Upload
others
View
8
Download
0
Embed Size (px)
Citation preview
Gen II Heaterwith Defrost
506101
906101 REV C 3/3/14, INST. GEN II HEATER KIT with DEFROST PG 1 OF 8
an ISO 9001:2008 Registered Company
18865 Goll St. San Antonio, TX 78266 ph: 210-654-7171 fax: 210-654-3113
2906101 REV C 3/3/14, INST. GEN II HEATER KIT with DEFROST PG 2 OF 8
Table of Contents1. Cover2. Table of Contents3. Packing List/Parts Disclaimer4. Heater Installation Figure 15. Heater Hose & Heater Control Valve Installation Figure 26. Defrost Duct Installation & Control Panel Operation Figures 3 & 47. Wiring Diagram8. Packing List
3906101 REV C 3/3/14, INST. GEN II HEATER KIT with DEFROST PG 3 OF 8
1
3
5
2
4
Packing List:Gen II Heater Kit with Defrost (506101)
No. Qty. Part No. Description
1.2.3.4.5.
11115
506601479000633810-VUA63360106200-VUE
Gen II Heater with Defrost Sub CaseGen II Heater with Defrost Wiring KitUniversal Defrost Duct KitGen II Heater with Defrost Installation Kit2” Duct Hose Per Foot
** Before beginning installation, open all packages and check contents of shipment. Please report any shortages directly to Vintage Air within 15 days. After 15 days, Vintage Air will not be responsible for missing or damaged items.
4906101 REV C 3/3/14, INST. GEN II HEATER KIT with DEFROST PG 4 OF 8
Firewall
1/4-20 x 1”Coarse Bolt 1/4-20 Hex Nut
with Star Washer
1/4 x 3/4”Flat Washer
Heater Installation1. Use heater unit as a template and drill (4) 9/32” diameter mounting holes as shown in Figure 1, below. NOTE: The Vintage Air heater unit is designed to mount inside of the firewall in the passenger compartment. The installation of the unit varies according to body manufacturer or modifications to original firewall. After selecting location, be sure unit does not interfere with cowl vent, wipers, etc.
Top of Windshield
Bottom Edge of DashDrill (4) 9/32”
DiameterMounting Holes
Figure 1
5906101 REV C 3/3/14, INST. GEN II HEATER KIT with DEFROST PG 5 OF 8
Route a piece of heater hose from the water pump to the top heater fitting of the heater core as shown inFigure 2, below. Secure using hose clamps.Route a piece of heater hose from the intake to the bottom heater fitting of the heater core as shown in Figure 2,below. NOTE: Install heater control valve inline with the intake manifold (pressure side) heater hose,and secure using hose clamps as shown in Figure 2, below. Also note proper flow direction.Fill radiator with coolant. Check all heater connections for leaks.Start engine and run until normal operating temperature is reached. Place switch in heat position (See Figure 4,Page 6) and select fan speed desired. The system will heat the vehicle.When valve is closed, inlet side of valve should be hot and outlet side should be cool. When valve is open, bothinlet and outlet side should be hot.
1.
2.
3.4.
5.
Heater with DefrostUnit
Clamps
Clamps
HeaterControlValve
Grommets
Heater Hose &Heater Control Valve Installation
NOTE: Vintage Air systems require (2) 5/8 hose nipples (not supplied). One for the intake (pressure)and one for the water pump (suction). If required, remove existing hose nipple or nipples and installnew 5/8 hose nipples in intake and water pump.
Figure 2
FROM INTAKEMANIFOLD
HOSECLAMPS
HEATERHOSE
FROM EVAPORATOR
TO WATER PUMP
FROM HEATER CONTROL VALVETO EVAPORATOR
6906101 REV C 3/3/14, INST. GEN II HEATER KIT with DEFROST PG 6 OF 8
BlowerSwitch
TemperatureControlSwitch
ModeSwitch
HI
MED
LO OFF
H
1/4”Dash
5”
Defrost Duct InstallationInstall the defrost ducts as shown in Figure 3, below. NOTE: Figure 3 shows general locations of defrosterducts. The location of these ducts will vary.
1.
Control Panel OperationBlower Switch: Located on the left and controls 3-speed fan motor.
Mode Switch: Located in the center, full counter clockwise is the first position and considered off if the bloweris not turned on. The first position activates the Bi-level mode and directs air to both defrost and floor levels.The second position activates the floor mode. The heater door opens and directs air to exit at floor level. Thethird position activates the defrost mode and will direct air to the defrost vents.
Temperature Control Switch: Located on the right, this allows you to adjust the temperature of the heatrunning through the system. For hotter temperatures, turn the switch clockwise and counterclockwise to reducethe temperature.
1.
2.
3.
Figure 3
Figure 4
7906101 REV C 3/3/14, INST. GEN II HEATER KIT with DEFROST PG 7 OF 8
L
C
M
B
H
LB
H
Orange
AUX. BAT.
Red
Red/WhiteRed/White
Grey/BlackGrey/BlackWhite/YellowWhite/Yellow
Wiring Diagram: Gen II Heater
Note Orientationof Plugs
Control Module
Heater ControlValve
Potentiometer
ModeSwitch
FanSpeedSwitch
BlowerMotor
30 AmpCircuit Breaker
To Battery orBattery Terminal
on Starter Solenoid.
WhiteGround
Black
Ground
White
Pink
Blu
eBla
ckO
range
Bro
wn
Light
Blu
e
Bla
ck/W
hite
White/
Ora
nge
White/
Blu
eW
hite/
Bro
wn
White/
Red
Red
Yello
w
Yellow
Floor/DefrostServo
(Rear View of Plug)
Heater ControlValve Servo
(Rear View of Plug)
906101 REV C 3/3/14, INST. GEN II HEATER KIT with DEFROST PG 8 OF 8
1
3
5
2
4
Packing List:Gen II Heater Kit with Defrost (506101)
No. Qty. Part No. Description
1.2.3.4.5.
11115
506601479000633810-VUA63360106200-VUE
Checked By:Packed By:
Date:
Gen II Heater with Defrost Sub CaseGen II Heater with Defrost Wiring KitUniversal Defrost Duct KitGen II Heater with Defrost Installation Kit2” Duct Hose Per Foot