®

Environmentally Sensible & Commercially Proven Solutions to Fluid Treatment Through Applied Magnetohydrodynamics

Fluid Dynamic Power Cells

results speak for themselves...

A major international

chemical and synthetic fiber

manufacturer solved their

scale problems with

ENEFLOW Fluid Dynamic

Power Cells. The

installations have been

carefully documented and

monitored by plant

engineers to determine the

effectiveness of the

ENEFLOW systems.

Mineral scale build-up was

effectively eliminated from

all fluid flow components in

only ten short months,

providing for more energy

efficient operation.

ENEFLOW 5000's installed on the plant's cooling water system for its diesel power generators effectively eliminated scale problems in their pumps, before (lett) and after (right).

Valves in the cooling water lines covered with hard scale (left) until ENEFLOW Power Cells eliminated it completely (right).

Engineers at a coal fired

power station had an on-

going problem with rock-hard

calcium carbonate scale

build-up in their ash slurry

piping system. They wanted

to see if the ENEFLOW

Power Cells would eliminate

existing scale and control

future scale build-up. The

maintenance engineers were

amazed with the results...

Hard calcium carbonate scale

build-up is an on-going

maintenance problem,

especially on valves as seen

here.

Four pair of ENEFLOW Fluid Dynamic Power cells being installed on one of the main (14 inch) ash slurry lines.

One month after ENEFLOW Power cells were installed on the line, the hard white scale had turned yellowish and softened considerably.

After two months, ENEFLOW Power cells had virtually eliminated the calcium carbonate scale build-upin the system.

These critical heat exchangers at a tire manufacturing

plant were scaling up badly and had to be cleaned every

few months. The results after just thirty days were

"miraculous" according to the plant engineers! The photos

speak for themselves.

BEFORE AFTER

BEFORE AFTER

BEFORE AFTER

BEFORE AFTER

®

Chemical Company... Power Plant...

Tire Company...

Fluid DynamicPower Cells

No Chemicals

Environmentally safe

Control mineral scalebuild-up

Improve andaccelerate reagentdiffusion such ascorrosion inhibitors,disinfectants, etc.

Maintenance free

®

Magnetohydrodynamics (MHD)

Our patented ENEFLOW

Fluid Dynamic Power Cells

can eliminate and control

scale build-up in all types of

fluid flow systems caused by

dissolved diamagnetic

earthsalts in hard water -

minimizing and sometimes

eliminating the need for

chemicals or complicated

equipment to maintain. The

most common of these

minerals, of course, are

calcium and magnesium.

Furthermore, when

ENEFLOW Fluid Dynamic

Power Cells are installed in a

fluid flow system, they can

improve the bactericidal

circuits incorporate

multi-pole, multi-axial,

permanent magnetic flux

generators which uniquely

concentrate the magnetic

forces for maximum

descaling effect.

ENEFLOW’s

Fluid Dynamic Power Cells

are the only permanent

magnetic circuits available

that utilize a blend of nickel,

cobalt, aluminum and

neodymium iron boron

chemically bonded to

magneto-ceramic ferrite.

The resultant magnetic flux

generators exhibit

extraordinary fluid

treatment characteristics.

function of disinfectants,

accelerate reagent diffusion

and improve the efficiency of

ion-exchange resins.

ENEFLOW ’s

revolutionary magnetic

Although the most common

fluid is water, ENEFLOW

systems will condition many

different types of fluids

including crude oil, gasoline,

diesel & heating fuels, low

pressure steam, saltwater,

waste water, green & black

liquor in pulp & paper mills,

etc.

The list of applications is

limited only by the fluid's

chemistry, velocity,

temperature and your own

engineering imagination.

ENEFLOW Fluid Dynamic

Power Cells are non-invasive

and are installed around a

pipe. There is no need to cut

into a line to plumb-in a

system. No external energy

source is required and

ENEFLOW Power Cells are

completely maintenance free.

Furthermore, they are 100%

environmentally safe.

Magnetohydrodynamics

(MHD) is a relatively

young scientific

discipline. Simply

put, it refers to the

principles of motion of

a fluid affected by a

magnetic field. Developed

mainly during the last three

decades or so, it has scarcely

reached maturity.

Yet, in recent years magnetics

have been at the cutting edge

of dramatic new technologies

applied to medicine, nuclear

engineering, thermodynamics,

propulsion and transportation.

Examples include MRI,

magnetic resonance imaging,

which has revolutionized

diagnostic medicine. Other

practical applications of

magnetohydrodynamics

include moving ships without

propellers and trains without

wheels!

