Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
Part No. 209371-ENovember 2003
4555 Great America ParkwaySanta Clara, CA 95054
Getting Started with Passport 4400 and 6400/7400 Interworking
2
Copyright © 2003 Nortel Networks
All rights reserved. November 2003.
Originated in Canada and the USA
The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this document is proprietary to Nortel Networks Inc.
The software described in this document is furnished under a license agreement and may be used only in accordance with the terms of that license. The software license agreement is included in this document.
Trademarks
Nortel Networks, the Nortel Networks logo, the Globemark, Unified Networks, Marathon, Passport, and Preside are trademarks of Nortel Networks.
Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated.
Ethernet is a trademark of Xerox Corporation.
Microsoft, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
Netscape and Netscape Navigator are registered trademarks of Netscape Communications Corporation
Pentium is a registered trademark of Intel Corporation.
SPARC and SPARCstation are trademarks or registered trademarks of Sparc International, Inc.
Java, Solaris, Sun, and Sun Microsystems are trademarks or registered trademarks of Sun Microsystems, Inc.
UNIX is a registered trademark of X/Open Company Limited.
All other trademarks and registered trademarks are the property of their respective owners.
The asterisk after a name denotes a trademarked item.
Restricted rights legend
Use, duplication, or disclosure by the United States Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS 252.227-7013.
Notwithstanding any other license agreement that may pertain to, or accompany the delivery of, this computer software, the rights of the United States Government regarding its use, reproduction, and disclosure are as set forth in the Commercial Computer Software-Restricted Rights clause at FAR 52.227-19.
Statement of conditions
In the interest of improving internal design, operational function, and/or reliability, Nortel Networks Inc. reserves the right to make changes to the products described in this document without notice.
Nortel Networks Inc. does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
Portions of the code in this software product may be Copyright © 1988, Regents of the University of California. All rights reserved. Redistribution and use in source and binary forms of such portions are permitted, provided that the above copyright notice and this paragraph are duplicated in all such forms and that any documentation, advertising materials, and other materials related to such distribution and use acknowledge that such portions of the software were developed
209371-E
3
by the University of California, Berkeley. The name of the University may not be used to endorse or promote products derived from such portions of the software without specific prior written permission.
SUCH PORTIONS OF THE SOFTWARE ARE PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
In addition, the program and information contained herein are licensed only pursuant to a license agreement that contains restrictions on use and disclosure (that may incorporate by reference certain limitations and notices imposed by third parties).
Nortel Networks Inc. software license agreement
This Software License Agreement (“License Agreement”) is between you, the end-user (“Customer”) and Nortel Networks Corporation and its subsidiaries and affiliates (“Nortel Networks”). PLEASE READ THE FOLLOWING CAREFULLY. YOU MUST ACCEPT THESE LICENSE TERMS IN ORDER TO DOWNLOAD AND/OR USE THE SOFTWARE. USE OF THE SOFTWARE CONSTITUTES YOUR ACCEPTANCE OF THIS LICENSE AGREEMENT. If you do not accept these terms and conditions, return the Software, unused and in the original shipping container, within 30 days of purchase to obtain a credit for the full purchase price.
“Software” is owned or licensed by Nortel Networks, its parent or one of its subsidiaries or affiliates, and is copyrighted and licensed, not sold. Software consists of machine-readable instructions, its components, data, audio-visual content (such as images, text, recordings or pictures) and related licensed materials including all whole or partial copies. Nortel Networks grants you a license to use the Software only in the country where you acquired the Software. You obtain no rights other than those granted to you under this License Agreement. You are responsible for the selection of the Software and for the installation of, use of, and results obtained from the Software.
