Upload
vuongngoc
View
219
Download
2
Embed Size (px)
Citation preview
Gabriel First Corp. • East Rochester, NY 14445-0191 • 585-381-7000 • 800-873-2000
FAX: 585-383-6362 • e-mail: [email protected]
Apply Today _ Play Tomorrow
Court Mate Series No. 3434
Quick & Easy Spreading
T-Bar
Applicator
Frame
Spreader
Sleeve
Gym FinishGym Finish
Application Procedure ManualApplication Procedure ManualGym FinishGym Finish
Application Procedure ManualApplication Procedure Manual
High-Gloss Ready-To-Use Water-Base Urethane
Wood Finish With Excellent Sneaker Traction.
Its Clear & Durable... Lasts For Many Years.
Court Mate Truly Outperforms Conventional
Oil-Modified Gym Finishes Without The Smell.
IndexPage Description
2 Introduction & Peeling Spots
3 Apply Court Mate Autoscrubber Cleaning
4 Apply Court Mate - Floor Machine Cleaning
5 Burnish Court Mate - Autoscrubber Cleaning
6 Burnish Court Mate Floor Machine Cleaning
7 Court Mate Supplies Information
Procedure Manual
One-Day Court Restoration
Gabriel Court Mate
2
Until Court Mate, restoring the gloss to a gym or court wood floor was a tedious, drawn-out, and dusty task. Offensive odor and
drying times running into days were normal. Because of the time and energy it took to restore a scratched and dull floor, a
medium to poor looking shine had to be acceptable. Too many coats of an amber colored oil-based urethane would cause
finished wood floors to become prematurely dark and in need of expensive and time-consuming sanding and refinishing.
Court Mate has changed everything... The time-consuming and frustrating upkeep steps have been converted to a one-day
process that allows a team of three to prepare a 10,000 square foot wood gym floor and apply three coats of Court Mate.
The wood floor is ready for sports action the next morning.
When it’s time to restore the shine, just wash the floor, let it dry, and burnish it to its original shine.
Fantastic results with fantastic savings. Everyone will be pleased; Coaches, Players, and Administrators.
Gabriel Court Mate Gym Finish is a breakthrough in waterborne technology.
Important: Court Mate is to be used on floors already covered with wood finish. Freshly-sanded floors first need to be
primed with Gabriel Big-10 Sealer and then have at least 2 coats of Big-10 Gym Finish applied over the court lines.
Always consult the Gabriel Technical Service Department for assistance.
Gabriel First Corp. • East Rochester, NY 14445 • 585-381-7000 • 800-873-2000 • FAX: 585-383-6362
Lift Loose Material
Dealing With Old Finish Peel Spots
Peeling is the symptom of poor adhesion between coats which cannot
be corrected unless the floor is sanded. Prior to applying Court Mate,
an effort should be made to fill in any peeled spots with the “old” product
in an effort to better balance the darkening of the “old” gym finish as
well as fill in what normally ends up as an easy-to-notice depression.
The results will be worth the effort.
Scrape Down Edges 120 Grit Screen Run Disc Over Spot Remove Disc Dust
Tack Clean & Let Dry Paint In “Old” Sealer Lightly Hand Sand Prepare Entire Floor Apply Court Mate
24 Hours Later
Next... Follow A Procedure In This Manual
Steps For Working On Peeled Spots
Imagine It: “Wet Look” Wood Floors... AlwaysImagine It: “Wet Look” Wood Floors... Always
1
2 3
4 5
6 7
8
MATERIALS & EQUIPMENT
If You Are Repairing Peeled Spots Prior To Preparing Floor For Application of Court Matea. Putty Knife & Sharp Pocket Knife with Long Blade
b. Floor Machine with Drive Pad & 120 Grit Disc(s)
