General Specifications Differential Pressure TransmitterStatic Pressure Effects per pressure0.69 MPa (100 psi) Change Continuous Span Effects M and H capsules ±0.028% of span Effect

GeneralSpecifications

EJX210BFlange Mounted Differential Pressure Transmitter

Yokogawa Electric Corporation2-9-32, Nakacho, Musashino-shi, Tokyo, 180-8750 JapanTel.: 81-422-52-5690 Fax.: 81-422-52-2018

GS 01C27C01-01EN

GS 01C27C01-01EN©Copyright Feb. 200917th Edition Mar. 2019

The high performance flange mounted differential pressure transmitter EJX210B features single crystal silicon resonant sensor and is suitable to measure levels of densities of solidifying or precipitating liquids. EJX210B transmits not only process variables but also the setting parameters using wireless signal. In case of the battery powered type, the transmitter runs on internal batteries, and the installation cost can be decreased since hard-wiring is not required. The communication protocol is compliant with ISA100.11a protocol specifications.

FEATURES● LongLifeBatteryDesign

Ultra low current consumption design using two high capacity lithium-thionyl chloride batteries provide wireless operation for years.

● SecurityAssuredWirelessNetworkJoiningInfrared communication between the devices for wireless network configuration and parameter setting.

● QuickUpdateTimeSelectable from 0.5 second to 60 minutes for measured process value to publish wirelessly.

STANDARDSPECIFICATIONS■ WIRELESSSPECIFICATIONS

Communication protocol: ISA100.11a protocolData rate: 250 kbpsFrequency: 2400 - 2483.5 MHz license free ISM bandRadio security: AES 128 bit codifiedRF Transmitter power: Max. 11.6 dBmAntenna: +2 dBi Omni directional monopole typeSeparately sold remote antenna and antenna cables can be used.

■ POWERSUPPLYSPECIFICATIONSBattery:

Use the dedicated battery pack.Rated voltage: 7.2 VRated capacity: 19 Ah

External Power Source:Rated voltage: 10.5 to 30 V DCRated current: 36 mA

■ SPANANDRANGELIMITSMeasurement Span/Range

M

H

1 to 100

–500 to 500

Span

SpanRange

Range

kPa

4 to 400–400 to 400

–2000 to 200020 to 2000

–100 to 1005 to 500

10 to 1000

–5000 to 5000

–1000 to 100050 to 5000

inH2O(/D1) mbar(/D3) mmH2O(/D4)

100 to 10000–10000 to 100000.05 to 5 kgf/cm2

–5 to 5 kgf/cm2

T01E.ai

■ PERFORMANCESPECIFICATIONSZero-based calibrated span, linear output, wetted parts material code SW for 3-inch flange flush type, fill fluid code B, and in the continuous measurement mode.

SpecificationConformanceEJX series ensures specification conformance to at least ±3σ.

ReferenceAccuracyofCalibratedSpan(includes terminal-based linearity, hysteresis, and repeatability)Measurement span

Referenceaccuracy

±0.075% of Span

±(0.025+0.01 URL/span)% of Span

T02-1E.ai

XX > span

X ≤ span

URL (upper range limit)

H

100 kPa (400 inH2O)500 kPa (2000 inH2O)

Measurement span

Referenceaccuracy

±0.075% of Span

±(0.025+0.005 URL/span)% of Span

M

T02-2E.ai

X

X > span

X ≤ span

URL (upper range limit)10 kPa (40 inH2O)

100 kPa (400 inH2O)

../submenu.htm../../index.htm

2

All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation

GS 01C27C01-01EN

AmbientTemperatureEffectsper28°C(50°F)Change

Capsule EffectHM

±[0.14% Span +0.028% URL]±[0.224% Span +0.056% URL]

StaticPressureEffectsper0.69MPa(100psi)Change

SpanEffectsM and H capsules±0.028% of span

EffectonZeroM and H capsules±0.007% of URL

Stability±0.1 % of URL per 12 months

BatteryCharacteristicBattery pack with long life lithium-thionyl chloride batteries. With the intrinsically safe type, the battery pack is replaceable in hazardous area.Typical battery life is 10 years at 30 seconds update time or 5 years at 10 seconds update time in the following conditions.*

• Ambient temperature: 23±2°C• Device role: IO mode• LCD display: off* Environmental condition such as vibration may affect

the battery life.ResponseTime(Differentialpressure)

M and H capsule: 180 ms (approximate value at normal temperature)Including dead time of 100 ms (nominal)

StaticPressureSignalRangeandAccuracy (Includesterminal-basedlinearity,hysteresis,andrepeatability)

RangeUpper Range Value and Lower Range Value of the statice pressure can be set in the range between 0 and Maximum Working Pressure (MWP*). The upper range value must be greater than the lower range value. Minimum setting span is 0.5 MPa (73 psi).

*: Maximum Working Pressure (MWP) is within flange rating pressure.

AccuracyAbsolute Pressure1 MPa or higher: ±0.2% of spanLess than 1 MPa: ±0.2%×(1 MPa/span) of spanGauge Pressure ReferenceGauge pressure reference is 1013 hPa (1 atm)

Note : Gauge pressure variable is based on the above fixed reference and thus subject to be affected by the change of atomospheric pressure.

■ FUNCTIONALSPECIFICATIONSOutput

Wireless (ISA100.11a protocol) 2.4 GHz signal.Output mode, linear or square root, is selectable.

UpdateTimeMeasurement

modeDifferentialpressure Pressure

Continuous 100 ms 100 ms

Intermittent 0.5 to 3600 s selectable0.5 to 3600 s

selectable The transmitter shifts to the countinuous mode

when the update time is set to 0.5 second. ZeroAdjustmentLimits

Zero can be fully elevated or suppressed, within the lower and upper range limits of the capsule.

ExternalZeroAdjustmentExternal zero is continuously adjustable with 0.01% incremental resolution of span.

IntegralIndicator(LCDdisplay)5-digit numerical display, 6-digit unit display and bar graph.The indicator is configurable to display one or up to three of the following variables periodically.;Differential pressure, static pressure, temperature. See also “Factory Setting.”

SelfDiagnosticsCapsule failure, amplifier failure, configuration error, battery alarm, wireless communication alarm and over-range error for process variables.

SoftwareDownloadFunctionSoftware download function permits to update wireless field device software via ISA100.11a wireless communication.

BatteryPack2x primary lithium-thionyl chloride batterieswith battery case (batteries sold separately)

■ NORMALOPERATINGCONDITION (Optionalfeaturesorapprovalcodesmayaffectlimits.)

