General Catalogue - Høytrikksenteret Norge AS...General Catalogue Water Jetting Systems up to 3,000bar Edition No. 5 2 3 15 0 0 15 30 General overview of DYNAJET 4 28 – 31 36 –

General Catalogue

Water Jetting Systems up to 3,000 bar

Edition No. 5

2

www.dynajet-online.com

3

15°

40°

60°

15°

30°

General overview of DYNAJET

4

28 – 31

36 – 47

68 – 71

84 – 87

Professional cold- and hot-water high-pressure cleaners

Accessories up to 350 bar (5,075 PSI)

Accessories up to 1,200 bar (17,400 PSI)

General accessories

Overview of DYNAJET machines

6 – 15

32 – 33

48 – 59

72 – 79

88 – 89

Professional cold-water ultrahigh-pressure units



DYNAJET is where you are DYNAJET in action

Professional cold-water high-pressure cleaners

16 – 27

34 – 35

60 – 67

80 – 83

90 – 91

General overview of accessories and nozzles


Protective clothing

Terms and Conditions of Sale and Delivery


Table of Contents

4


DYNAJET is one of the global leaders in the development and manufacture of professional and innovative high-pressure cleaners. With a pressure of up to 3,000 bar, DYNAJET high-pressure cleaners fulfil all requirements and offer flexible solutions for virtually all sectors, whether it’s industry, construction, the skilled trades, local authorities, forestry or agriculture:With DYNAJET, you can clean and renovate efficiently, flexibly and econo-mically.

Quality and reliability made in GermanyAt DYNAJET, we focus on the highest quality right from the start. This means that only components and materials from reputable and approved suppliers in Germany or the EU are used to construct a DYNAJET high-pressure clea-ner. All DYNAJET high-pressure cleaners bear the CE mark and are manuf-actured at our headquarters near Stuttgart, Germany, in accordance with the European Machinery Directive 2006/42/EC.

DYNAJET service – worldwide competence and qualityIn cooperation with our DYNAJET partners, we provide a dense service network throughout the world: whether it’s competent purchasing advice, rapid repairs or reliable maintenance, professional service from DYNAJET is always available right near you.

DYNAJET service at a glance: A globally available service network Competent advice from trained professionals Short delivery times for machines, spare parts and expendables High quality standards and safety standards through use of original parts On-schedule maintenance by qualified personnel Service technicians on site Shorter down times and higher availability

DYNAJET – water in its most powerful form

5

6

www.dynajet-online.comProfessional high-pressure cleaners

Sturdy steel frame protects the machine against damage (can be used as a lifting eye)

Storage space for quick access to hoses, accessories and cables

Industrial paintwork provides the machine with long-lasting protection

Single-axle chassis with air filled tyres for easy manoeuvrability on site

Screwsgenerally made of corrosion-free materials

Stainless-steel water filter insert extends the operating life of the high-pressure pump, can be washed out

Main power switch also serves as an emergency shutdown and safety switch

Energy supply socket securely mounted and resistantto splash water

Manual pressure adjustment infinitely variable for optimum adaptation to the cleaning object (automatic hose pressure drop down system as option)

Safety valveprotects against overpressure

Frost protection system the intake of antifreeze liquidprevents possible damageto the pump

High-performance industrial crankshaft pump with ceramic pistons for extremely long operating times

Operating-hour meter important when servicing and renting equipment

Tilt switch for monitoring the horizontal working position; protects the pump

An overview of our electrically-operated trolliesYou can find technical data for our electric trollies on pages 16 to 19.

Simplest power supply and electrically-driven industrial motor provides mobility

Flexible, emission-free (no exhaust gases, noise, etc.) can be used anywhere Highest cleaning performance with the lowest weight and smallest footprint

Flexible coupling between the pump and the motor for easy servicing and to reduce vibrations

Large dimensioned bypass hose to prevent pressure peaks and temperature increases

Thermo valve protects the pump from overheating

Suction pressure control protects the pump against running dry and possible damages by cavitation

Robust, long-life industrial electric motor available for all worldwide voltages and frequencies

Manual star/ delta starterprotects the fuse on site (a requirement of EC standards from 7.5 kW upwards)

Electric trollies up to 500 bar (15 kW 20 Hp class)

7

Professional high-pressure cleaners

Sturdy steel frame protects the whole machine

Storage space for hoses and accessories


4-wheel modelfor 100% reliable stability and manoeuvrability on site

Screwsgenerally made of corrosion-free materials


Main power switch and emergency shutdown and safety switch

Energy supply socket (64 Ampere)securely mounted and resistantto splash water

Manual pressure adjustment infinitely variable (up to 800 bar) for optimum adaptation to the cleaning object (automatic hose pressure drop down system as standard)


High-pressure manometerfor displaying the working pressure

Frost protection system the intake of antifreeze liquidprevents possible damageto the pump

High-performance industrial crankshaft pump with ceramic pistons for extremely long operating times, slow running pump


Parking brakefor fixation

Central lifting eye for easy transportation and shipping

Large dimensioned bypass hose to prevent pressure peaks and temperature increases

V-belt driveto dampen vibrations and reduce pump motor speed

Internal stainless steel buffer tank with booster pumpto guarantee correct suction pressure (from 800 bar)

Cover panelsprotect machine and operator



Easiest power supply and electrically-driven by a powerful industrial motor Ideal for fix washing areas and installations Highest cleaning performance can be used universally up to 1,000 bar (14,500 PSI) with dry-stop pistol

Robust, long-life industrial electric motor available for all worldwide voltages and frequencies

Automatic star/ delta motor starterprotects the fuse on site

Electric trollies up to 1000 bar (30 kW 41 Hp class)

8


Industrial paintworkprovides the machine with long-lasting protection




Oil-pressure monitoring protects the engine from low oil level

Stainless-steel water filter insert extends the operating life ofthe high-pressure pump, can be washed out

Single-axle chassiswith air-filled tyres and sturdy steel rims for easy manoeuvrability on-site

Perfect centre of gravity flexible and effortless manoeuvrability

Electric starter for effortless starting

Storage space for hoses and accessories

Wear-free industrial gearbox between engine/ pump



An overview of our gasoline/ petrol-operated trolliesYou can find technical data for our gasoline/ petrol-operated trollies on pages 20 to 23.

Gasoline driven trollies up to 500 bar (7,250 PSI)

Central lifting eye for easy transportationand shipping

12 V socket for a mobile power supply to the Dynabox 12 V hot-water system

Can be used anywhere, independent on an external power supply Mobile concept provides powerful results at any location Modular, light-weight cold-water power pack

Manual pressure adjustment infinitely variable for optimumadaptation to the cleaning object(automatic hose pressure drop down system standard with 500 bar versions)


9


Diesel trollies up to 500 bar (7,250 PSI)


Safety valveprotects against over-pressure




Manual pressure adjustment infinitely variable for optimumadaptation to the cleaning object (automatic hose pressure drop down system as option)


Single-axle chassis with air filled tyres and robust steel rims, for easy manoeuvrability on-site

Perfect centre of gravity flexible and effortless manoeuvrability


12 V socketfor a mobile 12 V power supply for the Dynabox 12 V hot water system


Central lifting eye for easy transportationand shipping

Vibration-proof starter battery for effortless starting

Central start up, control and monitoring box with a display for the machinestatus and electric key starter

Anti vibration pads to absorb vibrations between pump, engine and frame

Cover with sound insulationprotection and noise reduction

Pressure sensor for switching to idle speed, saves fuel and ensures quiet operation. Hand throttle control available as option

An overview of our diesel-operated trolliesYou can find technical data for our diesel-operated trollies on pages 24 to 25.

Continuous operation, powered by a robust diesel engine Suited to a wide variety of uses independent on an external power supply Low fuel consumption with very high cleaning performance

10


Dynabox – mobile hot water at any location

An overview of our Dynabox You can find technical data for our Dynabox on pages 26 to 27.

Modular hot-water system, flexible use when needed, powered by diesel burner

Mobile use on site in combination with DYNAJET trollies up to 500 bar (7,250 PSI)

12 V version is not reliant on a fix external power supply line

Power supply possible for all worldwide networks(110 V, 230 V, 50 Hz, 60 Hz, etc.)

Available as a 12 V version for fix network-independent power supply (e.g. with a gasoline/ diesel trolly)

Quick-release hand couplings for very quick mounting/ removal

Inspection glass for easy burner servicing and control

Connection hose to high-pressure pump, shortens the set-up time, approx. 2 m, fix installed

Thermostat control infinitely variable temperature adjustment and adaptation tothe cleaning object

Fuel tank monitoringfor checking the fill level

Safety valve to protect against overpressure

Large tank opening for easy filling

Flow switch as a safety and switchingcomponent

Pressure switch for additional protection

Parking brake for holding it in position

Fixing pointsto fix the box and for transport

Powerful diesel burner electronic ignition system,blower and transformer foroptimized efficency

Photo cell as flame controlas a safety device

4-wheel type for 100 % reliable stability

11


The DYNAJET hot water system

Working principle:

The effect of heating the high-pressure water (with DYNAJET uniquely pos-sible up to 800 bar (11,600 PSI)) to almost 100 °C produces a turbocharged result in the cleaning and removal performance.

Depending on the type of surface (metal, etc.) and the layer to be removed (oil, grease, paint), the working time can be reduced by up to 4x compared with using cold-water alone.

Safety and efficiency:

The new developed burner control concept used and registered for a patent by DYNAJET further enhances the hot water technology:

Increased reliability Reduced number of components Increased safety Simplification of the whole system for the after-sales

department and service

Until mid 2008 Since mid 2008

M

M

M

M

DYNAJET 350 bar and hot water used in workshop floor cleaning

DYNAJET Innovation – “To make things easier for you”

Conventional system with common rail technology, switching via solenoid valves with central injection pump (Example: DYNAJET 500 th with two parallel burners).

DYNAJET concept (patent pending) with unit injector principle with no solenoid valves and independent, individually-controlled injection pumps (Example: DYNAJET 500 th with two parallel burners).

Diesel Diesel

Injection pump

➀

➀ ➀

➀

➁

➁ ➁

➁

Solenoid valves

Check valves

12


Minimized set-up time, due to the water tank and built-in hose drum it is immediately ready for use and easy to operate

Infinitely variable, wear-resistant pressure adjustment for optimum adaptation of the cleaning power to the object

Available in the DYNAJET 350 bar (5,075 PSI), 500 bar (7,250 PSI) and 800 bar (11,600 PSI) types Independent hot-water high-pressure cleaner for flexible

use at any location

Hot water trailers up to 800 bar (11,600 PSI) …

An overview of our hot-water trailersYou can find technical data for our hot-water trailers on pages 28 to 31.

Two separate cover hoods offering ideal access for the operator and for servicing

Optimized engine cooling extends life time

Easy frost protection system protects the unit in winter, DYNAJET 800 th with automatic anti-freeze function

Single-axle chassis for easy manoeuvrability

Hand throttle adjustment for making infinitely variableadjustments to the diesel enginespeed and pump pressure, 800 th with automatic system

Sturdy frame concepttested on a truck test track

Control cabinet simple control system, incl.12 V socket for energy supply

Shock-resistant plastic hoods reduces the weight, corrosion-free

Supply hose on drum so that the water supply runsimmediately – reduces set-up time

High-pressure hose on a drum no set-up and assembly time required; ideal space-saving storage, large operating range, 800 th with 2 times single loose drums

Water tank low level switch protects the high-pressurepump against running dry


Industrial shock absorbersand hinges robust, long-life technology

13


Targa concept ideal supply-air and exhaust-gas routing, reduces the noise level

Central lifting eye for easy transport site and for shipping

Separate engine, pump and burner areafor operator safety, easy access for servicing

Integrated hot water burnerfor extra cleaning performance, parallel connection burner makessure that pressure loss is kept to a minimum in 500 th und 800 th

Large integrated water tank for calming down the water and as a water store for independent operation, 1,000 litres in the DYNAJET 500 th and 800 th types

Protection frame to protect the machine

Frames in electrophoretic painting for long-lasting corrosion protection

Automatic pressure control systemideal adjustment to the required pressure via engine speed (800 th standard)

Anti vibration pads for dampening engine and pump vibrations

Large diesel tank for extended working times on site

… a family of powerful units for all applications

The hot water trailer is also available with an aluminium cover and vice

14

www.dynajet-online.comProfessional high-pressure units

Mobile ultra high-pressure units up to 2,800 bar (40,600 PSI)

Easy adaptation of the machine to the cleaning task (interchangable pump heads, operation of compressed-air tools and more)

Highly modern, user-friendly control system with large symbols and a text display for easy operation

Robust, modern, service-friendly machine concept with 2 cover hoods

An overview of our UHP cold-water unitsYou can find technical data for our cold-water trailers on pages 32 to 33.

Ultrahigh-pressure pump offering maximum efficiency, saves fuel, minimized virbations

Low-speed ultrahigh-pressure pump with an integrated oil coolerthat prevents overheating and extends the operating life

Diaphragm operated pressure regulation, safety and unloader valve switched and controlled by compressed air for soft switching without pressure peaks

Storage pack*for the safe storage of tools, spray lances, accessories, etc.

Carbide plungers offering the highest durabilityfor a long service life

Pump power end made out of cast iron, solid and reliable

Hood locks robust and adjustable, to lock and secure the machine

Easy operating-mode selection for selecting automatic pressure modus, manual use and compressed air tools

Powerful Deutz industrialdiesel engineupdate exhaust emission, low-speed engine for robust operation

Easy control system offering improved ease of operation through a large display with symbol and text indicators, complete with lockable protective cover that also acts as a sunshade

Frost protection systemwith integrated storage tank for simpliest protection of the machine in risk of frost.

Fine filter in stainless-steel casing for exchangable filter bags

Suction and high-pressure connections usable with closed hood

Prefilter with stainless-steel insert, can be washed out

15

Professional high-pressure units

Dual-hood targa concept for operator end engine side, offering ideal access and protection

Noise insulation reduces noise and sound power level

Integrated compressed-air system for operating rotating high-pressure tools

Lifting eye*Optionally available and can be retro-fitted

Protection frame to protect the machine

Storage area under the hood for tools,hoses and accessories

Optimum air flow for engine and high-pressure pump cooling

Frame and chassis produced to quality, tested on a truck test track

* Optionally avialable

Large fuel tank for long periods of use on-site

Mobile ultra high-pressure units up to 2,800 bar (40,600 PSI)

Closed bottom/ leak tray protects machine and environment against contamination

Vice*for quick nozzle change and service

Water storage tank for test surfaces, buffer and separator from supply lines

The storage pack with vice and hose fixation is available as an optionAnti-freeze system with integrated storage tank

16

www.dynajet-online.comProfessional cold-water high-pressure cleaners

Compact, powerful, mobile, flexible and well thought out, right down to the last detail. Like all DYNAJET high-pressure cleaners, the 15 kW (20 Hp) electric trollies have all of the features required for day-to-day use: high con-tinuous output, simple operation, long operating life and professional safety. The electric trollies are versatile, easy to transport and can be used flexibly for almost any application you can think of.

DYNAJET trollies from the 15 kW (20 Hp) me-class are flexible and emission-free (no exhaust gas, noise, etc.), for use anywhere.

Highest cleaning performance with the lowest weight and smallest footprint.

Simplest power supply and electrically-driven industrial motor provides mobility

Technical data DYNAJET 150 me DYNAJET 280 me DYNAJET 350 me DYNAJET 500 me

Type cold-water high-pressure cleanerMax. operating pressure 150 bar (2,175 PSI) 280 bar (4,060 PSI) 350 bar (5,075 PSI) 500 bar (7,250 PSI) Max. flow rate 42 l/min (11.1 US gal/min) 13 l/min (3.44 US gal/min) 21 l/min (5.56 US gal/min) 15 l/min (3.97 US gal/min)Pump triplex plunger pump with ceramic-coated plungersMotor (standard) electric motor 400 V, 50 Hz, IP54Medium (clear water) up to 40 °C, min. 1.8 bar, max. 6 bar supply pressureEngine output 15 kW (20 Hp) 7.5 kW (11 Hp) 15 kW (20 Hp) 15 kW (20 Hp) Speed of motor/ pump 1,450 rpm 1,450 rpm 1,450 rpm 1,450 rpm Pressure setting infinite manual adjustment of automatic pressure regulatorDischarge coupling M22 x 1.5 ET M22 x 1.5 ET M22 x 1.5 ET M24 x 1.5 ETChassis 2 wheels, single-axle trolly concept Weight 147 kg 97 kg 147 kg 147 kgL x W x H 110 x 66 x 65 cm 110 x 66 x 65 cm 110 x 66 x 65 cm 110 x 66 x 65 cm Part no. 1 488.016 1 489.002 1 488.003 1 509.018

The picture shows the DYNAJET 350 me in working positiontThe picture shows the DYNAJET 350 me in storage position

DYNAJET trollies me-type (15 kW 20 Hp)Mobile electrically-operated trollies up to 500 bar (7,250 PSI)

17


Accessory sets

All sets are supplied as single parts including sealing paste (heat-resistant). Further accessories and personal protective equipment can be found from page 36 onwards.

Automatic pressure regulation with bypass function for infinitely variable pres-sure adjustment (500 bar (7,250 PSI) type comes with automatic hose pres-sure drop down system), high-pressure gauge, manual star-delta and motor safety switch, frost protection function, operating-hours meter, stainless-steel water filter insert, safety valve, position monitoring, plug socket, supply-pressure and temperature-monitoring system, operating manual

Standard scope of supply Scope of supply

10 m high-pressure hose for hot/ cold-water, high-pressure cleaning gun with extension pipe (total length approx. 800 mm), nozzle carrier and 15° flat-jet nozzle

Special versions

Rotating nozzle system – Extension pipe – Hose connections – Rotating nozzle Part no.

150 me 460 043 280 me 459 340 350 me 459 342 500 me 459 345

WSS 500 water-sand-blasting system

– Extension pipe – Hose connections – Spray head incl. nozzle – Suction hose with suction pipe Part no.

150 me 460 044 280 me 459 346 350 me 459 348 500 me 459 352

Water/ sand-blasting system WSS 1000

– Extension pipe – Hose connections – Spray head incl. nozzle – Suction hose with

suction pipe Part no.

280 me 459 347 350 me 459 349 500 me 459 353

Part no.

DYNAJET Seamaid 1 509.122 500 bar (7,250 PSI) version for use on oceangoing vessels, e.g. for corrosion protection (440 V, 60 Hz), comes fully- equipped with nozzles, extension hose, stainless-steel cover, and much more

DYNAJET 500 me basic 1 509.187 Same as DYNAJET 500 me (Part no. 1 509.018), but automatic pressure regulation without hose pressure drop down system With automatic star-delta starter protects the fuse

and power supply, ideal for stationary installations Part no.

DYNAJET 350 me (400 V, 50 Hz) 1 488.032 DYNAJET 500 me (400 V, 50 Hz) 1 509.096

With fully automatic start/ stop function with automatic full shutdown or unit startup upon activation of the high-pressure cleaning gun; reduces wear and saves energy Part no.

DYNAJET 350 me (400 V, 50 Hz) 1 488.123 DYNAJET 500 me (400 V, 50 Hz) 1 509.148

Special voltages and frequencies

DYNAJET 150 me (400 V, 60 Hz) 1 488.045 DYNAJET 350 me (400 V, 60 Hz) 1 488.029 DYNAJET 500 me (400 V, 60 Hz) 1 509.044 DYNAJET 500 me (440 V, 60 Hz) 1 509.135

18


Compact, powerful, mobile and well thought out, right down to the last detail. Like all DYNAJET high-pressure cleaners, the 30 kW (41 Hp) electric trollies have all of the features required for day-to-day use: high continuous output, simple operation, long operating life and professional safety. The electric trol-lies are easy to transport and usable everywhere for nearly every imaginable application, even for on-site installations.

DYNAJET trollies from the 30 kW (41 Hp) me-class are flexible and emission-free (no exhaust gas, noise, etc.), universally usable.

Highest cleaning performance with the lowest weight. Easy power supply and electrically-driven industrial motor provides mobility.

