Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
TREATMENT ROOMACCESSIBILITY
DEN
TAL
CH
AIR
ROTA
TES
FOR
ASSI
ST IN
TO C
HAI
R
32" POINT CLEARANCEMAINTAINED
16" O
.C. (
TYP
.)
8"8"
WOOD STUD WALL.2 x 4
SET PLATE 1/4" CLEAR
SPACE.1/4" CLEAR
BETWEEN WALLS.STUDS EQUALLY
ACOUSTIC. BATT INSUL.
WOOD STUD WALL.2 x 4
R-11 'FACED'
SOUND BOARD1/2" FIBER
OF ADJOINING SOUND BD.OFFSET 16" SPACING OF
GYP. BOARD (TYP.)5/8" TYPE-X
2'-0
"2'
-0"
STUDS @ 24" O.C.2 1/2" 25 GAUGE STEEL
MIN. 1" THERMAFIBER SAFB
FIRECODE C CORE GYP.5/8" SHEETROCK BRAND
1/2" RESILIENT CHANNEL
(2) LAYERS EACH SIDE,
SPACED 24" O.C. MAX
*BASED ON USG ACOUSTICAL ASSEMBLY RAL-TL-83-214, PROVIDING A MIN. STC 61
COORDINATION OF DRAWINGS
GENERAL TENANT IMPROVEMENT NOTES
This icon designates points of important coordination with dental equipment supply company representative. Notesdescribing specific coordinating effort follow.
DENTAL EQUIPMENT SUPPLIER COORDINATION
Design efforts and construction documents have been reviewed and aligned to the greatest degree possible. It remains the responsibility of theGeneral Contractor, however, to accomplish final coordination of the work, and to recognize the significance of the parties providing for the design ofthe project. It is extremely important for the General Contractor to obtain all contact information and documentation (completed by: 1. ProjectArchitect; 2. Unthank Design Group; 3. Dental Equipment Supplier) prior to completion of bid and/or pricing efforts. Any conflicts in the contractdocuments, or arising from the direction of the Dental Equip. Supplier, shall be brought to the attention of The Architect immediately for clarification.For a complete list of the primary project contacts, refer to bottom portion of drawing "CS", (Cover Sheet).
18. The general contractor shall coordinate with the dental equipment supplier for installation of special equipment not shown in these drawings. The general contractor shall verify equipment locations with the dental equip. supplier and/or equip. manufacturer for proper size and location of blocking, backing and utility connections.
1. General project notes apply to all "D" sheets.
2. These drawings and copies thereof are legal instruments of service for use of the owner only.
3. Any deviations from the contract documents which are necessitated by field conditions shall be brought to the attention of the architect.
4. All dimensions are actual and are to face of finish, face of concrete walls, face of frames, or centerline of columns, unless noted otherwise. Exceptions include clear hold dimensions and finished face dimensions on floor plan and reflected ceiling plan.
5. Wall types are designated on the floor plan sheet D1.
6. All walls shall extend to underside of structure above unless noted otherwise.
7. Provisions shall be made at all full-ht nonbearing wall for 1" vertical movement of the building structure without transfer of compressive loads to wall.Fill irregularities between top of wall and deck above with fire safing insulation or fire stopping materials as req'd to meet fire rating of respective walls.
8. All penetrations through walls shall be sealed with fire stopping material as req'd to achieve the respective fire-resistive rating and smoke stoppage.
9. The general contractor shall furnish and install wood blocking in metal stud partitions for the proper anchorage of all wall attached items: i.e. toiletaccessories, cabinets, wall-mounted fixtures, etc. General contractor must verify & provide rated wood studs in walls as required by code.
10. Gypsum board surfaces shall be isolated with control joints as per manufacturers requirements and industry standards.
11. The contractor shall include all owner furnished and installed items and owner furnished and contractor installed items in the construction, and shall coordinate with the owner to accommodate these items.
12. Scribe gypsum board of wall and partitions to irregularities of deck above. Seal tightly around any partitions.
13. All work shall conform to the requirements within the current editions of all local, city, state and federal applicable codes adopted by the local jurisdiction. This includes but is not limited to fire, smoke, Americans with Disabilities Act, egress, medical gases & Life Safety.
14. Each trade shall be held responsible for knowledge of general notes included throughout the contract documents and the applicable bldg. codes.
15. All colors and finish materials shall be approved by the Owner and Owner's agent. Provide 6" x 6" sample for all stained wood to Unthank Design Group for approval.
16. Noted dimensions take precedence over scaled dimensions, do not scale drawings.
17. The HVAC, plumbing and electrical drawings are supplementary to the arch. drawings. Should there be any discrepancy between the variousdrawings, it shall be brought to the architect's attention for clarification. Refer to the elevation drawings (on the D10-12 sheets) for locations of undercabinetry lighting, compressed air, vacuum or gas outlets. Any compressed air, vacuum, or water to be provided in the trtmt. rooms will be notedon the floor plan, or as detailed on sheet D7. (Note: HVAC contractor shall provide adequate ventilation/cooling for server/tech closet, see also D5).
25. All light fixtures that come into contact with building insulation must be IC Rated. All light fixtures shall meet all applicable codes from National Electric Code (NEC) to the International Energy Code (IEC). Contractor is to verify code compliance of all light fixtures.
19. All hardwood trim to be as detailed on sheet D6.
20. In the event discrepancies or conflicts arise among drawings and/or other descriptions contained herein, the contractor shall notify the architect immediately for clarification.
21. Contractor shall visit project site prior to submittal of bid. Contractor shall establish scope of work from construction documents and actual project site visit. Any omissions, discrepancies or clarifications are to be brought to the immediate attentions of the architect. Failure of contractor to perform in this manner does not allow for additional cost to the owner.
22. All gypsum board surfaces are to be finished smooth. Gypsum Association GA-214-96 level 4 finish, with the following addition; any readily visible imperfections in gypsum board surface shall be coated with joint compound and/or skim-coated as required.
23. General Contractor must verify and coordinate all operational requirements and clearance dimensions of project components; including Contractor supplied and Owner supplied items. This includes but is not limited to the functional aspects of the following: A) Appliances, dishwasher, refrigerator, washer, dryer, microwave, disposal, etc. (i.e., door operation clears all door trim, cased opening trim and wall mounted items.) B) Electronic devices, copier, fax machine, computer, television, VCR, DVD player, sound components, etc. (i.e., raise bottom of wall cabinets 6" where counter top copier lid conflicts occur.) C) Cabinetry, hardware, pulls, slides, etc. Coordinate and ensure complete free and clear operation of drawers and doors. Provide a 1 1/2" scribe at the ends of all cabinet runs abutting adjacent wall assemblies to ensure adequate clearances.
24. Contractor shall itemize all costs and scope of work regarding any change order. This information must be presented to the Owner and Architect for approval prior to any work being executed.
PROJECT TEAM - DEFINITIONSOWNER: All references to 'Owner' in these architectural drawings refer to the individual / group of individuals named in the titleblock.
UNTHANK DESIGN GROUP: Dental design consultants. 'Interior Architecture' & 'Interior Design' portions of the project. See 'D' sheets & room finishschedule.
PROJECT ARCHITECT: Also 'Building Shell Architect', 'Coordinating Professional', 'Local Architect' & 'Architect of Record'. Local architect responsiblefor preparing complete drawings for building department review & permit.
ENGINEER: Prepares Civil, Landscape, Structural, and MEP drawings under the direction of the Project Architect.
DENTAL EQUIPMENT SUPPLIER (D.E.S.) : Prepares dental equipment specifications & drawings illustrating dental utility requirements. Responsiblefor installation of dental equipment (excludes piped utilities).
OTHERS: All references to 'Others' in these architectural drawings refer to specific trade professionals in relation to the item noted.
26. HVAC Zoning: Should the HVAC system be design-build, Contractor must provide minimum of two (2) separate control zones, each with their ownthermostat (see also page D2 for suggested thermostat locations). Reception Desk areas & Waiting Room areas are NEVER to share a control zone with "Treatment Rooms", "Operatories", "Treatment Bays", "Open Bays", and/or "Quiet Rooms". Contractor to verify number and extent of HVAC control zones prior to bidding. Contractor must verify final location of all thermostats with Owner prior to wiring/installation. The Owner may make reasonable changes to final thermostat location(s), prior to wiring, from what is shown on plans at no additional expense to Owner.
27. All finish materials are to be installed according to product manufacturer’s most current directions and recommendations (including but not limited to;adhesives, surface preparation, subfloor/substrate conditions, moisture barriers, concrete moisture content, concrete pH, etc.). G.C. andSubcontractors are responsible for verifying all current directions and reqt's with product manufacturers before ordering and installing finish materials.
TI COVER SHEET& SCHEDULES
D1
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
1) Do not locate plumb. supply and waste lines below trash drops in countertops.This area must be kept clear for waste receptacles by Owner. See cabinet elevs.
6) Provide recirculating pump and related piping return loop for Hot water piping.
2) Verify requirements for water heater and any plumbing connections to dentalequipment and HVAC system with owner and Dental Equipment Supplier. (Also seecomp. air and/or nat. gas plan notes this sheet.) Do not place plumbing supply orvent lines where recessed towel & tissue dispensers are to be located. See alsosheets D10, D11, D12, D13, and FLOOR PLAN, this sheet.
3) Provide cold water supply line to refrigerator in staff lounge and to counterlocation in lab. See lab keynote #17 this sheet.
4) Provide water main electrically controlled solenoid valve remote on-off switchlocated on sheet D5 and this sheet.
5) Verify locations of all recessed dispensers indicated in these drawings. Plumbingsupply and vent piping shall not interfere with rough-in areas for dispensers.Plumbing lines improperly placed will be corrected at no additional cost to owner.
7) See Room Finish Schedule for plumbing fixture color & finish specifications.
PLUMBING NOTES:
Note: Dimensions nominal, see sections, sheet D8 for cabinetbox and countertop details/dimensions.
Drawing sheet number.Detail or elevation number.
U = Upper CabinetL = Lower CabinetC = CountertopS = Shelving
MILLWORK
Stud Wall
Sound Wall
SYMBOLS LEGEND
Cabinet depth
see section dets.
U=
13"
L=24
"
101
Door number
3 5/8" Metal studs with 5/8" Type X gypsum wall board onboth sides, and 3 1/2" acoustic batt insulation betweenthe studs, unless noted otherwise. All sound wallassemblies full-height to decking, including gypsum wallboard. Scribe & connect wall to underside of deckingmaterial above (typ.). Acoustically seal all penetrations.
3 5/8" Metal studs, 20 GA, 16" O.C. with 5/8" Type Xgypsum board on both sides, unless noted otherwise.Terminate gypsum wall board 4" +/- above finishedceiling condition, typ.
Note: 2x4 wood studs may be substituted for 3 5/8" metal studs.(General Contractor must verify & provide rated woodstuds in walls & blocking as required by code).
in inches -
Building shell, demising wall, etc. construction. Allelements, design, detailing and drawings by others.
This icon designates points of important coordinationwith dental equipment supply company representative.Notes describing specific coordinating effort follow.
8) D.W. indicates under-counter dishwasher location. Provide supply & drain asrequired, verify with equipment reqt's.
SOUND WALL 11
9) W/D indicates washer and dryer location. Provide supply & drain as required,verify with equipment reqt's.
L.V.P.RUN Flooring plank direction.
PLUMBING FIXTURE SCHEDULE
P-4 SINKKohler 'Mayfield' #K-5964-3, 25"x22"x8" single compartment,enameled cast iron with Kohler #8801 strainer. Provide one (1)Delta #141-DST single lever faucet and one (1) Delta #441-DSTsingle lever faucet with sprayer with two (2) sets of supplies andstops. Install sprayer in center hole of sink, with single leverfaucets at sides. (See finish sched. for fixture color selection.)
P-8 MOP RECEPTORFlorestone #MSR-2424 mop receptor. Provide Fiat #830-AAservice sink faucet. (Wall mount faucet; verify mounting heightw/ owner.)(See room finish schedule for fixture color selection.)
P-2 WATER CLOSETKohler 'Highline Pressure Lite' #K-3493 17 1/8"H, with #K-4652'Lustra' seat and supply w/ stop. (Add 1 inch to rough indimension from rear wall as allowance for tile wainscotthickness). Trip lever to be to wide 'approach' side of room-where wide side to Right; change to #K-3493-RA (right trip lever).Verify w/ Floor Plan. (See finish sched. for fixture color selection.)
P-3 LAVATORYKohler 'Radiant' #K-2917-4 self-rimming, 19" diameterenameled cast iron with Delta #520 MPU DST faucet.(Seeroom finish schedule for fixture color selection.)
FD FLOOR DRAIN Provide floor drain at location shown.
P-9 EXTRACTOR'Extractor' unit. (Precision Equipment Services, Inc. (605)347-0452 Contact: Lance Moon). Locate Extractor in lowerportion of statim cabinet. Drain to plumbing waste.'Extractor' provided and installed by General Contractor.
P-7 SINKKohler 'Addison' #K-6552, self-rimming 13"x13"x6" enameled castiron sink with Kohler #8801 strainer. Sink shall be provided with aDelta #141-DST faucet and 'Tapmaster' #1770 "Euro"foot-activation unit. Do not place supply or vent lines whererecessed towel & tissue dispensers are to be located. See alsointerior elevations and FLOOR PLAN, this sheet. (Layout per detail9/D9.) (See room finish schedule for fixture color selection.)
P-6 SINKKohler 'Iron/Tones' #K-6584, 17"x19"x8" enameled cast iron,provided with a deck mounted Delta #340-DST faucet w/ sprayer,Kohler #K-8801 strainer, and 1-1/2" tailpiece to sediment trapbelow counter. Sediment trap provided by Dent. Equip. Supp.
P-5 SINKKohler 'Iron/Tones' #K-6584, 17"x19"x8" enameled cast iron,provided with a deck mounted Delta #340-DST faucet. Provideand install 'In-Sink-Erator' Badger 5XP 3/4 HP garbage disp.(See room finish schedule for fixture color selection.)
P-1 LAVATORYKohler 'Caxton' #K-2210 undermount, 17"x14" with deckmounted Kohler 'Revival' #K-16102-4A-BN faucet. (Seeroom finish schedule for fixture color selection.)
A Surface fluorescent 1-32w
B Recessed fluorescent 4-32w(5000K 90 CRI)
Lithonia #Z 1 32 MVOLT GEB10IS LP850
Lithonia #2GT8 4 32 A12125 MVOLT GEB10ISLP850 (with prismatic diffuser) (EXEMPT fromenergy calculations, see note #11)
LIGHT FIXTURE SCHEDULE
C Recessed fluorescent 3-32w Lithonia #2GT8 3 32 A12125 MVOLT GEB10IS(with prismatic diffuser)
Mark Description Lamp Manufacturer/Product
D Wallwash fluorescent 1-18w TRTComp. Fluor.
Lithonia, Gotham #AFW 1/18TRT 6AR MVOLTGEB10
E Recessed fluorescent 3-32w Lithonia #2GT8 3 32 PC2S MVOLT GEB10IS (withparabolic louver)
EM Emergency light Lithonia 'Quantum' #ELM2 emergency lighting unit(white). Mount on wall, 6" below ceiling.
EX1 Exit light Lithonia 'Precise' #LRP 1 GC 120/277 EL N, ceilingmount, green on clear.
EX2 Exit light Lithonia 'Precise' #LRP 2 GMR DA 120/277 EL N,ceiling mount, green on mirror.
F Recessed fluorescent 2-32w Lithonia #GT8 2 32 PC2S MVOLT GEB10IS (withparabolic louver)
G Recessed fluorescent 1-18w DTT Lithonia #LP6F 18DTT 607AZ MVOLT GEB10IS
H Recessed fluorescent 1-26w TRT Lithonia #LF6N 1/26TRT F601AZ MVOLT GEB10IS
H1 Rec. fluor. (dimming) 1-26w TRT Lithonia #LF6N 1/26TRT F601AZ 120 ADEZ IS
J Designates Electrical Junction Box
K Recessed incandescent 1-35w PAR20 Lithonia #L3 301AZ
L Under-counter LED puck light LED puck light system, undercounter. One 'puck'centered under each paper-shelf at control counter(see #9/D8). Verify number of lights with plan &interior elevations. Puck light color to be black.
S Surface fluorescent 2-32w Lithonia #SB 2 32 MVOLT GEB10IS
T1 Wall accent Fluor. Hubbardton Forge #206741-05. Mount at 72"A.F.F. Verify w/ Owner.
T2 Valance Light Fluor. Vanity fixture O.S.C.I. (In TLT. RM. mount at 6'-8"A.F.F. Verify with Owner)
P Under-cabinet LED LED Phillips Color Kinetics eW Profile Powercore 523-000027-73.Verify & provide all required system components andaccessories.
R Under-cabinet LED LED Phillips Color Kinetics eW Profile Powercore 523-000027-74.Verify & provide all required system components andaccessories.
T3 MonoRail System 12v halogen 'Tech Lighting' MonoRail System (1) #700MOA 48 Z. ProvideEnd Caps (2) #700MOCCAP Z, one at each end of run. Mount(1) 'Tech Lighting' River Rock pendant light #700MORIVRSZ(sand / antique bronze). Bottom of pendants to be mounted at6'-0" A.F.F. (Position as shown). Provide w/ 2" Rigid Standoffs#700MOS02 Z as req'd. Provide remote transformer & powerfeed canopy as req'd.
M Surface fluorescent 2-17w Lithonia #SB 2 17 MVOLT GEB10IS
T4 MonoRail System 12v halogen 'Tech Lighting' MonoRail System (1) #700MOA 96 Z, field cut to7'-0" length. Provide End Caps (2) #700MOCCAP Z, one ateach end of run. Mount two (2) 'Tech Lighting' River Rockpendant lights #700MORIVRSZ (sand / antique bronze).Bottomof pendants to be mounted at 6'-0" A.F.F. (Position as shown).Provide w/ 2" Rigid Standoffs #700MOS02 S as req'd. Provideremote transformer & power feed canopy as req'd.
T5 MonoRail System 12v halogen 'Tech Lighting' MonoRail System (1) #700MOA 96 Z, field cut to5'-0" length. Provide End Caps (2) #700MOCCAP Z, one ateach end of run. Mount two (2) 'Tech Lighting' River Rockpendant lights #700MORIVRSZ (sand / antique bronze).Bottomof pendants to be mounted at 6'-0" A.F.F. (Position as shown).Provide w/ 2" Rigid Standoffs #700MOS02 S as req'd. Provideremote transformer & power feed canopy as req'd.
EXHAUST FAN SCHEDULE
Y Exhaust Fan Nutone #QTXEN110
Mark Description Manufacturer/Product
1) Exhaust fans are to be vented to outside.
EXHAUST FAN NOTES:
2) See drawings by Engineer for full MEP plans. General Contractor shallcompare drawings & bring any discrepancies to the attention of theArchitect for clarification.
Z Exhaust Fan Nutone #8210. Equip fan w/ Nutone inlineautomatic adjustable thermostat. Verify temp.setting w/ dent. equip. supplier & HVAC contractor.
X Exhaust Fan Nutone #ZN110M
1/4" = 1'
ADA2 0"SOUND WALL 23
1D2
L=18" L=18" L=18" L=18" L=18" L=18" L=18" L=18" L=18" L=18" S=12" S=12"
S=
12"
L=18
"L=
18"
L=18
"L=
18"
L=18
"L=
18"
L=18
"L=
18"
L=18
"L=
18"
L=18"U=13"
L=18"U=13"L=
24"
L=12
"U
=12
"
C=
24"
U=
15"
C=24"U=15"
L=12"U=12"
C=24"U=13"
L=24"U=13"
C=
24"
U=
13"
C=
24"
U=
13"
S=12"
S=
12"
S=
12"
C=
30"
C=24"U=15"
C=24"U=13"
C=24"U=13"
C=
24"
U=
18"
C=
24"
U=
15"
U=
18"
S=18"
L=24"S=12"
L=24
"U
=13
"
L=24
"U
=13
"
L=24"
L=24
"
L=24
"
L=24
"
L=18"
L=24"S=18"
L=30
"U
=18
"L=12"S=12"
C=12"
C=
30"
C=24"U=15"
S=12"S=
12"
L=24"U=15"
L=24"U=13"
L=24
"U
=13
"
L=24
"U
=13
"L=
24"
U=
13"
C=
30"
C=
12"
C=30"
C=12"
C=
20"
L=24
"U
=18
"
10'-7 7/8" 10'-6" 10'-6" 10'-6" 10'-6" 5'-4 7/8" 4'-4 7/8" 5'-2 7/8" 12'-5 1/2"
85'-2" ( VERIFY W/ BUILDING SHELL DRAWINGS)
7'-10 1/4" 4'-8 1/8"
5'-6 7/8" 16'-8 5/8" 15'-6 5/8"9'-0 3/4"9'-8 7/8"
VEST.101
ELEV.103
UTIL.104
STAIR102
GREET.105
WAITING106
KIDS107
CTRL.108
BUS.109
R.R.110
OFC.111
HALL112
LAB113
CL.114
FIN.115
HALL116
CEREC117
DIST.118
REAPPT.119
HALL120
HALL121
CNSLT.122
SVR.123
PAN124 STERIL.