c. Hand Sanding Block with Cut Up 120 Grit Screen
d. Leftover Gym Finish From Previous Application
e. Clean “Coffee Can” & Artist’s Brush
1. Gabriel Fast-1-2-3 Detergent
2. Gabriel CM Floor Conditioner
3. Gabriel Court Mate Gym Finish
4. Auto Scrubber with Pad Holder & “like new” squeegee
Thick Brown or Thick Black Scrubbing Pads
5. Water Can (sprinkler removed) or Special Dispensing Bucket
6. Clean Wet Mop or Microfiber Damp Mop
7. Frame & Handle for #6 above
8. T-Bar Finish Application System
a. Handle & Bar
b. Foam Pad Bar Cover
9. Clean Dust Pan to pick up extra Court Mate when ending
10. Dust Mop Tool Frame(s) & Handle(s)
11. Microfiber Dust Mops to fit #10
12. Clean Wiping Cloths & Polyliner For Soiled Cloths
13. Dust Pan & Bench Brush
14. Walk-Off Mat On Which To Wipe Feet
15. Wet Mop(s), Handle(s), Mop Bucket(s), & Gear Wringer(s)
16. Throw-Away Gloves & Any Required Safety Devices
1. Remove gum, tape, etc. & Dust Mop Floor.
2. Fill one mop bucket with fresh cold water.
3. Fill another mop bucket with fresh cold water and mix in
CM Floor Conditioner @ 8 oz. per gallon of water.
5. Fill Auto Scrubber with fresh cold water and mix in Fast-1-2-3
@ ½ oz. per gallon of water.
6. Spread CM Floor Conditioner Solution onto the floor
using a mop & bucket or a solution-dispensing (Material # 5)
device & Microfiber Flat Damp Mop.
7. Let the solution set on the floor for 5 minutes and then
commence scrubbing with Auto Scrubber using brown or
black pads... do not vacuum up scrubbed solution.
Check your scrubbing pads along the way to make
sure that there is nothing caking up in the pad holes.
Do not allow the scrubbing solution to dry on the floor.
Break the floor area down into workable sections.
8. Rescrub the area you just completed scrubbing - But this
time, release the Fast-1-2-3 solution onto the floor, scrub,
and vacuum up.
9. Thoroughly damp Mop the entire floor with fresh cold water.
Change water when you no longer see bottom of bucket.Allow Floor To Dry Thoroughly
Before beginning the application of Court Mate, give thought
as to where are the best starting and ending points.
Prepare Wood Floor For Application of Court MateOver A Sanded, Sealed, & Lined Floor • Using An Autoscrubber Machine
Procedure No. CDL-1104A
THIS PROCEDURE, FOR THE APPLICATION OF PRODUCTS MENTIONED HEREIN, HAS BEEN FOUND TO BE SUCCESSFUL BY GABRIEL.
HOWEVER, GABRIEL EXPRESSLY EXCLUDES ANY AND ALL WARRANTIES, GUARANTEES, OR REPRESENTATIONS WHATEVER,
WRITTEN OR OTHERWISE, INCLUDING IMPLIED WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE AND MERCHANTABILITY.
USER OF THIS PROCEDURE ASSUMES THE ENTIRE RISK FOR RESULTS OBTAINED FROM THE USE OF ANY PRODUCTS IN
CONJUNCTION WITH THIS PROCEDURE. SINCE THIS PROCEDURE IS WRITTEN ONLY AS A PRODUCT USAGE GUIDE, IT IS
YOUR RESPONSIBILITY TO MAKE SURE THAT PROPER SAFETY CLOTHING IS WORN BY ALL WORKERS AND THAT CURRENTLY
PRESCRIBED CHEMICAL USAGE PROCEDURES ARE FOLLOWED.
Important: This procedure is for a floor that already has a wood finish on it. If you are beginning with a freshly-sanded wood floor, it
will need to be conditioned with an oil-modified sealer... Consult the Gabriel Technical Service Department for the correct procedure.
Peel spots caused by the old finish lifting: Bevel edges by scraping with a knife blade, pass over spot with floor machine
& 120 grit screen disc, wash, and touch up with old finish. Next day: Hand sand lightly. Then begin with step 1 below.
Gabriel First Corp. • East Rochester, NY 14445 • 585-381-7000 • 800-873-2000 • FAX: 585-383-6362
10. Shake each container of Court Mate well before pouring
into Dispensing Can or Bucket.
11. One person needs to apply a bead of Court Mate, in the
direction of the wood grain, for the full length of the floor.
12. Another person needs to follow immediately and spread the
Court Mate by pulling the T-Bar Applicator in the direction
of the wood grain. To ensure a nice even spread, Do Not
allow the bead of Court Mate to flow past the center of the bar.
