Fts Esprimopoperatingmanualen 10 1079143

8/9/2019 Fts Esprimopoperatingmanualen 10 1079143

1/68

Professional PC

Operating Manual

English

ESPRIMO P


2/68

Are there ...

... any technical problems or other questions which you would like to be clarified?

Please contact:

● our Hotline/Help Desk(see the included Help Desk list or go to: http://www.fujitsu-siemens.com/support/helpdesk.html)

● your sales partner

● your sales outlet

Further information can be found in the "Safety" and "Warranty" manuals.

The latest information on our products, tips, updates, etc., can be found on the internet under:http://www.fujitsu-siemens.com


3/68


4/68

This manual was produced by

cognitas. Gesellschaft für Technik-Dokumentation mbH – www.cognitas.de

Published by

Fujitsu Siemens Computers GmbH

Printed in the Federal Republic of Germany

AG 0405 04/05

Edition 1

Order No.: A26361-K1008-Z120-1-7619

A26361-K1008-Z120-1-7619


5/68

ESPRIMO P

Operating Manual

Introduction

Important notes

Preparation for use andoperation

Troubleshooting and tips

System expansions

Technical data

Index

April 2005 edition


6/68

ESPRIMO is a registered trademark of Fujitsu Siemens Computers GmbH.

Microsoft, MS, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft

Corporation.

VESA and DPMS are trademarks of Video Electronics Standards Association.

PS/2 is a registered trademark of International Business Machines, Inc.

Pentium is a registered trademark of Intel Corporation, USA.

All other trademarks referenced are trademarks or registered trademarks of their respective

owners, whose protected rights are acknowledged.

Copyright © Fujitsu Siemens Computers GmbH 2004

All rights, including rights of translation, reproduction by printing, copying or similar methods,

in part or in whole, are reserved.

Offenders will be liable for damages.

All rights, including rights created by patent grant or registration of a utility model or design,

are reserved.

Delivery subject to availability. Right of technical modification reserved.


7/68

Contents Your ESPRIMO P ... ............................................................................................................................ 1 Notational conventions ......................................................................................................................... 2

Important notes .................................................................................................................................. 3

Safety notes.......................................................................................................................................... 3

Transporting the device ........................................................................................................................ 3

Cleaning the device .............................................................................................................................. 3

Energy saving, disposal and recycling ................................................................................................. 4 CE marking........................................................................................................................................... 4 FCC Class B Compliance Statement ................................................................................................... 5

Preparing for use................................................................................................................................ 7 Unpacking and checking the delivery................................................................................................... 7 Steps for initial setup ............................................................................................................................ 7 Setting up the device............................................................................................................................ 8

Connect the monitor, mouse and keyboard.......................................................................................... 8

Connecting the monitor ................................................................................................................ 8

Connecting the mouse ................................................................................................................. 9 Connecting a keyboard............................................................................................................... 10

Connecting the device to the mains voltage....................................................................................... 10

Initial switch-on: Software will be installed.......................................................................................... 11

Switching on monitor and device................................................................................................ 12

Installing the software................................................................................................................. 12 Connecting external devices .............................................................................................................. 13

Ports provided by the device ...................................................................................................... 14 Connecting external devices to the parallel or serial port........................................................... 15

Connecting external devices to the USB ports........................................................................... 15

Operation........................................................................................................................................... 17

Switching the device on...................................................................................................................... 17

Switching off the device...................................................................................................................... 17

Indicators provided by the device ....................................................................................................... 18 Keyboard ............................................................................................................................................ 19

Important keys and key combinations ........................................................................................ 20 Working with floppy disks ................................................................................................................... 21

Settings in BIOS Setup....................................................................................................................... 22

Property and data protection .............................................................................................................. 22

Unlocking and locking casing (optional) ..................................................................................... 22 Anti-theft protection and lead-sealing......................................................................................... 23

BIOS setup security functions .................................................................................................... 23 Access authorisation via SmartCard (optional) .......................................................................... 24

Troubleshooting and tips................................................................................................................. 25 Installing new software ....................................................................................................................... 25

Power-on indicator remains unlit after you have switched on your device......................................... 25

The device cannot be switched off with the ON/OFF switch .............................................................. 26

The screen stays blank....................................................................................................................... 26 No mouse pointer displayed on the screen ........................................................................................ 27 The floppy disk cannot be read or written........................................................................................... 28 Time and/or date is not correct........................................................................................................... 28

Error messages on the screen ........................................................................................................... 28

Restoring the hard disk contents ........................................................................................................ 28 Tips .................................................................................................................................................... 28

A26361-K1008-Z120-1-7619, edition 1


8/68

Contents

System expansions...........................................................................................................................29

Information about boards ............................................................................................................29 Opening the casing .............................................................................................................................30 Closing the casing...............................................................................................................................30

Installing casing lock ...........................................................................................................................30

Removing and installing the fan..........................................................................................................31

Remove the fan...........................................................................................................................31 Installing the fan..........................................................................................................................32

Installing and removing boards...........................................................................................................32 Installing a board.........................................................................................................................33

Removing a board.......................................................................................................................35

Low-Profile boards ......................................................................................................................36

Installing an additional serial port........................................................................................................38 Installing and removing drives ............................................................................................................39

Installing an accessible drive ......................................................................................................39

Removing an accessible drive ....................................................................................................40

Installing and removing the floppy disk drive ..............................................................................42

Installing and removing hard disk with EasyChange rails...........................................................43

Installing an removing USB interfaces ................................................................................................44

Installing front USB audio interfaces...........................................................................................45 Removing front USB audio interfaces.........................................................................................46

Installing USB interface at the rear side......................................................................................46

Installing/removing a SmartCard reader and/or WLAN module (optional)..........................................47 Installing SmartCard reader and/or WLAN module.....................................................................48 Removing SmartCard reader and/or WLAN module...................................................................50

Extensions to the mainboard...............................................................................................................51

Installing and removing the power supply...................................................................................51

Making changes on mainboard...................................................................................................53

Technical data ...................................................................................................................................55

Index...................................................................................................................................................57

A26361-K1008-Z120-1-7619


9/68

Your ESPRIMO P ...

... is available with various configuration levels with different hardware and software. You canincorporate operable drives (for example DVD drive) as well as other boards.

This manual tells you how to put your device into operation and how to operate it in daily use. Thismanual applies for all configuration levels. Depending on the configuration level chosen some of thehardware components described may not be available on your PC. Please observe the notes on youroperating system.

Depending on the configuration selected, the operating system is preinstalled on your hard disk (e.g.Microsoft Windows XP).

Your device has a number of security features to ensure that no unauthorised persons can accessyour data. You can lock your device mechanically. The security functions in the BIOS Setup also allowyou to protect your data by means of passwords. In addition, systems with a SmartCard reader offeradditional protection.

DeskUpdate allows you under some operating systems to easily and quickly install the latest driversand operating system extensions with a few mouse clicks. DeskUpdate is contained on the"Drivers & Utilities" CD.

