Upload
anonymous-sa0yoekp
View
11
Download
0
Embed Size (px)
DESCRIPTION
This work summarizes the results of a geomorphological and bivariate statisticalapproach to gully erosion susceptibility mapping in the Turbolo stream catchment(northern Calabria, Italy). An inventory map of gully erosion landforms of the area hasbeen obtained by detailed field survey and air photograph interpretation. Lithology, landuse, slope, aspect, plan curvature, stream power index, topographical wetness index andlength-slope factor were assumed as gully erosion predisposing factors. In order to estimateand validate gully erosion susceptibility, the mapped gully areas were divided in twogroups using a random partitions strategy
Citation preview
ORI GIN AL PA PER
Geomorphology and GIS analysis for mapping gullyerosion susceptibility in the Turbolo stream catchment(Northern Calabria, Italy)
Massimo Conforti Pietro P. C. Aucelli Gaetano Robustelli
Fabio Scarciglia
Received: 7 December 2009 / Accepted: 6 August 2010 / Published online: 27 August 2010 Springer Science+Business Media B.V. 2010
Abstract This work summarizes the results of a geomorphological and bivariate statis-tical approach to gully erosion susceptibility mapping in the Turbolo stream catchment
(northern Calabria, Italy). An inventory map of gully erosion landforms of the area has
been obtained by detailed field survey and air photograph interpretation. Lithology, land
use, slope, aspect, plan curvature, stream power index, topographical wetness index and
length-slope factor were assumed as gully erosion predisposing factors. In order to estimate
and validate gully erosion susceptibility, the mapped gully areas were divided in two
groups using a random partitions strategy. One group (training set) was used to prepare the
susceptibility map, using a bivariate statistical analysis (Information Value method) in GIS
environment, while the second group (validation set) to validate the susceptibility map,
using the success and prediction rate curves. The validation results showed satisfactoryagreement between the susceptibility map and the existing data on gully areas locations;
therefore, over 88% of the gullies of the validation set are correctly classified falling in
high and very high susceptibility areas. The susceptibility map, produced using a meth-
odology that is easy to apply and to update, represents a useful tool for sustainable
planning, conservation and protection of land from gully processes. Therefore, this
methodology can be used to assess gully erosion susceptibility in other areas of Calabria, as
well as in other regions, especially in the Mediterranean area, that have similar morpho-
climatic features and sensitivity to concentrated erosion.
M. Conforti (&) G. Robustelli F. ScarcigliaDipartimento di Scienze della Terra, Universita` della Calabria, Via P. Bucci, Cubo 15B,87036 Arcavacata di Rende (CS), Italye-mail: [email protected]
G. Robustellie-mail: [email protected]
F. Scarcigliae-mail: [email protected]
P. P. C. AucelliDiSAm, Universita` degli Studi di Napoli Parthenope, Centro Direzionale isola C/4,80143 Naples, Italye-mail: [email protected]
123
Nat Hazards (2011) 56:881898DOI 10.1007/s11069-010-9598-2
Keywords Gully erosion susceptibility GIS Information value method Calabria
1 Introduction
Gully erosion is one of the erosive processes that mostly contributes to shape the earth
surface (Billi and Dramis 2003). The development of gullies causes the loss of a great
amount of soil and can be considered as one of the principal causes of geo-environmental
degradation in the Mediterranean area (Vandekerckhove et al. 2000; Martnez-Casasnovas
et al. 2003; Vanwalleghem et al. 2005). Researches conducted in SE Spain, SE Portugal
and central Belgium determined that gully erosion generated between 3.4 and 9.7 m3/ha/
year of sediments, representing 4483% of total sediment production on agricultural lands
(Poesen et al. 1998). Generally, the growing interest in studying gully erosion reflects the
need to increase our knowledge on its impacts and controlling factors that vary under a
wide range of causes (Valentin et al. 2005). Gullies are common features on slopes of
mountainous or hilly regions worldwide and involve complex processes controlled by a
variety of closely related factors such as lithology, soil type, climate, topography, land use
and vegetation cover.
Also large areas of South Italy and, in particular, the Calabria territory, which is on the
whole very susceptible to erosion processes (Sorriso-Valvo et al. 1995; ARSSA 2005;
Terranova et al. 2009), are vulnerable to the development of gully erosion, due to the
combination of its peculiar geological, morphological, pedological, climatic characteristics
and very often to unsustainable land management. A recent study by Conforti (2008)
showed that wide portions of the Turbolo stream catchment in northwestern Calabria
(which is highly representative of different areas in the regional territory, in light of its geo-
environmental features and high soil erosion susceptibility conditions) are affected by
erosive processes that occur as linear and/or diffused water erosion. In particular, con-
centrated runoff (mainly responsible for gully erosion) causes a consistent soil loss,
reaching more than 20 t/ha/year on slopes affected by calanchi (Alexander 1980; Morettiand Rodolfi 2000). Therefore, it is of prominent importance to define valid models to
assess the susceptibility of the territory to the development of these processes.
The main objectives of this study have been (a) identification, morphological descrip-
tion and mapping of the areas affected by gullies in the Turbolo stream catchment;
(b) characterization of the main geo-environmental features as factors that control gullies
distribution; and (c) evaluation of gully erosion susceptibility in the study area.
2 Geo-environmental setting of the study area
The Turbolo stream catchment is located in the northwestern portion of Calabria (South
Italy), between 393202300N and 392904900N latitude, 161205700E and 160502100E longi-tude (Fig. 1). The Turbolo stream is a left-side tributary of the Crati river and originates in
the eastern top slope of the Calabrian Coastal Range at more than 1,000 m of altitude,
flowing longitudinally from west to east for a length of about 13 km. Its catchment extends
over an area of about 30 km2, having an elongated and asymmetrical shape. The Turbolo
stream represents a basin of the 5th order with a drainage density equal to 5.16 km-1,
which indicates a rather dense drainage network in a strongly dissected area (Conforti
2008), often controlled by tectonic activity (Tortorici et al. 1995). The drainage pattern is
882 Nat Hazards (2011) 56:881898
123
dendritic in mountain sub-basins and trellis-like in hilly sub-basins. The climate is an
upland Mediterranean type (Csb, sensu Koppen 1936), with hot, dry summers and pre-cipitations concentrated in mild winters. Mean annual rainfall is about 1,200 mm, with
extremes exceeding 1,600 mm/yr. The rainfall is distributed in 105 rainy days; more than
60% of precipitations fall in the winter period from November to February (December
being the rainiest month reaching 200 mm), snowfall included above 700800 m a.s.l.
