For Electrical & Plumbing Contractors - Ramset … Concrete, Hollow Block Wall, Reinforced Concrete, Reinforced Prefabricated Concrete Electronic Fuel Injection Lithium Battery Battery

12 www.ramset.com.au 1300 780 063

CableMaster™800For Electrical & Plumbing Contractors

Features & Benefits• Battery Gauge – Helps avoid running out of battery power.• Fuel Cell Gauge – Always know when to change fuel cells.• Lithium Battery – Fast Charge, Long Life• Tool-less Depth of Drive Adjustment• Power Saving Technology – isolates battery when tool is not in use• Compact design with 20 pin magazine – Allows the tool to fit in tight spaces• Easily removable fastener guide and magazine• Greater tool clearance – Allows the tool to fit in close to edge applications.• Removable Support Leg – Ensures tool is at 90° to work surface for

optimum fixings• Electronically controlled fuel injection – Ensures consistent power in a wide

temperature range.• Low Maintenance. Designed to work in all conditions.

Gas

Tech

nolo

gy S

yste

ms

DescriptionThe RamsetTM CableMasterTM800 is the most technologically advanced gas tool on the market. The new CableMasterTM800 offers a number of innovative features allowing quicker, safer installation of a wide variety of clips for plumbing, data and electrical installations. The speed at which the CableMasterTM800 is able to perform installations provides tremendous savings in total installed cost.

Related ProductsDrive Pins & Fuel CellsContractor Packs

SpecificationsWeight 3.8kgHeight 309mmLength 396mm

Magazine Capacity20 (+3) pin magazine, [50 (+3) pin magazine accessory]

Impact Force 82JActuation Pressure 5kgOverdrive 4mmIntermittent Operation 2 pins per secondFuel Cell Life 750 pins (approx)Battery Charge Capacity 3,000 pins (approx)Battery Voltage 3.7V Lithium-IonBattery Charge time 90mins (25mins for 500 fixings)Power Regulation AutomaticOperating Temperature Range -5°C to 49°CSubstratesConcrete, Composite Steel Decking, Solid Brick, Precast Concrete, Steel Pre-stressed Concrete, Hollow Block Wall, Reinforced Concrete, Reinforced Prefabricated Concrete

ElectronicFuel Injection

Lithium Battery

Battery & Fuel Gauge

Removable20 Pin Magazine

(50 Pin Magazine Available)

Depth of Drive adjustment Compact &

Lightweight Design

www.ramset.com.au 1300 780 063 13

CableMaster™800For Electrical & Plumbing Contractors

AccessoriesPart No Description Order Qty018543 Pulsa 800 20 Pin Magazine 1018544 Pulsa 800 50 Pin Magazine 1018545 Pulsa 800 Lithium-ion Battery 1018546 Pulsa 800 Lithium-ion Battery Charger 1014641 Pulsa 800 Magnetic Washer Adaptor 1018423 CableMasterTM800 Fastener Guide 1018424 TrakFastTM800 Fastener Guide 1B20544L Gas Tool Degreaser and Lubricant 1PA1613 Safety Glasses 1

Gas Technology Systems

Standard Operating ProcedureAlways read and understand the instruction manual before attempting to operate a Ramset™ Gas Technology Tool.1. First insert the fuel cell and battery into the tool.2. Insert the collated fasteners into the magazine.3. The clip should then be placed on the end of the fastener guide without compressing the front end of the tool.4. The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface).5. Once the tool is compressed the trigger can be actuated and the fastener is driven into the substrate securing the clip in place.

CableMaster™ 800Part No Description Order

QtyCABLEMASTER800 CableMaster™ 800 Pulsa™ Gas Tool + 2 x Lithium-Ion Batteries 1

Kit includes: CableMaster™ 800™ tool, high impact carry case, 2 x batteries, battery charger, safety glasses and instruction manual

Trades & Applications Plumbing Electrical Fire & Contractor Contractor SecurityPermanent cable suspension to concrete and steel 4

Pipe suspension systems to concrete and steel 4

Fire and security cabling to concrete and steel 4

Temporary cable suspension to concrete and steel 4

AU ONLY


CableMaster™800Consumables

Heavy Duty Pin Range for Steel and Hard Concrete FixingDrive Pins designed for fastening to standard strength concrete, masonry and steel.

