FOR NOT - bsintek.basco.combsintek.basco.com/BriggsDocumentDisplay/gkjrtCXCnfBhU7y.pdf · FOAM TIRES Reduces chance for flat tires and also adds weight to the machine NOT 601 FOR

AEH Owner’s Manual

Part No 362500 1 362500_C_HI

HYDRO AERATOR Owner's Manual AE1300H

Beginning Serial #: 020216001

Accessories

Original Instructions

IMPORTANT- READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE.

SOLID SPIKE TINE

Complete set of spike tines for the AE’s arms.

P/N 362611

TINE KIT

Individual coring tine for replacement of worn or broken tines.

P/N 360100

CHARIOT KIT

Allows the user to ride behind the unit. Saving fatigue from walking.

P/N 362609

FOAM TIRES

Reduces chance for flat tires and also adds weight to the machine

P/N 362601 NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

2

CONTENTS

SPECIFICATIONS AND SAFETY 3 INSTRUCTION LABELS 4 PACKING CHECKLIST & ASSEMBLY 5 OPERATION 6 MAINTENANCE 7-9 TROUBLESHOOTING 10 ILLUSTRATED PARTS & PARTS LIST 11-22

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

3

SPECIFICATIONS

AE1300H

Engine: HP 13 (9.7 kW)

Engine: Model GX390UTQA2

Engine: Type Honda OHV

Engine: Fuel Capacity 6.4qt. (6.1 L)

Engine: Oil Capacity 1.16 qt. (1.1 L)

Total Unit Weight: 516# (234 Kg)

Max. operating slope 20o

SAFETY

WARNING

This product can expose you to chemicals including gasoline engine exhaust, which is known to the State of California to cause cancer, and carbon monoxide, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. Read the safety rules and follow them closely. Failure to obey these rules could result in loss of control of the unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

4

INSTRUCTION LABELS The labels shown below were installed on your BILLY GOAT® Aerator. If any labels are damaged or missing, replace them before operating this equipment. Part numbers from the Illustrated Parts List are provided for convenience in ordering replacement labels. The correct position for each label may be determined by referring to the part numbers shown.

LABEL WARNING GUARDS LABEL EXPLOSIVE FUEL LABEL HIGH PRESSURE P/N 900327 P/N 400268 P/N 362506

LABEL DUMP VALVE LABEL HYDRAULIC INST LABEL WARNING GUARDS P/N 501504 P/N 362507 P/N 400424 LABEL HOT SURFACE P/N 100258 LABEL INSTRUCTIONS AE P/N 362501

ENGINE LABELS

HONDA

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

5

PACKING CHECKLIST Your Billy Goat is shipped from the factory in one carton, completely assembled.

PUT OIL IN ENGINE BEFORE STARTING

ASSEMBLY

READ all safety instructions before assembling unit. TAKE CAUTION when removing the unit from the box.

1. CHECK engine oil level and fill to proper level. 2. CONNECT spark plug wire. Set the engine stop switch to the ON position. You will use the stop switch on the

handle during operation.

Boxing Parts Checklist

Owner’s Manual AE1300H 362500 Engine Manual Per Model

Honda 13 HP

PARTS BAG & LITERATURE ASSY Warranty card P/N- 400972, Owner’s Manual P/N-362500, General Safety and Warnings Manual Renovation-100295.

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

6

CONTROLS

Forward Drive Lever

Tine Engage Lever Operator Presence

On/Off Switch

Reverse Drive Lever

Pull Start

Parking Brake

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

7

OPERATION

AERATING OPERATION

NOTE: NEVER PARK THIS UNIT ON A SLOPE OF ANY KIND. Always keep tines in the up position when parking the unit. TINES RAISING/LOWERING: The tines are raised or lowered into the ground by operating the tine engagement lever on the right of the machine. When engaging the ground, be sure that lever cams over and locks into place. Tine penetration is very dependent on surface preparation. When removing the tines from the engagement position, make sure the lever fully cams over into the forward position for transport. READ the entire operation section before aerating. ENGAGE TINES: With the aerator in the work area, lower the tines into the ground with the tine lowering lever and engage the tine lever on the left hand side of the handle.

SPEED: It is recommended for proper aerating performance that the engine be operated at maximum RPM. Control ground speed using the forward/reverse drive levers. Speed is proportional to the extent the levers are actuated.

AERATE: With the tines engaged, engage either the forward or reverse drive lever for the desired direction of travel. Note: Core spacing on this machine is determined by speed. The faster you travel the further the spacing between cores pulled and vice versa. NOTE: The hydraulic system may seem sluggish until the oil reaches a normal operating temperature.

PARKING BRAKE: To set the parking brake, push the lever located on the rear of the engine base down and to the right so that it catches. To release the brake, simply push the lever back down and slide it to the left. When the lever is to the right, the parking brake is on. When the lever is to the left the parking brake is off. TRANSPORT: Be sure to lift the tine engagement lever (tines out of the ground) before transporting away from the work area. LIFTING AND TIE DOWN: DO NOT Lift this unit. Tie down points are located on the frame with labels. Always secure the unit at tie down points before transporting to job site.

