FS30 Installation

FS30 InstallationFS30 Installation

2

INSTALLATION OVERVIEW

Syrup BIB Injected Flavor BIB

Injected Flavor BIB Pumps Syrup BIB Pumps

CO2

Front Syrup, Water & CO2 Connections

CO2

Brand Syrups (5 to 1 ratio)Injected Syrup Flavors (20 to 1 ratio)

WaterWater


Barb unions and reducers connect lines to Bundle tubing

3/8” line

1/4” line 75 psi 75 psi CO2 SourceCO2 Source

Water Booster

BIB BIB

BIB BIB BIB

BIB BIB

BIB BIB

BIBBIB

BIB BIB

BIB BIB BIB

BIB BIB BIB

Water Water SourceSource

Water Regulator


11

DRINK OPTIONS

16 Possible Brand Syrup flavors from 4 nozzles

16 Possible Soda drinks

8 Possible Plain Water drinks (with programming).

12 Possible Injected Syrup flavors or waters• 3 Injected Flavors for each nozzle• Buttons programmable to activate water or soda dispense.

• Plain water programmable on nozzles #2 and #3 only

• 4 brand valves

1234

, 3 brand valves, or 2 brand valves

FS - 14 shown above

VALVE OPTIONS

FS30-16 = 4

FS30-15 = 3 + 1

FS30-14 = 2 + 1 + 1

FS30-13= 2 + 1 + 1

FS30-12 FS30-11 FS30-10 FS30-9

PUSH

ICEICEPush LeverPush Lever

PUSH


PUSH


PUSH


FS30-8

ICEICEICEICEICEICEICEICEICEICEPUSH\PUSH\PUSH\PUSH\PUSH\

CONFIGURATION OPTIONS

S1-3S1-1

S1-2

IS1-1`

S2-1

S2-2

S2-3

S2-4

S3-1

S3-2

S3-3

S3-4

S4-1 S4-3

S4-4

1234

IS1-2

IS1-3

IS2-1

IS2-2

IS2-3

IS3-1 IS4-1

IS4-2

IS4-3

1234

S=Brand Syrups IS= Injected Flavors Nozzle Number - Button Position


PUSH

IS3-2

IS3-3

Note: Brands covering 2 positions take top designator

S1-4S4-2

VALVE PANEL LAYOUT

Ring 1 Ring 1

(Inner most)

Ring 2

Ring 3

Ring 1 - Category 2 & 3 drinks

Ring 2 - All category drinks

Ring 3 – Category 1, 2 & 4 drinks

Ring 4 - Category 1, 2 & 4 drinks

Drink Categories#1 Bright Colors (Red Flash, Big Red, Orange, Fruit Punch)

#2 Thin Dark Colors (Diet Cola, Diet Dr. Pepper, Teas)

#3 Light Colors (Lemonade, Lemon Lime, Sprite, 7-Up)

#4 Dark Colors (Cola, Root Beer, Dr. Pepper)

Ring 4(Outer most)

Ring 2

Ring 3

Ring 4

PANEL LAYOUT ALIGNMENT RECOMMENDATIONS

BRAND LEGEND

S2 - 2 Equals Syrup to Nozzle 2, Position 2S3 - 3 Equals Syrup to Nozzle 3, Position 3