Technical data DYNAJET 500 me-30 basic DYNAJET 500 me-30 DYNAJET 800 me-20 DYNAJET 1000 me-17

Type cold-water high-pressure cleanerMax. operating pressure 500 bar (7,250 PSI) 500 bar (7,250 PSI) 800 bar (11,600 PSI) 1,000 bar (14,500 PSI)Max. flow rate 30 l/ min (7.93 US gal/min) 30 l/ min (7.93 US gal/min) 20 l/ min (5.28 US gal/min) 17 l/ min (4.49 US gal/min)Pump 5-piston pump with triplex plunger pump triplex plunger pump triplex plunger pump with ceramic-coated plungers with ceramic-coated plungers with package seal, with package seal, rinsing/cooling rinsing/cooling and carbide plunger and carbide plungerMotor (standard) electric motor 400 V, 50 Hz, IP54Medium (clear water) up to 40 °C, min. 1.8 bar, max. 6 bar supply pressureEngine output 30 kW (41 Hp) 30 kW (41 Hp) 30 kW (41 Hp) 30 kW (41 Hp)Speed of motor/ pump 1,450 rpm/ 1.450 rpm 1,450 rpm/ 970 rpm 1,450 rpm/ 850 rpm 1,450 rpm/ 850 rpmPressure setting infinite manual adjustment of automatic pressure regulatorDischarge coupling M24 x 1.5 ET M24 x 1.5 ET M24 x 1.5 DKO ET M24 x 1.5 DKO ETChassis 4 wheels 4 wheels 4 wheels 4 wheelsWeight 450 kg 450 kg 560 kg 560 kg L x W x H 116 x 80 x 110 cm 116 x 80 x 130 cm 116 x 80 x 130 cm 116 x 80 x 130 cmPart no. 1 518.050 1 518.020 1 585.010 1 585.050

DYNAJET trollies me-type (30 kW 41 Hp)Mobile electrically-operated trollies up to 1,000 bar (14,500 PSI)

The new flagship in DYNAJET’s “me” class: the 1000 me.The first 1,000 bar (14,500 PSI) high-pressure cleaner without a control cable and with a dry-stop pistol.In the new DYNAJET 1000 me trolly, the best possible ergonomics are combined with maximum power to create concentrated efficiency.

Making DYNAJETting even more environmentally friendly, efficient and safe.

19


Accessory sets


Automatic pressure regulation with bypass function for infinitely variable pressure adjustment with automatic hose pressure drop down system, high-pressure and suction gauge, automatic star-delta and motor safety switch, frost protection function, operating-hours meter, stainless-steel water filter, safety valve, plug socket (63 Amp.), supply-pressure and temperature-monitoring system, operating manual

The version 800 me and 1000 me is also equipped with a stainless steel buffer tank and booster pump to guarantee correct suction pressure.

Standard scope of supply

10 m high-pressure hose for hot/ cold-water, high-pressure cleaning gun with extension pipe (total length approx. 800 mm), nozzle carrier and 15° flat-jet nozzle

Scope of supply

Special voltages special frequencies DYNAJET 800 me 440 V/ 60Hz 1 585 020 DYNAJET 500 me-30 basic 440 V/ 60 Hz 1 518 060 DYNAJET 500 me-30 440 V/ 60 Hz 1 518 040 DYNAJET 1000 me-17 440 V/ 60 Hz 1 585 060

Special versions

WSS 500 water-sand- blasting system

– Extension pipe – Hose connections – Spray head incl. nozzle – Suction hose

with suction pipe Part no.

500 me-30 459 350




500 me-30 459 351 800 me-20 487 234 1000 me-17 446 723


500 me-30 459 344 800 me-20 530 851 1000 me-17 546 724

20


DYNAJET trollies mg-typeMobile gasoline/ petrol-driven trollies up to 500 bar (7,250 PSI)

The mg-class provides convincing performance in the smallest of spaces. The mobile trollies are driven by a powerful gasoline/ petrol engine. They are not dependent on an external power supply. The mobile Dynabox 12 V hot-water generator can even be connected via a socket – providing unbeatable flexibility.

Hoses, the high-pressure cleaning gun and other accessories can be stored using a minimum of space or can be safely stowed during operation. Can be used anywhere,independent on an external power supply. Modular, light-weight cold-water power pack. Mobile concept provides powerful results on site.

The pictures show a DYNAJET 500 mg

Technical data DYNAJET 350 mg DYNAJET 500 mg

Type cold-water high-pressure cleanerMax. operating pressure 350 bar (5,075 PSI) 500 bar (7,250 PSI)Max. flow rate 21 l/ min (5.56 USgal/ min) 15 l/ min (3.97 USgal/ min)Pump triplex plunger pump with ceramic-coated plungersEngine 2-cylinder, 4-stroke gasoline/ petrol engineEngine output 14.5 kW (20 Hp) 14.5 kW (20 Hp)Speed of engine/ pump 3,250/ 1,450 rpm 3,250/ 1,450 rpmGear ratio i = 2.24 i = 2.24 Fuel consumption ø (normal gasoline) 5.5 l/ h (1.46 USgal/ h) 5.5 l/ h (1.46 USgal/ h)Medium (clear water) max. 40 °C, min. 1.8 bar, max. 6 bar supply pressureVolume of fuel tank 20 l (5.29 USgal) 20 l (5.29 USgal)Discharge coupling M22 x 1.5 ET M24 x 1.5 ETWeight (without fuel) 105 kg 128 kg(L x W x H) 75 x 79 x 99 cm 75 x 79 x 99 cmPart no. 1 486.005 1 486.050

21


Accessory sets

All sets are supplied as single parts including sealing paste (heat-resistant).Further accessories and personal protective equipment can be found from page 36 onwards.

Part no.

DYNAJET 500 mg basic Same as DYNAJET 500 mg

(Part no. 1 486.050), but automatic pressure regulation without hose pressure drop down system 1 486.092

2-cylinder gasoline/ petrol engine with electric starter, central lifting eye, operating-hours meter, stainless-steel water filter insert, engine key switch, engine-oil pressure monitoring system, 12 V DC socket, automatic pressure regulator with bypass function for infinitely variable pressure adjustment (500 mg type with automatic hose pressure drop down-system), supply-pressure and tempera-ture-monitoring system, safety valve and pressure gauge, operating manual


Special versions

10 m high-pressure hose for hot/cold-water, high-pressure cleaning gun with extension pipe (total length approx. 800 mm), nozzle carrier and 15° flat-jet nozzle

Scope of supply


– Extension pipe – Hose connections – Spray head incl. nozzle – Suction hose with suction pipe Part no.

350 mg 459 348 500 mg 459 352




350 mg 459 349 500 mg 459 353


350 mg 459 342 500 mg 459 345

22


DYNAJET trolly 350 mg Plus The all-rounder for truck-mounted concrete pump operators (among others) – combines three functions in one device

The DYNAJET 350 mg Plus is the truck-mounted concrete pump operator's Swiss army knife. This small, versatile piece of equipment offers 3 important functions at once in the same device.

The mobile, gasoline/ petrol-driven trolly achieves impres-sive values with a delivery rate of 21 l/ min (1,260 l/ h) and a max. operating pressure of max. 320 bar (4,640 PSI).

It is used to clean your concrete pump and also to remove the most heavy deposits and dirt.

When a hydraulic pump has broken down, you can use it as a standby

powerpack for hydraulic oil pumping. You can unclog concrete blockages in pipelines,

even when the concrete has been in the pipe for extended periods.

The DYNAJET 350 mg Plus is a device which no truck-moun-ted concrete pump should really be without.

Technical data DYNAJET 350 mg Plus

Type cold-water high-pressure cleaner or hydraulic power packMax. operating pressure 320 bar (4,640 PSI)Max. flow rate 21 l/ min (5.56 USgal/ min)Pump triplex plunger pump with ceramic-coated plungersEngine 2-cylinder, 4-stroke gasoline/petrol engineEngine output 14.5 kW (20 Hp)Speed of engine/ pump 3,250/ 1,450 rpm Gear ratio i= 2.24Fuel consumption ø 5.5 l/ h (1,46 USgal/ h) (at 60 % operative)Medium clean water max. 40 °C, hydraulic oil, max. temperature 70 °CDischarge coupling water M22 x 1.5 ETVolume of fuel tank 20 l (5.29 USgal)Weight (without fuel) 110 kgL x W x H 75 x 79 x 99 cmPart no. 1 486.089

23


Accessory sets

2-cylinder gasoline/ petrol engine with electric starter, central lifting eye, operating-hours meter, integrated stainless-steel water filter insert, engine key switch, engine-oil pressure monitoring system, 12 V DC socket, automatic pressure regulator with bypass function, pressure gauge, level sensor to pro-tect the machine from running dry, temperature-monitoring, operating manual


For water operation: see page 21 (same as DYNAJET 350 mg) For hydraulic oil operation:

suction hose, pressure hose, connection

For pipe cleaning operation: 5 x extension pipe 1.0 m, rotating nozzle, 2 x couplings, pipe-cleaning nozzle piece with check valves


Scope of supply




350 mg Plus 459 348

Water/ sand-blasting system WSS 1000 – Extension pipe – Hose connections – Spray head incl. nozzle – Suction hose


350 mg Plus 459 349

Rotating nozzle system – Extension pipe – Hose connections – Rotating nozzle Part no. 350 mg Plus 459 342

Concrete-pipe cleaning package. Included in scope of supply:

– 5 x 1.0 m extension pipe – 1 x rotating nozzle – 2 x couplings – 1 x pipe-cleaning nozzle Part no.

350 mg Plus 464 155

Special accessories for pipe cleaning – High-pressure hose 25 m – 2 x pipe-cleaning nozzles Part no.

350 mg Plus 494 658

24


DYNAJET trollies md-typeRobust diesel trollies up to 500 bar (7,250 PSI)

Trollies from the md-class are compact, diesel-operated cold-water high-pressure cleaners. They are therefore not dependent on an external powersupply. The powerful diesel engine makes it even more robust and reliableand means that they use less fuel.

Thanks to the idling system, the diesel trolly slows to idling speed after a short time without high-pressure. This reduces noise and fuel consumption, and extends maintenance intervals.

The diesel trollies are completely encapsulated and soundproofed. Hoses such as the high-pressure cleaning gun and other accessories can be stored on the machine using a minimum of space or can be safely stowed during operation.

Trollies from the md-class are robust units offering continuous operation, powered by a diesel engine.

Use for to a wide variety of applications is possible as it is not dependent on an external power supply.

The fuel consumption is very low despite offering the highest cleaning performance.

The picture shows DYNAJET 500 md

Technical data DYNAJET 350 md DYNAJET 500 md

Type cold-water high-pressure cleanerMax. operating pressure 350 bar (5,075 PSI) 500 bar (7,250 PSI)Max. delivery rate 21 l/ min (5.56 USgal/ min) 15 l/ min (3.97 USgal/ min)Pump triplex plunger pump with ceramic-coated plungers Engine 2-cylinder Hatz diesel engine, air-cooled Engine output 14.5 kW (20 Hp) 14.5 kW (20 Hp) Speed of engine/ pump 2,900/ 1,450 rpm 2,900/ 1,450 rpmGear ratio i = 2.0 i = 2.0 Fuel consumption ø approx. 4.0 l/ h (1.06 USgal/ h) approx. 4.0 l/ h (1.06 USgal/ h) Discharge coupling M22 x 1.5 ET M24 x 1.5 ETMedium (clear water) max. 40 °C, min. 1.8 bar, max. 6 bar supply pressureVolume of fuel tank 20 l (5.29 USgal) 20 l (5.29 USgal)Weight (without fuel) 215 kg 215 kg L x W x H 91 x 80 x 96 cm 91 x 80 x 96 cmPart no. 1 513.010 1 513.020

25


Accessory sets


2-cylinder air-cooled diesel engine, safety equipment such as engine key switches, oil-pressure monitoring system, operating-hours meter, integrated stainless-steel water filter insert, automatic pressure regulator with bypass function (500 bar (7,250 PSI) types come with automatic hose pressure drop down-system), speed reduction, pressure relief safety valve, protection against dry run, 12 V socket, lifting eye, temperature-monitoring system and pressure gauge, operating manual


Special equipment

Special versions

10 m high-pressure hose for hot/cold-water, high-pressure cleaning gun with extension pipe (total length approx. 800 mm), nozzle carrier and 15° flat-jet nozzle

Part no.

Exhaust system with spark arrestor instead of standard exhaust system for DYNAJET md-trollies 503 030

Basic versions: Same design as the standard machine, but featuring speed adjustment via manual control (no automatic engine speed reduction), auto-matic pressure regulation (unloader valve) with no hose pressure relief. Part no.

DYNAJET 350 md basic 1 513.100 DYNAJET 500 md basic 1 513.200

Scope of supply




350 md 459 348 500 md 459 352

Water/ sand-blasting system WSS 1000 – Extension pipe – Hose connections – Spray head incl. nozzle set – Suction hose


350 md 459 349 500 md 459 353


350 md 459 342 500 md 459 345

26

www.dynajet-online.comHot-water generator

Dynabox systemUpgrades DYNAJET trollies into powerful hot-water units

The Dynabox is the ideal complement to all DYNAJET trollies. Simply connectit up on the high-pressure side between the high-pressure unit and the cleaning tool. You will be working with high-pressure water with a temperature up to 110 °C and achieving results which would not be possible with cold-water.

The pictures show the Dynabox 350

Technical data Dynabox 350 Dynabox 350/ 12 V Dynabox 500 Dynabox 500/ 12 V

Max. operating pressure 350 bar (5,075 PSI) 350 bar (5,075 PSI) 500 bar (7,250 PSI) 500 bar (7,250 PSI)Max. temperature 110 °C 110 °C 110 °C 110 °CTemperature increase approx. 55 °C at 21 l/ min (5.56 USgal/ min) approx. 65 °C at 15 l/ min (3.97 USgal/ min) Heat output 67 kW (94 Hp) 67 kW (94 Hp) 67 kW (94 Hp) 67 kW (94 Hp)Fuel Diesel/ heating oil Diesel/ heating oil Diesel/ heating oil Diesel/ heating oilTank volume 18 l (4.76 USgal) 18 l (4.76 USgal) 18 l (4.76 USgal) 18 l (4.76 USgal)Supply voltage 230 V/ 50 Hz 12 V DC 230 V/ 50 Hz 12 V DCWeight 129 kg 129 kg 129 kg 129 kgDischarge coupling outlet M22 x 1.5 ET M22 x 1.5 ET M24 x 1.5 ET M24 x 1.5 ETL x W x H 80 x 75 x 90 cm 80 x 75 x 90 cm 80 x 75 x 90 cm 80 x 75 x 90 cmArt.-Nr. 1 492.002 1 492.060 1 521.022 1 521.009

Further accessories and personal protective equipment can be found from page 36 onwards.

27

Hot-water generator

Dynabox 350 in different voltages (100 V, 120 V) and frequencies (50 Hz, 60 Hz) Part no.

for 100 V, 50/ 60 Hz 1 492.028 for 120 V, 60 Hz 1 492.031 for 220 V, 60 Hz 1 492.057

Mechanical safety valve to act as a safeguard, manual thermostat for temper-ature regulation and as an on/ off switch, safety pressure switch, outlet hose connection, flow controller for monitoring the water flow, flame monitoring via photo cells in the combustion chamber, inspection glass for carrying out visual inspections, control system with reset button for fault monitoring (not in 12 V types), operating manual

Dynabox 350/ 500 standard scope of supply

Special versions

The specifications and design are like the 230 V Dynabox, but with a supply voltage of 12 V. The 12 V DC Dynabox can be connected to and operated by DYNAJET trollies with combustion engine, via the standard 12 V socket. A 230 V supply power line is not necessary.

Variant: Dynabox 12 V version

Scope of supply

approx. 2 m high-pressure hose 5⁄16” (DN8), approx. 3 m connect-ing cable, plug for 230 V or 12 V (depending on type)

28

www.dynajet-online.comProfessional cold- and hot-water high-pressure cleaners

DYNAJET 350 th

The small power station for all applications

The flexible single-axle trailer. Easy to manoeuvre, light-weight, compact, powerful and well thought out down to the finest detail. Ideal for cleaning professionals, renovators and all users who require the highest performance through a combination of water pressure, water quantity and optimum water temperature. These professional devices are all operated by powerful diesel engines.

Independent hot-water high-pressure cleaners for flexible use at any location. Due to its water tank and fixed hose drum, the DYNAJET 350 th is ready for

immediate use, less start up time. Infinitely variable wear-resistant pressure adjustment gives cleaning performance that is perfectly adapted to the object.

The picture shows the DYNAJET 350 th

The picture shows the built-in module for the DYNAJET 350 sh

Technical data DYNAJET 350 th DYNAJET 350 sh

Type hot and cold-water, mobile hot and cold-water, stationaryMax. operating pressure 350 bar (5,075 PSI) 350 bar (5,075 PSI)Max. flow rate 7-16 l/ min (1.85-4.23 USgal/ min) 7-16 l/ min (1.85-4.23 USgal/ min)Pump triplex plunger pump with ceramic-coated plungersEngine (water-cooled) Kubota 3-cylinder diesel engine 13 kW (18 Hp)Speed of engine/ pump max. 3,000/ 1,090 rpm max. 3,000/ 1,090 rpmDischarge coupling M22 x 1.5 IT M22 x 1.5 ITPump/ engine via V-belts via V-beltsFuel consumption ø 3.9 l/ h (1.03 USgal/ h) (at 100 % operative)Heating power of oil burner max. 1 x 115 kW (159 Hp) (ca. 95 °C) max. 1 x 115 kW (159 Hp) (ca. 95 °C) Consumption of oil burner 7 l/ h (at 60 % operative) 7 l/ h (at 60 % operative)Water-tank capacity 300 l (79.36 USgal) 300 l (79.36 USgal)Volume of fuel tank 70 l (18.52 USgal) 70 l (18.52 USgal)Chassis single axle trailer with brake - Weight (without water) 760 kg 680 kgL x W x H (open) 248 x 172 x 210 cm 183 x 122 x 195 cmL x W x H (closed) 248 x 172 x 172 cm 152 x 122 x 146 cmPart no. 14 80.010 14 80.030

29


Accessory sets


Operating-hours meter, hand-throttle control, lifting eye, 12 V energy supply socket in the control cabinet, 50 m high-pressure hose (NW 8), and 25 m supply hose mounted on a hose drum, 300 litre water tank with gauge and moni-toring system, hot-water system, safety valve, pressure regulation valve, operat-ing manual


Special equipment

Part no. Built-in module for the DYNAJET 350 sh identical to DYNAJET 350 th, but instead of chassis with installation frame incl.

forklift slots for internal transport or for installation in a transporter or trailer, common exhaust manifold and with one plastic hood on the engine side 1 480.030

DYNAJET 350 th automatic hose pressure drop down-system for safe and convenient operation 1 480.040 DYNAJET 300 th

Identical to the DYNAJET 350 th, but with approx. 300 bar (4,350 PSI) working pressure and a delivery rate of approx. 19 l/ min (5,03 USgal/ min) 1 480.050

Special versions

High-pressure cleaning gun with extension pipe (total length approx. 800 mm), nozzle carrier and 15° flat-jet nozzle, storage box

Scope of supply

Additional plastic hood (for example as an upgrade for sh-types) Part no. 410 703 (grey tone RAL 7038) Part no. 410 706 (blue tone RAL 5007) Electronic throttle control

Electronic speed adjustment via control cabinet with automatic speed reduction with closed spray gun Part no. 533 221 Height-adjustable towing gear

for truck/ tractor unit incl. coupling Part no. 423 862 12 V working headlight, complete with 2 m

spiral cable and magnetic foot Part no. 437 116 1 set of spark arrestors for engine + burner Part no. 426 499 Additional supporting foot for side assembly Part no. 418 376 Connection hose for high-pressure hoses

with straight couplings to the drum, length 0.5 m, connections 3⁄8” BSP 90/ M22 x 1.5 ET

Part no. 430 243


350 th, 350 sh 459 340

Water/ sand-blasting system WSS 500 – Extension pipe

– Hose connections – Spray head incl. nozzle – Suction hose


350 th, 350 sh 459 346

Water/ sand-blasting system WSS 1000 – Extension pipe

– Hose connections – Spray head incl. nozzle set – Suction hose


350 th, 350 sh 459 347

30

www.dynajet-online.comProfessional cold- and hot-water high-pressure cleaners

DYNAJET 500 th and 800 th

The powerful all-rounders

Unbeatable mobility and versatility thanks to the single-axle principle when combined with the optimum setup of water pressure, water quantity and perfect hot-water temperature.

Independent hot-water high-pressure cleaners for flexible use at any location. Due to its water tank and fixed hose drum, the DYNAJET 500 th is ready for immediate use. The wear-resistant pressure adjustment is infinitely variable, so that the cleaning performance can be ideally adapted to the cleaning object.

