved to the camera’s microSD card only. If you have a subscrip-tion plan and have recordings saved in the cloud, you will need to use the FLIR FX app to view those re-cordings. See 19 Viewing recordings via the FLIR FX app, page 85

To view video recordings from the camera microSD card on a computer runningWindows:

1. Connect a microUSB cable to the camera and connect the large end to a USB porton your computer. This puts the camera into USB storage mode.

NOTE

When the camera is in USB storage mode, you cannot connect to the camera using the apps on asmartphone or tablet. You must disconnect the camera from the computer in order to allowconnectivity.

2. An AutoPlay window appears. Click Open folder to view files.

NOTE

If AutoPlay does not appear, click on My Computer and browse to the SD card. If the SD card doesnot appear, disconnect and reconnect the USB cable to the computer.

#LX400067; r.27354/27358; en-US 96

How to view recordings on a computer22

3. The camera saves videos and images onto the microSD card in folders based on thetype of recording. For example, the USER folder contains manual video recordings.Double-click on the folders to access the video files.

NOTE

The camera saves video files to the microSD card in .mp4 format and saves images in .jpg format.You can view .mp4 videos using Windows Media Player or VLC Player.

To view video recordings from the camera microSD card on a computer runningMac OSX:

1. Connect a microUSB cable to the camera and connect the large end to a USB porton your computer. This puts the camera into USB storage mode.

NOTE

When the camera is in USB storage mode, you cannot connect to the camera using the app on asmartphone or tablet. You must disconnect the camera from the computer in order to allowconnectivity.

2. The camera’s microSD card will show up on the desktop . Double-click SD toopen.

3. The camera saves videos and images onto the microSD card in folders based on thetype of recording. For example, the USER folder contains manual video recordings.Double-click on the folders to access the video files.

NOTE

The camera saves video files to the microSD card in .mp4 format and saves images in .jpg format.You can view .mp4 videos using Quick Time Player or VLC Player.

#LX400067; r.27354/27358; en-US 97

Taking photos using the FLIR FXapp

23

You can use the FLIR FX app to take photos from anywhere in the world. Once taken,you can then share them with family and friends on social media.

To take a photo (smartphones):


2. Tap the Actions button and then tap Snapshot. The camera will take a photo.

#LX400067; r.27354/27358; en-US 98

Taking photos using the FLIR FX app23

3. Select the app you would like to share the photo with. For example, you can email thephoto to a family member or share it on Facebook. The list of apps depends on whichapps you have installed on your phone.

NOTE

If you tap Save Image on iPhone, the photo is saved to your Photos app.

To take a photo (tablets):


2. Tap Snapshot to take a photo.

#LX400067; r.27354/27358; en-US 99

Taking photos using the FLIR FX app23

3. Select the app you would like to share the photo with. For example, you can email thephoto to a family member or share it on Facebook. The list of apps depends on whichapps you have installed on your phone.

NOTE

If you tap Save Image on an iPad, the photo is saved to your Photos app.

#LX400067; r.27354/27358; en-US 100

Using the digital zoom feature24

The digital zoom feature allows you to zoom in on the surveillance area while the camerais in live view.

To use digital zoom (smartphone):


2. Turn your smartphone to landscape mode to enable digital zoom.

3. Pinch outwards to zoom in. Pinch inwards to zoom out. When zoomed in, drag to pan.4. Turn your smartphone to portrait mode to return to normal live viewing.

To use digital zoom (tablet):

1. Open the FLIR FX app.

#LX400067; r.27354/27358; en-US 101

Using the digital zoom feature24


3. Double-tap the camera to view in full screen.

4. Pinch outwards to zoom in. Pinch inwards to zoom out. When zoomed in, drag to pan.

#LX400067; r.27354/27358; en-US 102

Using the intercom25

The intercom feature allows you to transmit your voice through the camera using the mi-crophone on your smartphone or tablet. This feature is particularly useful to communi-cate with people in the camera’s immediate area.

To use the intercom (smartphones):


2. Tap the Actions button.

#LX400067; r.27354/27358; en-US 103


3. Press and hold Intercom. A icon appears on the live video. You can now speakinto the microphone on your smartphone to talk through the camera. There may be adelay when using the intercom while the sound is sent over the Internet.