AmbientTemperatureLimits-40 to 85°C (-40 to 185°F)-30 to 80°C (-22 to 176°F) LCD visible range

(Note: The ambient temperature limits must be within the fill fluid operating temperature range, see table 1.)

ProcessTemperatureLimitsHigh pressure side: See table 1.Low pressure side: 40 to 120°C (-40 to 248°F)

AmbientHumidityLimits0 to 100% RH

WorkingPressureLimitsSee table 1.For atmospheric pressure or below, see figure 1.

Mar. 28, 2019-00


3

All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 01C27C01-01EN

Table1.Processtemperature,Ambienttemperature,andWorkingpressure

T03E.ai

Process temperature *1*2

–10 to 85°C(14 to 185°F)

2.7 kPa abs (0.38 psi abs) to

flange rating pressure

Ambient temperature *3 Working pressure

A –10 to 250°C *4

(14 to 482°F)

Code

Silicone oil

*1: See figure 1 ‘Working Pressure and Process Temperature.’*2: Indicates high pressure side value. The process temperature limit for low pressure side is –40 to 120°C (–40 to 248°F).*3: This ambient temperature is the transmitter ambient temperature.*4: In case of wetted parts material code TW (Tantalum), process temperature limit is up to 200°C (392°F).

2.7 (0.38)

100 (14.5)

1 (0.14)

10 (1.4)

–50(–58)

0(32)

50(122)

100(212)

150(302)

200(392)

250(482)

300(572)

F01E.ai

Process temperature rangeFlange max.working pressure

Atmosphericpressure

Transmitter ambienttemperature range

Process Temperature °C (°F)

Working pressurekPa abs(psi abs)

Figure1.WorkingPressureandProcessTemperature

■ REGULATORYCOMPLIANCESTATEMENTSThis device contains the wireless module which satisfies the following standards.

* Please confirm that an installation region fulfills an applicable standard. If additional regulatory information and approvals are required, contact a Yokogawa representative.

EMCConformityStandardsEN61326-1 Class A, Table 2 (For use in industrial locations), EN61326-2-3

RadioEquipmentDirective(RE)ETSI EN 300 328, ETSI EN 301 489-1, ETSI EN 301 489-17, EN61010-1, EN61010-2-030, EN62311• Indoor/Outdoor use

Dec. 25, 2018-00

EuropeanPressureEquipmentDirective 2014/68/EUSound Engineering Practice

EURoHSDirective EN50581SafetyRequirementStandards EN61010-1, EN61010-2-030

• Installation category: I(Anticipated transient overvoltage 330 V)

• Pollution degree: 2• Indoor/Outdoor use

RegulationConformityoftheWirelessModule• FCC Approval• ISED Approval

■ PHYSICALSPECIFICATIONSProcessconnections Highpressureside:

Flange connectedSee the following table.

Table2.Flangesizeandrating

Size

4-inch3-inch

Flange

3-inch2-inch1 1/2-inch*

JIS 10K, 20KANSI Class 150, 300JPI Class 150, 300DIN PN10/16, 25/40

Process connection style

Flush type

JIS 10K, 20KANSI Class 150, 300JPI Class 150, 300DIN PN10/16, 25/40

Extended type

T04E.ai

*: Flushing connection rings are always attached. Lowpressureside:

Threaded See “MODEL AND SUFFIX CODES.”Process connection of cover flange: IEC61518

GasketContactSurfaceSee the following table.

Table3.Gasketcontactsurface

T05E.ai

SW,SE,WW,WE●

HW,TW

ANSISW,SE,WW,WE—

JIS/JPI/DINHW,TW

Serration*1 —●

—● ●●Flat (No serration)

Wetted parts material code

Flange

Gasket contact Surface

: Applicable, —: Not applicable*1: ANSI B16.5


4


GS 01C27C01-01EN

WettedPartsMaterial Highpressureside:

Refer to “MODEL AND SUFFIX CODES” Flushingconnectionring(optional) RingandVent/Drainplugs

Refer to “MODEL AND SUFFIX CODES” (Spiral)gasketfortransmitterside

316 SST (Hoop), PTFE Teflon (Filler) Lowpressureside: Diaphragm,CoverFlange,ProcessConnector,CapsuleGasket,andVent/DrainplugRefer to “MODEL AND SUFFIX CODES”

ProcessconnectorgasketPTFE Teflon

Non-wettedPartsMaterial ProcessFlange

Refer to “MODEL AND SUFFIX CODES” Bolting

B7 carbon steel, 316L SST, or 660 SST Housing

Low copper cast aluminum alloy Coatingofhousing

[for aluminum housing]Polyester resin powder coatingMint-green paint (Munsell 5.6BG 3.3/2.9 or its equivalent)[for option code /P or /X2]Epoxy and polyurethane resin solvent coating

DegreesofProtectionIP66/IP67, NEMA4X

CoverO-ringsBuna-N

Nameplateandtag316 SST tag plate wired onto transmitter.

FillFluidSilicone oil, Fluorinated oil (optional)

Weight Flushtype

3-inch ANSI Class150 flang: 11.1 kg (24.2 lbs)* Extendedtype

4-inch ANSI Class150 flange, extension length (X2)=100 mm: 15.6 kg (34.4 lbs)*

* The weight does not include that of battery pack, mounting bracket and process connector.

Add 0.3 kg for the external powered type.

<RelatedInstruments>Field Wireless System: Refer to GS 01W01A01-01ENField Wireless Management Station YFGW410: GS 01W02D01-01ENField Wireless Access Point YFGW510: GS 01W02E01-01ENField Wireless Access Point YFGW520: GS 01W02E02-01ENField Wireless Media Converter YFGW610: GS 01W02D02-01EN

Mar. 28, 2019-00


5


MODELANDSUFFIXCODES InstructionThe model and suffix codes for EJX210B consist of two parts; a transmitter body section (I) and a flange mounting section (II). This specification sheet introduces these two parts separately. The transmitter body section is shown in one table, and the flange mounting section specifications are listed according to the flange size and the process connection style. First select the model and suffix codes of transmitter body section and then continue on one of the flange mounting section.