The pictures show the DYNAJET 500 th

Technical data DYNAJET 500 th DYNAJET 800 th

Type hot and cold-water hot and cold-waterMax. operating pressure 500 bar (7,250 PSI) 800 bar (11,600 PSI)Max. flow rate 15-30 l/ min (3.97-7.94 US gal/ h) 10-21 l/ min (2.65-5.56 US gal/ h)Pump triplex plunger pump with ceramic-coated pistonsEngine (oil cooled) Deutz three-cylinder diesel/ 34 kW (46.2 HP) Speed of engine/ pump 2,600/ 1,000 rpm 2,300/ 800 rpmFuel consumption ø 10 l/ h (2.65 USgal/ h) at full load 10 l/ h (2.65 USgal/ h) at full load Heating power of 2 oil burners (effective) 2x 91 kW (125 Hp) 2x 65 kW (90 Hp)Consumption of the two oil burners total approx. 7 l/ h (1.85 USgal/ h) (at 60% operative)Water-tank capacity 1,000 l (264.55 USgal)Fuel/ heating-oil tank capacity 70 l/ 105 l (18.52 USgal/ 27.78 USgal)Discharge coupling M24 x 1.5 IT M24 x 1.5 DKO ETChassis single axle trailer with brakeWeight (without water) 1,600 kg 1,640 kgL x W x H 365 x 210 x 210 cm 365 x 210 x 210 cmPart no. 1 490.020 1 529.010

31


Accessory sets


2x high performance water burners, powerful diesel engine, 12 V socket, high-pressure hose* and 25 m low-pressure supply hose with hose drum, safety valve, automatic hose pressure drop down-system, 1,000 l (264.55 USgal) water tank, lifting eye, operating manual. DYNAJET 800 th also come with automatic frost protection and decalcification system.

Standard scope of supply*

Special equipment

Special versions

DYNAJET 500 t Part no.

Available as a cold-water machine without hot-water burner in the following technical versions:

500 bar (7,250 PSI)/ 30 l/ min On request 400 bar (5,800 PSI)/ 37 l/ min 1 490.040 Built-in module for the DYNAJET 500 sh/ 800 sh

Identical technical data to DYNAJET 500 th and 800 th, but without chassis, mounted on an installation frame with forklift slots for internal transport and/ or installation and assembly, with 2 cover hoods,

weight 1.420 kg (500 sh) resp. 1.460 kg (800 sh) L x W x H (closed): 220 x 147 x 177 cm L x W x H (open): 307 x 147 x 246 cm DYNAJET 500 sh 1 490.030 DYNAJET 800 sh 1 529.030

DYNAJET 500 th – Special Part no.

Specifications as the 500 th but with following additional scope: spark arrester for engine and burner, battery disconnecting switch, connection socket for external remote emergency shutdown 1 490.070 DYNAJET 800 th wireless Specifications are identical to 800 th, but without remote

control cable to gun, without cable reel and without automatic speed-pressure control. Manual speed adjustment via manual throttle analogous to 500 th. Without integrated anti-freeze and decalcification system. 1 529.080

* The 500 th type is equipped with a 50 m high-pressure hose on a fixed hose drum. The 800 th type is equipped with 2x 10 m high-pressure hoses on loose storage drums and 20 m remote control cable on a loose drum.

High-pressure cleaning gun with extension pipe (total length approx. 800 mm), nozzle carrier and 15° flat-jet nozzle, storage box

Scope of supply

Part no.

Decalcification unit (for 500 th/sh) 438 165 12 V working headlight complete with

approx. 2 m spiral cable and magnetic foot 437 116 1 set of spark arrestors (for 500 th/ 800 th) or the diesel engine and for both hot-water burners, complete with connection parts 500 th 439 998 800 th 490 172 Connection hose (for 500 th)

for high-pressure hoses with straight couplings to the drum, length 0.5 m, connections 3⁄8” BSP 90/ M24 x 1.5 ET 459 593

Cover for operator‘s side for 500 sh/ th/ t made of aluminium, complete with storage box made of stainless steel and vice 518 729

External emergency stop button with cable drum 50 m cable, additional accessories only fit with 500 th – Special (Part no. 111 490.070) 458 018

Electronic throttle control Automatic electronic speed adjustment governed by operation of the spray gun. On request

Rotating nozzle system – Extension pipe – Hose connections – Rotating nozzle Part no. 500 th 459 344 800 th 531 125 Water/ sand-blasting system

WSS 500 – Extension pipe

– Hose connections – Spray head incl. nozzle – Suction hose


500 th 459 350 Water/ sand-blasting system

WSS 1000 – Extension pipe

– Hose connections – Spray head incl. nozzle – Suction hose with suction pipe Part no.

500 th 459 351 800 th 487 234

32

➀ ➁ ➂

www.dynajet-online.comProfessional cold-water ultrahigh-pressure units

DYNAJET UHP 170Maximum power – the 170 Horse Power class of DYNAJET ultrahigh-pressure units

The picture shows the DYNAJET UHP 170 as a mobile trailer with noise insulating hoods

Technical data UHP 170-1000 UHP 170-1200 UHP 170-2000 UHP 170-2800

Type cold-water ultrahigh-pressure unitMax. operating pressure 1,000 bar 1,200 bar (17,400 PSI) 2,000 bar (29,000 PSI) 2,800 bar (40,600 PSI)Max. flow rate 27-54 l/min 18.5-40.5 l/ min 10.5-23.5 l/ min 8.3-18 l/ min (1,620-3,240) (4.89-10.71 USgal/ min) (2.78-6.22 USgal/ min) (2.20-4.76 USgal/ min)Pump low-speed high-pressure pump with three carbide plungers, integrated reduction gear and oil coolerEngine (oil-cooled) Deutz 4-cylinder diesel (TCD 2013L04 2V) with 125 kW (170 Hp) at 2,400 rpm Speed of engine/ pump 1,100-2,200 rpm/ 257-565 rpm Water-tank capacity approx. 70 l (18.5 USgal) 70 l (18.5 USgal) 70 l (18.5 USgal)Volume of fuel tank approx. 190 l (50.26 USgal) 190 l (50.26 USgal) 190 l (50.26 USgal)➀ L x W x H (stationary without hoods)/ weight 250 x 140 x 185 cm/ approx. 2.100 kg➁ L x W x H (stationary with hoods)/ weight 255 x 140 x 185 cm/ approx. 2.260 kg➂ L x W x H (mobile trailer with hoods)/ weight 392 x 188 x 210 cm/ approx. 2.420 kg ➀ Part no. (stationary without hoods) 1 600.210 1 600.230 1 600.240➁ Part no. (stationary with hoods) 1 600.110 1 600.130 1 600.140➂ Part no. (mobile with hoods) 1 600.050 1 600.010 1 600.030 1 600.040

This UHP units represents the high end class for mobile DYNAJET high-pressure units, delivering pressures up to 2,800 bar (40,600 PSI). They are ultrahigh-performance machines that are intended for the most difficult and demanding jobs. They are economical, easy to operate and offer high levels of safety.

They are ideally suited to building renovation, paint stripping, rust removal, surface removal or even, for instance, heat exchanger cleaning. Even the mostdifficult deposits and coatings are quickly removed.

33

Professional cold-water ultrahigh-pressure units

Simple control system and complete monitoring in a small space, with protective cover, protects against dirt and also acts as a sunshade.

The operating and service covers, which can be opened very wide, making it easy to reach all the important parts.


Robust, durable Deutz four-cylinder diesel engine, three-plunger high-pressure pump with carbide plungers, power end cooling system, water temperature-monitoring system, storage tank with booster pump inc. filter and suction-pressure monitoring system, protection/ leakage tray, simple frost protection system with storage tank, total control with pressure-value presetting or option to choose manual engine speed control, simple to control via the display, dual-hood targa principle (depending on the type), chassis and noise insulation cover, manual.

Standard scope without accessories. Suitable accessories and accessories packages as well as personal protective equipment can be found from pages 68 onwards.

Special equipment

Part no.

Spark arrestor for diesel engine, is mounted on the outside on the machine chassis. Retrofit possible 501 396

Additional emergency stop button, on cable drum with 50 m cable and plug 458 018

Height-adjustable towing gear with truck/ trailer coupling ring On request Crane lifting eyes, consisting of 1 complete set

of heavy load crane eyes plates and assembly instructions. Retrofit possible 522 834

Easy frost protection system consisting of installation frame, pipework, manual ball valve and frost protection container (25 l), without filling. Retrofit possible 527 829

Stainless steel tool and storage box, mounted above the high-pressure pump, storage option for tools, accessories, etc. complete with vice for simple nozzle replacement. Retrofit possible 525 616

Lance holder, complete set for fixing and storage of one spray lance. Retrofit possible 525 668

34

www.dynajet-online.comDYNAJET accessories

DYNAJET accessoriesDN: Diameter (mm) IT: Internal threadPN: Max. operating pressure (bar) ET: External thread

Technical information on threaded unions, sealings, connections and extension pipes

350 bar M22 x 1,5 O-ring/support ring 1⁄4” = 12,9 mm(5,075 PSI)

500 bar M24 x 1,5 2 x O-ring/support ring 3⁄8” = 17,2 mm(7,250 PSI)

800 – 1200 bar M24 x 1,5 DKO Cone seal/O-ring 9⁄16” = 14,3 mm(11,600- 17,400 PSI)

>1200 – 2800 bar 9⁄16” - 18 UNF-LH Metallic sealing via cone 9⁄16” = 14,3 mm (17,400- suitable for extension pipes and 40,600 PSI) old UHP-hose system

Pressure range Thread Seal Extension pipes

35

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

Nozzles – a general overview

An overview of DYNAJET nozzle shapes and types

Shape A – round-jet nozzle

With 1⁄4” NPT outside thread (cone-shaped thread), max. 500 bar (7,250 PSI), extremely hard spot jet for removal on small surfaces, can be screwed into any nozzle carrier, sealed with sealing paste or teflon tape.

Shape C – round/ spot jet nozzle

Plug-in nozzle version, for use up to max. 1,600 bar (23,200 PSI), extremely hard spot jet for the most difficult deposits, water jet has a very high water jet speed, effective energy transformation, held in the nozzle carrier via union nut, seal via sealing ring (Part no. 484 295) and support ring (Part no. 489 307).

Shape E – nozzle insert for small dimensions

Small sapphire round-jet nozzle with outside thread and quadruple edge (5 mm), for use up to max. 1,000 bar (14,500 PSI), extremely small dimen-sions, long operating life thanks to the use of sapphire, used in the WSS 1000 water-sand-blasting system, seal via sealing glue.

Shape G – ultra high-pressure round-jet nozzle

Ultra high-pressure nozzle for conti-nuous use with carbide inserts, high speed nozzle thanks to extremely high efficiency, for use up to max. 3,000 bar (43,500 PSI), screwed directly into nozzle carrier or rotating nozzle system, only available as a round-jet nozzle, with hexagon socket and M10 outside thread, metallic cone seal, in use with UHP-types.

Shape B – flat-jet nozzle With 1⁄4” NPT outside thread, max.

500 bar (7,250 PSI), available in vari-ous jet angles 15°, 25° or 40°, for quick surface removal, to be screwed directly into any nozzle carrier, iden-tical sealing procedure as with shape A (sealing paste or teflon tape). Stan-dard scope of supply of all models up to 350 bar (5,075 PSI) as 15° nozzle.

Shape D – flat-jet nozzle

Plug-in nozzle version, for use up to max. 1,600 bar (23,200 PSI), availa-ble as 15° or 30° jet angle, high surface power with hard jet pressure, held in the nozzle carrier via union nut, seal via sealing ring (Part no. 484 295) and support ring (Part no. 489 307).Standard scope of supply of all models up to 500-1,200 bar (7,250-17,400 PSI) as 15° nozzle.

Shape F – turbo-type rotating nozzle

Universal multi-purpose jet nozzles for use up to max. 2,500 bar (36,250 PSI), combines the advantages of a large surface power and an extremely hard water jet, for maximum cleaning performance with very high surface power, variation in design depen-ding on the pressure level, speed adjustment also available in types up to 350 bar (5,075 PSI), for adapting cleaning performance to the object in question, nozzle pin and ceramic seat can be replaced as a repair kit, threa-ded connection 1⁄4” IT up to 500 bar (7,250 PSI) or 9⁄16” - 18 UNF-LH from 800 bar (11,600 PSI) and higher.

36

www.dynajet-online.comAccessories up to 350 bar (5,075 PSI)

Accessories up to 350 bar (5,075 PSI)DN: Diameter (mm) IT: Internal threadPN: Max. operating pressure (bar) ET: External thread

Connections via quick-release couplings M22 x 1.5 Part no.

DN 8, length 10 m, connections 2x M22 x 1.5 IT, 150 °C 440 607DN 8, length 25 m, connections 2x M22 x 1.5 IT, 150 °C 440 606DN 8, length 50 m, connections 2x M22 x 1.5 IT, 120 °C 491 994

O-ring for quick-release coupling 471 538Support ring for quick-release coupling 434 458

High-pressure extension hoses

Hose connection

Swivel joint

Part no.

double nipple for coupling two high-pressure hoses, connections 2x M22 x 1.5 ET 427 518

With servo valve for simple and easy operation with minimised and holding forces, trigger locking system, completely insulated, ideal for work with hot water,

inner parts made of stainless steel, overall length approx. 400 mm Part no.

Gun up to 150 °C Hose connection M22 x 1.5 ETOutlet connection M22 x 1.5 IT 466 255Repair kit for high-pressure cleaning gun 350 (Part no. 466 255) 501 274O-ring for outlet quick-release coupling 471 538Support ring for outlet quick-release coupling 434 458

Part no.

Side-mounted handgrip for the high-pressure gun 350, no tool required for retrofitting, infinitely adjustable 446 916

Part no.

Between the gun and the extension pipe, connections M22 x 1.5 ET/ 1⁄4” IT, complete with O-ring 427 197Spare O-ring 436 797

Part no.

Use directly on the gun inlet between the high-pressure hose and the high-pressure cleaning gun to avoid twists in the hose, connections M22 x 1.5 ET/ M22 x 1.5 IT 446 920

Swivel joint

Handle

Coupling

37

21


Part no.

For shape A and B nozzles, connection 1⁄4” IT directly onto the extension pipe 495 294

Part no. For sealing shape A and B nozzles 000 306

Part no.

For shape C and D plug-in nozzles, connection 1⁄4” IT, complete with O-ring for connecting directly to the extension pipe 431 516

Part no.

For direct connection to the high-pressure cleaning gun – connection M22 x 1.5 ET, length approx. 650 mm, 2 nozzle carriers for shape A or B nozzles, infinite regulation of pressure via valve with handgrip, equipped with 1 low-pressure nozzle (Part no. 506 422), shape B 427 460Spare parts kit for regulating valve 505 583

Extension pipes

Nozzle carrier

Teflon sealing tape

Nozzle carrier

Sealing ring and support ring

Part no.

Length 350 mm, 1⁄4” ET/ 1⁄4” ET 427 179Length 800 mm, 1⁄4” ET/ 1⁄4” ET 427 584

DYNAJET recommendation:for safety reasons, you should always select a spray wand of 350 mm or longer, so that when combined with thehigh-pressure cleaning gun 350 and nozzle carrier, an overall length of approx. 800 mm is reached.

DN: Diameter (mm) IT: Internal threadPN: Max. operating pressure (bar) ET: External thread

Part no.

(Fig. 1) Sealing ring for shape C and D plug-in nozzle 484 295(Fig. 2) Support ring for shape C and D plug-in nozzles 489 307

Double spray lance

38


Flat-jet nozzle, plug-in type (shape D)

Machine type Description Shape Part no.

15° jet angle 280 me + 350 th 1.3 D 498 402 350 me + 350 mg + 350 md 1.6 D 436 922

30° jet angle 280 me + 350 th 1.3 D 447 887 350 me + 350 mg + 350 md 1.6 D 438 679

High-pressure jet nozzles

Round-jet nozzles (shape A)


150 me 015 A 427 333280 me + 350 th 0035 A 414 019350 me + 350 mg + 350 md 005 A 427 136

Flat-jet nozzles (shape B)


15° jet angle (standard)150 me 1515 B 425 853 280 me + 350 th 15034 B 414 016 350 me + 350 mg + 350 md 1505 B 427 144

25° jet angle 150 me 2515 B 414 017 40° jet angle 150 me 4015 B 427 137 280 me + 350 th 40034 B 427 138 350 me + 350 mg + 350 md 4005 B 427 141

Round-jet nozzle, plug-in type (shape C)


280 me + 350 th 1.1 C 438 670350 me + 350 mg + 350 md 1.3 C 438 673


39


Rotating nozzles

Rotating nozzle with manual speed adjustment

Special types with heat-resistant ceramic for rotor and seat, protection cover made of plastic, for use up to 150 °C, connection 1⁄4” IT(Please note: Always start rotor nozzles downwards. Otherwise the rotor may get damaged.)


150 me 150 F 414 024 280 me + 350 th 035 F 414 023 350 me + 350 mg + 350 md 050 F 427 498

For adapting the jet strength for sensitive or changing surfaces, for use up to 150 °C, connection 1⁄4” IT


280 me + 350 th 035 F 414 025 350 me + 350 mg + 350 md 050 F 427 589

Repair kits

For shape F rotating nozzles – consisting of replacement nozzles and ceramic seat, specially designed for the high water temperatureswith DYNAJET machines

Nozzle type Description Part no.

for nozzle 414 024 150 414 028 for nozzle 414 023 035 414 027for nozzle 427 498 050 427 499

nozzles with speed adjustment:for nozzle 414 025 035 414 029 for nozzle 427 589 050 431 485

Poly nozzle

Multi-jet nozzle, ideal for removing chewing gum, for use up to max. 90 °C, connection 1⁄4” IT, housing made out of brass with integrated metal filter

Machine type Description Part no.

for 280 me + 350 th 035 461 181 for 350 me + 350 mg + 350 md 050 461 182


40



Suction pipe for WSS 500

Part no. The abrasive quantity is infinitaly adjustable, placed directly in the abrasive material (e.g. in a bucket) 414 036

Water-sand-blasting system WSS 1000

Part no.

Professional abrasive-blasting head for continuous use, ring-shaped arrangement of the high-pressure nozzles, central abrasive supply, tungsten carbide focus nozzle, connection 9⁄16” – 18 UNF IT, connection for shape E high-pressure nozzle (3 pieces), shape E nozzle inserts are notincluded in the scope of supply 435 111Spare tungsten carbide focus nozzle for WSS 1000 450 815

Adapter nipple for WSS 1000

Part no.

For connecting WSS 1000 to extension pipe inlet 1⁄4” IT, outlet 9⁄16” – 18 UNF ET 448 204


Part no.

Sand- or abrasive-blasting head with borcarbide focus nozzle, connection 1⁄4” IT, Side-mounted sand supply, connection for shape B nozzle, 15° jet angle nozzle (shape B) not included in scope of supply 418 177Spare borcarbide focus nozzle 430 185

DYNAJET water-sand-blasting accessories

High-pressure nozzles for WSS 500 sand-blasting head


for 150 me 1515 B 425 853 for 280 me + 350 th 15034 B 414 016 for 350 me + 350 mg + 350 md 1505 B 427 144

41



Abrasive suction hose for WSS 500 and WWS 1000

Part no.

For all water-sand-blasting systems with steel spiral inlay (length approx. 12 m) 414 0372x clamps for suction hose required(1x on the spray head WSS and 1x on the suction pipe) 001 422

High-pressure nozzle sets for WSS 1000 sand-blasting head, each set contains 3 nozzles

Machine type Dimensions Shape Part no.

Set for 280 me + 350 th 0.6 E 447 560 Set for 350 me + 350 mg + 350 md 0.7 E 447 561

Nozzle sets for WSS 1000 water-sand-blasting system

Special tools

Part no.

For changing shape E nozzles for the WSS 1000 438 684


Part no.

The abrasive quantity is infinitely adjustable, placed directly in the abrasive material (e.g. in a bucket) 435 113

Abrasives

Part no.

Dynabits (water-soluble special grit for sensitive surfaces and for polishing stainless-steel surfaces), 25 kg 438 929

Other abrasives can be supplied on request

DYNAJET recommendation:Quartz sand (0.20 - 0.60 mm), Slag (0.20 - 0.80 mm or 0.60 - 1.4 mm)

42



DYNAJET surface and floor cleaning accessories

DYNAJET DFS 350 floor cleaning system

Ideal for splash-guard-protected removal and cleaning of surfaces, floors, roads, pavements, etc. at 350 bar (5,075 PSI).

Fully equipped with high-pressure gun, heat-resistant guide rollers, stainless-steel housing, splash guard and hose connection M22 x 1.5 ET for max. 120 °C hot water, nozzle rotor suitable for 2 identical high-speed nozzles (shape D).

Nozzles, sealing rings and support rings are not included in the scope of supply.