SpecificationsRaw Material Carbon SteelCorrosion Protection Zinc Electroplated (Minimum coating 5µm)Nominal Head Diameter 6.3mmNominal Shank Diameter 2.6mm (C620 Stepped shank 2.6/2.2mm)Shear Strength 1120N/mm2

Tensile Strength 1800N/mm2

Hardness 52-56HRC

Gas

Tech

nolo

gy S

yste

ms

Ramset™ recommends application test on-site before commencing use.

Pulsa 800 Part No

Original Pulsa 700Part No

Description Length Order Qty

P8HC615 HC615 Heavy Duty Steel/Concrete 15mm 500

P8HC617 HC617 Premium Hard Concrete/Steel 17mm 500

P8HC622 HC622 Premium Hard Concrete/Steel 22mm 500

P8HC627 S011409 Premium Hard Concrete/Steel 27mm 50010 strip collation (suitable for use in 40 and 50 pin magazines) + 1 x Fuel Cell

NZ ONLY


CableMaster™ Consumables

ClipElec™ 4 4 4 4 4 4

DataLec™ Clip 4 4 4 4 4 4 4

CTClip™ 4 4 4 4 4 4

EClip™ 4 4 4 4

Threaded Rod Hanger 4 4 4 4

FP FireFix™ Clip 4 4

CableHorn™ Double & Single 4

Direct Alignment Half Saddle 4 4 4

Strap & Plate Mounting Washer 4

Catenary Wire Bracket 4 4

Application Type

CableMaster™800Consumable Selection Guide

4Recommended


Data Cable

Strap, Plates & Fixtures

Light Duty Cable Tray

Flexible/Plastic Pipe

Catenary W

ire

Electrical Conduit

Cable Fixing

Small Diam

eter Rigid Pipes

M

etal Pipes

M

etal/Nylon Straps

Fire &

Service Cabling


AU ONLY

AU ONLY

AU ONLY

AU ONLY


Gas

Tech

nolo

gy S

yste

ms

ClipElec™


ClipElec™ All-purpose Cable Tie ClipsPulsa 800 Part No


Description Order Qty

P8CPGCL CPGCLClipElec™ Contractor Pack(500 x clips, HC622 Pins, Fuel Cell, Cable Ties 200mm x 4.8mm Black)

1

P8CPGCLHC617 CPGCLHC617ClipElec™ Hard Concrete Contractor Pack(500 x clips, HC617 Pins, Fuel Cell, Cable Ties 200mm x 4.8mm Black)

1

Features & Benefits• ClipElec™ can be used for cable, conduit and tube work.• Universal design allows cable ties up to 9mm wide.• Designed with an in-built energy absorber for perfect embedment.• Clips directly onto the CableMaster™ Pin Guide for one handed operation.• Hands are a safe distance from the Pin Guide during installation.• Can be used with the PulsaLift™ Pole to fix from the ground.• Optional plug and screw installation.

Specifications

Raw MaterialPolypropylene copolymer, high impact, halogen free. UV resistant

Capacity Up to 9mm cable tie width.Spacing Recommendation 0.5 & 1 metre (approx)

Fire Resistance Properties

Incandescent wire test (regulation NFC 20-455) 750°C passed - LCIE laboratory test results N° 438 309 (December 1998)

Low Temperature Test No breakage at 0°CDimensions 32 x 37mm

*NOTE: Test concluded when clip pulled over pin head or cable tie failed. Job-site testing may be required to determine actual achievable job-site values. Results have been achieved with a CableMaster™ tool set at minimum overdrive setting. Accessories failing to fix correctly should be removed and a new fixing set away from any spalled concrete. Tension loads provided are for static load situations only. Values represent a minimum factor of safety of 3:1 on the lowest test results achieved. Minimum edge distance 75mm, minimum spacing between fixings 50mm. Tension loads are per fixing, however a minimum of 3 fixings per fastening unit should be used.

DescriptionClipElec™ is an all purpose cable tie system that may be used for fixing cable, conduit and pipes for a wide variety of electrical and plumbing applications. This system is extremely versatile allowing for many different sized cables, pipes and conduit to be secured. The ClipElec™ all purpose cable tie system may be used with the 4.8mm supplied cable ties or with other cable ties up to a maximum width of 9mm.

Installation Procedure1. Simply clip the ClipElec to the tool pin guide.2. Press against the substrate, press the trigger & the clip is fixed.3. Install the tube or conduit with cable tie.