Very Important: Keep a “wet edge” and move steadily
without interruption. Do Not take more than 15 minutes before
returning to the wet edge at your starting point.
When finished and there is a puddle of Court Mate: Wear
throw-away gloves and with a clean cloth and dust pan, pick up
excess Court Mate. Finish off with T-Bar.
Wait at least 1 hour after completing each coat before
applying the next coat. No more than 3 coats in one day.
PROCEDURE
Wash Equipment & Pads
Thoroughly Using Water.
3
MATERIALS & EQUIPMENT
If You Are Repairing Peeled Spots Prior To Preparing Floor For Application of Court Matea. Putty Knife & Sharp Pocket Knife with Long Blade
b. Floor Machine with Drive Pad & 120 Grit Disc(s)
c. Hand Sanding Block with Cut Up 120 Grit Screen
d. Leftover Gym Finish From Previous Application
e. Clean “Coffee Can” & Artist’s Brush
1. Gabriel Fast-1-2-3 Detergent
2. Gabriel CM Floor Conditioner
3. Gabriel Court Mate Gym Finish
4. Rotary Floor Machine with Pad Holder
Brown or Black Scrubbing Pads (Not Thin Black Stripping Pad)
5. Water Vacuum with A “like new” Squeegee
6. Wet Mop(s), Handle(s), Mop Bucket(s), & Gear Wringer(s)7. Frame & Handle for #6 above
8. T-Bar Finish Application System
a. Handle & Bar
b. Foam Pad Bar Cover
9. Clean Dust Pan to pick up extra Court Mate when ending
10. Dust Mop Tool Frame(s) & Handle(s)
11. Microfiber Dust Mops to fit #10
12. Clean Wiping Cloths & Polyliner For Soiled Cloths
13. Dust Pan & Bench Brush
14. Walk-Off Mat On Which To Wipe Feet
15. Wet Mop(s), Handle(s), Mop Bucket(s), & Gear Wringer(s)
16. Throw-Away Gloves & Any Required Safety Devices
1. Sweep or Dust Mop Floor Thoroughly.
2. Fill one mop bucket with fresh cold water.
3. Fill another mop bucket with fresh cold water and mix in
CM Floor Conditioner @ 8 oz. per gallon of water.
4. Fill another mop bucket with fresh cold water and mix in
Fast-1-2-3 @ ½ oz. per gallon of water.
5. Spread CM Floor Conditioner solution (Step 3) onto the
floor using a wet mop.
6. Let the solution set on the floor for 5 minutes and then
commence scrubbing with a Floor Machine using a thick
Brown or Black scrubbing pad.
Check the scrubbing pads along the way to make sure
that there is nothing caking up in the pad holes.
Do not allow the scrubbing solution to dry on the floor.
Break the floor area down into workable sections.
7. Spread the Fast-1-2-3 solution (Step 4) onto the floor
using a clean wet mop.
8. Rescrub using thick Brown or Black scrubbing pads.
Vacuum up spent solution immediately.
9. Thoroughly damp Mop the entire floor with fresh cold water.
Change water when you no longer see bottom of bucket.Allow Floor To Dry Thoroughly
Before beginning the application of Court Mate, give thought
Prepare Wood Floor For Application of Court MateOver A Sanded, Sealed, & Lined Floor • Using A Hand-Held Floor Machine
Procedure No. CDL-1104B
THIS PROCEDURE, FOR THE APPLICATION OF PRODUCTS MENTIONED HEREIN, HAS BEEN FOUND TO BE SUCCESSFUL BY GABRIEL.
HOWEVER, GABRIEL EXPRESSLY EXCLUDES ANY AND ALL WARRANTIES, GUARANTEES, OR REPRESENTATIONS WHATEVER,
WRITTEN OR OTHERWISE, INCLUDING IMPLIED WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE AND MERCHANTABILITY.
USER OF THIS PROCEDURE ASSUMES THE ENTIRE RISK FOR RESULTS OBTAINED FROM THE USE OF ANY PRODUCTS IN
CONJUNCTION WITH THIS PROCEDURE. SINCE THIS PROCEDURE IS WRITTEN ONLY AS A PRODUCT USAGE GUIDE, IT IS
YOUR RESPONSIBILITY TO MAKE SURE THAT PROPER SAFETY CLOTHING IS WORN BY ALL WORKERS AND THAT CURRENTLY
PRESCRIBED CHEMICAL USAGE PROCEDURES ARE FOLLOWED.