Further information on this device is provided:

● in the "Safety" manual● in the "Ergonomics" manual● in the "Warranty" manual● in the operating manual for the monitor● in the manual for the mainboard● in the "BIOS Setup" manual● in your operating system documentation

● in the information files (e.g. *.PDF , *.HTML, *.DOC , *.CHM , *.TXT , *.HLP)

i

You will find an electronic version of some of the listed manuals on the "UserDocumentation" or "Drivers & Utilities" CD.

You can access and view the required information using the Acrobat Reader program,which is also on the CD. If necessary, you can also make a print version of the manual.

A26361-K1008-Z120-1-7619, edition 1 1


10/68

Your ESPRIMO P ...

Notational conventions

The following symbols are used in this manual:

! indicates information which is important for your health or for preventing

physical damage.

i

indicates important information which is required to use the system properly.

► Text which follows this symbol describes activities that must be performed inthe order shown.

This font indicates programme names, commands, or menu items.

"Quotation marks" indicate names of chapters, data carriers, and terms that are beingemphasised.

2 A26361-K1008-Z120-1-7619, edition 1


11/68

Important notes

In this chapter you will find information regarding safety which it is essential to take note of whenworking with your device.

Safety notes

!

Pay attention to the information provided in the "Safety" manual and in the followingsecurity notes.

During installation and before operating the device, please observe the instructions onenvironmental conditions in the "Technical data" chapter as well as the instructions in the"Preparing for use" chapter.

You may only operate the device, if the rated voltage for the device is set to the local

mains voltage. Check the rated voltage set for this device (see the "Preparing for use" chapter).

The ON/OFF switch does not disconnect the device from the mains voltage. To completelydisconnect the mains voltage, remove the power plug from the grounded mains outlet.

Replace the lithium battery on the mainboard in accordance with the instructions in the"Making changes on mainboard" - "Replacing lithium battery" chapter.

Caution, components in the system can get very hot.

Transporting the device

!

Transport all parts separately in their original packaging or in a packaging which protectsthem from knocks and jolts, to the new site. Do not unpack them until all transportationmanoeuvres are completed.

Cleaning the device

!

Turn off all power and equipment switches and remove the power plug from the mainssupply.

Do not clean any interior parts yourself, leave this job to a service technician.

Do not use any cleaning agents that contain abrasives or may corrode plastic.

Ensure that no liquid enters the system.

Wipe the casing with a dry cloth. If particularly dirty, use a cloth that has been moistened in milddomestic detergent and then carefully wrung out. Use disinfectant wipes to clean the keyboard andthe mouse.

A26361-K1008-Z120-1-7619, edition 1 3


12/68

Important notes

Energy saving, disposal and recycling

Further information can be found on the "User Documentation" or "Drivers & Utilities" CD providedwith your computer.

CE marking

CE marking for devices without radio component

The shipped version of this device complies with the requirements of the EECdirectives 89/336/EEC "Electromagnetic compatibility" and 73/23/EEC "Lowvoltage directive".

CE marking for devices with radio component

This equipment complies with the requirements of Directive 1999/5/EC of theEuropean Parliament and Commission from 9 March, 1999 governing Radio andTelecommunications Equipment and mutual recognition of conformity.

This equipment can be used in the following countries:

Belgium Denmark Germany EstoniaFinland France Greece UKIreland Iceland Italy LatviaLiechtenstein Lithuania Luxemburg MaltaNetherlands Norway Austria PolandPortugal Sweden Switzerland SlovakiaSlovenia Spain Czech Republic

Hungary Cyprus

Contact the corresponding government office of the respective country forcurrent information on possible operating restrictions. If your country is notincluded in the list, then please contact the corresponding supervisory authorityas to whether the use of this product is permitted in your country.

i

The Declarations of Conformity on this device are contained in the "Wireless LAN" manual,which is provided as a PDF file on one of the included CDs, e.g. "User Documentation", orcan be found on the Internet at http://manuals.fujitsu-siemens.com.

4 A26361-K1008-Z120-1-7619, edition 1


13/68

Important notes

FCC Class B Compliance Statement

The following statement applies to the products covered in this manual, unless otherwise specifiedherein. The statement for other products will appear in the accompanying documentation.

NOTE:This equipment has been tested and found to comply with the limits for a "Class B" digital device,pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian Interference-Causing Equipment Standard ICES-003 for digital apparatus. These limits are designed to providereasonable protection against harmful interference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energy and, if not installed and used in strictaccordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:

● Reorient or relocate the receiving antenna.● Increase the separation between equipment and the receiver.● Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.● Consult the dealer or an experienced radio/TV technician for help.

Fujitsu Siemens Computers GmbH is not responsible for any radio or television interference causedby unauthorised modifications of this equipment or the substitution or attachment of connectingcables and equipment other than those specified by Fujitsu Siemens Computers GmbH. Thecorrection of interferences caused by such unauthorised modification, substitution or attachment willbe the responsibility of the user.

The use of shielded I/O cables is required when connecting this equipment to any and all optionalperipheral or host devices. Failure to do so may violate FCC and ICES rules.

A26361-K1008-Z120-1-7619, edition 1 5


14/68


15/68

Preparing for use

!

Please take note of the safety information in the "Important notes" chapter.

Unpacking and checking the delivery

It is recommended not to throw away the original packaging material! It may be required forreshipment at some later date.

► Unpack all the individual parts.

► Check the delivery for damage incurred during transportation.

► Check whether the delivery agrees with the details in the delivery note.

Should you discover that the delivery does not correspond to the delivery note, notify your local salesoutlet immediately.

Steps for initial setup

Only a few steps are necessary to put your new device into operation for the first time:

● Select location for device and set up device

● Connect the monitor, mouse and keyboard

● Check the voltage at the mains outlet and connect the device to an electrical outlet

● Switching the device on

You will learn more about the individual steps in the following sections.

i

External devices

If you have received other devices in addition to your device (e.g. a printer or a modem),do not connect these until after the initial installation. The following sections contain adescription of how to connect these external devices.

Drives and boards

If you have received drives or boards with your device, please do not install them untilafter first-time setup. How to install drives and boards is described in the "Systemexpansions" chapter.

A26361-K1008-Z120-1-7619, edition 1 7


16/68

Setting up the device

!

When installing your device, give consideration to the safety notes in the "Safety" manual.

Set up the device only in its correct orientation (vertical position).

We recommend that you place your device on a surface with good anti-slip qualities. Inview of the multitude of different finishes and varnishes used on furniture, it is possible thatthe feet of the device will mark the surface they stand on.

Do not expose the device to extreme environmental conditions (see "Technical data").Protect the device from dust, humidity, and heat.

When installing the workstation, provide sufficient clearance around the device, asindicated in the "Technical data" chapter to ensure adequate ventilation. In order to avoidoverheating, do not cover the ventilation area of the monitor or the device.Do not stack several devices on top of each other.

Depending on the location of your device, bothersome vibrations and noises may occur.To prevent this, a distance of at least 3 mm should be maintained from other devices oncasing sides without ventilation surfaces. In addition, we recommend placing the device onsupport feet, as these buffer vibrations.

Connect the monitor, mouse and keyboard

The ports for the monitor, mouse, and keyboard are on the front and rear of the device.

Keyboard port, purple PS/2 mouse port, green

Monitor port, blue USB port, black

Connecting the monitor

► Follow the instructions contained in the monitor manual to prepare the monitor for operation(e.g. connecting cables).