F02E.ai

EJX210B

I Transmitter body section

• Flush type (3, 2, or 1 1/2-inch)• Extended type (4 or 3-inch)

II Flange mounting section

I.Transmitterbodysection

T06E.ai

Installation8· · · · · · · · ·9· · · · · · · · ·

Cast aluminum alloy with detachable antenna (2 dBi)*2Cast aluminum alloy without antenna (N connector)*1*2

Amplifier housing

DescriptionSuffix codes

The ‘►’ marks indicate the most typical selection for each specification.*1: Order the antenna separately from accessory option. *2: Remote antenna cables can be attached. Order separately from accessory option.*3: Material of a blind plug; aluminum alloy for code 5 and 9, and 304 SST for code 7.

S · · · · · · · · · · · · · · ·

0 · · · · · · · · · · · · ·1 · · · · · · · · · · · · ·2 · · · · · · · · · · · · · 3 · · · · · · · · · · · · · 4 · · · · · · · · · · · · ·5 · · · · · · · · · · · · ·

J · · · · · · · · · · · G · · · · · · · · · · · C · · · · · · · · · · ·

J · · · · · · ·0 · · · · · · ·2 · · · · · · ·4 · · · · · · · 5 · · · · · · ·7 · · · · · · ·9 · · · · · · · A · · · · · · ·C · · · · · · · D · · · · · · ·

-9 · · · · · · · · ·

D · · · · ·

Flange mounted differential pressure transmitter· · · · · · · · · · · · · · · · · · · ·

M · · · · · · · · · · · · · · · ·H · · · · · · · · · · · · · · · · ·

-L · · · · · · · · · · · · · · · · · ·-1 · · · · · · · · · · · · · · · · · ·

B7 carbon steel 316L SST 660 SST

without process connector (Rc 1/4 female on the cover flange) with Rc 1/4 female process connector with Rc 1/2 female process connector with 1/4 NPT female process connector with 1/2 NPT female process connector without process connector (1/4 NPT female on the cover flange)

Refer to "Low Pressure Side Wetted Parts Materials" Table below.

Horizontal piping type and left side high pressure

Wireless communication (ISA100.11a protocol)Wireless communication (ISA100.11a protocol); successor of code –L1 to 100 kPa (4 to 400 inH2O) 5 to 500 kPa (20 to 2000 inH2O)

No electrical connection, battery powered type (battery case only; battery cells not included)G1/2 female, one electrical connection without blind plugs, external powered type 1/2 NPT female, two electrical connections without blind plugs, external powered type M20 female, two electrical connections without blind plugs, external powered typeG1/2 female, two electrical connections and a blind plug, external powered type*31/2 NPT female, two electrical connections and a blind plug, external powered type*3M20 female, two electrical connections and a blind plug, external powered type*3G1/2 female, two electrical connections and a 316 SST blind plug, external powered type 1/2 NPT female, two electrical connections and a 316 SST blind plug, external powered typeM20 female, two electrical connections and a 316 SST blind plug, external powered type

Continued on flange mounting section (II)

Digital indicatorN · · · Always N

Low pressure sidewetted parts materialLow pressure sideProcess connections

►Coverflange bolts and nuts material

Electrical connection

Integral Indicator

ModelEJX210B

Measurement span (Capsule)

Output signal

Flange mounting section—

Table. Low Pressure Side Wetted Parts Materials

*1: Cast version of 316 SST. Equivalent to SCS14A.*2: Hastelloy C-276 or ASTM N10276 The ‘#’ marks indicate the construction materials conform to NACE material recommendations per MR01-75 (2003). For the use of 316 SST material, there may be certain limitations for pressure and temperature. Please refer to NACE standards for details.

CapsuleCover flange and

process connector Capsule gasketLow pressure side wetted

parts material code Vent/Drain plug

Teflon-coated 316L SST 316 SSTHastelloy C-276*2 (Diaphragm)F316L SST, 316L SST (Others)S

# ASTM CF-8M*1

EJX210B

Mar. 28, 2019-00


6


GS 01C27C01-01EN Feb. 1, 2017-00

II.Flangemountingsection(Flushtype) Precessflangesize:3-inch(80mm)

T07E.ai

DescriptionSuffix codesModelEJX210B

Gasket contact surface *1

Flange rating

Flange material►

Flushing connection ring *2►

Wetted parts material (high pressure side) *8

Flange size

Transmitter body section (I) · · · · · · · · · · · · · · · · · · ·Process connection style

ExtensionFill fluid

1 · · · · · · · · · · ·2 · · · · · · · · · · ·

J1 · · · · · · · · · · · · · · ·J2 · · · · · · · · · · · · · · ·A1 · · · · · · · · · · · · · · ·A2 · · · · · · · · · · · · · · ·P1 · · · · · · · · · · · · · · ·P2 · · · · · · · · · · · · · · ·D2 · · · · · · · · · · · · · · ·D4 · · · · · · · · · · · · · · ·

A · · · · · · · · · · · ·B · · · · · · · · · · · ·C · · · · · · · · · · · ·

0 · · · · · · ·A · · · · · · ·B · · · · · · ·

SW · · · · · · ·HW · · · · · · ·TW · · · · · · ·

3 · · · · · · · · · · · · · ·

-W · · · · · · · · · · · · · · · · ·

0 · · · · · ·

-A · · ·

[Diaphragm] [Others] 316L SST # 316 SST # Hastelloy C-276*6 # Hastelloy C-276*6 # Tantalum*7 Tantalum*7

Serration (for ANSI flange with wetted parts material SW only) Flat (no serration)

3-inch (80 mm)

JIS 10K JIS 20K ANSI class 150 ANSI class 300 JPI class 150 JPI class 300 DIN PN10/16 DIN PN25/40

Flush type

JIS S25C 304 SST*9 316 SST*9

Option codes / Optional specification

[Ring] [Vent/Drain plugs] [Material]None — —Straight type R 1/4 connections*5 316 SST #Straight type 1/4 NPT connections 316 SST #

[Process temperature] *3 [Ambient temperature]Silicone oil –10 to 250°C*4 –10 to 85°C

None

The ‘►’ marks indicate the most typical selection for each specification. Example: EJX210B-LMS5G-98JDN-WA13B1SW00-A/ *1: See Table 3 ‘Gasket contact surface.’ *2: When specified flushing connection ring code A or B, exclusive gasket is provided for transmitter side. *3: Indicates the process temperature limit of high pressure side. The process temperature limit for low pressure side is –40 to 120°C. *4: In case of wetted parts material code TW (Tantalum), the process temperature limit is –10 to 200°C. *5: Not applicable for gasket contact surface code 1. *6: Hastelloy C-276 or ASTM N10276 *7: Not applicable for flushing connection ring code A and B.*8: Users must consider the characteristics of selected wetted parts material and the influence of process fluids. The use of inappropriate materials can result in the leakage of corrosive process fluids and cause injury to personnel and/or damage to plant facilities. It is also possible that the diaphragm itself can be damaged and that material from the broken diaphragm and the fill fluid can contaminate the user’s process fluids. Be very careful with highly corrosive process fluids such as hydrochloric acid, sulfuric acid, hydrogen sulfide, sodium hypochlorite, and high-temperature steam (150°C [302°F] or above). Contact Yokogawa for detailed information of the wetted parts material.*9: Forged version of the material may be used.The ‘#’ marks indicate the construction materials conform to NACE material recommendations per MR01-75 (2003).Please refer to NACE standards for details.