Pin Selection Guide Substrate HC617 HC622Hard Concrete >50MPa 4 4

Concrete <50MPa 4 4

Hollow Concrete Block k 4

Steel 4 4

Steel Decking 4 4

4Suitable kPossible

Performance Table*

PinLoad Capacity (Tension) - Concrete

Cable Tie Width 20MPa 32MPaP8HC617 9mm 10kg 12kgP8HC622 9mm 10kg 12kgP8C620 4.8mm 2.5kg 3.7kg


AU ONLY


CTClip™

Pulsa 800 Part No


Description Pipe / Conduit Diameter Order Qty

P8CPGCT CPGCTCTClip™ Contractor Pack Standard (500 x clips, HC622 Pins, Fuel Cell)

16 - 32mm 1

Performance Table*Load Capacity (Tension) - Concrete

Pin 20MPa 32MPaP8HC617 7kg 9kgP8HC622 7kg 10kg

SpecificationsRaw Material High impact, Nylon 66Spacing Recommendation 0.5 & 1 metre (approx)Fire Resistance Properties UL94HB Fire Test

DescriptionThe CTClip™ is the all in one cable tie system. With the integral cable tie the CTClip™ can be used for cable, conduit and tube work.

Installation Procedure1. Side mount clip into pin guide.2. Press against work surface. Fire tool.3. Install the cable or conduit/tube as required. Fasten tie strap.

Pin Selection GuideSubstrate HC617 HC622Hard Concrete >50MPa 4 4

Concrete <50MPa 4 4


Steel 4 4

Steel Decking 4 4

4SuitablekPossible

CTClip™


*NOTE: Test concluded when clip pulled over pin head or cable tie failed. Job-site testing may be required to determine actual achievable job-site values. Results have been achieved with a CableMaster™ tool set at minimum overdrive setting. Accessories failing to fix correctly should be removed and a new fixing set away from any spalled concrete. Tension loads provided are for static load situations only. Values represent a minimum factor of safety of 3:1 on the lowest test results achieved. Minimum edge distance 75mm, minimum spacing between fixings 50mm. Tension loads are per fixing, however a minimum of 3 fixings per fastening unit should be used.


Features & Benefits• CTClip can be used for cable, conduit and tube work.• Maximum cable cluster or tube diameter of 63mm.• Clip base raised above work surface.• In-built energy absorber for optimum pin penetration.• Side mount clip into pin guide.• One handed installation.• Fix from the ground with the PulsaLift™ Pole.• Optional plug and screw installation.



Gas

Tech

nolo

gy S

yste

ms

DataLec™ClipMulti-purpose Data & Cable Clip

Datalec™ Multi-purpose Data & Cable clips Pulsa 800 Part No



P8CPGDLHC617 CPGDLHC617

DataLec™ Clip Contractor Pack (Heavy duty pins 17mm)(500xclips,HC617pins,cable ties 200x4.8mm Black, Fuel cell)

1

P8CPGDLHC622 CPGDLHC622

DataLec™ Clip Contractor Pack (Heavy duty pins 22mm)(500xclips,HC622pins, cable ties 200x4.8mm Black, Fuel cell)

1

VEL1225Hook and loop strap 12mm x 25metre Roll (optional extra)

1

Features & Benefits• One clip for data and standard cable installations• Multiple cable mounting positions• Wide soft Hook & Loop Strap (12mm) or hard plastic tie compatible• Parallel or multi-directional cable fixing• Single and cable bundle installations• Non abrasive support and protection of services • Suits cable in conduit and small diameter pipe applications• Fix to standard and hard concrete, hollow masonry block & steel formwork

SpecificationsRaw Material HDPE, High impact ,Halogen free Slot opening 14mm wide Clip spacing recommendation from 0.3 to 1mtr (approx.) depending

on applicationDimensions (mm) 33W x33D x 14H

*NOTE: Testing concluded when clip pulled over pin head or strap/tie failed .Job site testing may be required before use to determine actual achievable job site values. Results have been achieved using a CableMasterTM tool set at minimum overdrive setting. Accessories failing to fix correctly should be removed and a new fixing set away from any spalled concrete. Tension load capacities are for static load situations only. Values shown represent a minimum factor of safety of 3:1 against the ultimate capacity. Minimum edge distance 75mm, minimum spacing between fixings 50mm. Tension loads are per fixing, a minimum of 3 fixings should be used per fastened unit. 1. Tested with Pricemark Cable Tie, # CT-76380NAT100 2. Tested with Hook & Loop Strap - 12mm Hook & Loop Strap 60mm overlap with 50mm diam bundle.