Stainless-steel type, permanently rust-resistant 4 steerable wheels, for high versatility Splash guard to reduce environmental pollution Complete with high-pressure spray gun handle in DYNAJET quality Hot-water high-pressure hose Hot-water version for 120 °C, suitable for all DYNAJET machines Large heat and oil-resistant wheels, super smooth running, no jamming Folding handle for easy transportation and space-saving storage Welded stainless-steel nozzle rotor Nozzle carrier for use 2x high-performance nozzles (shape D) Use of nozzles with extremely high efficiency for achieving the very highest

water jet speed and removal performance

Max. pressure 350 bar (5,075 PSI)Max. quantity 50 l/ min (13.23 USgal/ min)Max. temperature 120 °CDiameter 520 mmConnection M22 x 1.5 ETWheels 60 mmNozzle equipment 2x shape DHousing single-walledPart no. 494 302

Spare high-pressure swivelPart no. 501 578

Spare spray gun handlePart no. 444 084

Coupling nut for nozzlePart no. 525 047

Technical data DFS 350/ S

43

21



Suitable for DYNAJET DWS 350 wall cleaning system, with 15° jet angle (Caution: two identical nozzles are always required)


for 280 me + 350 th 1502 B 414 018 for 350 me + 350 mg + 350 md 15028 B 427 823

Nozzle selection for DWS 350

DYNAJET wall cleaning accessories

DYNAJET DWS 350 wall cleaning system

Ideal for hand-guided operation and for cleaning off walls, ceilings and small surfaces, high removal performance when a constant distance is maintained between the nozzleand the object

Fully equipped with spray gun handle, hose connection M22 x 1.5 ET, stainless-steel splash guard with brush and side-mounted handgrip, double-walled with vacuum option via 2” connection, nozzle rotor with connection for 2 identical nozzles (shape A or B), nozzle not included in scope of supply

Part no.

DWS 350/ 3 D (diameter 300 mm, double-walled) 443 314Spare high-pressure swivel 443 633 Spare spray gun handle 444 084

Suitable for DYNAJET DFS 350 floor cleaning system, with optional 15° or 30° jet angle (Caution: two identical nozzles are always required)


15° jet anglefor 280 me + 350 th 0.95 D 498 406 for 350 me + 350 mg + 350 md 1.10 D 498 401

30° jet anglefor 280 me + 350 th 0.95 D 498 393 for 350 me + 350 mg + 350 md 1.10 D 498 394

Nozzle selection for DFS 350


Part no.

(Fig. 1) Sealing ring for shape C and D plug-in nozzles 484 295(Fig. 2) Support ring for shape C and D plug-in nozzles 489 307

44

1 2


DYNAJET roof cleaning accessories

Part no.

Suitable for wave-profile roofs, connection M22 x 1.5 ET, 400 mm diameter 426 846

Fully fitted with brush, pressure gauge, 2⁄2-way manual ball valve for high-pressure on/ off, adjustable distance between wheels, with nozzle rotor for 2 identical nozzles (shape D).

Nozzles, sealing rings and support rings are not included in the scope of supply Part no.

Spare swivel joint 418 362

Part no.

Ideally suited to cleaning concrete or tiled roof tiles, connection M22 x 1.5 ET, 500 mm diameter 546 586

Fully fitted with brush, pressure gauge, 2⁄2-way manual ball valve for high-pressure on/ off, height and distance between wheels can be adjusted to the profile distance, with nozzle rotor for 2 identical nozzles (shape D).

Nozzles, sealing rings and support rings are not included in the scope of supply Part no.

Spare swivel joint 546 587

Suitable for DYNAJET DRS-W and DRS roof cleaning system with optional 15° or 30° jet angle (Caution: two identical nozzles are always required)


15° jet anglefor 280 me + 350 th 0.95 D 498 406for 350 me + 350 mg + 350 md 1.1 D 498 401

30° jet anglefor 280 me + 350 th 0.95 D 498 393for 350 me + 350 mg + 350 md 1.1 D 498 394

Part no. (Fig. 1) Sealing ring for shape C and D plug-in nozzles 484 295(Fig. 2) Support ring for shape C and D plug-in nozzles 489 307


DYNAJET DRS-W roof cleaning system

DYNAJET DRS roof cleaning system

Nozzle selection for DRS and DRS-W


45



DYNAJET pipe and heat exchanger cleaning accessories

Part no.

User-friendly tool for switching the high-pressure on/ off during pipe cleaning (this leaves both hands free for operation), stainless-steel cover, inlet M22 x 1.5 ET, outlet M22 x 1.5 IT, max. 60 l/ min 503 865

Part no.

For connecting the foot valve with pipe cleaning hose, connection M22 x 1.5 ET/ 1⁄4” IT 427 197

Suitable for DYNAJET types up to 350 bar (5,075 PSI) for direct connection via the connction nipple on the F 350 foot valve Part no.

Length 15 m, connection 1⁄4” ET/ 1⁄4” ET, 1⁄4” 414 040 Length 25 m, connection 1⁄4” ET/ 1⁄4” ET, 1⁄4” 414 041 Length 50 m, connection 1⁄4” ET/ 1⁄4” ET, 1⁄4” 414 042

Foot valve F 350

Connection nipple

Pipe cleaning hoses

46

1

2

3


DYNAJET TWS 400 tank washing system

Self-driven rotating high-pressure nozzle head for internal cleaning of containers, vessels, barrels, tanks, etc. with max. 400 bar (5,800 PSI) working pressure, fully equipped with rotor and 2 nozzles (shape A), standard,designed for 350 bar (5,075 PSI) and 21 l/ min (5.56 USgal/ min), connection for hose M22 x 1.5 ET, driven bynozzle reaction force and not by an external energy supply, speed of rotor rotation can be adjusted via the nozzleposition on the rotor

Part no. Aluminium housing 459 469Stainless-steel housing 495 800

DYNAJET container and tank cleaning accessories

DYNAJET TWS 200 tank washing system

Rotating high-pressure nozzle head for internal cleaning of containers, vessels, barrels, tanks, etc. with max. 200 bar (2,900 PSI) working pressure, nozzle head driven by motor.

Parts in contact with water are made of stainless steel, diameter of head 40 mm, shaft length 700 mm, overall length 1,050 mm, weight approx. 25 kg, inlet M22 x 1.5 ET suitable for high-pressure hose, fully equipped with safety valve on the inlet, with 2 high-pressure nozzles, designed for 200 bar (2,900 PSI)working pressure at 21 l/ min (5.56 USgal/ min), various drive motors can be selected for the nozzle head

Part no.

220 V drive 446 917 Pneumatic motor drive 446 918 Water motor drive, no external energy supply required 446 919

Pipe-cleaning nozzles

For direct connection to pipe cleaning hoses, standard nozzle (Fig. 1) for all fields of application, drilled as a pulling nozzle

Machine type Part no.

for 150 me > 30 mm ø, 1⁄4“ IT 414 046 for 280 me + 350 th > 30 mm ø, 1⁄4“ IT 434 659 for 350 me + 350 mg + 350 md > 30 mm ø, 1⁄4“ IT 414 045

Rotating nozzle (Fig. 2) for complete all-round surface cleaning, not available as pulling nozzle


for 280 me + 350 th 30-100 mm ø, 1⁄4” IT (no pulling nozzle, fig. 2) 434 660 for 350 me + 350 mg + 350 md 30-100 mm ø, 1⁄4” IT (no pulling nozzle, fig. 2) 414 049 for 2 x 350 me oder 2 x 350 mg oder 2 x 350 md 30-100 mm ø, 1⁄4” IT (no pulling nozzle, fig. 2) 459 816

Pocking nozzle (Fig. 3) for cleaning completely blocked pipes, drilled as a pulling nozzle


for 150 me > 40 mm ø, 1⁄4” IT 414 048 for 280 me + 350 th > 40 mm ø, 1⁄4” IT 434 661 for 350 me + 350 mg + 350 md > 40 mm ø, 1⁄4” IT 414 047


47

1

3

5

2

4

7 86

2

1


Sludge suction unit + chemical injector

(Fig. 1) Sludge suction unit for sucking up water, sludge, etc. selfmade vacuum, directly connected to a high-pressure hose or cleaning gun, inlet M22 x 1.5 ET, max. 200 bar (2.900 PSI), connection for 1x nozzle (shape B). Nozzle not included in scope of supply! Usage only in combination with flat-jet nozzle 1515 B. Part no.

For DYNAJET 150 me 414 063 Suitable flat-jet nozzle 1515 B (for DYNAJET 150 me) 425 853(Fig. 2) Chemical injector for sucking up cleaning agents using underpressure (only in combination with double-spray wand (Part no. 427 460)) direct connection to unloader valve (only suitable for the DYNAJET trolly types) inlet M22 x 1.5 IT/ outlet M22 x 1.5 ET, adjustable dosing quantity, complete with suction hose, max. 350 bar (5,075 PSI) 445 582

Connectors, quick-release couplings and nipples

Fig. Part no.

M22 x 1.5 ET, 1⁄4” IT 1 427 197 M22 x 1.5 IT, 1⁄4” IT 2 427 587 M22 x 1.5 IT, 1⁄4” ET 3 427 586 M22 x 1.5 IT, 3⁄8” ET 4 427 585 M22 x 1.5 IT, 3⁄8” IT 5 427 534 M22 x 1.5 ET, 3⁄8” IT 6 427 425 M22 x 1.5 ET, 1⁄4” ET 7 428 016 M22 x 1.5 ET, 3⁄8” ET 8 428 017O-ring for quick-release coupling (1, 6-8) 436 797O-ring for quick-release coupling M22 x 1.5 (2-5) 471 538Support ring for quick-release coupling M22 x 1.5 (2-5) 434 458

Hose drum

High-pressure extension hoses for hose drum

Part no.

Loose drum for flexible installation on site, incl. hand crank, high-pressure swivel joint, short hose 0.5 m, fixing plate, inlet M22 x 1.5 ET, outlet M22 x 1.5 ET, for max. 75 m high-pressure hose DN 8 (extension hose not included in scope of supply) 459 309

For hose drum (Part no. 459 309) or trailer (350 th), DN 8, connections 3⁄8” BSP 90° directly on the drum, M22 x 1.5 IT Part no.

Length 25 m 440 603 Length 50 m 440 604 Length 75 m 440 605

Distributing piece

Part no.

For parallel operation of 2 consumers by using 1 DYNAJET machine 1x inlet M22 x 1.5 ET, 2x outlet M22 x 1.5 ET 457 606

Also to use as collecting piece for 2 pumps to 1 consumer (only possible with DYNAJET machines that are equipped with unloader valves without automatic hose pressure drop down-system)

Special accessories


48



Connections via quick-release couplings M24 x 1,5 Part no.

DN 10, length 10 m, connections 2x M24 x 1,5 IT, 120 °C 503 954DN 10, length 25 m, connections 2x M24 x 1,5 IT, 120 °C 503 955DN 10, length 50 m, connections 2x M24 x 1,5 IT, 120 °C 524 382

O-ring for quick-release couplings M24 x 1.5 502 979Support ring for quick-release couplings M24 x 1.5 502 980


Part no. Double nipple for coupling two high-pressure hoses, connections 2x M24 x 1.5 ET, material: stainless steel 502 954Spare O-ring (20 x 2.5) 018 893

Hose connection

High-pressure gun 600

Part no.

Stainless-steel high-pressure gun up to 150 °C with dry-shut-off valve for simple and easyoperation, with minimized hand holding forces, completely insulated, trigger, safety locking system, ideal for work with hot water, overall length approx. 630 mm, side handle can bemounted in various positions, max. 60 l/ min, integrated swivel joint

Hose connection M24 x 1.5 ET, outlet connection M24 x 1.5 IT 546 527

Repair kit for high-pressure cleaning gun 600 546 616O-ring for quick-release couplings M24 x 1.5 546 637Support ring for quick-release couplings M24 x 1.5 546 638

Shoulder support

Part no.

For high-pressure cleaning gun 600, retrofitting possible, rubber cushion on shoulder pad (mandatory with reaction force > 150 Newton) 547 592


49

2

1

3

2.22.1


Part no.

Between the high-pressure cleaning gun 600 and the extension pipe connections M24 x 1.5 ET, 3⁄8” IT, material: stainless steel 502 977Spare O-ring (20 x 2.5) 018 893

Coupling

Extension pipes 3⁄8”, material: stainless steel

Part no.

Length 250 mm, 3⁄8” ET/ 3⁄8” ET, 502 970Length 800 mm, 3⁄8” ET/ 3⁄8” ET, 502 971 Length 1.500 mm, 3⁄8” ET/ 3⁄8” ET, 502 972 Length 2.000 mm, 3⁄8” ET/ 3⁄8” ET, 502 973

DYNAJET recommendation:for safety reasons, you should always select a spray wand of 250 mm or longer, so that when combinedwith high-pressure cleaning gun 600 an overall length of min. 800 mm is reached.

Nozzle carrier for 3⁄8” extension pipes

Part no.

(Fig. 1) For shape A and B nozzles, connection 3⁄8” IT/ 1⁄4 NPT directly to the extension pipe, material: stainless steel 502 974

Teflon sealing tape for sealing shape A and B nozzles 000 306

(Fig. 2) For shape C and D plug-in nozzles, connection 3⁄8” IT directly to the extension pipe 502 952

(Fig. 2.1) Sealing ring for shape C and D plug-in nozzles 484 295(Fig. 2.2) Support ring for shape C and D plug-in nozzles 489 307

(Fig.3) With outlet 1⁄4” ET for rotor nozzles (shape F) up to 500 bar (7,250 PSI) and/ or WSS systems, connection 3⁄8” IT directly to the extension pipe 503 011


50


Rotating nozzles

Adapter

Connection 1⁄4” IT, for connecting to spray wands 3⁄8” adapter Part no. 503 011 is always required, body material: stainless steel (Please note: Always start rotor nozzles downwards. Otherwise the rotor may get damaged.)


500 me + 500 mg + 500 md 030 F 445 940 500 me-27 050 F 466 607 500 th + 500 me-30 055 F 427 149

Flat-jet plug-in nozzles (Shape D)


15° jet angle500 me + 500 mg + 500 md 1.2 D 431 316500 me-27 1.5 D 498 404 500 th + 500 me-30 1.6 D 436 922

30° jet angle 500 me + 500 mg + 500 md 1.2 D 438 676 500 me-27 1.5 D 438 678 500 th + 500 me-30 1.6 D 438 679

High-pressure nozzles

Round-jet plug-in nozzles (shape C)


500 mg + 500 mg + 500 md 1.0 C 438 669 500 me-27 1.3 C 438 673 500 th + 500 me-30 1.4 C 438 675

Repair kits

For rotating nozzles – consisting of a replacement nozzle and ceramic seat, specially designed for the high water temperatures with DYNAJET machines

Machine type Description Part no.

for nozzle 445 940 (Shape F) 030 445 941 for nozzle 466 607 (Shape F) 050 466 666 for nozzle 427 149 (Shape F) 055 431 486

O-ring for all nozzle-sizes 460 442

Part no.

Adapter with outlet 1⁄4” ET for rotor nozzles (shape F) up to 500 bar (7,250 PSI), connection 3⁄8” IT directly to the extension pipe, material: stainless steel 503 011Düsenrohn kpl. 300 mm M24AG – 1⁄4 IG 482 900


51




Part no.

Sand- or abrasive-blasting head with borcarbide focus nozzle connection 1⁄4” IT, side-mounted sand supply, connector for shape B nozzle, 15° jet angle, shape B nozzle not included in scope of supply 418 177

For connecting to extension pipes 3⁄8” adapter Part no. 503 111 is always required

Spare borcarbide focus nozzle for WSS 500 430 185

DYNAJET water-sand-blasting accessories

High-pressure nozzles for WSS 500


500 me + 500 mg + 500 md 1503 B 449 011 500 me-27 1505 B 427 144 500 th + 500 me-30 15055 B 433 537

Part no. Adapter with outlet 1⁄4” ET for WSS system, connection 3⁄8” IT directly to the extension pipe 503 011


Part no.

The abrasive quantity is infinitaly adjustable, placed directly in the abrasive material (e.g. in a bucket) 414 036


Part no.

Professional abrasive-blasting head for continuous use ring-shaped arrangement of the high-pressure nozzles, central abrasive supply, connection 9⁄16”– 18 UNF IT, tungsten carbide focus nozzle, adaptor for shape E high-pressure nozzle (3 pieces), shape E nozzle inserts are not included in the scope of supply 435 111Spare tungsten carbide focus nozzle for WSS 1000 450 815


52



Part no.

The abrasive quanity is infinitaly adjustable, placed directly in the abrasive material (e.g. in a bucket) 435 113


Part no.

For connecting WSS 1000 to extension pipe 3⁄8” inlet 3⁄8” IT, outlet 9⁄16” – 18 UNF ET 506 527

High-pressure nozzle sets for WSS 1000 sand-blasting head, each set contains 3 nozzles

Machine type Size Shape Part no.

Set 500 me + 500 mg + 500 md 0.55 E 453 077 Set 500 th + 500 me-27 + 500 me-30 0.8 E 447 559

Nozzle sets for WSS 1000 water-sand-blasting system

Special tool

Part no.

For replacing shape E nozzles for the WSS 1000 438 684

Abrasive suction hose for WSS 500 + WSS 1000

Part no.

For all water sand blasting systems, with steel spiral inlay (length approx. 12 m) 414 0372x clamps for suction hose required (1x on the spray head WSS and 1x on the suction pipe) 001 422


53


Double spray lance

Part no.

For direct connection to the high-pressure cleaning gun connection M24 x 1.5 ET, length approx. 650 mm, 2 nozzle carriersfor shape B nozzles, infinite regulation of pressure via handgrip, equipped with 1A and B shape low-pressure nozzle (Part no. 506 422) 533 159Spare parts kit for regulating valve 505 583

Flat-jet nozzles shape B

for double spray lance (Part no. 533 159)

Maschine type Description Shape Part no.

15° jet angle (standard) 500 me + 500 mg + 500 md 1503 B 449 011500 me-27 1505 B 427 144 500 th + 500 me-30 15055 B 433 537


Part no.

Dynabits (water-soluble special grit for sensitive surfaces and for polishing stainless-steel surfaces), 25 kg 438 929

Other abrasives can be supplied on request

DYNAJET recommendation:Quartz sand (0.20 - 0.60 mm), Slag (0.20 - 0.80 mm or 0.60 - 1.4 mm)

Abrasives

54


DYNAJET surface and floor cleaning accessories

DYNAJET DFS 500 floor cleaning system

Suitable for DYNAJET floor cleaning system DFS 500, with optional 15° or 30° jet angle (Caution: two identical nozzles are always required)


15° jet anglefor 500 me + 500 mg + 500 md 0.85 D 498 398 for 500 me-27 + 500 th + 500 me-30 1.20 D 431 316

30° jet anglefor 500 me + 500 mg + 500 md 0.85 D 498 391 for 500 me-27 + 500 th + 500 me-30 1.20 D 438 676

Nozzle selection for DFS 500

Max. pressure 500 bar (7,250 PSI)Max. quantity 30 l/ min (7.94 USgal/ min)Max. temperature 120 °CDiameter 520 mmConnection M24 x 1.5 ETWheels 60 mmNozzle equipment 2 x shape DHousing double-wall with suction possibilityPart no. 506 448

Spare high-pressure swivelPart no. 501 579

Spare spray gun handlePart no. 504 032

Technical data DFS 500

Ideal for splash-guard-protected removal and cleaning of surfaces, floors, roads, pavements, etc. at 500 bar (7,250 PSI).

Fully equipped with high-pressure cleaning gun, heat-resistant guide rollers, stainless-steel housing, splash guard and hose connection M24 x 1.5 ET for max. 120 °C hot water, nozzle rotor suitable for 2 identical high-speednozzles (shape D).

Nozzles, sealing rings and support rings are not included in the scope of supply.

stainless-steel type, permanently rust-resistant Double-wall, height adjustable for easy

adaptation to the object surface, possibility for vacuum connection 4 steerable wheels, for high manoeuvrability Splash guard to reduce environmental pollution Complete with high-pressure spray gun handle, in DYNAJET quality Hot-water high-pressure hose Hot-water version for 120 °C, suitable for all DYNAJET machines Large heat and oil-resistant wheels, super smooth running, no jamming Folding frame for ease of transportation and space-saving storage Handle mounted in working position, makes your work easier Nozzle carrier for attaching 2x shape D high-performance nozzles Welded stainless-steel nozzle rotor 90° connection for external vacuum suction possibility Use of nozzles with extremely high efficiency for achieving the very highest water jet speed and removal performance


55

1 2


Foot valve F 500

Part no.

