Upload
others
View
20
Download
0
Embed Size (px)
Citation preview
Model 200
Blancett is a registered trademark of Racine Federated Inc. Teflon and Viton are registered trademarks of E.I. duPont de Nemours and Company
Flow Meters®
Flow Meters®
Division of Racine Federated Inc.
Positive Displacement Flow MetersB1750
B1750 Positive Displacement Flow Meter
Accuracy of ±0.5% of reading and repeatability of ±0.1%
No need for additional straight run piping
Designed for fluids with a wide range of viscosities, as well as low flow rates
Available in high strength aluminum or stainless steel housing
© 2009 Blancett Printed in USA 10/09 Form No. 1750
Toll Free: 800-235-1638 Tel: 262-639-6770 Fax: 262-417-1155
8635 Washington Avenue, Racine, WI 53406-3738 U.S.A.
E-mail: [email protected]
B1750 Dimensions - Inches (mm)
A20/S20 A60/S60 A80/S80
3.3(84.4)DIA
.47(12)
2.17(55)
1.73(44)
.40(10.2)
.40(10.2)
4.9(125)DIA
.91(23)
3.78(96)
1.61(41)
2.36(60)
1.25(32)2.63
(67)5.50(140)
.63(16)
7.85(199)DIA
5.50(140)
This variable reluctance magnetic pickup coil (B170109) is designed to exceed the performance and application criteria of any standard or modified pickups. Its modular design allows it to be used with the B1750 positive displacement meter, and interface with all Blancett electronics. If using another manufacturer’s electronics with this meter, a Blancett B170210 pre-amplifier may be needed to correctly interface the devices.Output: 30 mV – 3 VAC Sine Wave (B170109) 0-10 V – Square Wave (B170210) 4-20 mA - 3 wire 4-20 mA output (B175420)Connector: 2-pin gold plated type to mate with MS3106-10SL-4S or equivalent (B170109) 3-pin gold plated type to mate with MS3106A-10SL-3S or equivalent (B170210) Temperature: -100 °F to +325 °F (-73 °C to +162 °C) (B170109) -20 °F to +160 °F (-29 °C to +71 °C) (B170210) 0 °F to +185 °F (-18 °C to + 85 °C) (B175420)Materials of Construction: 303/304 stainless steel shell and bottom, solid epoxy encapsulation, standard commercial finish
Note: 80/90 Series utilize Quad-4 Sensor (B170180)
Optional Magnetic PickupUsed with 12, 20, 30 and 60 series only
.51(13)
2.64(67)
3.17(80.4)DIA
4.72(120)DIA
3.15(80)DIA
1.73(44)
3.32(84.4)DIA
A30/S30
1/2"-13 UNC(10 PL)
2.63(67)5.50(140)
1.25(32)
1.61(41)
A90/S90
7.00(178)
7.85(199)DIA
2.00(51)
1.50(38)
SENSOR HOLE(1/2-20 NF)
1/4 NPTPORTS
1.00(26)
.36(9.2)
1.40(36)
2.00(51)
1/4-20 NCMOUNTING
HOLES
2.63(67)
SENSORCOLLAR
.86(22)
A12/S12
1/2"-13 UNC(10 PL)
Racine Flow Meter Group
RAC
INE FEDERATED IN
C.
ISO 9001 : 2008 FILE N0. A68
56
Introduction
Ordering Information
B1750
Accuracy: ±0.5% over the published flow range with fluids >100 cP; over a 10:1 turndown (from maximum flow) with fluids <30 cP Repeatability: ±0.1%Pressure Rating: 5000 psi [345 bar] maximumOperating Temperature: -20 °F to +185 °F [-29 °C to +85 °C] aluminum -20 °F to +400 °F [-29 °C to +204 °C] stainless steelConnections: Female NPT: ¼", ¾", or 1- ¼" (depending on meter size) Materials of Construction: Stainless steel (gears and bearings) O-Ring: Teflon®, Viton® (optional)Housing: 6061 - T6 aluminum or 303 stainless steel
Specifications
2 3
Operating Principle
K-factor
The Blancett Model B1750 positive displacement flow meter provides high measurement accuracy, trouble-free operation and long service life for fluids over a wide viscosity range. Applications include lubricants, fuels, chemicals and solvents, oils and greases. The B1750 meter is bi-directional (using appropriate electronics) and has an extremely large turndown ratio - up to 400:1 in some models - with full accuracy at extremely low flow rates.
