Upload
jorge-alberto-quiza-polania
View
2.166
Download
170
Embed Size (px)
Citation preview
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 1/86
Camco B Deflector Lug Conventional Gas Lift
Mandrel Features and Benefits
Typical Applications
1
12/06/00 BJR
• Standard API connections
and grades.
• Robust construction
• Accepts standard 1”
conventional gas lift valves
and checks.
• B deflector lug mandrels are
designed for dual-string
installations and are also
normally used in injection-pressure-operated tubing flow
applications. These mandrels
feature long, tapered lugs
welded in line with the exterior
ported lug to protect the installed
subsurface control device and
allow the material to easily pass
other mandrels during
installation in string applications
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 2/86
Camco B-1 Conventional Reverse Flow Check Valves
eatures and Benefits
ypical Applications
2
12/06/00 BJR
Integral reverse check
Includes hard and soft seats
Available in standard or premium
materials
Camco reverse flow check valves require flowto close. As the differential pressure across
the valve’s check dart increases, the dart
contacts the soft seat and then the hard seat
to form a seal and close the check valve.
These valves each have an elastomeric softseat and stainless steel hard seat. The initial
seal is between the valve’s stainless steel
check dart and the soft seat. These check
valves can withstand 10,000 psi differential
pressure and can be converted from velocity
check valves to positive check valves by the
addition of a spring. The flow area for the 1m“ OD B-1 valve is equivalent to a 5/16” port.
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 3/86
Camco BEK-2 and BEK-3 Latches eatures and Benefits
ypical Applications
3
12/06/00 BJR
Rugged field proven design
Ring type latch
Available in stainless steel or high
nickel alloys
The BEK Latch is installed and removed fromthe mandrel pocket using standard slickline
methods. A minimum amount of force is
required to install the latch. This is particularly
important in deviated wells where forceful
downward jarring is not possible.
The latch components are available in either
stainless steel or nickel alloys for corrosion
resistance in wells with high concentrations of
Hydrogen Sulfide and / or Carbon Dioxide.
The Camco BEK latch secures 1” OD side
pocket devices in Camco KB series side pocketmandrels. The latch is used when flow through
the latch is desired. The BEK-3 is used when
an erosion-resistant bore is desired.
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 4/86
Camco BK - 1 Injection Pressure Operated Gas Lift Va
eatures and Benefits
ypical Applications
4
12/06/00 BJR
Nitrogen charged bellows
Floating seat to promote positivestem/seat
Injection pressure operated
Dual seal nitrogen containment
Special bellows treatment to prolonglife
Available in various alloys and
elastomers
Integral reverse check
1/8” - 5/16” port sizes The bellows of the BK-1 gas lift valve is
constructed of three-ply Monel. During
manufacture, the bellows is subjected to a special
hydraulic forming process to seat all the
convolutions of the bellows so that each
convolution accepts an equal amount of stressduring valve operation.
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 5/86
Camco BK Infection Pressure Operated Gas Lift Valv
eatures and Benefits
ypical Applications
5
12/06/00 BJR
Nitrogen charged bellows
Floating seat to promote positive stem/seat
Injection pressure operated
Dual seal nitrogen containment
Special bellows treatment to prolong lift
Available in various alloys and elastomers
Integral reverse check
1/8” - 5/16” port sizes
The bellows of the BK gas lift valve is constructed
of three-ply Monel. During manufacture, the
bellows is placed in a hydrostatic pressure
chamber and subjected to external pressure. This
special hydraulic forming process seats all the
convolutions of the valve bellows so that each
convolution accepts an equal amount of stress
during valve operation. The component parts of
the bellows assembly are unitized by induction
brazing that enables the nitrogen charge to be
sealed in the bellows without the use of
elastomers.
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 6/86
Camco BK - 2 Latch eatures and Benefits
ypical Applications
6
12/06/00 BJR
Compact and simple design latch ring
design
Minimum amount of force to install in
deviated wells
Latch Components are made of premium
materials for stress cracking resistance
The BK - 2 Latch is installed and removed
from the side pocket mandrel using standard
slickline methods. A minimum amount of
force is required to install the latch. This is
particularly important in deviated wells where
forceful downward jarring is not possible.
Latch components are available in either
stainless steel or nickel alloys for corrosion
resistance in wells with high concentrations of
Hydrogen Sulfide and/or Carbon Dioxide.
The Camco BK-2 latch secures 1” OD gas liftvalves, chemical injection valves, and other
side pocket devices in KBM, KBMM, KBMG,
or KBTG series side pocket mandrels.
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 7/86
Camco BKCI-2 Chemical Injection Valve eatures and Benefits
ypical Applications
7
12/06/00 BJR
Valve constructed from stainless steel or
nickel alloys
Nitrogen charged dome operation
Various packing materials available
The BKCI-2 valve offers metal seal nitrogencontainment technology. Instead of the conventional
bellows type design, the BKCI-2 uses a two-way
metal seal piston for operation. Silicone fluid is
maintained above the piston and acts as a barrier
between the gas dome charge and sealing lips of the
piston, which enables the valve to maintain nitrogen
dome pressures to 10, 000psi.
Friction characteristics of the BKCI-2 are different
from those observed on bellows operated valves.
Once opening pressure is achieved, the piston will
travel to the fully open position and allow maximum
flow. Friction between the piston and housing actsas a buffer to help prevent valve chatter.
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 8/86
Camco BKEO Equalizing Orifice Valve eatures and Benefits
ypical Applications
8
12/06/00 BJR
Integral latch, prong and reverse check
Open porting for circulation after equalization
Wide selection of orifice sized (1/8” - 5/16”)
Available in various alloys and elastomers
The BKEO equalizing dummy valve is available
in stainless steel and high nickel alloys for use in
corrosive environment. Sealing materials are
utilized to allow the valve to be used in standard
to high temperature conditions.
The BKEO valve is installed in the mandrel either at the surface prior to running the completion or
by standard slickline methods after the mandrels
have been installed in the well. To equalize
pressure between the tubing and casing annulus
during pulling operations.
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 9/86
Camco BKF - 12 Production Pressure Operated Gas L
Valve Features and Benefits
ypical Applications
9
12/06/00 BJR
Externally adjusted spring
Cross-over seat design
Integral reverse check
Simple design, modular construction
Available in various alloys and elastomers
Unitized bellows nitrogen containment
Port sized 1/8” - 1/4”
The BKF-12 is bellows actuated, spring
loaded and and normally closed. The
valve components are available in either
stainless steel or nickel alloys for
corrosion resistance in wells with high
concentrations of Hydrogen Sulfide and/or
Carbon Dioxide. The metal used conformsto NACE standard MR0175 for sulfide
stress cracking resistant metallic materials.
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 10/86
Camco BKFS Circulating Valve
10
12/06/00 BJR
NTRODUCTION
The Camco* BKFS Circulating Valve is a 1” slickline
etrievable device which enables the operator to circulateuid through the pocket of a side pocket mandrel without
amage to the pocket. The valve consists of four housing
omponents, a valve nose and two sets of packing.
FEATURES
Large flow area
For circulation in either direction
Utilizes ported BEK-2 or BEK-3 type latch
Simple design, modular construction
Available in various alloys and elastomers
Optional choke sizes (1/16” - 7/16”)
APPLICATION AND OPERATION
Corrosion resistant materials are available for use in well
with high concentration of H2S and/or CO2. Various sealing
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 11/86
Camco BKLK-2 Chemical Injection Valve
11
12/06/00 BJR
NTRODUCTION
he Camco* BKLK-2 retrievable nitrogen charged chemical
jection valve controls chemicals injected into the
roduction fluid at valve depth. The 1” OD BKLK-2 ha
trogen charged Monel® bellows that maintains the valve
a normally closed position. The valves are available in
gh nickel and stainless steel construction to provide
orrosion resistance in wells with high concentrations of
2S or CO2.