1. Licensed Use of Software. Nortel Networks grants Customer a nonexclusive license to use a copy of the Software on only one machine at any one time or to the extent of the activation or authorized usage level, whichever is applicable. To the extent Software is furnished for use with designated hardware or Customer furnished equipment (“CFE”), Customer is granted a nonexclusive license to use Software only on such hardware or CFE, as applicable. Software contains trade secrets and Customer agrees to treat Software as confidential information using the same care and discretion Customer uses with its own similar information that it does not wish to disclose, publish or disseminate. Customer will ensure that anyone who uses the Software does so only in compliance with the terms of this Agreement. Customer shall not a) use, copy, modify, transfer or distribute the Software except as expressly authorized; b) reverse assemble, reverse compile, reverse engineer or otherwise translate the Software; c) create derivative works or modifications unless expressly authorized; or d) sublicense, rent or lease the Software. Licensors of intellectual property to Nortel Networks are beneficiaries of this provision. Upon termination or breach of the license by Customer or in the event designated hardware or CFE is no longer in use, Customer will promptly return the Software to Nortel Networks or certify its destruction. Nortel Networks may audit by remote polling or other reasonable means to determine Customer’s Software activation or usage levels. If suppliers of third party software included in Software require Nortel Networks to include additional or different terms, Customer agrees to abide by such terms provided by Nortel Networks with respect to such third party software.
2. Warranty. Except as may be otherwise expressly agreed to in writing between Nortel Networks and Customer, Software is provided “AS IS” without any warranties (conditions) of any kind. NORTEL NETWORKS DISCLAIMS ALL WARRANTIES (CONDITIONS) FOR THE SOFTWARE, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ANY WARRANTY OF NON-INFRINGEMENT. Nortel Networks is not obligated to provide support of any kind for the Software. Some jurisdictions do not allow exclusion of implied warranties, and, in such event, the above exclusions may not apply.
3. Limitation of Remedies. IN NO EVENT SHALL NORTEL NETWORKS OR ITS AGENTS OR SUPPLIERS BE LIABLE FOR ANY OF THE FOLLOWING: a) DAMAGES BASED ON ANY THIRD PARTY CLAIM; b) LOSS OF, OR DAMAGE TO, CUSTOMER’S RECORDS, FILES OR DATA; OR c) DIRECT, INDIRECT, SPECIAL, INCIDENTAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS),
Getting Started with Passport 4400 and 6400/7400 Interworking
4
WHETHER IN CONTRACT, TORT OR OTHERWISE (INCLUDING NEGLIGENCE) ARISING OUT OF YOUR USE OF THE SOFTWARE, EVEN IF NORTEL NETWORKS, ITS AGENTS OR SUPPLIERS HAVE BEEN ADVISED OF THEIR POSSIBILITY. The forgoing limitations of remedies also apply to any developer and/or supplier of the Software. Such developer and/or supplier is an intended beneficiary of this Section. Some jurisdictions do not allow these limitations or exclusions and, in such event, they may not apply.
4. General
a) If Customer is the United States Government, the following paragraph shall apply: All Nortel Networks Software available under this License Agreement is commercial computer software and commercial computer software documentation and, in the event Software is licensed for or on behalf of the United States Government, the respective rights to the software and software documentation are governed by Nortel Networks standard commercial license in accordance with U.S. Federal Regulations at 48 C.F.R. Sections 12.212 (for non-DoD entities) and 48 C.F.R. 227.7202 (for DoD entities).
b) Customer may terminate the license at any time. Nortel Networks may terminate the license if Customer fails to comply with the terms and conditions of this license. In either event, upon termination, Customer must either return the Software to Nortel Networks or certify its destruction.
c) Customer is responsible for payment of any taxes, including personal property taxes, resulting from Customer’s use of the Software. Customer agrees to comply with all applicable laws including all applicable export and import laws and regulations.
d) Neither party may bring an action, regardless of form, more than two years after the cause of the action arose.
e) The terms and conditions of this License Agreement form the complete and exclusive agreement between Customer and Nortel Networks.
f) This License Agreement is governed by the laws of the country in which Customer acquires the Software. If the Software is acquired in the United States, then this License Agreement is governed by the laws of the state of New York.