Fluid entering the meter drives two gears. A non-intrusive sensor detects the movement of the gears and produces a sine wave pulse for each gear tooth that passes the path of the sensor face. The resulting pulse frequency is proportional to the actual flow rate, and it provides a highly accurate representation of the fluid flow. The meter is relatively insensitive to changes in viscosity and there is no need for straight run piping.
The K-factor represents the number of output pulses transmitted per unit volume of liquid passing through the positive displace-ment meter. Each meter has a unique K-factor that is determined during factory calibration. The K-factor is very constant and linear over the published flow range when liquid viscosity is greater than 100 cP. When liquid viscosity is less than 100 cP positive displacement meters can experience “fluid slip” in the measuring chamber due to migration of liquid around the internal moving parts. As a result, the linear (constant K-factor portion) measuring range of the flow meter is reduced. At viscosities less than 30 cP, positive displacement meters maintain published linearity over a 10:1 turndown range from the maximum published flow rate.
B1750
Flow Rate vs. Pressure Drop
FLUID FLOW
(IN) (OUT)
Model B1750 Positive Displacement Flow Meters
B175-A12B175-A20B175-A30B175-A60B175-A804
B175-A904
B175-A12-VB175-A20-VB175-A30-VB175-A60-VB175-A80-V4
B175-A90-V4
¼" Female NPT¼" Female NPT½" Female NPT¾" Female NPT
1-¼" Female NPT1-¼" Female NPT¼" Female NPT¼" Female NPT½" Female NPT¾" Female NPT
1-¼" Female NPT1-¼" Female NPT
0.003-0.800.01-2.000.03-7.000.05-20.00.5-60.01-120
0.003- 0.800.01-2.000.03-7.000.05-20.00.5-60.01-120
0.011-3.030.04-7.60.11-26.50.19-75.71.9-2273.8-454
0.011-3.030.04-7.60.11-26.50.19-75.71.9-2273.8-454
53,00015,9006,6001,800
1,600~800~
53,00015,9006,6001,800
1,600~800~
PartNumber1
SealMaterial
EndConnection
Flow Ranges3
Aluminum Housing - 185 °F Maximum Fluid TemperatureK-factor2
Pulses/GalGPM LPM
Teflon®
Standard
Viton®
B175-S12B175-S20B175-S30B175-S60B175-S804
B175-S904
B175-S12-VB175-S20-VB175-S30-VB175-S60-VB175-S80-V4
B175-S90-V4
¼" Female NPT¼" Female NPT½" Female NPT¾" Female NPT
1-¼" Female NPT1-¼" Female NPT¼" Female NPT¼" Female NPT½" Female NPT¾" Female NPT
1-¼" Female NPT1-¼" Female NPT
0.003-0.800.01-2.000.03-7.000.05-20.00.5-60.01-120
0.003- 0.800.01-2.000.03-7.000.05-20.00.5-60.01-120
0.011-3.030.04-7.60.11-26.50.19-75.71.9-2273.8-454
0.011-3.030.04-7.60.11-26.50.19-75.71.9-2273.8-454
53,00015,9006,6001,800
1,600~800~
53,00015,9006,6001,800
1,600~800~
PartNumber1
SealMaterial
EndConnection
Flow Ranges3
303 Stainless Steel Housing - 400 °F Maximum Fluid TemperatureK-factor2
Pulses/GalGPM LPM
Teflon®
Standard
Viton®
¹ Does NOT include pickup - To order, see Optional Magnetic Pick-up, page 4² All K-factors are approximate ³ Accuracy: ±0.5% over the published flow range with fluids >100 cP; over a 10:1 turndown (from maximum flow) with fluids <30 cP 4 90° Flange fittings required for installation, see page 24 of the Blancett Price List~ Configured for Quad-4 sensor output (B170180)
0.005 0.02 0.13 0.26 0.39 0.52 0.66 0.79
80
70
60
50
40
30
20
10
0
105 cSt
80 cSt
63 cSt
30 cSt
15 cSt5 cSt
217.5
203.0
188.5
174.0
159.5
145.0
130.5
116.0
101.5
87.0
72.5
58.0
43.5
29.0
14.5
00.185
0 0.3700.555
0.7400.925