Important: This procedure is for a floor that already has a wood finish on it. If you are beginning with a freshly-sanded
wood floor, it will need to be conditioned with Gabriel Big-10 oil-modified wood finish system.
Peel spots caused by the old finish lifting: See step-by-step photo procedure on page 2.
Wash Equipment & Pads Thoroughly Using Water.
Always call the Gabriel Technical Department whenever you need assistance.
Gabriel First Corp. • East Rochester, NY 14445 • 585-381-7000 • 800-873-2000 • FAX: 585-383-6362
as to where are the best starting and ending points.
10. Shake each container of Court Mate well before pouring
into Dispensing Can or Bucket.
11. One person needs to apply a bead of Court Mate, in the
direction of the wood grain, for the full length of the floor.
12. Another person needs to follow immediately and spread the
Court Mate by pulling the T-Bar Applicator in the direction
of the wood grain. To ensure a nice even spread, Do Not
allow the bead of Court Mate to flow past the center of the bar.
Very Important: Keep a “wet edge” and move steadily
without interruption. Do Not take more than 15 minutes before
returning to the wet edge at your starting point.
When finished and there is a puddle of Court Mate: Wear
throw-away gloves and with a clean cloth and dust pan, pick up
excess Court Mate. Finish off with T-Bar.
Wait at least 1 hour after completing the first coat before
applying the 2nd coat. No more than 2 coats in one day.
PROCEDURE
4
MATERIALS & EQUIPMENT
1. Gabriel CM Floor Conditioner & Measuring Cup
2. Auto Scrubber with Pad Holder & “like new” squeegee
Thick Green or Blue Scrubbing Pads
* 3. Propane Burnishing Machine
4. Court Mate Burnishing Pad(s)
5. Mop Bucket & Wringer
6. Clean Wet Mop & handle
7. Clean Dust Pan to pick up extra Court Mate when ending
8. Dust Mop Tool Frame(s) & Handle(s)
9. Microfiber Dust Mops to fit #8
10. Dust Pan & Bench Brush
11. Putty Knife, rags, & polyliner for trash
12. Walk-Off Mat On Which To Wipe Feet
13. Small water pail to hold a gallon or more of water.
14. Throw-Away Gloves & Any Required Safety Devices
1. Use putty knife to remove gum, tape, etc.
2. Sweep or Dust Mop Floor Thoroughly.
3. Fill a bucket with a gallon of fresh cold water and add in 8
oz. of CM Floor Conditioner. Mix well and use solution
to fill (and refill) a trigger spray bottle. Attach trigger
sprayer to bottle.
4. Fill Auto Scrubber supply tank with fresh cold water and mix
in CM Floor Conditioner @ 8 oz. per gallon of water.
5. Commence scrubbing and vacuuming with Auto Scrubber
using thick Green or Blue scrubbing pads.
Continue with step 5 until job has been completed.
Check your scrubbing pads along the way to make
sure that there is nothing caking up in the pad holes.
If solution spots remain after passing with the autoscrubber,
have someone with a bucket of fresh water and a clean,
As Needed UpkeepCleaning & Burnishing Court MateFloor Already Sealed With Court Mate • Using An Autoscrubber Machine
Procedure No. CDL-1104C
THIS PROCEDURE, FOR THE APPLICATION OF PRODUCTS MENTIONED HEREIN, HAS BEEN FOUND TO BE SUCCESSFUL BY GABRIEL.
HOWEVER, GABRIEL EXPRESSLY EXCLUDES ANY AND ALL WARRANTIES, GUARANTEES, OR REPRESENTATIONS WHATEVER,
WRITTEN OR OTHERWISE, INCLUDING IMPLIED WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE AND MERCHANTABILITY.
USER OF THIS PROCEDURE ASSUMES THE ENTIRE RISK FOR RESULTS OBTAINED FROM THE USE OF ANY PRODUCTS IN
CONJUNCTION WITH THIS PROCEDURE. SINCE THIS PROCEDURE IS WRITTEN ONLY AS A PRODUCT USAGE GUIDE, IT IS
YOUR RESPONSIBILITY TO MAKE SURE THAT PROPER SAFETY CLOTHING IS WORN BY ALL WORKERS AND THAT CURRENTLY
PRESCRIBED CHEMICAL USAGE PROCEDURES ARE FOLLOWED.