DescriptionDataLec™ Clip is a Multipurpose data and cable clip for the fast installation of specialised and standard cables. Install Fibre Optic, Broadband, Cat5/6, Audio visual and other specialised cables using soft Hook & Loop Strap to correctly support and secure these cables without damage. For standard electrical and power cabling installations hard plastic cable ties or soft Hook & Loop Strap can be used to suit installation needs. This versatile and strong clip design is suitable for the installation of multiple cable bundles, multi-directional cable runs, small diameter conduits with cables and plastic/metal pipes.

Pin Selection Guide Substrate HC617 HC622Hard Concrete >50MPa 4 4

Concrete <50MPa 4 4


Steel 4 4

Steel Decking 4 4

4Suitable kPossible

Performance Table*

WidthConcrete compressive strength

20MPa 40MPaCable Tie (supplied) 4.8mm 5kg 7kgCable Tie1 7.6mm 12kg 15kgHook & Loop Strap2 12mm 3kg 4kg


Installation Procedure1. Gently insert clip mounting tip (centre of clip) into CableMaster™ tool nosepiece2. Press clip against substrate, depress CableMaster™ tool nosepiece and fix clip3. Attach cable to DataLec™ clip with appropriate tie or strap for the application

Optional Item VEL1225

Total tensile load capacity per DataLecTMClip - HC617 or HC622 Pins


DataLec™ClipMulti-purpose Data & Cable Clip


Plastic pipe or conduit Electrical cable bundles

Multiple data cable bundles Fibre optic cable in conduit

Electrical cable Data cable bundles

Fibre optic cable Electrical cable


Gas

Tech

nolo

gy S

yste

ms

EClip™ CableMaster™ Consumables

Performance TableTube extraction loads at 22°CForce required to manually remove tube from the clip

Clip Size Average Ultimate Load (approx)16mm 4kg20mm 6kg25mm 8kg

Pin Selection GuideSubstrate HC617 HC622 Hard Concrete >50MPa 4 4

Concrete <50MPa 4 4


Steel 4 4

Steel Decking 4 4

4SuitablekPossible

DescriptionThe EClip™ is ideal for firmly securing conduit, HDPE, and PVC pipe. Once installed, the clip is able to be rotated to allow for precise positioning of rigid and flexible tube. The design of the EClip™ incorporates interlocking connections to allow for multiple clips to be joined together side by side for a professional finish.

SpecificationsRaw Material

High quality polypropyleneHalogen free. Fire resistant

Spacing Recommendation 0.5 and 1 metre (approx)

EClip™ Conduit ClipPulsa 800 Part No


Description Pipe / Conduit Diameter

Order Qty

P8CPGEC16 CPGEC16 Contractor Pack (500 x clips, HC622 Pins, Fuel Cell) 16mm 1P8CPGEC20 CPGEC20 Contractor Pack (500 x clips, HC622 Pins, Fuel Cell) 20mm 1P8CPGEC25 CPGEC25 Contractor Pack (500 x clips, HC622 Pins, Fuel Cell) 25mm 1

Installation Procedure1. Side mount the EClip™ onto the tool Pin Guide.

2. Fixing is quick and precise.

3. When fixed, it can be easily rotated around the pin to adjust its position.


Features & Benefits• The EClip™ is designed to clip easily onto the CableMaster™ Pin Guide from the side allowing one-handed operation.• Hands are a safe distance from the Pin Guide during installation.• Fixing is precise.• After installation the EClip™ can be rotated around the pin to adjust alignment.• The slotted design of EClip™ absorbs energy, preventing the pin head from splitting the clip.• The hollow structure of the EClip™ gives flexibility for easy insertion of conduit.• EClip™ incorporates male/female connections allowing multiple conduit installation side by side.• Optional plug and screw installation.

AU ONLY


Threaded Rod HangerPulsa 800 Part No


Description Thread Diameter Order Qty

P8CPGTRH CPGTRHThreaded Rod Hanger Contractor Pack (400 x hangers, HC617 Pins, Fuel Cell)

M8 - M10 1


Threaded Rod HangerCableMaster™ Consumables

SpecificationsRaw Material Carbon SteelMaterial Thickness 1.5mmCoating Zinc Electroplated (Min. Coating 7µm)

Installation Procedure1. Insert TRH laterally onto CableMaster™ pin guide to the

stop position.2. Install the TRH. The pin guide will automatically remove itself

from the channel. If the guide is stuck inside the channel, gently move the tool

laterally to release it.3. Screw in the threaded rod, (two possible diameters) and

bend the TRH to the vertical position using the rod or Bend the TRH by hand if you intend to use a suspended hanging system, small chain or steel wire.