125
HALL126
HALL127
STAIR128
C./V.129
VEST.130
ELEC131
CL.132
SUPP.133
HALL134
HALL135
R.R.136
C.A.137
PAT. ED.138
R.R.139
R.R.140
JAN.141
R.R.142
TRTMT.143
TRTMT.144
TRTMT.145
TRTMT.146
TRTMT.147
TRTMT.148
TRTMT.149
TRTMT.150
TRTMT.151
TRTMT.152
7'-0
"4'
-8"
10'-4
7/8
"10
'-6"
10'-6
"10
'-6"
10'-1
1/4
"
63'-8
" ( V
ER
IFY
W/ B
UIL
DIN
G S
HE
LL D
RA
WIN
GS
)
15'-1
0 1/
4"8'
-3 1
/4"
18'-1
1 7/
8"6'
-6"
7'-6
5/8
"
6'-6
"
1D1
60" DIA. C
LR.
60" DIA. C
LR.
60" DIA. C
LR.
2'-10 1/2"11'-7 1/8" 8'-4 3/4" 5'-6 1/2" 4'-1 5/8" 3'-7 5/8" 7'-11 3/4" 4'-7 7/8" 1'-4 1/8" 10'-6 5/8"
9'-6 3/8" 6'-4 7/8"
10'-1
1/4
"4'
-10
1/8"
15'-1
0 1/
4"4'
-11
1/4"1
1/8"
2'-0
7/8
"8'
-10
7/8"
5'-2
1/4
"4'
-8"
7'-0
"
10'-6
5/8
"1'
-4 1
/8"
4'-1
1 1/
2"11
'-0 7
/8"
4'-7
5/8
"2'
-2 3
/4"
3'-9
5/8
"5'
-3 3
/8"
5'-3
1/8
"
ALIGN ALIGN ALIGN
ALI
GN
ALIGN
ALIGN ALIGN ALIGN
ALIGN (TYP.)
ALI
GN
(TY
P.)
8'-6 7/8" 2'-0 7/8" 1'-4" 5'-4 7/8" 3'-4 7/8" 8'-3 3/8" 1'-0" 5'-4 7/8" 8'-10 7/8" 7'-4 7/8" 7'-8 7/8" 9'-0 7/8" 4'-7 7/8"
6'-4 7/8" 1'-0"4'-1 1/8"5'-3 7/8"
8"
3'-7 5/8" 7'-11 3/4" 1'-0"
3'-4 7/8"6'-1 1/2"6'-1 1/2"6'-3 3/4" 1'-9 3/4"CL
CL
C L
CL
5'-0"
4'-0
1/4
"
C L
1'-7
"
*
1'-4
"
*
2'-2
"
*R2'
-6"
1"
*
1"
*1'-0"
*
9D8
C L
3'-1
0 7/
8"
15'-7
1/4
"
2'-1
1 5/
8"
C L
4'-6
1/4
"4'
-0 1
/8"
3'-5
5/8
"3'
-7 1
/8"
1'-0
"
*
1'-0
"
*
2'-6
"
*
1'-0
"
*
ALIGN 1'-0
"
*45°
1'-0
"
*
45°
45°
45°
45°
45°
45°
45° 45°
45°
45°
45°
4-7/
8"
*
4-7/
8"
*
1'-0"
*
1'-3
1/8
"R
2'-6
"
1'-8"CLR
*
4'-8
"
1'-5
5/8
"6'
-5 3
/8"
7'-1
1 1/
4"3
3/8"
1'-7
1/8
"
6'-0
"C
LEA
R*
3'-0"CLEAR
*
1'-10"
*
1'-2"
*
1'-2
"*
1'-2
"
*
1'-2
"
*
5'-4"CLEAR
*
4'-6
"C
LEA
R*1'
-9"
CLR
*
4'-6"CLEAR
*
3'-6"CLEAR
*
1'-6
"C
LR
*
1'-6
"
*
3'-8
"C
LEA
R*
1'-8
"C
LR
*
3'-6
"C
LEA
R*
3'-0"CLEAR
*
3'-0"CLEAR
*
6'-0"
7'-6 1/2"FLOOR
R20'-0"
FLOOR
3'-2
"C
LR
*
2'-8
"C
LR
*
5'-0"CLEAR
*
4'-6
"C
LEA
R*
3'-6
"C
LEA
R*
4'-0"CLEAR
*
3'-6
"C
LEA
R*
1'-0"CLR
*
4'-0"CLR
*
4'-4
"C
LEA
R*
1'-0"
*
5'-0"CLEAR
*
5'-0"CLEAR
*
P-7P-7
6D12
7D12
7'-6
"4'
-2"
*
2'-8"
MIN
.
CL
1'-1
"* CLR.
1
2
5
E
FF
L
FF
L
E
H
K
1'-1
0"
*
5'-6
"
4'-0" EQ.EQ. *
5"
*
1'-6
"
*
9" XCL
3
5
3D7
CPT.L.V.P.
L.V.P.RUN
14
P-7
2
EFFL
F FL E
H
K
CP
T.L.
V.P
.
L.V
.P.
RU
N
14
P-7P-7
2
E
FF
L
FF
L
E
H
K
CPT.L.V.P.
L.V.P.RUN
14
P-7P-7
2
E
FF
L
FF
L
E
H
K
CPT.L.V.P.
L.V.P.RUN
14
P-7P-7
2
E
FF
L
FF
L
E
H
K
CPT.L.V.P.
L.V.P.RUN
14
P-7P-7
2
E
FF
L
FF
L
E
H
K
CPT.L.V.P.
L.V.P.RUN
14
P-7
P-7
2
EFFL
F FL E
H
K
CP
T.L.
V.P
.
L.V
.P.
RU
N
14
P-7
P-7
2
EFFL
F FL E
H
K
CP
T.L.
V.P
.
L.V
.P.
RU
N
14
P-7
P-7
2
EFFL
F FL E
H
K
CP
T.L.
V.P
.
L.V
.P.
RU
N
14
P-7
P-7
2
EFF L
FF LE
H K
CPT.L.V.P.
L.V
.P.
RU
N
14
P-7
7'-4"
7'-4"
CPT.L.V.P.
CP
T.L.
V.P
.
CPT.C.T.
CONC.C.T.C
ON
C.
C.T
.
CPT.CONC.CPT.
C.T.
CP
T.C
.T.
CPT.C.T.
CPT.C.T.
CP
T.
C.T
.
CP
T.C
ON
C.
CP
T.C
.T.
CP
T.C
.T.
CPT.C.T.
CP
T.C
.T.
RO
D &
SH
ELF
5'-0"CLEAR
*
2'-4"SIDLT.
1'-8"SIDLT.
1'-8"SIDLT.
1'-6"
SIDLT.
1'-10"SIDLT.
1'-10"SIDLT.
3'-0"SIDLT.
101A
101B
101D
101C
120
3'-0" CASEDOPENING
110
111
152
109
114
115
108
113
117
118
123
122A
122B
132
133 12
7
131A13
1B
129 130 12
8
143
137
135
141
136142
140
139P-1
P-1P-2
P-2
P-2
P-2
P-2
P-3P-3
P-3
P-4
P-5
P-6
P-8
P-9
FD
FD
103
104
4
4
4
4
67 7 7 7
7
7
7
7
7
8
9
10
11(O.S
.C.I.)
W /
D
(BY O
THERS)
SERVER
12
12
12
12
13
13
13
14
K
15
15
15 15
15
16
17
18
1920
21
L.V.P.RUN
22
22
22
25(O.S
.C.I.)
REF
(O.S
.C.I.)
DW.
25(O.S
.C.I.)
REF
26
27
28
28
28
29
T
29
T
29
T
30 30 30
30
30
30
30
30
30 30
31
10D10
1D12
4D10
1D10
5D10
6D10
2D10
3D10
12D11
2D12
10D11
4D12
4D12
SIM.
3D13
13D12 14
D12
12D12
12D12 8
D11
11D11
9D11
1D11
3D11 2
D11
3D12
7D10
8D10
9D10
5D12 9
D12
1D13
2D13
4D11
5D11
6D11
7D11
11D12
11D12
10D12
A
A
A
B
B
B
BB
CC
C
D
D
D
D
D
GFF
G
J
J
L
L L
25(O.S
.C.I.)
REF
23
5'-0
3/4
"
2'-0"
*
5'-3 3/8"
ALIGN
12
12
10'-0
1/4
"
12 12
1212
31
4"
3D1
3D1
3D1
3D1
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
TI FLOOR PLAN
D2
Provide empty 3" i.d. PVC pipe & fittings to serve as a chasebelow the floor, connecting the base of Utilitech™ Walls to two(2) locations as shown. Vertical 3" i.d. pipe will connect to thehorizontal chase through the floor within the Utilitech™ Wallcabinet base and at all locations shown within the treatmentroom. The vertical 3" i.d. PVC pipe shall be finished flush withthe floor. All dimensions are to the center of the 3" diameter.Trim carpet to match i.d. of PVC & provide Doug Mockett FG-3floor grommets to finish within room, see plan note #11 thissheet. (Note: grommets must be provided prior to installationof dental equipment.) (See also plan & detail, sheet D5)
For typ. Utilitech™ Walls, see #4/D7 for framing.
"X" dim. from chair to Utilitech™ Wall to be 26" clear with chairin fully reclined position (verify w/ owner and Dent. Eq. Supp.)
Doug Mockett #TM1B-SSS trash drop. See details #5/D9, #6/D9 & #9/D9.
Shading indicates location for dental utilities (comp. air, vac.,etc.) at Utilitech™ Walls & chair bases as req'd. for dentaldelivery. Verify all reqts. w/ Dent. Equip. Supp. See sheet D7& detail on sheet D5.
For floor tile pattern see detail #4/D13.
Provide matching plastic laminate on back of all cabinets& backsplash crossing exterior windows. Typical.
Provide power for vacuum & compressor. Verifyrequirements w/ dent. equip. supp. (208-240v). Seeplan note #8.
Provide power, plumbing, & ventilation to exterior forwash/dry units. Verify all reqt's.
Bradley grab bars. See #3/D9 for specification & mounting details.
Bradley #235 recessed trash & towel disp.
Bradley #9663 recessed medicine cabinet.
Frame w/ 6" studs.
X-ray unit by dent. equip. supp. Verify power &blocking reqt's.
Dental vac. in sink base cab. See also int. elevation.
Provide power & blocking for wall-mounted monitor (O.S.C.I.).Verify all reqt's & mounting height/position w/ Owner.
Provide cold water supply line to model trimmer. Drain modeltrimmer to sink (above or below counter - verify w/ Owner &dent. equip. supp.). Verify reqt's w/ dent. equip. supp.
Under-counter lab vacuum by Owner. Providepenetrations in countertop for vacuum tubing at Dentalequipment per Owner's direction.
Provide 3 4" plywood backing behind gyp. board surface(see interior elevation).
Building column, verify w/ bldg. shell architect and struct.eng. Encase/conceal within wall framing as shown.
Wood shelving: provide (6) 3 4" part. bd. / melamineshelves at indicated width w/ K&V 80 84" shelf standards &K&V 180 adjustable shelf brackets. Mount shelf standards2'-6" apart (max.), bottom at 18" A.F.F. & locate over 2xblocking/framing.
KEYNOTES
1. DIMENSIONINGDimensions given to face of framing for interior partitions &face of finish or column lines at exterior walls (U.O.N.).Dimensions indicated with an asterisk (*) represent a clear'hold' dimension to face of finish/ gyp. board. Dimensionsreferencing building shell / exterior walls / demising wallsare for clarity only, refer to building shell drawings.
FLOOR PLAN NOTES
2. BUILDING SHELL DRAWINGSSee building shell drawings for all conditions and detailsrelating to building shell construction. Coordinatemechanical, plumbing, & electrical service information withbuilding shell drawings.
3. FLOOR MATERIALSSee Finish Schedule for specification of all floor materials &transition moldings. See plan for floor transition locations.
4. GLAZINGGraphic glazing indication represents recommendationonly. Refer to building shell drawings for exact type, size,& location of all exterior windows.
ACCESSORY KEYNOTES
Recessed dispensers to be provided as shown, see elevs. Frame walls accordingly androute all plumbing & electrical utilities around recessed areas. (See interior elevations).See #3/D9 for mounting details.
Bradley #5124 recessed double roll toilet tissue disp.
Bradley #155 recessed towel dispenser.
Bradley #987-36 recessed facial tissue dispenser.
Bradley Corp. (800.BRADLEY) www.bradleycorp.comDoug Mockett Co. (800.523.1269) www.mockett.com
Kohler #K-10552-2BZ 30" towel bar at 2'-10" A.F.F.
Doug Mockett #TL-27 R-3" table leg. Center on peninsula.
Kohler #K-10555-2BZ coat hook at 5'-6" A.F.F. Provide blocking in wall behind gyp. bd.
Provide wood blocking in walls for all accessories. General contractor must verify & providerated wood studs in walls as required by code.
5. FIRE EXTINGUISHERSProvide code required number of fire extinguishercabinets and fire extinguishers, UL-listed #4A-80BC.Provide 'AmeraProducts' Semi-Recessed Fire ExtinguisherCabinet #116-EL-SSF, stainless steel front finish (for a 10lb. dry chemical F.E.). Locations to be determined in thefield & approved by Owner. (www.ameraproducts.com)
7. ROD & SHELFAll rod & shelf combinations called for in plan but notelevated on the 'D' sheets to be "K & V" #770 coat rod ˞ flanges; melamine shelf w/ melamine edge.
8. COMPRESSOR/VAC.Provide acoustically isolated room for dental air compressorand vacuum units. Provide room with a floor drain. Providedrain in wall for vacuum unit per MFR directions. Contractorto provide all utilities to dental utility closet (C./V. room).Verify and provide all electrical, plumbing, vacuum pipingand special venting as directed by Dent. Equip. Supp.
9. O.S.C.I.Equipment item (owner supplied, contractor installed).Verify and provide all utility, mounting and supportrequired. Contractor to provide Owner with availableaccounts where Owner may purchase equipment atContractor pricing.
10.NATURAL GAS (N.G.)10.A. Provide natural gas at all locations indicated with the
symbol († NG) or († NG42). Symbol number indicates
mounting height in inches A.F.F. Installation byGeneral Contractor, and delivery nozzle as specifiedby Dent. Equip. Supp. Verify locations with Owner.Gas requirement relates to dental equipment &procedures only.
10.B. See drawings and specifications by others regardingall other gas requirements. This includes but is notlimited to water heater, fireplace, furnace, mainbuilding service, etc.
11.GROMMETSProvide grommets at countertops & floors as noted onplan & elevations. See Room Finish Schedule for all colorselections. -Trash Drop: Doug Mockett #TM1B-SSS, 6" dia/2" deep
-Floor: Doug Mockett #FG3 for 3" i.d. PVC-Wire Mgmt: Doug Mockett #EDP series, 2-1/2" hole (Seenote #6, Sheet D5 for quantity)
For wall detail see #1/D9.
Make-up air duct, see Keynote #10 on sheet D4.
ACCESSORY NOTES:
Multiple recessed dispensers at treatment rooms. See also interior elevations for locations.
Referenced on Sheet D2
5
4
3
2
1
6
7
8
9
10
11
12
13
14
15
16
17
18
19
21
22
20
A
B
C
D
E
F
G
H
J
K
L
Notes, dimensions, accessory keynotes & conditionsindicated in this trtmt room are typical all trtmt. rooms U.O.N.
See notes, dimensions, accessory keynotes & elevationreferences at typical treatment room. U.O.N.
GC to provide all utility requirements (water/drain/power/etc.)for distiller unit(s). Verify reqt's w/ Owner and unit supplier.
23
24
Bradley #1985 recessed towel dispenser.
6. COMPRESSED AIR (C.A.)Provide compressed air at all locations indicated with thesymbol († CA) or († CA
42), see elevs. & sheet D7. (Verify entiresystem w/ Owner & Dent. Equip. Supp.) Symbol numberindicates mounting height in inches A.F.F. Delivery nozzleshall be specified by Dent. Eq. Supp. Provided and installedby General Contractor. Verify all locations with Owner.
25 See note #23 on sheet D1. Coordinate cabinetry withrefrigerator door operation.
27 Suggested location for phone panel. Provide CDX plywoodto 8'-0" A.F.F. (Paint plywood to match wall color.)
26 Suggested location for electrical panel(s).
28 Fire Extinguisher and cabinet. See plan note #5 on this sheet.
29 Suggested locations for thermostats. See also #26, sheet D1.
Provide Master "shut-off" switches to suite - (1) for water &(1) for compressor/vacuum at this location (Vest). (Verifyswitch voltage for comp./vac.) Use 'Red Jewel' typelighted toggle switches for master shut off. By 'Bryant'Electric (800-323-2792) or equal: #4901PLR120.Coordinate with Dental Equipment Supplier.
See Keynote #1/D2, plan note #11/D2, & plan note #6/D5 for additional grommets.
1/4" = 1'
FLOOR PLAN0"
30 Provide 3/4" blocking strips under countertop as req'd forinstallation/mounting of under-counter keyboard trays(O.S.C.I.). Verify dimensions and reqt's w/ tray mfr. Installper mfr. recommendations and directions. Verify traylocations in field with Owner.
31 General Contractor to verify & provide return air at ceiling &11
2" clear door undercut for ventilation of electroniccomponent (server) closet and distiller closet.
( not used )
9'-0"
1
VEST.101
ELEV.103
UTIL.104
STAIR102
GREET.105
WAITING106
KIDS107
CTRL.108
BUS.109
R.R.110
OFC.111
HALL112
LAB113
CL.114
FIN.115
HALL116
CEREC117
DIST.118
REAPPT.119
HALL120
HALL121
CNSLT.122
SVR.123
PAN124
STERIL.125
HALL126
HALL127
STAIR128
C./V.129
VEST.130
ELEC131
CL.132
SUPP.133
HALL134
HALL135
R.R.136
C.A.137
PAT. ED.138
R.R.139
R.R.140
JAN.141
R.R.142
TRTMT.143
TRTMT.144
TRTMT.145
TRTMT.146
TRTMT.147
TRTMT.148
TRTMT.149
TRTMT.150
TRTMT.151
TRTMT.152
7'-0"
13
9'-0"
2
10'-0"
1
EQ.
CL
EQUAL
EQUAL
CL
EQUAL
EQUALEQUAL
CL
EQ
UA
LE
QU
AL
EQ
UA
LE
QU
AL
C L
C LC L
EQ
UA
LE
QU
AL
2'-0"
EQ
UA
LE
QU
AL
R10'-6
"
MAX
2
4'-0"EQ. EQ.
4'-0
"E
Q.
EQ
.
19
19 19
19
1
1
2
2
2
1
1
3'-8"
1'-4"
3'-8
"1'
-4"
1"
1"
7'-6"
7'-6"11
11
11
9'-0"
1
11 12
1
1
1
1
1
1
1
2
7'-0"13
12
7'-6"
1'-0"
9'-0"
1
127'-0"13 7'-6"
13
13
10 10
101
1
1
1
2
1
2
127'-6" 7'-6" 1212
12
7'-6
"
12
12
7'-6
"
10"
7'-2
"
1'-8" 4"
4"
1'-7
1 2"
11 2"
CL
5
6
98
19'-0"
4
7
320 20 20 20
20
20
20
20
20
12
12
1
19'-0"
19'-0"
14 1414
14
15
16
181818
18
7'-0"
13
4'-0"
2'-6"
1'-6"
1'-6"
4'-0" X 2'-6" TWO LEAFBAUCO.PLUS II DRYWALLCEILING ACCESS PANELBY ACCESS PANELSOLUTIONS INC.877-592-0033 -
1'-6" X 1'-6" BAUCO.PLUS IIDRYWALL CEILINGACCESS PANEL BYACCESS PANELSOLUTIONS INC.877-592-0033
NOTE: THESE NEARLY INVISIBLE CEILING ACCESSPANELS ARE REQUIRED FOR SERVICING ANDREPLACEMENT OF THE MECHANICAL UNITABOVE, COORDINATE SIZE AND LOCATION OFPANELS WITH MECHANICAL CONTRACTOR PRIORTO ORDERING AND INSTALLATION. SUBMIT SHOPDRAWINGS FOR REVIEW AND APPROVAL BYARCHITECT. PROVIDE CROSS-BRACE WIRING
FOR RIGID LATERAL SUPPORT
(REFER TO ARCH. DRAWINGS)24"X24" LAY-IN CEILING
(ALL 4 PANEL CORNERS)
SUPPORT/BLOCKING OF (2) SHEETS
GRID TO FIX PLYWOOD PANELS.SCREW THROUGH SIDE OF T-BAR
TOGETHER. ABOVE LAY-IN CEILING24"X24"X3/4" PLYWOOD, SCREWED
PANEL.