Important: This procedure is for a floor that already has Court Mate on it. For all other conditions, contact the Gabriel
Technical Service Department for further consultation.
Gabriel First Corp. • East Rochester, NY 14445 • 585-381-7000 • 800-873-2000 • FAX: 585-383-6362
well wrung out wet mop follow the autoscrubber mopping
up any wet spots.
6. When floor is dry... Walk the floor looking for any remaining
black marks. Using the hand sprayer, spray a mist of CM
Floor Conditioner solution onto the mark, let it set for 2
minutes, and rub out with a center core of a green or blue
pad. Pass over spot with a fresh-water-clean, wrung out
wet mop or absorbent wiping cloth.
Allow Floor To Dry Thoroughly
7. Burnish the floor using a propane machine with a Court Mate
burnishing pad. You may detail tight areas using an electric
burnishing machine and a Court Mate burnishing pad.
8. Dust Mop Floor Thoroughly.
PROCEDURE
* An electric burnishing machine (1500+ RPM) may be used for the entire job, but a one hour propane job may
take as much as 2 or 3 hours using an electric burnishing machine. Use same type Pad with either machine.
After burnishing...
If you wish to apply coat(s) of Court Mate, follow steps 10 through 12 on page 3 (Procedure CDL-1104A).
Wash Equipment & Pads Thoroughly Using Water.
Always call the Gabriel Technical Department whenever you need assistance.
5
MATERIALS & EQUIPMENT
1. Gabriel CM Floor Conditioner & Measuring Cup
2. Rotary Floor Machine with Pad Holder
3. Thick Green or Blue Scrubbing Pads
4. Wet Vac, hose, wand, & “like new” squeegee tool
* 5. Propane Burnishing Machine
6. Court Mate Burnishing Pad(s)
7. Mop Bucket & Wringer
8. Clean Wet Mop & handle
9. Clean Dust Pan to pick up extra Court Mate when ending
10. Dust Mop Tool Frame(s) & Handle(s)
11. Microfiber Dust Mops to fit #10
12. Dust Pan & Bench Brush
13. Putty Knife, rags, & polyliner for trash
14. Walk-Off Mat On Which To Wipe Feet
15. Small water pail to hold a gallon or more of water.
16. Throw-Away Gloves & Any Required Safety Devices
1. Use putty knife to remove gum, tape, etc.
2. Sweep or Dust Mop Floor Thoroughly.
3. Fill a bucket with a gallon of fresh cold water and add
in 8 oz. of CM Floor Conditioner. Mix well and use solution
to fill (and refill) a trigger spray bottle. Attach trigger
sprayer to bottle.
4. Fill a large mop bucket with fresh cold water and mix in
CM Floor Conditioner @ 8 oz. per gallon of water.
5. Liberally apply step 4 solution onto a workable section of
the floor. Let set for 5 minutes.
6. Commence scrubbing with the rotary floor machine using
thick Green or Blue scrubbing pads.
7. Vacuum up scrubbed solution immediately.
Do Not allow to dry on the floor.
Follow steps 5 through 7 until job is completed.
Check your scrubbing pads along the way to make
sure that there is nothing caking up in the pad holes.
Procedure No. CDL-1104D
THIS PROCEDURE, FOR THE APPLICATION OF PRODUCTS MENTIONED HEREIN, HAS BEEN FOUND TO BE SUCCESSFUL BY GABRIEL.
HOWEVER, GABRIEL EXPRESSLY EXCLUDES ANY AND ALL WARRANTIES, GUARANTEES, OR REPRESENTATIONS WHATEVER,
WRITTEN OR OTHERWISE, INCLUDING IMPLIED WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE AND MERCHANTABILITY.