S1 - 1S2- 2S3 - 3

1234


PUSH

S1 - 1 Equals Syrup to Nozzle 1, Position 1

IS2 - 1IS3 - 2

1234


PUSH

INJECTED FLAVOR LEGEND

IS4-3 Equals Injected Syrup, Nozzle 4, Position 3

IS4 - 3



SODA Inbound Water to carbonator for soda

or Water

Soda

4 3 2 1

Soda Soda Sodaor

Water

SODA AND WATER LEGEND

WATER Inbound Water for non-carbonated drinks

INLET CONNECTIONS

Water Inlets

Inlet Connections

Injected Flavors

Brand Syrup and CO2

WATER FOR SODA

WATER

Brand Syrup Inlets

Water Inlets

Injected SyrupFlavor Inlets

S1-1

S1-2

12

S1-3

S1-4


IS1-1

IS1-2

IS1-3

S2-2

S2-1 S2-3

S2-4

IS2-1

IS2-2

IS2-3

IS3-1

IS3-2

IS3-3

S4-1

S4-2

S4-3

S4-4

4 3

IS4-1

IS4-2

IS4-3

IS1-1

IS1-2

IS1-3

IS2-1

IS2-2

IS2-3

IS3-1

IS3-2

IS3-3

IS4-1

IS4-2

IS4-3

S 1-1

S 1-3

S 1-2

S 1-4

S 2-1

S 2-3

S 2-2

S 2-4

S 3-1

S 3-3

S 3-2

S 3-4

S 4-1

S 4-3

S 4-2

S 4-4

PUSH

S3-4

S3-3

S3-2

S3-1

CO2

Inlet

SYRUP/WATER/CO2 INLET DIAGRAM

BRAND INLET CONNECTIONS

• 16 Brand Syrup Inlets Brand Syrup Inlet Connections

• 3/8” hose Inlet Fittings

BRAND SYRUP INLETS\

Brand Syrup Inlets

IS1-1

IS1-2

IS1-3

IS2-1

IS2-2

IS2-3

IS3-1

IS3-2

IS3-3

IS4-1

IS4-2

IS4-3

S 1-3

S 1-2

S 1-4

S 2-1

S 2-3

S 2-2

S 2-4

S 3-1

S 3-3

S 3-2

S 3-4

S 4-1

S 4-3

S 4-2

S 4-4

CO2 Inlet

S 1-1

Injected Flavor Inlets

Water Inlets

WA

TE

R

FO

R S

OD

A

PL

AIN

W

AT

ER

Connect to Bundle Tubing

3/8” line

Hook-up Fittings16- 3/8 barb unions

INLET CONNECTIONS (BRANDS)

INJECTED SYRUP FLAVOR CONNECTIONS

1/4” hose connections

12 Inlet connections for Injected Flavors• 1/4” hose connections

Note: Injected Flavors Do Not pass through Cold Plate.

Flavors dispense at ambient temperature.

To assure splash plate will latch, turn clamps to side after crimping

\

S 1-3

S 1-2

S 1-4

S 2-1

S 2-3

S 2-2

S 2-4

S 3-1

S 3-3

S 3-2

S 3-4

S 4-1

S 4-3

S 4-2

S 4-4

CO2 Inlet

S 1-1

Water Inlets

WA

TE

R

FO

R S

OD

A

PL

AIN

W

AT

ER

INJECTED SYRUP FLAVOR INLETS

IS1-1

IS1-2

IS1-3

IS2-1

IS2-2

IS2-3

IS3-1

IS3-2

IS3-3

IS4-1

IS4-2

IS4-3


Brand Syrup Inlets

x 3

Note: Harness must be made behind or under unit to accommodate installation of splash plate. Configuration above for illustration purpose only

Flavor Harness options

INLET CONNECTIONS (FLAVORS & BRANDS)

Kit Pt. #82-3476

INJECTED SYRUP FLAVOR HARNESS CONNECTIONS

IS1-1

IS1-2

IS1-3

IS2-1

IS2-2

IS2-3

IS3-1

IS3-2

IS3-3IS4-3

IS4-2

IS4-1

Typical 3 Injected Syrup Flavor harness configuration

WATER INLETS CONNECTIONS

Inlet Water Connections• Water to dispenser (3/8” hose)

• Water to carbonator (3/8” hose)

Bottom Left Front

Note: Water regulator required for water to carbonator above 50 psi.

Note: Water booster required if static pressure is below 70 psi

\

WATER FOR SODA

PLAIN WATER

IS1-1

IS1-2

IS1-3

IS2-1

IS2-2

IS2-3

IS3-1

IS3-2

IS3-3

IS4-1

IS4-2

IS4-3


WATER INLETS

Brand Syrup InletsWater Inlets CO2 Inlet

S 1-1

S 1-3

S 1-2

S 1-4

S 2-1

S 2-3

S 2-2

S 2-4

S 3-1

S 3-3

S 3-2

S 3-4

S 4-1

S 4-3

S 4-2

S 4-4

(x 3)

INLET CONNECTIONS (WATER, FLAVORS & BRANDS)

Install water regulator (included with unit) in line to carbonator pump inlet. Confirm flow direction before installing

WATER INLET CONNECTIONS

Important

• The unit must be level to assure proper carbonation levels•A Water Boosting System is required for the

Plain Water drinks if incoming water pressure

is less than 70 PSI static.