Mean annual temperature is 16C, and mean monthly temperatures range between 7C inJanuary and 26C in August (Caloiero et al. 1990; Conforti 2008).
From a geological point of view, the study area is crossed by an important NS Qua-
ternary strike fault (S. FiliS. Marco Argentano, Tortorici et al. 1995); it is responsible for
Fig. 1 Study area location map and spatial distribution of the gully area on the DTM of the Turbolo streamcatchment
Nat Hazards (2011) 56:881898 883
123
the uplift of the plutonic and metamorphic basement of the Calabrian Coastal Range (west)
with respect to the post-orogenic formations filling the Crati graben (east). Among the
latter, the following terrains outcrop in the study area, from bottom to top (Colella et al.
1987): Late Miocene marine clay and silt, interbedded with chalk and calcarenite layers;
Late Pliocene-Late Pleistocene marine silty clay, passing to sand, silt and conglomerate
and fan-conglomerate, made of igneous and metamorphic clasts in a sandy matrix
(Lanzafame and Zuffa 1976); Holocene alluvial and colluvial deposits occur along the
valley bottoms.
Outcrops of crystalline basement rocks of the Costal Range are limited to the western
part of the study area, where the following tectonic units can be recognized (Amodio-
Morelli et al. 1976): gneiss and schist of the Polia-Copanello and Castagna Units
(Paleozoic), phyllite interbedded with metapelite and quartzite of the Bagni Unit (Triassic),
micaschist interbedded with quartzite, metapelite and metalimestone of the Frido Unit
(Cretaceous), metabasite covered by metalimestone and by polychrome schist of the
Diamante-Terranova Unit. These rocks are intensely fractured and weathered and, very
often, are affected by landslides and deep-seated gravitational slope deformations (Iovine
et al. 2006; Gattinoni 2008).
From a morphological point of view, the western sector of the study area is charac-
terized by steep slopes (average [30), shaped on metamorphic rocks and a high localrelief caused by the strong uplift of the Coastal Range and its consequent dissection
(Tortorici et al.1995). In particular, these slopes show a rectilinear-convex profile and are
often highly dissected by V-shaped valleys (Sorriso-Valvo and Tansi 1996). Gentleslopes, where clayey lithologies outcrop, generally characterize the intermediate western
sector of the basin; denudational processes, mainly landslides and water erosion, sig-
nificantly affect hill slopes. Slope profiles are generally very articulated, with concave-
convex shapes (Sorriso-Valvo and Tansi 1996) and mainly incised by valleys with
concave bottom.
In the eastern sector of the Turbolo watershed, the landscape is characterized by the
presence of terraced surfaces, deeply dissected by V-shaped or concave valleys, caused bythe Quaternary tectonic activity (Carobene et al. 1989). Recent alluvial fans and fluvial
terraces (Holocene) are observed along the main river valleys.
As a result of the different geological, morphological and climatic conditions, several
soil types can be found in the Turbolo basin. According to the soil map of Calabria
(ARSSA 2003), soils range from highly mature (Alfisols) to poorly developed soils
(Inceptisols and Entisols) (sensu USDA 2006), which frequently appear truncated orstrongly degraded at surface by water erosion. Moreover, on the clayey hill slopes most
soils show outstanding vertic features, with a high structural dynamism characterized by
the development of desiccation cracks (due to shrinkage of clays) from the surface in the
dry season, that are subsequently closed by imbibition and consequent swelling of clays in
the following wet season.
In the study area, the main erosive processes that affect the landscape are related to
runoff waters (diffuse and/or linear) and mass movements that cause a rapid evolution of
slopes and valley bottoms (Conforti 2008). Overland flow processes (sheet, rill and gully
erosion) particularly act in areas without vegetation cover, in cultivated fields and pasture
lands. The main causes of water erosion are the intensive land use and cultivation of annual
crops on steep slopes often performed along slope-parallel plowing furrows. Mass
movements are triggered mainly on clayey slopes and on steeply inclined and intensely
weathered metamorphic substrata.
884 Nat Hazards (2011) 56:881898
123
3 Materials and methods
The first phase of the research has been carried out through a geomorphological study. Air
photograph interpretation and field survey have brought to the assessment of the spatial
distribution of gully erosion processes, allowing an inventory map of gully landforms to be
constructed (Fig. 1). The mapped gully area consists of slope units widely affected by
gully erosion, which represent microbasins.
Because gullying is a threshold-dependent process controlled by a wide range of factors
(Valentin et al. 2005), to assess gully erosion susceptibility, it has been necessary to select
a number of predisposing factors of different nature (geological, morphological, hydro-
logical, etc.), which are suspected to be somehow related to the generation of gully erosion
processes. The predisposing factors used in this work are lithology, land use and a series of
topographical factors: slope, aspect, plan curvature, stream power index (SPI), topo-
graphical wetness index (TWI) and length-slope factor (LS), also known as transmission
capacity index (Moore et al. 1991). All the morphometric parameters were automatically
derived from the DTM with a resolution of 10 9 10 m pixel size, using the management
features offered by the DTM extensions (3D Analyst, Spatial Analyst and Sinmap) of the
ESRI Arcview 3.2 GIS software. The DTM has been produced from digitization of contour
lines and points of the topographical map of Calabria at 1:10000 scale, dating back to
1954; contour lines have been updated by using the Z-map software that allowed to obtain
3D polylines from the stereoscopic models of aerial photographs of 2005. Consequently,
the DTM can be considered as shaped by the gully landforms.