User-friendly tool for switching the high-pressure on/ off during pipe cleaning (this leaves both hands free for operation), stainless-steel cover, inlet M24 x 1.5 ET, outlet M24 x 1.5 ET 532 373

DYNAJET pipe cleaning accessories (use for diameter approx. 30-100 mm)

DYNAJET pipe and heat exchanger cleaning accessories

Coupling

Part no.

Between high-pressure hose and adapter nipple,connections M24 x 1.5 ET, 3⁄8” ET 502 978


Part no.

DN 10, length 10 m, connection 2x M24 x 1.5 IT 503 954 DN 10, length 25 m, connection 2x M24 x 1.5 IT 503 955DN 10, length 50 m, connection 2x M24 x 1.5 IT 524 382

Adaptor nipple

Part no.

between coupling and pipe-cleaning nozzle inlet 3⁄8” IT, outlet 1⁄4” ET 503 011


Part no.

(Fig. 1) Sealing ring for shape C and D plug-in nozzles 484 295(Fig. 2) Support ring for shape C and D plug-in nozzle 489 307


56

1

2


DYNAJET heat-exchanger cleaning accessories (use for diameter approx. 12-25 mm)

Coupling

Adapter nipple

Part no. Between foot valve F 500 and adapter nipple (Art.-Nr. 455 117), inlet M24 x 1,5 IT, outlet 3⁄8” IT 502 975

Part no.

Between hose connection (Part no. 502 975) and flexible lance, inlet 3⁄8” ET, outlet M24 x 1.5 DKO ET 445 117

Flexible lances

Inlet for hose connection M24 x 1.5 DKO IT, length 10 m, with marking before the hose end

Outside diameter Connection thread Type Part no.

10.5 mm M7 ET (4/2) 505 57113 mm 1⁄8” ET (5/2) 505 57416 mm 1⁄4” ET (6/2) 505 576


Rigid design, drilled as pulling nozzle with front jet, suitable for DYNAJET 500 me-27, 500 me-30 and 500 th

Outside diameter Connection thread Suitable for type Part no.

10.5 mm M7 IT (4/2) 505 57712 mm 1⁄8” IT (5/2) 505 57816 mm 1⁄4” IT (6/2) 505 579

Rotating, drilled as pulling nozzle with front jet, suitable for DYNAJET 500 me-27, 500 me-30 and 500 th


10.5 mm M7 IT (4/2) 505 58013 mm 1⁄8” IT (5/2) 505 58118 mm 1⁄4” IT (6/2) 505 582


For direct connection to pipe cleaning hoses, standard nozzle (Fig. 1) for all fields of application, drilled as a pulling nozzle Machine type Part no.

for 500 me + 500 mg + 500 md > 30 mm ø, 1⁄4” IT, 15 l 467 183 for 500 me-27 + 500 th + 500 me-30 > 30 mm ø, 1⁄4” IT, 30 l 427 074

Rotating nozzles (Fig. 2) for complete, all-round cleaning, no pulling nozzle


for 500 me + 500 mg + 500 md 30-100 mm ø, 11⁄4” IT, 15 l 485 667 for 500 me-27 + 500 th + 500 me-30 30-100 mm ø, 1⁄4” IT, 30 l 427 073


57

4

1 2

3


Special DYNAJET accessories

Connectors and quick-release couplings

Fig. Part no.

M24 x 1,5 ET, 3⁄8” IT 1 502 977 M24 x 1,5 IT, 3⁄8” IT 2 502 975M24 x 1,5 IT, 3⁄8” ET 3 502 976M24 x 1,5 ET, 3⁄8” ET 4 502 978

Sealing ring for quick-release coupling M24 x 1.5 502 979Support ring for quick-release coupling M24 x 1.5 502 980O-ring for M24 x 1.5 ET, 20 x 2.5 (for 1 and 4) 018 893.005

High-pressure gun 600 short

Part no.

Single spray gun handle, stainless-steel type, with servo dry-shut-off for simple and easy operation, inlet M24 x 1.5 ET, outlet 3⁄8” IT 504 032Repair kit for high-pressure gun 502 434

Hose drum

High-pressure hose for hose drum

Part no.

Loose drum for installation on site, complete with hand crank, high-pressure swivel joint, fixing plate, inlet M24 x 1.5 ET, outlet M24 x 1.5 ET, suitable for max. 50 m high-pressure hose DN 10, short hose piece (approx. 0.5 m) included 532 960Hose line, short, approx. 0.5 m, with 90° angle and M24 x 1.3 IT 459 593

Part no.

For hose drum (Part no. 532 960) or trailer (500 th), DN 10, connections 3⁄8” BSP 90° directly to the drum, outlet M24 x 1.5 IT, 50 m 503 956


58



Distribution piece

Part no.

For parallel operation of 2 operators by using 1 DYNAJET machine 1x inlet M24 x 1.5 ET, 2x outlet M24 x 1.5 ET 523 638

Also to use as a connecting piece for 2 pumps to 1 consumer (only possible with DYNAJET machinesthat are equipped with unloader valves without automatic hose pressure drop down-system)

59


Until the end of 2008, the DYNAJET machines within the 500 bar (7.250 PSI) pressure range were supplied with M22 x 1.5 connections and extension pipes with a diameter of 1⁄4” .

Since the start of 2009, however, all DYNAJET machines within the 500 bar (7.250 PSI) pressure range are now sup-plied as standard with pressure outlets, quick-release cou-plings, etc. in a M24 x 1.5 version and with extension pipes with a diameter of 3⁄8”.

The overview to the right includes the options for joining and coupling the M22 x 1.5 connections to the current M24 x 1.5 size.

Connection options M22–M24

M22 x 1,5 IT Adapter M22 ET - M22 ET M22 x 1,5 IT Part no. 427 518



M22 x 1,5 IT Adapter M22 ET - M24 IT M24 x 1,5 ET Part no. 532 939

M24 x 1,5 IT Adapter M24 ET - M22 IT M22 x 1,5 ET Part no. 532 940

M24 x 1,5 IT Adapter M24 IT - M22 IT M22 x 1,5 ET

M24 ITPart no. 502 975

M22 ITPart no. 427 585

60

➁

120° ➀

➂

90° ➀➁

➂➁


Part no.

DN 10, length 10 m, connections 2x M24 x 1.5 DKO IT, 100 °C 477 853 DN 10, length 20 m, connections 2x M24 x 1.5 DKO IT, 100 °C 482 089

Spare O-ring 485 381

High-pressure hose lines

Part no.

As double nipple for coupling of two high-pressure hoses, Connections 2x M24 x 1.5 DKO ET, PN 1,800 bar 437 756

Hose connection



Part no.

For user-friendly operation, prevents twisting of the hose-lines, installed directly between the high-pressure cleaning gun and the high-pressurehose line, connections M26 x 1.5 ET (high-pressure gun connection) and M24 x 1.5 DKO ET (hose connection), PN 1,600 bar (23,200 PSI), max. 95 °C 494 275

Swivel joint

➀ Ideal water direction change with minimised loss in velocity and pressure➁ Increased safety, through a reduction in forces on the wrist, i.e. ideal power

transmission without torque being felt on the middle of the hand➂ Extension pipe can be infinitely rotated through 360° against the handgrip,

i.e. increased flexibility and safety (high-pressure hose swirl decoupling)

DYNAJET Standard

➀ Sharp-edged direction change with loss in velocity and pressure losses➁ Increased holding forces for operator, cross forces create torque on the wrist, i.e. tiring more quickly, less safety➂ Rigid connection, no flexibility, hose line creates

torque on the extension pipe

The DYNAJET high-pressure gun/ lance system

Distribution piece

Part no.

For parallel operation of 2 operators by using 1 DYNAJET pump 1x inlet M24 x 1.5 DKO ET, 2x outlet M24 x 1.5 DKO ET 533 163

61



High-pressure gun 1200 complete assembled with extension pipe

Part no.

Servo trigger for easy operation, dry shut gun with mechanical valve, increased safety via central power transmission in the handgrip without cross forces, infinite rotation of extension pipe to the handgrip, safety trigger with lock to prevent unintentional opening, inlet M24 x 1.5 DKO ET, incl. extension pipe approx. 800 mm, hand protection and nozzle carrier for shape C and D nozzles, nozzles not included. 522 605

Version for DYNAJET 800 me and 800 th wireless

Part no.

Identical to Part no. 522 605, but additionally with electronic contact switch (initiator) for remote control, complete with short piece of cable and metal plug. 514 730

Version for DYNAJET 800 th

High-pressure gun 1200, single

Part no.

With servo trigger and mechanical dry shut valve inlet M24 x 1.5 DKO ET, outlet M26 x 1.5 IT 522 604Set of seals 1,200 bar (17,400 PSI) 0-ring/support rings 539 484Special tool for disassembly 528 283

Part no.

High-pressure gun 1200 with servo trigger, mechanical dry shut valve and electric contact switch (initiator) for remote control, inlet M24 x 1.5 DKO ET, outlet M26 x 1.5 IT 514 731Spare contact switch (initiator) with cable piece and metal plug 512 224Repair kit for high-pressure gun 1200 489 339Set of seals 1,200 bar (17,400 PSI) 0-ring/support rings 539 484Special tool for disassembly 528 283

62

1 2


Part no.

Suitable for high-pressure gun 1200, for absorbing reaction forces (mandatory with reaction force > 150 Newton) 519 001

Shoulder support

High-pressure extension pipes

Direct fixation to the high-pressure gun 1200, outside diameter 14.3 mm, spanner flat 12 mm on both sides,threaded connection on both sides 9⁄16”-18 UN-LH ET, PN 1,600 bar (23,200 PSI), internal diameter 8 mm Part no.

Length 350 mm 482 505 Length 800 mm 482 515 Length 1,200 mm 482 516 Length 2,000 mm 482 517

DYNAJET recommendation:For safety reasons, you should always select a spray wand of 800 mm or longer, so that when combined with the high-pressure cleaning gun 1200, an overall length of min. 800 mm is reached.

Pressure ring and pressure screw

Part no.

(Fig. 1) Pressure ring for screwing on ultrahigh-pressure connections, slot version to prevent unintentional loosening of the connection through vibrations, thread 9⁄16”-18 UNF-LH IT 474 636(Fig. 2) Pressure screw for screwing on ultrahigh-pressure connections, anti-vibration type combined with pressure ring, thread M26 x 1.5 ET 474 635

Side-handgrip

Part no.

For mounting on the side of the extension pipe, adjustable in any position 519 707

Protective handle

Part no. For surrounding and protecting the extension pipe 489 336


63

15°

40°

60°

15°

30°

15°

40°

60°

15°

30°

21


Remote control cable

Part no.

To fix 1x plug-in nozzle insert (shape C or D), consisting of 1x basic body, 1x union nut, PN 1,500 bar (21,750 PSI), connection 9⁄16”-18 UNF-LH IT,extremely light in weight, complete with sealing ring and support ring, nozzle not included in scope of supply 488 299

Part no.

(Fig. 1) Sealing ring for plug-in nozzles (shape C and D) 484 295(Fig. 2) Support ring for plug-in nozzle (shape C and D) 489 307

Nozzle carrier (shape C and D)

Sealing ring and support ring for nozzle insert (shape C and D)

Nozzle insert (shape C) = round-jet nozzle

Round-jet nozzle as nozzle insert, material: stainless steel, vacuum-hardened, seal via sealing ring (Part no. 484 295) and support ring (Part no. 489 307), field of application up to 1,500 bar (21,750 PSI)


800 me, 800 th, 800 th wireless ø 1.0 mm C 438 669

Nozzle insert (shape D) = flat-jet nozzle

Flat-jet nozzle as nozzle insert, material: stainless steel, vacuum-hardened, seal via sealing ring (Part no. 484 295) and support ring (Part no. 489 307), field of application up to 1,500 bar (21,750 PSI)


800 me, 800 th, 800 th wireless (jet angle 15°) ø 1.2 mm D 431 316800 me, 800 th, 800 th wireless (jet angle 30°) ø 1.2 mm D 438 676

For accessories and tools with remote control via electrical contact or proximity switch, metal plug Part no.

Length 25 m, loose, with coupling and plug 511 694 Length 50 m, loose, with coupling and plug 511 696Length 25 m, on drum, with socket and plug 514 733Length 50 m, on drum, with socket and plug 514 734


64


Rotating “Turbo” type nozzle

To be fitted directly on the extension pipe, without brake, with high speed rotationfor quick surface preparation, connection 9⁄16” – 18 UNF-LH IT, max. 80 °C


800 me (30° jet angle) ø 1.05 mm F 528 432 800 th, 800 th wireless (30° jet angle) ø 1.10 mm F 435 110 Repair kit for rotating nozzles (shape F) – consisting of replacement nozzle pin and seat,specially designed for DYNAJET machines


800 me (for nozzle Part no. 528 432) ø 1.05 mm F 528 434 800 th + 800 th wireless (for nozzle Part no. 435 110) ø 1.10 mm F 443 326

Water-sand-blasting system WSS 1000

Part no. Professional abrasive-blasting head for continuous use ring-shaped arrangement of the high-pressure nozzles, central abrasive supply, connection 9⁄16”– 18 UNF IT,tungsten carbide focus nozzle, adaptor for shape E high-pressure nozzle (3 pieces), shape E nozzle inserts are not included in the scope of supply 435 111 Spare tungsten carbide focus nozzle for WSS 1000 450 815

Rotations-Düsen-System RDS-Easy 1000-2

Part no.

Universal rotating nozzle system self-driven via reaction force, speed adjustment via contact-free magnetic brakes approx. 1,000-2,000 rpm, weighs only approx. 1.2 kg, nozzle carrier head with 27° to fix max. 2 shape C nozzle inserts, connection 9⁄16”-18 UNF-LH IT, nozzle inserts not included in scope of supply, max. 1,000 bar (23,200 PSI) 544 806

DYNAJET recommendation for standard equipping Part no.

800 me 2x 0,70 447 556800 th, 800 th wireless 2x 0,75 546 322


65


Abrasive suction hose for WSS

Part no.

For all water sand blasting systems, with steel spiral inlay (length approx. 15 m) 414 0372x clamps for suction hose required (1x on the spray head WSS and 1x on the suction pipe) 001 422.001

High-pressure nozzle sets for WSS 1000 sand-blasting head, consisting of 3 nozzles

Machine type Size Shape Part no.

800 me, 800 th, 800 th wireless ø 0.6 mm E 447 560

Nozzle set for WSS 1000 water-sand-blasting system

Special tool

Part no.

For replacing shape E nozzles for the WSS 1000 438 684

Tank washing system TWS 1000

Part no.

For cleaning the interior of tanks/ mixer drums, containers and enclosures of various types 461 074

three-dimensional cleaning using a nozzle rotor with two high-pressure nozzles (800 bar (11,600 PSI), 21 l/ min (5.56 USgal/ min) design) driven by reaction force of the water jet speed of rotation regulated by a magnetic brake

complete with hose connections M24 x 1.5 DKO ET


Part no.

The abrasive quanity is infinitaly adjustable, placed directly in the abrasive material (e.g. in a bucket) 435 113


66


Foot valve F1200

Flexible lances

Part no.

Identical with F1200, but with signal contact (initiator) for remote control, complete with short cable and metal plug 514 755

For DYNAJET 800 th

Part no.

Complete with mechanical dry shut valve via foot switch, inlet M24 x 1.5 DKO ET, outlet M24 x 1.5 DKO ET, suitable for a maximum temperature of 95 °C 532 110

For DYNAJET 800 me and 800 th wireless

Part no.

Spare contact switch (initiator) with cable piece and metal plug 512 224 Repair kit for F1200 489 339

Connection M24 x 1.5 DKO IT, length 10 m, with a marking before the hose end

Outside diameter Connection thread Type Part no.

10.5 mm M7 ET (4/2) 505 57113 mm 1⁄8” ET (5/2) 505 57416 mm 1⁄4” ET (6/2) 505 576


67



DYNAJET floor cleaning system DFS 1200

Surface cleaner for large-area and quick removal or cleaningof surfaces of any kind

Removal diameter approx. 260 mm, PN 1,200 bar (17,400 PSI), complete with 4 large stable wheels, connection M24 x 1.5 DKO ET, with nozzle rotor for shape G nozzles, initiator for remote control, connector socket for remote control cable, suitable for hot water use, robust and solid industrial design, driven by nozzle reaction force

Nozzles not included in scope.

Part no.

DFS 1200 without vacuum connection 505 584DFS 1200 with vacuum connection 505 585

Rigid design, drilled as pulling nozzle


10.5 mm M7 IT (4/2) on request13 mm 1⁄8” IT (5/2) 538 77316 mm 1⁄4” IT (6/2) 538 799

Rotating, drilled as pulling nozzle


10.5 mm M7 IT (4/2) on request13 mm 1⁄8” IT (5/2) 538 77416 mm 1⁄4” IT (6/2) 538 806


Picture shows version with vacuum connection

68

www.dynajet-online.comAccessories up to 1,200 bar (17.400 PSI)

Part no.

Lance for PN 3,000 bar (43,500 PSI) with electric contact via proximity switch, short cable and metal plug, pressure ringand pressure screws not included, safety trigger with lock to prevent unintentional opening, connections 2x M26 x 1.5 IT 514 732

Further information see page 60.

Spare contact switch (initiator) with cable piece and metal plug 512 224

Connection on both sides M24 x 1.5 DKO IT, cone nipple with O-ring,connector and nut made of rust-resistant steel, 4 reinforcement layers of spiralsteel wire, PN 1,200 bar (17,400 PSI), outer layer is made of polyamide Part no. Diameter 10 mm, length 10 m 477 156Diameter 10 mm, length 20 m 477 157


Part no.

For connecting 2 high-pressure hose lines connections 2x M24 x 1.5 DKO ET, material: stainless steel 437 756

Part no.

For user-friendly operation, prevents twisting of the hose-lines, installed directly between the high-pressure spray wand and the high-pressure hose line, connections M26 x 1.5 ET (spray lance connection) and M24 x 1.5 DKO ET(hose connection), PN 1,600 bar (23,200 PSI), max. 95 °C 494 275

Part no.

For spray lance SL 3000, inlet M24 x 1.5 DKO ET, outlet to lance M26 x 1.5 ET 494 900

Part no.

Between connection nipple (Part no. 494 900) and SL 3000 (Part no. 514 732) 526 635

Hose connection

Swivel joint

Connection nipple

Sealing ring

Spray lance SL3000

Accessories up to 1,200 bar (17.400 PSI)

Part no.

Suitable for high-pressure lance, for absorbing reaction forces (mandatory with reaction force > 150 Newton) 519 001

Shoulder support


69

21



Direct fixation to the high-pressure cleaning lance, outside diameter 14.3 mm, spanner flat 12 mm on both sides, threaded connection on both sides 9⁄16”-18 UNF-LH ET, PN 1,600 bar (23,200 PSI), internal diameter 8 mm Part no. Length 800 mm 482 515 Length 1,200 mm 482 516 Length 2,000 mm 482 517

DYNAJET recommendation:for safety reasons, you should always select a spray wand of 800 mm or longer, so that whencombined with the spray lance SL 3000, an overall length of approx. 800 mm is reached.

Protective handle

Part no.

As protection for the extension pipe 489 336

Pressure ring and pressure nut

Part no.

(Fig. 1) Pressure ring for screwing on ultrahigh-pressure connections, slot version to prevent unintentional loosening of the connection through vibrations, thread 9⁄16”-18 UNF-LH IT 474 636(Fig. 2) Pressure nut for screwing on ultrahigh-pressure connections, anti-vibration type when combined with pressure ring, thread M26 x 1.5 ET 474 635



Length 25 m, loose, with coupling and plug 511 694 Length 50 m, loose, with coupling and plug 511 696 Length 25 m, on drum, with socket and plug 514 733Length 50 m, on drum, with socket and plug 514 734

Side-handgrip

Part no.

For mounting on the extension pipe, adjustable in any position 519 707


70

www.dynajet-online.comAccessories up to 1,200 bar (17.400 PSI)

Nozzle carrier (shape G)

Foot switch

Part no.

Complete with proximity switch (initiator) for remote control with short cable and metal plug. No valve inside! 514 756Spare contact switch (initiator) with cable piece and metal plug 512 224

Rotating "Turbo" type nozzle

Part no.