• A Water Regulator is required for water to

carbonator if pressure is more than 50psi.

• A water filtration system is recommended.

CO2 INLETS CONNECTIONS

CO2 Inlet Connections• 1 (1/4” male flare) fitting or 3/8” barb on newer units• Regulator Setting 75 psi • Install 3/8” hose x ¼” nut adapter fitting (included with older unit)

Note: CO2 pressure must be a of 25 psi above incoming water pressure

CO2 INLET CONNECTION\

Brand Syrup InletsWater Inlets

COCO2 2 InletInlet

S 1-1

S 1-3

S 1-2

S 1-4

S 2-1

S 2-3

S 2-2

S 2-4

S 3-1

S 3-3

S 3-2

S 3-4

S 4-1

S 4-3

S 4-2

S 4-4

WA

TE

R

FO

R S

OD

A

PL

AIN

W

AT

ER

IS1-1

IS1-2

IS1-3

IS2-1

IS2-2

IS2-3

IS3-1

IS3-2

IS3-3

IS4-1

IS4-2

IS4-3

27

DRAINS

• Single drain connection (drip tray)

• 3/4” Straight connection

• Ice bin drains into drip tray

• Drain tube elbow fitting

• Insulating drain line is required

FS 30 SETUP

ENTER:

UPDOWN

LEFT

RIGHT

CANCEL

Moves cursor to right within menu

Exit menu without saving changes

Moves cursor to left within menu

Menu up navigation and increases value changes

Menu down navigation and decreases value changes

Press to enter sub-menu and save changes

LCD screen split into upper and lower sections

Programming Buttons

V: 1 L: 2 R: 1

ENTERCANCEL

FS PROGRAMING

FS-30 SETUP MAJOR / MINOR

FS-30 SETUP CONFIG BONUS KEY

FS-30 SETUP SODA / PLAIN WATER

BRANDS PER SIDE V:1 L:2 R:1

BONUS KEY SETUP V: 1 T:F M:S B:W

CARB / WATER SET UP V:2 1:S 2:W: 3:S 4:W ENTERCANCEL

scrolls through Main Menu Press “Enter” to enter sub-category Moves cursor to right or left

Changes value (number/letter)

Press “Enter” to save changes Press “Cancel” to exit menus

Main Menu Sub-category

LANCER FS-30 VER. 0.40000 Initialization Screen

(Boot up only)

2nd Sub-category

SET PC MODE OFF ON

ON TIME (MSEC) 04000

FS-30 SETUP PC MODE

FS-30 SETUP PC TIME

FS-30 SETUP CFG DISPENSE DLY

DISPENSE DELAY V1 B1 DLY1

SET DELAY (MS) 00075

FS-30 SETUP ICE STIR OFF

OFF TIME (MIN) 00060

FS-30 SETUP ICE STIR ON

ON TIME (MSEC) 02000

MAIN MENU LAYOUT

MAJOR / MINORFS 30 SETUPBRANDS PER

SIDEV: 1 L: 2 R: 1

MAJOR/MINOR - Menu to select valve layout

1234

L R L R L R L R

1 2 2 2 2 2 2 1

BRANDS PER SIDE - Number of brands on left and right side of specified valve

Valve #: 1 Left side: 2 brands Right side: 1 brand

ENTERCANCEL

MAJOR/MINOR MENU

CONFIG BONUS

KEY

FS 30 SETUP

CONFIG BONUS KEY - Menu to program injected flavor buttons to dispense flavor syrup, water or soda. BONUS KEY SETUP - Designate valve number, then select F (Flavor), W (Water) or S (Soda) for Top, Middle and Bottom button positions.

1234

TopMiddleBottom

Valve # : 3 Top: Flavor Middle: Soda Bottom: Water

BONUS KEY SETUPV: 3 T: F M:S B: W

ENTERCANCEL

CONFIG BONUS KEY

SODA/PLAIN WATER

FS 30 SETUPCARB/WATER SETUPV: 2 1:S 2:W 3:S 4:W

134

1

2

3

4

SODA/PLAIN WATER - Menu to program valve brands as soda or water drinksCARB/WATER SETUP - Designate valve number (2 and 3 only), then select W (Water) or S (Soda) for brand positions 1 through 4. Valves #1 and #4 are soda only.