3.1 Analysis of predisposing factors
3.1.1 Lithology
A detailed analysis of the major lithological characteristics has been performed by inte-
grating data from the geological map of Calabria at 1:25000 scale with field survey. In fact,
lithological properties are among the main sources of data related to the geomorphological
features and evaluation of a land (Dai et al. 2001). Special focus has been devoted to
mapping superficial deposits (colluvial, alluvial, slope and landslide deposits), these are
considered as particularly prone to erosion processes.
Gully erosion is particularly related to the lithology and weathering properties of the
material exposed or close to the earth surface. Therefore, the large variety of lithological
types cropping out in the study area has been grouped into eleven classes according to their
compositional characteristics, mechanical properties and expected erodibility (Fig. 2a;
Table 1). Sands and clays are the most widespread lithologies. Pleistocene sand deposits
crop out for the 39% of the study area and mostly in the eastern zone. Pliocene clayey
sediments mainly outcrop in the central sector of the basin reaching about 14% of the basin.
3.1.2 Land use
The type of soil use has a significant influence on the geomorphological stability of a slope;
in general, barren and sparsely vegetated areas are affected by faster erosion and greater
instability than forests (Anabalagan 1992; Dai et al. 2001; Cevik and Topal 2003). The
existence of a plant cover has decreasing effects on gully erosion susceptibility, because it
reduces the erosive action of surface runoff. In the study area, a land use map has been
Nat Hazards (2011) 56:881898 885
123
derived from color orthophotograph interpretation and field checks. Land use types were
thus grouped into nine classes (Fig. 2b; Table 1). In particular, more than 55% of the area
presents an agricultural and pastoral use, in which the large part of the gullies is included.
3.1.3 Slope
The steepness of slopes is a factor of primary importance in the dynamics of the processes
governing land evolution; in fact, it affects surface runoff, drainage density, soil erosion
etc., (Dramis and Gentili 1977). For this reason, the steepness of the slopes plays a crucial
role in the preparation of the erosive process susceptibility maps in a given territory, in the
specific case of gully erosion. Therefore, steep slopes promote high runoff velocity and
consequent rill and gully initiation (Valentin et al. 2005). In this study, the slope, derived
from the DTM, has been divided in six classes (Fig. 2c). In the Turbolo catchment, gullies
are common in the hilly land with steep slopes (Table 1).
Fig. 2 Predisposing factor maps: a lithology; b land use; c slope; d aspect; e plan curvature; f LS; g SPI;h TWI
886 Nat Hazards (2011) 56:881898
123
Table 1 Weighting values (Wi) distribution for each class of the selected gully erosion predisposing factors
NpixNi NpixSi DensClass Wi
Lithology
Alluvial deposit 21,293 197 0.009 -1.31
Colluvial deposit 15,291 130 0.009 -1.39
Alluvial fan deposit 20,586 607 0.034 -0.15
Slope deposit 8,891 109 0.012 -1.03
Landslide deposit 17,444 331 0.005 -0.59
Conglomerates 24,151 925 0.038 0.11
Sands 109,829 5,713 0.052 0.42
Clays 40,312 1,566 0.039 0.13
Gneiss 12,157 37 0.003 -2.42
Metalimestone and metapelite 12,347 274 0.026 -0.43
Phyllite/Schist and metabasite 9,273 384 0.052 0.19
Land use
Woodland 81,723 3,590 0.044 0.26
Scrub and herbaceous 36,396 2,807 0.077 0.81
Pasture 28,912 752 0.026 -0.28
Olive groves 62,395 734 0.012 -1.06
Orchard and/or vineyard 3,658 41 0.011 -1.12
Cropland 65,054 925 0.014 -0.88
Barren and abandoned land 7,323 1,441 0.200 1.75
River bed and flooding areas 2,100 5 0.003 -2.62
Urban 6,860 0 0.000 -2.70
Slope
05 45,489 275 0.006 -1.74510 42,930 520 0.012 -1.041015 57,880 1,043 0.018 -0.641520 56,521 1,703 0.030 -0.132030 71,902 4,568 0.064 0.62[30 25,059 2,164 0.086 0.92
Aspect
Flat 27,301 821 0.030 -0.13
N 38,148 986 0.026 -0.28
NE 38,596 1,161 0.030 -0.13
E 47,861 1,216 0.025 -0.30
SE 52,931 1,785 0.034 -0.02
S 29,893 1,411 0.047 0.32
SW 11,944 1,124 0.094 1.01
W 13,435 880 0.066 0.65
NW 30,257 876 0.029 -0.17
SPI
00.6 188,207 4,047 0.022 -0.47
0.61.2 87,477 4,731 0.054 0.46
1.21.8 16,394 1,217 0.074 0.77
Nat Hazards (2011) 56:881898 887
123
3.1.4 Aspect
Aspect is also considered an important factor in susceptibility studies of denudational
processes (Carrara et al. 1991; Maharaj 1993; Guzzetti et al. 1999; Nagarajan et al. 2000).
Aspect is expressed in degrees from north and clockwise, ranging from 0 to 360. The value
of -1 is used to identify flat surfaces such as flood plains, fluvial terraces. The aspect of a
slope can indirectly influence gully erosion processes, because it controls the exposition to
several climate conditions (duration of sunlight exposition, precipitation intensity, mois-
ture retention, etc.) and the vegetation cover (Dai et al. 2001; Cevik and Topal 2003; Pulice
et al. 2009). Consequently, slope aspect can play a prominent role in rock weathering and
the formation of pedo-regolithic cover. The aspect map of the study area was classified into
nine classes: flat, N, NE, E, SE, S, SW, W and NW (Fig. 2d and Table 1). On this basis, the
aspect classes of the Turbolo stream catchment highlight a fairly homogeneous distribu-
tion. Slopes facing from east to south-east slightly predominate. West and south-west
facing slopes are relatively less frequent.
3.1.5 Plan curvature
Slope plan curvature has been investigated with respect to its effect on gullies triggering
and development (Fig. 2e). The term curvature is theoretically defined as the rate of change
of slope gradient or aspect, usually in a particular direction (Wilson and Gallant 2000).