.
209371-E
5
Contents
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
How this Document is Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
When to Use this Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Passport 4400 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Passport 6400 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Passport 7400 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
How to get help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter 1Logging On to the Passport Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Logging On to the Passport 4400 CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Logging On to the Passport 6400/7400 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Chapter 2Configuring a PANL Over a Dedicated Line . . . . . . . . . . . . . . . . . . . . . . . . 15
Configuring the Passport 4400 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Configuring the Passport 6400/7400 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Verifying the PANL Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
On the Passport 4400 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
From the Passport 6400/7400 Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Troubleshooting the PANL Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
From the Passport 4400 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
From the Passport 6400/7400 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Getting Started with Passport 4400 and 6400/7400 Interworking
6 Contents
Chapter 3Configuring a PANL Tunneled Through a Public Frame Relay Network. . 21
Configuring the Passport 4400 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Configuring the Passport 6400/7400 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Verifying the PANL Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Troubleshooting the PANL Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Chapter 4Configuring a Network Management Connection to a Passport 4400 Unit27
Configuring the Passport 4400 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Configuring the Passport 6400/7400 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Adding the FRUNI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Adding the FRUNI DLCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Adding the FRDTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Adding the Virtual Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Adding the Ethernet* Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Adding the Passport 4400 Units to the IP Routing Table . . . . . . . . . . . . . . . . . . . . 33
Verifying the Network Management Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Chapter 5Configuring the RSI — RSA Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Configuring the RSI and RSAs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Verifying the RSI - RSA Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
209371-E
7
About This Guide
This document covers the basic provisioning needed to establish a Passport* Access Network Link (PANL) between a Passport 4400 unit and a Passport 6400/7400 unit.
Also included is a section on establishing a network management connection to the Passport 4400 unit, and a section on configuring the RSI-RSA components required for voice networking.
How this Document is Set Up
Each section includes an example configuration with typical variables. The commands that follow use the variables from the example. When you use the commands, replace the example variables with variables unique to your network setup.
Wherever possible, the examples and commands use and assume default values.
When to Use this Document
The provisioning discussed in this guide takes place after:
• You install the Passport 4400 unit’s expansion modules, install the Passport 4400 unit, and connect the cables.
• You install the Passport 6400/7400 unit’s cards, download the software, connect the cables, and have a network management station with access to the node.
Getting Started with Passport 4400 and 6400/7400 Interworking
8
Terminology
In the documentation, software, and MIBs for Passport 4400 and Passport 6400/7400 equipment, the terms PANL and MPANL are used interchangeably to refer to the Passport Access Network Link function. MPANL is the earlier term, but is still in common usage. MPANL is the term used within the Passport 6400/7400 command sets.
In this document, the term Passport 6400/7400 is used to refer interchangeably to either a Passport 6400 (all supported software versions) or a Passport 7400 (software version PCR4.2 and higher) system.
Related Documents
This document uses commands and information found in the Passport 4400 and Passport 6400/7400 suite of documents. For additional information, consult the following documents:
Passport 4400 Documentation
The following documents are part of the Passport 4400 document library:
• Getting Started with Passport 4400 and 6400/7400 Interworking (209371)
• Reference for Passport 4400 and 6400/7400 Interworking (209372)
• Reference for Passport 4400 Command Line Interface (CLI) (214371)
• Configuring and Operating the Passport 4400 (214372)
• Implementing QSIG on Passport 4460 (214280)
The Passport 4400 product documentation is delivered on the product CD and is also available from Nortel Networks* Web site (www.nortelnetworks.com).
Refer to the release notes (Passport 4400 Release Notes for Release x.x) for a complete list of available manuals for the product release you are using.