*****TIPS***** MOW

Mow the lawn to its normal cut height. WATER

For the best performance and maximum tine penetration the lawn should be thoroughly watered the day before aeration. INSPECT

Check the lawn before beginning work. Remove all rocks, wire, string, or other objects that can present a hazard during work prior to starting. IDENTIFY

Mark all fixed objects to be avoided during work, such as sprinkler heads, water valves, buried cables, or clothes line anchors, etc. SLOPES

Do not operate the aerator on steep slopes. Use extreme caution when operating on any sloped surface. For lesser sloped areas operate the unit, traversing up and down at a 45 degree angle to the slope rather than straight across. Extended operation on steep slopes can cause engine damage. NOTE: DO NOT release the operators clutch bail when operating on a slope. This will allow the unit to free wheel and allow the unit to roll down the slope. NOTE: Honda engines are equipped with a low oil sensor to prevent engine damage. When it senses a low oil condition (i.e. unit is operating or sitting on a steep slope) the engine shuts down. The maximum operating slope for the engine is 200. The low oil condition must be corrected before the engine can be restarted. See the engine owner’s manual for more information.

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

8

MAINTENANCE

PERIODIC MAINTENANCE Periodic maintenance should be performed at the following intervals:

Maintenance Operation Every Use (daily)

Every 10 hrs

Every 25 hrs Every 50 Hours

Inspect for worn or damaged parts

Check for loose parts

Check engine oil

Thoroughly clean all debris from unit and tine arms

Oil chains (see lubrication)

Lubricate speed control cables and linkage

Lubricate clutch control cable and linkage

Check Hydraulic oil

Grease front caster assemblies

Inspect belt for wear

Check rear tire pressure FOR INFORMATION REGARDING SERVICE INTERVALS FOR ENGINE, REFER TO SUPPLIED ENGINE MANUAL ENGINE MUST BE LEVEL WHEN CHECKING OR FILLING OIL

SERVICING HYDRAULIC SYSTEM

NOTE: DO NOT SERVICE HYDRAULIC SYSTEM WHEN IT IS HOT. WARNING: Due to the dangerous potential of fluid injection, you should always use a piece of paper to check for hydraulic leaks rather than using your fingers.

READ all safety instructions before servicing unit.

DISCONNECT spark plug wire before servicing unit.

1. To check the hydraulic oil level, twist the breather cap on the oil tank counter-clockwise ¼ turn and remove. When looking inside the filler hole, you should fill the tank so that you can just see oil start to cover the bottom of the internal strainer. Use 20W-50 engine oil for normal operating temperatures and for colder climates switch to 15W-40. An excellent choice for colder climates is Mobil 10W-40 Synthetic oil. Over-filling the tank will result in excess oil sloshing out of the breather during operation.

2. To change the oil filter it is advisable to clamp the hose from the tank prior to loosening the filter in order to prevent excessive spilling of hydraulic oil.

3. Remove filter by un-screwing counter-clockwise from filter base.

4. When replacing filter (Billy goat P/N 362396), it is recommended to spread a thin coat of oil on the rubber gasket of

the filter prior to re-installing.

5. After the rubber gasket seats, turn an additional 2/3 turn. See page 22 for Hydraulic Schematic.

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

9

NOTE: Items in ( ) can be referenced in the Parts Illustrations and Parts Lists on pages 12-23.

INDIVIDUAL TINE REPLACEMENT (See page 14 and 15 for Parts Illustration and Parts list)

1. While it is possible to replace only one tine at a time, it is recommended to replace tines in pairs on a tining arm. 2. To replace tines, simply remove the 3/8” bolt that passes through the tining arm assembly. In this way, the tines can

be removed from the arm by sliding outward from the tining arm. 3. Remove the worn or broken tines from the assembly. 4. Inspect the bolt for wear, straightness, or thread damage. If the bolt is damaged, it should be replaced. This bolt is a

Grade 8 fastener. Replacing with a weaker bolt is not recommended. 5. To re-install, place a washer on the tine holder and then a tine onto the bolt. Now install these onto the tining arm

with the open side of the tine facing the rear of the machine. Once the bolt is through the tining arm, place another tine on the bolt, then a tine holder. Finally, install a washer and nylon inserted lock nut. Tighten the assembly. Be careful not to over tighten which will bend the tine holders.

NOTE: Tines are a normal wear item and should be inspected regularly for signs of wear or damage.

BELT AND CHAIN TENSION ADJUSTMENT



ADJUSTING BELT TENSION (See page 12 and 13 for Parts Illustration and Parts list)

1. Proper belt tension needs to be maintained to prevent slippage during operation. When bail is fully actuated the length of the coiled portion of the clutch cable spring should be 1.75”.

2. If the clutch cable spring needs adjustment, loosen the jam nuts holding the cable on the handle assembly and adjust

the cable either in or out to shorten or lengthen the spring.