► Plug the data cable into the monitor port of the device.

8 A26361-K1008-Z120-1-7619, edition 1


17/68

Preparing for use

On devices with monitor socket

12

2

► Depending on your device configuration level, plug the monitor power cable into either themonitor socket (optional) of the device (1) or a grounded power outlet (2).

i

When you connect the monitor to the monitor socket of the device, it automaticallyswitches off as soon as the device switches off.

!

The monitor power cable may only be connected to the monitor socket of the device if themonitor current consumption is smaller than 1.5 A with 230 V or 3 A with 115 V. Thevalues for the monitor current consumption can be found in the technical data on themonitor or in the operating manual for the monitor.

On devices without monitor socket

► Plug the power cable of the monitor into a grounded mains outlet (2).

Connecting the mouse

Depending on the equipment level selected, your device will be supplied with a PS/2 mouse or aUSB mouse.

Connecting a PS/2 mouse

► Connect the PS/2 mouse to the PS/2 mouse port of the device.

Connecting USB mouse

► Connect the USB mouse to the USB port of the device.

i

If you do not attach a mouse at the PS/2 mouse port, you can disable the mouse controllerin the BIOS Setup in order to free the IRQ12 for a different application.

A26361-K1008-Z120-1-7619, edition 1 9


18/68

Connecting a keyboard

Depending on the equipment level selected, your device will be supplied with a standard keyboard ora USB keyboard.

Connecting standard keyboardUse the supplied keyboard cable only.

► Plug the rectangular connector of the keyboard cable into the rectangular socket on theunderside or on the rear of the keyboard.

►

► Plug the round plug of the keyboard cable into the keyboard port on the device.

Connecting USB keyboard

Use the supplied keyboard cable only.

► Plug the rectangular connector of the keyboard cable into the socket on the underside or on therear of the keyboard.

►

► Insert the flat rectangular USB plug of the keyboard cable into a USB port of the device.

Connecting the device to the mains voltage

!

The visible value must agree with the local mains voltage:115 = 100 V to 127 V 230 = 200 V to 240 V

If an incorrect mains voltage is set, push the slide switch all the way into the other positionwith a pointed object.

You may only operate the device, if the voltage for the device is set to the local mainsvoltage.

100 V - 125 V

200 V - 240 V

► Check the voltage setting.

10 A26361-K1008-Z120-1-7619, edition 1


19/68


20/68

Switching on monitor and device

► Switch the monitor on (see the operating manual for the monitor).

► Switch the device on. To do this, follow the instructions below.

1

1 = ON/OFF switch

► Press the ON/OFF switch on the front of the device.

The power-on indicator lights green and the device is started.

Installing the software► During installation, follow the instructions on screen.

► Consult the operating system manual if there is anything unclear about the requested inputdata.

i

You will find further information about the system, drivers, utilities, and updates on the"Drivers & Utilities" CD supplied.

12 A26361-K1008-Z120-1-7619, edition 1


21/68

Preparing for use

Connecting external devices

!

Read the documentation on the external device before connecting it.

With the exception of USB devices, always remove all power plugs before connectingexternal devices!

Do not connect or disconnect cables during a thunderstorm.

Always take hold of the actual plug. Never unplug a cable by pulling the cable itself.

Connect and disconnect the cables in the order described below.

Connecting cables

► Turn off all power and equipment switches.

► Remove all power plugs from the grounded mains outlets.

► Plug all cables into the device and peripherals. You must observe the information provided inthe "Important notes" chapter.

► Plug all data communication cables into the utility sockets.

► Plug all power cables into the grounded mains outlets.

Disconnecting cables

► Turn off all power and equipment switches.

► Remove all power plugs from the grounded mains outlets.

► Unplug all data communication cables from the utility sockets.

► Unplug all cables from the device and peripherals.

i

USB devices are hot-pluggable. This means you can connect and disconnect deviceswhile your operating system is running.

Additional information can be found in the "Connecting external devices to the USB ports"section and in the documentation for the USB devices.

A26361-K1008-Z120-1-7619, edition 1 13


22/68

Ports provided by the device

The connections are located on the front and back of the device. The ports available on your devicedepend on the configuration level you have selected. The standard ports are marked with thesymbols shown below (or similar). Detailed information on the location of the connections is provided

in the manual for the mainboard.

Keyboard port, purple PS/2 mouse port, green

1

Serial port 1, teal or turquoise

2

Serial port 2, teal or turquoise

Monitor port, blue Parallel port/Printer, burgundy

Headphones port, orange or light

green

Microphone jack (mono), pink

Audio output (Line out), light green Audio input (Line in), light blue

Game port, gold SCSI connection

USB - Universal Serial Bus, black LAN

LAN port

i

Some of the connected devices require special drivers (see the documentation for theconnected device).

14 A26361-K1008-Z120-1-7619, edition 1


23/68

Preparing for use

Connecting external devices to the parallel or serial port

External devices can be connected to the parallel or serial port (e.g. a printer or a modem).

► Connect the data cable to the external device.

► Depending on the device, connect the data cable to the parallel port or the serial port .

For an exact description of how to connect external devices to the corresponding port, please seethe external device documentation.

i

Port settings

You can change the port settings (e.g. address, interrupt) in the BIOS Setup.

Device drivers

The devices connected to the parallel or serial port require drivers. Your operating systemalready includes many drivers. If the required drive is missing, install it. Current drivers areusually available on the Internet or will be supplied on a data carrier.

Connecting external devices to the USB ports

You can connect a wide range of external devices to the USB port (e.g. printer, scanner, modem orkeyboard).

i

USB devices are hot-pluggable. This means you can connect and disconnect deviceswhile your operating system is running.

Additional information can be found in the documentation for the USB devices.

► Connect the data cable to the external device.

► Connect the data cable to a USB port .

i

Device drivers

The devices you connect to the USB ports usually require no driver of their own, as therequired software is already included in the operating system. However, if the USB devicerequires its own software, please install it from the data carrier provided with the USBdevice.

A26361-K1008-Z120-1-7619, edition 1 15


24/68


25/68

Operation

Switching the device on

► If necessary, switch the monitor on (see the operating manual for the monitor).

► Press the ON/OFF switch on the front of the device.

The power-on indicator lights green and the device is started.

Switching off the device

► Shut down the operating system properly. For Windows: select Shut Down from the Start menu.

► If the operating system does not automatically switch the device into an energy-saving mode orswitch it off, press the ON/OFF switch.

The device then consumes a minimum amount of energy.

!

The ON/OFF switch does not disconnect the device from the mains voltage. To completelydisconnect the mains voltage, remove the power plug from the socket.

► If necessary, switch the monitor off (see the operating manual for the monitor).

A26361-K1008-Z120-1-7619, edition 1 17


26/68

Operation

Indicators provided by the device

The indicators are on the front of the casing. Which indicators are available on your device dependson the configuration level you have selected.

1 2

5

3

4

1 = Hard disk indicator

2 = Power-on indicator

3 = Drive indicator, e.g. DVD

4 = SmartCard reader indicator (optional)

5 = Floppy disk indicator

1 - Hard disk indicator

The indicator lights up when the hard disk of the device is accessed.

