FOR AUTOMOTIVE LCD MODULE - TianMa

MODULE No.: TM070RDHGZ1

TIANMA MICROELECTRONICS CO., LTTIANMA MICROELECTRONICS CO., LT Company confidential. Duplication or disclosure prohibited. All rights reserved

SPECIFICATION

FOR AUTOMOTIVE LCD MODULE

□ Preliminary Specification ■ Final Specification

PREPARED CHECKED VERIFIED BY QA

DEPT VERIFIED BY R&D

DEPT

温映辉

Ray Wen

万江

Jon Miller

王勃暐

Davis Wang

卢锦华

Timothy Lu

MODEL NO TM070RDHGZ1

CUSTOMER

VERSION V1.4

CUSTOMER

APPROVED


TIANMA TIANMA MICROELECTRONICS CO., LTMICROELECTRONICS CO., LT 1 / 21 Company confidential. Duplication or disclosure prohibited. All rights reserved

REVISION RECORD

Date Rev.No. Page Revision Items Prepared

2014-12-11 V0.1 - First Release for project kick off purpose. Wang Liu

2015-5-12 V0.2

Page8 Page9

Page10 Page16 Page19 Page24 Page25

1. Modify item 5 Absolute Maximum Ratings. 2. Modify item 6 Electrical characteristics. 3. Modify item 6.3 Backlight Unit characteristics. 4. Modify item 7 Optical Characteristics. 5. Modify item 7 Reliability Test Criteria. 6.Add item 10 Package Method. 7. Add item 11 Appendix.

Wang Liu

2015-5-28 V1.0 All Re-arrangement of pages. Wen

Yinghui

2015-8-14 V1.1

P8 P11

P6,16 P18

P16,17

1. Delete the Power Consumption in 5.3. 2. Delete the Thermistor resistance vs

Temperature curve in 5.5. 3. Change the Mechanical Drawing. 4. Renew the Reliability Test.

Wen Yinghui

2015-8-25 V1.2 P6,16 Change the Storage Tem. from 90℃ to 95℃. Wen

Yinghui

2015-9-21 V1.3 P16 Change Mechanical Shock Test from 2 times to 3 times.

Wen Yinghui

2015-10-16 V1.4 P19 P14

Update the product inspection criteria and Optical Characteristics.

Wen Yinghui



Table of Contents

1 Precautions for Use of LCD Modules ............................................................................................. 1

2 General Specifications ................................................................................................................ 4

3 Circuit BlocK Diagram ................................................................................................................. 5

4 Absolute Maximum Ratings ......................................................................................................... 6

5 Electrical Specifications ............................................................................................................... 7

6 Optical Characteristics .............................................................................................................. 14

7 Reliability Test Items and Criteria .............................................................................................. 16

8 Mechanical Drawing .................................................................................................................. 18

9 Product Inspection Criteria ........................................................................................................ 19

10 Package Method ..................................................................................................................... 21



1. Precautions for Use of LCD Modules 1.1 Handling Precautions 1.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping

it from a high place, etc. 1.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be

sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water.

1.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary.

1.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle the polarizer carefully.

1.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents:

－ Isopropyl alcohol － Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: － Water － Ketone － Aromatic solvents

1.1.6 Do not attempt to disassemble the LCD Module. 1.1.7 If the logic circuit power is off, do not apply the input signals. 1.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an

optimum work environment. 1.1.8.1 Be sure to ground the body when handling the LCD Modules. 1.1.8.2 Tools required for assembly, such as soldering irons, must be properly grounded.

1.1.8.3 To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions.

1.1.8.4 The LCD Module is covered with a film to protect the display surface. Be carefully and slowly when peeling off this protective film since static electricity may be generated.

1.2 Storage precautions 1.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 1.2.2 The LCD modules should be stored under the storage temperature range. the recommend condition is: Temperature : 0℃ ～ 40℃, Relatively humidity: ≤80%, and no more than 1 year. 1.2.3 The LCD modules should be stored in the room without acid, alkali and sulfur compound harmful gas, etc. 1.3 Transportation Precautions 1.3.1 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine.



