SafeRacks® Garage ShelvingAssembly Instructions24”x92”x84” • 24”x72”x84 • 24”x48”x84

If you have any questions regarding your installation, please call:

877-655-3443 or go to www.SafeRacks.com

500LBSPER SHELF

© 2020 Copyright Eagle Industrial Group Inc.

US Patents D553,401 / 7,357,262 / D697,785 / 7,152,145. Other Patents Pending

Limited Lifetime Warranty

WARNING:This product can expose you to chemicals

including lead, which is know to the State of California to cause cancer and birth defect

or other reproductive harm. For more information, go to:

www.P65Warnings.ca.gov

SafeRacks® Garage ShelvingAssembly Instructions24”x92”x84” • 24”x72”x84 • 24”x48”x84

Components:

24” Side Rail (x8)

24” Center Support (x4)

84” Vertical Post (x4)

Wire Decking (x8)92” Side Rail (x8) or72” Side Rail (x8) or48” Side Rail (x8)

#10-24 Deck Clip Screw (x16)

#10-24 Shoulder Bolt (x64)

#10-24 Wingnut (x16)

#10-24 Hex Nut (x64) Wire Decking

Bracket (x8) 5/32” Allen Key (x1)

NOTE:If you purchase a 24” x 48” x 84” Garage Shelving unit, some of the components and steps will vary. The following are not included:-24” Center Support-#10-24 Deck Clip Screw-#10-24 Wingnut-Wire Decking Bracket-1/4”-20 Hex Bolt-1/4”-20 Hex Nut

Additionally, you will have only recieved 4 Wire Decking units. For further questions, please call 877-655-3443.

1/4”-20 Hex Nut (x16)

1/4”-20 Hex Bolt (x16) 3/8” Wrench

Assemble #10-24 Shoulder Bolts and #10-24 Hex Nuts using the top and bottom holes at the edges of all side rails..

After selecting desired height, position side rail such that the shoulder bolts pass through the “teardrop” holes in the vertical post. Ensure the lip of the side rail is facing inward and upward.

Using a Rubber Mallet, secure the shoulder bolts into the “teardrop” holes until the side rail is tight and secure.

Repeat the process for the 24” side rails. Ensure the lip of each side rail is facing inward and positioned at the top of the side rail.

Repeat until all four sides of the shelf frame are in place.

Position the center support between the two long side rails and align the with the center holes. Ensure the lipof the center support is positioned at the top. Secure the center support using four 1/4” Hex Bolts and1/4”-20 Hex Nuts. This step is not applicable for the 24” x 48” shelf.

SafeRacks® Garage ShelvingAssembly Instructions24”x92”x84” • 24”x72”x84 • 24”x48”x84

1. 2.

3. 4.

5. 6.

SafeRacks® Garage ShelvingAssembly Instructions24”x92”x84” • 24”x72”x84 • 24”x48”x84

Place wire decking units side by side onto the lips of the beams within each frame. NOTE: The 48” shelving uses a single wire decking unit placed longways.

7. 8.

9. 10.

IF YOU HAVE ANY QUESTIONS DURING YOUR INSTALLATION, PLEASE CALL

877-655-3443OR GO TO

www.SafeRacks.com

Repeat steps 1-6 until the whole frame of the rack is assembled.

Using the wire decking brackets, #10-24 Deck Clip Screws, and #10-24 Wingnuts, secure the wire decks for each level. This step is not applicable for the 24”x48” shelf.

Using a 5/32” allen key, check the tightness of all shoulder bolts to ensure the rack is sturdy and secure.