2 - Power-on indicator

– The indicator is green:The device is on.

i

The display can also light up green if the device has been switched off byholding the ON/OFF switch (see "Troubleshooting and tips").

– The indicator lights orange:The device is ready-to-operate or in energy-saving mode. After being switched on with

the power button, the device switches on or returns to the state it was in before theenergy-saving mode.

!

In the energy-saving mode the device may not be disconnected from the mainssupply, as this may otherwise result in data loss.

– The indicator does not light up:The device is disconnected from the power supply or is ready for operation. If your deviceis ready-to-operate it can be enabled with the ON/OFF switch.

18 A26361-K1008-Z120-1-7619, edition 1


27/68

Operation

3 - Drive indicator, e.g. DVD

The indicator lights up when the CD-ROM or DVD drive is accessed. You may only remove theCD/DVD when the indicator is dark.

4 - SmartCard reader indicator (optional)

The indicator lights up when the SmartCard reader is ready-to-use.The indicator flashes when the SmartCard is accessed.

5 - Floppy disk indicator

The indicator lights up when the floppy disk drive of the device is accessed. You may only removethe floppy disk when the indicator is unlit.

Keyboard

1

3 4 5

2

1 = Function keys

2 = Power button (optional)

3 = Alphanumeric keypad

4 = Cursor keys

5 = Numeric keypad (calculator keypad)

i

The illustrated keyboard is an example and may differ from the model you use.

A26361-K1008-Z120-1-7619, edition 1 19


28/68

Operation

Important keys and key combinations

The description of the following keys and key combinations applies to Microsoft operating systems.Details of other keys and key combinations can be found in the documentation of the relevantapplication programme.

ON/OFF switch (optional) Depending on the setting in the BIOS Setup, the system can be switched on, off, or onand off with this button. Some operating systems allow you to configure additionalfunctions of the ON/OFF switch in the Control Panel.

With some keyboards the ON/OFF switch can only be used with an ACPI (AdvancedConfiguration and Power Management Interface). Otherwise the key is inoperative.The mainboard must support this function.

Enter key confirms the marked selection. The enter key is also referred to as the "Return" key.

Start key calls up the Windows Start menu.

Menu key invokes the menu for the marked item (Windows).

Shift key enables upper-case letters and the upper key symbols to be used.

Alt Gr

Alt Gr (e.g. German keyboard) produces a character shown on the right-hand side of a key (e.g. the character @ onthe key Q ).

NumLock

Num Lock key by pressing the Num Lock key you switch between the Numeric keypad cursorcontrol functions and digit or comma functions.When the Num Lock indicator is lit the digit and comma keys are active.When the Num Lock indicator is not lit the cursor control functions are active in theNumeric keypad.

Ctrl

Ctrl keystarts key combination actions. The Ctrl key is also called "Control" or "Controlkey".

Ctrl Alt Del

Warm boot restarts your device. Press simultaneously the keys Ctrl , Alt+ Del . Under some operating systems the Task Managerappears first. Then you must press all three keys again to re-boot.

20 A26361-K1008-Z120-1-7619, edition 1


29/68

Operation

Working with floppy disks

i

Follow the instructions supplied by the vendor of the floppy disks.

Do not clean the floppy disk drive with cleaning floppy disks. Any attempt would destroythe read/write head in the disk drive within 20 seconds.

3

2

1

5

64

7

1 = Insertion direction

2 = Label area

3 = Write protection tab for a 1.44 Mbyte floppy disk

4 = Identification of a 1.44 Mbyte floppy disk or write protect switch on a 120 MB floppy disk

5 = Eject button for inserted floppy disks

6 = Disk is write-protected

7 = Disk is not write-protected

To insert a diskette

► Push the floppy disk into the drive in the insertion direction (1) until it engages. The label shouldbe facing upward.

To remove a diskette

► Push the eject button (5).

Protect the floppy disk against being overwritten or erased

► Slide the write-protect slider into position (6). The hole is now visible.

Deactivate write protection

► Slide the write-protect slider into position (7). The hole is now covered.

A26361-K1008-Z120-1-7619, edition 1 21


30/68

Operation

Settings in BIOS Setup

In BIOS Setup you can set the system functions and the hardware configuration of the device. Whenthe device is delivered, the default entries are valid (see "BIOS Setup" manual or manual for themainboard). You may customise these settings to your requirements in the BIOS Setup.

Property and data protection

Software functions and mechanical locking offer a broad range of functions for protecting your deviceand your personal data from unauthorised access. You can also combine these functions.

2

1

4

3

1 = Kensington Lock2 = Eye for padlock

3 = Casing unlocked4 = Casing locked

Unlocking and locking casing (optional)

With the casing lock (optional) you can mechanically lock the casing to prohibit unauthorised personsfrom opening it.

A description of how to install the casing lock is provided in the section "Installing casing lock".

22 A26361-K1008-Z120-1-7619, edition 1


31/68

Operation

Anti-theft protection and lead-sealing

Anti-theft protection

You can protect your device from theft.

● with the Kensington Lock device (1) and with a Kensington MicroSaver.Consult the manual for your Kensington Lock.

● with the eye (2), a padlock and a chain, which you have connected to a fixed objectbeforehand.

Lead-sealing

To prevent unauthorised persons from opening the casing, the casing can be sealed. To do this,feed a sealing chain through the eye (2) and seal the chain with the lead seal.

BIOS setup security functions

The Security menu in BIOS Setup offers you various options for protecting your personal data againstunauthorised access, e.g.:

● Preventing unauthorised BIOS Setup entry● Preventing unauthorised system access● Preventing system booting from the diskette drive● Activating virus warnings● Protecting BIOS from being overwritten● Protecting the device from being switched on by an external device

You can also combine these functions.

You will find a detailed description of the Security menus and how to assign passwords in the manual

for the mainboard or in the "BIOS Setup" manual.

A26361-K1008-Z120-1-7619, edition 1 23


32/68


33/68


!

Take note of the safety notes in the "Safety" manual and in the "Preparing for use" chapter, when you connect or disconnect cables.

If a fault occurs, try to correct it as described in the following places:

● in this chapter● in the documentation of the connected devices● in the help systems of the software used● in the documentation of your operating system

If you fail to correct the problem, proceed as follows:

► Switch off the device.

► Make a note of the steps and the circumstances that led to the fault.

► Make a note of any error messages displayed.

► Note the ID number of your device. The Ident-No. can be found on the type rating plate on theback of the casing.

► Contact your sales outlet or our customer service centre.

Installing new software

When installing programmes or drivers, important files may be overwritten and modified. To be ableto access the original data in the event of any problems following installation, you should backup

your hard disk prior to installation.

Power-on indicator remains unlit after you haveswitched on your device

This may be due to the following:

The mains voltage supply is faulty

► Check whether the power cable is plugged properly into the device and a grounded mains

outlet.► Switch the device on.

Internal power supply overloaded

► Pull the power plug of the device out of the mains outlet.

► Wait for a moment.

► Plug the power plug into a properly grounded mains outlet again.

► Switch the device on.