EATURES
Port size options (1/8” – 3/16”)
Nitrogen charged bellows operation
Valve constructed from stainless steel or nickel alloy
Various packing materials available
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 12/86
Camco C Series Conventional Gas Lift Mandrels
12
12/06/00 BJR
NTRODUCTION
he Camco* C Series Conventional Gas Lift
Mandrels are installed as part of the tubing string
nd have an exterior ported lug which accepts a 1-
2” OD conventional subsurface control device and
reverse flow check valve. All C series mandrels
re internally drifted to standard drift specifications
nd hydrostatically tested to 6,000 psi.
EATURES
Standard API connections and grades
Robust construction
Accepts standard 1-1/2” conventional gas lift
valves and checks
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 13/86
Camco BKO-3 Gas Lift Orifice Valve
13
12/06/00 BJR
NTRODUCTION
The Camco* BKO-3 Orifice Valve is a 1" OD slickline
etrievable valve designed for use in continuous flow gas lift
nstallations. When installed in a KB series mandrel, the
BKO-3 is used to control the flow of gas from the casing
annulus to the tubing. When installed in a KB series
mandrel with the EC feature for annular lift, the BKO-3 valve
ontrols flow from the tubing to the casing. The valve
onsists of two primary housing components, a floating
eat, a check dart, a valve nose, and two sets of external
packing.
FEATURES
Simple design, modular construction
Available in various alloys
Many packing materials available
Wide selection of orifice sizes (1/8” - 5/16”)
Integral reverse check
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 14/86
Camco BKR-5 Production Pressure Operated Gas Lif
Valve
14
12/06/00 BJR
NTRODUCTION
The Camco* BKR-5 gas lift valve is a 1" OD slickline retrievable ga
ft valve that is production pressure operated and used in
ontinuous flow gas lift installations. The BKR-5 valve features an
ntegral bottom latch and is installed in KB series mandrels. The
roduction pressure sensitive BKR-5 is used to enhance production
y injecting high-pressure gas from the casing/tubing annulus, intohe production fluid. Carefully controlled quantities of gas lighten
he fluid column allowing natural reservoir pressure to push the
uid up the tubing.
FEATURES
Integral bottom latch
Simple design, modular construction
Available in various alloys
Many packing materials available
Unitized bellows nitrogen containment
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 15/86
Camco BKT-1 Injection Pressure Operated Gas Lift Va
15
12/06/00 BJR
NTRODUCTION
he Camco* BKT-1 Gas Lift Valve is a 1” OD slickline
etrievable valve designed with an integral bottom latch and
ideal for use in either continuous flow or intermittent flow
as lift installations. This valve is equipped with solid
ngsten carbide seats, high temperature/high pressure
acking and high temperature o-ring seals with back-ups.
EATURES
Solid tungsten carbide valve seat
Integral bottom latch and reverse check
Equipped with high temperature/high pressure seals
Unitized bellows nitrogen containment
1/8” - 3/8” port sizes
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 16/86
Camco BR Deflector Lug Conventional Gas Lift Mandr
16
12/06/00 BJR
NTRODUCTION
The Camco* BR Deflector Lug Conventional Gas Lift
Mandrels are installed as part of the tubing string and have
an exterior ported lug which accepts a 1” OD conventional
ubsurface control device and a reverse flow check valve.
All B series mandrels are internally drifted to standard
rifted specifications and hydrostatically tested to 6,000 psi.
FEATURES
Standard API connections and grades
Robust construction
APPLICATION AND OPERATION
BR deflector lug mandrels are designed for either single-
tring or dual-string installations and are normally used in
production-pressure-operated tubing flow applications.
These mandrels, like B deflector lug mandrels, feature long,
apered, welded-on lugs for use in dual-string installations.
The exterior ported lug on the BR deflector lug mandrels,
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 17/86
Camco C Deflector Lug Conventional Gas Lift Mandre
17
12/06/00 BJR
TRODUCTION
he Camco* C Deflector Lug Conventional Gas Lift
andrels are installed as part of the tubing string and have
n exterior ported lug which accepts a 1-1/2” O
onventional subsurface control device and a reverse flow
heck valve. All C series mandrels are internally drifted to
andard drifted specifications and hydrostatically tested to
000 psi.
EATURES
Standard API connections and grades
Robust construction
Accepts standard 1-1/2” conventional gas lift valve
and checks
PPLICATION AND OPERATION
deflector lug mandrels are designed for dual-string
stallations and are normally used in injection-pressure-
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 18/86
Camco Merla Spring Loaded C-31R Chemical Injectio
Valve
18
12/06/00 BJR
NTRODUCTION
he Camco-Merla* Spring Loaded C-31R chemical injection
alve is a 1-1/2” OD slickline retrievable device used to
ontrol subsurface corrosion in wells with high
oncentrations of H2S and/or CO2, or to eliminate paraffin,
alt and/or hydrate formation in the tubing string and flow
nes. The valve makes possible precise control of injectionolumes and treatment of well fluid at valve depth.
EATURES
Valve components constructed from stainless steel o
nickel alloys
Spring loaded operation
Various packing materials available
Standard 3/16” port
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 19/86
Camco CEV Equalizing Dummy Valve
19
12/06/00 BJR
NTRODUCTION
he Camco* CEV equalizing dummy valve is a 1-1/2” O
etrievable isolation and pressure equalizing tool. The valve
installed in the mandrel pocket prior to the installation of
as lift valves or other side pocket equipment. The valve
onsists of an integral top lock, two sets of packing, an
qualizing prong, a cylinder with two equalizing ports and a
alve nose. The CEV equalizing dummy is available in either
ainless steel or nickel alloys for corrosion resistance in
ells with high concentrations of H2S or CO2. Packing
aterials for the CEV valve are available for standard
ervice to high temperature service to suit individual wellonditions.
EATURES
Simple rugged design
Available in various alloys
Various packing material available
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 20/86
Camco CF Conventional Reverse Flow Check Valves
20
12/06/00 BJR
NTRODUCTION
he Camco* CF Conventional Reverse Flow Check Valves
re 1-1/2” velocity check valves used with Camco
onventional gas lift valves that do not have integral
everse flow check valves. These check valves protect the
asing from backflow through valves below the working
alve, allow application of pressure to the casing for
rculation or acidizing and prevent commingling of
roduction fluids in dual gas lift installations.
EATURES
Integral reverse check
Includes hard and soft seats
Available in standard or premium materials
PPLICATION AND OPERATION
amco reverse flow check valves require flow to close. As
e differential pressure across the valve’s check dart
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 21/86
Camco-Merla CM-30 R Spring Loaded Chemical Injecti
Valve
21
12/06/00 BJR
NTRODUCTION
he Camco-Merla* CM-30R Spring Loaded Chemical
njection Valve is a 1” OD slickline retrievable device used
o control subsurface corrosion in wells with high
oncentrations of H2S and/or CO2, or to eliminate paraffin,
alt and/or hydrate formation in the tubing string and flow
nes. The valve makes possible precise control of injection
olumes and treatment of well fluid at valve depth.
