2
XXXXXXXXXXX YYYY-MM-DD XXX CODE CODE A b XXXXXXXXXXX XXX YYYY-MM-DD STEP 3 STEP 6 STEP 9 Get Ready Apply Sensor Prepare Sensor Applicator Clean site with alcohol wipe. Allow site to dry before proceeding. Peel lid completely off Sensor Pack. Unscrew cap from Sensor Applicator. CAUTION: Sensor codes must match on Sensor Pack and Sensor Applicator or glucose readings will be incorrect. Select site on back of upper arm. Do not use other sites as these are not approved and may result in inaccurate glucose readings. Note: Avoid scars, moles, stretch marks, lumps, and insulin injection sites. To prevent skin irritation, rotate sites between applications. Refer to your User’s Manual for full system instructions and information. Touchscreen Home Button USB Port Sensor Pack Reader Place Sensor Applicator over site and push down firmly to apply Sensor. CAUTION: Do not push down on Sensor Applicator until placed over prepared site to prevent unintended results or injury. Make sure Sensor is secure. Discard used Sensor Applicator and Sensor Pack according to local regulations. Gently pull Sensor Applicator away from your body. STEP 1 STEP 4 STEP 7 STEP 2 STEP 5 STEP 8 Line up dark mark on Sensor Applicator with dark mark on Sensor Pack. On a hard surface, press down firmly on Sensor Applicator until it comes to a stop. Sensor Applicator is ready to apply Sensor. CAUTION: Sensor Applicator now contains a needle. Do not touch inside Sensor Applicator or put it back into Sensor Pack. Lift Sensor Applicator out of Sensor Pack. Lid Cap Sensor Sensor Applicator Codes on labels must match 1 Assemble and Apply Sensor to the back of your upper arm 2 Start new Sensor with Reader Wait 60 minutes for start-up You can check your glucose whenever you want for up to 14 days FLASH GLUCOSE MONITORING SYSTEM Quick Start Guide for FreeStyle Libre 14 day Reader Setup Overview 1 Assemble and Apply Sensor to the back of your upper arm

Get Ready · 2020-01-31 · Note: Avoid scars, moles, stretch marks, lumps, and insulin injection sites. To prevent skin irritation, rotate sites between applications. Refer to your

  • Upload
    others

  • View
    1

  • Download
    0

Embed Size (px)

Citation preview

Page 1: Get Ready · 2020-01-31 · Note: Avoid scars, moles, stretch marks, lumps, and insulin injection sites. To prevent skin irritation, rotate sites between applications. Refer to your

XXXXXXXXXXX

YYYY-MM-DD

XXXCODE

CODE

Abbott Diabetes Care Inc. 1360 South Loop Road, Alameda, CA 94502 A

RT36504 R

ev. 1

08/1

5

XXXXXXXXXXX

XXX

YYYY-MM-DD

STEP 3

STEP 6

STEP 9

Get

Rea

dy

Ap

ply

Sen

sor

Pre

par

e Se

nso

r A

pp

lica

tor

Clean site with alcohol wipe. Allow site to dry before proceeding.

Peel lid completely off Sensor Pack. Unscrew cap from Sensor Applicator.

CAUTION: Sensor codes must match on Sensor Pack and Sensor Applicator or glucose readings will be incorrect.

Select site on back of upper arm.Do not use other sites as these are not approved and may result in inaccurate glucose readings.Note: Avoid scars, moles, stretch marks, lumps, and insulin injection sites. To prevent skin irritation, rotate sites between applications.

Refer to your User’s Manual for full system instructions and information.

Touchscreen

Home ButtonUSB Port

Sensor Pack

Reader

Place Sensor Applicator over site and push down firmly to apply Sensor.

CAUTION: Do not push down on Sensor Applicator until placed over prepared site to prevent unintended results or injury.

Make sure Sensor is secure. Discard used Sensor Applicator and Sensor Pack according to local regulations.

Gently pull Sensor Applicator away from your body.

STEP 1

STEP 4

STEP 7

STEP 2

STEP 5

STEP 8

Line up dark mark on Sensor Applicator with dark mark on Sensor Pack. On a hard surface, press down firmly on Sensor Applicator until it comes to a stop.

Sensor Applicator is ready to apply Sensor.

CAUTION: Sensor Applicator now contains a needle. Do not touch inside Sensor Applicator or put it back into Sensor Pack.

Lift Sensor Applicator out of Sensor Pack.

Lid Cap

Sensor

SensorApplicator

Codes on labels must match

● 1 Assemble and Apply Sensor to the back of your upper arm

● 2 Start new Sensor with Reader

Wait 60 minutes for start-up

You can check your glucose whenever you want for up to 14 days

FLASH GLUCOSE MONITORING SYSTEM

Quick Start Guide for FreeStyle Libre 14 day Reader

Setup Overview

● 1 Assemble and Apply Sensor to the back of your upper arm

Page 2: Get Ready · 2020-01-31 · Note: Avoid scars, moles, stretch marks, lumps, and insulin injection sites. To prevent skin irritation, rotate sites between applications. Refer to your

No Active Sensor

10:23pm

Start NewSensor

ReviewHistory

350

250

150

50

236 mgdL

6am 10am 2pm

Glucose Going High

Check Glucose

Scan Sensor to checkglucose.

10:23pm

CheckGlucose

ReviewHistory

Ends in 14 days

Daily Patterns

Time In Target

Low Glucose Events

Sensor Usage

Logbook

Daily Graph

Average Glucose

Review History

1 / 2

minutes

OKNew SensorStarting Up

60 Sensor can be used in:

350

250

150

50

350

250

150

50

82 mgdL

mg/dL

Food Note

TargetGlucose

Range

Rapid-ActingInsulin Note

CurrentGlucose

Time

MessageTouch for more information

Check Blood GlucoseWhen you see this

symbol, do a blood glucose test before making treatment

decisions

Add NotesTouch to add notes to glucose reading

Current GlucoseGlucose from your latest scan

Glucose Trend ArrowDirection your glucose is goingGlucose Graph

Graph of your current and stored glucose readingsArrow What it means

Glucose rising quickly

Glucose rising

Glucose changing slowly

Glucose falling

Glucose falling quickly

Glucose Going Low

2pm 6pm 10pm

2pm 6pm 10pm

Press Home Button to turn on Reader.Note: If using Reader for the first time, follow the prompts to set date, time, and target glucose range.

Touch Start New Sensor. Hold Reader within 1.5 inches (4 cm) of Sensor to scan it. Sensor can be used to check your glucose after 60 minutes.

Press Home Button to turn on Reader. Press Home Button again to go to Home Screen.

Touch Review History. Select option to view.

Hold Reader within 1.5 inches (4 cm) of Sensor to scan it.

Press Home Button to turn on Reader. Reader shows your glucose readings.

Understanding your glucose readings

If you have followed the instructions described in the User’s Manual and are still having difficulty setting up your System or if you are experiencing symptoms that are not consistent with your glucose monitoring, contact your health care professional.

STEP 3

STEP 3

STEP 3

STEP 1

STEP 1

STEP 1

STEP 2

STEP 2

STEP 2

Manufacturer

Consult instructions for use

WARNING: When you see the symbol, you must check your blood glucose with a blood glucose meter before making any treatment decisions. Sensor readings may not accurately reflect blood glucose levels.

FreeStyle, Libre, and related brand marks are trademarks of Abbott Diabetes Care Inc. in various jurisdictions. ©2018 Abbott ART39768-001 Rev. A 07/18

● 2 Start new Sensor with Reader

● 3 Check your glucose

● 4 Review your history