3. Once proper adjustment is reached, tighten the jam nuts.

4. Once adjustment is made, re-install spark plug wire and test adjustment. The machine hydraulic pump and transaxle should dis-engage when the bail is released. There should be no evidence of belt slippage (reduced ground speed or slow tine RPM) when operating the machine with bail engaged.

NOTE: Never release the clutch on a slope. The unit is heavy and will free wheel downhill.

NOTE: A worn belt will not allow for proper adjustment and must be replaced. ADJUSTING CHAIN TENSION (See page 14 and 15 for Parts Illustration and Parts list)

1. Remove the hood (item 4) by removing the seven bolts, washers, and lock washers. (items 111,119,128), that secure it to the tining frame.

2. Locate the bolt (item 31, 33) and nut (item 80) that hold each chain idler sprocket to the tining frame of the unit. One idler sprocket sets tension on the left tine drive chain and one sets tension on the right tine drive chain.

3. Loosen the bolt and nut and slide the idler sprocket (item 29) in the desired direction.

INCREASED TENSION: Slide the sprocket up. DECREASED TENSION: Slide the idler sprocket down.

4. Tighten the bolt and nut to secure the sprocket in place.

5. Replace the hood and reinstall the seven bolts, washers, and lock washers that secure it in place.

NOTE: Over tensioning the chain will cause premature chain and sprocket wear. DO NOT OVER TENSION THE CHAIN. A properly tensioned chain will have slack of 3/8"-1/2" when moved by hand.

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

10

DRIVE BELT REPLACEMENT (See page 12 and 13 for Parts Illustration and Parts list)



1. Disconnect spark plug wire.

2. Loosen four screws (item 112) holding belt cover (item 10) and remove the cover.

3. Examine condition of belt. Look for cracks, splits, delamination or damage to outer covering. Any of these things might warrant replacement.

4. If the idler is not providing enough tension inspect the clutch cable spring (item 231) underneath the handle. This spring body should stretch to a length of 1.75” when the operator presence handle is actuated. If not enough tension is being put on the spring this could mean a stretched belt, but most likely the cable needs adjusted. Simply loosen the jam nuts holding the cable on the handle assembly and adjust the cable either in or out to shorten or lengthen the spring. Re-tighten nuts and check spring stretch.

5. Replace belt cover (item 10) and secure with screws removed earlier.

6. Reconnect spark plug wire.

7. Check belt tension by operating unit under conditions that caused belt slippage. If belt continues to slip it may require replacement before operation may continue.

CHAIN REPLACEMENT (See page 14 and 15 for Parts Illustration and Parts list)

1. Remove the hood (item 4) by removing the seven bolts, washers, and lock washers. (items 111,119,128), that secure it to the tining frame.

2. Locate the bolt (items 31, 33) and nut (item 80) that hold each chain idler sprocket to the tining frame of the unit. One idler sprocket sets tension on the left tine drive chain and one sets tension on the right tine drive chain.

3. Loosen the bolt and nut and slide the idler sprocket (item 29) to the bottom of the slot in the bracket.

4. Locate the master link in the chain and remove.

5. When installing new chain make sure that the inner crank arm is lined up with the inner crank arm of the opposite

side. In operation, the two inner tining arms move together and the two outer tining arms move together. Any other timing of the arms will result in unsatisfactory performance of the machine.

6. Once new chain is installed, replace the hood and reinstall the seven bolts, washers, and lock washers that secure it

in place.

NOTE: Over tensioning the chain will cause premature chain and sprocket wear. DO NOT OVER TENSION THE CHAIN. A properly tensioned chain will have slack of 3/8"-1/2" when moved by hand.

CHAIN LUBRICATION (See page 14 and 15 for Parts Illustration and Parts list)

1. Remove the top guard by removing the four nuts, two on each side that secures it to the frame. 2. Apply a light coat of No. 30 Oil or a penetrating chain lubricant to keep the chain clean and in good running order. 3. Replace the guard and reinstall the four screws that secure it in place.

NOTE: If machine is cleaned with a pressure washer the chains should be lubricated after each cleaning.

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

11

TROUBLESHOOTING

When servicing engine refer to specific manufacturer’s engine owner's manual. All engine warranty is covered by the specific engine manufacturer. If your engine requires warranty or other repair work contact your local servicing engine dealer. When contacting a dealer for service it is a good idea to have your engine model number available for reference (See table page 3). If you cannot locate a servicing dealer in your area you can contact the manufacturer’s national service organization. To reach: American Honda: 800-426-7701 WARRANTY CLAIM PROCEDURE

Should a BILLY GOAT® machine fail due to a defect in material and/or workmanship, the owner should make a warranty claim as follows:

The machine must be taken to the dealer from whom it was purchased or to an authorized Servicing BILLY GOAT Dealer.

The owner must present the remaining half of the Warranty Registration Card, or, if this is not available, the invoice or receipt.