The curvature value can be evaluated by calculating the reciprocal value of the radius of
curvature of that particular direction and has been obtained directly from the derivatives of
Table 1 continued
NpixNi NpixSi DensClass Wi
1.82.4 2,935 228 0.078 0.82
2.43 432 34 0.079 0.83
33.6 55 6 0.109 1.16
TWI
00.2 78,497 2,014 0.026 -0.29
0.21 75,372 1,616 0.021 -0.47
12 10,804 312 0.029 -0.17
23 126,864 6,321 0.050 0.37
LS
0.0.2 134,380 2,998 0.022 -0.43
0.23 153,986 6,826 0.044 0.26
35 1,995 235 0.118 1.24
510 907 143 0.158 1.53
[10 303 70 0.230 1.90Plan curvature
Concave 26,837 3,824 0.142 1.43
Convex 80,580 2,342 0.029 -0.16
Flat 190,499 4,097 0.022 -0.47
Total areaP
NpixNi = 299,780P
NpixSi = 10,272 DensMap = 0.034
888 Nat Hazards (2011) 56:881898
123
a topographical surface (Wilson and Gallant 2000). Plan curvature is described as the
curvature of a contour line formed by intersecting a horizontal plane with the surface. The
influence of plan curvature on slope erosion processes is the convergence or divergence of
water during downslope flow. Positive ([0) values of plan curvatures define convexity,negative (\0) values of plan curvatures characterize concavity of slope curvature. Valuesof plan curvatures around zero indicate that the surface is flat. The relationship between
gullies and plan curvatures in the Turbolo catchment shows that gully erosion processes
commonly occur on concave slopes (Table 1).
3.1.6 Length-slope factor
The length-slope factor (LS) is a parameter used in the RUSLE equation to consider the
effect of topography on erosion (Renard et al. 1997). The topographical factor depends on
the slope steepness factor (S) and the slope length factor (L). It is essential to quantify
erosion generated by its influence on surface runoff speed and is considered a sediment
transport capacity index. There are different approaches found in literature for determining
the LS factor in a grid-based DEM. One of them is based on the upslope contributing area
of each cell, which can be calculated with the equations described by Moore and Burch
(1986):
LS fa cellsize=22:13 0:4 sin r=0:0896 1:3
where fa is flow accumulation and is derived from the DEM using a GIS accumulation
algorithm (Lee 2004) and r is slope in degrees. The LS factor was estimated on the basis ofthe flow accumulation and slope steepness (Moore and Burch 1986). Flow accumulation
was computed using the watershed delineation tool of Arcview 3.2. The spatial pattern of
the LS factor is shown in the map of Fig. 2f, and its values have been classified in five
classes. Gullies commonly occur on slopes with high LS values (Table 1).
3.1.7 Stream power index
The stream power index (SPI) (Fig. 2g) is a measure of the erosive power of water flow
based on the assumption that discharge is proportional to the specific catchment area (As)
(Moore et al. 1991).
SPI As tan rwhere As is the specific catchment area in meters and r is the slope gradient in degrees.The index SPI is one of the main factors controlling slope erosion processes, since erosive
power of running water directly influences slope toe erosion and river incision (Nefeslioglu
et al. 2008). It is also indicative of the potential energy available to entrain sediment, so
that areas with high stream power indices have a great potential for erosion (Kakembo
et al. 2009). The values of SPI factor have been classified in six classes. The overlay
between gullies inventory map and the SPI factor map shows that gully erosion processes
frequently occur on slopes with high SPI values (Table 1).
3.1.8 Topographical wetness index
The topographical wetness index (TWI) has been used extensively to describe the effect of
topography on the location and size of saturated source areas of runoff generation. TWI is a
Nat Hazards (2011) 56:881898 889
123
function of both the slope and the upstream contributing area per unit width orthogonal to
the flow direction. We used this index for this study, because TWI has been proven to be
correlated with soil erosion processes. Moore et al. (1991) proposed for the calculation of
TWI the assumption of steady state conditions and uniform soil properties (i.e. transmis-
sivity is constant throughout the catchment and equal to unity). The implementation of
TWI can be shown as:
TWI lnAs= tan rwhere As is the specific catchment area in meters and r is the slope gradient in degrees.The highest values of TWI index have been mostly recorded in valley bottoms, terraced
surfaces and gentle slopes (Fig. 2h). The values of TWI have been classified in four classes
(Table 1).
3.2 Susceptibility analysis
The second phase of this work was carried out with the implementation of a geo-database
with all the acquired data and the application of a bivariate statistic method (Information
Value, hereinafter InfVal) in GIS environment to estimate the gully erosion susceptibility.
The bivariate procedure is the simplest and the most quantitatively suitable method to
assess geomorphic processes susceptibility, even though a multivariate analysis can be
considered much more rigorous, because predisposing factors are cross-checked simulta-
neously; therefore, we have considered the main advantages of a bivariate-statistics-based
approachits easy updating of susceptibility maps and its ease to be used for land-
planningin respect with the complexity of a multivariate method, based on greater
knowledge of mathematics and statistics. Our choice is also based on the findings provided
by Su`zen and Doyuran (2003), according to which the two statistical methods (bivariate
and multivariate) produce susceptibility maps that converge in 80% of a given study area.