Pin Selection GuideSubstrate HC617 HC622Hard Concrete >50MPa 4 k

Concrete <50MPa 4 k

Hollow Concrete Block 4 4

Steel 4 k

Steel Decking 4 4

4SuitablekPossible


32MPaTRH with HC617 Pulsa™ Pin 15kg

*NOTES:

1. Values represent the maximum recommended working load in tension.

2. A minimum of 4 fastenings per fastened unit must be used.

3. Results have been achieved with a CableMaster™ tool.

4. All visible failures must be replaced and a new fixing set away from any spalled concrete.

5. Tension loads provided are for static load situations only.

6. Job-site testing may be required to determine actual achievable job-site values.

7. Pins must be sufficiently set, such that the underside of the head of the pin is in contact with the surface.

TyMaster™ powder actuated tool installationsFor heavy duty applications refer to Z Bracket rod Hanger (M10) Page 52.This is a rod hanger assembly for TyMaster™ powder actuatedtool installations.

DescriptionFor light duty applications the Threaded Rod Hanger bracket is an ideal alternative to traditional anchors such as the DynaSet™ drop-in anchor. The bracket features an M8 and a M10 thread allowing for a choice of threaded rod sizes in applications such as light duty cable tray and pipe suspension. The bending movement used during application acts as a self testing mechanism for the quality of the fixing.


Features & Benefits• Slide-on channel for pin guide. Lateral insertion for fast, safe installation.• Thick steel with reinforcing ribs for extra strength.• Dual threads. Less parts, more flexibility.• Optional drill and 6mm anchor installation.• Electro zinc coating protects against corrosion.


Gas

Tech

nolo

gy S

yste

ms

FP FireFix™ ClipsCableMaster™ Consumables

FireFix™

Pulsa 800 Part No


Description Cable Outer Diameter

Order Qty

P8CPGFPO2 CPGFPO2FireFix™ Clip Contractor Pack (500 x clips, HC617 Pins, 5 Fastener Guide Adaptors)

7 - 8.1mm 1

P8CPGFPO4 CPGFPO4FireFix™ Clip Contractor Pack (500 x clips, HC617 Pins, 5 Fastener Guide Adaptors)

8 - 9.5mm 1

DescriptionThe FP FireFix™ clip fire cable installation system has been developed for installing the specialised fire protection cable required for the safe operation of essentail service equipment during fire emergencies. This system consists of the FP FireFix™ clip installed with a Pulsa™ pin using the CableMaster™ Pulsa™ gas tool.

Features & Benefits• Complies to AS1530.4• Fixes fire rated cables ten times faster than traditional drilling methods• Clip manufactured from 316 Stainless Steel powder coated• Simply clips shut holding the cable(s) securely. 2 cables per clip• Can be used with stainless steel cable ties to install larger cables• Fast fixing to non combustible materials such as solid concrete, hollow

concrete block and steel Two hour fire protection system for essential services.

• Utilises a plastic adaptor that fits on the CableMaster™ Pin Guide allowing one-handed installation.

• Hands are a safe distance from the Pin Guide during installation.• Can be used with the PulsaLift™ Pole to fix from the ground.• Holds one or two cables. Choice of two sizes.• Simply clips shut holding the cable(s) securely. 2 cables per clip.

Installation Procedure1. Fit adaptor to the CableMaster™ pin guide.

2. Position the FP FireFix™ clip

3. Push the tool against the substrate and fix the

FP FireFix™ clip in place.NOTE: remove battery from the tool when fitting the FP FireFix™ adaptor.

Pin Selection GuideSubstrate HC617 HC622 Hard Concrete >50MPa 4 4

Concrete <50MPa 4 4


Steel 4 4

Steel Decking 4 4

4SuitablekPossible

SpecificationsRaw Material Stainless SteelCoating Powder coated red


Fire Standards ComplianceWhen independently tested in accordance with the requirements of the Fire Test Method for Supports & Fixings of AS/NZS 3013:1995 appendix B, “Electrical Installations – Classification of the Fire & Mechanical Performance of Wiring Systems”, the FP FireFix Cable Clip (when fixed to the concrete slab via a Ramset 20mm Heavy Duty Concrete SC6 Gas Pin or HC617 Pin) was found to be able to support a static load of 1kg. Fire test reports are available upon request.