1.1101.294
1.4791.664
1.850
ΔPSI
ΔPSI
ΔPSI
3000 cSt 2000 cSt 1500 cSt
1000 cSt
800 cSt
500 cSt
400 cSt
300 cSt
200 cSt
100 cSt
30 cSt
GPM
GPM
GPM
B1750 - 20 Series Pressure Drop Chart
217.5
203.0
188.5
174.0
159.5
145.0
130.5
116.0
101.5
87.0
72.5
58.0
43.5
29.0
14.5
01.48
0 2.964.44
5.927.4 8.88
10.3611.83
13.3114.79
16.2717.75
ΔPSI3000 cSt 2000 cSt 1000 cSt
500 cSt
300 cSt
100 cSt
50 cSt
30 cSt
GPM
B1750 - 60 Series Pressure Drop Chart
217.5
203.0
188.5
174.0
159.5
145.0
130.5
116.0
101.5
87.0
72.5
58.0
43.5
29.0
14.5
00.53
0 1.061.58
2.112.64
3.173.7 4.23
4.755.28
5.816.34
ΔPSI3000 cSt 2000 cSt 1000 cSt
500 cSt
300 cSt
100 cSt
50 cSt
30 cSt
GPM
B1750 - 30 Series Pressure Drop Chart
120
100
80
60
40
20
0
6.6 13.2
19.8
26.4 33 39.6 45
B1750 - 80 Series Pressure Drop Chart
1000 cSt
300 cSt
150 cSt
40 cSt
217.5
203.0
188.5
174.0
159.5
145.0
130.5
116.0
101.5
87.0
72.5
58.0
43.5
29.0
14.5
013.2
0 26.439.6
52.866 79.2
92.4105.6
118.8132
∆PSI
1000 cSt
300 cSt
10 cSt
30 cSt
GPM
B1750 - 90 Series Pressure Drop Chart
B1750 - 12 Series Pressure Drop Chart
Introduction
Ordering Information
B1750
Accuracy: ±0.5% over the published flow range with fluids >100 cP; over a 10:1 turndown (from maximum flow) with fluids <30 cP Repeatability: ±0.1%Pressure Rating: 5000 psi [345 bar] maximumOperating Temperature: -20 °F to +185 °F [-29 °C to +85 °C] aluminum -20 °F to +400 °F [-29 °C to +204 °C] stainless steelConnections: Female NPT: ¼", ¾", or 1- ¼" (depending on meter size) Materials of Construction: Stainless steel (gears and bearings) O-Ring: Teflon®, Viton® (optional)Housing: 6061 - T6 aluminum or 303 stainless steel
Specifications
2 3
Operating Principle
K-factor
The Blancett Model B1750 positive displacement flow meter provides high measurement accuracy, trouble-free operation and long service life for fluids over a wide viscosity range. Applications include lubricants, fuels, chemicals and solvents, oils and greases. The B1750 meter is bi-directional (using appropriate electronics) and has an extremely large turndown ratio - up to 400:1 in some models - with full accuracy at extremely low flow rates.
Fluid entering the meter drives two gears. A non-intrusive sensor detects the movement of the gears and produces a sine wave pulse for each gear tooth that passes the path of the sensor face. The resulting pulse frequency is proportional to the actual flow rate, and it provides a highly accurate representation of the fluid flow. The meter is relatively insensitive to changes in viscosity and there is no need for straight run piping.
The K-factor represents the number of output pulses transmitted per unit volume of liquid passing through the positive displace-ment meter. Each meter has a unique K-factor that is determined during factory calibration. The K-factor is very constant and linear over the published flow range when liquid viscosity is greater than 100 cP. When liquid viscosity is less than 100 cP positive displacement meters can experience “fluid slip” in the measuring chamber due to migration of liquid around the internal moving parts. As a result, the linear (constant K-factor portion) measuring range of the flow meter is reduced. At viscosities less than 30 cP, positive displacement meters maintain published linearity over a 10:1 turndown range from the maximum published flow rate.