Up to now, the statistical bivariate analysis has been widely adopted to assess landslide
susceptibility (Yin and Yan 1988; Van Westen 1993, 1997; Rautela and Lakhera 2000;
Zezere et al. 2004; Cevik and Topal 2003; Wang and Sassa 2005; Magliulo et al. 2008;
Yalcin 2008). This statistical approach is based on the observed relationships between each
predisposing factor and the distribution of gully areas. The single thematic maps previously
produced for each predisposing factor (lithology, land use, slope, aspect, plan curvature,
SPI, TWI and LS) have been converted in raster format and combined with the whole
gullies inventory map in order to calculate the density of the gully areas for each class of
the predisposing factors; the computed density represents the susceptibility level of the
considered predisposing factor class (Carrara et al. 1995). This procedure has allowed to
obtain all the parameters needed to calculate the weighting values (Wi) for each class of
the selected predisposing factors by means of the InfVal method. In this method, a weight
value for a parameter class is defined as the natural logarithm of the gullies density class
divided by the area of gullies density over the entire study area (Van Westen 1993; Rautela
and Lakhera 2000) and can be expressed with the following formula (Yin and Yan 1988;
Van Westen 1993):
Wi ln DensClasDensMap
ln NpixSi=NpixNiPNpixSi=
PNpixNi
in which W` = weighting value of the class i; DensClas = density of the gullies in theclass i; DensMap = density of the gullies in the whole study area; NpixSi = number of
890 Nat Hazards (2011) 56:881898
123
pixels that contains gullies in the class i; NpixNi = number of pixels within the class i;PNpixSi = total number of pixels that contain gullies in the whole study area;PNpixNi = total number of pixels of the whole study area. Each predisposing factor map
has been then reclassified on the basis of the calculated weighting values. Overlay pro-
cedures of the reclassified maps, performed in GIS environment, allowed to calculate, for
each point of the study area, the sum of the weighting values occurring in that given point,
thus obtaining the susceptibility value. The attained ranges of values have been subdivided
into five susceptibility classes (very low, low, moderate, high and very high), using the
natural-breaks technique (Jenks 1989). This technique identifies break point values by
picking the class limits that maximize the differences between classes and minimize the
within-class sum of squared differences. Five gully erosion susceptibility classes (Federici
et al. 2007) have been so obtained allowing to produce the gully erosion susceptibility map
of the Turbolo stream catchment.
In order to validate the susceptibility map, the gully areas dataset has been split into two
subsets using a random partition (Chung and Fabbri 2003). One subset (training set, 65%of all) has been used to obtain the weight and the susceptibility map, by means of the
InfVal method, and the second subset (validation set, remaining 35%) has been used to
validate the susceptibility map analyzing the shapes of success and prediction rate curves(Chung and Fabbri 2003). The prediction model is produced independently from the gullies
of the validation set, so that it can be treated as the result of future gully erosion
processes (Conoscenti et al. 2008).
The gully areas in the validation set and the training set have been, respectively,
overlaid with the susceptibility map, and the area of gullies per susceptibility class has
been derived using zonal statistics. This procedure has allowed to draw the prediction andthe success rate curves. The prediction rate curve allowed us to assess the predictionperformance of the method. A binary diagram has been plotted representing the cumu-
lative percentage of the gully areas in the validation set (y-axis) with respect to thecumulative percentage of the study area (x-axis), ordered according to the decreasingsusceptibility ranking (Remondo et al. 2003). The success rate curve has been obtainedby following the same procedure, but considering the gully areas training set, which have
been used in the prediction model. The success rate curve has been used to indicate thegoodness of fit of the gully erosion susceptibility map (Chung and Fabbri 2003; Remondo
et al. 2003).
4 Results and discussion
4.1 Gully erosion processes
The geomorphological analysis (aerial photographs interpretation and systematic field
checks) shows that the 5% (about 1.45 km2) of the area of the Turbolo stream basin is
affected by many permanent gullies (Figs. 1, 3); they are often characterized by incisions
with subvertical sidewalls and depth locally overcoming 8 m. In the eastern sector of the
basin, where sands and conglomerates outcrop, gully channels are narrow and usually
V-shaped, with almost bare side slopes indicating an active stage of dissection (Fig. 3a).Gullied areas are mainly characterized by dentritic and trellis drainage patterns. Gully
formation is often enhanced from November to February, the rainy season, when many
cultivated fields are unprotected because of seeding practices. Moreover, during heavy rain
events, many gullies reactivate and, in addition to vertical dissection, may frequently
Nat Hazards (2011) 56:881898 891
123
undergo headcut and valley-side retreat processes causing their lengthening and widening
(Fig. 3b). The presence of tension cracks on top of gully sides often tends to increase
falling phenomena (Collison 2001; Bull and Kirkby 2002; Poesen et al. 2002).
The most evident and spectacular landforms related to gully erosion in the study area
are represented by badlands (calanchi), almost exclusively developed into clayey litho-types (Fig. 3c) with a channel network mainly characterized by a parallel pattern. Both
concentrated runoff and falls/topples along tension cracks can be enhanced by the
occurrence of desiccation cracks (due to shrink/swell dynamics of expandable clays)
developed during dry seasons (Pulice et al. 2009).
The calanchi are often developed along ancient landslide scars, which promoted con-centration of running water (Morgan 2005). The geomorphological survey inside the
badland areas put in evidence that, within the main gullies, small mass movements and
dissecting processes work together to give blunted ridges. On the contrary, vertical dis-
section processes prevail in secondary channels, thus forming narrower and knife-edge
ridges. Moreover, along badland slopes micro-piping and rilling processes operate,
whereas debris flow cones are often accumulated at the mouth of various order drainage
channels (Fig. 3d).
Fig. 3 Gully erosion processes in the Turbolo stream catchment; a Gully formed by retrogressive erosionwith narrow and V-shaped channels; b Active gully erosion during heavy rain events, with evident falls thatcause headcut and flank retreat processes (indicated by red arrows); c Badlands in the clayey lithology;d Debris flow cones accumulated at the mouth of badland channels
892 Nat Hazards (2011) 56:881898
123
4.2 Gully erosion susceptibility assessment
The density of gully areas and the weighting values obtained using the Information Value
method are reported in Table 1, indicating the magnitude of the class of each predisposing
factor. Positive or negative values of Wi indicate that the considered class of each predis-
posing factor is relevant or not in the development of gullies, respectively (Zezere et al. 2004).
The highest density of gullies, highlighted by Wi = 0.42, occurs in areas where sand
deposits crop out. This result is in accordance with the concentration of about 60% of the
gullies mapped on this lithology. In addition, the highest Wi occurs on the slopes with
concave plan curvature (Wi = 1.43) and slope gradient[30 (Wi = 0.92) consistent sinceof steep and concave slopes that increase the volume and velocity of surface runoff,
causing soil concentrated erosion and high sediment loss (Ndomba et al. 2009). A strong
spatial correlation exists between the gully erosion processes and areas with high value of
SPI. The relevant role of the SPI factor on gully processes is confirmed by positive values
of Wi for all values of SPI, higher than 0.6. Land use factor plays an important role in gully
processes, mainly on barren and abandoned lands (Wi = 1.75), where soil surface is
exposed to raindrop impact and possible accelerated runoff (depending on slope steepness).