A26361-K1008-Z120-1-7619, edition 1 25


34/68


The device cannot be switched off with the ON/OFFswitch

Cause: The device has not been switched on with the ON/OFF switch.

► Press the ON/OFF switch again.

Cause: System crash

► Press the ON/OFF switch for at least 4 seconds, until the device switches off.

i

The operating system is not shut-down properly in the process. Error messages aretherefore possible the next time the system is booted.

The screen stays blank

If your screen remains blank this may be due to the following:

Monitor is switched off

► Switch your monitor on.

Power saving has been activated (screen is blank)

► Press any key on the keyboard.

or

► Deactivate the screen saver. If necessary, enter the appropriate password.

Brightness control is set to dark

► Adjust the brightness control. For detailed information, please refer to the operating manualsupplied with your monitor.

Power cable not connected

► Switch off the monitor and the device.

► Check that the monitor power cable is properly connected to the monitor and to a groundedmains outlet or to the monitor socket of the device.

► Check that the device power cable is properly plugged into the device and a grounded mains

outlet.

► Switch on the monitor and the device.

Monitor cable not connected

► Switch off the monitor and the device.

► Check that the monitor cable is properly connected to the device and monitor.

► Switch on the monitor and the device.

26 A26361-K1008-Z120-1-7619, edition 1


35/68


Wrong monitor has been set under Windows 2000

► Restart the device.

► If the message Starting Windows appears, press function key F8

The Windows 2000 Advanced Options Menu appears.

► Select Safe Mode or Safe Mode with Network .

► Set the correct values for the attached monitor as described in the operating manual of themonitor by selecting Start - Settings - Control Panel - Display - Settings.

Wrong monitor has been set under Window XP

► Restart the device.

► Press F8 while the system is booting.

Either the Windows Advanced Start Options menu or the menu for selecting the operating systemappears.

► If the menu for selecting the operating system appears, press F8 .

► Select Safe Mode or Safe Mode with Network .

► Set the correct values for the attached monitor as described in the operating manual of themonitor by selecting Start - Settings - Control Panel - Display and then the Appearance, Themes,Settings tabs.

The wrong RAM modules have been inserted

► See the manual for the mainboard for information on which memory modules can be used.

No mouse pointer displayed on the screen► Shut down the operating system properly.

► Switch off the device.

► Check that the mouse cable is properly connected to the system unit.

If you use an adapter or extension lead with the mouse cable, check the connections.

► Make sure that only one mouse is connected.

► Switch the device on.

The mouse controller must be enabled if you use a PS/2 mouse on the PS/2 mouse port .► Check in the BIOS Setup that the mouse controller is Enabled .

► Check that the mouse driver is properly installed and is present when the applicationprogramme is started. Detailed information can be found in the user guide for the mouse andapplication programme.

A26361-K1008-Z120-1-7619, edition 1 27


36/68


The floppy disk cannot be read or written

► Check that the write protection of the floppy disk or the floppy disk drive is activated (refer tothe "BIOS Setup" manual and if necessary to the technical manual for the mainboard).

► Check the relevant entries for floppy disk drive in the Main menu of the BIOS Setup.

► Check that the floppy disk drive controller is enabled (refer also to the technical manual for themainboard or in the "BIOS Setup" manual).

► Check that the cables of the floppy disk drive are properly connected (see "Installing andremoving the floppy disk drive").

Time and/or date is not correct

You can set the time and date in the BIOS Setup or in the operating system.

► Set the time and date.

i

If the time and date are repeatedly wrong when you switch on your PC, the on-boardbattery is flat. Change the lithium battery as described in the "Making changes on mainboard"-"Replacing lithium battery".

Error messages on the screen

Error messages and their explanation are contained:

● in the manual for the mainboard

● in the "BIOS Setup" manual● in the documentation for the programmes used

Restoring the hard disk contents

Should you need to restore your hard disk, the instructions are provided on the case of the"Recovery CD" (delivered with your system).

Tips

Out of system resources

If you have too many applications running at once, you may experience problems due to a lack ofsystem resources.

► Close unnecessary applications.

Or

► Run the applications in a different order.

Other manuals

Additional manuals are provided as PDF files on the "User Documentation" or "Drivers & Utilities"

CD.

28 A26361-K1008-Z120-1-7619, edition 1


37/68

System expansions

i

As the device has to be shut down in order to install/deinstall system hardwarecomponents, it is a good idea to print out the relevant sections of this chapter.

It may be necessary to update the BIOS when carrying out a system expansion orhardware upgrade. Additional information is contained in the "BIOS Setup" manual orpossibly in the manual for the mainboard.

When installing components that become very hot, make sure that the maximumpermissible temperature is not exceeded.

!

The device must be switched off when installing/removing the system expansions and maynot be in the energy-saving mode.

Remove the power plug before opening the device.

This chapter describes all the activities required to modify your device hardware (e.g. installingboards or drives).

Read the supplied documentation before installing new drives and/or boards.

Refer to the manual for the mainboard before making any extensions to the mainboard.

Information about boards

Take care with the locking mechanisms (catches and centring pins) when you are replacing boardsor components on boards.

To prevent damage to the board or the components and conductors on it, please take care when you

insert or remove boards. Make sure expansion boards are inserted straightly.

Never use sharp objects (screwdrivers) for leverage.

Boards with electrostatic sensitive devices (ESD) are identifiable by the labelshown.

When you handle boards fitted with ESDs, you must, under allcircumstances, observe the following points:

● You must always discharge static build up (e.g. by touching agrounded object) before working.

● The equipment and tools you use must be free of static charges.

● Always hold boards with ESDs by their edges.

● Never touch pins or conductors on boards fitted with ESDs.

A26361-K1008-Z120-1-7619, edition 1 29


38/68

System expansions

Opening the casing

► Switch off the device. The device must not be in the energy-saving mode!

! Please take note of the safety information in the "Important notes" chapter.

Pull the power plug out of the mains outlet!

1

2

► Remove any connected cables in the unitthat obstruct you.

► Lay the device on its right side.

► If necessary, unlock the casing.

► Press on the clip (1).

► Push the top cover in the direction of thearrow (2).

Closing the casing

► Push the top cover in the direction of thearrow until it engages.

► Return the system unit to its originalposition.

► Lock the casing again if necessary.

► If you have disconnected cables, reconnectthem to the connectors on the rear panel.

Installing casing lock

2 1

a

► Open the casing (see "Opening the casing").

► Place the removed side panel on a flatsurface with the inside facing upward.

► Press the catches (a) in the direction of thearrow (1).

► Carefully thread the lock out of the sidepanel in the direction of the arrow (2).

30 A26361-K1008-Z120-1-7619, edition 1


39/68

System expansions

a

b

► Thread the casing lock into the side panelwith the catch (a) first. Make sure that thecatch (a) slips into the slot.

► Press the casing lock once briefly andfirmly into the side panel in the direction of

the arrow so that the catches (b) engageproperly.

► Close the casing (see "Closing the casing").

If you want to remove the casing lock and install the simple closure, proceed accordingly.

Removing and installing the fanIf the device is equipped with a fan, you must remove the fan, e.g. to install and remove boards.