INDEPENDENTLY TIE PLYWOODSUPPORT TO STRUCTURE ABOVE.
(TYP.)
CEILING GRID CHANNELS.MAINTAIN 4" CLEARANCE (MIN.) TO
DIMENSIONS GIVEN.
'SYVUE' CEILING BRACKET (OR EQUAL)MOUNT PER CENTER POINT
CEILING TILE.
WHITE GROMMET ATHOLE/PENETRATION AT
MOUNTING PLATE ATTACHES
BLOCKING - FIX TO BLOCKING.TO POST FROM TOP SIDE OF
SUPPORT BELOW CEILING.
TELESCOPING POST TO MOUNTINGPLATE ABOVE CEILING & MONITOR
TI REFLECTEDCEILING PLAN
D3
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
Lay in tegular acoustical tile ceiling.
Gypsum board finish ceiling.
Dimension from F.O. Utilitech™ Wall to C.L. of monitormount.
Provide blocking for ceiling mounted dental light.Verify all conditions w/ Dent. Equip. Supp.
Structurally tied plywood backing above (1) ceiling tile.See detail #1/D3.
Syvue PV ceiling monitor mount for flat panel monitor(O.S.C.I.). Bottom of monitor at 6'-8" A.F.F.www.syvue.com
KEYNOTES
Notes, dimensions & conditions indicated in thistreatment room are typical in all trtmt. rooms U.O.N.
Referenced on Sheet D3
LEGENDRecessed fluorescent light fixture, 2x4troffer.
Recessed fluorescent light fixture, 1x4troffer.
Surface mounted fluorescent light fixtureRecessed fluorescent can light fixture
Exhaust fan, see specification on Sheet D5.
Suggested location for 'background sound'speaker (by others). Locate volume controlsin field w/ Owner. Provide volume controljunction box & conduit to above ceiling ineach room where speakers are located perthe direction of Owner. Verify allcomponents and locations w/ system vendor.
Gyp. board valance above casework.Valance shall be built out from the wall 1"less than the cabinet depth.
Ceiling mounted Exit Light
Emergency Light
1. CEILING HEIGHTSAll ceiling heights are 9'-0" A.F.F. unless otherwise noted.
REFLECTED CEILING PLAN NOTES
2. VALANCESGyp. bd. valances above wall cabinets (where drawn) shall be built outfrom the wall 1" less than the cabinet depth.
3. LOWERED CEILING HEIGHTSCeiling heights in Lab, Toilets & Closets may be lowered to 8'-0" A.F.F.to accommodate mechanical system components, etc.
Lay in acoustical tile ceiling. LAT ceilings tobe a 24"x24" tegular type tile. See roomfinish schedule for specification.
4. EXISTING (BUILDING SHELL) CONSTRUCTION COORDINATIONGeneral Contractor must field verify all indicated ceiling heights with existingbuilding /building shell construction for possible obstructions. Bring anyconflicts to the attention of Unthank Design Group for clarification.
5. DIMENSIONINGDimensions on Reflected Ceiling Plan are given to the face of Gyp. Bd.(U.O.N.)
6. EXTRA CEILING TILEGeneral Contractor to provide (1) full box of extra ceiling tile for futureuse by Owner.
7. MONITOR MOUNTSAll treatment room ceiling monitor mounts/brackets to be set so that thebottom of the monitor is at 6'-8" A.F.F.
Dimension from C.L. of room /chair to center point ofmonitor mount. Verify offset to Dr's side of room.Ceiling mount to clear ceiling grid by 4" all sides.
Provide all data, cable & power connections to locationabove ceiling for monitor operation. See sheet D5.
Gyp. bd. finish header at 7'-0" A.F.F.
Gyp. bd. bulkhead with soffit at 7'-6" A.F.F., matchprofile of cabinet /countertop below.
Gyp. bd. bulkhead with soffit at 7'-6" A.F.F.
Gyp. bd. bulkhead with soffit at 7'-0" A.F.F.
Bulkhead overhangs wall by 1".
See sheet D2 for center point location.
Make-up air duct, see Keynote #10 on sheet D4.
( not used )
'Tech Lighting' MonoRail system, see specification onSheet D4.
Light location(s) along MonoRail system
Ceiling and lighting conditions within this room are notdetailed on "D" sheets.
4
3
2
1
5
6
7
8
9
10
11
13
12
14
15
16
17
18
19
20 See keynotes, dimensions & references at typicaltreatment room.
This icon designates points of importantcoordination with dental equipment supplycompany representative. Notes describingspecific coordinating effort follow.
1/4" = 1'
REFLECTED CEILING PLAN0"
Recessed fluorescent wall wash can light fixture
1TCIRC
3
EQ.
CL
EQUAL
EQUAL
CL
EQUAL
EQUALEQUAL
CL
EQ
UA
LE
QU
AL
EQ
UA
LE
QU
AL
C L
C LC L
EQ
UA
LE
QU
AL
2'-0"
EQ
UA
LE
QU
AL
R10'-6
"
4'-0"EQ. EQ.
4'-0
"E
Q.
EQ
.
3'-8"
1'-4"
3'-8
"1'
-4"
1"
1"
1'-0"
10"
7'-2
"
1'-8" 4"
4"
1'-7
1 2"
11 2"
CL
B B
**
J
A A
1
28
VEST.101
ELEV.103
UTIL.104
STAIR102
GREET.105
WAITING106
KIDS107
CTRL.108
BUS.109
R.R.110
OFC.111
HALL112LAB
113CL.114
FIN.115
HALL116
CEREC117
DIST.118
REAPPT.119
HALL120
HALL121
CNSLT.122
SVR.123
PAN124
STERIL.125
HALL126
HALL127
STAIR128C./V.
129
VEST.130
ELEC131
CL.132
SUPP.133
HALL134
HALL135
R.R.136
C.A.137
PAT. ED.138
R.R.139
R.R.140
JAN.141
R.R.142
TRTMT.143
TRTMT.144
TRTMT.145
TRTMT.147
TRTMT.148
TRTMT.149
TRTMT.150
TRTMT.151
TRTMT.152
B B
**
J
A A
H HH
B B
**
J
A A
B B
**
J
A A
TRTMT.146
B
B
* *
J
A
A
B
B
* *
J
A
A
B B
**
J
A A
B
B
* *
J
A
A
B
B
* *
J
A
A
9 9 9 9
9
9
9
9
9
H
H
* *
B
B
A
A
J
1T 1T
H H
G
H H H H H HCIRC
EM
EX2
EX1
H
H H
3 CIR
C
S
S
S
S
M
S
10
12
1212
12
11
H
H
H
H
H
H
H
1T 1T
1T
1T
1T
1T
CIRC
CIRC
H
2T
6
D
D H1
H1
H1
H1
H1
H1
H1
H1
DIM
R R
R
R
S
R R
RR
R
RP
F F
F
P
H1
H1
DIM
C
C
R
R
R
P
P
R
HSR
S
3 CIR
C
F F
FFF
P
P
P
P P P
P P PP P
4
F
RH
1H
1
H1
H1
R
DIM
H
2T
5
H
2T
5
S
2T2T
66
H
P P P PP
HHH
C
CC
C
C
R R
HHHHHHH
H
H
H
HK
K
K
CIRC
H
H H
H
H H
HH
H
H
H
CIRC
NIGHTLIGHT
NIGHTLIGHT
NIGHTLIGHT
NIGHTLIGHT
H
R
HHHH
H
H H
H
H H H H H
K
K
EEE
R RP
4
LLLLL
L
L
L
3T3T4T
5T 7
EM
EM
EM
EM
EM
EM
EX1
EX1
EX1
EX1
EX2
EX2
P
DIM
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
TI LIGHTING PLAN
D4
1. CIRCULATION LIGHTSSwitch the lighting group marked CIRC at two switch locations marked$CIRC.
LIGHTING PLAN NOTES
2. BACKGROUND SOUND'Background Sound' system by others. Verify all components, locations &requirements with system vendor/Owner. Locate volume controls in fieldwith Owner. Provide volume control in each room where speakers arelocated, and place conduit and junction boxes per the direction of Owner.
3. CIRCUITING COORDINATIONLighting Plan is not intended to show circuiting. Rather, indicatesswitch patterns. See drawings by Others for circuiting.
4. FIELD MEETINGSet up field meeting with Owner before starting wiring work; review allswitch, outlet & fixture locations; mark exact locations. Do not install byscaling locations off plans. The Owner may make reasonableadjustments in location, before start of wiring, from that shown on planswithout additional expense.
12.EMERGENCY & EXIT LIGHTINGCeiling & lighting plans show suggested locations for exit & emergencylighting. Provide specified fixtures as required to meet all buildingcodes & local ordinances. See fixture schedule below.
7. EXTERIOR LIGHTINGSee drawings by Others for all conditions and specifications relating toexterior lighting fixtures.
Center on sink.
Center on sink at 6'-8" A.F.F.
Provide junction box for ceiling mounted dental light.(Consult with Owner) Verify power & blocking reqt's w/Dent. Equip. Supp.
T.V. monitor hookups at ceiling. See sheets D3 & D5.Typical all treatment rooms U.O.N.
KEYNOTES
Center on wall at 6'-8" A.F.F.
Referenced on Sheet D4
1) Schedule item designations refer to the "Lithonia Lighting" Product Selection Guide, latest edition.
2) Exhaust fans and washer/dryer units are to be vented to the outside.
LIGHTING NOTES:
3) All fluorescent light tubes in Treatment Rooms shall have C.R.I. of 90+.
9. CODE COMPLIANCEAll light fixtures shall meet applicable codes, including the NationalElectric Code (NEC) & International Energy Conservation Code (IECC).Contractor to verify requirements & provide compliant fixtures.
4) Verify & provide IC rated fixtures as required, see plan note #10/D4.
LEGEND
10.IC RATED FIXTURESIt is the General Contractor's responsibility to determine all InsulationContact (IC) rating requirements. Where IC rated light fixtures arerequired, General Contractor should contact Unthank Design Group foralternate fixture specifications prior to pricing the project.
11.SPECIALIZED DENTAL LIGHTING EXEMPTIONAll type 'B' fluorescent light fixtures within treatment rooms are anintegral part of specialized procedural dental lighting; fixtures exemptfrom energy audit/compliance calculations, reference 2006 IECC505.5.1
6. TILE WAINSCOTAll switches in Toilet Rooms to be recessed into tile wainscot. Top ofswitch plate to be even with the bottom of the bullnose tile. Seeelevations.
8. OWNER APPROVALElectrical contractor to provide Owner with cut sheets for all 'T' typefixtures for Owner approval in writing prior to ordering.
Center wall sconces on Utilitech Wall, mount at 72"A.F.F. (J-Box to be recessed in center stud as req'd.)
'L' type is under-counter puck light. See section #9/D8& elevs. Typical.
Make-up air duct; at Compressor/Vacuum locationprovide supply duct of 6" insulated-flex to grill 4" A.F.F.Flex to run through ceiling & acoustical ceilinginsulation - no return. Strap duct to corner location.
Make adjustable thermostat accessible below ceiling.
1
2
3
4
5
6
7
10
11
9 See keynotes, dimensions & references at typicaltreatment room.
Notes, dimensions & conditions indicated in thistreatment room are typical in all trtmt. rooms U.O.N.
8
*Switch location
Indicates split switching (inboard-outboard)of fluorescent light fixtures.
DIM Indicates dimmer to be provided for lightfixtures as indicated.
Dental Equipment Supplier Coordination:This icon designates points of importantcoordination with dental equipment supplycompany representative. Notes describingspecific coordinating effort follow.
CIRC General circulation lights. See lighting plannote #1.
1/4" = 1'
LIGHTING PLAN0"
5. SWITCH & COVER PLATESColor of all switches, elec. outlets and cover plates shall be as specifiedin the Room Finish Schedule & approved by the Owner.Switches to be rocker type. Receptacles to be decora type.
Ceiling and lighting conditions within this room are notdetailed on "D" sheets.
12
CENTER POINTDIMENSIONS TO
FLOOR GROMMET.
(FULLY RECLINED)RECOMMENDED
*EXPOSED PORT LOCATIONS
WITH FLOOR. TRIM CARPETTO I.D. OF PVC. - FINISH W/
TO HAVE PVC CUT FLUSH
* CONC. SLAB OR SUB-FLOOR
SINGLE HORIZ. RUN - DO NOT BREAK
NOTE:
MAY VARY. EACH TREATMENT ROOMMUST BE VERIFIED.
CHAIR MODELS AND DIMENSIONS
F.O
. WA
LL
CABINET BOTTOMLEAD PORT OCCURS IN
FLOOR PANEL IN CAB.)(ACCESSED W/ REMOVABLE
MUST VERIFY THAT
COVER FLOOR PORTS.PEDESTAL BASE WILL NOT
TM"UTILITECH "WALL
DENTAL CHAIR
7'-6"4'-2"
6'-4" 26" TO 30"
UNDER-FLOOR EMPTY CHASEOF 3" I.D. PLUMBING PVC, NOELECTRICAL WIRING (W/ 90'S& 'T' AS INDICATED).
DUPLEX RECEPTACLEIN UTILITY BOX.
RECESSED DENTAL UTILITYJUNCTION BOX. (PROVIDED BYDENTAL EQUIP. SUPP. ORCUSTOM FROM ELEC. BOX).PROVIDE DENTAL UTILITIES TOJUNCTION BOX PER DIRECTIONOF DENTAL EQUIPMENTSUPPLIER.
PVC PORT WITHINUTILITY BOX.
CENTERLINE OFDENTAL CHAIR
RECESSED DENTAL UTILITYJUNCTION BOX (PROVIDED BYDENTAL EQUIP. SUPP. OR CUSTOMFROM ELEC. BOX). PROVIDEDENTAL UTILITIES TO JUNCTIONBOX PER DIRECTION OF DENTALEQUIPMENT SUPPLIER.
NOTE:VERIFY ALL DIMENSIONS &CONDITIONS WITH DENTALEQUIPMENT SUPPLIER.
COORD. SO THATALL UTILITYBOXES DO NOTCONFLICT WITHCHAIR BASE 2"
CL
RECESSED FLOORELEC. OUTLET.
PVC UNDER-FLOOR CHASE
L=18" L=18" L=18" L=18" L=18" L=18" L=18" L=18" L=18" L=18" S=12" S=12"
S=
12"
L=18
"L=
18"
L=18
"L=
18"
L=18
"L=
18"
L=18
"L=
18"
L=18
"L=
18"
L=18"U=13"
L=18"U=13"L=
24"
L=12
"U
=12
"
C=
24"
U=
15"
C=24"U=15"
L=12"U=12"
C=24"U=13"
L=24"U=13"
C=
24"
U=
13"
C=
24"
U=
13"
S=12"
S=
12"
S=
12"
C=
30"
C=24"U=15"
C=24"U=13"
C=24"U=13"
C=
24"
U=
18"
C=
24"
U=
15"
U=
18"
S=18"
L=24"S=12"
L=24
"U
=13
"
L=24
"U
=13
"
L=24"L=
24"
L=24
"
L=24
"
L=18"
L=24"S=18"
L=30
"U
=18
"
L=12"S=12"
C=12"
C=
30"
C=24"U=15"
S=12"S=
12"
L=24"U=15"
L=24"U=13"
L=24
"U
=13
"
L=24
"U
=13
"L=
24"
U=
13"
C=
30"
C=
12"
C=30"
C=12"
C=
20"
L=24
"U
=18
"
22
7'-6
"4'
-2"
CL
TV
4-PLEX
40GFCI
40GFCI
4-PLEX
1
9 9
10
2
3
44
5
7
8
6
VEST.101
ELEV.103
UTIL.104
STAIR102
GREET.105
WAITING106
KIDS107
CTRL.108
BUS.109
R.R.110
OFC.111
HALL112
LAB113
CL.114
FIN.115
HALL116
CEREC117
DIST.118
REAPPT.119
HALL120
HALL121
CNSLT.122
SVR.123
PAN124
STERIL.125
HALL126
HALL127
STAIR128
C./V.129
VEST.130
ELEC131
CL.132
SUPP.133
HALL134
HALL135
R.R.136
C.A.137
PAT. ED.138
R.R.139
R.R.140
JAN.141
R.R.142
TRTMT.143
TRTMT.144
TRTMT.145
TRTMT.146
TRTMT.147
TRTMT.148
TRTMT.149
TRTMT.150
TRTMT.151
TRTMT.152
TV
4-PLEX
40GFCI
40GFCI
4-PLEX
5
TV
4-PLEX
40GFCI
40GFCI
4-PLEX
5
TV
4-PLEX
40GFCI
40GFCI
4-PLEX
5
TV
4-PLEX
40GFCI
40GFCI
4-PLEX
5
TV
4-PLEX
40GFCI
40GFCI
4-PLEX
5
TV
4-PLEX
40GFCI
40GFCI
4-PLEX
5
TV
4-PLEX
40GFCI
40GFCI
4-PLEX
5
TV
4-PLEX
40GFCI
40GFCI
4-PLEX
5
TV
4-PLEX
40GFCI
5
4-PLEX
40GFCI
GFCI
Y
23
X
X
42GFCI
42GFCI
Y
X
X42
GFCI
42GFCI
10
60
TV60
21
46GFCI
20 9
46GFCI
19
18
68
9
46GFCI68
9
4-PLEX
14
46
TV60
21
60
TV60
21
60
46GFCI
18
60TV60
21
60
4-PLEX
13
4-PLEX13
11
4-PLEX
4-PLEX
13
4-PLEX
13
4-PLEX
11
4-PLEX
11
11
4-PLEX
11
4-PLEX
13
4-PLEX
13
4-PLEX
13
4-PLEX
13
42GFCI
X4-PLEX
13
4-PLEX
13
11
GFCI52
GFCI46
4-PLEX
Y
GFCI46
4-PLEX
GFCI46
4-PLEX46
31 15
GFCI46
4-PLEX
GFCI46
4-PLEX
46
10
46
31
GFCI
30
12
4-PLEX
14
46TV68
684-PLEX
4-PLEX
25
26
8
4-PLEX
14
46
GFCI
Z
24
Y
46GFCI
18
46GFCI
10
46GFCI
46GFCI
46GFCI46 46
GFCI GFCI
17
46 46GFCI GFCI
17
GFCI
1616
GFCIGFCI
16
TR
27
28 28 28 28
28
28
28
28
28
9
9
26262626 2626 2626 2626
26
26
26
26
26
26
26
26
26
26
46
46
46
46 46
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
TI POWER PLAN
D51. FLOOR CHASE DETAIL
0"
1/2" = 1'
TV
etc.,, TV
1 1/2" = 1'
0"
TRTMT. RM. FLOOR DET.2.
46
1. MOUNTING HEIGHTInstall all electrical outlets at 18" A.F.F. (U.O.N.) or as directed as'typical' within treatment rooms. Where numbers are shown adjacent tothe electrical outlet symbol, the number shown indicates the height (ininches) at which the electrical outlet shall be centered above thefinished floor.
POWER PLAN NOTES
2. COMPUTER SYSTEM COORDINATIONVerify with Owner all computer requirements; i.e., dataports, dedicatedcircuits, additional telephone lines, conduit runs, if any.
6. HOLES IN COUNTERTOPSProvide approx. (24) 21
2" dia. holes (+ grommets) in countertops for'wire management' at locations as directed by Owner. Field verify withOwner. Cut & place at no charge. See note #11 sheet D2 for grommetspecification.
4. FIELD MEETINGSet up field meeting with Owner before starting wiring work; review allswitch, outlet, fixture, and electrical panel locations; mark exactlocations. Do not install by scaling locations off plans. The Owner maymake reasonable adjustments in location, before start of wiring, fromthat shown on plans without additional expense.
11.COMPRESSOR & VACUUMProvide power for compressor & vacuum (C./V. room). Verify allrequirements with Dental Equipment Supplier. See also plan note#8, sheet D2.
7. EXTERIOR POWERSee drawings by Others for all conditions and specifications relating toexterior power requirements.
Do not place electrical or plumbing lines in areas forrecessed dispensers. See plan sheet D2 & interiorelevations.
Provide power & T.V. cable connections at ceiling formonitor (O.S.C.I.) (See sheet D3 - Ceiling Plan forlocation). Verify cable circuiting & any specialswitching with Dent. Equip. Supp.