On the contrary, gullies density is particularly low where the gneiss bedrock crops out
(Wi = -2.42), on which the LS is low (Wi = -0.43) and SPI is low (Wi = -0.47).
Furthermore, the lowest Wi occurs where slope ranges between 0 and 5 (Wi = -0.84).As a result of the overlay of each predisposing factor map, reclassified on the basis of
the calculated weighting values, a gully erosion susceptibility map has been produced for
the Turbolo watershed (Fig. 4). The weighting values obtained have a minimum of
Fig. 4 Gully erosion susceptibility map of the Turbolo catchment
Nat Hazards (2011) 56:881898 893
123
-12.16 and a maximum of 7.39, with an average value of -0.85 and a standard deviation
of 2.81. The computed pixel values have been classified into five groups of susceptibility
that are distributed in the study area as follows: 17% very low, 18% low, 24% moderate,
34% high and 7% very high; therefore, a relevant part of the study area, mainly located in
eastern sector, falls in high to very high susceptible zones. Moreover, susceptibility is
very high in the northern and western portions of the catchment, where clay deposits
mainly outcrop.
The susceptibility map obtained has been further validated. The predictive power of
the susceptibility map has been tested by analyzing their success rate and prediction rate
curves (Chung and Fabbri 2003). This comparison has allowed to verify the spatial
distribution of the gully areas in the susceptibility ranked levels (Conoscenti et al. 2008).
The calculation of the success rate and prediction rate curves for the Turbolo watershed is
shown in Fig. 5. They have very similar shape, showing a high gradient in the first part
and smoothly decrease monotonically. The prediction curve shows that 70% of the total
gully area of the validation set falls within 20% of the most susceptible areas (Fig. 5).
This result confirms both the validity of the susceptibility method and the high spatial
correlation between predisposing factors used for the analysis and the gullies. Further-
more, the validation procedure results show that the predictive power of the model is
generally satisfactory; therefore, about 90% of the gully area of the validation set is
correctly classified falling in high and very high susceptibility classes. This good result
could be overweighted if we consider that the predisposing factors could have some
relationship between each other, in particular slope has been computed also in LS, TWI
SPI factors.
5 Conclusions
In this study, the geomorphological (field survey and air photograph interpretation) and
GIS analyses allowed to characterize the morphological features and spatial distribution of
Fig. 5 Prediction rate and success rate curves that representing the accuracy of the susceptibility modelused (see text for details)
894 Nat Hazards (2011) 56:881898
123
gully areas and the main geo-environmental factors that predispose the slopes to their
development in the Turbolo stream catchment (northern Calabria, Italy). Current gully
landforms affect 5% of the watershed. Gully erosion activity is controlled mainly by
geomorphological features and land use. The relationships between gullies and the selected
geo-environmental analyzed factors (lithology, slope gradient, aspect, plan curvature, SPI,
TWI, LS and land use) have been assessed using the Information Value method synthe-
sized in a gully erosion susceptibility map. In this analysis, the important role played by the
geomorphological parameters (slope gradient, slope plan curvature, SPI, etc.) in the gully
erosion processes has been highlighted. It has been observed that the gully erosion pro-
pensity increases rapidly for hill slopes above 20 and on slopes with concave shape.Therefore, the SPI and LS factors have a strong control on the susceptibility to gully
erosion. Lithology and land use appear to play an important role in controlling gully
erosion; in particular, land surfaces shaped in clay and sand deposits, barren and/or covered
by sparse vegetation resulted to be the most prone to gully erosion.
The proposed methodology to assess gully erosion susceptibility, based on a bivariate
statistical method implemented in GIS environment, has been applied using a training data
set and validated with a validation set of gully areas. The results are indicative of the high
quality of the map obtained and showed satisfactory agreement between the susceptibility
map and the gully location data. A validation procedure, based on the analysis of the
shapes of a success and a prediction rate curve, implemented to evaluate the goodness of fit
and the predictive power of the susceptibility map, respectively, showed that the prediction
image is a satisfactory predictor of future gully activity. Therefore, over 88% of the gullies
of the validation set are correctly classified falling in high and very high susceptibility
classes.
Finally, the results showed that the choice of suitable predisposing factors together with
the bivariate statistical method and the application of geographical information systems are
able to successfully identify areas that are susceptible to gully erosion. The produced
susceptibility map, using a methodology easy to apply and to update, represents a useful
tool for sustainable planning, conservation and protection of land from gully processes.
Therefore, this methodology can be used to assess gully erosion susceptibility in other
areas of Calabria, as well as in other similar regions, especially in the Mediterranean area.