EJX210B W 3


7

All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 01C27C01-01EN Feb. 1, 2017-00

II.Flangemountingsection(Flushtype) Precessflangesize:2-inch(50mm)

T08E.ai


The ‘►’ marks indicate the most typical selection for each specification. Example: EJX210B-LMS5G-98JDN-WA12B1WW00-A/ *1: See Table 3 ‘Gasket contact surface.’ *2: When specified flushing connection ring code A or B, exclusive gasket is provided for transmitter side. *3: Indicates the process temperature limit of high pressure side. The process temperature limit for low pressure side is –40 to 120°C. *4: In case of wetted parts material code TW (Tantalum), the process temperature limit is –10 to 200°C. *5: Not applicable for gasket contact surface code 1. *6: Hastelloy C-276 or ASTM N10276*7: Not Applicable for flushing connection ring code A and B.*8: Users must consider the characteristics of selected wetted parts material and the influence of process fluids. The use of

inappropriate materials can result in the leakage of corrosive process fluids and cause injury to personnel and/or damage to plant facilities. It is also possible that the diaphragm itself can be damaged and that material from the broken diaphragm and the fill fluid can contaminate the user’s process fluids.

Be very careful with highly corrosive process fluids such as hydrochloric acid, sulfuric acid, hydrogen sulfide, sodium hypochlorite, and high-temperature steam (150°C [302°F] or above). Contact Yokogawa for detailed information of the wetted parts material.

*9: Forged version of the material may be used.The ‘#’ marks indicate the construction materials conform to NACE material recommendations per MR01-75 (2003). Please refer to NACE standards for details.

ModelEJX210B


Flange rating

Flange material►



Flange size

Transmitter body section (I) · · · · · · · · · · · · · · · · · ·Process connection style

ExtensionFill fluid

1 · · · · · · · · · ·2 · · · · · · · · · ·

J1 · · · · · · · · · · · · · · ·J2 · · · · · · · · · · · · · · ·A1 · · · · · · · · · · · · · · ·A2 · · · · · · · · · · · · · · ·P1 · · · · · · · · · · · · · · ·P2 · · · · · · · · · · · · · · ·D2 · · · · · · · · · · · · · · ·D4 · · · · · · · · · · · · · · ·

A · · · · · · · · · · · ·B · · · · · · · · · · · ·C · · · · · · · · · · · ·

0 · · · · · · ·A · · · · · · ·B · · · · · · ·

WW · · · · · · ·HW · · · · · · ·TW · · · · · · ·

2 · · · · · · · · · · · · · ·

-W · · · · · · · · · · · · · · · ·

0 · · · · ·

-A · · ·

[Diaphragm] [Others] Hastelloy C-276*6 # 316 SST # Hastelloy C-276*6 # Hastelloy C-276*6 # Tantalum*7 Tantalum*7

Serration (for ANSI flange with wetted parts material WW only) Flat (no serration)

2-inch (50 mm)


Flush type

JIS S25C 304 SST*9 316 SST*9


[Ring] [Vent/Drain plugs] [Material]None — —Straight type R 1/4 connections*5 316 SST #Straight type 1/4 NPT connections 316 SST #

[Process temperature] *3 [Ambient temperature]Silicone oil –10 to 250°C*4 –10 to 85°C

None

EJX210B W 2


8


GS 01C27C01-01EN

II.Flangemountingsection(flushtype) Precessflangesize:11/2-inch(40mm)

T09E.ai


The ‘►’ marks indicate the most typical selection for each specification. Example: EJX210B-LMS5G-98JDN-WA18B1WWC0-A/ *1: See Table 3 ‘Gasket contact surface.’ *2: When specified flushing connection ring code C or D, exclusive gasket is provided for transmitter side. *3: Indicates the process temperature limit of high pressure side. The process temperature limit for low pressure side is –40 to 120°C. *4: Not applicable for gasket contact surface code 1. *5: Hastelloy C-276 or ASTM N10276*6: Users must consider the characteristics of selected wetted parts material and the influence of process fluids. The use of

inappropriate materials can result in the leakage of corrosive process fluids and cause injury to personnel and/or damage to plant facilities. It is also possible that the diaphragm itself can be damaged and that material from the broken diaphragm and the fill fluid can contaminate the user’s process fluids.

Be very careful with highly corrosive process fluids such as hydrochloric acid, sulfuric acid, hydrogen sulfide, sodium hypochlorite, and high-temperature steam (150°C [302°F] or above). Contact Yokogawa for detailed information of the wetted parts material.

*7: Forged version of the material may be used.The ‘#’ marks indicate the construction materials conform to NACE material recommendations per MR01-75 (2003). Please refer to NACE standards for details.

ModelEJX210B


Flange rating

Flange material►



Flange size

Transmitter body section (I) · · · · · · · · · · · · · · · · · ·Process connection style

ExtensionFill fluid

1 · · · · · · · · · ·2 · · · · · · · · · ·

J1 · · · · · · · · · · · · · · ·J2 · · · · · · · · · · · · · · ·A1 · · · · · · · · · · · · · · ·A2 · · · · · · · · · · · · · · ·P1 · · · · · · · · · · · · · · ·P2 · · · · · · · · · · · · · · ·

A · · · · · · · · · · · ·B · · · · · · · · · · · ·C · · · · · · · · · · · ·

C · · · · · · ·D · · · · · · ·

WW · · · · · · ·

8 · · · · · · · · · · · · · ·

-W · · · · · · · · · · · · · · · ·

0 · · · · · ·

-A · · ·

[Diaphragm] [Others] Hastelloy C-276*5 # 316 SST #

Serration (for ANSI flange only) Flat (no serration)

1 1/2-inch (40 mm)

