2
G420 LA6X2 HSA S P E C I F I C A T I O N ENGINE Scania DC12 - 06 4 stroke, 6 Cylinder in-line direct injection diesel engine with electronic unit injectors, turbocharger and charge cooler. Maximum power 420hp (309kW) at 1700-1800rpm Maximum torque 2000Nm at 1100 - 1300rpm Swept volume Bore and stroke 127 x 154 mm Valves per cylinder 4 Cylinder heads 6 Compression level 1:18 11705cm3 Emission level Euro 3 COOLING SYSTEM Radiator with expansion tank Temperature regulated electronic cooling fan FUEL TANK 2 x 500 litres aluminium PROPELLER SHAFT Scania P500 FRONT AXLE Scania AM920 8500kg capacity parabolic springs 3 x 29 REAR AXLE 1 x Scania ADAA1501P pressed steel axle housing with ASA 1000 Tag Axle and magnetic oil filler plug with air spring suspension with 19 000kg capacity. Oil filter on both rear axles. CENTRAL GEAR Scania RB835 Spiral bevel single reduction hypoid type 3.96:1 rear axle ratio with differential locks Specifications subject to change without notice GEARBOX Scania GRS900R, 14 speed range change splitter synchromesh gearbox with two crawler gears and built in retarder with oil cooler and oil filter. CLUTCH Scania K432 single dry plate diaphragm pull type. With overload warning and wear protection Manufacturers capacity (kg) Axle load front, max. 8000 Bogie load rear, max. 19000 Gross vehicle mass, max. 27500 Front axle – rear edge of cab 858 (Z) Chassis Width (mm) 2550 (W) Chassis Weight (kg) Front Rear Total Dimensions (mm) Axle distance 3300 (A) Overhang, front 1455 (I) Overhang, rear 780 (J) Chassis, length 6860 (G) Bogie Spread (B) Over all Height (O) Dimensions (mm) 3288 1305 5402 3673 9075 Legal Technical 7500 18000 25500

G420 LA6X2MSA_tcm103-136668

Embed Size (px)

Citation preview

Page 1: G420 LA6X2MSA_tcm103-136668

G420 LA6X2 HSAS P E C I F I C A T I O N

ENGINEScania DC12 - 06 4 stroke, 6 Cylinder in-line direct injection diesel engine with electronic unit injectors, turbocharger and charge cooler.

Maximum power 420hp (309kW) at 1700-1800rpmMaximum torque 2000Nm at 1100 - 1300rpmSwept volumeBore and stroke 127 x 154 mm Valves per cylinder 4Cylinder heads 6Compression level 1:18

11705cm3

Emission level

Euro 3

COOLING SYSTEMRadiator with expansion tankTemperature regulated electronic cooling fan

FUEL TANK2 x 500 litres aluminium

PROPELLER SHAFTScania P500

FRONT AXLEScania AM9208500kg capacity parabolic springs 3 x 29

REAR AXLE1 x Scania ADAA1501P pressed steel axle housing withASA 1000 Tag Axle and magnetic oil �ller plug with airspring suspension with 19 000kg capacity.Oil �lter on both rear axles.

CENTRAL GEARScania RB835 Spiral bevel single reduction hypoid type 3.96:1 rear axle ratio with di�erential locks

Speci�cations subject to change without notice

GEARBOXScania GRS900R, 14 speed range change splitter synchromesh gearbox with two crawler gears and built in retarder with oil cooler and oil �lter.

CLUTCHScania K432 single dry plate diaphragm pull type.With overload warning and wear protection

Manufacturers capacity (kg)Axle load front, max. 8000Bogie load rear, max. 19000Gross vehicle mass, max. 27500

Front axle – rear edge of cab 858 (Z)

Chassis Width (mm) 2550 (W)

Chassis Weight (kg)FrontRearTotal

Dimensions (mm)

Axle distance 3300 (A)Overhang, front 1455 (I)

Overhang, rear 780 (J)Chassis, length 6860 (G)

Bogie Spread (B)

Over all Height (O)

Dimensions (mm)

3288

1305

5402 3673 9075

Legal Technical 75001800025500

Page 2: G420 LA6X2MSA_tcm103-136668

G420 LA6X2 HSAS P E C I F I C A T I O N

Call Centre: 0800 005 798 Tel: (011) 661-9600 www.scania.co.za

Speci�cations subject to change without notice

BRAKES ABS Direct acting full air drum brakes with independent front rear and parking circuits.Asbestos free linings with manual slack adjusters.

PARKING BRAKEDiaphragm/spring brake on front axle and leading rear axle.

EXHAUST BRAKEAutomatic control. Operational in conjunction with retarder and service brakes.

FRAMEF950 heavy duty reinforced providing maximum accessibility for servicing, single member.

STEERINGRight hand drive, hydraulic power steering having a ratio of 18.6:1.Adjustable steering column for height and rake.Steering column lock.

SUSPENSIONFront Parabolic 3 x 29 / AM920N with 8500kg capacity.Air suspension with 19 000kg capacity.

SHOCK ABSORBERSDouble acting on front axle and rear axle

ELECTRICS24 Volt system, 180Ah batteries.80A alternator with built-in recti�erMaster switch single pole, chassis mounted.

CABCG19N double bunk mech. suspended sleeper cab of modern, pleasing design, manufactured to very rigid Swedish safety regulations. Cab sheet is made of hot dipped galvanised steel. 4 point mechanical suspensionCab Colour, Scania white, grill colour grey

COMPRESSORAPS air management systemGear driven 2 cylinder water cooled knorr 600Air system with air dryer

AIR TANKSSeparate air tanks for each circuit.

HORNElectric controlled air horn, bumper mounted.Roof Mounted air horn.

INSTRUMENTSOne day tachograph with rev counter, tachometer, gauges for air pressure circuits, coolant temperature, voltmeter, oil pressure.Warning lights for oil pressure, coolant temperature, direction indicators, di�erential locks, Taco 1 Day Recs VDO

SUPPLIED/FITTED AS STANDARDCab air conditioningHeater and demisterElectric windscreen washerFog lamps, Spotlamps, Reverse lamp, �fth wheel lightElectric windows, Central locking, Tinted windscreenElectrically adjustable mirror – left hand sideAir sprung driver and passenger seatsWheel nut cover stainless steelWheel nut capsHose for tyre in�ationJack and handle, wheelspanner and tommy barLockable fuel �ller capsExhaust brake automatic controlSplash guards behind front wheelsWhite smoke limiterOne �re extinguisher in cab 2kgCab roof hatchCatwalk between 5th wheel and cabTrailer dump valveClutch overload warningClutch wear ProtectionHeated mirrorsSpeed limiter

OPTIONAL EXTRA EQUIPMENT

Opticruise driveline management systemAir suspension on rear axlesRepair and Maintenance contractAIR CLEANER

Air cleaner with safety �lter, high intake

Front CD loader, FM radioTinted windows

WHEELS AND TYRES3 x 315/80 x 22.5 front (steering pattern) & spare with8 x 315/80 x 22.5 rear (traction pattern) – all steel belttubeless radial, mounted on 9.0 x 22.5 aluminium rims

TURNING CIRCLEKerb 7358 mmWall to Wall 8017 mm

ADR specifications