The Warranty Claim will be completed by the authorized BILLY GOAT Dealer and submitted to their respective BILLY GOAT Distributor for their territory Attention: Service Manager. Any parts replaced under warranty must be tagged and retained for 90 days. The model number and serial number of the unit must be stated in the Warranty Claim.

The distributor service manager will sign off on the claim and submit it to BILLY GOAT for consideration.

The Technical Service Department at BILLY GOAT will study the claim and may request parts to be returned for examination. BILLY GOAT will notify their conclusions to the distributor service manager from whom the claim was received.

The decision by the Technical Service Department at BILLY GOAT to approve or reject a Warranty Claim is final and binding.

Make sure that the product is registered with Billy Goat. For online product registration go to www.billygoat.com

Problem Possible Cause SolutionEngine will not start Stop switch off (Honda only). Throttle in off

position. Engine not in full choke position. Out of gasoline. Bad or old gasoline. Spark plug wire disconnected. Dirty air cleaner. Engine oil level too low (Honda only).

Check stop switches, throttle, choke position and gasoline. Connect spark plug wire. Clean or replace air cleaner. Or contact a qualified service person. Check and fill engine oil.

Abnormal vibration Damaged or missing tines. Loose handle bolts. Loose engine bolts.

Stop work immediately. Replace any damaged or missing tines. Tighten all loose bolts and nuts.

Engine stalls or labors when aerating

Working on too steep of a slope. Not enough oil in the engine. Hydraulic oil not up to operating temperature

Work at 45 degrees to the slope moving up and down instead of across. Check and add engine oil. Allow for hydraulic oil to reach operating temperature

Engine is locked, will not pull over

Debris locked against reel, or drive pulleys. Engine problem.

Pull spark plug wire and remove debris. Contact an engine servicing dealer for engine problems.

Unit does not move when clutch is engaged

Belt drive out of adjustment. Worn drive belt. Loose or damaged chain or sprockets. Loose or damaged pulleys. Damaged or broken clutch cable. Transmission bypass set in free-wheel

See maintenance on pg. 8 of this manual. Contact a qualified servicing dealer. Set transmission bypass in drive

NOT FOR REPRODUCTIO

N

http://www.billygoat.com/


Part No 362500 362500_C_HI

12

AE1300H PARTS DRAWING ENGINE

252253

158

231

175

188

191

155

157

178187186185

190

128114

102

171

114

158

89

83

250

135

140124

91

172113

172113

76

117

170

133189

150

173

112

135

128124

93

101174

132

251128

52

27 5

17

4718

37

26 12

10

53

362

90

128

114

1

128

169

62

254

157

255256

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

13

AE1300H PARTS LIST ENGINE

Item No. Part No. Description Qty1 362602 ENGINE BASE WA 12 430366 ENGINE HONDA GX390 13 HP 15 362225 PUMP PK 12cc VARIABLE DISPLACEMENT 110 362327 GUARD BELT AE900 112 362337 BELT HP GP AMD EFF. LENGTH 64.04" 117 362111 PLATE PUMP MOUNT 118 362275 PULLEY 5.00" OD FLAT IDLER 126 362303 PULLEY 4.75 OD X .591 ID 5L 127 362116 ARM ENGAGE PUMP WA 136 812238 SPACER ENGINE WA DL18 137 362391 PULLEY 4.50" OD X 1.00 ID 5L 147 362112 IDLER ARM WA AE900 152 362372 ROD PUMP ENGAGE 153 362406 SPACER ENGINE CRANKSHAFT 162 362332 TRANSAXLE AE900 176 362280 END ROD SLIDING 183 351278 SPHERICAL ROD END MSF-5 189 351277 SPHERICAL ROD END MSM-5 190 8041054 SCREWCAP 3/8"-16 X 2" HCS ZP 491 362279 HOSE HYDRAULIC W#10 JIC 293 362415 SPACER .75 OD X 11 GA 1