JIS 10K JIS 20K ANSI class 150 ANSI class 300 JPI class 150 JPI class 300

Flush type

JIS S25C 304 SST*7 316 SST*7


[Ring] [Vent/Drain plugs] [Material]Reducer type R 1/4 connections*4 316 SST #Reducer type 1/4 NPT connections 316 SST #

[Process temperature] *3 [Ambient temperature]Silicone oil –10 to 250°C –10 to 85°C

None

EJX210B W 8

Feb. 1, 2017-00


9

All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 01C27C01-01EN Feb. 1, 2017-00

II.Flangemountingsection(Extendedtype) Precessflangesize:4-inch(100mm)

T10E.ai

The ‘►’ marks indicate the most typical selection for each specification. Example: EJX210B-LMS5G-98JDN-EA14B1SE01-A/ *1: See Table 3 ‘Gasket contact surface.’*2: Indicates the process temperature limit of high pressure side. The process temperature limit for low pressure side is –40 to 120°C. *3: Users must consider the characteristics of selected wetted parts material and the influence of process fluids. The use of inappropriate materials can result in the leakage of corrosive process fluids and cause injury to personnel and/or damage to plant facilities. It is also possible that the diaphragm itself can be damaged and that material from the broken diaphragm and the fill fluid can contaminate the user’s process fluids. Be very careful with highly corrosive process fluids such as hydrochloric acid, sulfuric acid, hydrogen sulfide, sodium hypochlorite, and high-temperature steam (150°C [302°F] or above). Contact Yokogawa for detailed information of the wetted parts material.*4: Forged version of the material may be used.The ‘#’ marks indicate the construction materials conform to NACE material recommendations per MR01-75 (2003). Please refer to NACE standards for details.



Flange rating

Flange material►

Flushing connection ring


Flange size


Extension

Fill fluid

1 · · · · · · · · · ·2 · · · · · · · · · ·

J1 · · · · · · · · · · · · · · ·J2 · · · · · · · · · · · · · · ·A1 · · · · · · · · · · · · · · ·A2 · · · · · · · · · · · · · · ·P1 · · · · · · · · · · · · · · ·P2 · · · · · · · · · · · · · · ·D2 · · · · · · · · · · · · · · ·D4 · · · · · · · · · · · · · · ·

A · · · · · · · · · · · ·B · · · · · · · · · · · ·C · · · · · · · · · · · ·

0 · · · · · · ·SE · · · · · · ·

4 · · · · · · · · · · · · · ·

-E · · · · · · · · · · · · · · · · ·

1 · · · · ·3 · · · · ·5 · · · · ·

-A · · ·

[Diaphragm] [Others] [Pipe]316L SST # 316 SST # 316 SST #


4-inch (100 mm)

JIS 10K JIS 20K ANSI class 150 ANSI class 300 JPI class 150 JPI class 300DIN PN10/16 DIN PN25/40

Extended type

JIS S25C 304 SST*4 316 SST*4


None


Length (X2) = 50 mm Length (X2) = 100 mm Length (X2) = 150 mm

EJX210B E 4


10


GS 01C27C01-01EN

II.Flangemountingsection(Extendedtype) Precessflangesize:3-inch(80mm)

T11E.ai



Flange rating

Flange material►

Flushing connection ring


Flange size


Extension

Fill fluid

1 · · · · · · · · · · ·2 · · · · · · · · · · ·

J1 · · · · · · · · · · · · · · ·J2 · · · · · · · · · · · · · · ·A1 · · · · · · · · · · · · · · ·A2 · · · · · · · · · · · · · · ·P1 · · · · · · · · · · · · · · ·P2 · · · · · · · · · · · · · · ·D2 · · · · · · · · · · · · · · ·D4 · · · · · · · · · · · · · · ·

A · · · · · · · · · · · ·B · · · · · · · · · · · ·C · · · · · · · · · · · ·

0 · · · · · · ·WE · · · · · · ·

3 · · · · · · · · · · · · · ·

-E · · · · · · · · · · · · · · · · ·

1 · · · · · ·3 · · · · · ·5 · · · · · ·

-A · · ·

[Diaphragm] [Others] [Pipe]Hastelloy C-276*3 # 316 SST # 316 SST #


3-inch (80 mm)


Extended type

JIS S25C 304 SST*5 316 SST*5


None


Length (X2) = 50 mm Length (X2) = 100 mm Length (X2) = 150 mm

The ‘►’ marks indicate the most typical selection for each specification. Example: EJX210B-LMS5G-98JDN-EA13B1WE01-A/ *1: See Table 3 ‘Gasket contact surface.’ *2: Indicates the process temperature limit of high pressure side. The process temperature limit for low pressure side is –40 to 120°C. *3: Hastelloy C-276 or N10276*4: Users must consider the characteristics of selected wetted parts material and the influence of process fluids. The use of inappropriate materials can result in the leakage of corrosive process fluids and cause injury to personnel and/or damage to plant facilities. It is also possible that the diaphragm itself can be damaged and that material from the broken diaphragm and the fill fluid can contaminate the user’s process fluids. Be very careful with highly corrosive process fluids such as hydrochloric acid, sulfuric acid, hydrogen sulfide, sodium hypochlorite, and high-temperature steam (150°C [302°F] or above). Contact Yokogawa for detailed information of the wetted parts material.*5: Forged version of the material may be used.The ‘#’ marks indicate the construction materials conform to NACE material recommendations per MR01-75 (2003). Please refer to NACE standards for details.

EJX210B E 3

Feb. 1, 2017-00


11


OPTIONALSPECIFICATIONS(ForExplosionProtectedtype)Item Description Code

FactoryMutual(FM)

FM Intrinsically safe Approval Applicable Standard: Class 3600:2011, Class 3610:2015, Class 3611:2016, Class 3810:2005, ANSI/UL-60079-0-2013, ANSI/UL-60079-11-2014, NEMA-250:2003 Intrinsically Safe for Class I, Division 1, Groups A, B, C & D, Class II, Division 1, Groups E, F & G and Class III, Division 1, Class I, Zone 0, in Hazardous Locations, AEx ia IIC Nonincendive for Class I, Division 2, Groups A, B, C & D, Class II, Division 2, Groups F & G and Class III, Division 1, Class I, Zone 2, Group IIC, in Hazardous Locations Enclosure: Type 4X, Temp. Class: T4, Amb. Temp.: –50 to 70°C (–58 to 158°F)