References
Alexander DE (1980) Calanchi-accelerated erosion in Italy. Geography 65:95100Amodio-Morelli L, Bonardi G, Colonna V, Dietrich D, Giunta G, Ippolito F, Liguori V, Lorenzoni S,
Paglionico A, Perrone V, Piccarreta G, Russo M, Scandone P, Zanettin Lorenzoni E, Zuppetta A(1976) Larco Calabro- Peloritano nellorogene appenninico-maghrebide. Memorie della Societa`Geologica Italiana 17:160
Anabalagan R (1992) Landslide hazard evaluation and zonation mapping in mountainous terrain. Eng Geol32:269277
ARSSA (2003) Carta dei suoli della regione Calabriascala 1:250000. Monografia divulgativa. ARSSA-Agenzia Regionale per lo Sviluppo e per i Servizi in Agricoltura, Servizio Agropedologia. Rubbettinopp 387
ARSSA (2005) Carta del rischio di erosione attuale e potenziale della regione Calabriascala 1:250000,Monografia divulgativa, ARSSA-Agenzia Regionale per lo Sviluppo e per i Servizi in Agricoltura,Servizio Agropedologia, Cerbone, Napoli 2005
Billi P, Dramis F (2003) Geomorphological investigation on gully erosion in the Rift Valley and thenorthern highlands of Ethiopia. Catena 50:353368
Nat Hazards (2011) 56:881898 895
123
Bull J, Kirkby MJ (2002) Channel heads and channel extension. In: Bull LJ, Kirkby MJ (eds) DrylandRivers: hydrology and geomorphology of semi-arid channels. Wiley, Chichester, pp 263298
Caloiero D, Mercuri T, Reali C (1990) Le precipitazioni in Calabria (19211980). Geodata 36 CNR IRPI,Cosenza
Carobene L, Mengani ME, Oliverio M (1989) Superfici terrazzate pleistoceniche nella media valle del fiumeCrati (Calabria). Il Quaternario 2:1539
Carrara A, Cardinali M, Detti R, Guzzetti F, Pasqui V, Reichenbach P (1991) GIS techniques and statisticalmodels in evaluating landslide hazard. Earth Surf Proc Land 16:427445
Carrara A, Cardinali M, Guzzetti F, Reichenbach P (1995) GIS technology in mapping landslide hazard. In:Carrara A, Guzzetti F (eds) Geographical information systems in assessing natural hazards. Kluwer,Dordrecht, pp 135175
Cevik E, Topal T (2003) GIS-based landslide susceptibility mapping for a problematic segment of thenatural gas pipeline, Hendek (Turkey). Environ Geol 44:949962
Chung CF, Fabbri AG (2003) Validation of spatial prediction models for landslide hazard mapping. NatHazards 30:451472
Colella A, De Boer PL, Nio SD (1987) Sedimentology of a marine intermontane Pleistocene Gilbert-typefan-delta complex in the Crati Basin, Calabria, southern Italy. Sedimentology 34:721736. doi:10.1111/j.1365-3091.1987.tb00798.x
Collison AJC (2001) The cycle of instability: stress release and fissure flow as controls on gully head retreat.Hydrol Process 15:312
Conforti M (2008) Studio geomorfopedologico dei processi erosivi nel bacino del T. Turbolo (Calabriasettentrionale) con il contributo della spettrometria della riflettenza. PhD thesis, University of Calabria,pp 310
Conoscenti C, Di Maggio C, Rotigliano E (2008) Soil erosion susceptibility assessment and validation usinga geostatistical multivariate approach: a test in Southern Sicily. Nat Hazards 46:287305
Dai FC, Lee CF, Li J, Xu ZW (2001) Assessment of landslide susceptibility on the natural terrain of LantauIsland, Hong Kong. Environ Geol 40:381391
Dramis F, Gentili B (1977) Contributo allo studio delle acclivita` dei versanti nellAppennino Umbro.Marchigiano. Stud Geol Camerti 3:153164
Federici PR, Puccinelli A, Cantarelli E, Casarosa N, DAmato Avanzi G, Falaschi F, Giannecchini R,Pochini A, Ribolini A, Bottai M, Salvati N, Testi C (2007) Multidisciplinary investigations in eval-uating landslide susceptibilityan example in the Serchio River valley (Italy). Quat Int 171172:5263
Gattinoni P (2008) Parametrical landslide modeling for the hydrogeological susceptibility assessment: fromthe Crati Valley to the Cavallerizzo landslide (Southern Italy). Nat Hazards 50:161178. doi:10.1007/s11069-008-9328-1
Guzzetti F, Carrara A, Cardinali M, Reichenbach P (1999) Landslide hazard evaluation: a review of currenttechniques and their application in a multi-scale study, Central Italy. Geomorphology 31:181216
Iovine G, Petrucci O, Rizzo V, Tansi C (2006) The March 7th 2005 Cavallerizzo (Cerzeto) landslide inCalabriaSouthern Italy. Engineering geology for tomorrows citiesthe 10th IAEG congress,Nottingham (UK), The Geological Society of London, Paper number 785
Jenks GF (1989) Geographic logic in line generalization. Cartographica 26(1):2742Kakembo V, Xanga WW, Rowntree K (2009) Topographic thresholds in gully development on the hill-
slopes of communal areas in Ngqushwa Local Municipality, Eastern Cape, South Africa. Geomor-phology 110:188195
Koppen W (1936) Das geographische System der Klimate. In: Koppen W, Geiger R, Teil C (eds) Handbuchder Klimatologie. Band 5. Gebruder Borntrager, Berlin, pp 146
Lanzafame G, Zuffa G (1976) Geologia e petrografia del foglio Bisignano (Bacino del Crati, Calabria).Geologica Romana 15:223270
Lee S (2004) Soil erosion assessment and its verification using the Universal Soil Loss Equation andgeographic information system: a case study at Boun, Korea. Environ Geol 45:457465
Magliulo P, Di Lisio A, Russo F, Zelano A (2008) Geomorphology and landslide susceptibility assessmentusing GIS and bivariate statistics: a case study in southern Italy. Nat Hazards 47:411435
Maharaj R (1993) Landslide processes and landslide susceptibility analysis from an upland watershed: acase study from St Andrew, Jamaica, West Indies. Eng Geol 34:5379
Martnez-Casasnovas JA, Anton-Fernandez C, Ramos MC (2003) Sediment production in large gullies ofthe Mediterranean area (NE Spain) from high-resolution digital elevation models and geographicalinformation systems analysis. Earth Surf Process Landf 28:443456. doi:10.1002/esp.451
Moore ID, Burch GJ (1986) Physical basis of the length-slope factor in the universal soil loss equation. SoilSci Soc Am J 50:12941298
896 Nat Hazards (2011) 56:881898
123
Moore ID, Grayson RB, Ladson AR (1991) Digital terrain modelling: a review of hydrological, geomor-phological, and biological applications. Hydrol Process 5:330
Moretti S, Rodolfi G (2000) A typical calanchi landscape on the Eastern Apennine margin (Atri, CentralItaly): geomorphological features and evolution. Catena 40:217228