AU ONLY



CableHorn™ FixingPulsa 800 Part No


Description Fixing Capacity Order Qty

P8CPGCH140 CPGCH140CableHorn™ Contractor Pack (200 x fixings, HC622 Pins, Fuel Cell)

8 Cables (3 x 1.5mm2) 1

P8CPGCH CPGCHCableHorn™ Contractor Pack (125 x fixings, SC620 Pins, Fuel Cell)

16 Cables (3 x 1.5mm2) 1

CableHorn™


Features & Benefits• Designed for use with electrical, data and communication cables.• Replaces the need for cable tray and catinary wire.• Clips directly onto the CableMaster™ Pin Guide allowing one-handed

operation.• Can be used with the PulsaLift™ Pole to fix from the ground.• Add or remove cables as required.• In-built energy absorber for perfect embedment.• Large fixing base for better stability.• Flexibility in installation-vertical, horizontal, overhead.• Optional plug and screw installation.

Pin Selection GuideSubstrate HC622 Hard Concrete >50MPa 4

Concrete <50MPa 4

Hollow Concrete Block 4

Steel 4

Steel Decking 4

4SuitablekPossible

Installation Procedure1. Simply clip the CableHorn™ to the tool pin

2. Press against the substrate (5kg to actuate the tool) press the trigger to fix.

3. Install the cable simply by lifting the edge of the CableHorn™.

*NOTE: Test concluded when clip pulled over pin head or pin failed. Job-site testing may be required to determine actual achievable job-site values. Results have been achieved with a CableMaster™ tool set at minimum overdrive setting. Accessories failing to fix correctly should be removed and a new fixing set away from any spalled concrete. Tension loads provided are for static load situations only. Values represent a minimum factor of safety of 3:1 on the lowest test results achieved. Minimum edge distance 75mm, minimum spacing between fixings 50mm. Tension loads are per fixing, however a minimum of 3 fixings per fastening unit should be used.

DescriptionIn many applications the use of the CableHorn™ system can eliminate the need for cable trays to be installed. Cables may be added or removed after the CableHorn™ is installed. When used in conjunction with the PulsaLift™ pole system, CableHorns™ may be installed from the ground without the need for ladders or scissor lifts.

Specifications

Capacity

Single CableHorn™: 8 cables, 3 x 1.5mm2 maximum.Double CableHorn™; 16 cables, 3 x 1.5mm2 maximum

Spacing Recommendations Between 0.60m and 1.50m

Raw MaterialHigh impact modified Pa66 Halogen free polypropylene.

Fire Resistance PropertiesIncandescent wire test (IEC 695): 650 °C UL94 HB (ISO 1210): 100 mm/min

Low Temperature Tests No breakage at 0 °CQuality Certificate TUV certificate ISO 9001

DimensionsSingle CableHorn™: Length 137mm. Double CableHorn™: Length 228mm

Fixing BaseSingle CableHorn™: 19.5 x 38.5mm. Double CableHorn™: 19.5 x 24.3mm


Pin 20MPa 32MPaHC622 18kg 20kg


AU ONLY


Direct Alignment Conduit Half SaddlesPulsa 800 Part No


Description Pipe / Conduit Diameter Order Qty

P8CPGDAS20 CPGDAS20Direct Alignment Saddle Contractor Pack (400 x saddles, HC617 Pins, Fuel Cell)

20mm 1

P8CPGDAS25 CPGDAS25Direct Alignment Saddle Contractor Pack (400 x saddles, HC617 Pins, Fuel Cell)

25mm 1

Conduit Half SaddleCableMaster™ Consumables

DescriptionConduit Half Saddles are suitable for fixing conduit and metal pipes. Standard Half Saddles may be used with the CableMaster™ tool in conjunction with a Saddle Adaptor. Direct Alignment Saddles make the job even faster by clipping directly onto the fastener guide.


Concrete <50MPa 4 4


Steel 4 4

Bondeck 4 4

4SuitablekPossible

Installation Procedure1. Gently place saddle assembly into end of pin guide.