Flexible multi-purpose nozzles, self-driven with nozzle reaction force for extremely hard spot jet, the ideal combination of surface treatment and removal, for nearly all fields of application, PIN insert can be replaced, connection 9⁄16”-18 UNF-LH IT, rotor d= 1.25 (designed and calculated for 1,200 bar (17,400 PSI) at 32 l/ min (8.47 USgal/ min)) 438 683Repair kit for rotating nozzle (Part no. 438 683), rotor d= 1.25 441 249

Nozzle insert (shape G)

Round-jet nozzle with outside thread M 10 and hexagon socket, screw material:stainless steel, nozzle insert with intake cone made of vacuum-hardened stainless steel,metallic seal 59° made from bronze, use up to 3,000 bar (43,500 PSI)


DYNAJET UHP 170, 1,200 bar ( 17,400 PSI)/ 40.5 l/min ø 1.2 mm 498 183

Part no.

To fix 1 shape G nozzle insert, M10 internal thread, PN 2,800 bar (40,600 PSI), connection 9⁄16”-18 UNF-LH IT, extremely light-weight 482 783

Part no.

High-pressure rotating nozzle system up to 3,000 bar (43,500 PSI), leak-free, multi-spray head self-driven via reaction force, speed adjustment via contact-free magnetic brakes approx. 1,000 - 2,500 rpm, weighs only approx. 1.8 kg, nozzle carrier head to fix max. 3 shape G nozzle inserts (M10), connection 9⁄16”-18 UNF-LH IT, nozzle inserts not included in scope of supply 544 735

Available diameters for shape G nozzle inserts: see pages 78/ 79.

DYNAJET recommendation for standard UHP units:

DYNAJET UHP 170, 1,200 bar (17,400 PSI)/ 31 l/min (8,19 USgal/min): 3x nozzle insert shape G, ø 0.70 mm 3x Part no. 457 459

Rotating nozzle system RDS-Easy 3000-3

71

87

1211

56

345 6

10

1

9

2

1

2


Flexible lances

Use for inside cleaning of small pipes or heat exchanger tubes Part no.

Connections M24 x 1.5 DKO IT, M7 ET for pipe-cleaning nozzles, outside diameter 12 mmInternal diameter 4 mm, length 6 m 482 370Internal diameter 4 mm, length 12 m 482 371

Connections M24 x 1.5 DKO IT, G 1⁄4” ET for pipe-cleaning nozzles, outside diameter 15 mmInternal diameter 6 mm, length 6 m 482 865Internal diameter 6 mm, length 12 m 482 879Internal diameter 6 mm, length 25 m 482 880

Pipe and heat exchanger cleaning nozzles

Nozzles on request

(Fig. 1) rigid design, drilled as pulling nozzle (Fig. 2) rotating, drilled as pulling nozzle

Part no.

1,200 bar (17,400 PSI) Basic 498 0061,200 bar (17,400 PSI) Power 498 007

Equipment consists of: Fig.

1x Spray lance SL3000 with hose connection M24x1.5 ET 11x Shoulder support 21x High-pressure extension pipe 800 mm 31x Side handgrip 41x Pressure screw 51x Pressure ring 61x Nozzle carrier for shape G nozzle 71x Round-jet nozzle (shape G) 8 1x Remote control cable 25 m, loose 9 1x High-pressure hose, 20 m, DN 10, PN 1,200 bar (17,400 PSI) 10 1x Antiseize paste for lubricating metallic threaded connections 1x Rotating nozzle system RDS-Easy 3000-3* 113x Round-jet nozzle (shape G) for RDS-Easy-3000-3* 12

* included only in the package “1,200 bar (17,400 PSI) Power” (Part no. 498 007)

DYNAJET high-pressure accessories set for 1,200 bar (17,400 PSI)

72

1

2

3

4

5

6

1

1

1

3

4

3

1

6

6 5

2

www.dynajet-online.comAccessories up to 3,000 bar (43,500 PSI)


With sealing nipple for quick connect system Easy Connect EC, protective tubing included with burst protection. Part no.

2,000 bar, DN8, length 20 m 526 5392,800 bar, DN5, length 5 m 526 536 2,800 bar, DN8, length 10 m 526 5373,000 bar, DN8, length 20 m 539 725

O-ring for sealing nipple EC 526 356Support ring for sealing nipple EC 526 357

Part no.

Hose connector EC, DN5 und DN8 526 352

Safety coupling for hose connector EC, hoses DN5 and DN8 526 351 Safety coupling EC for pump/ lance connection, DN5 und DN8 526 353

Connection nipple EC for pump and lance-side M26 x 1.5 ET 526 354

Protection cap for hose nipple EC 526 355

New high-pressure hoses and quick connect system = Easy Connect EC for 3,000 bar (43,500 PSI)

Terms:

Easy, fast, safe Pressure range up to 3,000 bar (40,600 PSI), DN5 and DN8 Less single parts Turnable if system is pressureless. Replaces rotary joints No tools required, means massive time

savings = EC (Easy Connect) Stringent safety: If assembled incorrectly it

will not work Burst pressure of the couplings is considerably higher than that of the hose System achieves all valid safety standards

Advantages:

Less wear of components, no threaded unions and no “sticking” possible Faster assmebly time, saving valuable job time Easiest handling and ergonomic design Hose twisting eliminated – longer hose life Operator protection assured Few parts, small stock and nearly no wear and tear parts



73

21


Pressure ring and pressure screw


Part no.

(Fig. 1) Pressure ring for screwing on ultrahigh-pressure connections, slot version to prevent unintentional loosening of the connection through vibrations, thread 9⁄16”-18 UNF-LH IT 474 636(Fig. 2) Pressure screw for screwing on ultrahigh-pressure connections, anti-vibration type when combined with pressure ring, thread M26 x 1.5 ET 474 635


Length 25 m, loose, with coupling and plug 511 694 Length 50 m, loose, with coupling and plug 511 696 Length 25 m, on drum, with socket and plug 514 733Length 50 m, on drum, with socket and plug 514 734


Direct fixation to the high-pressure cleaning lance, outside diameter 14.3 mm, spanner flat 12 mm on both sides, threaded connection on both sides 9⁄16”-18 UNF-LH ET, PN 3,200 bar (46,400 PSI), internal diameter 5 mm Part no.

Length 350 mm 482 518Length 800 mm 482 519 Length 1,200 mm 482 520 Length 2,000 mm 482 521

DYNAJET recommendation:For safety reasons, you should always select a spray wand of 800 mm or longer, so that whencombined with the spray lance SL 3000, an overall length of min. 800 mm is reached.

Part no.

Lance for PN 3,000 bar (43,500 PSI) with electric contact via proximity switch, short cable and metal plug, pressure ring and pressure screws not included, safety trigger with lock to prevent unintentional opening, connections 2x M26 x 1.5 IT . Further information see page 60. 514 732Spare contact switch (initiator) with cable piece and metal plug 512 224

Spray lance SL 3000

Part no.

Suitable for spray lance for absorbing reaction forces (mandatory with reaction force > 150 Newton) 519 001

Shoulder support


74

10

13

56

8

9

3 7412

5 6

11

12


DYNAJET high-pressure accessories set as “Basic package”

Part no.

2,000 bar (29,000 PSI) Basic 533 1112,800 bar (40,600 PSI) Basic 533 098


1x Spray lance SL3000 with EC connection 11x Shoulder support 2 1x High-pressure extension pipe 800 mm 31x Side handgrip 41x Pressure screw 51x Pressure ring 61x Nozzle carrier for shape G nozzle 72x Round-jet nozzle (shape G) 8, 9 1x Remote control cable 25 m, loose 10 1x Antiseize paste for lubricating metallic threaded unions 1x Adapter for safety coupling 111x Safety coupling for pump/lance connection 121x High-pressure hose EC, 20 m, DN 8, PN 2,000 bar (29,000 PSI) with hose protection 13 or1x High-pressure hose EC, 20 m, DN 8, PN 2,800 bar (40,600 PSI) with hose protection 13

Complete accessory package, suitable for DYNAJET UHP 170 types,complete with a selection of suitable nozzle equipment


75

10

15

56

8

9

11 12

3 7412

5 6

13

14


DYNAJET high-pressure accessories set as “Power package”

Part no.

2,000 bar (29,000 PSI) Power 533 1122,800 bar (40,600 PSI) Power 533 099


1x Spray lance SL3000 with EC connection 11x Shoulder support 21x High-pressure extension pipe 800 mm 31x Side handgrip 41x Pressure nut 51x Pressure ring 61x Nozzle carrier for shape G nozzle 72x Round-jet nozzle (shape G) 8, 9 1x Remote control cable 25 m, loose 10 1x Rotating nozzle system RDS-Easy 3000-6 116x Round-jet nozzle (shape G) for RDS-Easy 3000-6 121x Antiseize paste for lubricating metallic threaded unions1x Adapter for safety coupling 131x Safety coupling for pump/lance connection 141x High-pressure hose EC, 20 m, DN 8, PN 2,000 bar (29,000 PSI) with hose protection 15 or1x High-pressure hose EC, 20 m, DN 8, PN 2,800 bar (40,600 PSI) with hose protection 15

Complete accessory package, suitable for DYNAJET UHP 170 types, equipment identical to "Basic package", however in addition it comes with rotating nozzle system RDS-Easy 3000-6


76




Rotating "Turbo" type nozzle

Part no.

High-performance rotating nozzle system up to 3,000 bar (43,500 PSI), leak-free, multi-spray head self-driven via reaction force, speed adjustment via contact-free magnetic brakes approx. 1,000 – 4,000 rpm, weighs only approx. 1.8 kg, nozzle carrier head to fix max. 3 shape G nozzle inserts (M10), connection 9⁄16”-18 UNF-LH IT, nozzle inserts not included in scope of supply 544 735

Available diameters for shape G nozzle inserts see pages 78/ 79.


DYNAJET UHP 170, 2,000 bar (29,000 PSI)/ 23.5 l/min (6,22 USgal/min): 3x nozzle insert shape G, ø 0.50 mm 3x Part no. 455 458DYNAJET UHP 170, 2,800 bar (40,600 PSI)/ 18 l/min (4,76 US gal/min):3x nozzle insert shape G, ø 0.40 mm 3x Part no. 454 982

Part no.

High-performance rotating nozzle system up to 3,000 bar (43,500 PSI), leak-free, multi-spray head self-driven via reaction force, speed adjustment via contact-free magnetic brakes approx. 1,000 - 4,000 rpm, weighs only approx. 1.8 kg, nozzle carrier head to fix max. 3 shape G nozzle inserts (M10), connection 9⁄16”-18 UNF-LH IT, nozzle inserts not included in scope of supply 544 736

Available diameters for shape G nozzle inserts see pages 78/ 79.


DYNAJET UHP 170, 2,000 bar (29,000 PSI)/ 23.5 l/min (6,22 USgal/min): 6x nozzle insert shape G, ø 0.35 mm 6x Part no. 455 457DYNAJET UHP 170, 2,800 bar (40,600 PSI)/ 18 l/min (4,76 US gal/min):6x nozzle insert shape G, ø 0.30 mm 6x Part no. 457 454

Part no.

Flexible multi-purpose nozzle only for max. 2,500 bar (36,250 PSI), self-driven via reaction force for an extremely hard spot jet, the ideal combinationof surface treatment and removal, for nearly all fields of application, PIN insert can be replaced, connection 9⁄16”-18 UNF-LH IT, rotor diameter 0.9 mm (designed and calculated for UHP 170, 2,000 bar (29,000 PSI), 23.5 l/ min(6.22 USgal/ min)) 497 304Repair kit for rotating nozzle (Part no. 497 304), rotor ø 0.9 mm 497 310

Side-handgrip

Part no.

For mounting on the extension pipe, adjustable in any position 519 707


77


Nozzle insert (shape G)

Part no.

To fix 1 shape G nozzle insert, M10 internal thread, PN 3,000 bar (40,600 PSI), connection 9⁄16”-18 UNF-LH IT, extremely light-weight 482 783

DYNAJET floor cleaning system DFS 2800

Surface cleaner for large-area and quick removal or cleaningof surfaces of any kind

Removal diameter approx. 260 mm, PN 2.800 bar (40,600 PSI), complete with 4 large stable wheels, connection 9⁄16” - 18 UNF LH, with nozzlerotor for shape G nozzles, initiator for remote control, connector socket for remote control cable, robust and solid industrial design, driven by nozzle reaction force

Nozzle inserts not included in scope of supply. Part no.

DFS 2800 without vacuum connection 528 551DFS 2800 with vacuum connection 528 591

DYNAJET recommendation for standard equipping:

DYNAJET UHP 170, 2,800 bar (40,600 PSI)/ 18 l/min: 2x nozzle insert shape G, 0.25 mm 2x Part no. 454 9794x nozzle insert shape G, 0.30 mm 4x Part no. 457 454

Nozzle carrier (shape G)

Round-jet nozzle with outside thread M 10 and hexagon socket, screw material:stainless steel, nozzle insert with intake cone made of vacuum-hardened stainless steel,metallic seal 59° made from bronze, use up to 3,000 bar (43,500 PSI)


DYNAJET UHP 170, 2,000 bar (29,000 PSI)/ 23.5 l/ min (6,22 USgal/ min) ø 0.90 mm 492 799DYNAJET UHP 170, 2,800 bar (40,600 PSI)/ 18 l/ min (4,76 USgal/ min) ø 0.70 mm 457 459


The picture shows version with vacuum connection

78

1

3

4

6

10

98

6 7

5

2


Accessory recommendation for DYNAJET UHP 170, 2.800 bar (40,600 PSI), 18 l/min

Nozzle chart for DYNAJET ultra high-pressure jet nozzles shape G

Part no. Ø mm

Operating pressure (bar)

Part no. Ø mm300 400 500 600 700 800 900 1,000 1,100 1,200 1,300 1,400 1,500 1,600 1,700 1,800 1,900 2,000 2,100 2,200 2,300 2,400 2,500 2,800 3,000

Flow rate l/min

455 459 0.00* - - - - - - - - - - - - - - - - - - - - - - - - - 455 459 0.00*

457 453 0.20 0.42 0.49 0.55 0.60 0.65 0.69 0.74 0.78 0.81 0.85 0.88 0.92 0.95 0.98 1.01 1.04 1.07 1.10 1.12 1.15 1.18 1.20 1.23 1.30 1.34 457 453 0.20

454 979 0.25 0.66 0.77 0.86 0.94 1.01 1.08 1.15 1.21 1.27 1.33 1.38 1.43 1.48 1.53 1.58 1.63 1.67 1.71 1.76 1.80 1.84 1.88 1.92 2.03 2.10 454 979 0.25

457 454 0.30 0.96 1.10 1.23 1.35 1.46 1.56 1.68 1.75 1.83 1.91 1.99 2.06 2.14 2.21 2.28 2.34 2.41 2.47 2.53 2.59 2.65 2.70 2.76 2.92 3.02 457 454 0.30

455 457 0.35 1.30 1.50 1.68 1.84 1.99 2.12 2.25 2.38 2.49 2.60 2.71 2.81 2.91 3.00 3.10 3.19 3.27 3.36 3.44 3.52 3.60 3.68 3.76 3.97 4.11 455 457 0.35

454 982 0.40 1.70 1.96 2.19 2.40 2.60 2.77 2.94 3.10 3.25 3.40 3.54 3.67 3.80 3.92 4.04 4.16 4.28 4.39 4.50 4.60 4.70 4.81 4.91 5.19 5.37 454 982 0.40

457 455 0.45 2.15 2.48 2.78 3.04 3.28 3.51 3.72 3.93 4.12 4.30 4.48 4.65 4.81 4.97 5.12 5.27 5.41 5.55 5.69 5.82 5.95 6.08 6.21 6.57 6.80 457 455 0.45

455 458 0.50 2.65 3.07 3.43 3.75 4.08 4.34 4.60 4.86 5.08 5.31 5.53 5.74 5.94 6.13 6.32 6.50 6.68 6.66 7.02 7.19 7.35 7.51 7.66 8.11 8.40 455 458 0.50

457 456 0.55 3.21 3.71 4.15 4.54 4.91 5.25 5.56 5.87 6.15 6.43 6.69 6.94 7.18 7.42 7.65 7.87 8.08 8.29 8.50 8.70 8.90 9.09 9.27 9.81 10.16 457 456 0.55

457 457 0.60 3.82 4.41 4.94 5.41 5.84 6.24 6.62 6.98 7.32 7.65 7.96 8.26 8.55 8.83 9.10 9.36 9.62 9.87 10.12 10.35 10.59 10.81 11.04 11.68 12.09 457 457 0.60

457 458 0.65 4.49 5.18 5.79 6.35 6.85 7.33 7.77 8.19 8.59 8.97 9.34 9.69 10.03 10.36 10.68 10.99 11.29 11.59 11.87 12.15 12.42 12.69 12.95 13.71 14.19 457 458 0.65

457 459 0.70 5.20 8.01 6.72 7.36 7.95 8.50 9.01 9.50 9.96 10.41 10.83 11.24 11.64 12.02 12.39 12.75 13.10 13.44 13.77 14.09 14.41 14.72 15.02 15.90 16.46 457 459 0.70

457 460 0.75 5.97 6.90 7.71 8.45 9.12 9.75 10.35 10.91 11.44 11.95 12.44 12.90 13.36 13.80 14.22 14.63 15.03 15.42 15.80 16.18 16.54 16.90 17.24 18.25 18.89 457 460 0.75

457 461 0.80 6.80 7.85 8.77 9.61 10.38 11.10 11.77 12.41 13.01 13.59 14.15 14.68 15.20 15.70 16.18 16.65 17.10 17.55 17.98 18.41 18.82 19.22 19.62 20.76 21.49 457 461 0.80

492 798 0.85 7.67 8.86 9.91 10.85 11.72 12.53 13.29 14.01 14.69 15.35 15.97 16.58 17.16 17.72 18.27 18.79 19.31 19.81 20.30 20.78 21.25 21.70 22.15 23.44 24.26 492 798 0.85

492 799 0.90 8.60 9.93 11.11 12.17 13.14 14.05 14.90 15.71 16.47 17.20 17.91 18.58 19.23 19.87 20.48 21.07 21.65 22.21 22.76 23.29 23.82 24.33 24.83 26.28 27.20 492 799 0.90

492 800 0.95 9.58 11.07 12.37 13.65 14.64 15.65 16.60 17.50 18.35 19.17 19.95 20.70 21.43 22.13 22.82 23.48 24.12 24.75 25.36 25.95 26.54 27.11 27.67 29.28 30.31 492 800 0.95

498 179 1.00 10.62 12.28 13.71 15.02 16.22 17.34 18.39 19.39 20.34 21.24 22.11 22.94 23.75 24.53 25.28 26.01 26.73 27.42 28.10 28.76 29.41 30.04 30.66 32.44 33.58 498 179 1.00

498 180 1.05 11.71 13.62 15.12 16.56 17.88 19.12 20.28 21.38 22.42 23.42 24.37 25.29 26.18 27.04 27.87 28.68 29.47 30.23 30.98 31.71 32.42 33.12 33.80 35.77 37.03 498 180 1.05

498 181 1.10 12.85 14.84 16.59 18.17 19.63 20.98 22.26 23.46 24.61 25.70 26.75 27.76 28.73 29.66 30.59 31.48 32.34 33.18 34.00 34.80 35.58 36.35 37.09 39.26 40.64 498 181 1.10

498 182 1.15 14.04 16.22 18.13 19.86 21.45 22.93 24.33 25.64 26.89 28.09 29.24 30.34 31.40 32.43 33.43 34.40 35.35 36.26 37.16 38.03 38.89 39.72 40.54 42.91 44.41 498 182 1.15

498 183 1.20 15.29 17.66 19.74 21.63 23.36 24.97 26.49 27.92 29.28 30.59 31.83 33.04 34.20 35.32 36.40 37.46 38.49 39.49 40.46 41.41 42.34 43.25 44.15 46.72 48.36 498 183 1.20

*Blind nozzle Reaction force < 150 N Freehand operation allowed.

Reaction force 150 N - 250 NFreehand operation permitted only if used with

shoulder support.(Part no. 519 001).

Reaction force > 250 NFreehand operation prohibited.

Nozzle/ lance have to be guided or supported mechanically.

79


Nozzle insert shape G

M10 connection with sealing cone

Other diameters on request.