Remove the fan


1

2

3

► Press the catch in the direction of the arrow (1).

► Fold the fan forward in the direction of the arrow (2) and remove it from the casing in thedirection of the arrow (3).

► Disconnect the cables of the fan from the mainboard if necessary.

You have free access to the boards.

A26361-K1008-Z120-1-7619, edition 1 31


40/68

System expansions

Installing the fan

2

1

► Hook the fan into the hooks (1) in the baseof casing.

► Fold the fan in the direction of the arrow (2)

until it engages.

► Connect the previously disconnected fancable to the mainboard if necessary.


Installing and removing boards

!

Please take note of the section "Information about boards".

In the upper three slots you can install boards with a length of up to 230 mm, and in the lower slotboards with a length of up to 315 mm.

The number, position and arrangement of the board slots on the mainboard can be found in themanual for the mainboard. Boards may already be installed when the device is shipped.

32 A26361-K1008-Z120-1-7619, edition 1


41/68

System expansions

Installing a board


► Remove the fan casing if necessary (see "Remove the fan").

2

1

► Remove the screw (1).

► Remove the rear slot cover plate from the slot (2).

i

Do not dispose of the cover plate. If you remove the board again, you must reinstall therear slot cover plate (cooling, fire protection or EMC regulations to be complied with).

The top and the lowest slot are suitable for low-profile cards with an adapter.

► Take the new board out of its packaging.

► Make the required settings for the board.

A26361-K1008-Z120-1-7619, edition 1 33


42/68

System expansions

1

2

► Push the board up to its slot (1).

Ensure that the end of a long board without angle bracket fits into the corresponding guide ofthe casing.

► Press the board into the slot so that it engages.

► Fasten the board into place with the screw (2).

► If necessary, connect the cables.

► Reinstall the fan casing if necessary (see "Installing the fan").► Close the casing (see "Closing the casing").

i

If you have installed or removed a PCI board, check the relevant PCI slot settings in the BIOS Setup. If necessary, change the settings. Further information is provided in the PCIboard documentation.

34 A26361-K1008-Z120-1-7619, edition 1


43/68

System expansions

Removing a board


► Remove the fan casing if necessary (see "Remove the fan").

► Disconnect the cables connected to the board.

2

1

► Remove the screw (1).

► Remove the board from the casing (2).

► Place the board into appropriate packaging.

!

To ensure proper cooling, fire protection and observation of the relevant EMC(electromagnetic compatibility) regulations, you must mount a rear slot cover plate.

A26361-K1008-Z120-1-7619, edition 1 35


44/68

System expansions

2

1

► Push the rear slot cover plate into the slot (1).

► Fasten the rear slot cover plate with the screw (2).

► Reinstall the fan casing if necessary (see "Installing the fan").


i

If you have installed or removed a PCI board, check the relevant PCI slot settings in the BIOS Setup. If necessary, change the settings. Further information is provided in the PCIboard documentation.

Low-Profile boards

For units with a particularly low overall height, there are so-called low-profile boards with a slot coverwith a lower overall height to match the low-profile units. To also install these low-profile boards innormal board slots, you must mount a corresponding slot adapter beforehand To do this, you have tofirst remove the slot cover from the casing rear panel.

► Remove the slot cover from the casing rear panel (see "Removing a board") and undo thescrew that holds the slot cover together.

► Make the required settings for the board.

!

Do not dispose of the slot cover. If you remove the board again, you must reinstall the slotcover (cooling, fire protection or EMC regulations to be complied with).

36 A26361-K1008-Z120-1-7619, edition 1


45/68

System expansions

Mounting slot adapter

2

1

► Fit the slot adapter in the direction of thearrow (1) on the slot cover of the low-profileboard and fix it using the screw (2).

Now you can install the low-profile board in asuitable slot like a normal board (see "Installing aboard").

Removing slot adapter

2

1

► Unscrew the screw (1) and remove the slotadapter in the direction of the arrow (2).

A26361-K1008-Z120-1-7619, edition 1 37


46/68

System expansions

Installing an additional serial port

The condition is that the mainboard has a free internal serial port.

There are two ways of installing an additional serial port:

1. An additional serial interface can be installed in an angled installation bracket like a board.► Install the angled installation bracket with the serial port like a board (see "Installing a

board").

► Connect the cable of the additional serial port to the connector on the mainboard.

2. An installation opening for the serial port is provided on the rear panel of the casing. As a result,no board slot is occupied when a second serial port is installed.

► Insert a screwdriver into the opening and break out the pre-stamped installation openingby moving it backwards and forwards.

► Detach the pins of the serial port from the angled installation bracket.

► Secure the serial port to the rear panel of the device with the pins.

► Connect the cable of the additional serial port to the connector on the mainboard.

38 A26361-K1008-Z120-1-7619, edition 1


47/68

System expansions

Installing and removing drives

The PC casing can accommodate a total of six drives:

● four accessible drives(two 5 1/4 inch drives and two 3 1/2 inch drives)

● two non-accessible drives(both 3 1/2 inch drives with half installation height)

"Accessible drives" are e.g. DVD or CD ROM drives, into which a data carrier can be inserted fromoutside. Non-accessible drives are e.g. hard disks.

IDE drives

Four IDE drives are supported as standard equipment. Ideally, hard disks are connected to IDEinterface 1 and other drives (e.g. CD ROM drive) to IDE interface 2 (see also the manual for themainboard).

Installing an accessible drive


1

2

► Remove the screws (1) and take the blind insert out of the casing (2).

i

Do not dispose of the blind insert. If you remove the drive again later, you must reinstallthe blind insert (cooling, fire protection or EMC regulations to be complied with).

► Take the new drive out of its packaging.

► Adjust the required settings on the drive (if necessary, on already-installed drives as well).

A26361-K1008-Z120-1-7619, edition 1 39


48/68

System expansions

2

1

► Slide the drive into its bay (1).

► Fasten the drive into place with the screws (2).

► Plug the data and the power supply connectors into the drive. Make sure the polarity is correct.


i

It may be necessary to modify the entry for the drive in the BIOS Setup.

Removing an accessible drive


2

1

► Remove the screws (1), and take the drive out of the casing (2).

► Pull the data and the power supply connectors from the drive.

40 A26361-K1008-Z120-1-7619, edition 1


49/68

System expansions

1

2

► Push the blind insert into the casing (1).

► Secure the blind insert with the screws (2).

i


A26361-K1008-Z120-1-7619, edition 1 41


50/68

System expansions

Installing and removing the floppy disk drive


! Before you can replace the floppy disk drive, you must remove the power supply unit, see

the chapter "Removing the power supply".

2

1

► Remove the data and power supply connectors from the floppy disk drive.

► Remove the screws (1) from the floppy disk drive.

► Slide the floppy disk drive out of the casing in the direction of the arrow (2).

► Take the new floppy disk drive out of its packaging.

► Slide the new floppy disk drive into the case opposite the direction of the arrow (2).

► Fasten the floppy disk drive with the screws (1).

► Fit the data and power supply connectors to the floppy disk drive. Make sure the polarity iscorrect.