KEYNOTES Referenced on Sheet D5
8. ELECTRICAL PANELProvide minimum 400 AMP service panel, unless directed otherwise byElectrical Engineer of Record. Electrical panel selection must includeloads for all dental equipment. Verify & coordinate with DentalEquipment Supplier.
LEGENDDuplex electrical outlet
Four-plex electrical outlet
Switched duplex electrical outlet
9. COORDINATION WITH OTHERSOffice 'technology' system cabling & components of Voice, Data &Background Sound to be by Others. General Contractor to provide allboxes, j-boxes, conduit, required blocking / support for rough in. Stubrough in conduit 4 inches above finished ceiling elevation, typ. Voice &data to be located within single boxes at locations indicated. (See alsosheet D3). Vendor / Technology consultant drawings will govern whenin conflict with these Architectural drawings.
10.COMBINATION (GANG) BOXESTo the greatest extent possible, provide combination (gang) boxes forvoice, data, power, etc. Verify & coordinate availability and selectionwith Owner.
3. PHONE SYSTEM COORDINATIONPhone system by others. General contractor to coordinate allconditions & provide access to project as required by phone/soundcontractors retained by Owner. Provide all required electrical power tophone board/ panel system.
Outlets & ports indicated in this gang condition to bemounted below counter and coordinated with hole incountertop for 'wire-management'. Outlets & ports at22" A.F.F. See power plan note #6, this sheet.
3
2
4
11
Switch location
Switched four-plex electrical outlet
Special equip. power connection (verify reqt's)
Floor electrical outlet (verify reqt's)
Telephone outlet
Cable television outlet
Dataport for computer wiring
Outlets at ceiling (Items shown dashed atunique location as called for)
Numbers adjacent to symbol indicate mounting heightA.F.F. (in inches). Where number is not present,mounting height is 18" A.F.F.
Provide empty 3" i.d. PVC pipe & fittings to serve as achase below the floor, connecting the base of Utilitech™Wall to two (2) locations as shown. Vertical 3" i.d. pipewill connect to the horizontal chase through the floorwithin the Utilitech™ Wall cabinet base and at alllocations shown within the treatment room. The vertical3" i.d. PVC pipe shall be finished flush with the floor. Alldimensions are to the center of the 3" diameter. Trimcarpet to match i.d. of PVC & provide Doug MockettFG-3 floor grommets to finish within room (see plannote #11 sheet D2 for specification). (Note: grommetsmust be provided prior to installation of dentalequipment.)
1
Notes, dimensions & conditions indicated in thistreatment room are typical in all trtmt. rooms U.O.N.
6
Provide three (3) 4-plex & two (2) duplex outlets at allUtilitech™ Wall locations. Refer to sheet D7 for exactoutlet placement.
5
Doorbell-type remote switch for x-ray activation. Verifyall requirements with Dental Equipment Supplier.
7
Dedicated circuit for x-ray unit. Verify all requirementswith Dental Equipment Supplier. 208-240v.
8
In cabinet (upper/lower, see height noted).
Wall-mounted telephone outlet.
9
10
Outlets & ports indicated in this gang condition to bemounted below counter and coordinated with hole incountertop for 'wire-management'. Outlets & ports at28" A.F.F. See power plan note #6, this sheet.
12
13
14
Provide switched outlet for under-counter lab vacuum(by Owner). Provide penetrations in countertop forvacuum tubing at dental equip. per Owner's direction.
15
GFCI Ground Fault Circuit Interrupter.
Dedicated circuit in cabinet for dental equipment (byOwner). Verify all reqt's with Dent. Equip. Supplier.
16
Provide redundant dedicated circuit gangs forcountertop sterilizer (by Owner). One is 110V; one is208-240V (20 AMP -verify). Verify all reqt's with Dent.Equip. Supplier.
17
For refrigerator (by Owner).18
For under-counter dishwasher (by Owner).19
Provide switched outlet for disposal.20
Provide power, cable T.V. & blocking for wall mountedT.V. (O.S.C.I.). Verify all reqt's & mounting height.
21
Provide Master "shut-off" switches to suite - (1) for water &(1) for compressor/vacuum at this location (Hall). (Verifyswitch voltage for comp./vac.) Use 'Red Jewel' typelighted toggle switches for master shut off. By 'Bryant'Electric (800-323-2792) or equal: #4901PLR120.Coordinate with Dental Equipment Supplier.
22
Provide dedicated circuit for Washer/Dryer unit(s)(by Owner). Verify power reqt's, 208-240V.
23
Provide power to compressor & vacuum at this location.Verify reqt's with Dent. Equip. Supp. (208-240V) Seeplan note #8 sheet D2.
24
Provide power, data & phone outlets for phone system/computer server closet. Verify all reqt's with equip.suppliers. Coordinate all outlet locations & mountingheights with free standing equipment & utility panels.
25
Provide power & cable for stereo/digital music serviceon component rack (by Others). Verify with Owner.
26
General Contractor to verify & provide return air atceiling & 11
2" clear door undercut for ventilation ofelectronic component closet.
27
28
(not used).29
30
This icon designates points of important coordinationwith dental equipment supply company representative.Notes describing specific coordinating effort follow.
CPU location. Provide outlets & ports as indicated inthis gang condition, to be mounted below counter andcoordinated with hole in countertop for'wire-management'. Outlets & ports at 22" A.F.F. MountCPU under counter with CPU holder as specified bytechnology consultant (verify with tech. consultant).See power plan note #6, this sheet.
CPU location. Provide outlets & ports as indicated inthis gang condition, to be mounted below counter andcoordinated with hole in countertop for'wire-management'. Outlets & ports at 28" A.F.F. MountCPU under counter with CPU holder as specified bytechnology consultant (verify with tech. consultant).See power plan note #6, this sheet.
12.RECESSED DISPENSER COORDINATIONVerify locations of all recessed dispensers indicated in these drawings,see Sheet D2. Power, phone , data & plumbing lines shall not interferewith rough-in areas for dispensers. All utility lines improperly placedwill be corrected at no additional cost to owner.
Dedicated circuit for porcelain glazing oven (by D.E.S.).Verify all reqt's with Dent. Equip. Supplier.
31
See notes, dimensions, accessory keynotes & elevationreferences at typical treatment room. U.O.N.
Recessed floor electrical outlet for dental chair withindental utility junction box, centered on chair. Verify allreqt's with Dent. Equip. Supp. See details #1 & 2/D5.
1/4" = 1'
POWER PLAN0"
Tamper-resistant duplex outlet (verify w/ local codes)TR
5. SWITCH & COVER PLATESColor of all switches, elec. outlets and cover plates shall be as specifiedin the Room Finish Schedule & approved by the Owner.Switches to be rocker type. Receptacles to be decora type.
Provide power receptacle(s) for distiller unit(s). Verifyall reqt's with Owner and unit supplier.
D WOOD FRAMEFOR 1-3/4" DOOR(S)
PAINTHARDWOOD
4D6
1 3/4" DOORFLUSH SLABSOLID CORE
54 1 3/4" 9-LITE DOORTRUSTILE #FL900 (OR EQUAL)STANDARD HIP MULLIONSSTILE/RAIL/GLASSTEMP. GLASS (TRUE DIVIDED-LITE)SHADING IND. "3-FORM" 1/4" VARIATHATCH 50% CENTER INSERT W/SANDSTONE FINISH BOTH SIDES. (SUBMITSAMPLE FOR APPROVAL BY OWNER)
5D6
112"
3"
112"
TYP. WINDOW TRIM
SIM
A
A
4D6
B
NOTE:
RETURN, CONTACT UNTHANKIF WINDOW HAS GYP BD. CONTRACTOR TO VERIFY;
DESIGN GROUP (402-423-3300)
7'-0
"
1 1-34" 9-LITE DOORTRUSTILE #FL900 (OR EQUAL)STANDARD HIP MULLIONSSTILE/RAIL/GLASS W/ SIDELIGHTSTEMP. GLASS (TRUE DIVIDED-LITE)& CLEAR GLASS TRANSOM PANELSSHADING IND. "3-FORM" 1/4" VARIATHATCH 50% CENTER INSERT W/SANDSTONE FINISH BOTH SIDES. (SUBMITSAMPLE FOR APPROVAL BY OWNER)
3 1-34" 9-LITE DOORTRUSTILE #FL900 (OR EQUAL)STANDARD HIP MULLIONSSTILE/RAIL/GLASS W/ SIDELIGHTTEMP. GLASS (TRUE DIVIDED-LITE)SHADING IND. "3-FORM" 1/4" VARIATHATCH 50% CENTER INSERT W/SANDSTONE FINISH BOTH SIDES. (SUBMITSAMPLE FOR APPROVAL BY OWNER)
7D6
6D6
R.O.(SEE NOTE #8, THIS SHEET)
C
7'-0
"
PAINTHARDWOOD
CUSTOM WOOD FRAMEFOR DOOR/SIDELIGHT
R.O.(SEE NOTE #8, THIS SHEET)
A
CONTRACTOR MUST FIELD VERIFY WITHACTUAL AVAILABLE FRAMING DIMENSIONS.(TYP.) SEE NOTE #8 THIS SHEET.
7'-0
"8'
-6"
PAINTHARDWOOD
CUSTOM WOOD FRAMEFOR DOOR/SIDELIGHTS/& TRANSOMS
E
PAINTHARDWOODPOCKET DOOR ASSEMBLYWOOD FRAME WITH
7'-0
"
2D6
A
A
4D6
5D6
A
A
A
A
1D6
A
6D6
7D6
A
2'-6
"
2'-6
"
2 1-34" 9-LITE DOORTRUSTILE #FL900 (OR EQUAL)STANDARD HIP MULLIONSSTILE/RAIL/GLASS W/ SIDELIGHTSTEMP. GLASS (TRUE DIVIDED-LITE)& CLEAR GLASS TRANSOM PANELSSHADING IND. "3-FORM" 1/4" VARIATHATCH 50% CENTER INSERT W/SANDSTONE FINISH BOTH SIDES. (SUBMITSAMPLE FOR APPROVAL BY OWNER)
2D6
A
6D6
7D6
A
R.O.(SEE NOTE #8, THIS SHEET)
7'-0
"
8'-6
"
2'-6
"
B
PAINTHARDWOOD
CUSTOM WOOD FRAMEFOR DOOR/SIDELIGHT/& TRANSOMS
6 1 3/4" 9-LITE DOORTRUSTILE #FL900 (OR EQUAL)STANDARD HIP MULLIONSSTILE/RAIL/GLASSTEMP. GLASS (TRUE DIVIDED-LITE)
4D6
5D6
A
A
C. UTILITECH WALL TRIMA. TRIM
3"
3/4"
3/4"2
1/2"
BUILDING COMPONENTS.CASING, COORDINATE ALLDO NOT TRIM OR SCRIBE
NOTES:
JOINING (TYP.)TO INCLUDE PLATE/BISCUITJOINTS IN PAINTED TRIM
B. WINDOW STOOL/SKIRT
3/4"
3"
1"CORNERSEASED
3/4"
3"
1"CORNERSEASED
TYP. INT. DOOR JAMBTYP. INT. DOOR HEAD
EQ.EQ.EQ.EQ.NOTE:
'CENTERED' TO ACCOMODATE
OF STOP (TYP.)DOOR ON EITHER SIDE
STOP IS TO BE LOCATED
NOTE:VERIFY ACTUAL WALL
CONDITION. MATCHW/ FRAME DEPTH. (TYP.)
THICKNESS W/ ACTUAL
4D6
5D6
2D6 DOOR & SIDELIGHT
1D6 MAIN WAITING DOORWAY
1/4" COVERSTRIP
CASINGSTRIP1/4" COVERCASING
STRIP1/4" COVER
CASINGCASING
ROOM SIDE, TYP.
ROOM SIDE, TYP.ROOM SIDE, TYP.
ROOM SIDE, TYP.
STILE & RAIL FRAME
"SHAKER STYLE"
QUARTER ROUNDINTERIOR EDGE.
OUTSIDE CABINET
INSIDE CABINET
3D6
NOTES:DETAIL FOR CAB. DOORS & LARGER PANELS ONLY.
DRAWER FRONTS TO BE SOLIDHARDWOOD TO MATCH.
STILES TO BE 2-1/4" WIDE.RAILS TO BE 2-1/4" HIGH.
6D6 SIDELIGHT SILL
4 1/
4"
GLASS
STOPS
CASING
SILL
GLASS
1/4" COVER STRIP
STOPS
7D6 SIDELIGHT SILL
SILL/JAMB
SILL
1/4" COVER STRIP
8D6 SIDELIGHT SILL
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
TI DOORS &DOOR FRAMES
D6
TRIM ELEMENTS
DOOR TRIM3" = 1'-0"
3/8" = 1'-0"
3/8" = 1'-0"
3" = 1'-0"
DOOR + SIDELIGHT CONDITIONS3" = 1'-0"
DOOR TYPES & TRIM
FRAME TYPES
Hardware Set No. 5. each door to have:1 1/2 pair butts, 'Hager' 1279, 4 1/2" x 4 1/2"1 privacy lockset, 'Schlage' S40D, Jupiter.
1 drop seal, 'Pemko' #434 APKL.
Hardware Sets
Head & Jamb gasketing, 'Pemko' S88 Series, color: clear. (Verify/coord. with door stop dimension)
Hardware Set No. 6. each door to have:
1 door pull, tubular style, 6" C. to C.1 door push, 3 1/2" x 12".1 kickplate, 6" x door width less 2".1 drop seal, 'Pemko' #434 APKL.Head & Jamb gasketing, 'Pemko' S88 Series, color: clear. (Verify/coord. with door stop dimension)
Hardware Set No. 2. each door to have:
1 privacy lockset, 'Schlage' S40D, Jupiter.1 kickplate, 6" x door width less 2".
1 drop seal, 'Pemko' #434 APKL.
Head & Jamb gasketing, 'Pemko' S88 Series, color: clear. (Verify/coord. with door stop dimension)
WOOD CABINET DETAIL3" = 1'-0"
Doors & Frames NotesAll solid doors shall be 1 3/4" thick, solid core doors 1.
2. Door hardware finish shall be noted on finish schedule.
as scheduled and specified on this sheet.
3.
4. Refer to 8-1/2" x 11" Room Finish Schedule for finish specifications.Material selection includes:
-interior doors (species & finish)-wood trim (species & finish)-hardware finish-all cabinetry and coutertop selections-grommet colors-acoustical ceiling panel type-all wall and floor finish materials
5. Set glazing 'outboard' to allow blinds to be mounted within room.
6. Hollow metal frames shall be 16 GA all welded construction, noknock down frames allowed. All welds to be ground smooth, entireframe assembly to be factory primed and prepared to receive hardware.
7.
8. Maximize overall assembly and glass dimension, do not trim or cut casing.Coordinate all building elements, see plan for sidelight glass dimension (±).Field verify and coordinate all conditions.
All closers are to mounted on the specified side, see hardware set andschedule. Closers shall not be viewable from Waiting Room, typical.
Certain door types may be proprietary in their sourcing - refer to 'Door Types & Trim' legend below.
10.
Hardware Set No. 4. each door to have:1 1/2 pair butts, 'Hager' 1279, 4 1/2" x 4 1/2".
1 drop seal, 'Pemko' #434 APKL.
Head & Jamb gasketing, 'Pemko' S88 Series, color: clear. (Verify/coord. with door stop dimension)
Hardware Set No. 8. each door to have:1 1/2 pair butts, 'Hager' 1279, 4 1/2" x 4 1/2".1 lockset, 'Schlage' S70PD, Jupiter.
Hardware Set No. 10. each door to have:1 1/2 pair butts, 'Hager' 1279, 4 1/2" x 4 1/2".
Hardware Set No. 1. each door to have:
1 lockset, 'Schlage' S51PD, Jupiter.
1 kickplate, 6" x door width less 2"
1 floor stop, 'Ives' #436.
Hardware Set No. 3. each door to have:
1 floor stop, 'Ives' #436.
1 1/2 pair butts, 'Hager' 1279, 4 1/2" x 4 1/2".1 latchset, 'Schlage' S10D, Jupiter.
1 hinge pin, 'Ives' #701 latchset, 'Schlage' S10D, Jupiter.
Hardware Set No. 7. each door to have:1 1/2 pair butts, 'Hager' 1279, 4 1/2" x 4 1/2".
1 floor stop, 'Ives' #436.1 drop seal, 'Pemko' #434 APKL.
Head & Jamb gasketing, 'Pemko' S88 Series, color: clear. (Verify/coord. with door stop dimension)
1 lockset, 'Schlage' S51PD, Jupiter.
1 latchset, 'Schlage' S10D, Jupiter.
All door, window and sidelight glazing to be 1/4" tempered and setin place with clear silicone.
1 1/2 pair butts, 'Hager' BB1279, 4 1/2" x 4 1/2".1 closer, 'LCN' #1461H (pull-side mounted)
Hardware Set No. 9. each door to have:
2 sliding pulls, 'Ives' #227.1 edge pull, 'Ives' #230.Pocket door frame assembly 'Hager' #9678 series
1 1/2 pair butts, 'Hager' BB1279, 4 1/2" x 4 1/2".
1 closer, 'LCN' #1461H (pull-side mounted)
1 1/2 pair butts, 'Hager' BB1279, 4 1/2" x 4 1/2".1 closer, 'LCN' #1461H (pull-side mounted)
REMARKSHARDWARESETTYPE
DOOR
DOOR SCHEDULEFRAMETYPE
DOORNO.
DOOR
W H T
101A
* DOOR, FRAME, & HARDWARE AS SPECIFIEDBY BUILDING SHELL ARCHITECT.
- - - - - *-
PROPRIETARY SOURCING:
DOOR TYPES 1, 2, 3, 4, 6, AND INTERIOR WINDOWS ( ELEV. 1/D12 )
SHALL BE PROVIDED BY TRUSTILE DOORS & CABINETRY, INC.
CONTACT REPRESENTATIVE FOR UNTHANK DESIGN GROUP
PROJECTS, LISA WILSON:
Lisa Wilson Design
2664 Brightside Court
Cape Coral, FL 33991
Phone: 239-336-9975
Email: [email protected]
Accessibility NotesAll threshold elements and floor material transitions shall be limited to a height of 1.
2. Door hardware limited to lever-style (typ.)
1/2" (max.). Raised thresholds shall be beveled with a slope no greater than 1:2.
3. Specified door closers all fully adjustable; verify opening force of 5 lbf (max.)
DOOR TO HAVE 1 1/2" CLEAR UNDERCUT
9. Textured glass to be installed with "textured" side facing outward (Hall side),"smooth" side to face inward (Room side).
101D 1-3/4"1 A 13'-0" 7'-0"
101B - - - - - *-101C - - - - - *-
SET CLOSER TO LIMIT MAX DOOR SWING AT 120°103 - - - - - *-104 - - - - - *-108 1-3/4"5 E 93'-0" 7'-0" -109 1-3/4"5 E 92'-8" 7'-0" -110 1-3/4"5 D 113'-0" 7'-0" -
Hardware Set No.11. each door to have:1 1/2 pair butts, 'Hager' 1279, 4 1/2" x 4 1/2"1 privacy lockset, 'Schlage' S40D, Jupiter.
1 drop seal, 'Pemko' #434 APKL.
Head & Jamb gasketing, 'Pemko' S88 Series, color: clear. (Verify/coord. with door stop dimension)
1 hinge pin, 'Ives' #70
111 1-3/4"5 D 73'-0" 7'-0" -113 1-3/4"5 D 63'-0" 7'-0" -
1 floor stop, 'Ives' #436.
114 1-3/4"5 D 32'-0" 7'-0" -115 1-3/4"3 C 33'-0" 7'-0" -117 1-3/4"6 D 103'-0" 7'-0" -118 1-3/4"5 D 12(2) 2'-0" 7'-0"
Hardware Set No. 12. pair of doors to have:3 pair butts, 'Hager' 1279, 4 1/2" x 4 1/2".
2 adjustable ball catches 'Ives' #347.2 dummy trim, 'Schlage' Jupiter.
1 threshold stop, 'Pemko' #1842AS (or equal).
2 hinge pins, 'Ives' #70.
PAIR OF DOORS TO HAVE 1 1/2" CLEAR UNDERCUT120 1-3/4"2 B 133'-0" 7'-0" -
Hardware Set No. 13. each door to have:
1 latchset, 'Schlage' S10D, Jupiter.
1 kickplate, 6" x door width less 2"
1 1/2 pair butts, 'Hager' BB1279, 4 1/2" x 4 1/2".
1 closer, 'LCN' #1461H (pull-side mounted)
1 floor stop, 'Ives' #436.