ENTERCANCEL

2

SODA/PLAIN WATER

ICE STIR OFFFS 30 SET UPOFF TIME (min)

00060

ICE STIR OFF - Menu allows for selection of periodic ice agitator stir interval

OFF TIME (mins) - Designate number of minutes between stir cycles.

The recommended time is 60 min for cubed ice

and 150 min for cubelet ice.

in minutes.

ENTERCANCEL

ICE STIR OFF

ICE STIR ONFS 30 SETUPON TIME (msec)

02000

ICE STIR ON - Menu sets duration of periodic ice agitator stir interval.

ON TIME (msec) - Designate duration of stir cycle in milliseconds.

The recommended time is 2 seconds (or 2000 msec) for cubed ice and 4 seconds for cubelet ice.

ENTERCANCEL

ICE STIR ON

35

BRIXING AND RATIO

Ratio Cup

Separator

• Set water flow rate first with ratio cup at 15 ounces in 4 seconds.

• Set syrup ratio with separator (included with unit) and ratio cup

• Set injected syrup with ratio cup

36

WATER, BRAND AND FLAVOR MODULES

Modules are a combination solenoid and flow control.

Injected Flavor modules are white, Syrups areblack and Water (Soda or Plain) are gray.

Injected Flavor Brand Syrup Water

37

SETTING WATER FLOW RATE

Flow Rate (3.75 oz./sec.) x 4 seconds = 15.00 oz.

closed

open

Valve Block

• Shut off syrup (brand) supply to nozzle by closing shut-off at back block, disconnecting coil wire at plug connection or disconnecting BIB connector.• Dispense water into the brix cup for 4 seconds• Adjust to 15oz. of water in 4 seconds if needed

38

ADJUSTING MODULE FLOW CONTROLS

Counter clockwise will decrease flow rate of water or syrup module. This occurs by placing less tension on spring which allows piston to move forward thus blocking more of sleeve ports and decreases flow.

Clockwise will increase flow rate of water, soda or syrup module. This occurs by placing more tension on internal spring, which pushes piston backwards thus uncovering sleeve ports and increases flow.

39

INCREASE FLOW ADJUSTMENT

Adjustment screw clockwise to increase flow rate

Sleeve

Sleeve

Flow Direction

Piston

Piston

40

SETTING WATER FLOW RATE

Flow Rate (3.75 oz./sec.) x 4 seconds = 15.00 oz.

closed

open

Valve Block

• Shut off syrup (brand) supply to nozzle by closing shut-off at back block, disconnecting coil wire at plug connection or disconnecting BIB connector.• Dispense water into the brix cup for 4 seconds• Adjust to 15oz. of water in 4 seconds if needed

41Water/SodaSyrup

SETTING BRAND SYRUPS

• Remove valve nozzle and install syrup separator

• Adjust syrup flow rate (at module) so that water and syrup levels rise together in ratio cup. Adjust syrup module “in” (clockwise) to increase the flow or “out” (counter-clockwise) to decrease the flow.

42

SETTING INJECTED FLAVOR

closed

open

Valve Block

•Shut off water (soda) and brand syrup at valve block•Place ratio cup under nozzle•Activate bonus, then brand button at valve for 12 seconds. •Adjust injected syrup flow to equal 2 oz. in 12 seconds

INSTALLATION CHECKLIST

1. Assure a dedicated 115 VAC, 15 amp electrical circuit is provided for the unit.

2. Assure counter will support 680 lb unit plus ice machine (if applicable).

3. Cut counter for line access (if necessary), then set unit in place.

4. Run lines between unit and water, C02 and syrup supply. Use 3/8” I.D. tubing

for syrup, CO2 and water line runs up to 100 feet. For line runs over 100 foot,

1/2” tubing is recommended.

5. Install water booster (Lancer p/n 82-3401 or MC-163172) between water

supply and unit. Tee off outbound boosted water line, run a line to plain water

inlet and one to Carbonator pump inlet.

