Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
FOAMGLAS®
S3 CELLULAR GLASS
RIGID FOAM INSULATION
Physical Properties
Features
PROPERTY TEST METHOD VALUE
PHYSICAL
Composition Inorganic. Soda lime glass.
Density, minimum pcf (kg/m3) ASTM C303 6.9 (110)
Closed Cell Content, minimum % Helium Pycnometer 98
Service Temperature, ºF (ºC) -445 to 806 (-265 to 430) no load
MOISTURE
Capillarity None
Hygroscopicity No increase in weight at 90% relative humidity
Water Absorption, maximum vol % ASTM C240 0.1%
Water Vapor Permeability, maximum perm-in (ng/Pa-s-m) ASTM E96 0.005 (.007)
Mold/Mildew Resistance ASTM C1338 Pass
Corrosion Resistance ASTM C1617 Pass (steel, less than DI water)
Hydrostatic Resistance, minimum equivalent water height in feet (meters) ASTM D5385/C1306 34.5 (10.5)
DIMENSIONAL
Coefficient of Linear Thermal Expansion, maximum in/in/ºF (mm/mm/ºC) ASTM E228 5.0 x 10-6 (9.0 x 10-6)
Dimensional Stability1, %, maximum@ 158°F / 97% R.H.@ -40°F / ambient R.H.@ 200°F / ambient R.H.
ASTM D2126 1.01.01.0
MECHANICAL
Compressive Strength (capped), minimum psi (kPa) ASTM C165 Procedure A/ASTM C240 130 (900)
Flexural Strength, psi (kPa), minimum ASTM C203 72.5 (500)
Modulus of Elasticity, ksi (MPa), Approximate (ν = 0.25)PerpendicularParallel
ASTM C623 168 (1158)199 (1372)
FIRE
Combustibility ASTM E136 Non-combustible
Surface Burning Characteristics, maximumFlame Spread IndexSmoke Developed Index
ASTM E84 Unfaced 0, Faced NR1
Unfaced 0, Faced NR1
THERMAL Thermal Resistance per inch @ 75ºF (24ºC) mean temperature2, Hr-ft2-ºF/BTU (m2-ºC/W) ASTM C518/ASTM C177 3.0 (0.54)
1. Maximum change in any dimension.2. R means the resistance to heat flow; the higher the value, the greater the insulation power. This insulation must be installed properly to get the market R-value. Follow the manufacturer’s instructions carefully.3. Facing not rated for flame propagation resistance (for use in non-exposed applications only). Refer to the fire rating for the desired assembly (see the applicable FM or UL certifications).
• Excellent dimensional stability• Water proof• Vapor impermeable• Non-combustible• High compressive strength• Rot & insect resistant• Inorganic
Owens Corning® FOAMGLAS® S3 cellular glass insulation is a closed cell, high performance, rigid foam board specifically designed for building and roofing applications. It provides a unique combination of properties that offer an alternative to other types of building insulation. For use where high loads and equipment vibration are present.
Roof Applications
Availability
Facings
Disclaimer of LiabilityPittsburgh Corning, LLC shall not be liable for incidental and consequential damages, directly or indirectly sustained, nor for any loss caused by application of these goods not in accordance with current printed instructions or for other than the intended use. Pittsburgh Corning, LLC liability is expressly limited to replacement of defective goods. Any claim shall be deemed waived unless made in writing within (30) days from date it was or reasonably should have been discovered.
Certifications and Sustainable Features
Environmental and Sustainability
• Certified by natureplus institute SCE to contain a minimum of 60% recycled glass (external production waste, building site waste, post-consumer waste) – certificate 0406-1101-101-1.
• Environmental Product Declaration (EPD) has been certified by IBU (Institut Bauen und Umwelt e.V.) – certificate EPD-PCE-20150040-IBA1-EN
• Unfaced product meets the requirements of CA CDPH SM V1.2 for VOC emissions and formaldehyde; French VOC Emissions Class A+
Owens Corning is a worldwide leader in building material systems, insulation and composite solutions, delivering a broad range of high quality products and services.
Owens Corning is committed to driving sustainability by delivering solutions, transforming markets and enhancing lives. More information can be found at www.owenscorning.com.
Standards, Codes Compliance• UL (Underwriters Laboratories) Roof Deck Constructions, tested in
accordance with UL 1256• FM (Factory Mutual) Class 1 Roof Decks• ASTM E108 Fire Classified Assemblies • ASTM E119 Fire Resistance Rated Roof Assemblies • UL and FM Wind Uplift Rated Assemblies • Compliance verification by R.J. Lee Group
THICKNESS4 WIDTHS LENGTHS
Block 1.58" (40mm) – 7.87" (200mm) 17.71" (450mm) 23.62" (600 mm)
Board 1.9" (50mm) – 7.87" (200mm) 23.62" (600mm) 47.24" (1200mm)
4. Thicknesses are available in 0.39” (10mm) increments.5. Tapered products are available in 1/8” and 1/4” slope.
PRODUCT FLAT PLAZA VEGETATIVE SOLAR METAL TRAFFIC HEAVY TRAFFIC
T3+ • • • •T4+ • • • • •S3 • • • • • •F • • • • • • •
TOP SURFACE BOTTOM SURFACE
PRODUCT UNFACED
BITUMEN COATED WITH A SACRIFICIAL POLYETHYLENE PROTECTIVE SHEET DESIGNED FOR TORCH-ON MEMBRANES APPLIED TO UPPER SURFACE.
BITUMEN ADHERED FIBERGLASS FLEECE FACER DESIGNED FOR MECHANICAL ATTACHED OR FULLY ADHERED MEMBRANES TO THE UPPER SURFACE.
UNFACED
BITUMEN ADHERED FIBERGLASS FLEECE FACER DESIGNED FOR HOT OR COLD APPLIED ADHESION TO ROOF DECK OR MULTIPLE LAYER SYSTEMS.
Block x x
Ready Block x x
Pub. No. 10024058. Printed in U.S.A. July 2020. © 2020 Owens Corning. All Rights Reserved.
OWENS CORNING INSULATING SYSTEMS, LLCONE OWENS CORNING PARKWAY
TOLEDO, OHIO, USA 436591-800-GET-PINK®
www.owenscorning.com/foamglas
PITTSBURGH CORNING, LLCONE OWENS CORNING PARKWAY
TOLEDO, OHIO, USA 43659www.foamglas.com