FS17*1

ATEX

ATEX Intrinsically safe Approval Applicable Standard: EN 60079-0: 2012+A11:2013, EN 60079-11: 2012, EN60079-28: 2015 Certificate: KEMA 10ATEX0164 X II 1 G Ex ia op is IIC T4 Ga Degree of protection: IP66/IP67 Maximum Process Temp.(Tp): 120°C (248°F) Amb. Temp.(Tamb): –50 to 70°C (–58 to 158°F)

KS27*1

CanadianStandardsAssociation

(CSA)

CSA Intrinsically safe Approval No. CSA10CA2325443X Applicable standard: CAN/CSA-C22.2 No.94, C22.2 No.213, CAN/CSA-C22.2 No.61010-1, CAN/CSA-C22.2 No.60079-0, CAN/CSA-C22.2 No.60079-11, CAN/CSA-C22.2 No.60529 Ex ia IIC T4 Ga Intrinsically Safe for Class I, Division 1, Groups A, B, C & D, Class II, Division 1, Groups E, F & G, Class III, Division 1. Nonincendive for Class I, Division 2, Groups A, B, C & D, Class II, Division 2, Groups F & G, Class III, Division 1 Enclosure: IP66/IP67 and Type 4X Temperature Code: T4 Maximum Process Temp.(Tp): 120°C (248°F) Amb. Temp.(Tamb): –0 to 70°C (–8 to 158°F)

CS17*1

IECEx

IECEx Intrinsically safe Approval Applicable Standard: IEC60079-0:2011, IEC60079-11:2011, IEC 60079-28:2015 Certificate: IECEx KEM 10.0074 X Ex ia op is IIC T4 Ga *2 Enclosure: IP66/IP67 Maximum Process Temp.(Tp): 120°C (248°F) Amb. Temp.(Tamb): –50 to 70°C (–58 to 158°F)

SS27*1

*1: Only applicable for selecting Electrical connection code J.*2: For Output signal -L, the Type of Protection and Marking code is Ex ia IIC T4 Ga.

Dec. 25, 2018-00


12


GS 01C27C01-01EN

OPTIONALSPECIFICATIONSItem Description Code

PaintingColor change Amplifier cover only PCoating change Anti-corrosion coating *1 X2

Oil-prohibited use Degrease cleansing treatment K1Oil-prohibited usewith dehydrating treatment Degrease cleansing and dehydrating treatment K5

Calibration units*2P calibration (psi unit)

(See Table for Span and Range Limits.)D1

bar calibration (bar unit) D3M calibration (kgf/cm2 unit) D4

Teflon film*3 *4 Diaphragm protection from sticky process fluid by FEP Teflon film attached with fluorinated oil. Operation range: 20 to 150°C, 0 to 2 MPa (Not applicable for vacuum service). TF1

Gold-plated diaphragm*5 Inside of isolating diaphragms (fill fluid side) are gold plated, effective for hydrogen permeation. A1

Material certificate

For Flush type

High Pressure side: Process flange, Block *6 Low Pressure side: Cover flange M0W

High Pressure side: Process flange, Block *7 Low Pressure side: Cover flange, Process connector M1W

High Pressure side: Process flange, Block, Ring *6 *8 Low Pressure side: Cover flange M3W

High Pressure side: Process flange, Block, Ring *7 *8 Low Pressure side: Cover flange, Process connector M4W

For Extended type

High Pressure side: Process flange, Block, Pipe, Base *6 Low Pressure side: Cover flange M0E

High Pressure side: Process flange, Block, Pipe, Base *7 Low Pressure side: Cover flange, Process connector M1E

Pressure test/Leak test certificate*9 *10

(Flange rating) (Test pressure)JIS 10K 2 MPa (290 psi)

Nitrogen(N2) Gas*13Retention time: one minute

T51JIS 20K 5 MPa (720 psi) T54ANSI/JPI Class 150 3 MPa (430 psi) T52ANSI/JPI Class 300 8 MPa (1160 psi)*11 T56ANSI/JPI Class 300 7 MPa (1000 psi)*12 T55

*1: Not applicable with color change option.*2: The unit of MWP (Max. working pressure) on the name plate of a housing is the same unit as specified by option code D1,

D3, and D4.*3: Applicable for flush type (process connection style code W.)*4: Applicable for flushing connection ring code 0.*5: Applicable for wetted parts material code SW, SE, WW, WE, and HW.Consult Yokogawa in case gold-plated diaphragm is

required for low pressure side.*6: Applicable for Low Pressure Side Process connection code 0 and 5.*7: Applicable for Low Pressure Side Process connection code 1, 2, 3, and 4.*8: Applicable for flushing connection ring code A, B, C, and D.*9: The unit on the certificate is always MPa regardless of selection of option code D1, D3, or D4. *10: A flushing connection ring will not be applied when conducting the pressure test or leak test. *11: Applicable for flush type (process connection style code W.) *12: Applicable for extended type (process connection style code E.) *13: Pure nitrogen gas is used for oil-prohibited use (option code K1 and K5.)

OPTIONALACCESSORIESProduct Partnumber Specification

Battery pack assembly F9915NQ*1 Battery case, Lithium-thionyl chloride batteries 2 piecesBatteries*2 F9915NR Lithium-thionyl chloride batteries, 2 piecesBattery case F9915NK*3 Battery case onlyRemote antenna cable F9915KU 3 m with mounting bracket

F9915KV 13 m (3 m+10 m), with a surge protective device and mounting bracketAntenna F9915KW 2 dBi standard antenna

F9915KY 6 dBi high gain antenna*4 *5

*1: If you need F9915MA, please purchase F9915NQ. F9915NQ is a set of F9915MA and instruction manual.*2: Alternatively, Tadiran SL-2780/S, TL-5930/S or VITZROCELL SB-D02 batteries can be purchased from your local

distributor.*3: If you need F9915NS, please purchase F9915NK. F9915NK is a set of F9915NS and instruction manual.*4: Use of high gain antenna is limited by local regulation of radio and telecommunication law. Consult Yokogawa for details.*5: F9915KY can not connect directly to the transmitter. Remote antenna cable is required to use F9915KY.