USER OF THIS PROCEDURE ASSUMES THE ENTIRE RISK FOR RESULTS OBTAINED FROM THE USE OF ANY PRODUCTS IN
CONJUNCTION WITH THIS PROCEDURE. SINCE THIS PROCEDURE IS WRITTEN ONLY AS A PRODUCT USAGE GUIDE, IT IS
YOUR RESPONSIBILITY TO MAKE SURE THAT PROPER SAFETY CLOTHING IS WORN BY ALL WORKERS AND THAT CURRENTLY
PRESCRIBED CHEMICAL USAGE PROCEDURES ARE FOLLOWED.
Important: This procedure is for a floor that already has Court Mate on it. For all other conditions, contact the Gabriel
Technical Service Department for further consultation.
Gabriel First Corp. • East Rochester, NY 14445 • 585-381-7000 • 800-873-2000 • FAX: 585-383-6362
If solution spots remain after vacuuming, have someone
with a bucket of fresh water and a clean, well wrung out
wet mop pick up any wet spots.
8. When floor is dry... Walk the floor looking for any remaining
black marks. Using the hand sprayer, spray a mist of
CM Floor Conditioner solution onto the mark, let it set
for 2 minutes, and rub out with a center core of a green
or blue pad. Pass over spot with a fresh-water-clean,
wrung out wet mop or absorbent wiping cloth.
Allow Floor To Dry Thoroughly
9 Burnish the floor using a propane machine with a
Court Mate burnishing pad. You may detail tight areas
using an electric burnishing machine and a Court Mate
burnishing pad.
10. Dust Mop Floor Thoroughly.
PROCEDURE
* An electric burnishing machine (1500+ RPM) may be used for the entire job, but a one hour propane job may
take as much as 2 or 3 hours using an electric burnishing machine. Use same type Pad with either machine.
After burnishing...
If you wish to apply coat(s) of Court Mate, follow steps 10 through 12 on page 3 (Procedure CDL-1104A).
Wash Equipment & Pads Thoroughly Using Water.
Always call the Gabriel Technical Department whenever you need assistance.
6
As Needed UpkeepCleaning & Burnishing Court MateFloor Already Sealed With Court Mate • Using A Rotary Floor Machine
7
Court Mate is extremely easy to apply. The beauty of Court Mate is that it is a one-part system (no part A & B mixing)
that allows you to use up only the amount you need and save whatever is not poured from the container. Once the cur-
rent “old” wood floor finish has had black marks, tape, gum, etc. removed and has been thoroughly washed, wet mopped,
and allowed to dry, it is ready for a one, two, or three coats of Court Mate in a single day. Allow at least one hour between
coats; humid days will lengthen the drying time.
Graphic Overview For Applying Court Mate
Containers, tools, equipment, and casters must be clean and in excellent working condition.
Gabriel Court Mate - Application Hints & Product Information
Gabriel First Corp. • East Rochester, NY 14445 • 585-381-7000 • 800-873-2000 • FAX: 585-383-6362
Shake
Container
Well Prior
To Opening
1
Pour
Smoothly
Without Air
Gulping
2
Dispense
Parallel To
Wood Grain In
An Even Bead
Weighted
T-Bar &
HandleOnly
3 4Don’t
Let Product
Go Past
Middle
Move In Direction of Wood Grain
Soil
Will Leave
Permanent
Blemishes
Keep Everything Perfectly Clean
Rock
Handle To
Wring Out
Excess
5
Whenever Making A Direction Turn
Court Mate & Related Products
T-Bar Sleeve
12”... 3434-9021
18”... 3434-9023
24”... 3434-9025
12”... 3434-9001
18”... 3434-9003
24”... 3434-9005
Court Mate Mobile
Dispensing Bucket
With SpigotItem No. 2468-0401
Other Court Mate Products
CM Floor Conditioner 1 GL 3434-2101
Fast-1-2-3 Detergent Concentrate 750
120 Grit Screen Discs Available In Most Sizes
Black, Brown, Green, Blue Pads Available In Most Sizes
Microfiber Dust Mops Available In Most Sizes
CM Burnishing Pads 1215-35
Most every product on the procedures are available from Gabriel.
5 Gallon
Court Mate
Item No.3434-2005
Spigot
Handle
Spigot
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
________________________________________________________________________________________________________________________
Free Technical Assistance - 800-873-2000
NOTES
CM-20050407-01
Gabriel First Corp. • East Rochester, NY 14445-0191 • 585-381-7000 • 800-873-2000
FAX: 585-383-6362 • e-mail: [email protected]