B1750
Flow Rate vs. Pressure Drop
FLUID FLOW
(IN) (OUT)
Model B1750 Positive Displacement Flow Meters
B175-A12B175-A20B175-A30B175-A60B175-A804
B175-A904
B175-A12-VB175-A20-VB175-A30-VB175-A60-VB175-A80-V4
B175-A90-V4
¼" Female NPT¼" Female NPT½" Female NPT¾" Female NPT
1-¼" Female NPT1-¼" Female NPT¼" Female NPT¼" Female NPT½" Female NPT¾" Female NPT
1-¼" Female NPT1-¼" Female NPT
0.003-0.800.01-2.000.03-7.000.05-20.00.5-60.01-120
0.003- 0.800.01-2.000.03-7.000.05-20.00.5-60.01-120
0.011-3.030.04-7.60.11-26.50.19-75.71.9-2273.8-454
0.011-3.030.04-7.60.11-26.50.19-75.71.9-2273.8-454
53,00015,9006,6001,800
1,600~800~
53,00015,9006,6001,800
1,600~800~
PartNumber1
SealMaterial
EndConnection
Flow Ranges3
Aluminum Housing - 185 °F Maximum Fluid TemperatureK-factor2
Pulses/GalGPM LPM
Teflon®
Standard
Viton®
B175-S12B175-S20B175-S30B175-S60B175-S804
B175-S904
B175-S12-VB175-S20-VB175-S30-VB175-S60-VB175-S80-V4
B175-S90-V4
¼" Female NPT¼" Female NPT½" Female NPT¾" Female NPT
1-¼" Female NPT1-¼" Female NPT¼" Female NPT¼" Female NPT½" Female NPT¾" Female NPT
1-¼" Female NPT1-¼" Female NPT
0.003-0.800.01-2.000.03-7.000.05-20.00.5-60.01-120
0.003- 0.800.01-2.000.03-7.000.05-20.00.5-60.01-120
0.011-3.030.04-7.60.11-26.50.19-75.71.9-2273.8-454
0.011-3.030.04-7.60.11-26.50.19-75.71.9-2273.8-454
53,00015,9006,6001,800
1,600~800~
53,00015,9006,6001,800
1,600~800~
PartNumber1
SealMaterial
EndConnection
Flow Ranges3
303 Stainless Steel Housing - 400 °F Maximum Fluid TemperatureK-factor2
Pulses/GalGPM LPM
Teflon®
Standard
Viton®
¹ Does NOT include pickup - To order, see Optional Magnetic Pick-up, page 4² All K-factors are approximate ³ Accuracy: ±0.5% over the published flow range with fluids >100 cP; over a 10:1 turndown (from maximum flow) with fluids <30 cP 4 90° Flange fittings required for installation, see page 24 of the Blancett Price List~ Configured for Quad-4 sensor output (B170180)
0.005 0.02 0.13 0.26 0.39 0.52 0.66 0.79
80
70
60
50
40
30
20
10
0
105 cSt
80 cSt
63 cSt
30 cSt
15 cSt5 cSt
217.5
203.0
188.5
174.0
159.5
145.0
130.5
116.0
101.5
87.0
72.5
58.0
43.5
29.0
14.5
00.185
0 0.3700.555
0.7400.925
1.1101.294
1.4791.664
1.850
ΔPSI
ΔPSI
ΔPSI
3000 cSt 2000 cSt 1500 cSt
1000 cSt
800 cSt
500 cSt
400 cSt
300 cSt
200 cSt
100 cSt
30 cSt
GPM
GPM
GPM
B1750 - 20 Series Pressure Drop Chart
217.5
203.0
188.5
174.0
159.5
145.0
130.5
116.0
101.5
87.0
72.5
58.0
43.5
29.0
14.5
01.48
0 2.964.44
5.927.4 8.88
10.3611.83
13.3114.79
16.2717.75
ΔPSI3000 cSt 2000 cSt 1000 cSt
500 cSt
300 cSt
100 cSt
50 cSt
30 cSt
GPM
B1750 - 60 Series Pressure Drop Chart
217.5
203.0
188.5
174.0
159.5
145.0
130.5
116.0
101.5
87.0
72.5
58.0
43.5
29.0
14.5
00.53
0 1.061.58
2.112.64
3.173.7 4.23
4.755.28
5.816.34
ΔPSI3000 cSt 2000 cSt 1000 cSt
500 cSt
300 cSt
100 cSt
50 cSt