6. Splice water regulator (50 psi) in line between water booster and pump inlet.

7. Run drain tubing under unit and to drain but do not connect to drip tray.

8. Connect CO2 line to unit CO2 inlet.

9. Connect brand syrup lines to syrup inlet fittings. It may be necessary to use

braided tubing “pigtails” between inlets and bundle tubing.

10. Assure water based brand syrups (if used) are plumbed to valves 2 &3 only.

11. Prepare Bonus Flavor harness and connect to bonus flavor inlets. Then connect harness to bonus lines from syrup source.

12. Install drain on drip tray and latch tray in place. Insure drain lines are at least 1” ID. Place enough ice in bin to fill approximately 1/3 full.

13. To start-up unit, assure carbonator motor is unplugged from power supply, then turn on water to unit. Power-up unit.

14. Bleed air out of carbonator tank through the relief valve and dispensing valves.

15. Turn on CO2 and set regulator pressures to 75 psi. Gas out carbonator tank.

16. Power unit down. Plug Carbonator Motor into power board. Power unit up again. Dispense soda from all four valves to assure good flow at each valve.

17. Set soda (and water) flow rates to 15 oz in 4 seconds.

18. Connect syrup connectors to syrup containers.

19. Insure ice is on the cold plate before ratioing.

20. Ratio drinks using correct sugar/diet sides of ratio cup.

21. Set injected flavor syrup flow rate to 2 oz in 12 seconds.

Note: It may be necessary to raise CO2 pressure on syrup pump(s) slightly higher for thicker syrups to

achieve proper brix ratio. However, DO NOT EXCEED PUMP MANUFACTURES RECOMMENDED

MAXIUM PRESSURE!!

INSTALLATION CHECKLIST

PROGRAMMING SETUP REVIEW

• Confirm Major/Minor Brand valve setup.• Configure Bonus Key setup.• Configure Soda/Plain Water to brands.• Confirm Ice Stir Off/On times• If Pure Link/ R.O. water system, is used,

raise Probe Threshold in increments of 50 as needed up to a maximum of 1000. Because RO water has less impurities, threshold setting may need to be more sensitive to recognize Carbonator on/off levels.

46

COUNTER TEMPLATE

30.3

23.018.623

7.3

1.6733.0

30.0

28.138

6.0

3.0

1.5

15.0

26.0 2.02.0

Note: This

Drawing is not

to actual size

47

Brand/Flavor Brand/Flavor1 2 Coca-Cola 1 7-Up1 2 Diet Coke 1 1 Mug Root Beer1 2 Sprite 1 Powerade Mountain Blast1 1 Minute Maid Lemonade 1 Tropicana Lemon

1 Nestea Unsweetened 1 Wild Cherry Pepsi1 Diet Sprite Zero 1 Cherry Coke

1 1 Barq's Root Beer 1 Nestea Raspberry1 Caffeine Free Diet Coke 1 Hawaiian Punch1 Mr. Pibb Extra 1 Hi-C Friut Punch

1 2 Pepsi-Cola 4 Cherry Flavoring1 2 Diet Pepsi 4 Vanilla Flavoring1 1 Mt. Dew 4 Lemon Flavoring