► Replace the power supply (see "Installing the power supply").


i


42 A26361-K1008-Z120-1-7619, edition 1


51/68

System expansions

Installing and removing hard disk with EasyChange rails


Removing the hard disk

21

1

► Press the EasyChange rails mounted on the hard disk together somewhat (1) and pull the harddisk out of the casing in the direction of the arrow (2).

► Disconnect all cables connected to the drive (data cable, power supply cable).

► Release the die EasyChange rails from thehard disk.

i



A26361-K1008-Z120-1-7619, edition 1 43


52/68

System expansions

Installing the hard disk

► Remove the new hard disk from the package.

► Make the required settings (e.g. master/slave, cable select) on the drives (hard disks).

► Secure the EasyChange rails on the side ofthe hard disk by inserting the upper pins of theEasyChange rail in the corresponding holes ofthe hard disk.

► Plug in the cables on the hard disk.

2

1

1

► Press the EasyChange rails mounted on thehard disk together somewhat (1) and slidethe hard disk into the casing in the directionof the arrow (2).


i


EasyChange rails for a second hard disk are mounted in the drive cage.

Installing an removing USB interfaces

You can install USB interfaces on the front and back of the device. You can also install audio ports

on the front of the device.

44 A26361-K1008-Z120-1-7619, edition 1


53/68

System expansions

Installing front USB audio interfaces

In the opening next to the floppy disk drive you can install two USB interfaces combined with twoaudio interfaces.

Each of the audio ports have the connections Headphone OUT and Microphone IN.

► Remove the cover.

2

1

► Push the USB or USB audio interface into the installation opening (1) and secure the USB orUSB audio interface with the screw (2).

► Connect the USB cable and, if necessary, the audio cable to the corresponding connector onthe mainboard (see also the manual for the mainboard).

1

► Remove the blind cover of the installationopening by pressing against it from theinside (1).

► Place the cover on the casing again (2).

A26361-K1008-Z120-1-7619, edition 1 45


54/68

System expansions

Removing front USB audio interfaces

1

2

3

4

► Disconnect the USB cable and, if necessary, the audio cable from the mainboard.


► Remove the screw (1) and pull the USB interface or the USB audio interface upwards out of thelocation (2).

► Reinsert the blind cover of the installation location in the cover opening (3) from the front.

► Place the cover on the casing again (4).

Installing USB interface at the rear side

An installation opening for the USB interface is provided on the rear panel of the casing. As a result,no board slot is occupied when a second serial port is installed.

1

► Insert a screwdriver into the opening and break out the pre-stamped installation opening bymoving it backwards and forwards.

► Slide the USB interface into the installation opening and secure it with the screw (1).

► Connect the USB cable to the mainboard.

46 A26361-K1008-Z120-1-7619, edition 1


55/68

System expansions

Installing/removing a SmartCard reader and/or WLANmodule (optional)

There is an installation opening on the front of the casing which you can use to install a SmartCard

reader and/or WLAN module. As a result, no board slot is occupied when a second serial port isinstalled.

i

The SmartCard reader and WLAN module can be installed together in the carrier.However, you can also install only one of the two boards. The WLAN module is installed inthe lower slot of the carrier and the SmartCard reader in the upper slot of the carrier. If youwant to install the SmartCard reader and the WLAN module together, first install the WLANmodule. Removal is carried out in the reverse order.

Screwing WLAN module onto carrier

2

a

a

1

2

► Push the WLAN module - with the

component side facing downwards - in thedirection of the arrow (1) into the guide (a).

► Fasten the WLAN module with thescrews (2).

Screwing SmartCard reader onto carrier

2

2

a

a

1

► Push the SmartCard reader - with thecomponent side facing downwards - in thedirection of the arrow (1) into the guide (a).

► Fasten the SmartCard reader with thescrews (2).

A26361-K1008-Z120-1-7619, edition 1 47


56/68

System expansions

Removing SmartCard reader from carrier

aa

1

1

► Loosen the screws (1).

► Pull the SmartCard reader out of the carrierin the direction of the arrow (2).

Removing WLAN module from carrier

1

1

► Loosen the screws (1).

► Pull the WLAN module out of the holder inthe direction of the arrow.

Installing SmartCard reader and/or WLAN module

2

1

► Open the casing (see "Opening thecasing").

► Remove the cover (1).

► Break the plastic cover (2) out of the cover.

► Insert a screwdriver into the opening andbreak out the pre-stamped installationopening by moving it backwards andforwards.

48 A26361-K1008-Z120-1-7619, edition 1


57/68

System expansions

► Slide the carrier into the casing in thedirection of the arrow.

1

► Fasten the holder with the screws (2).

► Place the cover on the casing again.

► Connect the cables (also see the manual forthe mainboard).


A26361-K1008-Z120-1-7619, edition 1 49


58/68

System expansions

Removing SmartCard reader and/or WLAN module

► Open the casing (see "Opening thecasing").

► Disconnect the cables.


1

► Remove the screws (1).

► Pull the holder out of the casing in directionof the arrow.

► Place the cover on the casing again.


50 A26361-K1008-Z120-1-7619, edition 1


59/68

System expansions

Extensions to the mainboard

Details on whether you can upgrade the main memory or the processor of your device are providedin the manual for the mainboard. To make the installation slots accessible, you may need to removethe power supply.

Installing and removing the power supply

Removing the power supply


► Remove the fan if necessary (see "Remove the fan").

1

2

► Remove the knurled screws (1) on the rearof the chasing.

► Disconnect the power cables, if connected,from the power supply (2).

The power connections are mechanically lockedwhen the power supply is removed.

1

► Loosen the knurled screws (1) on the sideof the power supply.

► Carefully pull the power supply out of the

casing.

A26361-K1008-Z120-1-7619, edition 1 51


60/68

System expansions

► Tilt and turn the power supply unit so that itengages in the mounting on the frontcasing.

!

The removed power supply may not be connected to the power system (danger ofelectrical shock)!

The power connections are mechanically locked when the power supply is removed.

Installing the power supply

1 2

► Tilt and turn the power supply unit (1) so that you can place the power supply in the casing.Watch the guide rails when doing so.

► Firmly press the power supply in the direction of the arrow (2) to deactivate locking of the powerconnections.

52 A26361-K1008-Z120-1-7619, edition 1


61/68

System expansions

4

3

► Fasten the knurled screws (3) on the side of the power supply.

► Fasten the knurled screws (4) on the rear of the chasing.

► Reinstall the fan casing if necessary (see "Installing the fan").


Making changes on mainboard


► Remove the power supply (see "Removing the power supply").

Upgrading main memory

► Upgrade the memory as it is described in the manual for the mainboard.

Replacing the processor

► Replace the processor as it is described in the manual for the mainboard.

Replacing lithium battery

In order to permanently save the system information, a lithium battery is installed to provide theCMOS-memory with a current. A corresponding error message notifies the user when the charge istoo low or the battery is empty. The lithium battery must then be replaced.

!

Incorrect replacement of the lithium battery may lead to a risk of explosion!

The lithium battery may be replaced only with an identical battery or with a typerecommended by the manufacturer.

Do not throw lithium batteries into the household waste. It must be disposed of inaccordance with local regulations concerning special waste.

Make sure that you insert the battery the right way round: The plus pole must be on thetop!