Mar. 28, 2019-00


13

All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 01C27C01-01EN Mar. 28, 2019-00

DIMENSIONS

Flush type No ring

(Flushing connection ring code 0)

Unit: mm (approx. inch)

With ring (Flushing connection ring code A, B, C, and D)

Extended type

*1: Indicates inside diameter of gasket contact surface.*2: When option code K1 or K5 is selected, add 15 mm (0.59 inch) to the value in the flange. Add 11 mm (0.36 inch) for drain/vent plugs of flushing connection ring.*3: When amplifier housing code 9 is selected, the value is 270 mm (10.63 inch). In this case, the figure is shown as A.*4: Applicable for the external powered type.*5: When electrical connection code 7 or C is selected, a blind plug is protruded upto 8 mm from the electrical connection. F03E.ai

A*3

*5: Flushing connection ring

Flange size 3 or 2 inch Flange size 1 1/2 inch

Straight type Reducer type

76(2.99)

6(0.24)

For electricalconnection code5, 9, A and D

76(2.99)

6(0.24)


76(2.99)

6(0.24)


62(2.44)

390*

3 (1

5.35

)

62(2.44)

390*

3 (1

5.35

)

62(2.44)

390*

3 (1

5.35

)

143 (5.63)

91 (3

.58)181

(7.1

3)

211

(8.3

1)

64(2.52)

191 (7.52)

39(1.54)

140(5.51)

25(0.98)

Ø11

0 (4

.33)

54(2.13)

38*2(1.50)

24(0.94)

41(1.61)

67(2.64)

Process flange

X2

Process connection

Process connector(Optional)

Zero adjustment

Vent plugDrain plug

Low pressure sideprocess connection

t

f

ØD

ØC

Øg

ØA

n-Øh

Terminal side

Groundterminal

143 (5.63)

91 (3

.58)

211

(8.3

1)

181

(7.1

3)

112

(4.4

1)

191 (7.52)

64(2.52)

140(5.51)

39(1.54)

Ø11

0 (4

.33)

54(2.13)

24(0.94)

41(1.61)

67(2.64)

Process flange

Process connection


Vent plugDrain plug


38*2(1.50)

n-Øh

Ground terminal

Vent/Drain plug j

ft

k

ØD

ØC

Øg

n-Øh

Zero adjustment

Flushing connection ring*5

Terminal side

143 (5.63)

91 (3

.58)181

(7.1

3)

211

(8.3

1)

64(2.52)

191 (7.52)

39(1.54)

140(5.51)

25(0.98)

Ø11

0 (4

.33)

54(2.13)

38*2(1.50)

24(0.94)

41(1.61)

67(2.64)

Process flange

Process connection


Zero adjustment

Vent plugDrain plug


t

fØ

DØ

CØ

gØ

d*1

n-Øh

Terminal side

Integral indicator

Electrical connection*4

Integral indicatorElectrical connection*4

Integral indicatorElectrical connection*4

dø

Spiralgasket

Spiralgasket

44ø

Ground terminal


14


GS 01C27C01-01EN

Process flange size: 4 inch (100 mm)



Process flange size: 1 1/2 inch (40 mm)

Unit: mm (Approx.: inch)

T12E.ai

*1: Indicates inside diameter of gasket contact surface.

øg

155 (6.10)155 (6.10)155 (6.10)155 (6.10)155 (6.10)155 (6.10)155 (6.10)155 (6.10)

øC

175 (6.89)185 (7.28)

190.5 (7.50)200.2 (7.88)190.5 (7.50)200.2 (7.88)180 (7.09)190 (7.48)

t

18 (0.71)24 (0.94)

23.9 (0.94)31.8 (1.25)24 (0.94)32 (1.26)20 (0.79)24 (0.94)

øD

210 (8.27)225 (8.86)

228.6 (9.00)254 (10.00)229 (9.02)254 (10.0)220 (8.66)235 (9.25)

Code

J1J2A1A2P1P2D2D4

Flange rating

JIS 10KJIS 20KANSI class 150ANSI class 300JPI class 150JPI class 300DIN PN10/16DIN PN25/40

ød

————————

k

————————

øA

96±0.5 (3.78±0.02)96±0.5 (3.78±0.02)96±0.5 (3.78±0.02)96±0.5 (3.78±0.02)96±0.5 (3.78±0.02)96±0.5 (3.78±0.02)96±0.5 (3.78±0.02)96±0.5 (3.78±0.02)

j

————————

No.(n)88888888

Dia.(øh)19 (0.75)23 (0.91)

19.1 (0.75)22.4 (0.88)19 (0.75)22 (0.87)18 (0.71)22 (0.87)

øg

130 (5.12)130 (5.12)130 (5.12)130 (5.12)130 (5.12)130 (5.12)130 (5.12)130 (5.12)

øC

150 (5.91)160 (6.30)

152.4 (6.00)168.1 (6.62)152.4 (6.00)168.1 (6.62)160 (6.30)160 (6.30)

t

18 (0.71)22 (0.87)

23.9 (0.94)28.5 (1.12)24 (0.94)

28.5 (1.12)20 (0.79)24 (0.94)

øD

185 (7.28)200 (7.87)

190.5 (7.50)209.6 (8.25)190 (7.48)210 (8.27)200 (7.87)200 (7.87)

Code

J1J2A1A2P1P2D2D4

Flange rating


ød*1

90 (3.54)90 (3.54)90 (3.54)90 (3.54)90 (3.54)90 (3.54)90 (3.54)90 (3.54)

k

27 (1.06)27 (1.06)27 (1.06)27 (1.06)27 (1.06)27 (1.06)27 (1.06)27 (1.06)

øA

71±0.5 (2.8±0.02)71±0.5 (2.8±0.02)71±0.5 (2.8±0.02)71±0.5 (2.8±0.02)71±0.5 (2.8±0.02)71±0.5 (2.8±0.02)71±0.5 (2.8±0.02)71±0.5 (2.8±0.02)

j

25 (0.98)25 (0.98)25 (0.98)25 (0.98)25 (0.98)25 (0.98)25 (0.98)25 (0.98)

No.(n)88484888

Dia.(øh)19 (0.75)23 (0.91)

19.1 (0.75)22.4 (0.88)19 (0.75)22 (0.87)18 (0.71)18 (0.71)

øg

100 (3.94)100 (3.94)100 (3.94)100 (3.94)100 (3.94)100 (3.94)100 (3.94)100 (3.94)

øC

120 (4.72)120 (4.72)

120.7 (4.75)127.0 (5.00)120.6 (4.75)127.0 (5.00)125 (4.92)125 (4.92)

t

16 (0.63)18 (0.71)

19.1 (0.75)22.4 (0.88)19.5 (0.77)22.5 (0.89)18 (0.71)20 (0.79)

øD

155 (6.10)155 (6.10)

152.4 (6.00)165.1 (6.50)152 (5.98)165 (6.50)165 (6.50)165 (6.50)