101 510213 SCREWCAP 7/16" - 20 X 1" HCS GR 8 W/PATCH 1102 800242 SPRING EXTENSION 1112 890359 SCREW SELF TAP 1/4"-20 X 5/8" HWH TYPE F 6113 900471 PIN HAIR 1/4" ZP 3114 8160002 NUT LOCK 5/16"-18 HEX ZP 9117 9201113 KEY 1/4" SQ X 1.00" 1124 8160003 NUT LOCK 3/8"-16 3128 8171003 WASHER 5/16" FLAT ZP 12132 440153 WASHER 1.5" OD X .453 ID X .25" THK 1133 8177012 WASHER LOCK 3/8" S/T MED 4135 362254 BUSHING .500" ID 4140 8172009 WASHER 3/8" SAE 2150 370128 SCREWCAP M6 X 14 1155 8041004 SCREWCAP 1/4" - 20 X 3/4" GR 5 HCS ZP 8157 8160001 NUT LOCK 1/4"-20 HEX ZP 9158 8041028 SCREWCAP 5/16" - 18 X 1" GR 5 HCS ZP 4169 8041031 SCREWCAP 5/16" - 18 X 1 3/4" GR 5 HCS ZP 4170 8041052 SCREWCAP 3/8" - 16 X 1 1/2" HCS ZP 2171 8142002 NUT 5/16"-18 HEX ZP 1172 8171002 WASHER 1/4" FLAT ZP 6173 8172019 WASHER FLAT FENDER 1/4" 2174 8177013 WASHER LOCK 7/16" S/T MED 1175 900230 WASHER 1/2" FLAT KD WHEEL MTG 1178 8172007 WASHER 1/4" SAE 13185 362330 BRACKET GUARD FAN 1186 362331 GUARD WIRE PUMP FAN 1187 362325 COOLER OIL 1188 362380 KEY FEATHER 5MM X 5MM X 30MM 1189 370120 WASHER SPLIT M6 2190 370120 BELT FINGER AE900 2191 362351 KIT FAN GUARD 1231 362276 CABLE CLUTCH BELT AE900 1250 8161041 NUT LOCK 5/16"-18 LT WT TH ZP 1251 8161042 NUT LOCK 3/8"-16 LT WT TH ZP 1252 440124 PIN CLEVIS 0.25 X 0.50 1253 371275 1/4" RUE RING 1254 862318 BRACKET BELT GUILD UPPER 1255 8041010 SCREWCAP 1/4"-20 X 2" HCS ZP 1256 900455 NUT WHIZ 1/4"-20 WASH FACE 1