122A 1-3/4"3 C 33'-0" 7'-0" -122B 1-3/4"3 C 33'-0" 7'-0" -123 1-3/4"5 D 82'-6" 7'-0"127 1-3/4"5 D 13'-0" 7'-0" -128 - - - - - *-129 1-3/4"5 D 43'-0" 7'-0" -
1 hinge pin, 'Ives' #70
130 - - - - - *-131A 1-3/4"5 D 143'-0" 7'-0"131B 1-3/4"5 " "3'-0" 7'-0" " "
Hardware Set No. 14. pair of doors to have:3 pair butts, 'Hager' 1279, 4 1/2" x 4 1/2".
2 self-latching flush bolts 'Ives' #356 at top & bottom of inactive leaf.
1 dummy trim, 'Schlage' Jupiter, at inactive leaf.
1 threshold stop, 'Pemko' #1842AS (or equal).
2 hinge pins, 'Ives' #70.
1 lockset, 'Schlage' S51PD, Jupiter at active leaf. Strike at inactive leaf.
ACTIVE LEAFINACTIVE LEAF
132 1-3/4"5 D 103'-0" 7'-0" -133 1-3/4"5 D 32'-6" 7'-0" -135 1-3/4"5 D 33'-0" 7'-0" -136 1-3/4"5 D 52'-0" 7'-0" -
1 hinge pin, 'Ives' #70
137 1-3/4"5 D 33'-0" 7'-0" -139 1-3/4"5 D 23'-0" 7'-0" -
1 floor stop, 'Ives' #436.
140 1-3/4"5 D 23'-0" 7'-0" -141 1-3/4"5 D 102'-0" 7'-0" -142 1-3/4"5 D 52'-0" 7'-0" -143 1-3/4"4 D 32'-0" 7'-0" -152 1-3/4"4 D 32'-0" 7'-0" -
Head & Jamb gasketing, 'Pemko' S88 Series, color: clear.(Verify/coord. with door stop dimension)
UTILITECH WALL SECTION2D7 1 1/2" = 1'-0"
TM
VACUUM LINE
(WITH FRAMING)BOARD. BRIDGE BETWEEN STUDS
SEE ALSO 'ROUGH-IN DIAGRAM'THIS SHEET.
CONDITIONS W/ DENTALEQUIP. SUPPLIER.)
RUN ALL DENTAL UTILITIES TOTHIS STUD SPACE CAVITY.
BACKING. (VERIFY ALLANCHOR TO PLYWOOD
DETAIL, THIS SHEET)(LAYOUT PER PLAN
ELEC. CONDUITS
2 LAYERS 5/8" GYP. BD.
(FOR X-RAY SHIELDING)THIS SIDE ONLY
2 x 4 WD. STUDS
2'-5
"
3'-1
0 1/
2"
BACK WALL OF CAB.)BOTTLE TOWARDSBY SUPPLIER. (LOCATECLOSED WATER SYSTEM
UTILITY 'UMBILICAL' TODENTAL DELIVERY CART.(BY DENT. EQUIP. SUPPLIER)
1'-1
0 3/
4"
PANEL W/ ARM (AS DRAWN)(VERIFY W/ OWNER )
COMPUTER ARM MOUNTINGPROVIDE 2X BLOCKING BEHIND
PANEL LOCATION. (SHIM FULL BTWN.
SPACE FOR COMPUTERMONITOR (BY OWNER).SIZED FOR 17/19" FLAT
5/8" GYP. BD.
NOTE:
FRA
MIN
G (
CLR
.)
1D7
JUNCTION BOX FORDENTAL X-RAY. (LOCATE W/
FOR HEADER/BLOCK'G NOTES, SEE
DENTAL EQUIP. SUPPLIER).TEMPLATE PROVIDED BY
SECTION
FRA
MIN
G (
CLR
.)
3'-1
0 1/
2"
UTILITECH WALL SECTION1 1/2" = 1'-0"
1D7
(RECESSED 3")TOE-KICK PANEL W/ P.LAM.
TM
SECURE J-BOX TO CABINET.4-PLEX ELEC. OUTLET
42
2
TO 5 1/2" DIM.PLATE AND SETTING BLOCK
WALL BASE PER
1/4" CLR. SHIM SPACE
1'-8
"1'
-10
3/4"
5/8" GYP. BD.
FRA
MIN
GFR
AM
ING
(C
LR.)
5/8" GYP. BD.
(FOR X-RAY SHIELDING)
AS SOLID BLOCKING FOR
STUDS BEYOND(LAYOUT PER PLANDETAIL, THIS SHEET)
DOUBLE 2x HEADER(S)
XRAY. (DEVELOP VERT.DIMENSION INDICATED).
THIS SIDE ONLY
112"
7'-6
"
2 LAYERS 5/8" GYP. BD.
TO F
LOO
R (
U.O
.N.)
5/8" GYP. BD. ON 2 X WOODBLOCK'G W/ CORNER BEAD
3'-10 3/4"
4'-0" FIN. GYP.3 1/2"
1'-0
1/2
"3/
4"
FRA
MIN
G
1'-3
3/4
"
1'-4
1/8
"
3'-3 3/4" FRAMING
1 1/2" = 1'-0"UTILITECH WALL PLAN
5/8" GWB
3 1/2"
4D7
4-PLEX ELEC. OUTLET
CABINETSECURE J-BOX TO
TM
FIXED SHELF
1'-7 1/2"
1"
1-1/2" DIA. ACCESS HOLE,
BD. THIS SIDE ONLY.(FOR X-RAY SHIELDING)
PROVIDE RADIUS CORNERBEAD AT (2) HALL-SIDE
2 x 4 WOOD STUDS (TYP.)
CORNERS. NOTE: RADIUS
42
2 4
3/4"
2 LAYERS OF 5/8" GYP. CABINET BOX & STUD.POST-DRILLED THROUGH
1D7
2D7
VACUUM LINEFRAMING
FRAMING
4
FOR CABLESCLEAR DIM.
2
COMP. AIR
2
4
FIN
. GY
P.
1'-6
"
SEE SHT. D6WOOD TRIM
(TO POWER DENTAL UNIT).
SURFACE MTD. DUPLEXELEC. OUTLET ON STUDFACING INWARD.
1D7
2D7
RECOMMEND PLACEMENT TO
3D7 UTILITECH WALL ELEVATION
1 1/2" = 1'-0"
TM
SHT. D6CSEE
(PHONE SYSTEM N.I.C.)
PORT. VERIFY W/ SUPPLIER.
SEE ALSO SHT. D6CASING/TRIM AT TOP & SIDES
DIGITAL RADIOGRAPHY COMPUTERSUGGESTED LOCATION FOR
HAVE CORD HANG CENTERED.
4D7
VERIFY #, LOCATION & REQ'T W/J-BOXES FOR X-RAY & CONTROLLER.
DENTAL EQUIP. SUPPLIER.
HEIGHT OF SOFFIT. (TYP. EA. SIDE)
W/ DENTAL EQUIPMENT (X-RAY)
TELEPHONE WALL UNIT ORSUGGESTED LOCATION FOR
COORDINATE TELEPHONE LOCATIONCOMM. SYSTEM (VERIFY)
CSHT. D6SEE
COMPRESSED AIR LINE
GYP. BD.
PROVIDE 'CLEAN' TERMINATIONOF WALL COVERING TO MATCH
BELOW FLOOR IF BASEMENT
DENTAL X-RAY. (NOTE: DIRECTION ANDSUGGESTED LOCATION FOR
ELECTRICAL CONDUIT FOR X-RAY.
OR CRAWL SPACE AVAILABLE.
(SHOWN DASHED)'TOWER' C.P.U. (BY OWNER)
CONTRACTOR HAS OPTION TO
FROM ABOVE CEILING ORRUN THESE UTILITY LINES
NOTE:
2'-5
"
ROUGH-IN DIAGRAM1 1/2" = 1'-0"
(DRAWING ORIENTATION MATCHES 3/D7 - ABOVE)
42
5D7
42
ONLY VACUUM DELIVERS FROM BELOW.
STUD FRAMING;SEE PLAN DETAIL,
4-PLEX ELEC. OUTLETSECURE J-BOX TO
4-PLEX ELEC. OUTLETSECURE J-BOX TO
CABINET BOX & STUD.POST DRILLED THROUGH1-1/2" DIA. ACCESS HOLE,
CABINET.
THIS SHEET.
CABINET.
1'-6
"
LOCATION FOR DENTALCART UMBILICAL. (FOR REFERENCE)SURFACE MTD. DUPLEX
(FOR DENTAL UNIT POWER)FACING INWARD.ELEC. OUTLET. ON STUD
DUPLEX ELEC. OUTLET
SEE ELEVATION FOR DIMENSIONS.FOR DENTAL UMBILICAL.
LOCATION OF CUT-OUT
RUN THESE UTILITY LINES
(WITH FRAMING)BETWEEN STUDS.
FROM ABOVE CEILING.
IF NO BSMT. OR CRAWL SPACE,
ALL OTHER UTILITIES DELIVER
BELOW FLOOR IF BASEMENTOR CRAWL SPACE AVAILABLE.
3/4" PLYWOOD UTILITYTERMINATION BOARD. BRIDGE
FROM ABOVE CEILING OR
CONTRACTOR HAS OPTION TONOTE:
2 4
42
1'-6
"
VARY FROM ILLUSTRATION - VERIFY)MOUNTING/CONTROLLER DETAILS MAY
1'-3
"
1'-1
1 1/
4"1'
-7 1
/4"
4-PLEX ELEC. OUTLET
3'-6
"
DUPLEX ELEC. OUTLET
OUTLET. ON STUD - FACINGINWARD. (FOR DENTAL UNIT POWER)
SURFACE MTD. DUPLEX ELEC.
'PARKING PLACE' FOR MINI
(BY OWNER)WIRELESS KEYBOARD.
CABINET BOX AND BLOCKING).
SUPPLIER.UMBILICAL BY DENTAL EQUIPMENT
NOTE:ALL 'SOFT' TUBING CONNECTIONS(OF DENTAL UTILITIES) ANDMOUNTING (& DETAIL) OF DENTAL UNIT
3/4" PLYWD UTILITY TERMINATION
NOTE:ALL DENTAL UTILITIES TOBE PIPED TO 'HATCHED' AREAS.(AREAS ACCESSIBLE AT (2)LIFT OUT PANEL SECTIONS -REAR & FLOOR, ONE SIDEOF CAB. - VERIFY W/ ELEVATION.)
1'-3
"
LINE OF WOOD TRIM(BEYOND).
LINE OF WOOD TRIM(BEYOND).
COMPRESSED AIR LINE
2'-0
"
W/ UTILITY AREA).(CONNECTS SHELF AREA
MAGNETIC CATCHES FORREMOVABLE PANEL.(ALL 4 CORNERS)
(IN CABINET'S REMOVABLE PANEL)
LOCATION OF REMOVABLE ACCESSDASHED LINE INDICATES
PANEL IN CABINETRY.
3D7
REQUIRED, SEE SHEET D5.PROVIDE DATA CONNECTION AS
STRUCTURALLY CONNECTED BASEFRAMING. (SEE DETAIL 4/D7)
(TO SUPPORT LOADS OF DENTALX-RAY UNIT)
ALL FOUR CORNERS,TYP.TIED TO BUILDING STRUCTURE ABOVE,DEVELOP RIGID STRUCTURAL FRAME
CLOSED WATER SYSTEM BY SUPPLIER. (LOCATEBOTTLE TOWARDS BACK WALL OF CAB.)
UTILITY UMBILICAL (BY DENT. EQUIP. SUPP.)
SURFACE MTD. DUPLEX ELEC. OUTLET ONSTUD FACING INWARD, SEE 5/D7 (TO POWERDENTAL UNIT).
4 4
2 2
4 4
2 2
6D7
4"
FOR MOUNTING DETAIL).SEE DETAIL #6 BELOW(FAN BY COMPUTER SUPPLIER -
FOR COOLING FAN - VERIFYFREE AIR FLOW ABOVE CABINET.
PROVIDE 3-1/2" DIA. 'AIR HOLE'
6D7
EMPTY 3" DIA. PVC CONDUIT FOR TUBING.PLUMBING PVC, NO ELECTRICAL WIRING (SEESHT. D2). FINISH FLUSH W/ FLOOR.
EMPTY 3" DIA. PVC CONDUITFOR TUBING. PLUMBINGPVC, NO ELECTRICALWIRING (SEE SHT. D2).FINISH FLUSH W/ FLOOR.
EMPTY 3" DIA. PVC CONDUITFOR TUBING. PLUMBINGPVC, NO ELECTRICALWIRING (SEE SHT. D2).FINISH FLUSH W/ FLOOR.
EMPTY 3" DIA. PVC CONDUITFOR TUBING. PLUMBINGPVC, NO ELECTRICALWIRING (SEE SHT. D2). VERIFY SOLID 2X BEHIND
COMPUTER ARM MOUNTINGLOCATION (PROVIDE SHIMSTO PREVENT DEFLECTION OFCAB. SIDE W/ LAG MOUNTINGOF ARM).
DUPLEX ELEC. OUTLET
SUGGESTED LOCATION FORVOLUME CONTROL (VERIFY)
4-PLEX ELEC. OUTLET
MOUNT FAN AT 3-1/2" DIA. 'AIR HOLE'.VERIFY FREE AIR FLOW ABOVECABINET. (FAN BY COMPUTERSUPPLIER - SEE DETAIL #6 BELOWFOR MOUNTING DETAIL).
VERIFY FREE AIR FLOW IN FRAMING SPACEBETWEEN CABINETS FOR VENTING.
COMPUTER MONITOR & ARM (O.S.C.I.)DUPLEX ELEC. OUTLET
4-PLEX ELEC. OUTLET, SECURE TOCAB. BOX (SEE DWG. 1 THIS SHEET)
2 1/
2"
4-PLEX ELEC. OUTLET, SECURE TO CAB.BOX (SEE DWG. 1 THIS SHEET)
FRA
MIN
G
4-PLEX ELEC. OUTLETSECURE J-BOX TO CABINET.
NOTE; DATA-I.T. PORTS LOCATED INUPPER CABINET.
DENTAL VACUUM LINE (SEE DETAILS PROVIDED BYDENTAL EQUIPMENT SUPPLIER) NOTE: VACUUMALWAYS DELIVERS FROM BELOW FLOOR.
VACUUM LINE
(SEE GEN. NOTE #6 THIS SHEET) GYP. BD.
EQ.
3"
4"
8 1/
2"(3) ADJ. INVERTED 'TRAYS' OF 3/4" PART.
8 1/
2"SURFACES.
3'-9
1/2
"
2'-4
3/4
"
ACCESS DOOR PROVIDED WITHMAGNETIC CATCHES AT
6"
1'-8
"
6 1/
2"
3"
1 1/
2"6"
CA
B C
LR.
3/4" 1'-7 1/2" CLR. CAB.1'-5 1/2" CLR. CAB.
INVERTED PULL-OUT TRAY(S)
(THIS SIDE ONLY)
UMBILICAL CUT-OUT ATTOP AS ILLUSTRATED.
PULL AT BOTTOM AND DENTALCORNERS. PROVIDE FINGER
3/4" X 3/4" CONT. CLEAT.
REAR FIXED RAIL PIECE).(LOOSE IN DADO-HOLE IN
(THIS SIDE ONLY)AT BOTTOM OF CABINETREMOVABLE PANEL
(2) 'POSITIONING' WD. DOWELS.
(3) ADJ. INVERTED 'TRAYS' OF 3/4" PART.BD. & 3/4" X 1-1/2" FRAME. COVERW/ PLAST. LAM. (SLIDE OUTMOUNT W/ DRAWER GLIDES.)HOLD TRAYS 1" CLEAR OFBACK OF CABINET WHEN CLOSED.
3"
6 1/
2"7-PLY PLYWD. SIDE PANEL ONLY(FOR ADDED STRENGTH INMOUNTING OF COMPUTER ARM).
NOTE:
TO FLUSH).
PORTION OF CENTRAL VERT. PANELBELOW TO BE REMOVED, TO ALLOW
(RECESS STRIKE IN SHELF-
PROVIDE (2) 2 KGSCREW IN MAG. CATCHES.
ACCESS TO 3" PVC FROM SIDE.
CUSTOM-BUILTUTILITECH WALL CABINET W/PLAST. LAM. ON ALLEXPOSED SURFACES.
BD. & 3/4" X 1-1/2" FRAME. COVER
BACK OF CABINET WHEN CLOSED.HOLD UPPER TRAY 1" CLEAR OFMOUNT W/ DRAWER GLIDES.)W/ PLAST. LAM. (SLIDE OUT
6"
1'-8
"
6 1/
2"6"1 1/
2"
EQ.
1'-6
"
8 1/
2"
ALL EXPOSED
CUSTOM 'UTILITECH' CABINETW/ PLAST. LAM. ON
8 1/
2"
BEYOND.3/4" PART. BD. SIDE
CA
B C
LR.
(3 TOTAL); TOWARDS REAR.
PROVIDE 2" DIA. 'AIR HOLES'@ BOTTOM; EA. END & CENTER
3/4" LIFT-OUT PART. BD.
SURFACES. 3/4" PART. BOARDCONSTRUCTION. (U.O.N.)
CUSTOM 'UTILITECH' CABINETW/ PLAST. LAM. ON ALL EXPOSED
MARRING CABINET FINISH.TO ALLOW ADJUSTMENT WITHOUTTO BE SCREWED AT HOLE LOCATIONSINVERTED 'TRAYS'. DRAWER GLIDES PRE-DRILL (1 1/4" O.C.) AS FOR ADJUSTABLE
8D7
1"CLR.
2" DIA. HOLES IN CAB. TOPFOR AIR CIRCULATION. 2 EA. SIDE(4) TOTAL; TOWARDS REAR.
3/4" PART. BD. BACK
1'-4
"3/
4"
LEADING 3/4" EDGE OF CABINET BOXES TO BE FINISHED W/ 3 MIL. PVCSEE ROOM FINISH SCHEDULE FOR COLOR SELECTION.
11.
BAND (TYP.)3 MIL. PVC EDGE-
REMOVABLE PANEL TO BE 1"SHORT OF FULL HEIGHT OF RECESS.
3/4" FIXED VERT. DIVIDER
CASING/TRIM AT TOP & SIDESSEE ALSO SHT. D6
8 1/
2"
7D7 8
1/2"
1"
2 1/
2"
NO EXPOSED PULLS; (PROVIDE
RECESSED UPPER CAB. W/PLAST. LAM.; NO SHELVES;
SEE SHT. D6 FOR TRIM).SPRING MAGNETIC CATCHES -
ALL CABINETRY SHALL BE COVERED WITH PLASTIC LAMINATE (SEE ROOM FINISH SCHEDULE). 10.
RECESSED FINGER PULL.
OF CABINET.
TOE-KICK PANEL W/ P.LAM.(RECESSED 3")
REMOVABLE BOTTOMPANEL, THIS SIDE
3/4" LIFT-OUT PART. BD. ACCESS DOOR PROVIDEDWITH MAGNETIC CATCHES AT ALL CORNERS.PROVIDE FINGER PULL AT BOTTOM AND DENTALUMBILICAL CUT-OUT AT TOP AS ILLUSTRATED.
CUT-OUT FOR DENTAL UMBILICAL;
PL. LAM. OR PVC BAND.MAKE SMOOTH AND EDGE W/
3/4" PLYWD. FIXED SHELFW/ PLAST. LAM. ON ALL SURFACES.
3/4" (7-PLY) PLYWD. THIS SIDE PANEL ONLY.
PROVIDE 2" DIA. 'AIR HOLES'@ BOTTOM; EA. END & CENTER(3) TOTAL; TOWARDS REAR
3"
2" DIA. HOLES IN CAB. TOP FOR AIR CIRCULATION.2 EA. SIDE (4) TOTAL; TOWARDS REAR.
1-1/2" DIA. ACCESS HOLES, POSTDRILLED THROUGH CAB. BOX & STUD.
NOTE: COORDINATE OPERATION OF X-RAY W/DENT. EQUIP. SUPP. G.C. TO PROVIDE 3/4"PART. BD. (COVER W/ WALL COVERING TOMATCH) 'STAND-OFF' TO MATCH MOUNTINGPLATE/BOX; IF REQ'D FOR FREE OPERATION.
STRAPS AS SHOWN.PROVIDE (2) RESTRAINING
1'-1
1 1/
4"1'
-7 1
/4"
3"
10 1/4"
ERGOTRON MOUNT
SEE SHT. D6WOOD TRIM
SEE SHT. D6WOOD TRIM
7. REVIEW AND VERIFY ALL UTILITY REQUIREMENTS & CONDITIONS SHOWN HERE W/ DENTAL EQUIPMENT
CONT. 1/4" SHIM SPACE ASSUMED AROUND CABINET INSERTS. (TYP.)
SUPPLIER PRIOR TO CONSTRUCTION.
8.
LOCATIONS MUST BEGIN W/ FULL-SIZE TEMPLATE OF XRAY UNIT. (COORD. W/ OWNER - DENTAL EQUIP. SUPPLIER)LOCATION OF COMPONENTS IN CENTER GYP. BOARD PANEL (INCLUDING J-BOX
9.