Code

J1J2A1A2P1P2D2D4

Flange rating


ød*1

61 (2.40)61 (2.40)61 (2.40)61 (2.40)61 (2.40)61 (2.40)61 (2.40)61 (2.40)

k

27 (1.06)27 (1.06)27 (1.06)27 (1.06)27 (1.06)27 (1.06)27 (1.06)27 (1.06)

j

25 (0.98)25 (0.98)25 (0.98)25 (0.98)25 (0.98)25 (0.98)25 (0.98)25 (0.98)

No.(n)48484844

Dia.(øh)19 (0.75)19 (0.75)

19.1 (0.75)19.1 (0.75)19 (0.75)19 (0.75)18 (0.71)18 (0.71)

øg

86 (3.39)86 (3.39)86 (3.39)86 (3.39)86 (3.39)86 (3.39)

øC

105 (4.13)105 (4.13)98.4 (3.87)114.3 (4.50)98.6 (3.88)114.3 (4.50)

t

16 (0.63)18 (0.71)

17.5 (0.69)20.6 (0.81)17.6 (0.69)20.6 (0.81)

øD

140 (5.51)140 (5.51)127 (5.00)

155.4 (6.12)127 (5.00)155 (6.10)

Code

J1J2A1A2P1P2

Flange rating

JIS 10KJIS 20KANSI class 150ANSI class 300JPI class 150JPI class 300

ød*1

44 (1.73)44 (1.73)44 (1.73)44 (1.73)44 (1.73)44 (1.73)

k

30 (1.18)30 (1.18)30 (1.18)30 (1.18)30 (1.18)30 (1.18)

j

27 (1.06)27 (1.06)27 (1.06)27 (1.06)27 (1.06)27 (1.06)

No.(n)444444

Dia.(øh)19 (0.75)19 (0.75)

15.9 (0.63)22.4 (0.88)16 (0.63)22 (0.87)

Extension code50 (1.97)

X21

5100 (3.94)3150 (5.91)

Extension length (X2)

Bolt holes

Bolt holes

Bolt holes

Bolt holes

Sep. 22, 2010-00


15

All Rights Reserved. Copyright © 2009, Yokogawa Electric Corporation GS 01C27C01-01EN Dec. 25, 2018-00

2-inch pipe (O.D. 60.5 mm)

72 (2.83)17(0.67)

F04E.ai

Unit: mm (approx. inch)

Antenna mounting bracket

Antenna/Cable

Non-directional antenna• Gain: 2 dBi

Part number: F9915KW

Antenna cable• Sheath diameter: 11.2 mm• Gain: 6 dBi

Part number: F9915KY

Part number: F9915KU

Part number: F9915KV

130

(5.1

2)

Ø14(Ø0.55)

Ø21(Ø0.83)

500

(19.

69)

Ø26(Ø1.02)

Ø22(Ø0.87)

68(2.68)

2 dBi antenna

*1: When 6 dBi antenna is selected, the value is 642 mm (25.28 inch).

Transmitter body Transmitter body

19(0

.75)

25(0

.98)

18(0.69)

88 (3

.46)

135

(5.3

1)272

(10.

71)*1

98 (3.86)

Cable 1Length: 3 m

Cable 2Length: 10 m

Cable 1Length: 3 m

Surge protective device

Antenna

Antenna


16


GS 01C27C01-01ENSubject to change without notice.

Infrared port

Infrared Configuration Terminal Configuration for the External Powered type

Terminal Wiring Example for the External Power Source Terminal

Ground terminalPower supply terminal +

Power supply terminal –

Power supply

Connectionterminal

Shield cable

External power source

Use shield cables if it is affected by electrical noise.

10.5-30V DC

F05E.ai

<FactorySetting>Tag No. Blank unless otherwise specified in orderSoftware tag Blank unless otherwise specified in orderNetwork ID ‘1‘ unless otherwise specified in order.

Static pressure display range

‘0 to 25 MPa’ for M and H capsule, absolute value.Measuring low pressure side.

<Reference>1. is a registered trademark of Yokogawa

Electric Corporation.2. Teflon; Trademark of E.I. DuPont de Nemours & Co.3. Hastelloy; Trademark of Haynes International Inc.Other company names and product names used in this material are registered trademarks or trademarks of their respective owners.

<InformationonEUWEEEDirective>EU WEEE (Waste Electrical and Electronic Equipment) Directive is only valid in the EU.This instrument is intended to be sold and used only as a part of equipment which is excluded from WEEE Directive, such as large-scale stationary industrial tools, a large-scale fixed installation and so on, and, therefore, subjected to the exclusion from the scope of the WEEE Directive. The instrument should be disposed of in accordance with local and national legislation/regulations.

Mar. 28, 2019-00

<OrderingInformation>Specify the following when ordering1. Model, suffix codes, and option codes2. Calibration range and unit

1) RangeCalibration range can be specified with range value specifications up to 5 digits for low or high range limits within the range of -32000 to 32000.When reverse range is designated, specify Lower Range Value (LRV) as greater than Upper Range Value (URV).

2) UnitSpecify only one unit from Table A.

TableA.AvailableRangeUnitEJX210B mmH2O, mmH2O (68°F), mmHg, Pa, kPa,

MPa, mbar, bar, gf/cm2, kgf/cm2, inH2O, inH2O (68°F), inHg, ftH2O, ftH2O (68°F) or psi

3. Output modeSelect Liner.

4. Display setting (SCALE)1) Display scale and unit

Specify either “0 to 100 %” or “Desired Range and Unit” for engineering unit scale:- When “Desired Range and Unit” is specified,

scale range can be specified with range limit specifications up to 5 digits for low or high range limits within the range of -32000 to 32000. Unit display consists of 6-digit, therefore, if the specified scaling unit excluding “/” is longer than 6-characters, the first 6 characters will be displayed on the unit display.

2) Display modeSelect Liner.

5. Tag Number (if required)Specify Tag number (up to 16 letters, valid characters: alphanumeric, hyphen and underscore) to be engraved on the tag plate. The specified letters are written on TAG_Name (16 letters) in the amplifier memory.

6. Software tag (if required)Specify this software tag when tag number which is different from the tag number specified in the “Tag Number” is required. The tag number specified in “Software tag” will be entered on “TAG_NAME” (up to 16 letters) in the amplifier memory.

7. Network ID (if required)Specify the number from 2 to 65535.When not specified, it will use 1 as the default.

Documents

General Specifications Differential Pressure TransmitterStatic Pressure Effects per pressure0.69 MPa (100 psi) Change Continuous Span Effects M and H capsules ±0.028% of span Effect