Part no. Ø mm

Operating pressure (bar)

Part no. Ø mm300 400 500 600 700 800 900 1,000 1,100 1,200 1,300 1,400 1,500 1,600 1,700 1,800 1,900 2,000 2,100 2,200 2,300 2,400 2,500 2,800 3,000

Flow rate l/min

455 459 0.00* - - - - - - - - - - - - - - - - - - - - - - - - - 455 459 0.00*

457 453 0.20 0.42 0.49 0.55 0.60 0.65 0.69 0.74 0.78 0.81 0.85 0.88 0.92 0.95 0.98 1.01 1.04 1.07 1.10 1.12 1.15 1.18 1.20 1.23 1.30 1.34 457 453 0.20

454 979 0.25 0.66 0.77 0.86 0.94 1.01 1.08 1.15 1.21 1.27 1.33 1.38 1.43 1.48 1.53 1.58 1.63 1.67 1.71 1.76 1.80 1.84 1.88 1.92 2.03 2.10 454 979 0.25

457 454 0.30 0.96 1.10 1.23 1.35 1.46 1.56 1.68 1.75 1.83 1.91 1.99 2.06 2.14 2.21 2.28 2.34 2.41 2.47 2.53 2.59 2.65 2.70 2.76 2.92 3.02 457 454 0.30

455 457 0.35 1.30 1.50 1.68 1.84 1.99 2.12 2.25 2.38 2.49 2.60 2.71 2.81 2.91 3.00 3.10 3.19 3.27 3.36 3.44 3.52 3.60 3.68 3.76 3.97 4.11 455 457 0.35

454 982 0.40 1.70 1.96 2.19 2.40 2.60 2.77 2.94 3.10 3.25 3.40 3.54 3.67 3.80 3.92 4.04 4.16 4.28 4.39 4.50 4.60 4.70 4.81 4.91 5.19 5.37 454 982 0.40

457 455 0.45 2.15 2.48 2.78 3.04 3.28 3.51 3.72 3.93 4.12 4.30 4.48 4.65 4.81 4.97 5.12 5.27 5.41 5.55 5.69 5.82 5.95 6.08 6.21 6.57 6.80 457 455 0.45

455 458 0.50 2.65 3.07 3.43 3.75 4.08 4.34 4.60 4.86 5.08 5.31 5.53 5.74 5.94 6.13 6.32 6.50 6.68 6.66 7.02 7.19 7.35 7.51 7.66 8.11 8.40 455 458 0.50

457 456 0.55 3.21 3.71 4.15 4.54 4.91 5.25 5.56 5.87 6.15 6.43 6.69 6.94 7.18 7.42 7.65 7.87 8.08 8.29 8.50 8.70 8.90 9.09 9.27 9.81 10.16 457 456 0.55

457 457 0.60 3.82 4.41 4.94 5.41 5.84 6.24 6.62 6.98 7.32 7.65 7.96 8.26 8.55 8.83 9.10 9.36 9.62 9.87 10.12 10.35 10.59 10.81 11.04 11.68 12.09 457 457 0.60

457 458 0.65 4.49 5.18 5.79 6.35 6.85 7.33 7.77 8.19 8.59 8.97 9.34 9.69 10.03 10.36 10.68 10.99 11.29 11.59 11.87 12.15 12.42 12.69 12.95 13.71 14.19 457 458 0.65

457 459 0.70 5.20 8.01 6.72 7.36 7.95 8.50 9.01 9.50 9.96 10.41 10.83 11.24 11.64 12.02 12.39 12.75 13.10 13.44 13.77 14.09 14.41 14.72 15.02 15.90 16.46 457 459 0.70

457 460 0.75 5.97 6.90 7.71 8.45 9.12 9.75 10.35 10.91 11.44 11.95 12.44 12.90 13.36 13.80 14.22 14.63 15.03 15.42 15.80 16.18 16.54 16.90 17.24 18.25 18.89 457 460 0.75

457 461 0.80 6.80 7.85 8.77 9.61 10.38 11.10 11.77 12.41 13.01 13.59 14.15 14.68 15.20 15.70 16.18 16.65 17.10 17.55 17.98 18.41 18.82 19.22 19.62 20.76 21.49 457 461 0.80

492 798 0.85 7.67 8.86 9.91 10.85 11.72 12.53 13.29 14.01 14.69 15.35 15.97 16.58 17.16 17.72 18.27 18.79 19.31 19.81 20.30 20.78 21.25 21.70 22.15 23.44 24.26 492 798 0.85

492 799 0.90 8.60 9.93 11.11 12.17 13.14 14.05 14.90 15.71 16.47 17.20 17.91 18.58 19.23 19.87 20.48 21.07 21.65 22.21 22.76 23.29 23.82 24.33 24.83 26.28 27.20 492 799 0.90

492 800 0.95 9.58 11.07 12.37 13.65 14.64 15.65 16.60 17.50 18.35 19.17 19.95 20.70 21.43 22.13 22.82 23.48 24.12 24.75 25.36 25.95 26.54 27.11 27.67 29.28 30.31 492 800 0.95

498 179 1.00 10.62 12.28 13.71 15.02 16.22 17.34 18.39 19.39 20.34 21.24 22.11 22.94 23.75 24.53 25.28 26.01 26.73 27.42 28.10 28.76 29.41 30.04 30.66 32.44 33.58 498 179 1.00

498 180 1.05 11.71 13.62 15.12 16.56 17.88 19.12 20.28 21.38 22.42 23.42 24.37 25.29 26.18 27.04 27.87 28.68 29.47 30.23 30.98 31.71 32.42 33.12 33.80 35.77 37.03 498 180 1.05

498 181 1.10 12.85 14.84 16.59 18.17 19.63 20.98 22.26 23.46 24.61 25.70 26.75 27.76 28.73 29.66 30.59 31.48 32.34 33.18 34.00 34.80 35.58 36.35 37.09 39.26 40.64 498 181 1.10

498 182 1.15 14.04 16.22 18.13 19.86 21.45 22.93 24.33 25.64 26.89 28.09 29.24 30.34 31.40 32.43 33.43 34.40 35.35 36.26 37.16 38.03 38.89 39.72 40.54 42.91 44.41 498 182 1.15

498 183 1.20 15.29 17.66 19.74 21.63 23.36 24.97 26.49 27.92 29.28 30.59 31.83 33.04 34.20 35.32 36.40 37.46 38.49 39.49 40.46 41.41 42.34 43.25 44.15 46.72 48.36 498 183 1.20

*Blind nozzle Reaction force < 150 N Freehand operation allowed.

Reaction force 150 N - 250 NFreehand operation permitted only if used with

shoulder support.(Part no. 519 001).

Reaction force > 250 NFreehand operation prohibited.

Nozzle/ lance have to be guided or supported mechanically.

Complete equipment for well prepared construction site use

Description Fig. Part no.

1x 20 m supply hose, 1 446 914 3⁄4” connections, 2x Geka coupling 1x Storage drum 2 446 926 for supply hose 1x Mobile filter station with parallel principle for maximum 3 494 706 filter area within the smallest space 1x Filter insert package, 4 496 575 2 x 80 my stainless steel, 6x 10 my micro filter and 2m connection hose 1x 20 m high-pressure hose, 5 539 725 with Easy Connect quick coupling, DN8 to keep pressure loss to a minimum 2x Easy Connect hose connector 6 526 352 and safety coupling 6 526 351

Description Fig. Part no.

1x 5m working hose, DN5, for flexible 7 526 536 and trouble-free operation with the lance 1x Accessory kit “Power” with rotating nozzle 8 533 099 and 1x 25 m cable as well as 1x 20 m high-pressure hose DN8 1x Additional extension pipe 9 482 519 for quick tool change, as well as 1 pressure ring 474 636 and 1 pressure screw 474 635 1x Extension control cable, 10 514 734 50 m on drum

80

www.dynajet-online.comPersonal protective equipment

Personal protective equipment (PPE)

Protective suit

Poratex Premium, 100% waterproof, 2-piece (jacket + overalls), without protective function against high-pressure Part no.

Medium 414 067 Large 414 068 X-Large 414 069 XX-Large 414 070

Overalls

As protection against dirt, 100% waterproof, with cap and neck ruff, without protective function against high-pressure Part no.

Large 426 895 X-Large 426 896

"Speedy" protective goggles

Part no.

Made from scratch-proof colourless polycarbonate sheet, with length-adjustable wings 414 094

Sizing information for ordering protective clothing:

Order size S (Small) Body size 158 – 170 cm Chest circumference 80 – 92 cmOrder size M (Medium) Body size 170 – 182 cm Chest circumference 92 – 104 cmOrder size L (Large) Body size 182 – 188 cm Chest circumference 104 – 116 cmOrder size XL (X-Large) Body size 188 – 194 cm Chest circumference 116 – 124 cmOrder size XXL (XX-Large) Body size 194 – 200 cm Chest circumference 124 – 132 cm

81

Personal protective equipment

Clothing for protection against ultrahigh-pressure

* The protective clothing is certified in accordance with Regulation 89/ 686/ EEC and BGR 191

Overalls*

As protection against high-pressure, 100 % waterproof, different protection rates available

Part no.

up to 1,000 bar (14,500 PSI) spot jet, 2,800 bar (40,600 PSI) rotor nozzleMedium (size S – M) 460 752 Large (size L – XL) 460 753 X-Large (size XXL) 460 754

up to 2,000 bar (29,000 PSI) spot jet, 3,000 bar (43,500 PSI) rotor nozzleMedium (size S – M) 460 747 Large (size L – XL) 460 300 X-Large (size XXL) 460 748

Safety vest*

For protection against high-pressure, 100% waterproof,in different types for different protection-pressure ranges Part no.

up to 1,000 (14,500 PSI) spot jet, 2,800 bar (40,600 PSI) rotor nozzle(size M-XXL) 460 756 up to 2,000 bar (29,000 PSI) spot jet, 3,000 bar (43,500 PSI) rotor nozzle(size M-XXL) 460 302

High-pressure apron*

easy to put on and take off Part no.

up to 500 bar (7,250 PSI) rotor nozzle and flat-jet nozzle and 200 bar (2,900 PSI) spot-jet nozzleweight 1.5 kg 546 668 up to 2,000 bar (29,000 PSI) spot jet – 3,000 bar (43,500 PSI) rotor nozzle weight 1.7 kg, one size 476 881

82

www.dynajet-online.comPersonal protective equipment

Gloves

Lined, 100 % waterproof, breathable, heat-resistant, without protection function for high-pressure Part no.

Size 8 414 086 Size 9 414 087 Size 10 414 088 Size 11 414 089

Safety shoe covers*

With clips for securely fastening them over your regular safety boots, for protection against ultrahigh-pressure, very comfortable and light to wear, one size fits all Part no. Version designed for 1,000 bar (14,500 PSI) spot jet, 2,800 bar rotor nozzle 460 757 Version designed for 2,000 bar (29,000 PSI) spot jet, 3,000 bar rotor nozzle 460 306

Hand/ arm protection*

For high-pressure protection, for right or left hand/ arm available, one size fits all Part no.

Hand/ arm protection – left hand:Version designed for 1,000 bar (14,500 PSI) spot jet, 2,800 bar rotor nozzle 460 759 Version designed for 2,000 bar (29,000 PSI) spot jet, 3,000 bar rotor nozzle 460 760

Hand/ arm protection – right hand:Version designed for 1,000 bar (14,500 PSI) spot jet, 2,800 bar rotor nozzle 460 762 Version designed for 2,000 bar (29,000 PSI) spot jet, 3,000 bar rotor nozzle 460 307

* The protective clothing is certified in accordance with Regulation 89/ 686/ EEC and BGR 191

83

Personal protective equipment

Safety boots 800 / 3000

Certified according to inspection basis EN 345-1 – June 1997, BGR 191, Section 3.1.5.5.3 (trade association regulations and rules for health and safety at work – use of foot and legprotection) by approved and authorised centre no. 0299

Safety boots 800 for use when working with manually-operated high-pressure cleaners,can resist a pressure of up to 800 bar (11,600 PSI) and a lance reaction force of up to 117 N, for a nozzle size of up to 1.0 mm, with up to 75 mm distance between the nozzle and the boots, and a feed rate of up to 0.2 m/ sec and water flow rate of up to 17.7 l/ min (4.68 USgal/ min) Part no.

Size 42 460 736 Size 43 460 737 Size 44 460 738 Size 45 460 739 Size 46 460 740

Safety boots 3000 for use when working with manually-operated high-pressure cleaners, can resist a pressure of up to 3,000 bar (43,500 PSI), (comply with BGR 191 and EN 345-1 99A-5 S5). Part no.

Size 42 499 649 Size 43 499 650 Size 44 499 651 Size 45 499 652 Size 46 499 653Size 47 499 654 Size 48 499 655

Safety helmet

Part no.

Incl. ear protection, visor and anti-fog visor (polycarbonate), types conform with CE, EN 397: 1195, EN 352-3 427 305 Additional stainless steel visor 546 664 Replacement polycarbonate visor 546 665 Spare ear protection 546 666

84

www.dynajet-online.comGeneral accessories

General accessories

Pressure gauge

Part no.

For supply side, 0-10 bar, for monitoring the suction pressure, inlet for GEKA coupling, outlet for GEKA coupling 001 160

Part no.

PN 10 bar, 3⁄4” (DN 19), length of 20 m, 2x GEKA coupling 446 914

Supply hose

Part no.

Suitable for: max. 25 m, DN 8 high-pressure hose max. 25 m, DN 10 high-pressure hosemax. 20 m, 3⁄4” (DN 19) supply hose 446 926Hose drum with hole + handlemax. 10 m DN 10 rubber hosemax. 20 m DN 8 rubber hose 476 796

Storage drum

GEKA quick-release couplers for water and air hoses with 3⁄8”– 11⁄4” NW (V)

Part no.

Sealing, GEKA plus 413 895 Sealing 002 313ET 3⁄4” 001 386 ET 1” 062 815 ET 11⁄4” 062 861 IT 3⁄4” 002 311IT 1” 001 391IT 11⁄4” 062 622


85

General accessories

Additional filter

Aqua Soft liquid softener ASFE 2000

Antiseize lubricant

For supply side GEKA coupling inlet, GEKA coupling outlet, filter insert made of VA stainless steel, filter insert mesh size 80 μm, loose delivery Part no.

Body size 5” 460 418Body size 9 3⁄4” 532 306

Filter insert 5”, material VA stainless steel, 80 μm 495 841Filter insert 9 3⁄4”, material VA stainless steel, 80 μm 495 982

Highly concentrated liquid softener, protects all heating elementsin contact with water against calcification Part no.

1 litre 482 923 10 litres 497 086

Protects against damage and seizing in the threaded unions of stainless-steel connections Part no.

Tube 30 g 505 919Tin 500 g 498 633Spray 400 ml 533 138


Extension cable

Case

Part no.

15 M, 400 V, 50 HZ, 6 h, 32 A, 5 x 6 2 430 51730 M, 400 V, 50 HZ, 6 h, 32 A, 5 x 6 2 430 51810 M, 400 V, 50 HZ, 6 h, 63 A, 5 x 16 2 466 26825 M, 400 V, 50 HZ, 6 h, 63 A, 5 x 16 2 466 26950 M, 400 V, 50 HZ, 6 h, 63 A, 5 x 16 2 466 270

Part no.

Document case for A4 format 211 800

86

80 μm VA

80 μm VA

10 μm/50 μm

10 μm/50 μm

www.dynajet-online.comGeneral accessories

For universal use with all high-pressure cleaning unitsin the DYNAJET family

Robust aluminium type to minimise weight, corrosion-resistant Large filter surface and universal filter unit that can be adjusted to the type of dirt and machine type to ensure the highest flexibility on site Having replacement filters available on-site keeps changing times to a minimum Using a short hose, the filter unit is directly connected before the supply line of the high-pressure cleaning tool and protects the machine Increased working times through large filter surfaces in 2x2 parallel operation with minimised pressure loss at the same time 2x2 filter housing 9 3⁄4” in parallel connection* Robust design with 2 carrying handles 3-leg frames with solid rubber feet for reliable stability Covering plate made of aluminium Storage space for 4 replacement filter inserts Connection 3⁄4” GEKA coupling, outlet 3⁄4” GEKA coupling 2x cover coupling Stainless-steel filter inserts can be washed out

Filter inserts not included in standard scope of supply.

Mobile DYNAJET filter station

21

*Funct. principle for parallel connection:

Possible filter inserts:

Type Fineness Dimensions Part no.

Depth filter (Fig. 1) 10 μm TF 9 3⁄4” 496 557Depth filter (Fig. 1) 50 μm TF 9 3⁄4” 494 759Stainless steel (Fig. 2) 80 μm VA 9 3⁄4” 495 982

Inserts for filter box

Equipment concept for accessory filter packages, consists of: Part no.

Accessory package 1 with 6x depth filters 10 μm TF, 2x stainless-steel filter 80 μm VA, 2 m supply hose 496 575Accessory package 2 with 6x depth filters 50 μm TF, 2x stainless-steel filter 80 μm VA, 2 m supply hose 496 576

Filter station accessory packages


Max. supply pressure 8 bar (116 PSI) at 20 °CMax. temperature 50 °C at 3 bar (43.5 PSI)Max. volumetric flow rate 40 l/ min (10.6 USgal/ min)Weight approx. 11 kgDimensions (L x W x H) 435 x 340 x 404 mmPart no. 494 706

Technical data Filter station

87

General accessories

DYNAJET hose catcher

Part no.

As safety protection when manually cleaning the interior of pipes and heat exchangers with flexible lances and hoses, fastened universally by using clamps, safety plate, storage compartment for various inserts, suitable for heat exchanger cleaning lances type 4/2, 5/2, 6/2 505 570

Protects the operator in case of nozzle return or hose failure.

Hose catcher safety system in use at site, mounted on a heat exchanger


88


DYNAJET – we’re always where you need us

In addition to its three locations in Germany, France and Denmark, DYNAJET provides a global service network in coo-peration with its partners. This means that we can offer you our professional DYNAJET service and know-how throug-hout the world.

For further information about DYNAJET or our worldwide service network, simply visit us at www.dynajet.de or contact us at one of our locations – we looking forward to hearing from you:

DYNAJET Germany

DYNAJET GmbH Max-Eyth-Strasse 10 72631 Aichtal Germany

Tel + 49. (0) 71 27. 5 99 - 618 Fax + 49. (0) 71 27. 5 99 - 9671

DYNAJET France

DYNAJET Bureau de liaison50 Avenue d‘Alsace 68025 Colmar France

Tel + 33. (0) 3. 89 20 43 - 90 Fax + 33. (0) 3. 89 20 43 - 79

DYNAJET Denmark

DYNAJET A/S Fabriksvej 3 5580 Nørre Aaby Denmark

Tel + 45. (0) 40 45. 80 89Fax + 49. (0) 71 27. 5 99 - 9671

89

Robust, efficient and powerful high-pressure cleaners for the construction industry DYNAJET provides the ideal professional high-pressure cleaner for all cleaning and construction projects. From normal dirt to not-so-common encrustations, our devices simply offer a clean solution – regardless of whether you have to clean construction equipment, scaffolding and shuttering, or remove road markings.

Sustainable and flexible renovation work with DYNAJETWhere high-pressure technology is to be used for renovations, DYNAJET’s water jetting systems are the ideal partners. Whether it’s simple facade renovation or problematic concrete restoration, surface preparation and roughening of old layers of concrete are child’s play with DYNAJET.

Efficient and economical – DYNAJET for local authoritiesDYNAJET offers suitable high-pressure cleaners for local authorities in particular, guaranteeing optimum cleaning of public areas even where budgets are tight. Pedestrian precincts, steps, pavements, buildings, parks or cemeteries: with DYNAJET, everything can be taken care of very quickly, thoroughly and economically.

Professional and reliable high-pressure cleaners for shipyards and offshore applicationsDYNAJET is always the right choice, even for the most stubborn dirt: from cleaning and renovating entire harbour and oil-drilling installations, to cleaning containers and warehouses, right through to treating ships in dry dock, with DYNAJET high-pressure cleaners, all tasks are carried out rapidly, thoroughly and reliably.

With DYNAJET, industrial facilities look cleanWith DYNAJET, small and large production plants are cleaned with high pressure and at very high speed. Offering out-standing performance and the perfect accessories for all conceivable applications, DYNAJET water jetting systems are the best guarantee for “just-in-time” solutions.

For agriculture and forestry – DYNAJET, naturallyModern forestry and agriculture relies on DYNAJET. Our high-pressure cleaners are particularly successful in removing earth, loess soil and loam from tractors, agricultural machinery and devices. Another ideal application for DYNAJET’s water jetting systems is the gentle removal of bark from trees.

DYNAJET in action – efficient, flexible and economical

90


I. Scope of Application1. The following terms and conditions apply to all deliverables of DYNAJET GmbH (hereinafter referred to as the

"Supplier"), regardless of whether the respective contract is a sales contract, a contract for work and services or another contractual relationship.

2. By placing an order, the buyer, principal or customer (hereinafter referred to as the "Customer") agrees to the terms and conditions of sale and delivery below. If Customer confirms the order as being subject to its own purchasing terms and conditions only, such terms and conditions are hereby objected to. With acceptance of our goods or approval for dispatch at the latest, our terms and conditions are deemed accepted.