6.
ALL TRIM, CASING & BASE SHALL BE AS SPECIFIED, SEE SHT. D6 & ROOM FINISH SCHEDULE.
GENERAL NOTES:
3.
2.
1.
4.
5.& INSTALLATION AND FINISH OF ALL WOOD TRIMS TO COMPLETE ASSEMBLY.
( not used )
GENERAL CONTRACTOR SHALL BE RESPONSIBLE FOR ALL CABINET/COUNTERTOP INSTALLATION
RECESSED UPPER CAB.W/ PLAST. LAM. ON ALLEXPOSED SURFACES.
34" PART. BD. DOOR W/PLAST. LAM.
2 EQUAL
3/4" PLYWOOD UTILITY TERMINATION BOARD.BRIDGE BETWEEN STUDS. (WITH FRAMING)
CUSTOM 'UTILITECH' CABINETW/ PLAST. LAM. ON ALLEXPOSED SURFACES
SECURE J-BOX TO CAB.
SECURE J-BOX TO CAB.
SECURE J-BOX TO CAB.
SECURE J-BOX TO CAB. SECURE J-BOX TO CAB.
SECURE J-BOX TO CAB.
GENERAL CONTRACTOR TO VERIFY & PROVIDE ANY REQUIRED RATING FOR WOOD FRAMING12.
10 1
/4"FRAME HORIZONTAL
LINTEL - W/ KING STUDBLOCKING AS STRUCT.
AND JACK STUDS.(TYP. EA. SIDE)
(SEE FRAMING NOTE @ 4/D7)
PENETRATION OF SCREWS INTO
(MOUNTING NOTE; MUST VERIFY LAG
DBL. 2X BLOCKING BEHIND GYP. BD.)
FRAMING NOTE:
CORNER BEAD CONT.TO FLOOR. RADIUS WALL BASE TO MATCH. SEE ROOM FINISH SCHED.
AREA BELOW DRAWERSOPEN TO TOE-KICK BELOW(NO BOTTOM PANEL)
SCREW LENGTH PROVIDES FOR FULL
ARM (O.S.C.I.)ERGOTRON LX "WALL-MOUNT"
FINISH SCHEDULE
WALL BASE PERFINISH SCHEDULE
STAGGER SEAMS AS SHOWN.
( not used )
( not used )
( not used )
'DRAW' OF FRESH AIR COMES
6D7
AND TOP OF LOWER CABINET
FROM HOLES IN CAB. BOTTOM.VERIFY AIR HOLES IN THIS CABINET
NOTE: ISOMETRIC VIEW OF UPPER
(DOORS REMOVED FOR CLARITY)UTILITECH WALL CABINET.
BELOW.
COOLING FAN DETAILNO SCALE
BRACKET DISCARDED.(NOT SUPPLIED WITH FAN). NOTE; 'STAND-UP'WITH DRYWALL SCREWS & RUBBER WASHERS
AT CORNERS OPPOSITE THE FAN SPEEDDIAL. FAN MOUNTED TO CABINET TOP
REMOVE CAGE MOUNTING BOLTS
IN-CABINET ACCESS TO DIAL).TO MOUNT FOR REVERSED AIR FLOW ANDUNIT, AND 'FLIP' CAGES AND FAN SPEED DIAL-
OF CABINET WITH UPWARD AIRFLOW.(REMOVE CAGE MOUNTING BOLTS ON FAN
NOTE: FAN MOUNTED TO DRAW AIR OUT
PORT ON COMPUTER. (CORDSUPPLIED WITH FAN).
EXTENDING CORD TO 'USB'
FAN MOUNTED TIGHT TO HOLEIN CABINET BOX.
3-1/2" HOLE @ TOP OF CABINET.
(FAN BY COMPUTER SUPPLIER)NOTES @ RIGHT.FAN AS INDICATED INCOOLING FAN. CONFIGURE
'MOBILEFAN II'COMPUTER 'USB' POWERED
'THERMALTAKE'
ACCURIDE SLIDESELF CLOSINGWHITE ENAMEL#3832-C145SC (EW)
DETAIL8D7 FULL SCALE
ACCURIDE SLIDESELF CLOSINGWHITE ENAMEL#3832-C145SC (EW)
FULL SCALE
7D7 DETAIL
8D7
UTILITECH WALL
D7
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
1 1/2" = 1'-0"
1D8 WALL CABINET TRAY STORAGE2
D8 1 1/2" = 1'-0"
3D8 HALL COUNTER
2'-6
"
COUNTERTOPS.2-1/2" CABLING HOLE (TYP.)
SEE PLAN
1"
1"
SE
E E
LV.
TO UNDERSIDE OF APPLY BACKING SHEET
1 1/
2"
BUSINESS COUNTER6D8 1 1/2" = 1'-0"
3'-0
"
TYPICAL.EASE CORNERS / EDGES
PROVIDE 3/8" REVEALTYPICAL.
WOODAPRON
6"
SEE PLAN
1 1/2" = 1'-0"
3'-0
"
TYP. BASE CABINET
3/4" PART. BD. BOT. (TYP.)
RIM. FULL EXTENSION GLIDES.PLYWOOD BOTTOM W/ 3/4" X 1 1/2"
PLASTIC LAMINATE OR WOOD TO MATCH EXTERIOR COVERED 3/4"
4D8 1 1/2" = 1'-0"
BASE BLOCK'G.
SEE ELEVATIONS.
SLIDING TRAY:
3"
1/4" HARDBD. BACK (TYP.)
SEE PLAN
SE
E E
LV.
1 x 4 WD. BLOCK'G
LAM. (TYP.) (POST-FORMED)
3/4" PART. BD. COUNTERTOP& BACKSPLASH W/ PLAST.
1 1/
2"
3/4" PART. BD. DOOR
DRAWER, 1/4" HARDBD.BOT. & 3/4" PART. BD.DRAWER FRONT.
1 X 4 WD. INTERMED. RAIL
1/2" WOOD SIDES ON
SEE INTERIOR ELEVATIONSFOR VERT. DIMENSION.
1 1/2"
NOTE:
POST-FORMED PLASTIC LAM.FULL BULLNOSE (OR WOODEDGE) SEE FINISH SCHEDULE.
LAM. (TYP.) (POST-FORMED)
3/4" PART. BD. COUNTERTOP& BACKSPLASH W/ PLAST.
SEE PLAN
TYP. DRAWER STACK1 1/2" = 1'-0"
5D8
SE
E E
LV.
3'-0
"
3"
SEE INTERIORNOTE:
OF DRAWERS
ELEVATIONS FORVERT. DIMENSIONS
1 1/
2"
@ SECT.SEE TYP. NOTES1 1/2"
4D8
POST-FORMED PLASTIC LAM.FULL BULLNOSE (OR WOODEDGE) SEE FINISH SCHEDULE.
SEE INTERIOR ELEVATIONSFOR VERT. DIM. OF TOESPACE.MATERIAL TO MATCH CABINET.
& 3/4" PLYWD. COUNTERTOPW/ WOOD SQUARE EDGE.
(SEE FIN. SCHED. FOR MATERIALS)(1/8" RADIUS TOP EDGE)
3/4" PART. BD. BACKSPLASH
VA
RIE
S -
SE
E E
LEV
.
VA
RIE
S -
SE
E E
LEV
.
SEE PLAN SEE PLAN
3/4" PART. BD. BOT.W/ PART. BD EDGE
1 1/
2"3/
4"
ALL SHELVES ARE TO
PREVENT "TIPPING"
WOOD DOOR RAIL &3/4" PART. BD. OR HARD-
STILE CABINET DOOR
BE REMOVABLE
NOTES:1.
LOCATE SHELF STANDARDS TO
2.
OF SHELF UPONTRAY REMOVAL.
3 1/
2"
3/4" PART. BD. DOOR
1/4" HARDBOARD BACK
3/4" PART. BD. ADJUST.SHELF (TYP.)
4D9
1 x 4 WD. BLOCK'G
3/4" PART. BD. TOP
LINE OF GYP. BD. VALANCEWHERE APPLICABLE
3/4"
1"
3/4" PART. BD. ADJUST.
1/8" GREY-LITE #31 TINTED
6'-4
"
SHELF (TYP.)
GLASS PANEL
3 1/
2"
1"
A.F
.F. PERFORATED STEEL SHELVES
16 GAUGE, POWDER COATED,
W/ ROLLED FRONT EDGES.
CONTINUOUS LED UNDER-CABINETLIGHT FIXTURE. NOTCH CABINETDIVIDER AS REQ'D. INSTALL PERMANUFACTURER'S RECOMMENDATIONS.HOLD ALL WIRING TIGHT TO BOTTOM OFCABINET. SEE SHT. D4.
(30mm) ENGINEERED QUARTZCOUNTERTOP W/ SQUARE FRONT EDGE.
COUNTERTOPS SHIPPED UN-PREPPED; GC TO BE RESPONSIBLECABINETS, COUNTERTOPS, & VALANCES WILL BE OWNER-PROVIDED.NOTE TO CONTRACTOR: TREATMENT ROOM SIDE
FIXTURES, GROMMETS, ELEC., ETC.) SEE ALSO NOTES @ SHEET D7.FOR CAB. INSTALLATION & ALL OTHER TRADE ELEMENTS (I.E. PLUMBING
SE
E E
LEV
.
5 1/
2"
TRTMT. ROOM SIDE COUNTER
3"
1 1/2" = 1'-0"
7D8
6
2
6
2
SEE PLAN
SE
E E
LEV
.
SEE INTERIORELEVATIONS FORVERT. DIMENSIONSOF DRAWERS
SEE TYP. NOTES@ SECT.
NOTE:
4D8
LAM. FULL BULLNOSEPOST-FORMED PLASTIC
& BACKSPLASH W/3/4" PART. BD. COUNTERTOP
TYP. DRAWER CONST.
PLAST. LAM.
1 1/2" = 1'-0"TRTMT. ROOM SIDE COUNTERS8
D8
ONE ON OPP. SIDECABINET SIMILAR TO
SE
E E
LEV
.
SE
E E
LEV
.
6
23"
5 1/
2"2
6
PROVIDE CUT-OUTSAS REQ'D FOR
LINES.SINK & PLUMBING
5/8" GYP. BD. ON 2 X 4WOOD STUDS @ 16" O.C.
FLOOR PLAN.SINK-- SEE
SE
E E
LV.
SEE PLAN3/4"
POST-FORMED PLASTICLAM. INTEGRAL BACKSPLASH
MATCH COLOR TO WALL PAINT & LAMINATE.SEALANT AT WALL BACKSPLASH JOINT,
CUSTOM POST-FORMED
VT INDUSTRIES (VTI) OR EQUALGO TO (WWW.VTINDUSTRIES.COM) SELECT
NOTE:
'FINE LAMINATE COUNTERTOPS', THEN SELECTCUSTOMER SERVICE FOR REGIONAL LOCATIONS.
COUNTERTOP RESOURCE:
DO NOT EXCEED PLAN DIM.
1 1/2"
BULLNOSE
DOOR & DRAWER FRONTS.DIMENSION IS TO FACE OF
SHOWN ON SHEET D2.DO NOT EXCEED DIMENSION
DO NOT EXCEED PLAN DIM.3/4"
BULLNOSE
1 1/2"
BASE TO MATCH CABINET MATERIAL
LOCKERS1 1/2" = 1'-0"
17D8
1/4" HARDBD. BACK (TYP.)
3/4" PART. BD. DOOR
3/4" PART. BD. SHELVES (TYP.)
3/4" PART. BD. BOT. (TYP.)
PLAST. LAM. ALLSURFACES (TYP.)
2
LINE IND. CABINETSIDE BEYOND.
4"
LIGHT FIXTURE
CLG. GRID WALL ANGLES
AS SCHEDULED
(CUT LOUVER AS NEEDED)
4'-0" X 3 3/4" (+/-) LOUVERPIECE, LOOSE LAID IN VALANCE(PC1-S) BY LITHONIA LIGHTING
1"
7 1/
2"3/8"
3/8"
5" 1 1/2"
2"
3/4" WOOD VALANCE
PIECES REQUIRED BY INT. DESIGNER)(VERIFY ANY ADDITIONAL PROFILE
MOULDINGPROFILED WOOD
1 1/2" = 1'-0"
18D8 WALL CABINET
VA
RIE
S -
SE
E E
LEV
.
SEE PLAN
3/4" SHAKER STYLE
1 x 4 WD. BLOCK'G
3/4"
1"
SHAKER STYLE WOOD
QUARTER ROUNDINTERIOR EDGE
STILE & RAIL FRAME
3/4" PART. BD. BOTTOMW/ WOOD VENEER (TYP.)
1/4" PART. BD. BACK W/WOOD VENEER (TYP.)
3/4" PART. BD. ADJUST.SHELF W/ WOODVENEER (TYP.)
3/4" PART. BD. TOP W/WOOD VENEER (TYP.)
WOOD DOOR, SEE
PLASTIC LAMINATE
SEE TYP. NOTES@ SECT. #4
BASE TO MATCH CABINET MATERIAL
SINGLE DOOR WIDTH.NOTE: SHELVES ONLY SPAN
PROVIDE VERTICAL DIVIDERSAS NECESSARY.
(SEE ALSO DET. 10; SHEET D9)
PULLS AS SPECIFIED(SEE ROOM FINISHSCHEDULE)CABINET LOCK (TYP.)
PLAST. LAM. ALLSURFACES (TYP.)
DETAIL #3/D6.
WOOD OR METAL COUNTERSUPPORTS (CONTRACTOR'S OPTION).SEE FINISH SCHEDULE FOR COLOR.(4'-0" CTR. SPANS MAX.)
UNIQUE DRAWER DEPTHAT LAB LOCATION.
REFER TO ELEVATIONS FORNOTE:
BLOCKING2x WOOD
NOTE:SEE ALSO DETAILS 12AAND 12B ON SHEET D9
BASE BLOCK'G.
2
1" 1"
1 1/
2"
1 1/
2"3/
4"
1"
EXPOSED SIDE PANEL TO FINISH ALIGNEDW/ LOWER EDGE OF FACE OF CAB.
3'-0
"
WRAP DRAWER CAB.
3/4" PART. BD. BOT. (TYP.)
RIM. FULL EXTENSION GLIDES.PLYWOOD BOTTOM W/ 3/4" X 1 1/2"
PLASTIC LAMINATE OR WOOD TO MATCH EXTERIOR COVERED 3/4"
14D8 1 1/2" = 1'-0"
22 x WD. BLOCK'G.
SEE ELEVATIONS.
SLIDING TRAY:
23"
1/4" HARDBD. BACK (TYP.)
SEE PLAN
SE
E E
LV.
1 x 4 WD. BLOCK'G
LAM. (TYP.) (POST-FORMED)
3/4" PART. BD. COUNTERTOP& BACKSPLASH W/ PLAST.
1 1/
2"
3/4" PART. BD. DOOR
DRAWER, 1/2" WOODBOTTOM & 3/4" PART.BD. DRAWER FRONT.
1 X 4 WD. INTERMED. RAIL
1/2" WOOD SIDES ON
1 1/2"
POST-FORMED PL. LAM.FULL BULLNOSE (OR WD.EDGE) SEE FINISH SCHED.
SEE INTERIORELEVATIONS FORVERT. DIM. OFTOESPACE. MATERIALTO MATCH CABINET.
3"3"
LAM. (TYP.) (POST-FORMED)
3/4" PART. BD. COUNTERTOP& BACKSPLASH W/ PLAST.
SEE PLAN
PLASTER DRAWERS1 1/2" = 1'-0"
15D8
SE
E E
LV.
3'-0
"
3"
2 E
QU
AL
1 1/
2"
1 1/2"
POST-FORMED PLASTIC LAM.FULL BULLNOSE.
BASE BLOCK'G.
SEE FINISH SCHEDULE.
HEAVY-DUTY FULL EXTENSIONDRAWER GLIDES.
1 x 4 WD. BLOCK'G
1 X 4 WD. INTERMED. RAIL
SEE INTERIOR ELEVATIONSFOR VERT. DIM. OF TOESPACE.MATERIAL TO MATCH CABINET.
3/4" PART. BD. BOT. (TYP.)
1/4" HARDBD. BACK (TYP.)
HEAVY-DUTY DRAWER CONSTR:1. 1/2" MIN. SOLID WOODDRAWER BOTTOM.2. DRAWER BOX TO BE DOVETAILCONSTRUCTION/JOINING.3. DRAWER GLIDES TO BE RATEDFOR MIN. LOADS OF 150#.4. VERIFY MIN. INSIDE DRAWERCLEARANCES WITH OWNERSPLASTER BOX SIZE.
1/2" SOLID WOOD SIDES ONDRAWER, 1/2" MIN. SOLID WOODBOT. & 3/4" PART. BD. DRAWERFRONT. (SEE HEAVY-DUTYDRAWER CONSTRUCTION NOTES.)
(TO PREVENT COUNTERTOP SAG)
PROVIDE 3/4" PLYWD BASE LAYER ASSTIFFENER OVER WRAP DRAWER SPAN
FULLY ADHERE/GLUE PLYWD LAYERTO COUNTERTOP LAYER
BOTTOM OF EXPOSED SIDE PANELS TO ALIGNW/ BOTTOM EDGE OF CAB FACE FRAME.
1 1/2" = 1'-0"
13D8 STATIM CABINET
3'-0
"
4"(CLR.)
PROVIDE 1-3/4" X 12" VENT SLOT INTOE-SPACE. SEAL HOLE & PROVIDEDOUG MOCKETT #CP2 PAPER SLOTGROMMET, FIX IN PLACE WITH SILICONE.
2 x WD. BLOCK'G.
3/4" PART. BD. BOT. (TYP.)
1/4" HARDBD. BACK (TYP.)
PROVIDE POWER IN CAB.(VERIFY REQUIREMENTS)
SEE ELEVATIONS.EXTENSION GLIDES.
3/4" X 1 1/2" PLAST. LAM. RIM.
SLIDING TRAYS:16 GAGE STAINLESS STEEL W/
SEE INTERIOR ELEVATIONSFOR VERT. DIM. OF TOESPACE.MATERIAL TO MATCH CABINET.
23"
3/4" PART. BD. DOOR
CABINET PULLS; PLACEHORIZ. PULL AT CENTER OFSLIDING TRAY. (TRAY TOFLUSH W/ FACE OF DOORS).
SEE PLAN
SE
E E
LV.
FOR VERT. DIMENSIONS.SEE INTERIOR ELEVATIONS
POST-FORMED PLASTICLAM. FULL BULLNOSE
NOTE:
1 1/
2"
1 1/2"
INTERIOR OF CABINET TO BE FULLY LINEDWITH STAINLESS STEEL. ATTACH LINERSWITH STAINLESS SCREWS AND WATERRESISTANT WASHERS. SEAL ALL INSIDESEAMS WITH CLEAR SILICONE CEMENT.
AT TRAY FRONT & FULL
NOTES:DOOR AND DRAWER FRONTSCOVERED WITH PLASTIC LAMINATE.ALL INTERIOR SURFACES TO BESTAINLESS STEEL (INCLUDINGUNDERSIDE OF COUNTERTOP)
LOCATE 'EXTRACTOR' IN LOWERCABINET. (PRECISIONEQUIPMENT SERVICES, INC.(605) 347-0452 CONTACT:
LANCE MOON).
FOR VERT. DIMENSIONS.SEE INTERIOR ELEVATIONSNOTE:
'STATIM' UNIT (BY OTHERS).DENTAL EQUIP. SUPPLIER TOPROVIDE 'DRIP TRAY' UNDER UNITTO PREVENT MOISTURE RUN-OFF.
'STATIM' UNIT (BY OTHERS).DENTAL EQUIP. SUPPLIER TOPROVIDE 'DRIP TRAY' UNDER UNITTO PREVENT MOISTURE RUN-OFF.
CONTINUOUS LED UNDER-CABINETLIGHT FIXTURE. NOTCH CABINETDIVIDER AS REQ'D. INSTALL PERMANUFACTURER'S RECOMMENDATIONS.HOLD ALL WIRING TIGHT TO BOTTOM OFCABINET. SEE SHT. D4.
1'-1
"(V
ER
IFY
W/ O
WN
ER
)1'
-1"
(VE
RIF
Y W
/ OW
NE
R)
1 1/2" = 1'-0"
16D8 OPEN WALL CABINET
VA
RIE
S -
SE
E E
LEV
.
SEE PLAN
3/4" PART. BD. BOT.W/ PART. BD EDGE
2 1/
4"
1/4" HARDBOARD BACK
1 x 4 WD. BLOCK'G
3/4" PART. BD. TOP
1 1/
2"
CONTINUOUS LED UNDER-CABINETLIGHT FIXTURE. NOTCH CABINETDIVIDER AS REQ'D. INSTALL PERMANUFACTURER'SRECOMMENDATIONS. HOLD ALLWIRING TIGHT TO BOTTOM OFCABINET. SEE SHT. D4.