30 cSt
GPM
B1750 - 30 Series Pressure Drop Chart
120
100
80
60
40
20
0
6.6 13.2
19.8
26.4 33 39.6 45
B1750 - 80 Series Pressure Drop Chart
1000 cSt
300 cSt
150 cSt
40 cSt
217.5
203.0
188.5
174.0
159.5
145.0
130.5
116.0
101.5
87.0
72.5
58.0
43.5
29.0
14.5
013.2
0 26.439.6
52.866 79.2
92.4105.6
118.8132
∆PSI
1000 cSt
300 cSt
10 cSt
30 cSt
GPM
B1750 - 90 Series Pressure Drop Chart
B1750 - 12 Series Pressure Drop Chart
Model 200
Blancett is a registered trademark of Racine Federated Inc. Teflon and Viton are registered trademarks of E.I. duPont de Nemours and Company
Flow Meters®
Flow Meters®
Division of Racine Federated Inc.800-235-1638 www.blancett.com
Positive Displacement Flow MetersB1750
B1750 Positive Displacement Flow Meter
Accuracy of ±0.5% of reading and repeatability of ±0.1%
No need for additional straight run piping
Designed for fluids with a wide range of viscosities, as well as low flow rates
Available in high strength aluminum or stainless steel housing
© 2009 Blancett Printed in USA 10/09 Form No. 1750
B1750 Dimensions - Inches (mm)
A20/S20 A60/S60 A80/S80
3.3(84.4)DIA
.47(12)
2.17(55)
1.73(44)
.40(10.2)
.40(10.2)
4.9(125)DIA
.91(23)
3.78(96)
1.61(41)
2.36(60)
1.25(32)2.63
(67)5.50(140)
.63(16)
7.85(199)DIA
5.50(140)
This variable reluctance magnetic pickup coil (B170109) is designed to exceed the performance and application criteria of any standard or modified pickups. Its modular design allows it to be used with the B1750 positive displacement meter, and interface with all Blancett electronics. If using another manufacturer’s electronics with this meter, a Blancett B170210 pre-amplifier may be needed to correctly interface the devices.Output: 30 mV – 3 VAC Sine Wave (B170109) 0-10 V – Square Wave (B170210) 4-20 mA - 3 wire 4-20 mA output (B175420)Connector: 2-pin gold plated type to mate with MS3106-10SL-4S or equivalent (B170109) 3-pin gold plated type to mate with MS3106A-10SL-3S or equivalent (B170210) Temperature: -100 °F to +325 °F (-73 °C to +162 °C) (B170109) -20 °F to +160 °F (-29 °C to +71 °C) (B170210) 0 °F to +185 °F (-18 °C to + 85 °C) (B175420)Materials of Construction: 303/304 stainless steel shell and bottom, solid epoxy encapsulation, standard commercial finish
Note: 80/90 Series utilize Quad-4 Sensor (B170180)
Optional Magnetic PickupUsed with 12, 20, 30 and 60 series only
.51(13)
2.64(67)
3.17(80.4)DIA
4.72(120)DIA
3.15(80)DIA
1.73(44)
3.32(84.4)DIA
A30/S30
1/2"-13 UNC(10 PL)
2.63(67)5.50(140)
1.25(32)
1.61(41)
A90/S90
7.00(178)
7.85(199)DIA
2.00(51)
1.50(38)
SENSOR HOLE(1/2-20 NF)
1/4 NPTPORTS
1.00(26)
.36(9.2)
1.40(36)
2.00(51)
1/4-20 NCMOUNTING
HOLES
2.63(67)
SENSORCOLLAR
.86(22)
A12/S12
1/2"-13 UNC(10 PL)
Racine Flow Meter Group
RAC
INE FEDERATED IN
C.
ISO 9001 : 2008 FILE N0. A68
56