2. Place saddle over conduit/tube.

3. Depress nose piece against work surface, fire tool.

Features & Benefits• FAST accurate fixing of conduits and tubes to concrete,hollow block, & steel.• Fits directly to nose piece of CableMaster™ Pulsa™ gas tool• Precise hole alignment.• Optimum pin penetration and strength.• Neat and flush finish.• One hand installation.• Optional drill and 5mm anchor installation.• Site test recommended for use in critical applications.

SpecificationsRaw Material Carbon SteelMaterial Thickness 1.6mmCoating Zinc Electroplated (Min. Coating 7µm)

Direct Alignment Conduit Half Saddles

Gas

Tech

nolo

gy S

yste

ms



Strap/Plate WasherCableMaster™ Consumables

Strap and Plate WasherPart No Description Order QtySPMW Strap and Plate Washer 500

SpecificationsSteel type CA2S-E.

Steel Thickness1.6mm providing a high resistance to deformation.

Nominal Diameter 16mm

Installation Procedure1. Gently place washer assembly into end of nose piece.

2. Place assembly tip in position.

3. Depress nose piece against work surface, fire tool.

DescriptionThe Strap and Plate Washer may be used in a wide variety of applications where thin materials or fixtures with existing holes need to be quickly fastened. Common applications where the Strap and Plate washer are used include securing thin metal, nylon and Hook & Loop straps for ducting, cable bunches and other fixtures. Brackets with existing pre-drilled holes for traditional mechanical fasteners can be secured with the use of strap and plate washers.


Concrete <50MPa 4 4


Steel 4 4

Steel Decking 4 4

4SuitablekPossible

Features & Benefits• FAST One-Step Fixing of metal, nylon and Hook & Loop straps for

ductwork, cable bunches and fixture installations.• Suitable to span wide mounting holes in cable suspension brackets or

switchboxes up to 8mm diam.• To reinforce mounting holes in brackets and prevent fixture pullover.• Precise hole alignment.• Use with pre-drilled or solid straps and plates.• Suitable for use with CableMaster™ Pulsa™ collated pins.• Choose the pin length to suit the application.• SC6 or HC6 pins recommended.• One handed fixing to concrete, hollow block and steel.




Catenary Wire Bracket AssemblyPulsa 800 Part No



P8CPGCWB CPGCWBCatenary Wire Bracket Contractor Pack (400 x brackets, HC617 Pins, Fuel Cell, 200mm x 4.8mm Black)

1

Catenary Wire BracketCableMaster™ Consumables

SpecificationsSteel type CA2S-E.

Steel Thickness2mm providing a high resistance to deformation.

Nominal Fixing Hole Diameter 7.5mm

DescriptionReinforced steel angle bracket, with closed eye for catenary wire and cable installations when fixing to concrete, concrete block and steel. Suitable for light to medium duty, close to ceiling applications.


Concrete <50MPa 4 4


Steel 4 k

Steel Decking 4 4

4SuitablekPossible

Installation Procedure1. Place bracket assembly into the pin guide.

2. Depress pin guide against work surface, fix bracket

into position.

3. Attach cables and wires as required.

Features & Benefits• For catenary wire, cable, and hanger rod installations when fixing to

concrete, hollow block and steel.• Improved clampdown to work surface with dimpled baseplate.• Optimum pin penetration with cushioned base.• Strengthening ribs reduce bracket twist and deformation.• Rounded edges to prevent cable damage.• Three methods of installation. - Fast fixing with CableMaster™ Pulsa™ gas tool.

- TyMaster™ tool installation (See page 52).

- Traditional drill and anchor method.

• Suits light to medium duty fixing applications. (see performance table)

• Fix from the ground with pole tool.• Eye size - 7mm.

Performance Table*Load Capacity (Tension)

Product - Concrete 32MPaCat Brkt Pulsa assembly, HC617 Pin 14kg

*Notes:1. Values represent the maximum recommended working load in tension.2. A minimum of 5 fastenings per fastened unit must be used.

3. Results have been achieved with a CableMaster™ tool.4. All visible failures must be replaced and a new fixing set away from any spalled concrete.5. Tension loads provided are for static load situations only.6. Job-site testing may be required to determine actual achievable job-site values7. Minimum edge distance 75mm. Minimum spacing between fixings 50mm.


Documents

For Electrical & Plumbing Contractors - Ramset … Concrete, Hollow Block Wall, Reinforced Concrete, Reinforced Prefabricated Concrete Electronic Fuel Injection Lithium Battery Battery