BOTTOM OF EXPOSED SIDE PANELS TO ALIGNW/ BOTTOM EDGE OF CAB FACE FRAME.
1"
1"
1 1/2" FACE FRAME (TYPICALAT TOP & SIDES.)
1 1/
2"3/
4"
LINE OF FACE FRAMEBEYOND.
1" MDF ADJUSTABLE SHELFWITH MATCHING PLAST.LAMINATE TOP AND BOTTOM.FRONT FACE WITH PLAST. LAM.OR PVC EDGING.
1"
HOLES TO ALLOW FOR 1-1/2" DRILL ADJUSTABLE STANDARD
CLEAR SPACE BETWEEN STEELSHELVES.
1 1/2" = 1'-0"
9D8
CONTROL COUNTER
ON INTERIOR ELEVATIONS.3/8"
8"
2'-6"
10 1/2"
1"
2'-2
"
WALL BASE AS SPECIFIED INROOM FINISH SCHEDULE
4"
1 1/
2"
3"
(REFER TO FINISH SCHEDULE)GLASS TILE ACCENT BAND
1X WOOD TOP-BAND1/2" WOOD QTR. RD.
3/4" PLYWD.2 LAYERS OF
AT 16" O.C.2 X 6 WD. OR MDF STUDS
1 1/2" 2"
1"
1 1/
4"
1'-1
"
APPLY PLAST. LAM. ONNOTES:
ALL EXPOSED SURFACES.
2 LAYERS OF 3/4" PLYWD.
1/2" PLYWD. CLOSURE
LED PUCK LIGHT
3/4" PLYWD. COUNTER-TOP W/ WOOD SQUARE EDGE(1/8" RADIUS TOP EDGE)
SEE SHEET D4.
TO UNDERSIDE OF COUNTERTOPS.
APPLY BACKING SHEET
2-1/2" CABLING HOLE (TYP.)
COUNTER SUPPORT (STAIN TO MATCH WD-1)
1'-0"
(30mm) ENGINEERED QUARTZ COUNTERTOPW/ EASED FRONT EDGE (1/8" RADIUS)
FIXED DIVIDERS AS SHOWNPROVIDE 1/2" PLYWD.
3/4" PLYWD. COUNTER W/1 X 1 WOOD EDGE
ADJUST SCRIBE AS NECESSARY
4"
WOOD SQUARE EDGE(1/8" RADIUS TOP EDGE).LAMINATE AS REQ'D ATCURVED SURFACES.
WOOD SQUARE EDGE.LAMINATE AS REQ'D ATCURVED SURFACES.
(OVER 1/2" PLYWD. SUBSTRATE)
SURFACE MOUNTED
1'-0
"1/2" PARTICLE BOARD, BACK- KERF AS REQ'D.
3/4" SUBSTRATE: FLEX-BOARDOR PARTICLE BOARD(CONTRACTORS OPTION).
TONGUE & GROOVE PANELINGAT FACE OF CABINET. (SEEDETAIL #9a/D8 & ELEVS.)
(W/ PLAST. LAM)
1"
3/4"
1"
3 1/
2"CONCEAL WIRING AND LED PUCK LIGHT TRANSFORMERWITHIN STUD SPACE. HOLD ANY EXPOSED PUCK LIGHTWIRING TIGHT TO VERT./HORIZ. SURFACES NEAR REAROF CABINET. CONCEAL WIRING TO GREATEST EXTENTPOSSIBLE.
VANITY COUNTER1 1/2" = 1'-0"
10D8
5"2'
-5"
2'-1
0"
9" M
IN.6" MAX.
3/4" WOOD PANEL, MAKE
SUPPORT W/ 2X
3-1/2" x 3" x 1/4"STL. ANGLE
CLEAT AT EA. END
2'-0"
UNDERMOUNT SINKSEE PLUMB. SCHED.
8" MIN.
2"
WALL FRAMING.
3-1/2" x 2" x 1/4"
(COUNTERSINK)
COUNTER & APRON. 3/4" PLYWD. SUPPORT
BOLT TO STL. ANGLES
CLEAT AT EA. ENDSUPPORT W/ 2X
LAG SCREW TO2X CLEAT (BEYOND)
STL. ANGLE
30mm ENG. QUARTZCOUNTERTOP (W/ EASEDSQ. EDGE) & APRON.
POLISH/SMOOTH EDGES ATSINK CUT-OUT LOCATION.
SE
E E
LV.
FULLY ADHERED MIRROR W/ RADIUSMACHINED EDGE. APPLY BEAD OFCLEAR SILICONE BETWEEN MIRROR& BACKSPLASH.
TILE WAINSCOT IS CONTINUOUSBEHIND MIRROR, TYP.
PROVIDE HARD BOARD STANDOFFBEHIND MIRROR FLUSH WITHFACE OF TILE. HOLD BOARDBACK 1/2" FROM ALL EDGES, TYP.
TILE WAINSCOT
TILE WAINSCOTBACKSPLASH
REMOVABLE (ATTACH
TO CONCEAL PIPING (SCRIBE TO SINK AS REQUIRED)
W/ CONT. VELCRO STRIPS),
ON SHT. D2
SINK STANDARDS/SUPPORTSINSTALLED PER SINK MFR.DIRECTIONS
8" MIN.
2"
2'-0"
2'-1
0"
5"
BACKING SHEET TO
9" M
IN.
VANITY COUNTER1 1/2" = 1'-0"
11D8
COUNTERTOP.UNDERSIDE OF
6" MAX.
SE
E E
LV.
PROVIDE PL. LAM.
BLOCKING1 X 4 WOOD
LAVATORY-- SEEFLOOR PLAN.
TILE WAINSCOT BACKSPLASH
2'-5
"
FOR COUNTERTOP MATERIALREFER TO FIN. SCHEDULE
MA
X. D
IM. T
O S
INK
RIM
FULLY ADHERED MIRROR W/ RADIUSMACHINED EDGE. APPLY BEAD OFCLEAR SILICONE BETWEEN MIRROR& BACKSPLASH.
TILE WAINSCOT IS CONTINUOUSBEHIND MIRROR, TYP.
TILE WAINSCOT
PROVIDE HARD BOARD STANDOFFBEHIND MIRROR FLUSH WITHFACE OF TILE. HOLD BOARDBACK 1/2" FROM ALL EDGES, TYP.
REMOVABLE PANEL (ATTACH
TO CONCEAL PIPINGCOVER W/ PL. LAM.ALL SURFACES (SCRIBE TOSINK AS REQUIRED)
W/ CONT. VELCRO STRIPS)
PROVIDE SEALER ON UNDERSIDE
SEE FLOOR PLAN
3"
VANITY CABINET
& PLUMBING LINES.
1 1/2" = 1'-0"
12D8
FLOOR PLAN.LAVATORY-- SEE
PROVIDE CUT-OUTS ASREQ'D. FOR LAVATORY
3/4" PART. BD. STOP
OF COUNTER EDGE. (TYP.)
SE
E E
LEV
ATI
ON
SE
E E
LEV
.4"
1 1/
2"S
EE
ELE
V.
SEE TYP. NOTES
4D8
@ SECT.
3/4"
CABINET MATERIALBASE TO MATCH
FULLY ADHERED MIRROR W/ RADIUSMACHINED EDGE. APPLY BEAD OFCLEAR SILICONE BETWEEN MIRROR& BACKSPLASH.
SE
E E
LV.
3/4" PART. BD. COUNTERTOPW/ PLAST. LAMINATE (TYP.)
REFER TO FINISH SCHEDULEFOR SPLASH MATERIAL
LINE OF GYP. BD. VALANCEWHERE APPLICABLE
9aD8
3"
3/4"
T&G PANELINGHALF SCALE
TI CABINETS
D8
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
NOTE:See "Cabinetry Notes"
on sheet D9
2"
WALL DTL.1D9 3/4" = 1'-0" 2'
-6" R
AD
.1"
SEE PLAN, SHEET D2. FOR CENTER POINT
BULKHEAD AND 1" OUT
OFFSET WALL END 1" INFROM FACE OF LIGHTING
LINE OF 1'-4" WIDE SOFFIT ABOVE
TOP OF WORK SURFACE(BELOW)
SEE PLAN, SHEET D2 FORCONTINUATION OF WALL
5/8" GYP. BD. ON ALLWALL SURFACES
TOP OF 1'-0" WIDE
LINE OF SOFFIT ABOVE
"UPPER" COUNTERTOP
2" (SHOWN DASHED)
(SOLID LINES)
(SHOWN DASHED)
1'-0
"
1"
FROM FACE OF UPPERCOUNTERTOP
3" 3 EQ.
TYP. AT 45° END OF SIDE CABINET(S).
WALL
DRAWERBASE
TREATMENT CAB. DTL.1-1/2" = 1'-0"
2D9
3/4"
3/4"
3/4"
ANGLED CORNER CABINETDOOR W/ PLAST. LAM.
PREVENT TIPPING.
TO ALLOW FREE ACTIONVERIFY CLEAR DIMS.
OF CAB. DOOR
SLIGHT RADIUS,
JOINT. (TYP OF 2)NO VERT. LAM.
W/ RETAINING CLIPS TO3/4" W/ PLAST. LAM.PROVIDE (2) ADJ. SHELVES;
NOTE: LEADING EDGE OFCOUNTERTOP OVERHANGSDOOR/DRAWER FRONTSBY 3/4" (TYP. - HOLD)
3" SEE ELEV.
TYP. AT 45° END OF SIDE CABINET(S).
WALL
3/4"
3/4"
3/4"
ANGLED CORNER CABINETDOOR W/ PLAST. LAM.
PREVENT TIPPING.
TO ALLOW FREE ACTIONVERIFY CLEAR DIMS.
OF CAB. DOOR
SLIGHT RADIUS,
JOINT. (TYP OF 2)NO VERT. LAM.
W/ RETAINING CLIPS TO3/4" W/ PLAST. LAM.PROVIDE (2) ADJ. SHELVES;
NOTE: LEADING EDGE OFCOUNTERTOP OVERHANGSDOOR/DRAWER FRONTSBY 3/4" (TYP. - HOLD)
7"
FAUCET
EQ
UA
L
3 1/4"
EQ
UA
L
6" 1'-1" (VERIFY W/ MFR.)
TRASH DROP
SINK
WALL WALL
TREATMENT CAB. DTL.1-1/2" = 1'-0"
14D9
2'-1
0"
BRADLEY MODEL
1'-6
"
NOTE:
1'-6
"
TOILET ROOM ACCESSORY MOUNTING
6"
1'-6"
17"-
19"
3D9 3/4" = 1'-0"
3'-0"
(TYP. ALL LOCATIONS)
IN PARTITIONS FORATTACHING GRAB BARS
PROVIDE 2 X WD. BLOCK'G
3'-0"
17"-
19" 2'-0
"
2'-1
0"
2'-1
0"
(AS SPECIFIED)TOILET
VE
RIF
Y
3'-6"
5" 5"
BRADLEY MODEL
S.S. GRAB BAR8120-001-42"
BRADLEY MODEL8120-001-36"
S.S. GRAB BAR
S.S. GRAB BAR
8120-001-18"
1'-0"
3'-3"
DIMENSIONS WITH LOCAL CODES.CONTRACTOR TO VERIFY ALL MOUNTING
NOTES:MEDICINE CABINET, TOILET TISSUE DISPENSER,
FOR LOCATIONS & SPECIFICATIONS.)AT HEIGHT ONLY (SEE PLAN SHEET D2
TOWEL & TRASH DISP.
NOTE:
BY CODES, VERIFY.
ELIMINATE VERTICAL GRAB BAR IF NOT REQ'D.
CONTRACTOR MAY
4'-0
" A.F
.F.
BO
TTO
M O
F M
ED
ICIN
E C
AB
INE
T
4'-0
" A.F
.F. M
AX
TO
DIS
PE
NS
ER
MEDICINE CABINET
& TOWEL & TRASH DISPENSER SHOWN
TOILET TISSUE DISP.
TILE WAINSCOT ACCESSORY TRANSITION:PORTIONS OF ACCESSORIES THAT FALL ON
HARDBOARD TO MATCH WALL.STANDOFF TO SHIM FLUSH WITH TILE, PAINTGYP. WALL (NOT TILE) TO HAVE HARDBOARD
7D9
8D9 NO SCALE
LAMINATE DETAILS
LAM. FULL BULLNOSEPOST-FORMED PLASTIC
COUNTERTOPS.
APPLY BACKING SHEET TO UNDERSIDE OF
BACKSPLASH W/ PLAST. LAM.3/4" PART. BD. COUNTERTOP &
1'-1
"
1/8" GREY-LITE #31 TINTEDGLASS PANEL
1/4" HARDBD. BACK
3/4" PART. BD. OR HARDWD.RAIL & STILE CABINET DOOR
3/4" PART BD. SIDES
1 1/2" = 1'-0"
4D9 TRAY STORAGE CAB. PLAN
MIN. INSIDE CLR. W/ DOOR OPEN
1'-4 1/2"
6"
TRASH DROP1 1/2" = 1'-0"
6"
6D9
TRASH MGMNT. GROMMETDOUG MOCKETT CO.
SEE SHT. D2 FOR SPEC.
LINE OF WALL
STERILIZATIONTRTMT. ROOMS
NO VERT. JOINTSLIGHT RADIUS
NO VERT. JOINTSLIGHT RADIUS
5D9 PLAN AT STERILIZATION TRASH DROPS
CAB. DIVIDER
1 1/2" = 1'-0"
HOLD CLOSE TOCAB. DIVIDER.
WALL6 1/2"
WALL 6"
TO MAKE 45 DEG. CORNER
WALL FACE.
(2) 22.5 DEG. MITRES
TERMINATE W/ VERT.
OUTSIDE CORNER. (SEEOTHER DWG. ABOVE)
45 DEG. CHAMFER AT
INT. 45 ° CORNERSTERILIZATION
SCRIBE TO MATCH
COUNTER & SPLASH
SCRIBE TO MATCH
(VERIFY W/ PLAN)
PLASTIC LAMINATE
POST-FORMED PROFILE
ACTUAL ORIENTATIONSMAY VARY FROM DETAIL,
POST-FORMED PROFILE
NOTE:
POST-FORMED
GROMMETS. SEE SHT.
DOUG MOCKETT CO.TRASH MANAGEMENT
@ SECT.SEE TYP. NOTES
TRASH DROP IN LAB1 1/2" = 1'-0"
2"
5"
1/2"
4"
CUSTOM FABRICATED'SQUARE' STAINLESS-STEELTRASH GROMMET 1/2"'SELF-RIM' W/ 2" DROP DIM.(SILICON IN PLACE)1/2"
6D9
PERFORATED STEEL SHELVES16 GAUGE, POWDER COATED,
W/ ROLLED FRONT EDGES.(PERFORATIONS 1" O.C.)
(SILICON IN PLACE)
D2 FOR SPECIFICATION.(SILICON IN PLACE)
7"
FAUCET
PLAN AT TRTMT. ROOM SIDE COUNTER SINK
EQ
.
3 1/4"
9D9 1 1/2" = 1'-0"
EQ
.
6" 1'-1"
TRASH DROP
SINK
WALL
SINGLE DOOR WIDTH.NOTE: SHELVES ONLY SPAN
PROVIDE VERTICAL DIVIDERSAS NECESSARY.
1/4"
1"
1"
1"
3/4" RECTANGULAR SIDE SPLASHES W/ PLAST.LAMINATE - MATCH HEIGHT OF POST-FORMEDREAR SPLASH (TYP.)
BUSINESS CTRS.
PROFILE VARIESWOOD EDGE
(ONLY)
W/ CTR. MATERIAL CHANGE.TERMINATE LOOSE SPLASH
(SEE FIN. SCHD.)
3/4" = 1'-0"
10D9 VALANCE LIGHT AT OPERATORY SIDE COUNTER
MOULDING
8D8
AS SCHEDULED
WALL4'-0" ±
3/4" WOOD VALANCELIGHT FIXTURE4'-0" X 4 3/4" (±) LOUVER
5 3/
4"
5'-6"
PIECE, LOOSE LAID IN VALANCE(LITHONIA # L GT8 PC1S)
CROWN
TO 3-1/2" @ TOP OF CABINET.
IN CABINET BOX.FAN MOUNTED TIGHT TO HOLE
EXTENDING CORD TO 'USB'
SUPPLIED WITH FAN).PORT ON COMPUTER. (CORD
NOTE: FAN MOUNTED TO DRAW AIR OUT
(REMOVE CAGE MOUNTING BOLTS ON FANOF CABINET WITH UPWARD AIRFLOW.
UNIT, AND 'FLIP' CAGES AND FAN SPEED DIAL-TO MOUNT FOR REVERSED AIR FLOW ANDIN-CABINET ACCESS TO DIAL).
REMOVE CAGE MOUNTING BOLTS
DIAL. FAN MOUNTED TO CABINET TOPAT CORNERS OPPOSITE THE FAN SPEED
WITH DRYWALL SCREWS & RUBBER WASHERS(NOT SUPPLIED WITH FAN). NOTE; 'STAND-UP'BRACKET DISCARDED.
'THERMALTAKE'
COMPUTER 'USB' POWERED'MOBILEFAN II'
COOLING FAN. CONFIGUREFAN AS INDICATED INNOTES @ RIGHT.(FAN BY COMPUTER SUPPLIER)
NOTE: ISOMETRIC VIEW OF LOWER
(COMPONENTS REMOVED FOR CLARITY)COMPUTER C.P.U. BASE CABINET.
INCREASE DRILLED HOLE SIZE
(NOTE: FRONT DOOR OMITTED FOR CLARITY)
(NOTE: COUNTERTOP OMITTED FOR CLARITY)
CLOSED CABINET SIDE OR
CUTAWAY. (FOR CLARITY)RETURN WALL CONSTRUCTION
OPERABLE REAR DOOR W/3" X 3" CUT-OUT FOR CABLEMANAGEMENT. (NO DOORWHERE FIXED BASE CABINETSABUT, PROVIDE 3" x 3" CUT OUT.)
NOT TO SCALE
11D9 VENTING IN BASE CAB. FOR CPU
'DRAW' OF FRESH AIR COMES FROMOPEN AREA @ TOE SPACE. PROVIDEOPEN CONDITION AS INDICATED.FINISH ALL EDGES W/ MATCHINGPLASTIC LAMINATE.
PROVIDE OPEN AREA AT TOESPACE OF ADJACENT CABINETS.FINISH ALL EDGES W/ MATCHINGPLASTIC LAMINATE.
FRAMING DETAIL OF DISPLAY COUNTER1 1/2" = 1'-0"
12BD9
2X FRAMING GLUED & SCREWEDTOGETHER TO FORM RIGIDSTRUCTURAL FRAME FOR QUARTZCOUNTERTOP & WOOD APRON.
FACE OF WOOD APRON &QUARTZ COUNTERTOP (SEESECTION #3, SHEET D8).
PLAN DETAIL AT DISPLAY COUNTER
2X FRAMING GLUED & SCREWEDTOGETHER TO FORM RIGIDSTRUCTURAL FRAME FOR QUARTZCOUNTERTOP & WOOD APRON.
WOOD APRON
12AD9 1 1/2" = 1'-0"
LAG SCREW TO FRAMING
WALL
LAG SCREW TO FRAMING
WALL
13D9
3 1/
4"
9 1/2"
11"
ULTRA-SONIC CONTROL1 1/2" = 1'-0"
EMPTY 2" PVC CORD CHASE
ALLOW ADEQUATE FREE 'PLAY' OFCORD CONNECTIONS-
CORD LENGTH FOR UNIT REMOVAL.
CLR
.
CLEAR AREA WITHIN WALL
FACE PLATE
CONTROL BOX
FRAMING - VARIES
ULTRA-SONIC CONTROLLERROUGH-IN BOX & FACE PLATE
PLAST. LAM. ALL EXPOSEDDOUBLE MDF FRAME W/
SURFACES. PROVIDED BY
TO CUSTOM PLAST. LAM. FRAME.SCREW ROUGH-IN BOX
FOR RECESSING CONTROLLER UNIT VERIFY ADEQUATE CLEARANCE
AND LOCATING 2" PVC CORD CHASE.COORDINATE W/ DENTAL EQUIP. SUPP.*
*
7"(M
IN. V
ER
IFY
)
X
GENERAL CONTRACTOR.
PROVIDED & INSTALLED BYDENTAL EQUIP. SUPP.
ROUGH IN BOX SIZE -VERIFY W/ DENTAL EQUIP. SUPPLIER.
2" PVC CORD CHASE
2x BRIDGING AS REQ'D,FOR MOUNTING OF PLAST. LAMINATE FRAME.