1 Mt. Dew Code Red 4 Lime Flavoring1 2 Dr. Pepper 2 Water (Flavor button)

1 Diet Dr. Pepper 2 Soda (Flavor button)1 Gatorade Lemon Lime 1 Countrytime Lemonade

1 Fanta Orange 1 Brisk Raspberry Tea 1 Vault 1 Coke Zero

Standard FS Label Kit - Part Number 82-3878

Quantity QuantityM

ajo

r

Maj

or

Min

or

Current as of August 11, 2008

Min

or

GENERIC LABEL KIT

48

Major Minor Description Major Minor Description06-2703 06-2704 FS30,MBRAND,DIE 06-2703-27 06-2704-27 FS30,MBRAND,7UP 06-2703-00 06-2704-00 FS30,MBRAND,CC 06-2703-28 06-2704-28 FS30,MBRAND,RED FUSION 06-2703-01 06-2704-01 FS30,MBRAND,DIET COKE 06-2703-29 06-2704-29 FS30,MBRAND,WELCH'S 06-2703-02 06-2704-02 FS30,MBRAND,SPRITE 06-2703-30 06-2704-30 FS30,MBRAND,IBC RT BEER 06-2703-02/01 06-2704-02/01 FS30,MBRAND,SPRITE 06-2703-31 06-2704-31 FS30,MBRAND,SKIST CH LIMEA06-2703-03 06-2704-03 FS30,MBRAND,BARQS RB 06-2703-32 06-2704-32 FS30,MBRAND,SKIST ORG 06-2703-04 06-2704-04 FS30,MBRAND,CC CAF FREE 06-2703-33 06-2704-33 FS30,MBRAND,STWBRU CRUSH 06-2703-05 06-2704-05 FS30,MBRAND,MM LEMONADE 06-2703-34 06-2704-34 FS30,MBRAND,AW RT BEER 06-2703-05/01 06-2704-05/01 FS30,MBRAND,MM LEMONADE 06-2703-35 06-2704-35 FS30,MBRAND,HIRES RT BR 06-2703-06 06-2704-06 FS16,MBRAND,POWERADE LL 06-2703-36 06-2704-36 FS30,MBRAND,HWN PUNCH 06-2703-06/01 06-2704-06/01 FS30,MBRAND,POWERADE LL 06-2703-37 06-2704-37 FS30,MBRAND,VERNORS 06-2703-07 06-2704-07 FS16,MBRAND,NTEA UNSWEET 06-2703-38 06-2704-38 FS30,MBRAND,SQUIRT 06-2703-08 06-2704-08 FS16,MBRAND,FANTA ORG 06-2703-39 06-2704-39 FS30,MBRAND,DIET SQUIRT 06-2703-08/01 06-2704-08/01 FS30,MBRAND,FANTA ORG 06-2703-40 06-2704-40 FS30,MBRAND,GATOR FRUIT PU06-2703-09 06-2704-09 FS30,MBRAND,PEPSI-COLA 06-2703-41 06-2704-41 FS30,MBRAND,LLP SWTN 06-2703-09/01 06-2704-09/01 FS30,MBRAND,PEPSI-COLA 06-2703-42 06-2704-42 FS30,MBRAND,CTRYTIME LEMON06-2703-10 06-2704-10 FS30,MBRAND,MT DEW 06-2703-43 06-2704-43 FS30,MBRAND,PUREWATER 06-2703-10/01 