Building on these extraordinary

developments, our researchers

and engineers have now taken

fluid flow systems performance

enhancement technology into

the 21st century through

applied MHD for controlling

mineral scale build-up and

scale-induced corrosion.

AFTER

BEFORE

®

When hard water is subjected

to fluid dynamic changes

(pressure, velocity, tern

perature), dissolved minerals

precipitate out of solution and

migrate to the area of lowest

fluid velocity typically, the walls

(interior surfaces) of pipes and

equipment restricting the fluid

flow. This scale also acts as an

insulator, dramatically reducing

heat transfer efficiency.

However, when a conductive

fluid passes through a

magnetic field, an

electromotive force is induced

through the fluid perpendicular

to the direction of fluid flow and

the flux field. This electrical

discharge through the fluid

induces a positive polarity in

the fluid. The magnetic flux

field further causes polar water

molecules to be aligned along

the flux or magnetomotive

force vector, thus affecting the

kinetics of crystallization of the

minerals in the water. Random

covalent bonding of the

nucleation points of these scale

forming molecular clusters is

reduced and, therefore, these

minerals stay in suspension.

They are prevented from

"Magnetic waterconditioners,a non-chemicalmethod for treatingwater, are operatingextensively through-out the world todaywith tremendouseconomic effect."

Report prepared byTulane University for the U.S. Dept of EnergyUnder ContractNo. FG01-82CE40568

growing so large so as to

precipitate out of solution and

form hard scale on the walls

of pipes and equipment. This

process is called "magnetic

homogenization."

Interestingly, in fuel

applications, the ENEFLOW

Power Cells affect the

suspended carbon and other

diamagnetic impurities in the

fuel. They prevent large

macromolecules of these

impurities from forming,

thereby enhancing complete

combustion. ENEFLOW

Power Cells have been

shown to improve fuel

efficiency and reduce harmful

emissions on many different

types of vehicles. They can

also help reduce carbon

build-up in engines.

But products alone are not

enough. The experience,

dedication, professionalism

and know-how of the people

behind the products are

equally important to insure

success. The ENEFLOW

Engineering Team has

dozens of years of combined

practical experience not only

in low energy applied fields

but, as importantly

erosion/corrosion control in all

types of fluid flow systems, in

all types of industries.

Ideally, all incoming water

should be treated with

ENEFLOW Fluid Dynamic

Power Cell systems.

Water/fluids should be

treated just prior to point of

use, i.e., ahead of chillers,

humidifiers, boilers, cooling

towers, heat exchangers, etc.

In re-circulating systems,

both the make-up and re-

circulating water should be

treated.

Power

Cells accelerated

chlorine diffusion in

hard water so

effectively that 65%

less chlorine was

required to control

macro-fouling and

bio-film build-up in

service water

systems...

...Sediment build-upwas also controlled,heat transfer rateswere maintained atoptimum efficiencyand pH levels weredramaticallystabilized.

"Alternatives to Chlorination"Sponsored by a Major U.S.Nuclear Power Company

How does the patented system work?

General Guidelines

®

ENEFLOW systems don't technically 'soften’ hard water.

‘Softening’ usually means replacing some of the most

essential minerals in the water with SODIUM, which doctors

warn endangers health; or removing those minerals with

special filters. Both methods present problems because of

their pollution, health risks and/or wasted water. ENEFLOW

systems treat water without chemicals through the principles

of physics.

Furthermore, ENEFLOW systems accelerate reagent

diffusion, making chemicals such as disinfectants, biocides,

corrosion inhibitors, etc., more efficient and effective.

The high cost of 'scale' (typical energy losses)The table shows typical loss of efficiency proportionalto varying thicknesses of scale.

This table clearly illustrates the importance of maintaining your HVAC equipment. You could be wasting a hugepercentage of your energy production due to scale build-up in boilers, water heaters and heat exchangers.

scale thickness efficiency loss coal wasted per ton oil wasted per 1000 gal gas wasted per 1000 cu ft

1/64 in.

1/32 in.

1/16 in.

1/8 in.

3/16 in.

1/4 in.

3/8 in.

1/2 in.

5/8 in.

3/4 in.

4%

7%

11%

18%

27%

38%

48%

60%

74%

90%

80 lb.

140 lb.

220 lb.

360 lb.

540 lb.

760 lb.

960 lb.

1200 lb.

1480 lb.

1800 lb.