3. The Suppliers product offering is intended for entrepreneurs exclusively. Entrepreneur means a person or legal entity or a non-incorporated firm having legal capacity who acts in a commercial or self-employed capacity when entering into the contract (§ 14 Sec. 1 BGB [German civil Code]).

II. Conclusion of Contract, Modifications, Assignment1. The documents which are a part of the offer (e.g., images, drawings) as well as information about the scope of

delivery, appearance, performance, dimensions, weight, consumption of operating materials, operating costs, etc., are approximate values only, unless it has expressly been designated as binding. The Supplier retains rights of ownership and copyrights to any cost estimates, drawings and other documents. They must not be made available to third parties and shall be returned upon request.

2. The goods offered in the Supplier's webshop are non-binding. By placing an order in the webshop, Customer make a binding offer for concluding a contract of purchase for the respective product. Customer is bound by its offer until the lapse of the fifth day from the working day following the day of the offer.

3. The contract shall be deemed concluded when the Supplier has confirmed acceptance of the order in writing (by letter, facsimile, E-mail, etc.) or has commenced delivery or performance If the Supplier has submitted an offer which is subject to a time limit, the contract shall be deemed concluded when the Customer has submitted written acceptance of the offer in due time.

4. Oral secondary agreements at conclusion of the contract and amendments to the contract shall not become effective until the Supplier has confirmed them in writing. Obvious spelling or calculation errors may be cor-rected retroactively.

5. Customer must not assign its rights from this contract. However, § 354a HGB [German commercial code] shall remain unaffected.

III. Prices1. Prices are stated ex works, including loading in the works, but excluding packaging, plus statutory value-added

tax in conformity with the applicable provisions of the country of delivery or performance. If the Supplier's com-pensation has not been agreed bindingly, the Supplier’s prices in effect on the day of delivery shall apply.

2. Engineering work, installation and commissioning will be billed separately. Such billing may be calculated at either a flat rate or according to actual expenditure, plus travel costs, subsistence allowance and overnight expenses, overtime, surcharges for Sundays and public holidays.

3. If at the request of the Customer the Supplier is willing to make an exchange, the Supplier is entitled to bill the incurred costs, no less, however, than the amount of the loss in value resulting from aging and use, plus 10.0 % of the agreed price of the originally agreed object of the delivery, as compensation for the expenditures incurred by the Supplier due to the exchange. The Supplier may not demand the flat-rate cost compensation described in the above provision if the Customer proves that no or only minor damage or expenditure has been incurred by the Supplier.

IV. Payment, Default in Payment, Set-Off, Retention1. In the absence of deviating agreements, payment for the delivery of machines shall become due within 7 days

from delivery, for spare parts within 30 days and for services within 14 days from date of invoice without any deductions. Orders from our webshop (www.dynajet.de) will be executed against prepayment only (in the way stated in the order form) or by cash on delivery (COD), in each case against invoice (which is sent by E-mail and which may be included in our order acknowledgement). At Customer's request, which must be stated in the order form, we also deliver the goods against payment in cash at our premises in Aichtal, Max-Eyth-Str. 10.

2. Any and all outstanding receivables shall become due and payable immediately – even if an extension or other deferral of payment has been granted – if the Customer is in default of payment for more than 5 workdays, in whole or in part, as regards its payment obligations towards the Supplier or if circumstances arise which substantially reduce the creditworthiness of the Customer (e.g., deterioration of assets, delay or cessation of payments, excess debt, downgrading of creditworthiness by commercial credit insurers, protesting of bills of exchange and cheques, filing of a petition for institution of insolvency proceedings or the institution or dismis-sal thereof). In this case, the Supplier may refuse further deliveries or performance and request the provision of reasonable security for its claims.

3. Payment by bill of exchange is subject to special agreement. Bills of exchange and cheques will only be accepted subject to redemption. The Customer shall bear any collection and discount charges. No cash discount will be granted for payment by bill of exchange or in the event of overdue payments, even if such a discount has otherwise been agreed.

4. The Customer may offset Supplier’s claims solely against undisputed or non-appealable claims. The Customer has a right of retention only if its counterclaim is based on the same contractual relationship and is undisputed or non-appealable, or if the Supplier has grossly violated its obligations under the same contractual relation-ship. However, this provision applies without prejudice to the right of the Customer to retain a reasonable part of the purchase price for defects in the Supplier’s performance.

5. If the Customer suffers deterioration in assets in the meaning of No. IV. 2., the Supplier may withdraw from the contract if an appropriate period granted for providing security through the Customer has lapsed unsuccessful-ly. This provision applies without prejudice to further statutory claims of the Supplier, e.g., damages. Damage claims of the Customer are excluded in such case

V. Delivery Time, Partial Delivery or Performance, Default in Acceptance, Withdrawal of Supplier, Supplier's Damage Claims

1. Delivery and installation periods do not commence until the Supplier and the Customer have reached an agreement on all details of the performance and all terms and conditions of the transaction and the Supplier has confirmed the order. Said periods shall be suspended as long as the Customer is in arrears with its duties to cooperate under the contract (e.g., provision of documents, supply of materials, permits, releases) or an agreed advance payment.

2. The delivery time shall be deemed met if the object of the delivery has left the works or if notification of readi-ness for shipping has been made before the lapse of such period.

3. The delivery time shall be extended reasonably in the event of force majeure, strike, lock-out and other extraordi-nary circumstances that are beyond the Supplier's control; this provision shall also apply if a supplier of the Supplier is affected, to the extent that these circumstances can be proven to have an influence on the delivery time.

4. If the Supplier’s performance is delayed, it shall not be in default of performance if such delay is caused by circumstances which could reasonably not be foreseen, prevented or overcome by taking reasonable measures.

5. The Supplier is entitled to withhold its performance until the Customer fulfils its obligations towards the Supplier under this or another contract or for another legal ground.

6. Partial performance is admissible to the extent that it is reasonable for the Customer. Such partial performance shall each be deemed an independent legal transaction which may be bill separately.

7. If the terms of payment are not observed, delivery not accepted in due time or acceptance thereof is refused or if security which has been agreed or is due in accordance with No. IV.2. has not been provided, the Supplier shall be entitled to withdraw from the contract and to claim damages after a reasonable period of extension has lapsed fruitlessly.

8. If at the request of the Customer the dispatch is delayed, the Supplier may bill either the storage and mainte-nance costs actually incurred or a flat rate in the amount of 1/2 % of the invoice amount per month; the latter, however, is not permitted if the Customer proves that the Supplier incurred no or only minor damage or expen-diture. This does not affect the Customer’s payment obligations

VI. Transfer of Risk, Shipping and Acceptance1. The risk shall pass to the Customer no later than at the time of dispatch of the object of delivery. This provision

shall also apply to partial performance or if the Supplier bears the costs of shipping or installation or under-takes delivery itself. No liability is accepted for the most favourable freight charges or transport time.

2. If delivery, shipping or acceptance of the object of delivery is delayed by the Customer due to no fault of the Supplier, all risks – including the risk of deterioration or loss of the object of delivery, as well as all risks resul-ting from the object itself – shall pass to the Customer with notification of readiness for shipping or completion.

3. Upon written request, the shipment will be insured at the Customer’s expense, with the coverage requested by it.

4. The Customer is liable for any and all damage caused by it through negligence during or prior to acceptance of the object of delivery (e.g., sampling, any acceptance procedure to be performed, etc.).

5. Delivered objects shall be accepted by the Customer, even if they are defective, without prejudice to its rights.

VII. Complaint of Defects, Warranty, Warranty Period1. The Customer shall examine the object of the delivery immediately after receipt and lodge written complaint

about any defects without delay. The Customer shall also examine the object of delivery for defects each time before use, in particular regarding safety and suitability for use During its use, the object of delivery shall be monitored constantly with regard to safety and defects. If there are even slight concerns regarding its suitability for use or safety, the object must not be used or its operation must be stopped immediately. The Supplier shall be notified in writing immediately, specifying the concerns or defects by way of a complaint about defects. The Customer shall allow the Supplier the time and opportunity required to perform any and all repairs or replacement deliveries which the Supplier deems necessary.

2. If the Supplier’s performance is poor at the time of the transfer of risk, the Supplier shall remedy the faults, in its own discretion by remedying the defects or delivering a fault-free object in exchange for the defective one. Replaced parts become the property of the Supplier. If remedying a defect for which the Supplier is responsible is not possible, has finally failed, is unreasonable for the purchaser, or if the Supplier has refused both remedy options, or if a reasonable extension of the period granted for remedying has lapsed fruitlessly, the Customer, in its own discretion, may reduce the remuneration for the Supplier or withdraw from the contract. If the defect is of a minor nature only, however, the Customer's only right is the reduction of remuneration. Any damage claims of Customer are subject to items VIII.5, VIII.6 and VIII.7.

3. If the Supplier has fraudulently concealed a defect or has given a guarantee for the quality of the object, the statu-tory regulations shall apply.

4. Unauthorized remedying of defects through the Customer or third parties shall result in the loss of all claims for defects towards the Supplier. The Supplier will not bear the costs for any remedy of defects by the Customer or third parties, unless the express prior consent of the Supplier has been obtained. This provision does not apply in urgent cases – including but not limited to circumstances where a delay is impossible – where the operating safety is at risk or to prevent unreasonably great damage. In such cases, the Supplier shall be notified immedia-tely and shall be obligated to reimburse the necessary costs only.

5. The Supplier does not accept any warranty or liability for damage that is caused by the following: Unsuitable or improper use, defective installation or commissioning by the Customer or third parties, natural wear and tear, including but not limited to wear and tear of parts that are in contact with water, defective or negligent handling, improper maintenance, excessive use, unsuitable operating materials, including but not limited to poor water quality and replacement materials, poor work, unsuitable foundation, chemical, electro-technical/electronic or electric influences. This exclusion does not apply if the Supplier is responsible for the damage in conformity with the more specific provisions in VIII. No. 5. The Supplier also accepts no liability or responsibility for, including but not limited to, the following measures and actions taken by the Customer or third parties and the consequences thereof: Improper remedy of defects, modification of the object of delivery without the prior consent of the Supplier, addition and insertion of parts, including but not limited to spare parts which have not been supplied by Supplier or which the Supplier has not expressly approved, and failure to adhere to the operating instructions and manual.

6. The Supplier does not accept any warranty for material provided by the Customer or procured in accordance with the Customer's specifications or for designs specified by the Customer.

7. Customer’s right to subsequent performance as well as possible damage claims or claims for reimbursement of expenditures due to defects shall become time-barred after one year from delivery of the goods or after one year from acceptance of installations - or from completion of installations if such do not require acceptance. If the Supplier has fraudulently concealed the defect or has given a guarantee for the quality of the object, the statutory regulations shall apply to the limitation periods of any claims of the Customer in this regard. The statutory regu-lations shall also apply for the limitation periods of any damage claims of the Customer for defects if the Supplier is guilty of intention or gross negligence or if the damage claim is based on an injury to life, body or health.

Terms and Conditions of Sale and Delivery (Draft 04/2012)

91

8. Any and all further claims of the Customer shall be excluded, including but not limited to damage claims, and this includes damage that has not occurred at the object of delivery itself, if not provided otherwise under No. VIII.5., VIII.6 and VIII.7.

VIII. Withdrawal and Damage Claims on Part of Customer, Limitation of Action1. Customer may withdraw from the contract if it becomes finally impossible for the Supplier to perform the

contract before the transfer of risk. Any claim of the Customer for damages because of the final impossibility of performance shall be excluded, unless the Supplier is guilty of gross negligence in this regard. Any claim for damages shall be limited to the damage foreseeable at the time of conclusion of the contract and resulting from the ordinary course of events and shall be limited to a maximum amount of 15% of the contract total. Customer may also withdraw from the contract if, for an order of identical items, the delivery of part of the ordered items becomes impossible in terms of quantity and the Customer has a justified interest in refusing partial delivery. If this is not the case, the Customer may reduce the consideration accordingly.

2. If the impossibility occurs during a default in acceptance of the Customer or is the fault of the Customer, with no gross negligence on the part of the Supplier, the Customer's obligation for consideration is maintained and Customer is not entitled to withdraw from contract as provided under No. 1 above.

3. The Customer may withdraw from the contract if the Supplier is in default with its performance, if said perfor-mance is due, if the Customer has already granted a reasonable extension without success, and if the Supplier is responsible for its non-performance. Any damage claims of the Customer for arrears in delivery on the part of Supplier shall be excluded. Any damage claim is limited to the damage foreseeable at the time of conclusion of the contract and resulting from the ordinary course of events and is limited to an amount of 1/2 % for each full week of delay, in total to a maximum of 5% of the value of such part of the total delivery which cannot be used in due time because of the delay.

4. The Customer’s right to withdraw from the contract – beyond the cases regulated by above numbers 1 and 3 – in accordance with the statutory regulations, in the event of a violation of obligations for which the Supplier is responsible and which does not result from a defect, remains unaffected.

5. Any and all further claims of the Customer from violation of contractual obligations or tort in performing the con-tract shall be excluded, including but not limited to termination or damages, including claims for damages in lieu of performance and claims for compensation of expenses and compensation of damage of any type, inclu-ding such damage that has not occurred at the object of delivery itself. Excluded shall also be all further claims of Customer for other legal grounds, including Customer's claims from violation of pre-contract obligations or in tort for activities during negotiations or conclusion of the contract.

6. The disclaimers under these terms and conditions (including but not limited to items VIII.3 and VIII.5) do not apply • If the Supplier is responsible for gross negligence. • If the Supplier negligently violates material contract obligations (that means obligations of the Supplier that

are material for the subject matter and object of the contract and whose violation would compromise such object; and further, obligations whose fulfilment is a prerequisite for the proper performance of the contract, and therefore, the Customer regularly relies on and may rely on their fulfilment). If the Supplier negligently violates a material contract obligation, its liability to pay damages shall be limited to damage that is typical for the contract and foreseeable, to the extent there exists no wilful intent or gross negligence or if the Supplier is liable for damage to life, body or health.

• for any damage claim of Customer based on an intentional or grossly negligent damage to life, body or health.

• in such cases in which liability is statutory under the product liability act, for personal injury or damage to privately used property.

7. Damage claims of the Customer against the Supplier from violation of contractual obligations and from tort in connection with performance of the contract will become time-barred no later than one year from the end of the year in which the claim has arisen and the Customer has gained knowledge of the circumstances on which the claim is based and of the person of the debtor or had to have gained lacking gross negligence. This also applies to damage claims of the Customer against the Supplier for other legal grounds, including damage claims from violation of pre-contract obligations or in tort for activities during negotiations or conclusion of the contract. If the debtor is guilty of intent or gross negligence the statutory regulations apply. The statutory regu-lations further apply for any damage claims based on an intentional or grossly negligent damage to life, body or health.

8. To the extent that the Supplier's liability is excluded or limited, this applies too for any personal liability of its legal representatives and employees. For the limitation periods of claims of the Customer against the legal repre-sentatives of the Supplier and its employees, above number VIII.7 applies accordingly.

IX. Security1. The object of the delivery remains the property of the Supplier until full payment of the agreed price and of all

other receivables, including future claims from the business relationship with the Customer, has been received. This also applies, if individual receivables of the Supplier have been included in a current account; in such case the retention of title applies to the relevant balance. If in the context of the payment of the purchase price Supplier becomes liable on the basis of bills of exchange, the retention of title will not lapse before all bills of exchange have been honoured in full by the Customer.

2. The Customer hereby assigns to the Supplier all claims arising from the further sale of the objects of delivery, in the amount of the value of the objects of delivery, including all secondary rights. The Customer is authorized to collect the receivables. The Supplier's authority to collect the receivables itself remains unaffected.

3. The Supplier undertakes, in its own discretion, to release security at the request of the Customer, if the realiza-ble value of its security exceeds the total of its receivables from the business relationship by more than 10%.

4. As long as the Customer fulfils its obligations towards the Supplier, it is entitled to dispose of the object of delivery in the course of ordinary business and subject to the retention of title, if the claims are effectively trans-ferred to the Supplier in accordance with No. IX.2. Extraordinary disposals such as pledging, transfer by way of security and any and all assignments are not allowed. The Supplier must be notified in writing immediately of any attachment by third parties with respect to the object of delivery or assigned claims, including but not limited to pledges.

5. During the period of retention of title, the Customer is generally entitled to possess and make use as intended of the object of the delivery. In the event of actions in breach of contract by the Customer – including but not limited to arrears in payment by the Customer – and in the cases under No. IV.2., however, the Supplier may take possession of the object of delivery and revoke the authorization to collect the claims from further sale. The Customer – under exclusion of rights of retention – is obligated to surrender the object. The Customer shall bear any and all costs of repossession and exploitation. The Supplier is entitled to private sale. The Customer, at the request of the Supplier, shall immediately submit to the Supplier a list of all claims assigned in confor-mity with No. IX.2 as well as all additional information and documents necessary for exercising the claims to which the Supplier is entitled, and inform the debtors of the assignment.

6. The Customer shall maintain the object of delivery in a proper condition during the period of retention of title and allow the Supplier or a workshop authorized by the Supplier – except for emergencies – to perform imme-diately all maintenance and repair work prescribed by the Supplier.

7. In the case of trailers, the Supplier shall have the right to hold the certificate of title for the duration of the reten-tion of title.

8. If the retention of title or the assignment is not effective under the law of the country in which the goods are located, the security closest in nature to the retention of title or assignment in this country shall be deemed agreed. If the cooperation of the Customer is required for this purpose, the Customer shall perform all legal acts necessary to establish and preserve such rights.

X. Industrial Property RightsIf the Supplier is to perform according to drawings or models, samples, or using parts supplied by the Customer, the Customer shall warrant that industrial property rights of third parties are not infringed hereby. The Customer shall indemnify the Supplier from any and all third party claims for infringement of industrial property rights and shall compensate the Supplier for any resulting damage and for its costs and expenditure. If the Customer is prohibited from manufacture or delivery by a third party on grounds of industrial property rights, the Supplier is entitled to stop work. In this case, the Supplier may withdraw from the contract and demand compensation for its damage, costs and expenditure. An obligation on the part of the Customer for indemnification, damages and compensation of costs and expenses as provided under sentences 1 to 4 above does not exist, if the Customer is not responsible for the infringement of rights. However, any statutory rights and claims of the Supplier remain unaffected in any case.

XI. Use of SoftwareTo the extent that software is included in the scope of delivery, the Customer is granted a non-exclusive right to use the supplied software, including its documentation. It is licensed for use on the object of delivery intended for this purpose. The use of the software on more than one system is prohibited. The Customer may copy, rework or translate the software or convert the object code into the source code only to the extent permitted by the law (Sec. 69 a et. seq. UrhG, [German Copyright Act]). The Customer undertakes not to remove manufacturer infor-mation – including but not limited to copyright notices – or to change them without the prior express consent of the Supplier.All other rights to the software and the documentation, including copies, remain with the Supplier or the software supplier. The granting of sub-licenses is not permissible.

XII. Governing Law, Place of Performance, Jurisdiction, Severability1. The laws of the Federal Republic of Germany shall apply exclusively. In case of doubt, the German language ver-

sion of all contractual provisions shall be decisive. The Convention on the International Sale of Goods (CISG) do not apply.

2. Place of performance is 72631 Aichtal.

3. If the Customer is a merchant, a legal person under public law or a special fund under public law, the courts of Stuttgart shall have jurisdiction for any and all disputes arising under this contractual relationship, including disputes regarding its creation and its effectiveness as well as for bill of exchange and cheque litigation. The Supplier may apply to any other court which has jurisdiction according to statutory provisions.

4. If one of the provisions of these terms and conditions of sale and delivery is invalid, in whole or in part, the validity of the remaining provisions shall not be affected.

DYNAJET GmbHMax-Eyth-Straße 10, 72631 Aichtal, GermanyTelephone: +49. (0) 71 27. 5 99-618 | Fax: +49. (0) 71 27. 5 99-9671Website: www.dynajet.de | E-Mail: [email protected]

Errors excepted. Subject to technical changes without notice.

DYNAJET GmbH Max-Eyth-Strasse 10 72631 Aichtal Germany

Tel. + 49. (0) 71 27. 5 99 - 618 Fax + 49. (0) 71 27. 5 99 - 9671

Internet www.dynajet-online.comE-mail [email protected]

© DYNAJET GmbH, June 2012


Documents

General Catalogue - Høytrikksenteret Norge AS...General Catalogue Water Jetting Systems up to 3,000bar Edition No. 5 2 3 15 0 0 15 30 General overview of DYNAJET 4 28 – 31 36 –