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

14

AE1300H PARTS DRAWING TINE

114140

268

137

111

113

112

269267

114

151

140

260

259

137158

260

261

104

224

245

8

48

13

148

19

38

55

8667

99

107

104 78

110

137

139

107242

242

4

82

29

39

31

8588 91

9138

141117

105114

84

140

248

248

140

14

94 72

3071137108

109

114

133132

134

258

31

140

124

147

179

52111

129 142

116

119

121

121116

119

98

134

140

58

203

106

38

202

199

111

128

201

198

200

227

246

246

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

15

AE1300H PARTS LIST TINE

Item No. Part No. Description Qty

4 362605 HOOD AE900 18 362606 TINE ARM ASSY RIGHT AE900H SERVICE 2

362603 TINE ARM ASSY LEFT AE900H SERVICE 2

9 362233 MOTOR TINE DRIVE 1

13 362104 CRANK DRIVING WA AE900 2

14 360100 TINE CORING 3/4 8

19 362103-PAINT ARM CRANK WA AE900 2

29 362117 SPROCKET DRIVE AE900 1

30 362382 LINK CAST AE1300H 8

31 362243 BEARING AND FLANGETTE ASSY 1.00 538 362148 TINE ARM WA 1

39 362105 SHAFT DRIVE TINE WA AE900 1

48 362227 SHAFT CRANK AE900 2

52 362372 ROD PUMP ENGAGE 1

55 362261 SPROCKET 13T #50 IDLER 2

58 362101 FRAME TINING AE900 1

67 362282 BRACKET REAR HOOD 1

70 362281 BRACKET FRONT HOOD MOUNT 2

71 362220 BEARING AND SHAFT 872 362407 HOLDER TINE AE900 16

78 501302 BEARING 1" SEALED PRESS IN 2

82 430303 LABEL PRODUCT DECAL LG CIRCLE 1

84 790167 SCREWCAP 3/8"-24 X 2 3/4" GR 8 W/PATCH 8

85 400424 LABEL WARNING OPEI 2

86 360124 SPACER TINE IDLER 1.175" 2

88 900327 LABEL WARNING DANGER 2

91 362279 HOSE HYDRAULIC W#10 JIC 294 362232 SCREWCAP 3/8"-16 X 5 3/4" GR 8 4

98 362288 KEY #15 HI PRO 1

99 362246 SPACER SPINDLE BEARING AE900 2

104 362205 MACHINE BUSHING 1" X 1 1/2" X 14 GA 6

105 8024039 CARRIAGE BOLT 5/16" - 18 X 3/4" ZP 9

106 362284 WASHER ADHESIVE BACKED ISOLATION 7


107 362212 RING RETAINING EXTERNAL 1.00" 4

108 610305 NUT LOCK 1/2" - 20 THIN 16

109 8041039 SCREWCAP 5/16"-18 X 4"" HCS ZP 8

110 831272 SCREWCAP 5/16"- 24 X 2 1/4" GR 8 W/PATCH 4

111 8041026 SCREWCAP 5/16"-18 X 3/4" GR 5 HCS ZP 5

112 890359 SCREWCAP SELF TAP 1/4"-20 X 5/8" HWH TYPE F 2

113 900471 PIN HAIR 1/4" ZP 1

114 8160002 NUT LOCK 5/16"-18 HEX ZP 14

116 8160005 NUT LOCK 1/2"-13 HEX 4

117 9201113 KEY 1/4" SQ X 1.00" 5

119 8177011 WASHER LOCK 5/16" S/T MED 11

121 8172011 WASHER 1/2" SAE ZP 4

124 8160003 NUT LOCK 3/8"-16 4

128 8171003 WASHER 5/16" FLAT 7

129 8041102 SCREWCAP 1/2"-13 X 3" HCS ZP 2

132 440153 WASHER 1.5" OD X .453 ID X .25" THK 4


134 350346 NUT 5/16"-18 SER HEX FLNG ZP 18

137 8172008 WASHER 5/16" SAE ZP 40

138 362278 SHCS 1/2"-13 X 1.750" ZP 2

139 8149002 NUT LOCK 5/16" - 24 FIN HEX ZP 4

140 8172009 WASHER 3/8" SAE 9

141 362289 SHCS 5/16"-18 X 1.25 BLK OX 1

142 8171006 WASHER 1/2" USS 4

147 810932 SCREWCAP 3/8"-24 X 2 1/4" GR 8 W/PATCH 8

148 900154 SCREWCAP 3/8" - 24 X 1" HCS GR 8 4

151 8197031 PIN COTTER 1/8" X 1" ZP 2

158 8041028 SCREWCAP 5/16"-18 X 1" GR 5 HCS ZP 4

198 362504 LABEL BADGING RISER 1

199 362502 LABEL BADGING SIDE 2

200 362503 LABEL BADGING FRONT 1

201 362506 LABEL WARNING HIGH PRESSURE 1

202 362507 LABEL INSTRUCTION HYDRAULIC 1

203 362258 CHAIN #50 X 70 PITCHES O-RING 2

224 400173 VIBRATION MOUNT 5

227 362416 SPACER 1.25 OD X 1.010 ID .258 LONG 1

242 9201109 KEY 1/4" SQ X 0.75" 4

243 362323 NUT LOCK 3/8"-24 HEX ZP 16

245 100258 LABEL HOT SURFACE 1

246 362607 SPRING ASSY AE900H 4

248 362323 NUT LOCK 3/8-24 16

258 362362 BOLT CARRIAGE 5/16"-18 X 1" ZP SHRT NK 12

259 362143 HOOD BRACKET FRONT AED 1

260 362142 HOOD HINGE AEH 2

261 381716 PIN CLEVIS 3/8" X 2" STAINLESS STEEL 2

267 362393 HOOD LIFT ROD 1

268 362394 HOOD GUIDE BRACKET UPPER 1

269 362144 HOOD GUIDE BRACKET LOWER 1

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

16

AE1300H PARTS DRAWING DRIVE

262 266

263

124265264

121

244

7

114

65

146

126

2033

41

183108

20

62

64

131177137

114

130249 151

134

83176 235

171

89158

11

