Upload
others
View
8
Download
0
Embed Size (px)
Citation preview
GeneralSpecifications
<<Contents>> <<Index>>
BT200BRAIN TERMINAL
Yokogawa Electric Corporation2-9-32, Nakacho, Musashino-shi, Tokyo, 180 JapanTel.: 81-422-52-5690 Fax : 81-422-52-2018
GS 01C00A11-00EN
GS 01C00A11-00EN©Copyright May 19946th Edition: Mar. 2016
As a portable terminal, the Model BT200 BRAIN TERMINAL is used in combination with equipment using brain communication for setting, changing, displaying and printing out parameters such as tag number, output mode, and range, through simultaneous communication. It also monitors I/O values and self-check results, sets constant-current output , and allows zero adjustments. The Model BT200 BRAIN TERMINAL is used by connecting it between 4 to 20 mA DC signal transmission lines of the equipment or to a dedicated connector on the ESC (Signal Conditioner Communication Card) when the system is started up or maintained.
n FEATURESlOnlinemonitoringandcommunication
The modulated communication signal does not interrupt the 4 to 20 mA DC signals during communication.
lCommontoallYokogawa’sequipmentThe Model BT200 BRAIN TERMINAL works with all equipment that uses BRAIN communication.
lEasyofuseA large display (21 characters by 8 lines) eases setup and alteration procedures in English prompting interactive sequences.
lDiagnostics/securitywitherrormessages• Self-check function• Security code protection of setpoints• Low battery voltage alarm• Automatic power-off
lPrinter(BT200-P00)Printer prints out tag numbers and other parameters on the spot.
n STANDARD SPECIFICATIONSEquipmentSpecificationsApplicableEquipment:[FieldInstruments]
DPharpADMAGYEWFLOYTA
[SignalConditioner]Signal Conditioner for CENTUM
CommunicationSpecification:Yokogawa original protocol
Modulation: Burst modulation 0: 2400 Hz1: Signal without carrier
Baud rate:1200bpsCommunication signal: host to device: +/- 0.5 V (load resistance 250 Ω)device to host: +/- 2 mA
CommunicationLine:[FieldInstruments]
Load resistance: 250 to 600 Ω (including cable resistance)
Load capacitance: 0.22 μF or lessLoad inductance: 3.3 mH or lessPower line spacing: 15 cm (6 inch) or more (Avoid
parallel wiring.)[SignalConditioner]
Use dedicated cableLineLength:[FieldInstruments]
Up to 2 km (1.24 mile) (0.75 to 1.25 mm2
instrumentation cable)[SignalConditioner]
1.1 m with dedicated cableCommunicationSignalConnection:
Dedicated cable, 1.1 m long (3.6 ft)
[Style: S2]
2
All Rights Reserved. Copyright © 1994, Yokogawa Electric Corporation
<<Contents>> <<Index>>
GS 01C00A11-00EN
EMCConformityStandardsEN61326-1 Class A, Table2 (For use in industrial locations)
Display:LCD dot matrix, 21 characters×8 lines
Controls:Membrane switches (four function keys, 20 general operation keys, and one power switch)
Printer(BT200-P00):Thermal paper type
PowerSupply:Five AA 1.5 V dry alkali batteries (LR6/AM3 (N)), or Five AA 1.2 V Ni-MH batteries (HR6/AA)
Dimensions:BT200-N00 . . . 228×110×51 mm (9.0×4.3×2.0 inch) BT200-P00 . . . 321×110×61 mm (12.6×4.3×2.4 inch)
ApproximateWeight:BT200-N00 . . . 510 g (1.12 lb)BT200-P00 . . . 700 g (1.54 lb)
nFUNCTIONALSPECIFICATIONSBasicFunctions:l Setup, alteration, and display of parameters
BRAIN communication.: constant current output: Zero point adjustment
AdditionalFunctions:l Batch upload/download of datal Setpoint Protection:
Security code entry is required to alter setpoints.l Battery Alarm:
An alarm message appearing on the LCD announces low battery voltages.
l Automatic Power-off:The terminal is switched off automatically if no key access is made for approximately 5 minutes.
l LCD contrast adjustmentl Printing (BT200-P00)
PrintoutInformationl All parameter listsl Parameter list within each menu iteml Setup change data listl Uploaded data listl Display images l Self check list
nNORMALOPERATIONCONDITIONSBT200-N00 AmbientTemperature:
-15 to 55°C (5 to 131°F) AmbientHumidity:
5 to 95%RH at 40°C (104°F)BT200-P00 AmbientTemperature:
0 to 50°C (32 to 122°F) AmbientHumidity:
30 to 80%RH at 40°C (104°F)
n STORAGE CONDITIONSAmbientTemperature:
-15 to 60°C (5 to 140°F)AmbientHumidity:
5 to 95%RH at 40°C (104°F)30 to 80%RH at 40°C (104°F) (with printer)
n ACCESSORIESl CommunicationCable:
Two cables, one with alligator clips and one with IC clips (both snap-removable)
l Handycarrycase
nMODELANDCODE
Model SuffixCodes DescriptionBT200 . . . . . . . . . . . . . . . BRAIN Terminal
Printer-N . . . . . . . . . . . . . With no printer
-P . . . . . . . . . . . . . With printer
― 00 . . . . . . . . . Always 00
Options /
nPARTNUMBERS
Item PartsNo.
Communication Cable
With IC clips F9182EA
With alligator clips F9182EB
with 5-pin connector F9182EE
Roll paper F9182DS
Handy carry case F9182BP
n OPTIONS
Item Description CodeCommunication Cable with 5-pin connector
for SC (Signal conditioner) /C1
Mar. 31, 2016-00
3<<Contents>> <<Index>>
All Rights Reserved. Copyright © 1994, Yokogawa Electric Corporation GS 01C00A11-00EN
nCONNECTIONMETHOD
F01E.ai
Mar. 31, 2016-00
4
All Rights Reserved. Copyright © 1994, Yokogawa Electric Corporation
<<Contents>> <<Index>>
GS 01C00A11-00ENSubject to change without notice.
n DIMENSIONSModelBT200-N00
ModelBT200-P00
OrderingInformation1. Model and suffix codes
Mar. 31, 2016-00