40 gal.

70 gal.

110 gal.

180 gal.

270 gal.

380 gal.

480 gal.

600 gal.

740 gal.

900 gal.

40 cu. ft.

70 cu. ft.

110 cu. ft.

180 cu. ft.

270 cu. ft.

380 cu. ft.

480 cu. ft.

600 cu. ft.

740 cu. ft.

900 cu. ft.

The benefits of :

The Magnetic Circuitis divided into two parts:

(1) The permanent magnetic flux generators

which supply the magnetomotive or driving

force.

(2) The particular path the flux takes in getting

from one pole of the flux generator to the

other.

Our researchers have developed a unique

magnetic circuit power cell design which

directs the useful flux into the fluid and

minimizes flux ‘leakage’. The powerful and

unique magnetic circuit produces an optimum

residual induction in excess of 12,000 gauss -

making the ENEFLOW Fluid Dynamic Power

Cell the most powerful permanent magnetic

circuit available for magnetohydrodynamic

treatment of fluids.

®

®

Production on a small well such as the one pictured is approximately +/- 85 barrels per day. A loss of 5 barrels per day is attributed to paraffin build-up.

But, lost production is only a small portion of the cost associated with paraffin build-up. You also have to take into account the cost of ‘hot oiling’ or ‘stripping’ a well to remove the paraffin build-up. The average cost for cleaning a well of this size is approximately $400 per cleaning and this has to be done on an average of once or twice a month.

The ENEFLOW Power Cells were installed on the two inch line coming off the well head for approximately 60 days and the end result was that the ENEFLOW units removed the existing paraffin and prevented any additional build-up.

Power Cells Eliminate Paraffin Build-Up for Oil & Gas Company

®

Unit fits copper, plastic, galvanized iron, steel and stainless steel pipes with sizes ranging from 2 in. to 24 in., O.D. Units are typically ‘ringed’ around the pipe using the following formula as a guide:

One (1) pair for every (2) inches of pipe diameter.

(For example: 8” pipe = 4 pair)

For very turbulent fluid flow situations or on large pipes (greater than 12 in. O.D.), a multi-stage installation may be necessary for optimum performance.

Can be used wherever mineral scale build-up and scale induced corrosion present problems in your fluid flow system.

Power Cell SystemHeavy Duty Industrial/InstitutionalBasic Residential/Commercial

Power Cell System

Unit fits copper, plastic, galvanized iron, steel and stainless steel pipes up to 1.5 in., O.D., (up to 2.0 in. on P.V.C pipes). General purpose unit recommended for most applications in the home, office complex, restaurant, swimming pools, etc.

Can be used on water and heating fuel lines! Eliminates scale and scale induced corrosion in water systems, as well as improves combustion efficiency in oil burners/boilers.

For general use, install one system on incoming cold water line at least two (2) feet after the water meter or pressure tank (if well water), and a second system on the hot water line at least two (2) feet after the hot water heater or boiler for best results.

®

5000®

0001

Eliminate scale & scale

induced corrosion and

help stabilize pH in all

types of fluid flow systems

without chemicals:

• Piping systems

• Cooling towers

• Heat exchangers

• Boilers

• Oil/fuel lines

• Water wells

• HVAC systems

• Water heaters

• Irrigation systems

• Swimming pools/spas

• Car washes

• Laundries

Thousands of applications in all

types of industries and institutions:

• Power plants/nuclear & fossil

• Petrochemical plants

• Pulp & paper mills

• Marine

• Waste water treatment facilities

• Parks departments

• Schools

• Hospitals

• Correctional facilities

• Pharmaceutical plants

• Food processing plants

• Hotels/motels

• Amusement/theme parks

• Oil drilling/pipelines

• Transportation

• Mining/quarrying

• Stores/shopping centers

• Restaurants

• Residences

Fluid Dynamic Power Cells...

® Your local ENEFLOW Fluid Flow Systems Specialist

ENEFLUX ARMTEK MAGNETICS, INC.6 Pheasant Run

Newtown, PA 18940-1819215-504-1000215-504-1001

Ph: Fx:

www.eamagnetics.com

BEFORE

AFTER

E.A.M. is an ENECON Company. www.enecon.com

®

ENEFLOW’s multi-pole, multi-axial, magnetic flux generators

are permanent installations, require no maintenance and are

environmentally safe!

ENEFLOW Power Cells are GUARANTEED not to lose power

for ten years!

®

Condition water with no

salt, no chemicals and

no external energy

consumption!