135

153182

87

103

145144149

158157

124

128

137105

116

120

118

123

9222

42

43

195

114

1

192

194 137

196

233

228

12

247

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

17

AE1300H PARTS LIST DRIVE


1 362100 ENGINE BASE WA 1

7 362352 WHEEL 15" X 6.00 - 6 TURF SAVER 2

11 362106 CAM SPEED CONTROL WA AE900 1

20 362329 BRACKET TRANSAXLE MOUNT 4

22 362107 BRACKET CASTER WA AE900 1

33 362118 SKID PLATE WA 1

41 362306 BRACKET BELT GUIDE LOWER AE900 1

42 373300 WHEEL, 8" X 3" HEAVY DUTY 2

43 371102 CASTER RIG WA SC 2

62 362332 TRANSAXLE AE900 1

64 362356 ROD BYPASS TRANSAXLE 1

65 362418 SPACER REAR WHEEL AE900H 2

83 351278 SPHERICAL ROD END MSF-5 1

87 501114 BELL CRANK BC2600 WA 2

89 351277 SPHERICAL ROD END MSM-5 1

92 520184 BUSHING FLANGE 1" OD 3/4" ID 4

103 351257 BEARING .500 ID X 1.125 OD X .313 THK 2

105 8024039 BOLT CARRIAGE 5/16" - 18 X 3/4" ZP 8

108 610305 NUT LOCK 1/2" - 20 THIN 1

114 8160002 NUT LOCK 5/16"-18 HEX ZP 18

116 8160005 NUT LOCK 1/2"-13 HEX 2

118 520176 RING RETAINING EXTERNAL 3/4" 2

120 8041108 SCREWCAP 1/2" -13 X 4 3/4" HCS ZP 2

121 8172011 WASHER 1/2" SAE 4

123 610363 ZERK GREASE FITTING 2

124 8160003 NUT LOCK 3/8"-16 7

126 850230 RETAINING RING E 3/4" 2

128 8171003 WASHER 5/16" FLAT 1

130 362341 ANTI ROTATION ROD 1

131 351264 SER HEX WSHR FLNG SCREW 5/16"-18 X 3/4" 8


135 362254 BUSHING .500" ID 2

137 8172008 WASHER 5/16" SAE ZP 17

144 351348 SPACER SPEED CONTROL EYELET 2

145 8041008 SCREWCAP 1/4"-20 X 1 1/2" HCS ZP 2

146 850238 WASHER .765" ID X 1.25" OD X .06" 2

149 351347 SPACER SPEED CONTROL STEPPED 2

151 8197031 PIN COTTER 1/8" X 1" ZP 1

153 351258 BOLT SHOULDER 3/8" X 1 3/4" 2

157 8161040 NUT LOCK 1/4"-20 LT WT TH ZP 2

158 8041028 SCREWCAP 5/16" - 18 X 1" GR 5 HCS ZP 1

171 8142002 NUT 5/16"-24 HEX ZP 1

176 351419 SPACER ENGINE SIDE 1


182 840078 BUSHING 3/8" ID X 1/2" OD X 3/8" LONG 4

183 362398 PULLEY DIA. 6.00 CUPPED 26 TOOTH SPLINE 1

192 351324 SPRING TRANSAXLE RETURN 1

194 440193 PIN CLIP HITCH 0.051 X 3/4" 1

195 9201092 KEY 3/16" SQ X 3.00 2

196 8172015 WASHER 3/4" SAE 2

235 8041030 SCREWCAP 5/16"-18 X 1 1/2" HCS ZP 2

244 501504 LABEL DRIVE RELEASE 1

247 362608 CASTER ASSY AE900H 2

249 8172005 WASHER #10 SAE 1

262 520031 BOLT SHOULDER 1/2" X 2" 1

263 510142 SPRING TRANS IDLER 1

264 381157 SPRING EXTENSION 3/4" OD X 1-3" 1

265 362449 PARKING BRAKE BRACKET 1

266 362146 PARKING BRAKE LEVER 1

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

18

AE1300H PARTS DRAWING HANDLE

240 35137

239

61

154

40232

231

24

233

233

10083

238

158237

236182

229

230

114

135234235

124

134

105

134

40

128

124

135

155

105

119119 111

114

105

112

66

115124

75

25

46

24

16

54

5160

3444

23

74

6

3

1

245

176

257

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

19

AE1300H PARTS LIST HANDLE



3 362604 HANDLE WA 1

6 362134 TANK OIL WA AE900H 1

16 362396 FILTER SPIN ON 1

23 362119 BRACKET LH HANDLE MOUNT WA 1

24 351209 MAGURA CONTROL 2

25 362267 BAIL ASSY AE900 1

34 351269 RUBBER DEFLECTOR 1

35 362269 SPHERICAL ROD END FEMALE 5/16"-24 LFT 1

40 520087 GROMMET 1" HOLE 4

44 351268 BAR CLAMP DEFLECTOR 1

46 500267 GRIP HANDLE 1" X 5.5" 2

51 371210 RUBBER HANDLE MOUNT 2

54 362395 MOUNT OIL FILTER 1

60 362292 GUARD TRANSAXLE FRONT 1

61 362129 BELL CRANK BAIL WA 1

66 351200 BRACKET CLUTCH CABLE OS900SP 1

74 362120 BRACKET RH HANDLE MOUNT WA 1

75 362342 RESERVOIR CAP 1

83 351278 SPHERICAL ROD END MSF-F 1

100 890132 PLUG TUBE INSERT 1" OD 2



112 890359 SCREW SELF TAP 1/4"-20 X 5/8" HWH TYPE F 6

114 8160002 NUT LOCK 5/16"-18 HEX ZP 7

115 8024058 CARRIAGE BOLT 3/8"-16 X 1" ZP 6


124 8160003 NUT LOCK 3/8"-16 8

128 8171003 WASHER 5/16" FLAT ZP 2


135 362254 BUSHING .500" ID 4

137 8172008 WASHER 5/16" SAE ZP 2


155 8041002 SCREWCAP 1/4" - 20 X 1/2" HCS ZP 2


176 351419 SPACER ENGINE SIDE 1

182 362501 LABEL INSTRUCTION AE900H 1

229 362441 SWITCH ENGINE KILL TOGGLE 1