06-2704-10/01 FS30,MBRAND,MT DEW 06-2703-44 06-2704-44 FS30,MBRAND,MR PIBB EXTRA 06-2703-11 06-2704-11 FS30,MBRAND,DIET PEPSI 06-2703-45 06-2704-45 FS30,MBRAND,MM STRAWBERRY 06-2703-12 06-2704-12 FS30,MBRAND,CRED MT DEW 06-2703-46 06-2704-46 FS30,MBRAND,RED FLASH 06-2703-13 06-2704-13 FS30,MBRAND,GATORADE LL 06-2703-47 06-2704-47 FS30,MBRAND,NESTEA RASP 06-2703-14 06-2704-14 FS30,MBRAND,DR PEPPER 06-2703-48 06-2704-48 FS30,MBRAND,SIERRA MIST 06-2703-15 06-2704-15 FS30,MBRAND,DIET DR PEP 06-2703-49 06-2704-49 FS30,MBRAND,FRUIT WORKS 06-2703-16 06-2704-16 FS30,MBRAND,D CK CAF FREE 06-2703-50 06-2704-50 FS30,MBRAND,LIP BRISK SWT 06-2703-17 06-2704-17 FS30,MBRAND,POWERADE FP 06-2703-50/01 06-2704-50/01 FS30,MBRAND,LIP BRISK SWT 06-2703-18 06-2704-18 FS30,MBRAND,CHERRY COKE 06-2703-51 06-2704-51 FS30,MBRAND,LIP BRISK UNSW06-2703-18/01 06-2704-18/01 FS30,MBRAND,CHERRY COKE 06-2703-51/01 06-2704-51/01 FS30,MBRAND,LIP BRISK UNSW06-2703-19 06-2704-19 FS30,MBRAND,MM ORANGE 06-2703-52 06-2704-52 FS30,MBRAND,LIP BRK SWT LM06-2703-20 06-2704-20 FS30,MBRAND,HIC FP 06-2703-53 06-2704-53 FS30,MBRAND,LIP BRK LMN 06-2703-20/01 06-2704-20/01 FS30,MBRAND,HIC FP 06-2703-53/01 06-2704-53/01 FS30,MBRAND,LIP BRK LMN 06-2703-21 06-2704-21 FS30,MBRAND,SURGE 06-2703-54 06-2704-54 FS30,MBRAND,MUG ROOT BEER 06-2703-22 06-2704-22 FS30,MBRAND,NTEA SWEET 06-2703-54/01 06-2704-54/01 FS30,MBRAND,MUG ROOT BEER 06-2703-23 06-2704-23 FS30,MBRAND,HIC PKLEMON 06-2703-55 06-2704-55 FS30,MBRAND,GATORADE ORG 06-2703-24 06-2704-24 FS30,MBRAND,DIET MT DEW 06-2703-56 06-2704-56 FS30,MBRAND,FANTA STRW 06-2703-24/01 06-2704-24/01 FS30,MBRAND,DIET MT DEW 06-2703-56/01 06-2704-56/01 FS30,MBRAND,FANTA STRW 06-2703-25 06-2704-25 FS30,MBRAND,LIP BRSK RASP 06-2703-57 06-2704-57 FS30,MBRAND,DIET SPRITE 06-2703-25/01 06-2704-25/01 FS30,MBRAND,LIP BRSK RASP 06-2703-58 06-2704-58 FS30,MBRAND,WLDSTAL 06-2703-26 06-2704-26 FS30,MBRAND,DIET 7UP 06-2703-58/01 06-2704-58/01 FS30,MBRAND,WLDSTAL