EATURES
Valve components constructed from stainless steel or
nickel alloys
Spring loaded operation
Various packing materials available
Standard 3/16” port
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 22/86
Camco CR Deflector Lug Conventional Gas Lift Mandr
22
12/06/00 BJR
NTRODUCTION
he Camco* CR Deflector Lug Conventional Gas Lift
andrels are installed as part of the tubing string and have
n exterior ported lug which accepts a 1-1/2” O
onventional subsurface control device and a reverse flow
heck valve. All C series mandrels are internally drifted to
andard drifted specifications and hydrostatically tested to
000 psi.
EATURES
Standard API connections and grades
Robust construction
Accepts standard 1-1/2” conventional gas lift valves
and checks
PPLICATION AND OPERATION
R deflector lug mandrels are designed for either single-
ring or dual-string installations and are normally used in
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 23/86
CSK - 1 Circulating Valve
23
12/06/00 BJR
NTRODUCTION
he CSK-1 Circulating Valve is a 1” slickline retrievable
evice, which enables the operator to circulate fluid
rough the pocket of a side pocket mandrel without
amage to the pocket. The valve consists of four housing
omponents, an integral bottom latch and two sets of
acking.
EATURES
Large flow area
For circulation in either direction
Integral bottom latch
Simple design, modular construction
Available in various alloys and elastomers
PPLICATION AND OPERATION
orrosion resistant materials are available for use in wells
ith high concentration of H2S and/or CO2. Various sealing
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 24/86
Camco DK - Dummy Valve
24
12/06/00 BJR
NTRODUCTION
he Camco* DK-1 dummy valve is a 1" OD slickline
etrievable non-equalizing dummy valve designed to be
stalled in a KB series side pocket mandrel. The dummy
onsists of a running head, a body, two packing sections,
nd an integral bottom collet latch. The major components
f the dummy valve are available in either high nickel alloys
r stainless steel for corrosion resistance in wells with high
oncentrations of H2S and/or CO2.
EATURES
Integral bottom latch
Rugged solid construction
Available in stainless steel or high nickel alloys
Various packing materials available
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 25/86
Camco DKO-2 Gas Lift Orifice Valve
25
12/06/00 BJR
NTRODUCTION
he Camco* DKO-2 Orifice Valve is a 1” OD slickline
etrievable valve designed for use in continuous flow gas lift
stallations. When installed in a KB Series mandrel, the
KO-2 is used to control the flow of gas from the casing
nnulus to the tubing. When installed in a KB Series
andrel with the EC feature for annular lift, the DKO-2 valve
ontrols flow from the tubing to the casing. The valve
onsists of a running head and two packing barrels, chec
ousing, a fixed orifice, an integral reverse flow check
ement, an integral bottom latch, and two sets of external
acking.
EATURES
Integral bottom latch and reverse check
Wide selection of orifice sizes (1/8” - 3/8”)
Convertible to casing flow operation
Available in various alloys and elastomers
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 26/86
Camco E Dummy Valve
26
12/06/00 BJR
NTRODUCTION
he Camco* E dummy valve is a 1" OD slickline retrievable
on-equalizing dummy valve designed to be installed in a
B series side pocket mandrel. The dummy consists of two
acking sections installed on two pieces of bar stock. The
ummy valve is threaded to accept a BK series top latch.
he valve is available in either high-nickel alloys or
ainless steel for corrosion resistance in wells with high
oncentrations of H2S and/or CO2.
EATURES
Rugged, solid construction
Available in stainless steel or high nickel alloys
Various packing materials available
Accepts top latch
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 27/86
Camco - Merla ED-30R Equalizing Dummy Valve
27
12/06/00 BJR
NTRODUCTION
he Camco-Merla* ED-30R Equalizing Dummy Valve is an 1-
2” valve designed to provide isolation of tubing and casing
ressure until it is desirable to retrieve the valve. These
alves feature an integral RK style latch and are compatible
ith any Camco M series side pocket mandrel with a
yle pocket. The valve features a prong which will shift
ownward during the retrieving operation to equalize
asing to tubing pressure. In addition, the valves open
orting allows fluids to be circulated after equalization has
ccurred.
EATURES
Integral latch
Open porting for circulation after equalization
Circulating area equivalent to 1/4" diameter
Available in various alloys and elastomers
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 28/86
Camco EK-1 Equalizing Dummy Valve
28
12/06/00 BJR
NTRODUCTION
he Camco* EK-1 equalizing dummy valve is a 1” O
etrievable isolation and pressure equalization tool. The
alve is installed in a Camco KB series side pocket mandrel
rior to the installation of gas lift valves or other side pocket
quipment. The EK-1 equalizing dummy valve is used to
qualize differential pressure between the tubing and
asing annulus at valve depth. The EK-1 equalizing dummy
alve is available in either stainless steel or nickel alloys for
orrosion resistance in wells with high concentrations of
2S and C02. Packing materials for the EK-1 valve are
vailable for standard to high temperature service to suitdividual well conditions.
EATURES
Simple, design modular construction
Integral bottom latch
Various packing materials available
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 29/86
Camco-Merla F-12R Waterflood Flow Regulator
29
12/06/00 BJR
NTRODUCTION
he Camco-Merla* 1-1/2” OD F-12R Waterflood Flow
egulator consists of a fixed calibrated orifice mounted on
spring-dampened stem, acting together as a variable
rifice. The calibrated orifice allows a predetermined water
ow to pass when a minimum pressure differential is
tained. When this minimum pressure differential is
ached, the spring is compressed, causing the variable
rifice to begin closing, thus maintaining a constant flow
ate independent of pressure variations.
EATURES
Rugged back check system**
Integral inlet filter
Rugged, solid construction
Available in stainless steel or high nickel alloys
Various packing materials available
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 30/86
Camco-Merla FM-14R Waterflood Flow Regulator
30
12/06/00 BJR
NTRODUCTION
he Camco-Merla* 1” OD FM-14R Waterflood Flow
egulator consists of a fixed calibrated orifice mounted on
spring-dampened stem, acting together as a variable
rifice. The calibrated orifice allows a predetermined water
ow to pass when a minimum pressure differential is
ttained. When this minimum pressure differential is
eached, the spring is compressed, causing the variable
rifice to begin closing, thus maintaining a constant flow
ate independent of pressure variations.
EATURES
Rugged back check system
Integral inlet filter
Rugged, solid construction
Available in stainless steel or high nickel alloys
Various packing materials available
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 31/86
Camco J-20 Conventional Reverse Flow Check Valve
31
12/06/00 BJR
NTRODUCTION
he Camco* J-20 Conventional Reverse Flow Check Valves
re 1-1/2” velocity check valves used with Camco
onventional gas lift valves that do not have integral
everse flow check valves. These check valves protect the
asing from backflow through valves below the working
alve, allow application of pressure to the tubing for
rculation or acidizing and prevent commingling of
roduction fluids in dual gas lift installations.
EATURES
Integral reverse check
Includes hard and soft seats
Available in standard or premium materials
PPLICATION AND OPERATION
amco reverse flow check valves require flow to close. As
e differential pressure across the valve’s check dart
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 32/86
Camco J-20 Injection Pressure Operated Gas Lift
Valve
32
12/06/00 BJR
NTRODUCTION
he Camco* J-20 Gas Lift Valve is a 1-1/2” OD conventional
as lift valve designed for use in either continuous flow or
termittent flow gas lift installations. The valve is bellows-
perated, nitrogen-charged and normally closed. The
mplicity of the J-20 design assures a long operating life.
EATURES
Conventional type valve
Nitrogen charged bellows
Floating seat to promote positive stem/seat
Injection pressure operated
Dual seat nitrogen containment
Special bellows treatment to prolong life
Available in various alloys and elastomers
3/16” – 1/2” port sizes
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 33/86
Camco J-40 Injection Pressure Operated Gas Lift Valv
33
12/06/00 BJR
NTRODUCTION
he Camco* J-40 Gas Lift Valve is a 1” OD conventional gas
t valve designed for use in either continuous flow or
termittent flow gas lift installations. The valve is bellows-
perated, nitrogen-charged and normally closed. The
mplicity of the J-40 design assures a long operating life.
EATURES
Conventional type valve
Nitrogen-charged bellows
Floating seat to promote positive stem/seat
Injection pressure operated
Dual seat nitrogen containment
Special bellows treatment to prolong life
Available in various alloys and elastomers
1/8” – 3/8” port sizes
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 34/86
Camco J-50 Macaroni Mandrel
34
12/06/00 BJR
TRODUCTION
he Camco* J-50 Macaroni Mandrel is installed on a
acaroni tubing string in a tubingless completion. The J-5
acaroni mandrel accepts 5/8 inch OD conventional
ubsurface control devices. These mandrels generally
ave a smaller OD than concave mandrels.
EATURES
Solid one-piece construction
Accepts 5/8” OD gas lift valve
Available in 1.315” – 2.875” sizes
Available with API or premium connections
PPLICATION AND OPERATION
amco macaroni mandrels provide a means to install
ubsurface control devices in tubingless completions.
ubingless completions are those in which two or more
acaroni tubing strings are installed in the wellbore and
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 35/86
Camco J-50 Injection Pressure Operated Gas Lift Valv
35
12/06/00 BJR
NTRODUCTION
he Camco*J-50 Gas Lift Valve is a 5/8” OD conventional
as lift valve. The valve is bellows-operated, nitrogen-
harged, and normally closed. The simplicity of the J-5
esign assures a long operating life.
EATURES
Conventional type valve
Nitrogen charged bellows
Floating seat to promote positive stem/seat
Injection pressure operated
Dual seat nitrogen containment
Special bellows treatment to prolong life
Integral reverse check
1/8” - 3/8” port sizes
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 36/86
Camco JR-20 Gas Lift Valve
36
12/06/00 BJR
NTRODUCTION
he Camco* JR-20 Gas Lift Valve is a 1-1/2” OD production
ressure operated conventional gas lift valve designed for
se in continuous flow gas lift installations. The valve is
ellows-actuated, nitrogen-charged and normally closed.
he simple design of the JR-20 valve assures a long
perating life.
EATURES
Crossover seat design
Unitized bellows nitrogen containment
Simple design, modular construction
Available in various alloys and elastomers
Port sizes 1/8” –1/4”
PPLICATION AND OPERATION
he bellows of the JR-20 Gas Lift Valve is constructed of
hree-ply Monel. During manufacture, the bellows is placed
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 37/86
Camco JR-40 Injection Pressure Operated Gas Lift Val
37
12/06/00 BJR
NTRODUCTION
he Camco* JR-40 Gas Lift Valve is a 1” OD production
ressure operated conventional gas lift valve designed for
se in continuos flow gas lift installations. The valve is
ellows-actuated, nitrogen-charged and normally closed.
he simple design of the JR-40 valve assures a long
perating life.
EATURES
Crossover seat design
Unitized bellows nitrogen containment
Simple design, modular construction
Available in various alloys and elastomers
Port sizes 1/8” – 3/16”
PPLICATION AND OPERATION
he bellows of the JR-40 Gas Lift Valve is constructed of
hree-ply Monel. During manufacture, the bellows is placed
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 38/86
Camco KBG Side Pocket Mandrel
38
12/06/00 BJR
NTRODUCTION
The Camco* KBG series side pocket mandrels are made up
as part of the tubing string when preparing a well for gas lift
production, chemical injection, waterflood, or other special
applications. These mandrels accept standard 1” top and
bottom latch equipment. The KBG series side pocket
mandrels are designed with a round cross section and are
available in a variety of tubing sizes and thread types.
FEATURES
Single 1” pocket round mandrel
Patented positioning sleeve orientation system
Smooth internal/external shoulders
Solid bar pocket and discriminator construction
Pressure rating approaches or equals that of tubing
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 39/86
Camco KBMG and KBUG Side Pocket Mandrel
39
12/06/00 BJR
TRODUCTION
he Camco* KBMG and KBUG series mandrels are made up
s part of the tubing string when preparing a well for gas lift
oduction, chemical injection, waterflood or other special
pplications. The KBMG series side pocket mandrels are
esigned with an oval cross section and are available in a
ariety of tubing sizes and thread types. The 3-1/2” size
andrel is designated KBUG, because it has a reduced
xternal geometry for use in dual string installations inside
5/8” - 47 PPF or lighter weight casing.
EATURES
Single 1” pocket oval mandrel
Forged oval pocket and tool discriminator
Patented positioning sleeve orientation system
Smooth internal and external surfaces
Integrally forged swages up through 3-1/2” size
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 40/86
Camco KBMM Side Pocket Mandrel
40
12/06/00 BJR
NTRODUCTION
he Camco* KBMM Series mandrels are made up as part of
e tubing string when preparing a well for gas lift
roduction, chemical injection, waterflood or other special
pplications. These side pocket mandrels are designed
ith an oval cross-section and are normally available only
box by box configuration for EUE type threads and box by
n for premium threads.
EATURES
Single 1" pocket oval mandrel
Smooth internal/external shoulders
Tubular pocket and integral tool discriminator
Patented positioning sleeve orienting system
Integrally forged swages through 3-1/2" size
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 41/86
Camco KBTG True-Guide Side Pocket Mandrel
41
12/06/00 BJR
NTRODUCTION
he Camco* KBTG TRUE-GUIDE* series side pocket
andrels are made up as part of the tubing string when
reparing a well for gas lift production, chemical injection,
aterflood, or other special applications. These mandrels
ccept standard 1” top and bottom latch equipment. The
BTG series side pocket mandrels are designed with a
und cross section and are available in a variety of tubing
zes and thread types.
EATURES
Single 1” pocket round mandrel
Patented positioning sleeve orientation system
Smooth internal/external shoulders
Solid bar pocket and discriminator construction
Pressure rating approaches or equals that of tubing
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 42/86
Camco-Merla LN-21R Proportional Response Valve
42
12/06/00 BJR
NTRODUCTION
he Camco-Merla* LN-21R is a 1-1/2” retrievable,
roportional response gas lift valve used for high gas
olume and high-pressure continuous flow gas lift
stallations. The proportional response of these valves
nable Schlumberger gas lift engineers to accurately
alculate the gas injection volumes required throughout the
ntire range of operating conditions of the well.
EATURES
Specialized bellows design
Combination spring and charged dome
Throttling type design
Hydrostatic and vibration protection for the bellows
Available in various alloys and elastomers
Port sizes 1/8” – 1/4"
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 43/86
Camco-Merla LNM-31R Proportional Response Valve
43
12/06/00 BJR
NTRODUCTION
he Camco-Merla* LNM-31R is a 1” retrievable,
roportional response gas lift valve used for high ga
olume and high-pressure continuous flow gas lift
stallations. The proportional response of these valve
nable gas lift engineers to accurately calculate the ga
jection volumes required throughout the entire range of
perating conditions of the well.
EATURES
Specialized bellows design
Combination spring and charged dome
Throttling type design
Hydrostatic and vibration protection for the bellows
Available in various alloys and elastomers
Port sizes 1/8” – 1/4"
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 44/86
Camco MMG Series Side Pocket Mandrel
44
12/06/00 BJR
NTRODUCTION
he Camco* MMG series mandrels are made up as part of
e tubing string when preparing a well for gas lift
roduction, chemical injection, waterflood or other special
pplications. The MMG series side pocket mandrels are
esigned with an oval cross section and are available in a
ariety of tubing sizes and thread types.
EATURES
Single 1-1/2” pocket oval mandrel
Forged oval pocket and tool discriminator
Patented positioning sleeve orientation system
Smooth internal and external surfaces
Integrally forged swages through 3-1/2” size
PPLICATION AND OPERATION
esigned with eccentric swages on both ends, these
andrels are available in a variety of thread types and
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 45/86
Camco MMGE Side Pocket Mandrel
45
12/06/00 BJR
NTRODUCTION
he Camco* MMGE side pocket mandrels are made up as
art of the tubing string when preparing a well for chamber
t applications. The MMGE series side pocket mandrels
re designed with an oval cross section and feature a 1-
2” bore pocket with a bottom snorkel to extend downward
to the casing. A 1/2” pipe connects the MMGE the top
acker in a chamber lift installation.
EATURES
Single 1-1/2” pocket oval mandrel
Patented positioning sleeve orientation system
Tool discriminator
Bottom snorkel on pocket
Pressure rating approaches or equals that of tubing
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 46/86
Camco MMGE-LTS Side Pocket Mandrel
46
12/06/00 BJR
NTRODUCTION
he Camco* MMGE-LTS Side Pocket Mandrels are made
p as part of the tubing string when preparing a well
hemical injection applications. The MMGE series side
ocket mandrels are designed with an oval cross section
nd feature a 1-1/2” bore pocket with a bottom snorkel to
xtend downward into the casing.
EATURES
Single 1-1/2” pocket oval mandrel
Patented positioning sleeve orientation system
Smooth internal/external shoulders
Integral injection line connection
Pressure rating approaches or equals that of tubing
PPLICATION AND OPERATION
he metallurgical properties of the steel used are closely
ontrolled through rigid specifications. The mandrels for
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 47/86
Camco MMG-LTS Side Pocket Mandrel
47
12/06/00 BJR
NTRODUCTION
he Camco* MMG-LTS Side Pocket Mandrels are made up
s part of the tubing string when preparing a well chemical
jection applications. The MMG series side pocket
andrels are designed with an oval cross section and
ature a 1-1/2” bore pocket.
EATURES
Single 1-1/2” pocket oval mandrel
Patented positioning sleeve orientation system
Smooth internal/external shoulders
Integral injection line connection
Pressure rating approaches or equals that of tubing
PPLICATION AND OPERATION
he metallurgical properties of the steel used are closely
ontrolled through rigid specifications. The mandrels for
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 48/86
Camco MMGW Waterflood Mandrel
48
12/06/00 BJR
NTRODUCTION
he Camco* MMGW series side pocket mandrels (Product
o. 05344-000-XXXXX) are single-pocket mandrels that
ccept 1-1/2” OD side pocket devices and incorporate all
e design features of the MMG series side pocket
andrels. The MMGW series side pocket mandrels are
vailable in a variety of tubing connection sizes and are
sed in single-string, multi-zone fluid injection/waterflood
stallations. These mandrels have a casing exhaust port at
e bottom of the side pocket, protecting the casing from
gh-velocity turbulence associated with the waterflood
rocess. A non-retrievable check valve is attached directly
the exhaust port to prevent backflow from the annulus to
e tubing through the empty pocket when the waterflood
ow regulator is removed.
EATURES
Single 1-1/2” pocket oval mandrel with smooth
internal and external surfaces
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 49/86
Camco MMM Side Pocket Mandrel
49
12/06/00 BJR
NTRODUCTION
he Camco* MMM Series mandrels are made up as part of
e tubing string when preparing a well for gas lift
roduction, chemical injection, waterflood or other special
pplications. These side pocket mandrels are designed
ith an oval cross-section and are normally available only
box by box configuration for EUE type threads and box by
n for premium threads.
EATURES
Single 1-1/2” pocket oval mandrel
Tubular pocket and tool discriminator
Patented positioning sleeve orientation system
Integrally forged swages through 3-1/2" size
Smooth internal/external shoulders
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 50/86
Camco MMRG Side Pocket Mandrel
50
12/06/00 BJR
NTRODUCTION
he Camco* MMRG series side pocket mandrels are made
p as part of the tubing string when preparing a well for gas
t production, chemical injection, waterflood, or other
pecial applications. The MMRG series side pocket
andrels are designed with a round cross section and are
vailable in a variety of tubing sizes and thread types.
EATURES
Single 1-1/2” pocket round mandrel
Patented positioning sleeve orientation system
Smooth internal/external shoulders
Solid bar pocket and discriminator construction
Pressure rating approaches or equals that of tubing
PPLICATION AND OPERATION
tandard Camco side pocket mandrels are manufactured
om high quality low alloy steel. The metallurgical
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 51/86
Camco MMRG-4-5 Side Pocket Mandrel
51
12/06/00 BJR
NTRODUCTION
he Camco* MMRG-4-5 Side Pocket Mandrel is made up as
art of the tubing string when completing a well for
pplications when casing-tubing connectivity is required
uch as in chemical injection, circulation, killing or gas lift.
he MMRG-4-5 series side pocket mandrel is designed with
round cross section, features a 1-1/2” bore pocket plus a
uardrail and control line protection system.
EATURES
Single 1-1/2” pocket round mandrel
Specially designed robust guard rail and control line
protection system
Extended swages for remachining of threads
Patented positioning sleeve orientation system
Smooth internal/external shoulders
Solid bar pocket and discriminator construction
Pressure rating approaches or equals that of tubing
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 52/86
Camco MMRG-5-LTS Side Pocket Mandrel
52
12/06/00 BJR
NTRODUCTION
he Camco* MMRG-5-LTS Side Pocket Mandrels are made
p as part of the tubing string when preparing a well for
hemical injection applications. The MMRG-5-LTS series
de pocket mandrels are designed with a round cross
ection, feature a 1-1/2” bore pocket plus a guard rail and
ontrol line protection system.
EATURES
Single 1-1/2” pocket round mandrel
Patented positioning sleeve orientation system
Smooth internal/external shoulders
Solid bar pocket and discriminator construction
Pressure rating approaches or equals that of tubing
Specially designed robust guard rail and control line
protection system
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 53/86
Camco MTG and MTA TRU-Guide Side Pocket Mandr
53
12/06/00 BJR
NTRODUCTION
he Camco* MTG and MTA TRU-GUIDE* series side pocket
mandrels are made up as part of the tubing string when
reparing a well for gas lift production, chemical injection
aterflood, or other special applications. The MTG and
MTA series side pocket mandrels are designed with a
ound cross section and are available in a variety of tubing
zes and thread sizes. MTG and MTA series mandrels
ave similar configurations. However, MTA series
mandrels feature a specially designed receiver pocket to
ccept Camco RA and RM latches.
EATURES
Single 1-1/2” pocket round mandrel
Patented positioning sleeve orientation system
Smooth internal/external shoulders
Insert pocket and discriminator
Pressure rating approaches or equals that of tubing
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 54/86
Camco-Merla Nova-10 Orifice Venturi Gas Lift Valve
54
12/06/00 BJR
NTRODUCTION
he 1” Camco-Merla* NOVA™ Series orifice venturi
perating valves replace valves with flat face orifices.
hese valves have an exclusive computer generated flow
rofile to promote a constant-flow gas injection rate. This
rofile induces maximum gas passage with minimal
fferential across the orifice venturi. This is achieved with
e same number of moving parts as a typical gas lift orifice
alve. The NOVA-10 is compatible with the BK series latch
nd will fit in any existing KB series side pocket mandrel.
EATURES
Made from hard, corrosion resistant materials
Provides expert gas lift design and support b
specialist
Provides focus on stabilization strategy and flo
stabilization by critical flow through injection point
Provides computer enhanced flow profiling
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 55/86
Camco-Merla Nova-15 Orifice Venturi Gas Lift Valve
55
12/06/00 BJR
NTRODUCTION
he 1-1/2” Camco-Merla* NOVA™ series orifice venturi
perating valves replace valves with flat face orifices.
hese valves have an exclusive computer generated flow
rofile to promote a constant-flow gas injection rate. This
rofile induces maximum gas passage with minimal
fferential across the orifice venturi. This is achieved with
e same number of moving parts as a typical gas lift orifice
alve. The NOVA-15 is compatible with the RK series and
M latches and will fit in any existing M series side pocket
andrel.
EATURES
Orifice venturi made from hard, corrosion resistant
materials
Body parts constructed from stainless steel or highnickel alloys
Various packing materials are available
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 56/86
Camco-Merla 0-21R Gas Lift Orifice Valve
56
12/06/00 BJR
NTRODUCTION
he Camco-Merla* O-21R Gas Lift Orifice Valve is a 1-
2” nominal OD, slickline retrievable valve that is designed
or use in continuous flow gas lift installations. When
stalled in a M series mandrel, the O-21R is used to control
e flow of gas from the casing annulus to the tubing. When
stalled in a M series mandrel with the EC feature for
nnular lift, the O-21R valve controls flow from the tubing to
e casing.
EATURES
Simple design, modular construction
Wide selection of orifice sizes (1/8” – 5/8”)
Integral spring loaded reverse check
Available in various alloys and elastomers
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 57/86
Camco-Merla 02-30R Gas Lift Orifice Valve
57
12/06/00 BJR
NTRODUCTION
he Camco-Merla* O2-30R Gas Lift Orifice Valve is a 1-
/2" OD slickline retrievable valve that is used to provide a
means of communication between the casing annulus and
ubing. The valve is installed in a Camco M Series side
ocket mandrel using an appropriate R Series latch and is
ormally closed. The design of the O2-30R orifice valve
cludes dual reverse checks.
EATURES
Dual spring loaded reverse checks
Simple design, modular construction
Available in various alloys and elastomers
Wide selection of orifice sizes (1/16” – 5/8”)
PPLICATION AND OPERATION
he O2-30R orifice valve is constructed from stainless steel
r nickel alloys for corrosion resistance in wells with high
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 58/86
Camco-Merla OM-21R Gas Lift Orifice Valve
58
12/06/00 BJR
NTRODUCTION
he Camco-Merla* OM-21R Gas Lift Orifice Valve is a 1”
ominal OD, slickline retrievable valve that is designed for
se in continuous flow gas lift installations. When installed
a KB series mandrel, the OM-21R is used to control the
ow of gas from the casing annulus to the tubing. When
stalled in a KB series mandrel with the EC feature for
nnular lift, the OM-21R valve controls flow from the tubing
the casing.
EATURES
Simple design, modular construction
Available in various alloys
Many packing materials available
Wide selection of orifice sizes (1/8” – 7/16”)
Integral reverse check
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 59/86
Camco PK-1 Pilot Operated Valve
59
12/06/00 BJR
TRODUCTION
he Camco* PK-1 Pilot Operated Valve is a 1” pilot operated
rge ported gas lift valve with integral bottom latch
esigned specifically for intermittent gas lift applications.
his design provides a large port for maximum gas injection
th a controlled spread for minimum gas consumption and
aximum surface control flexibility. The PK-1 valve is run in
B series side pocket mandrels.
EATURES
Large port for maximum efficiency
Adjustable tubing sensitivity
High slug lifting capacity
Preset spring compression
Port sizes 1/8” - 5/16”
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 60/86
Camco R-20-DC Injection Pressure Operated Gas Lif
Valve
60
12/06/00 BJR
NTRODUCTION
he Camco* R-20-DC gas lift valve is a 1-1/2” OD slickline
etrievable injection pressure operated gas lift valve
tilizing dual back checks designed for use in either
ontinuous flow or intermittent gas lift installations. The
alve is run on the appropriate R series latch in an M serie
de pocket mandrel.
EATURES
Nitrogen charged three-ply bellows
Floating seat to promote positive stem/seat alignmentInjection pressure operated
Dual back check system
Rugged, solid construction
Available in stainless steel or high nickel alloys
Various packing materials available
1/8” - 1/2” port sizes
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 61/86
Camco R-25P Gas Lift Valve
61
12/06/00 BJR
NTRODUCTION
he Camco* R-25P Gas Lift Valve is a 1-1/2" OD slickline
etrievable gas lift valve. The R-25P is production pressure
perated and is used in continuous flow gas lift
stallations. The production-pressure sensitive R-25
alve is used to enhance production by injecting high-
ressure gas from the casing/tubing annulus, into the
roduction fluid. Carefully controlled quantities of gas
ghten the fluid column allowing natural reservoir pressure
push the fluid up the tubing.
EATURES
Externally adjusted spring
Cross-over seat design
Integral reverse check
Simple design, modular construction
Available in various alloys and elastomers
Unitized bellows nitrogen containment
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 62/86
Camco RA Latch
62
12/06/00 BJR
NTRODUCTION
he Camco* RA latch is a 1-1/2” OD retrievable valve top
tch which anchors Camco retrievable gas lift valves and
de pocket accessories in the appropriate M series Camc
de pocket mandrels with an A-Type pocket. This latch i
esigned with a spring-loaded rotating latch cam.
EATURES
Rugged field proven design
Cam type latch
Available in stainless steel or high nickel alloys
PPLICATION AND OPERATION
he RA latch is installed and removed from the mandrel
ocket using standard slickline methods. A minimu
mount of force is required to install the latch.
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 63/86
Camco RCI-2 Chemical Injection Valve
63
12/06/00 BJR
NTRODUCTION
he Camco* RCI-2 chemical injection valve is a 1-1/2” O
ickline retrievable device used to inject chemicals to help
ontrol subsurface corrosion in wells with moderate to high
oncentration of H2S and/or CO2, or to eliminate paraffin,
alt and/or hydrate formation in the tubing string and flow
nes. The RCI-2 valve is designed for high pressure service
eyond the capabilities of standard bellows operated
hemical injection valves.
EATURES
Valve constructed from stainless steel or nickel alloys
Nitrogen charged bellows operation
Various packing materials available
PPLICATION AND OPERATION
he RCI-2 valve offers metal seal nitrogen containment
echnology. Instead of the conventional bellows type
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 64/86
Camco RCB Chemical Injection Valve
64
12/06/00 BJR
NTRODUCTION
he Camco* RCB retrievable nitrogen charged chemical
jection valve controls chemicals injected into the
roduction fluid at valve depth. The 1 1/2” OD RCB has
trogen charged three-ply Monel® bellows that maintains
e valve in a normally closed position. The valves are
vailable in high nickel and stainless steel construction to
rovides corrosion resistance in wells with high
oncentrations of H2S or CO2.
EATURES
Valve constructed from stainless steel or nickel alloys
Nitrogen charged bellows operation
Various packing materials available
PPLICATION AND OPERATION
he bellows of the RCB chemical injection valve is
onstructed of three-ply Monel® and is designed and
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 65/86
Camco RCDC Chemical Injection Valve
65
12/06/00 BJR
NTRODUCTION
he Camco* RCDC chemical injection valve is a 1-1/2” O
ickline retrievable device used to control subsurface
orrosion in wells with high concentrations of H2S and/or
O2, or to eliminate paraffin, salt and/or hydrate formation
the tubing string and flow lines. The valve makes
ossible control of injection volumes and treatment of well
uid at valve depth.
EATURES
Modular design, rugged, solid construction
Available in stainless steel or high nickel alloys
Various packing materials available
Dual, spring-loaded positive check
PPLICATION AND OPERATION
he RCDC chemical injection valve is a fully open valve with
wo spring loaded positive checks. Injection flow and fluid
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 66/86
Camco RD Dummy Valve
66
12/06/00 BJR
NTRODUCTION
The Camco* RD dummy valve is a 1-1/2" OD slickline
etrievable non-equalizing dummy valve designed to be
stalled in a M series side pocket mandrel. The dummy
onsists of two packing sections installed on two pieces of
ar stock. The dummy valve is threaded to accept an
eries top latch. The valve is available in either high-nickel
loys or stainless steel for corrosion resistance in wells
ith high concentrations of H2S and/or CO2.
acking materials for the RD dummy are available for
andard or high-temperature service to suit individual well
onditions. The simple design of the dummy valve allowsr easy replacement of the packing and for rapid low-cost
eplacement of components. The valve's rugged, solid
onstruction and quality materials provide a long service
e.
EATURES
Rugged solid construction
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 67/86
Camco RDO-5 Gas Lift Orifice
67
12/06/00 BJR
NTRODUCTION
he Camco* RDO-5 Orifice Valve is a 1-1/2” OD slickline
etrievable valve designed for use in continuous flow gas lift
stallations. When installed in an M series mandrel, the
DO-5 is used to control the flow of gas from the casing
nnulus to the tubing. When installed in an M series
mandrel with the EC feature for annular lift, the RDO-5 valve
ontrols flow from the tubing to the casing. The valve
onsists of two primary housing components, a floating
eat, an integral reverse flow check element, a valve nose
nd two sets of external packing.
EATURES
Simple design, modular construction
Available in various alloys
Many packing materials available
Wide selection of orifice sizes (3/16” - 3/4”)
Integral reverse check
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 68/86
Camco RG-2 Circulating Valve
68
12/06/00 BJR
TRODUCTION
he Camco* RG-2 Circulating Valve is a 1-1/2” OD
trievable device which enables the operator to circulate
id through the pocket of a mandrel without damage to the
ocket. The valve consists of three primary housing
mponents, a ported valve seat, two integral reverse flow
heck darts, a valve nose and two sets of external packing.
EATURES
Annulus to tubing circulation
Circulates out top and bottom
Large flow area (0.392 sq. in.)
Integral reverse checks
PPLICATION AND OPERATION
he RG-2 circulating valve with RKP latch is installed in a
andrel prior to circulation. The RG-2 valve has a flow area
quivalent to a 45/64” port. The special design through both
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 69/86
Camco RGR-2 Circulating Valve
69
12/06/00 BJR
NTRODUCTION
he Camco* RGR-2 Circulating Valve is a 1-1/2” retrievable
evice to allow circulation of fluid through the pocket of a
andrel without damage to the pocket. The valve consists
f four primary housing components, a ported housing
ection, two integral reverse flow check darts, a valve nose
nd two sets of external packing.
EATURES
Tubing to annulus circulation
Circulates through top and bottom
Large flow area
Integral reverse checks
PPLICATION AND OPERATION
he RGR-2 with the RKP latch is installed in the mandrel
rior to circulation. The RGR-2 has a flow area equivalent
o a 45/64” port. The special design of the RGR-2 valve
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 70/86
Camco 1-1/2” RIPC Injection Pressure Closed Gas Li
Valve
70
12/06/00 BJR
NTRODUCTION
he Camco* RIPC is a 1-1/2” OD slickline retrievable valve
esigned for use in continuous flow gas lift installations.
he valve is run on the appropriate Camco R Series latch in
Camco M Series side pocket mandrel.
EATURES
Rugged, solid construction
Available in stainless steel or high nickel alloys
Various packing materials available
Port sizes to 3/8”
PPLICATION AND OPERATION
he RIPC valve can be equipped with a floating seat
orifice) to 3/8” port size.
he bellows of the RIPC gas lift valve is constructed of three
y Monel. During manufacture, the bellows is placed in a
ydrostatic pressure chamber and subjected to external
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 71/86
Camco RK Latch
71
12/06/00 BJR
NTRODUCTION
he Camco* RK latch is a 1-1/2” OD, spring loaded, ring-
yle latch that anchors Camco retrievable gas lift valves
nd side pocket accessories in the appropriate Camco M
eries mandrels.
EATURES
Compact and simple latch ring design
Minimum amount of force to install in deviated wells
Latch components are made of premium materials for
stress cracking resistance
Pocket debris barrier
PPLICATION AND OPERATION
he RK latch is installed and removed from the side pocket
andrel using standard slickline methods. A minimu
mount of force is required to install the latch. This is
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 72/86
Camco RKEO Equalizing Dummy Valve
72
12/06/00 BJR
NTRODUCTION
he Camco* RKEO Equalizing Dummy Valve is an 1-1/2”
alve designed to provide isolation of tubing and casing
ressure until it is desirable to retrieve the valve. These
alves feature an integral RK style latch and are compatible
ith any Camco M series side pocket mandrel with a
yle pocket. The valve features a prong which will shift
ownward during the retrieving operation to equalize
asing to tubing pressure. In addition, the valves open
orting allows fluids to be circulated after equalization has
ccurred.
EATURES
Integral latch
Open porting for circulation after equalization
Available in various alloys and elastomers
Port sizes 5/16” - 1/2”
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 73/86
Camco RKP Latch
73
12/06/00 BJR
TRODUCTION
he Camco* RKP latch is a 1-1/2” OD spring loaded, ring-
yle latch which anchors Camco retrievable shear valves
circulating valves in the appropriate Camco MMM,
MG, MTG or MMRG Series mandrels. The RKP latch is
esigned to allow flow through the running head. The RK
tch is used when flow through the latch is desirable; such
s, in circulating or shear valve applications.
EATURES
Compact and simple ring type design
Minimum amount of force is necessary to install
Latch components are made from stainless steel or
high nickel alloys
PPLICATION AND OPERATION
he RKP latch is installed and removed from the mandrel
ocket using standard slickline methods. A minimum
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 74/86
Camco-Merla RM Latch
74
12/06/00 BJR
TRODUCTION
he Camco-Merla* RM latch is a 1-1/2” OD spring loaded,
og-style latch that anchors Camco retrievable gas lift
alves and side pocket accessories in the appropriate
amco MMA, MMARG or MTA mandrels. The RM latch
atures an o-ring on the latch stop which provides a debris
arrier in the top of the mandrel pocket.
EATURES
Compact and simple dog type design
Minimum amount of force is necessary to install
Latch components are made from stainless steel or
high nickel alloys
PPLICATION AND OPERATION
he RM latch is installed and removed from the side pocket
andrel using standard slickline methods. A minimum
mount of force is required to install the latch. This is
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 75/86
Camco-Merla RMP Latch
75
12/06/00 BJR
NTRODUCTION
he Camco-Merla* RMP latch is a 1-1/2” OD spring loaded,
og-style latch that anchors Camco retrievable gas lift
alves and side pocket accessories in the appropriate
amco MMARG, MTA or MMA type mandrels. The RM
tch features an o-ring on the latch stop which provides a
ebris barrier in the top of the mandrel pocket.
EATURES
Compact and simple dog type design
Minimum amount of force is necessary to install
Latch components are made from stainless steel or
high nickel alloys
PPLICATION AND OPERATION
he RMP latch is installed and removed from the side
ocket mandrel using standard slickline methods. A
inimum amount of force is required to install the latch.
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 76/86
Camco RP-6 Pilot Operated Valve
76
12/06/00 BJR
NTRODUCTION
he Camco* RP-6 is a 1-1/2” pilot operated, large ported
as lift valve designed specifically for intermittent gas lift
pplications. This design provides a large port for maximu
as consumption with a controlled spread for minimum gas
onsumption and maximum surface control flexibility. The
RP-6 valve is run with the appropriate R series latch in M
eries side pocket mandrels.
EATURES
Large port for maximum efficiency
Adjustable tubing sensitivity
High slug lifting capacity
Preset spring compression
Available in various alloys and elastomers
Port sizes 1/4" – 1/2"
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 77/86
Camco RS-6 Injection Pressure Operated Valve
77
12/06/00 BJR
NTRODUCTION
he Camco* RS-6 1-1/2” OD slickline retrievable production
ressure operated gas lift valve used in continuous flow
perations. The injection pressure sensitive RS-6 valve
sued to enhance production by injecting high pressure
as from the casing/tubing annulus into the production fluid.
arefully controlled quantities of gas lighten the fluidolumn allowing natural reservoir to push the fluid up the
bing.
EATURES
Simple rugged design
Spring loaded valve
Field proven operation
Integral reverse check
1/8” - 3/8” port sizes
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 78/86
Camco-Merla RV-15R Production Pressure Operated
Valve
78
12/06/00 BJR
NTRODUCTION
he Camco-Merla* RV-15R is a 1-1/2” retrievable
roduction pressure operated gas lift valve used in
ontinuous flow operations. The RV-15R is run on the
ppropriate R series latch in a M series side pocket
mandrel. These valves are particularly suited to deep, high
owing pressure gas lift wells, dual installations and in
ompletions with fluctuating injection pressures. The RV-
5R uses internal orifices to control maximum gas passage.
EATURES
Spring loaded, bellows actuated
Throttling type closure
Liquid-charged Monel® bellows
Port sizes 1/8” - 1/4"
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 79/86
Camco-Merla RVM-16R Production Pressure Operate
Valve
79
12/06/00 BJR
NTRODUCTION
he Camco-Merla* RVM-16R is a 1” retrievable production
ressure operated gas lift valve used in continuous flow
perations. The RVM-16R is run on the appropriate B
eries latch in a KB series side pocket mandrel. These
alves are particularly suited to deep, high flowing pressure
as lift wells, dual installations and in completions with
uctuating injection pressures. The RVM-16R uses internal
rifices to control maximum gas passage.
EATURES
Spring loaded, bellows actuated
Throttling type closure
Liquid-charged Monel® bellows
Available in various alloys and elastomers
Port sizes 1/8” - 1/4"
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 80/86
Camco RW Flow Regulator
80
12/06/00 BJR
NTRODUCTION
he Camco* RW 1-1/2” OD waterflood flow regulator was
eveloped to control the flow in water injection
stallations. The RW flow regulator and appropriate
eries latch is run in the M series side pocket mandrel.
amco has adapted the Waterman flow regulator principle
subsurface equipment to allow control of the quantity of
uid entering a single- or a multiple-zone water injection
ystem.
EATURES
Simple rugged design
Field proven operation
Available in various alloys
Various packing material available
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 81/86
Camco RWW Flow Regulator
81
12/06/00 BJR
NTRODUCTION
he Camco* RWW 1-1/2” OD flow regulator was developed
o control flow in water injection installations. The RW
ow regulator and appropriate R series latch is run in the M
eries side pocket mandrel. Camco adapted the Waterman
ow Regulator for subsurface equipment to allow control of
e quantity of fluid entering a single- or a multiple-zone
ater injection system.
EATURES
Various port sizes (1/8” - 3/8”)
Simple rugged design
Field proven operation
Available in various alloys and elastomers
PPLICATION AND OPERATION
he RWW flow regulator will maintain a predetermined and
reset flow rate regardless of changes in pressure
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 82/86
Camco S-16R Shear Relief Valve
82
12/06/00 BJR
NTRODUCTION
he Camco-Merla* S-16R 1-1/2” OD Shear Valve provides a
elective means of communication between casing and the
bing. This valve is activated by differential pressure. The
-16R is run on the appropriate R series latch in an M series
de pocket mandrel. The valve, which initially acts as a
ummy valve, has a piston that seals off the circulating
orts in the valve and the side pocket mandrel. The piston
held in the closed position with a tension bar. The shear
ameter of the tension bar determines the casing-to-tubing
ressure differential required to open the valve.
EATURES
Large 3/4" port size
Use of stainless steel or nickel alloys
Tension bar design
Predetermined differential pressure for tension bar
separation
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 83/86
Camco-Merla SM-14R Shear Relief Valve
83
12/06/00 BJR
NTRODUCTION
he Camco-Merla* SM-14R retrievable shear relief valve i
1” OD slickline retrievable valve that provides a selective
means of communication between casing and the tubing.
his valve is activated by differential pressure. The SM-14
run on the appropriate BK series or M latch in a KB serie
de pocket mandrel. The valve, which initially acts as aummy valve, has a piston that seals off the circulating
orts in the valve and the side pocket mandrel. The piston
held in the closed position with a tension bar. The shear
ameter of the tension bar determines the casing-to-tubing
ressure differential required to open the valve.
EATURES
Wide range of orifice sizes (1/8” - 7/16”)
Tension bar design
Predetermined differential predictable response t
pressure separation
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 84/86
Camco-Merla SO2M-14R Shear Orifice Valve
84
12/06/00 BJR
NTRODUCTION
he Camco-Merla* SO2-30R Shear Orifice Valve is a 1-
2” OD slickline retrievable valve used to provide a means
f communication between the casing annulus and tubing.
he valve is installed in a Camco M series side pocket
andrel using an appropriate R series latch and is normally
osed. The design of the SO2-30R orifice valve includes a
ovable piston, which is held in place by a tension bar.
EATURES
Dual spring loaded reverse checks
Available in numerous tension values
Wide choice of orifice sizes (1/8” – 5/8”)
Various packing and seal materials available
Available in stainless steel or high nickel alloys
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 85/86
Camco-Merla WF-14R Pilot Operated Valve
85
12/06/00 BJR
NTRODUCTION
he Camco-Merla* WF-14R is a 1-1/2” pilot operated, large
orted gas lift valve designed specifically for intermittent
as lift applications. This design provides a large port for
aximum gas consumption with a controlled spread for
inimum gas consumption and maximum surface control
exibility. The WF-14R valve is run with the appropriate
eries latch in M series side pocket mandrels.
EATURES
Large port for maximum efficiency
Adjustable tubing sensitivity
High slug lifting capacity
Preset spring compression
Available in various alloys and elastomers
7/14/2019 Gas Lift Camco Manual
http://slidepdf.com/reader/full/gas-lift-camco-manual 86/86
Camco-Merla WFM-14R Pilot Operated Valve
NTRODUCTION
he Camco-Merla* WFM-14R is a 1 ” pilot operated large
orted gas lift valve designed specifically for intermittent
as lift applications. This design provides a large port for
maximum gas consumption with a controlled spread for
minimum gas consumption and maximum surface control
exibility. The WFM-14R valve is run with the appropriate
K or M series latch in KB series side pocket mandrels.
EATURES
Large port for maximum efficiency
Adjustable tubing sensitivity
High slug lifting capacity
Preset spring compression
Available in various alloys and elastomers