2. General Specifications TM070RDHGZ1 is an Amorphous-TFT-LCD (Thin Film Transistor Liquid Crystal Display) module. It is composed of a 7.0 inch TFT-LCD panel, LCD Driver IC with T-con integrated, FPC(flexible printed circuit) and a backlight unit, This 7.0 inch TFT-LCD Normally White Robust TN technology module is designed for Automotive applications.

Features Spec

Display Spec.

Size 7.0inch Resolution 800RGB x 480 Technology Type a-Si TFT Pixel Configuration RGB stripe Display Mode TN Normally White Surface Treatment AG Viewing Direction 12 o’clock Gray Scale Inversion Direction 6 o’clock

Mechanical Characteristics

LCM (W x H x D) (mm) with CG 168.38x101.86x6.9 Active Area(mm) 154.08×85.92 Pixel Pitch(mm) 0.1926×0.1790 With /Without TSP NA Connection Type ZIF Connector on customer side LED Numbers 12 Weight (g) 177±5%

Electrical Characteristics

Interface Digital RGB Color Depth 16M (24bit) colors Driver IC Novatek

Note 1: Color tune is slightly changed by temperature and driving voltage.

Note 2: Requirements on Environmental Protection:Q/S0002(ROHS requirements contained)

Note 3: The height dimension does not include protect film.



3. Circuit Block Diagram

Figure3.1 LCM Block Diagram Scan Mode:

Figure3.2 Scan Direction Diagram



4. Absolute Maximum Ratings

(Ta=25℃) Item Symbol MIN MAX Unit Remark

Power Supply Voltage 1 VDD -0.3 5.0 V Note1 Power Supply Voltage 2 AVDD -0.3 15 V Note1 Power Supply Voltage 3 VGH -0.3 40 V Note1 Power Supply Voltage 4 VGL -20 0.3 V Note1 Supply Range VGH-VGL -0.3 40 V Note1 Back Light Forward Current If - 240 mA Note4 Operating Temperature TOPR -30 85 ℃ Note2 Storage Temperature TSTG -40 95 ℃ Note1: The parameter is for driver IC (gate driver, source driver) only. Note2: 85℃ is the surface temperature of module. Note3: Functional operation should be restricted under normal ambient temperature Note4: Each LED Ambient Temperature vs Allowable Forward Current curve as bellow. There are total two LED channels in back light unit Under LCM operating, the stable forward current should be inputted. Each channel recommended maximum current: 120 mA. When under LCM operating, the LED forward current should follow the De-rating curve.



5. Electrical Specifications 5.1 Electrical characteristics(GND=0V,Ta=25℃)

Table 5.1.1 Electrical characteristics VDD=3.3V, DCLK=29.2MHz,AVDD=11.5V,VGH=24V,VGL=-7.5V,Vcom=4.5V,GND=AGND=0V, Ta = 25℃

Item Symbol Min Typ Max Unit Remark

Digital Supply Current IVDD - - 25.00 mA

Analog Supply Current IAVDD - - 45.00 mA

Gate On Current IGH - - 0.60 mA

Gate Off Current IGL - - 0.60 mA Power Consumption

Panel Power Consumption Black Mode (60Hz)

- - 640 mW

Standby mode Standby Mode - - 1 mW

Table 5.1.2 LCD module electrical characteristics 5.2 Gamma Voltage For Reference (Gamma Correction: Typ. 2.2)

Table 5.2 LCD module Gamma Voltage specification

Item Symbol MIN TYP MAX Unit Remark

Power Supply Voltage

VDD 3.0 3.3 3.6 V AVDD 11.2 11.5 11.8 V VGH 23.5 24.0 24.5 V VGL -8.0 -7.5 -7.0 V

VCOM 4.3 4.5 4.7 V

Input Signal Voltage

Low Level VIL 0 - 0.3*VDD V R0~R7,G0~G7,B0~B7,

HS,VS,DCLK,DE,RSTB,HLR,DITHB,

STBYB,UPDN,SHLR,DITHB

High Level VIH 0.7*VDD - VDD V

Output Signal Voltage

Low Level VOL - - GND+0.4 V

High Level VOH VDD-0.4 - - V

Power Consumption

Black Mode (60Hz)

- - 640 mW

Standby Mode - - TBD uW

Back Light - (2.88) 3.31 W Vf=18V, Iled=80mA,

12LEDs

Item Specification Unit Item Specification Unit V1 (11.10)

V

V14 (0.10)

V

V2 (10.72) V13 (0.49) V3 (8.79) V12 (2.36) V4 (8.22) V11 (2.97) V5 (7.78) V10 (3.40) V6 (7.08) V9 (4.11) V7 (6.10) V8 (5.10)



5.3 Backlight Unit Ta=25℃

Table5.3.1 Backlight unit electrical characteristics

Figure 5.3.2 Backlight circuit diagram

Note 1: IBL is defined for one channel LED, There are total two LED channels in backlight unit Under LCM operating, the stable forward current should be inputted. Note 2: IBL =80mA. Note 3: Optical performance should be evaluated at Ta=25℃ only. If LED is driven by high current, high ambient temperature & humidity condition. The life time of LED will be reduced. Operating life means brightness goes down to 50% of original brightness. Note 4: The NTC thermistor is included in LED circuit and the part No. is NCP18XH103F0SRB, It's used for the LED controlling and the location is in the middle of the LED circuit on backlight FPC. Note 5: Recommended derating curve, dimming should operate at Ta≧70℃. Regarding LED

current's derating in backlight, please see the following chart.(The following chart is based on the only LCD module level without customer system,and depending on customer's system condition, the following chart can be changed.)

Figure 5.3.3 Backlight De-rating curve

Item Symbol MIN TYP MAX Unit Remark Forward Current IBL -- 80 mA Note 1,2 Forward Voltage VBL 15.9 18.0 20.7 V Note 1,2 Backlight Power Consumption WBL -- 2.88 3.312 W Note 1,2 Life time -- 10000 -- -- Hrs Note 3,4,5



5.4 Interface Signals 5.4.1 CN1 Pin assignment Mating Connector: FH28-60S-0.5SH (HIROSE).

No Symbol I/O Description Remark 1 GND P Ground 2 VGL P Negative gate power supply voltage 3 GND P Ground 4 VGH P Positive gate power supply voltage 5 VCOM P Common Reference voltage 6 AVDD P Power for analog circuit 7 GND P Ground 8 VDD P Power supply 3.3V(Type)

9 RSTB I Global reset signal. RSTB=”1”, Normal operation. (Default). RSTB=”0”, The controller is in reset state.

10 STBYB I Standby mode control signal. STBYB=H, Normal operation; STBYB=L, Standby mode.

11 MODE I DE/SYNC mode select control signal. MODE=1,DE mode, HS=H,VS=H; MODE=0, HSD/VSD mode. DE=L.

12 R0 I Red data input (LSB)

Note 2

13 R1 I Red data input 14 R2 I Red data input 15 R3 I Red data input 16 R4 I Red data input 17 R5 I Red data input 18 R6 I Red data input 19 R7 I Red data input 20 G0 I Green data input (LSB)

Note 2

21 G1 I Green data input 22 G2 I Green data input 23 G3 I Green data input 24 G4 I Green data input 25 G5 I Green data input 26 G6 I Green data input 27 G7 I Green data input 28 B0 I Blue data input (LSB)

Note 2

29 B1 I Blue data input 30 B2 I Blue data input 31 B3 I Blue data input 32 B4 I Blue data input 33 B5 I Blue data input 34 B6 I Blue data input 35 B7 I Blue data input 36 GND P Ground 37 V1 P Gamma correction reference Voltage 38 V2 P Gamma correction reference Voltage 39 V3 P Gamma correction reference Voltage 40 V4 P Gamma correction reference Voltage 41 V5 P Gamma correction reference Voltage 42 V6 P Gamma correction reference Voltage 43 V7 P Gamma correction reference Voltage



44 V8 P Gamma correction reference Voltage

45 V9 P Gamma correction reference Voltage

46 V10 P Gamma correction reference Voltage 47 V11 P Gamma correction reference Voltage 48 V12 P Gamma correction reference Voltage 49 V13 P Gamma correction reference Voltage 50 V14 P Gamma correction reference Voltage 51 GND P Ground

52 DCLK I Clock signal For input data.Data latched at falling edge.

53 GND P Ground

54 DE I Data input Enable signal.Active High to enable the data input bus under “DE Mode”.

55 HS I Horizontal sync input signal.Negative polarity. 56 VS I Vertical sync input signal.Negative polarity.

57 UPDN I Up/Down scan Direction selection; UPDN=0,From up to down; UPDN=1, From down to up.

58 SHLR I Left / Right scan Direction selection SHLR=1, From left to right; SHLR=0, From right to left.

59 DITHB I Dithering function enable control signal. DITHB=H, Disable internal dithering function; DITHB=L, Enable internal dithering function. Note 2

60 GND P Ground

Table 5.4.1 Pin assignment (Panel Interface) Note 1: I/O------ definition I-----Input, O------Output, P------Power Note 2: DITHB=H,R[0,1]=”00”,G[0,1]=”00”,B[0,1]=”00”; Note 3: All of GND pins should be connected to system ground. 5.4.2 CN2 Pin assignment Mating Connector: FH28-10S-0.5SH (HIROSE).

Table 5.4.2 Pin assignment (Backlight Interface)

No. symbol Description Remark 1 NC Keep this pin open 2 A1 LED Anode 3 C1 LED Cathode 4 NC Keep this pin open 5 THER+ Thermistor + Note 3 6 THER- Thermistor - Note 3 7 NC Keep this pin open 8 C2 LED Cathode 9 A2 LED Anode

10 NC Keep this pin open



Note3:Thermistor description Item Value Remarks Type NCP18XH103F0SRB Murata

Resistance Tolerance 10kΩ±1% Ta=25℃

Temperature Characteristic Nominal B-Constant 3350-3399K Ta=25 to +85℃

Permissive Operating Current 0.31mA Ta=25℃ Absolute Maximum Power

Consumption 100mW Ta=25℃

The relationship of temperature-resisitance as the following form:

Figure 5.4.1 NTC Resistance VS Ambient Temperature( Center Value)

5.5 Input Clock and Data Timing

DD=3.3V Ta=25℃

Parameter Symbol Min Typ Max Unit Conditions

VDD Power ON Slew rate Tpor 20 ms RSTB pulse width Trst 50 us DCLK=50MHZ DCLK Frequency Fclk - 33.3 50.0 MHZ DCLK Cycle Time Tcph 20 - - ns DCLK Pulse duty Tcwh 40 50 60 % VS Setup Time Tvst 8 ns VS Hold Time Tvhd 8 - - ns HS Setup Time Thst 8 ns HV Hold Time Thhd 8 - - ns Data Setup Time Tdsu 8 ns R0~R7,G0~G7,B0

~B7 to DCLK Data Hold Time Tdhd 8 - - ns R0~R7,G0~G7,B0

~B7 to DCLK DE Setup Time Tesu 8 ns DE Hold Time Tshd 8 - - ns

Table 5.5.1 AC Electrical Characteristics



Figure 5.5.2 Input Clock and Data timing Diagram

5.6 Recommended Timing Setting Of TCON

VDD=3.3V Ta=25℃

Parameter Symbol Value Unit Horizontal display area thd 800 DCLK

DCLK frequency @ Frame rate =60Hz fclk Min. Typ. Max.

- 29.2 50 MHz 1 Horizontal Line th 908 928 1088

DCLK HSYNC pulse width thpw 1 48 87 HSYNC back porch thb 88 88 88 HSYNC front porch thfp 20 40 200 DE mode Blanking Th-thd 108 128 288

Vertical display area tvd 480 H VSYNC period time tv 517 525 712 H VSYNC pulse width tvpw 1 1 3 H VSYNC back porch tvb 31 31 29 H

VSYNC Front porch (tvfp) tvfp 5 13 200 H DE mode Blanking Tv-tvd 37 45 232 H

Table 5.6.1 Horizontal and Vertical input timing

Figure 5.6.2 Vertical input timing Diagram



Figure 5.6.3 Horizontal input timing Diagram 5.7 Enter and exit standby mode sequence

Figure 5.7.1 Enter and exit standby mode sequence 5.8 Power on/off sequence

Figure 5.8.1 Power ON sequence Figure 5.8.2 Power OFF sequence



6. Optical Characteristics （Ta=25℃）

Item Symbol Condition Min Typ Max Unit Remark

View Angles

θT

CR＞10

50 60 -

Degree Note2,3 θB 60 70 -

θL 70 80 -

θR 70 80 -

Contrast Ratio CR θ=0o 600:1 900:1 - - Note 3

Response Time Tr +Tf 25℃ - 20 40

ms Note 4,9 -20℃ - - 400

Chromaticity

White x

Backlight is on

0.285 0.325 0.365 - Note 1,5

y 0.308 0.348 0.388

Red x 0.551 0.591 0.631

- Note 1,5 y 0.312 0.352 0.392

Green x 0.311 0.351 0.391

- Note 1,5 y 0.559 0.599 0.639

Blue x 0.110 0.150 0.190

- Note 1,5 y 0.074 0.114 0.154

Uniformity U White(max brightness) 75 80 - % Note 6

NTSC - - 45 55 - % Note 5

Luminance L - 500 600 - cd/m2 Note 7

Test Conditions: Note 1: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 5 Minutes operation, the optical Properties are measured at the center point of the LCD screen by CS2000, LCD5200, CA310.

Item Field Contrast Ratio

1° Luminance

Chromaticity

Lum Uniformity Response Time 2°

500mm

Photo detector Field

LCD Panel TFT-LCD Module

The center of the screen



Note 2: Definition of viewing angle range and measurement system. Viewing angle is measured at the center point of the LCD by LCD5200。

Note 3: Definition of contrast ratio

The contrast ratio is measured at the center point of the LCD by CS2000. Note 4: Definition of Response time The response time is defined as the LCD optical switching time interval between “White” state and “Black” state. Rise time (Tr) is the time between photo detector output intensity changed from 10% to 90%. And fall time (Tf) is the time between photo detector output intensity changed from 90% to 10%. Response time is measured at the center point of LCD by LCD5200. Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD by CS2000. Note 6: Definition of homogeneity Active area is divided into 9 measuring areas automatically by CS2000. Every measuring point is placed at the center of each measuring area.

Homogeneity = Lmin/ Lmax L-------Active area length W----- Active area width

Lmax: The measured Maximum luminance of all measurement position. Lmin: The measured Minimum luminance of all measurement position.

Note 7: Definition of luminance : Measure the luminance at center point of LCD by CS2000.



5

7. Reliability Test Items and Criteria

No Test Item Test condition Criterion

1 High Temperature Storage 95℃±2℃ 500H RH<=45% Restore 2H at 25℃ non-operation

Note1,Note6,Note7 IEC60068-2-1,GB2423.2

2 Low Temperature Storage -40℃±3℃ 500H Restore 2H at 25℃ non-operation

Note1, Note7,IEC60068-2-1 GB2423.1

3 High Temperature Operation 85℃±2℃ 500H RH<=45% Restore 2H at 25℃ operation

Note1,Note6,Note7, IEC60068-2-1 GB2423.2

4 Low Temperature Operation -30℃±3℃ 500H Restore 2H at 25℃ operation

Note1, Note7,EC60068-2-1 GB2423.1

5 High Temperature & Humidity Operation

60℃±2℃, 90±2%RH 500H operation

Note1,Note3, Note4 Note6,Note7, IEC60068-2-78 GB/T2423.3

6 Thermal Shock -40°C(30min)→ change→+85°C(30min) Change Time:5min,100cycle non-operation

Note1, Start with cold temperature End with high temperature, IEC60068-2-14,GB2423.22

7 ESD

Contact discharge: C=150pF,R=330Ω± 5 point/panel Contact: +/-8KV,5times Air discharge: +/-15KV, 5times (Environment:15℃~35℃, 30%~60%.86Kpa~106Kpa)

Note2,Note5, IEC61000-4-2 GB/T17626.2

8 Mechanical Shock Test

100 x 9.8m/s2, t=6ms, XYZ directions, Half sin curve, [non-operating],each directions 3 times

Note2

9 Vibration Test

Frequency: 8 - 33.3 Hz, Total amplitude: 1.3mm Frequency: 33.3 - 400 Hz, Acceleration: 29.4 m/s² sweep time: 15 minutes 2 hours each for X and Z directions, 4 hours for Y direction (total 8 hours) non-operation

Note2,IEC60068-2-6 GB/T2423.10



Notes: 1. The test result shall be evaluated after the sample has been left at room temperature and humidity for 2 hours without load. No condensation shall be accepted. The sample will not be accepted if appear these defects: 1) Air bubble in the LCD 2) Seal leak 3) Non-display 4) Missing segments 5) Glass crack 6) CR reduction >40% 7) IDD increase >100% 8) Brightness reduction >50%

2. The samples of these tests will not be accepted if appear these defects: 1) Air bubble in the LCD 2) Seal leak 3) Non-display 4) Missing segments 5) Glass crack

3. Each test item applies for a test sample only once, the test sample cannot be used again in any other test item. 4.For Damp Proof Test, Pure water(Resistance＞10MΩ) should be used. 5. In case of malfunction defect caused by ESD damage, if it would be recovered to normal state after resetting, it would be judge as a good part. 6 In the test of High Temperature Operation and High Temperature & Humidity Operation ,the operation temperature is the surface temperature of module 7. We will consult with our customers, if appearing problems during the reliability test.



8. Mechanical Drawing



9. Product Inspection Criteria 9.1 Inspection Conditions

9.1.1 Ambient conditions: a. Temperature: Room temperature 25±5℃ b. Humidity: (60±10) ％RH c. Circumstance Illumination（Light to the surface of LCD） Backlight-on 100-300Lux Backlight-off 800-1200lux

9.1.2 Viewing distance The distance between the LCD and the inspector’s eyes shall be 35cm or more.

9.1.3 Viewing Angle U/D: 45º/45º, L/R: 45º/45º

9.1.4 Light-on condition The current of the Backlight should refer to the recommended typical value in this specification.

9.1.5 Definition of LCD zone (with Bezel)

A-zone: The inside of the Active Area (as defined on the product drawing) B-zone: The inside of the Viewing Area which is between A-zone and the metal frame (defined on the product drawing if no up metal frame) C-zone: Whole of the LCD Module except the zone A and B. (Including FPC& Metal Frame & backside of the LCD Module)



9.2 Cosmetic Inspection Criteria

Inspection Item

Inspection Standards

Acceptable Qty.

Applied Zone

Inspection Mode Note

Dark /Bright spots

(The bright spots should

not visible through ND5%)

φ≤0.2 Ignore

A Backlight-on

0.2 ﹤φ ≤ 0.4 3

0.40﹤φ None

Bright pixel dot

1 sub-pixel, Visible through ND5%

None A Backlight -on

Dark pixel dot 1 sub-pixel

3 (distance≥10

mm) A Backlight -on

Lints & Scratches

W≤0.03 and L≤3.0 Ignore

A\B Backlight -on Backlight -off

0.03﹤W≤0.05 and L≤3.0 2

0.05﹤W or L>3.0 None

Polarizer Dent/Bubble

φ≤0.2 Ignore

A\B Backlight -on Backlight -off

0.2 ﹤φ ≤ 0.4 3

0.40﹤φ None

Mura Visible through ND2% at full black pattern None A Backlight -on

Dirty\Dust (The surface of Polarizer)

Those wiped out easily are acceptable A\B Backlight -off \



10. Package Method

dust proof bag

package Quantity:

One tray include: 4 PCS moudleOne Carton include: 4 x10=40 PCS moudle

Use enpty tray

put products into the 10 trays

Rotate tray 180 degrees and place on top of stack,check the trays using Fig.A.

Use package bag

Carton

EPE1

EPE2EPE3

EPE1

Use the tape to seal carton,40 PCS LCMs per carton A

DETAIL A

TRAY 1TRAY 2TRAY 3

TRAY N

Use strap

+

+One unit(Use strap)

Dessicant

Documents

FOR AUTOMOTIVE LCD MODULE - TianMa