FACE PLATE
CUSTOM PLAST. LAM. FRAME
ELEVATION
PLAN
TI CABINETS
D9
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
Cabinetry Notes:1. The general contractor shall furnish and install wood blocking in metal stud partitions for the proper anchorage of all wall attached cabinets.2. Each trade shall be held responsible for knowledge of the general notes included throughout the contract documents and the applicable building codes.3. Apply plastic laminate or wood veneer on all exposed surfaces (no exposed particle board). See finish schedule for colors and finish materials. All colors and finish materials shall be approved by the Owner and Owner's agent. Provide 6" x 6" sample for all stained wood to Interior Designer for approval.
4. All Plastic Laminate cabinets to have 3mil PVC edge-banding at doors & drawer fronts. (Note; ‘Utilitech’ treatment room cabinetinsert (sheet D7), ONLY, also includes PVC edge-banding at all leading cabinet box and partition edges.) Contractor to verify closecolor-match of edge banding w/ surrounding plastic laminate selection. Bring any inconsistencies to the attention of the architectimmediately. See finish schedule.
5. All casework shall be manufactured and stored in accordance with the latest edition of the Architectural Woodwork Institute
Quality Standards. All cabinets shall be of standard full overlay construction, custom grade. Provide wood cabinets and
plastic laminate cabinets as shown, see interior elevations.
6. Countertops and splashes (and all exterior surfaces and insides of doors for the plastic laminate-faced cabinets) shall
receive plastic laminate in a standard matte finish, unless noted otherwise. Countertops in Treatment rooms, Sterilization,
and Lab shall be post-formed laminate w/ integral splash (see D8 & D9). Apply backing sheet to underside of countertops.
7. Provide 36 grommets (see 'wire management' type on sheet D2) place w/ owner.
All 'holes' within cabinets to be finished with grommet to match, fix in place w/ silicon.
8. Interior surfaces and shelves of all closed plastic laminate cabinets shall have vinyl finish melamine or equal.
(Exception; Plastic laminate doors shall have plastic laminate, vert. grade, inside & out.)
9. Interior surfaces and shelves of all wood cabinets shall have wood to match.
10. All cabinetry to be easily 'demountable' from wall without the use of special tools, procedures, or destructive means
(w/ removable fasteners/ screws).
11. Cabinet door hinges shall be "Blum" self-closing w/ 120° opening (or approved equal).
12. Drawer/tray glides shall be "Accuride" 3800 series, easy-close, full-extension (or approved equal).
13. See finish schedule for specification of cabinet pulls.
14. ( not used )
15. Line of gyp. bd. valance above cabinets is 1" back from face of cabinet (see sections & sheet D3).
16. Cabinet contractor to verify and coordinate all operational requirements and clearance dimensions of project cabinetry with walls
trim and by owner items (O.S.C.I.). This coordination includes but is not limited to the following:
A) Door and drawer operation is free and clear, allowing complete range of motion for all full extension glides and door swings.
B) Door and drawer operation shall not hinder appliance operation, i.e. dishwasher, refrigerator, washer, dryer, microwave, etc.
C) Cabinetry components, hardware, pulls, slides, etc. Coordinate and ensure complete free and clear operation of drawers and
doors. Provide a 1 1/2" scribe at the ends of all cabinet runs abutting adjacent wall assemblies to ensure adequate clearances.
17. Exposed particle board ends to be sealed completely with polyurethane, and allowed to dry, before completing
seaming and placing of countertop (Typ. all post-formed countertops).
ALL WALL CABINET INSTALLATION(SEE ALSO GEN. NOTE #'S 9 & 19; SHT. D1)
PROVIDE REQ'D BLOCKING FOR
ALL DRAWINGS ON THIS SHEETARE DRAWN AT 1/2" = 1'-0"
NOTES:
2'-1
0" M
AX
9D8
3'-6
"
5. REAPPT.
3'-6
"
2"2'
-6"
1'-0
"
6D8
OPEN TOWALL
4
OPEN TOWALL
51 2"5'
-6"
29
27
4. WAITING
15
18D8
2'-0
"2'
-0"
3'-0
"
4"
OPEN TOWALL
OPEN TOWALL
27
27
TI CABINETS
D10
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
Shaker-style wood cabinets. (w/ matching wood interiors.)
not used.
Engineered quartz countertop w/ eased sq. edge.
Adjustable shelf/shelves.
Finish end panel, to match, typical.
Shading indicates angle view.
Wall base.
Gyp. board bulkhead.
Gyp. board bulkhead w/ 2 layers of 14" gyp. bd. (@ curves)
Gyp. board valance (see cab. details for location of face.)
Plastic laminate backsplash.
Gyp. board.
KEYNOTES
15
5
19
2
1
14
13
31
32
29
30
27
28
'K & V' #770 coat rod & #734 flanges.24
Plastic laminate countertop w/ wood edge.4
Sliding tray w/ 3/4" wood bottom and 3/4" x 1-1/2"wood rims.
37
3 not used.
7 not used.
34
35 not used.
not used.8
not used.10
not used.6
9
not used.
33
Engineered quartz backsplash.12
not used.25
26 not used.
21
22
23
3/4" fixed wood shelf (see plan for depth) and 3/4" x 5-1/2"wood face. See also finish schedule.
11
Plastic laminate; this surface.16
End-support panel to floor.17
not used.18
not used.
not used.
38 not used.
39
40
not used.20
Chamfered corner panel from 2" stock.
not used.
not used.
Light fixture as specified on sheet D4.36
Wood or metal counter supports (contractor's option).See finish schedule for color. (4'-0" ctr. spans max.)
Open/clear under-cabinet area (for 15"W x 20"D mobilefile drawers by Owner)
not used.
Referenced this sheet
41 Refer to section on sheet D8 and to Room FinishSchedule for color/finish/materials at this location.
42 Glass shelf/shelves w/ radius machined edge. Provide (4)'Doug Mockett' SH7 shelf clamps (each shelf), positionedas shown. Color per room finish schedule.Verify shelf mounting heights w/ Owner.
ALL WALL CABINET INSTALLATION(SEE ALSO GEN. NOTE #'S 9 & 19; SHT. D1)
PROVIDE REQ'D BLOCKING FOR
ALL DRAWINGS ON THIS SHEETARE DRAWN AT 1/2" = 1'-0"
NOTES:
28
2
48
6
15
2
13
46
31
15
3'-0
"1'
-6"
2'-6
"
11 2"
8
21 4"
3'-0
"1'
-6"
2'-6
"
112"
1'-6" 1'-6"
1'-6"VERIFY
W/ OWNER
3813
27
3'-0
"1'
-6"
2'-6
"
27
3'-0
"1'
-6"
2'-6
"
112"
3'-0
"2'
-0"
2'-0
"
3'-0
"2'
-0"
2'-0
"
32
3'-0
"2'
-0"
2'-0
"
32
4"3'
-0"
OPEN TO WALL
OPEN TO WALL
4
54
32
55
57
4"
256
36
3232 32
32 32
5
1D81
D81
D8
9
9
32 32
27
TI CABINETS
D11
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
Shaker style wood cabinets. (w/ matching wood interiors.)
Plastic laminate faced cabinets. (w/ melamine interiors)
Engineered quartz countertop w/ eased square edge.
Adjustable shelf/shelves.
Finish end panel, to match, typical.
Shading indicates angle view.
Wall base.
Gyp. board bulkhead.
not used.
Gyp. board valance (see cab. details for location of face.)
Plastic laminate backsplash.
Gyp. board.
KEYNOTES
15
5
19
2
1
14
13
31
32
29
30
27
28
not used.24
Plastic laminate countertop w/ wood edge.4
Sliding tray w/ 3 4" plywd. bottom. 3 4"x112" hdwd. rim
Cover with plast. lam.37
3 Plastic laminate countertop w/ full bullnose.
7 not used.
34
35 Ventilate cabinets through toe-space for cpu.See detail #11 on sheet D9.
112" plastic laminate face frame.8
Open shelf cabinet w/ plastic laminate all faces.10
Post-formed plast. lam. countertop w/ full bullnose &integral backsplash.
6
9
Grey Lite #31 tinted glass (Typ.)48
not used.
33
not used.12
not used.25
26 not used.
21
22
23
not used.11
Plastic laminate; this surface.16
End-support panel to floor.17
not used.18
Provide empty 2" PVC data-chase in rear wall, penetratingall horiz. framing, to space above ceiling. 90 deg. turnoutthrough scribed hole in cabinet back.
38
Wood apron.20
not used.
not used.
ACCESSORY KEYNOTESBradley #987-36 recessed facial tissue dispenser.
Bradley Corp. (800.BRADLEY) www.bradleycorp.comDoug Mockett Co. (800.523.1269) www.mockett.com
ACCESSORY NOTES:
F
G
L
This icon designates points of important coordination withdental equipment supply company representative. Notesdescribing specific coordinating effort follow.
ICON
Pencil drawers, 6" short of full depth (to allow clearance).
'Wet' cabinet w/ full stainless steel liner & tray. Seecabinet details, sheet D8.
43
Top of cab: (2) 3" drawers w/ full extension glides (forpaper wraps by owner). Verify 24-12" clear width.
44
Provide spring-loaded magnetic catch on these (2) doorsonly. Hinges not self-closing @ this location.
45
See 'Laminate Details', sheet D9.46
Provide dental vacuum at 28" A.F.F. in base cabinet. Specialgrommet penetration at countertop for suction device. (Verifyall requirements w/ Dental Equipment Supplier.)
47
Heavy duty construction at these (2) drawers (for plasterstorage by owner). Rate drawer box & glides for loads of150#; min. (Verify plaster box size w/ owner)
39
Recessed 3 4" plywood backing (let into studs).40
Custom square trash drop; see detail #7, sheet D9.41
Doug Mockett #TM1B-SSS trash drop. (See details#5/D9, #6/D9 & #9/D9 for some specific placements.)
1" MDF adjustable shelf with matching plast. laminate topand bottom. Front face with plast. lam. or pvc edging.
Bradley #1985 recessed towel dispenser.
49 Statim cabinet: Locate 'Extractor' in lower cabinet.(Precision Equipment Services, Inc. (605)347-0452Contact: Lance Moon). Drain to plumbing waste.
Duplex elec. outlet for dent. equip. (Verify w/ equip. supplier).42
Fully adhered mirror w/ radius machined edges.36
50 Recessed Ultra-Sonic unit. Provided and installed byDental Equipment Supplier. Ultra-Sonic & grommetsto be set w/ silicone. Cut cabinet divider as required.
51 Ultra-sonic controller in plastic laminate frame, seedetail. Note; placement approximate, verify in fieldw/ Dental Equip. Supp. and available/adequateframing dimension.
52 Empty 2" PVC cord chase from base cabinet to wallframing space above, see detail.
Wood or metal counter supports (contractor's option).See finish schedule for color. (4'-0" ctr. spans max.)
53 1x4 stiffener board below countertop, running frontto back, for support between Ultra-sonic & sink.
Cut 312" hole through cab. divider and mount 'Thermaltake' fan
(by tech supplier) as shown. Hole should be located at thetop-rear corner of cabinet and cut edge finished with woodedge-banding at wood cabinet or 1mil PVC edge-banding atplastic laminate cabinet. Verify req's w/ tech supplier.
Referenced this sheet
54
55
56
Dashed lines indicate millwork & backsplash beyond wall.
Door not shown ( for clarity ).
Pencil drawer - hold 2" clear of rear wall to allow for cables.
57 See sheet D6 for trim/casing.
58 Terminate apron & countertop 14" short of finished gyp.board corners (Typ.)
59 Provide rigid structural frame. See detials #12A & 12Bon sheet D9.
60 Glass shelf/shelves w/ radius machined edge. Provide(3) 'Doug Mockett' SH7 shelf clamps (each shelf),positioned as shown. Color per room finish schedule.Verify shelf mounting heights w/ Owner.
61 Cabinet locks.
ALL WALL CABINET INSTALLATION(SEE ALSO GEN. NOTE #'S 9 & 19; SHT. D1)
PROVIDE REQ'D BLOCKING FOR
ALL DRAWINGS ON THIS SHEETARE DRAWN AT 1/2" = 1'-0"
NOTES:
2'-6
"2'
-0"
2'-6
"
14
27
28
1. WAITING
CASEDOPENING
2'-6
"2'
-0"
2'-6
"
10. TREATMENT ROOM 11. TREATMENT ROOM
37
12. R.R.
3'-0
"1'
-6"
2'-6
"
27
4
5
11 2"
52
52
53
53
54
54
27
13. C.A. 14. C.A.
112"
3'-8
"3'
-03 4"
11 2"
1324
58
8 8
TI CABINETS
D12
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
Shaker style wood cabinets. (w/ matching wood interiors.)
Plastic laminate faced cabinets. (w/ melamine interiors)
Engineered quartz countertop w/ eased square edge.
Adjustable shelf/shelves.
Finish end panel, to match, typical.
Shading indicates angle view.
Wall base.
Gyp. board bulkhead.
Gyp. board valance (see cab. details for location of face.)
Plastic laminate backsplash.
Gyp. board.
KEYNOTES
15
5
19
2
1
14
13
31
32
29
30
27
28
'K & V' #770 coat rod & #734 flanges.24
Plastic laminate countertop w/ wood edge.4
Sliding tray w/ 3 4" plywd. bottom. 3 4"x112" hdwd. rim
Cover with plast. lam.
37
3 Plastic laminate countertop w/ full bullnose.
7 Plastic laminate countertop & apron.
34
35
112" plastic laminate face frame.8
Open shelf cabinet w/ plastic laminate all faces.10
Post-formed plast. lam. countertop w/ full bullnose &integral backsplash.
6
9
33
12
Tile wainscot.25
26 Tile splash.
21
22
23
34" fixed shelf (see plan for depth) w/ plastic laminate
top & bottom, and 3 4" x 5-12" wood face.11
Plastic laminate; this surface.16
End-support panel to floor.17
Enclosed 4" high platform base.18
14" tempered safety glass.
38
See sheet D6 for trim/casing.
Engineered quartz apron.20
Light fixture as specified on sheet D4.
36
Wood or metal counter supports (contractor's option).See finish schedule for color. (4'-0" ctr. spans max.)
Referenced this sheet
Bradley grab bars. See #3/D9 for specification &mounting details.
ACCESSORY KEYNOTES
Bradley #155 recessed towel dispenser.
Bradley #987-36 recessed facial tissue dispenser.
Bradley Corp. (800.BRADLEY) www.bradleycorp.comDoug Mockett Co. (800.523.1269) www.mockett.com
Doug Mockett #TL-27 R-3" table leg. Center on peninsula.
ACCESSORY NOTES:
A
E
F
G
H
J
K
L
This icon designates points of important coordination withdental equipment supply company representative. Notesdescribing specific coordinating effort follow.
ICON
Doug Mockett #TM1B-SSS trash drop. (See details#5/D9, #6/D9 & #9/D9 for some specific placements.)
Bradley #1985 recessed towel dispenser.
Kohler #K-10555-BRZ coat hook at 5'-6" A.F.F. Provideblocking in wall behind gyp. bd. for coat hooks.
Kohler #K-10552-2BZ 30" towel bar at 2'-10" A.F.F.
Elec. outlet placement(s), verify w/ elec. drawings.
End of cabinet aligns with light valance above
Blocking in wall for towel bar (carries heavy lead apron).
Wall blocking for hook.39
Paper towel & facial tissue dispensers at opposite sideof wall - serving adjoining room. (Verify w/ plan).
Note; see 9/D9 for sink, faucet, & trash drop placement.40
41 Under-floor 3" PVC chase. Dimensions from F.O.'Utilitech' wall to center points of vert. PVC.
42 Double 2X framing as indicated - to provide requiredspacing.
43 Bradley 987-36 Recessed Facial Tissue Dispensers.(R.O. = 10-3 4" wide x 5-18" high x 4" deep). Allows 116"shim space around dispenser; shim at screw points asrequired.
44 Bradley 155 Recessed Paper Towel Dispenser. (R.O. =15-5 8" wide x 29-18" high x 4" deep). Allows 14" shim spacearound dispenser; shim at screw points as required.
45 Utilitech wall framing at head of treatment room (Typ.)
46 Dimensions from F.O. Utilitech wall framing to F.O. studof rough framing.
47 Wood light valance. See details, sheets D8 & D9.
Fully adhered mirror w/ radius machined edges.
Apply bead of clear silicone between mirror & backsplash.
48
J-box & power to be let into mirror for valance light.49
Provide hardboard standoff behind mirror, flush w/ faceof tile. Hold back 12" from all mirror edges. (Typ.)
Tile wainscot is continuous behind mirror. (Typ.)50
Provide 'CRL' #KJ9 nickel-plated mirror clips (or equal)
Removable wood panel, see section and finish sched.51
Engineered quartz backsplash.
112" wood face frame.52
Open shelf cabinet w/ wood all faces.53
3/4" wood adjustable shelves w/ 1-1/2"H wood face(as stiffener).
54
Plastic laminate faced cubbie locker cabinet (see planfor locker depth).
55
Cabinet lock (Typ.) Provide separate keyed cylindersat each locker.
56
Open cubbie, no door/lock, plastic laminate all faces.57
58
ALL WALL CABINET INSTALLATION(SEE ALSO GEN. NOTE #'S 9 & 19; SHT. D1)
PROVIDE REQ'D BLOCKING FOR
ALL DRAWINGS ON THIS SHEETARE DRAWN AT 1/2" = 1'-0"
NOTES:
14
27
2'-6
"2'
-0"
2'-6
"
22 22
12
3'-0
"
OPEN TO WALL
(FOR DVD SYSTEMBY OWNERO.S.C.I.)
OPEN
VERIFY W/ OWNER
OPEN FOR D.W. (O.S.C.I.)
ALI
GN
2 EQUAL
6"
6 L
1'-4
"
3'-0"2 EQUAL
5D81'
-6"
2'-6
"
VE
RIF
Y W
/O
WN
ER
2 EQUAL
4 EQUAL
1D8
15
ALI
GN
33% OFFSET(TYP.)
6"x36" 6"x36"
6"x36" 6"x36" 6"x36"
6"x36" 6"x36" 6"x36"
6"x36" 6"x36"
6"x36"
6"x36" 6"x36"
6"x36" 6"x36"
6"x36"
6"x36"
6"x36"
TI CABINETS
D13
THESE PLANS ARE INSTRUMENTS OF PROFESSIONAL SERVICEAND ARE PROTECTED BY COMMON LAW, STATUTORY AND
OTHER RESERVED RIGHTS INCLUDING COPYRIGHT. THEY MAYNOT BE REPRODUCED OR USED FOR ANY PURPOSE WITHOUT
THE WRITTEN CONSENT OF THE DESIGN PROFESSIONAL©2014
5930 VanDervoort DriveLincoln, Nebraska 68516ph 402 423 3300 fax 402 423 3377
UNTHANK
Michael Unthank DDS© Copyright 2014Michael Unthank DDS NCARB
ACCESSORY KEYNOTES
Doug Mockett Co. (800.523.1269) www.mockett.com
ACCESSORY NOTES:
L Doug Mockett #TM1B-SSS trash drop. (See details#5/D9, #6/D9 & #9/D9 for some specific placements.)
Shaker style wood cabinets. (w/ matching wood interiors.)
Plastic laminate faced cabinets. (w/ melamine interiors)
Adjustable shelf/shelves.
Finish end panel, to match, typical.
Wall base.
Plastic laminate backsplash.
Gyp. board.
KEYNOTES
15
5
19
2
1
14
13
27
24
Plastic laminate countertop w/ wood edge.4
3 Plastic laminate countertop w/ full bullnose.
7 Plastic laminate countertop & apron.
1-1/2" wood face frame.8
Open shelf cabinet w/ plastic laminate all faces.10
Post-formed plast. lam. countertop w/ full bullnose &integral backsplash.
6
9
Exterior windows not detailed/scheduled on "D" sheets.
Provide matching plast. lam. on back of all cabinets& backsplash crossing exterior windows, typical.
12
25
26
21
22
23
11
Plastic laminate; this surface.16
End-support panel to floor.17
18
20
Chamfered corner panel from 2" stock.
Hold cabinets clear of window trim (Typ.)
1" MDF adjustable shelf with matching plast. laminate topand bottom. Front face with plast. lam. or pvc edging.
See note #23 on sheet D1. Coordinate cabinetry withrefrigerator door operation.
Wood or metal counter supports (contractor's option).See finish schedule for color. (4'-0" ctr. spans max.)
Referenced this sheet
Open shelf cabinet w/ wood all faces.
3/4" wood adjustable shelves w/ 1-1/2"H wood face(as stiffener).
( not used )
( not used )
( not used )
FLOOR TILE DETAIL1" = 1'
4.0"
SYMBOL
KEYNOTE