FS Brand and Bonus Flavor Labels

LABEL PART NUMBERSPage 1

49

Major Minor Description Major Minor Description06-2703 06-2704 FS30,MBRAND,DIE 06-2703-27 06-2704-27 FS30,MBRAND,7UP 06-2703-00 06-2704-00 FS30,MBRAND,CC 06-2703-28 06-2704-28 FS30,MBRAND,RED FUSION 06-2703-01 06-2704-01 FS30,MBRAND,DIET COKE 06-2703-29 06-2704-29 FS30,MBRAND,WELCH'S 06-2703-02 06-2704-02 FS30,MBRAND,SPRITE 06-2703-30 06-2704-30 FS30,MBRAND,IBC RT BEER 06-2703-02/01 06-2704-02/01 FS30,MBRAND,SPRITE 06-2703-31 06-2704-31 FS30,MBRAND,SKIST CH LIMEA06-2703-03 06-2704-03 FS30,MBRAND,BARQS RB 06-2703-32 06-2704-32 FS30,MBRAND,SKIST ORG 06-2703-04 06-2704-04 FS30,MBRAND,CC CAF FREE 06-2703-33 06-2704-33 FS30,MBRAND,STWBRU CRUSH 06-2703-05 06-2704-05 FS30,MBRAND,MM LEMONADE 06-2703-34 06-2704-34 FS30,MBRAND,AW RT BEER 06-2703-05/01 06-2704-05/01 FS30,MBRAND,MM LEMONADE 06-2703-35 06-2704-35 FS30,MBRAND,HIRES RT BR 06-2703-06 06-2704-06 FS16,MBRAND,POWERADE LL 06-2703-36 06-2704-36 FS30,MBRAND,HWN PUNCH 06-2703-06/01 06-2704-06/01 FS30,MBRAND,POWERADE LL 06-2703-37 06-2704-37 FS30,MBRAND,VERNORS 06-2703-07 06-2704-07 FS16,MBRAND,NTEA UNSWEET 06-2703-38 06-2704-38 FS30,MBRAND,SQUIRT 06-2703-08 06-2704-08 FS16,MBRAND,FANTA ORG 06-2703-39 06-2704-39 FS30,MBRAND,DIET SQUIRT 06-2703-08/01 06-2704-08/01 FS30,MBRAND,FANTA ORG 06-2703-40 06-2704-40 FS30,MBRAND,GATOR FRUIT PU06-2703-09 06-2704-09 FS30,MBRAND,PEPSI-COLA 06-2703-41 06-2704-41 FS30,MBRAND,LLP SWTN 06-2703-09/01 06-2704-09/01 FS30,MBRAND,PEPSI-COLA 06-2703-42 06-2704-42 FS30,MBRAND,CTRYTIME LEMON06-2703-10 06-2704-10 FS30,MBRAND,MT DEW 06-2703-43 06-2704-43 FS30,MBRAND,PUREWATER 06-2703-10/01 06-2704-10/01 FS30,MBRAND,MT DEW 06-2703-44 06-2704-44 FS30,MBRAND,MR PIBB EXTRA 06-2703-11 06-2704-11 FS30,MBRAND,DIET PEPSI 06-2703-45 06-2704-45 FS30,MBRAND,MM STRAWBERRY 06-2703-12 06-2704-12 FS30,MBRAND,CRED MT DEW 06-2703-46 06-2704-46 FS30,MBRAND,RED FLASH 06-2703-13 06-2704-13 FS30,MBRAND,GATORADE LL 06-2703-47 06-2704-47 FS30,MBRAND,NESTEA RASP 06-2703-14 06-2704-14 FS30,MBRAND,DR PEPPER 06-2703-48 06-2704-48 FS30,MBRAND,SIERRA MIST 06-2703-15 06-2704-15 FS30,MBRAND,DIET DR PEP 06-2703-49 06-2704-49 FS30,MBRAND,FRUIT WORKS 06-2703-16 06-2704-16 FS30,MBRAND,D CK CAF FREE 06-2703-50 06-2704-50 FS30,MBRAND,LIP BRISK SWT 06-2703-17 06-2704-17 FS30,MBRAND,POWERADE FP 06-2703-50/01 06-2704-50/01 FS30,MBRAND,LIP BRISK SWT 06-2703-18 06-2704-18 FS30,MBRAND,CHERRY COKE 06-2703-51 06-2704-51 FS30,MBRAND,LIP BRISK UNSW06-2703-18/01 06-2704-18/01 FS30,MBRAND,CHERRY COKE 06-2703-51/01 06-2704-51/01 FS30,MBRAND,LIP BRISK UNSW06-2703-19 06-2704-19 FS30,MBRAND,MM ORANGE 06-2703-52 06-2704-52 FS30,MBRAND,LIP BRK SWT LM06-2703-20 06-2704-20 FS30,MBRAND,HIC FP 06-2703-53 06-2704-53 FS30,MBRAND,LIP BRK LMN 06-2703-20/01 06-2704-20/01 FS30,MBRAND,HIC FP 06-2703-53/01 06-2704-53/01 FS30,MBRAND,LIP BRK LMN 06-2703-21 06-2704-21 FS30,MBRAND,SURGE 06-2703-54 06-2704-54 FS30,MBRAND,MUG ROOT BEER 06-2703-22 06-2704-22 FS30,MBRAND,NTEA SWEET 06-2703-54/01 06-2704-54/01 FS30,MBRAND,MUG ROOT BEER 06-2703-23 06-2704-23 FS30,MBRAND,HIC PKLEMON 06-2703-55 06-2704-55 FS30,MBRAND,GATORADE ORG 06-2703-24 06-2704-24 FS30,MBRAND,DIET MT DEW 06-2703-56 06-2704-56 FS30,MBRAND,FANTA STRW 06-2703-24/01 06-2704-24/01 FS30,MBRAND,DIET MT DEW 06-2703-56/01 06-2704-56/01 FS30,MBRAND,FANTA STRW 06-2703-25 06-2704-25 FS30,MBRAND,LIP BRSK RASP 06-2703-57 06-2704-57 FS30,MBRAND,DIET SPRITE 06-2703-25/01 06-2704-25/01 FS30,MBRAND,LIP BRSK RASP 06-2703-58 06-2704-58 FS30,MBRAND,WLDSTAL 06-2703-26 06-2704-26 FS30,MBRAND,DIET 7UP 06-2703-58/01 06-2704-58/01 FS30,MBRAND,WLDSTAL

FS Brand and Bonus Flavor Labels

LABEL PART NUMBERSPage 1

Return to Main Menu

FS30 InstallationFS30 Installation

Documents

FS30 Installation