Morgan RPC (2005) Soil Erosion and Conservation, 3rd edn. Wiley, New YorkNagarajan R, Roy A, Vinod Kumar R, Mukherjee A, Khire MV (2000) Landslide hazard suspectibility
mapping based on terrain and climatic factors for tropical monsoon regions. Bull Eng Geol Env58:275287
Ndomba Pm, Mtalo F, Killingtveit A (2009) Estimating gully erosion contribution to large catchment yieldrate in Tanzania. Phys Chem Earth 34:741748
Nefeslioglu HA, Duman TY, Durmaz S (2008) Landslide susceptibility mapping for a part of tectonic KelkitValley (Eastern Black Sea region of Turkey). Geomorphology 94:401418
Poesen J, Vandaele K, Van Wesemael B (1998) Gully erosion: importance and model implications. In:Boardman J, Favis-Mortlock D (eds) Modelling soil erosion by water, vol I 55. NATO ASI Series,Springer, Berlin Heidelberg, pp 285311
Poesen J, Vandekerckhove L, Nachtergaele J, Oostwoud Wijdenes D, Verstraeten G, Van Wesemael B(2002) Gully erosion in dryland environments. In: Bull LJ, Kirkby MJ (eds) Dryland Rivers: hydrologyand geomorphology of semi-arid channels. Wiley, Chichester, pp 229262
Pulice I, Scarciglia F, Leonardi L, Robustelli G, Conforti M, Cuscino M, Lupiano V, Critelli S (2009) Studiomultidisciplinare di forme e processi denudazionali nellarea di Vrica (Calabria orientale). Bollettinodella Societa` Geografica Italiana 87(III):399414
Rautela P, Lakhera RC (2000) Landslide risk analysis between Giri and Ton Rivers in Himalaya (India). IntJ Appl Earth Obs Geoinf 2:153160
Remondo J, Gonzalez A, Teran J, Cendrero A, Fabbri A, Chung C (2003) Validation of landslide sus-ceptibility maps; examples and applications from a case study in Northern Spain. Nat Hazards30:437449
Renard KG, Foster GR, Weesies GA, Mccool DK, Yoder DC (1997) Predicting soil erosion by water: aguide to conservation planning with the revised soil loss equation (RUSLE). US Dept. of Agriculture.Agric. Handbook No. 703, pp 404
Sorriso-Valvo M, Tansi C (1996) Relazioni tra frane, forme del rilievo e strutture tettoniche nella mediaValle del Fiume Crati (Calabria). Geografia Fisica e Dinamica Quaternaria 19:107117
Sorriso-Valvo M, Bryan RB, Yair A, Iovino F, Antronico L (1995) Impact of afforestation on hydrologicalresponse and sediment production in a small Calabrian catchment. Catena 25:89104
Su`zen ML, Doyuran V (2003) A comparison of the GIS based landslide susceptibility assessment methods:multivariate versus bivariate. Environ Geol 45:665679
Terranova O, Antronico L, Coscarelli R, Iaquinta P (2009) Soil erosion risk scenarios in the Mediterraneanenvironment using RUSLE and GIS: an application model for Calabria (southern Italy). Geomor-phology 112:228245
Tortorici L, Monaco C, Tansi C, Cocina O (1995) Recent and active tectonics in the Calabrian Arc (southItaly). Tectonophysics 243:3755
USDA (2006) Keys to soil taxonomy, USDA (United States Department of Agriculture), Soil Survey Staff,10th edit. Natural Resources Conservation Service, Washington DC, pp 333
Valentin C, Poesen J, Li Y (2005) Gully erosion: impacts, factors and control. Catena 63:132153. doi:10.1016/j.catena.2005.06.001
Van Westen CJ (1993) Application of geographic information systems to landslide hazard zonation. ITCpubl. no. 15, Int. Ins. for Aerospace and Earth Res. Surv, Enschede, The Netherlands, p 245
Van Westen CJ (1997) Statistical landslide hazard analysis. ILWIS 2.1 for Windows application guide. ITCpublication, Enschede, pp 7384
Vandekerckhove L, Poesen J, Oostwoudwijdenes DJ, Gyssels G, Beuselinck L, De Luna E (2000) Char-acteristics and controlling factors of bank gullies in two semi.arid Mediterranean environments.Geomorphology 33:3758
Vanwalleghem T, Poesen J, Nachtergaele J, Verstraeten G (2005) Characteristics, controlling factors andimportance of deep gullies under cropland on loess.derived soils. Geomorphology 69:7691
Wang HB, Sassa K (2005) Comparative evaluation of landslide susceptibility in Minamata area, Japan.Environ Geol 47:956966
Wilson JP, Gallant JC (2000) Terrain analysis principles and applications. Wiley, Toronto Canada, p 479Yalcin A (2008) GIS-based landslide susceptibility mapping using analytical hierarchy process and bivariate
statistics in Ardesen (Turkey): comparison of results and confirmations. Catena 2:112
Nat Hazards (2011) 56:881898 897
123
Yin KJ, Yan TZ (1988) Statistical prediction model for slope instability of metamorphosed rocks. In:Proceedings of the 5th international symposium on landslides, Lausanne, Switzerland, vol 2,pp 12691272
Zezere JL, Reis E, Garcia R, Oliveira S, Rodrigues ML, Vieira G, Ferreira AB (2004) Integration of spatialand temporal data for the definition of different landslide hazard scenarios in the area north of Lisbon(Portugal). Nat Haz Earth Sys Sci 4:133146
898 Nat Hazards (2011) 56:881898
123
Geomorphology and GIS analysis for mapping gully erosion susceptibility in the Turbolo stream catchment (Northern Calabria, Italy)AbstractIntroductionGeo-environmental setting of the study areaMaterials and methodsAnalysis of predisposing factorsLithologyLand useSlopeAspectPlan curvatureLength-slope factorStream power indexTopographical wetness index
Susceptibility analysis
Results and discussionGully erosion processesGully erosion susceptibility assessment
ConclusionsReferences
/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 149 /GrayImageMinResolutionPolicy /Warning /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 150 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 599 /MonoImageMinResolutionPolicy /Warning /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 600 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile (None) /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False
/CreateJDFFile false /Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure false /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles false /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /DocumentCMYK /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /UseDocumentProfile /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice