Embed Size (px)
Citation preview
Select Start
Reaction starts: the green LED of the section lights up
Test time
Reaction ends: the green LED flashes
Remove the strip(s) and SPR(s) of the sectionResults print out automatically
Interpretation and measurement range
HOW TO PERFORM MAINTENANCE?
Weekly: - cleaning of the SPR blocks
Monthly: - cleaning of the reagent strip area- performing VIDAS QCV test- cleaning of the two optical lenses
02-1
0 /
008G
B990
71C
/ Th
is d
ocum
ent i
s no
t leg
ally
bin
ding
. bio
Mér
ieux
rese
rves
the
right
to m
odify
spe
cific
atio
ns w
ithou
t not
ice
/ BI
OM
ERIE
UX
and
the
blue
logo
, are
regi
ster
ed a
nd p
rote
cted
trad
emar
ksbe
long
ing
to b
ioM
érie
ux S
.A. o
r one
of i
ts s
ubsi
diar
ies
/ bi
oMér
ieux
SA
RCS
Lyon
673
620
399
/ P
rinte
d in
Fra
nce
/ TH
ERA
Con
seil
/ RC
S Ly
on B
398
160
242
If required, select User ID, if not press
q
SEEPACKAGE
INSERT
SEEPACKAGE
INSERT
bioMérieux S.A.69280 Marcy l’EtoileFranceTel.: 33 (0)4 78 87 20 00Fax: 33 (0)4 78 87 20 90www.biomerieux.com
SEE
MINI VIDAS
USER
MANUAL
SEE LENS
CLEANER
PACKAGE
INSERT
GCS / IMMUNOASSAYSSIMPLIFIED USER GUIDE
mini VIDAS®
2010/02/01
HOW TO KNOW IF A CALIBRATION IS VALID?
To do this, proceed as follows:
Press until the MAIN MENU is displayed
Select the test code in the list by pressing on the key to scroll down/up if necessary
Test code
● If the lot does not feature in the list, the lot has not been calibrated:
Press three times to return to the MAIN MENU
and follow the protocol on page 4
● If the lot features in the list, check whether the calibrationis still valid:
Press on the key corresponding to the lot required, and the following screen will be displayed:
Control the lot expiration date displayed on the screen
● If the calibration has expired:
Press three times to return to the MAIN MENU
and follow the protocol on page 5
● If the calibration is still valid:
Press three times to return to the MAIN MENU and follow the protocol on page 6
HOW TO UPDATE A PROTOCOL?Always read the protocole barcode before reading the MLE card
MAIN MENU
Select the Utility Menu
Select the Master lot menu
Select List Stored Stds
● If the test does not feature in the list, the test has not been calibrated:
Press twice to return to the MAIN MENU
and follow the protocol on page 4
● If the test features in the list, check whether the calibration isstill valid:
Select the lot if necessarySelect Assay Update
q q
q
q
q
q
SEEPACKAGE
INSERT
2 3
!IMPORTANT: The key enables the user to return to the MAIN MENU at any time.
Fulfil the warning instructions and click on Yes to continue
Read the protocole barcode printed on last page of the package insert with the barcode wand
Select Confirm to Quit
HOW TO READ A MLE CARD?
MAIN MENU
Selectthe Master Lot Menu
Place the MLE card on the white plastic card support
Slide the card support into an empty section
Select Read Master Lot
Select the chosen section
The message “Please wait”is displayed on the screen
As soon as the message disappears,remove the card and support
Press to return to the MAIN MENU
Then calibrate using the protocol below
HOW TO RUN STANDARDS (S) AND CONTROLS (C) FOR CALIBRATION?
If an error is made when selecting a standard, control or sample:
• select the position n° to be modified (1 to 6)• select “Assay”• select “Clear”
• select “Clear this position’s setup only”
MAIN MENU
Select Status Screen
Type 1
Repeat this operation for each standardused for the test
Select section A or B
Select S for the standard, type 1, then press
q
q
q
q
q
SEEPACKAGE
INSERT
4 5
!
Select C for control, type 1 for C1then press
Repeat this operation for each control used for the test
Then follow the protocol below from
HOW TO IDENTIFY SAMPLES IN STATUS SCREEN?
MAIN MENU
Select Status Screen
Type 1 *
Enter the Sample ID (see below) and, if necessary,the dilution factor
Press
After identifying the last patient, press until the work list for the section is displayed, then start running the samples using the protocol below
Sample identification(maximum of 12 alphanumeric characters)
Numeric characters are entered using the keyboardAlphabetic characters are entered by selecting each character on the screen:
Use the arrow pad on the keyboard to move the cursor and select the characters, then validate them one by one by pressing
Sample ID can also be entered by using the barcode wand
HOW TO RUN SAMPLES?
If required, leave reagents 30 min at room temperature before use
Check the type of sample and pre-process samples if required
Place the strip(s) and SPR(s) into the section indicated on the screen
Dispense the sample volume into the sample well of the strip
Repeat the same actions for each sample
*
Select a free section
Select Sample ID
q
q q
q
q
SEEPACKAGE
INSERT
IMPORTANT: The key enables the user to return to the Main Menu at any time.
SEEPACKAGE
INSERT
6 7
Select Start
Reaction starts: the green LED of the section lights up
Test time
Reaction ends: the green LED flashes
Remove the strip(s) and SPR(s) of the sectionResults print out automatically
Interpretation and measurement range
HOW TO PERFORM MAINTENANCE?
Weekly: - cleaning of the SPR blocks
Monthly: - cleaning of the reagent strip area- performing VIDAS QCV test- cleaning of the two optical lenses
02-1
0 /
008G
B990
71C
/ Th
is d
ocum
ent i
s no
t leg
ally
bin
ding
. bio
Mér
ieux
rese
rves
the
right
to m
odify
spe
cific
atio
ns w
ithou
t not
ice
/ BI
OM
ERIE
UX
and
the
blue
logo
, are
regi
ster
ed a
nd p
rote
cted
trad
emar
ksbe
long
ing
to b
ioM
érie
ux S
.A. o
r one
of i
ts s
ubsi
diar
ies
/ bi
oMér
ieux
SA
RCS
Lyon
673
620
399
/ P
rinte
d in
Fra
nce
/ TH
ERA
Con
seil
/ RC
S Ly
on B
398
160
242
If required, select User ID, if not press
q
SEEPACKAGE
INSERT
SEEPACKAGE
INSERT
bioMérieux S.A.69280 Marcy l’EtoileFranceTel.: 33 (0)4 78 87 20 00Fax: 33 (0)4 78 87 20 90www.biomerieux.com
SEE
MINI VIDAS
USER
MANUAL
SEE LENS
CLEANER
PACKAGE
INSERT
GCS / IMMUNOASSAYSSIMPLIFIED USER GUIDE
mini VIDAS®
2010/02/01