4. Release the Intercom button to turn off the intercom.

To use the intercom (tablets):


#LX400067; r.27354/27358; en-US 104


2. Press and hold Intercom. A icon appears on the live video. You can now speakinto the microphone on your tablet to talk through the camera. There may be a delaywhen using the intercom while the sound is sent over the Internet.

3. Release the Intercom button to turn off the intercom.

#LX400067; r.27354/27358; en-US 105

Notices26

FCC Notice: This device complies with Part 15, subpart C, of the FCC Rules. Operationis subject to the following two conditions: (1) this device may not cause harmful interfer-ence, and (2) this device must accept any interference received, including interferencethat may cause undesired operation.

The manufacturer is not responsible for any radio or TV interference caused by unauthor-ized modifications to this equipment. Such modifications could void the user’s authorityto operate the equipment. However, it is imperative that the user follows the guidelines inthis manual to avoid improper usage which may result in damage to the unit, electricalshock and fire hazard injury.

Changes or modifications made to this equipment not expressly approved by FLIR Sys-tems, Inc. may void the FCC authorization to operate this equipment.

Radio Frequency Exposure: The radiated output power of the device is below theFCC/ IC radio frequency exposure limits. Nevertheless, the device shall be used in sucha manner that the potential for human contact during normal operation is minimized.

FCC/IC: This device complies with Part 15 of the FCC Rules and with RSS-210 of Indus-try Canada. Operation is subject to the following two conditions: 1. This device may notcause harmful interference, and 2. This device must accept any interference received, in-cluding interference that may cause undesired operation.

Exposition aux radiofréquences : La puissance de sortie rayonnée de l'appareil est in-férieure aux limites d'exposition de radiofréquences de la FCC/IC. Néanmoins, le dispo-sitif doit être utilisé de telle manière que le niveau de contact avec un être humain soitréduit au minimum pendant une utilisation normale.

FCC/IC: Ce dispositif est conforme à la section 15 des réglementations de la FCC et à lanorme RSS-210 d'Industrie Canada. Son fonctionnement est soumis aux deux condi-tions suivantes : 1. Ce dispositif ne doit pas causer d'interférences nuisibles, et 2. Ce dis-positif doit accepter toute interférence reçue, y compris les interférences qui peuventprovoquer un fonctionnement indésirable.

CE: This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption ofconformity with the essential requirements of the R&TTE Directive:

• EMI/EMC Directive 2004/108/EC - Electromagnetic Compatibility• WEEE Directive 2012/19/EU - Waste Electrical and Electronic Equipment• LVD Directive 2006/95/EC - Low Voltage Directive• Battery Directive 2006/66/EC - Batteries and accumulators and waste batteries andaccumulators

• ErP Directive 2009/125/EC - on the Eco-Design requirements of Energy-relatedProducts

• RoHS2 Directive 2011/65/EC - Restriction on the use of certain HazardousSubstances

Disposal: As with most electronic products, this equipment must be disposed of in anenvironmentally friendly way, and in accordance with existing regulations for electronicwaste. Please contact your FLIR Systems, Inc. representative for more details.

Audio Recording: Audio recording without consent is illegal in certain jurisdictions. FLIRSystems, Inc. assumes no liability for use of its products that does not confirm with locallaws.

Need Help

#LX400067; r.27354/27358; en-US 106

Notices26

Visit www.flir.com/fx to access the FLIR FX knowledgebase or contact technical supportor customer service.

#LX400067; r.27354/27358; en-US 107

last page

Publ. No.: LX400067Commit: 27354Head: 27358Language: en-USModified: 2015-07-01Formatted: 2015-07-02

Websitewww.flirsecurity.com/proTechnical Support1-866-816-5919Customer Service1-866-344-4674

Copyright© 2015, FLIR Systems, Inc.All rights reserved worldwide. Names and marks appearing herein are either registered trademarks or trademarks of FLIR Systems and/or its subsidiaries. Allother trademarks, trade names or company names referenced herein are used for identification only and are the property of their respective owners.Legal disclaimerSpecifications subject to change without further notice. Camera models and accessories subject to regional market considerations. License procedures mayapply. Products described herein may be subject to US Export Regulations. Please refer to [email protected] with any questions.

Documents

FLIR FX™ Instruction Manual