The lithium battery holder exists in different designs that function in the same way.

A26361-K1008-Z120-1-7619, edition 1 53


62/68

System expansions

2 3

1

23

► Press the catch in the direction of the arrow (1).

The battery jumps out of the holder slightly.

► Remove the battery (2).

► Push the new lithium battery of the identical type into the holder and press it downward until itengages.

Following changes► Replace the power supply (see "Installing the power supply").


54 A26361-K1008-Z120-1-7619, edition 1


63/68

Technical data

Electrical data

Regulations complied with: IEC 60950-1 / EN 60950-1 / VDE 0805 / UL 60950CSA 22.2 No.60950

Protection class: I

Rated voltage range: (selectable) 100 V -127 V / 200 V - 240 V

Frequency: 50 Hz - 60 Hz

Max. rated current● Casing with monitor socket

● Monitor socket (output)

100 V -127 V / 6.0 A200 V -240 V / 3.0 A

100 V -127 V / 3.0 A200 V -240 V / 1.5 A

Dimensions

Width/depth/height: 202 mm/376 mm/372 mm

Weight

with the basic configuration ca. 11 kg in basic configuration

Environmental conditions

Environment class 3K2Environment class 2K2

DIN IEC 721 part 3-3DIN IEC 721 part 3-2

Temperature:● Operating (3K2)● Transport (2K2)

15 °C to 35 °C-25 °C to 60 °C

Condensation in operating must be avoided.

Clearance required to ensure adequate ventilation:

● top● left● front● rear

min. 200 mmmin. 200 mmmin. 200 mmmin. 200 mm

A26361-K1008-Z120-1-7619, edition 1 55


64/68


65/68

Index

A Access permission, SmartCard 24

Accessible driveinstalling 39removing 40

Additional serial port, installing 38 Add-on modules 29 Alphanumeric keypad 19 Anti-theft protection 23 Audio input 14 Audio output 14

B Battery 53

BIOS Setup 22configuration 22security functions 23setting 22system settings 22

Board 29installing 33removing 35

Button, ON/OFF switch 20

C

Cableconnecting 13disconnecting 13

Casingclosing 30lead-sealing 23locking mechanically 22opening 30unlocking and locking 22

Casing lock 22installing 30

CD-ROM driveindicator 19installing 39removing 40

CD-ROM indicator 19CE certificate 4CE marking 4Chain 23Class B Compliance Statement 5Clearance 55

Connectingdevice 10

keyboard 10mouse 9PS/2 mouse 9standard keyboard 10USB keyboard 10

Contents of delivery 7Ctrl+Alt+Del 20Cursor keys 19

D Data

electrical 55

technical 55Data protection 22Date, not correct 28Device

Anti-theft protection 23cannot boot 25checking rated voltage 10cleaning 3closing 30connecting 10, 13connecting external devices 13

extensions 29indicators 18lead-sealing 23opening 30ports 14setting up 8switching off 17switching on 12, 17transporting 3

Device driversparallel port 15serial port 15

USB 15Devices

connecting 13, 15Dimensions 55Disposal 4Drive

accessibleinstalling 39removing 40

DVD drive, indicator 19DVD indicator 19

A26361-K1008-Z120-1-7619, edition 1 57


66/68

Index

E Electromagnetic compatibility 4EMC, Electromagnetic compatibility 36Energy saving 4Environmental conditions 55Environmental data 55

Ergonomic, video workstation 8Error

date 28device 25mouse 27screen 26time 28

Error message 28ESD 29External devices

connecting 13, 15

ports 14

F Fan

installing 32removing 31

FCC statement 5Floppy disk

inserting 21removing 21working with 21write-protection 21write-protection, disabling 21

Floppy disk drivechanging 42indicator 19removing 40

Function keys 19

G Game port 14

H Hard disk

installing 43, 44removing 43

Hard disk contents, restoring 28Hard disk indicator 18Headphones 14

I IDE drives 39Important notes 3Indicators

device 18hard disk 18

Installingsoftware 11, 12switching on for the first time 11

Interfaces 14

K

Kensington Lock 23Key

Alt Gr 20Control 20Ctrl 20cursor keys 19Enter 20enter key 20Num 20Return 20Shift 20

Key combination 20Keyboard 19

alphanumeric keypad 19connecting 10cursor keys 19function keys 19numeric keypad 19port 8, 10

Keyboard port 14Keys 20

Ctrl key 20Ctrl+Alt+Del 20Menu key 20Shift key 20Start key 20

L LAN port 14Lead-sealing 23Line in 14Line out 14Lithium battery 51

replacing 53

Lock 22Low voltage directive 4Low-profile boards 36

mounting slot adapter 37removing slot adapter 37

M Main memory 51Main memory, upgrading 53Mainboard, extensions 51Manuals, further 28

58 A26361-K1008-Z120-1-7619, edition 1


67/68

Index

Memoryinsufficient 28not enough 28

Memory, upgrading 53Microphone jack 14Monitor

connecting 8no screen display 26port 8remains blank 26switching off 17switching on 12, 17transporting 3

Monitor port 14Mouse

connecting 9error 27

pointer 27port 8, 14

N New installation, software 25New software, installing 25Noise level 55Notational conventions 2Notes

boards 29CE certificate 4disposal 4energy saving 4important 3recycling 4safety 3

Numeric keypad 19

O ON/OFF switch 17, 20Operation 17Other manuals 28

P

Packing material 7unpacking 7

Parallel port 14, 15connecting devices 15settings 15

Port,, SCSI 14Power supply, installing 52Power supply, removing 51

Power-on indicator 17, 18dark 25fails to light 18, 25flashes 18lights green 18lights orange 18

Preparing for first use, overview 7Preparing for use 7

overview 7Printer 14Processor 51

replacing 53Property protection 22PS/2 mouse

connecting 9port 8, 9

PS/2 mouse port 14

R Ready-to-operate 17Recycling 4Retransportation 3

S Safety 3SCSI port 14Security functions

BIOS Setup 23

SmartCard 24SmartLock 24Security measures 22Serial port 14, 15

connecting devices 15settings 15

Setup, see BIOS SetupSigns and symbols 2SmartCard reader 47

indicator 19installing 47, 48removing 47, 50

Softwareinstalling 11, 12new installation 25

Standard keyboard, connecting 10Summer time 28Surface 55System board see mainboardSystem expansion 29System password 17System settings, BIOS Setup 22

A26361-K1008-Z120-1-7619, edition 1 59


68/68

Index

T Technical data 55Time

daylight savings 28not correct 28

Tips 25, 28

Transport 3Trouble

Device 25mouse 27screen 26

Troubleshooting 25

U USB 8USB audio port

installing 45

removing 46USB devices

connecting 15software 15

USB port 9, 10, 15connecting devices 15connecting keyboard 10connecting mouse 9installing 46rear panel of the casing 46

USB, Universal Serial Bus 14

V Ventilation area 8, 55Video workstation 8

W Warm boot 20Weight 55Wireless LAN module

installing 47, 48

removing 50WLAN module

installing 47, 48removing 50

Write protection, floppy disk 21

Documents

Fts Esprimopoperatingmanualen 10 1079143