230 360218 NUT PAL 3/8" 1

231 362276 CABLE CLUTCH BELT AE 1

232 520092 GROMMET 1.25" HOLE 1

233 362312-S CABLE SPEED CONTROL ASSY 2

234 362121 BELLCRANK CABLE WA 1

235 8041030 SCREWCAP 5/16" - 18 X 1 1/2" GR 5 HCS ZP 1

236 362274 HARNESS WIRE KILL SWITCH 1

237 362322 NUT 5/16"-24 LEFT HAND FIN HEX ZP 1

238 362266 JACKSCREW 5/16"-24 RT AND LFT 1

239 8149002 NUT 5/16"-24 FIN HEX ZP 2

240 362505 LABEL INGROUND TURNING LOGO 1

245 100258 LABEL HOT SURFACE 1

257 8050057 SHCS 10-32 NF 1/2" SS 6

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

20

AE1300H PARTS DRAWING LIFT

146

197

56

114

95

105

96 133141

158119152156

140124

148

133132

127

225

117

162

142

111

108

156

162

152127

124

132

160

108 124159

143

100

77

5021

59

4615

68

6332

80

58

1

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

21

AE1300H PARTS LIST LIFT



15 362410 HANDLE TINE WA 1

21 362223 BEARING LIFT 2

32 362259 BRACKET HANDLE SUPPORT 2

46 500267 GRIP HANDLE 1" X 5.5" 1

50 362108 TINE FRAME LIFT SHAFT WA 1

56 362245 BEARING AND FLANGETTE ASSY .75" 2

58 362101 FRAME TINING AE900 1

59 362127 LIFT ARM LFT WA AE900 1

63 362125 ARM LIFT RT WA AE900 1

68 360298 BUMPER RECESS 2

77 362128 ARM TINE LIFT CONNECTING WA LH 1

80 362126 ARM TINE LIFT CONNECTING WA RH 1

95 8041166 SCREWCAP 3/4" - 10 X 2 1/2" LG ZP 2

96 8161006 NUT LOCK 3/4" - 10 ZP 2

100 890132 PLUG TUBE INSERT 1" OD 1


108 610305 NUT LOCK 1/2" - 20 THIN 3


114 8160002 NUT LOCK 5/16"-18 HEX ZP 6

117 9201113 KEY 1/4" SQ X 1.00" 8


124 8160003 NUT LOCK 3/8"-16 4

127 360183 BUSHING PIVOT FRAME AE 4

128 8171003 WASHER 5/16" FLAT ZP 2

132 440153 WASHER 1.5" OD X .453 ID X .25" THK 2


140 8172009 WASHER 3/8" SAE 2

141 8049070 SHCS 5/16"-18 X 1.25 BLK OX 4

142 8171006 WASHER 1/2" USS 1

143 8041055 SCREWCAP 3/8" - 16 X 2 1/4" HCS ZP 2

146 850238 WASHER .765" ID X 1.25" OD X .06" 2

148 900154 SCREWCAP 3/8" - 24 X 1" HCS GR 8 2

152 441150 WASHER 1.125" OD X .344" ID X .25 THK 2

156 362257 BUSHING TINE FRAME PIVOT 2

158 8041028 SCREWCAP 5/16" - 18 X 1" GR 5 HCS ZP 2

159 8171004 WASHER 3/8" FC 2

160 520028 SCREWCAP 1/2" -20 X 1 1/4" GR 5 W/PATCH 3

162 362286 WASHER NYLON 6

197 362113 TINE ENGAGE HANDLE MOUNT WA 1

225 362419 WASHER 33/64 I.D. X 1.50" OD X .25 THK 1NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

22

AE1300H PARTS DRAWING PUMP

6

112

91

9

62

5

222

219221

206

207 210208

211212209211

212211

212

217

220

218

241

216

220

212

220

216

211

213

223215

220

214

91

187

205

226

169

NOT FOR REPRODUCTIO

N


Part No 362500 362500_C_HI

23

AE1300H PARTS LIST PUMP


5 362225 PUMP PK 12cc VARIABLE DISPLACEMENT 1

9 362233 MOTOR TINE DRIVE 1

91 362279 HOSE HYDRAULIC W#10 JIC 2

112 890359 SCREW SELF TAP 1/4" - 20 X 5/8" HWH TYPE F 1

169 8041032 SCREWCAP 3/8" - 16 X 1 2" HCS ZP 1

187 362325 COOLER OIL 1

205 362231 FITTING 10MJ - 10MOR STR 1

206 362420 FITTING TEE 6803-06-06-06 1

207 362423 HOSE ASSY #6 JIC TO RAW 11.00" LONG 1

208 362230 FITTING 10MF 0- 8MORB STRAIGHT 2

209 362426-S HOSE, HYDRAULIC 1/2" X 12.00" LONG 1

210 362421 FITTING 45 DEG 6802-06-04 W/0.050" ORIFICE 1

211 362309 FITTING 08HB - 08MORB STRAIGHT 4

212 362311 CLAMP MINIATURE WORM GEAR MAH6 4

213 362425 HOSE HYDRAULIC 3/8" X 46.00" LONG 1

214 790170 HOSE CLAMP 1

215 362320 FITTING 90 DEG FEMALE TO FEMALE 1

216 362234 FITTING 06HB - 06MORB STRAIGHT 2

217 362422 HOSE ASSY #6 JIC TO RAW 13.00" LONG 1

218 362424-S HOSE HYDRAULIC 3/8" X 19.00" LONG 1

219 362300 PLATE CLAMP COVER 1

220 362310 CLAMP MINIATUE WORM GEAR MAH4 4

221 362299 BODY PROFILED CLAMP 2

222 362013 HYDRAULIC HOSE CLAMP 1

223 362321 3/8" HOSE BARB 1

226 362315 04MORB - 02MP STRAIGHT 1

241 362427-S HOSE HYDRAULIC 1/2" 14.00" LONG 1

NOT FOR REPRODUCTIO

N

Documents

FOR NOT - bsintek.basco.combsintek.basco.com/BriggsDocumentDisplay/gkjrtCXCnfBhU7y.pdf · FOAM TIRES Reduces chance for flat tires and also adds weight to the machine NOT 601 FOR