209371-E
9
Passport 6400 Documentation
• Passport 6400 Commands (241-6401-050)
• Passport 6400 Hardware Description (241-6401-200)
• Passport 6400 Preside Multiservice Data Manager Connectivity Guide (241-6401-275)
• Passport 6400 Security and Access Control Guide (241-6401-350)
• Passport 6400 Call Redirection Server Guide (241-6401-410)
• Passport 6400 Hunt Group Server Guide (241-6401-415)
• Passport 6400 Multiservice Passport Access Network Link Guide (241-6401-480)
• Passport 6400 Voice Networking Guide (241-6401-755)
• Passport 6400 Remote Server Agent Guide (241-6401-765)
• Passport 6400 Bridging Guide (241-6401-805)
• Passport 6400 Frame Relay DTE Access Guide (241-6401-810)
• Passport 6400 IP Routing Guide (241-6401-815)
• Passport 6400 IPX Routing Guide (241-6401-820)
• Passport 6400 Frame Relay UNI Guide (241-6401-900)
• Passport 6400 Frame Relay ISDN Switched Access Guide (241-6401-925)
• Passport 6400 Release Supplement
• Passport Networking Introduction (241-7501-310)
For a complete list and description of documentation in the Passport 6400 document library, see the Passport 6400 Documentation Guide (241-6401-001).
Passport 7400 Documentation
• Passport 7400, 15000, 20000 Commands (241-5701-050)
• Passport 7400 Hardware Description (241-7401-200)
• Passport 7400, 15000, 20000 Network Management Connectivity Guide (241-5701-271)
• Passport - MDM Network Security: Operations (NN10600-605)
• Passport - MDM Network Security: User Access Configuration (NN10600-606)
• Passport - MDM Network Security: Secure Communications Configuration (NN10600-607)
Getting Started with Passport 4400 and 6400/7400 Interworking
10
• Passport 7400, 15000, 20000 Call Redirection Server Guide (241-5701-410)
• Passport 7400, 15000, 20000 Hunt Group Server Guide (241-5701-415)
• Passport 7400 Multiservice Passport Access Network Link Guide (241-7401-480)
• Passport 7400 Voice Networking Guide (241-7401-755)
• Passport 7400 Remote Server Agent Guide (241-7401-765)
• Passport 7400, 15000, 20000 Frame Relay Fundamentals (241-5701-901)
• Passport 7400, 15000, 20000 Configuring Frame Relay (241-5701-902)
• Passport 7400, 15000, 20000 Understanding IP (241-5701-805)
• Passport 7400, 15000, 20000 Configuring IP (241-5701-810)
• Passport 7400, 15000, 20000 Frame Relay UNI Summary Card (241-5701-905)
• Passport 7400, 15000, 20000 Frame Relay Fundamentals (241-5701-901)
• Passport 7400, 15000, 20000 Configuring Frame Relay (241-5701-902)
• Passport 7400, 15000, 20000 Networking Overview (241-5701-400)
• Passport 7400, 15000, 20000 Overview (241-5701-030)
For a complete list and description of documentation in the Passport 7400 document library, see the Passport 7400, 15000, 20000 Documentation Guide (241-5701-001).
How to get help
If you purchased a service contract for your Nortel Networks* product from a distributor or authorized reseller, contact the technical support staff for that distributor or reseller for assistance.
If you purchased a Nortel Networks service program, contact one of the following Nortel Networks Technical Solutions Centers:
Technical Solutions Center Telephone
Europe, Middle East, and Africa +44 (0)20-8920-4618
North America (800) 4NORTEL or (800) 466-7835
209371-E
11
Additional information about the Nortel Networks Technical Solutions Centers is available from the www.nortelnetworks.com/help/contact/global URL.
An Express Routing Code (ERC) is available for many Nortel Networks products and services. When you use an ERC, your call is routed to a technical support person who specializes in supporting that product or service. To locate an ERC for your product or service, go to the http://www.nortelnetworks.com/help/contact/erc/index.html URL.
Asia Pacific +61 2 8870 8800
China (800) 810-5000
Technical Solutions Center Telephone
Getting Started with Passport 4400 and 6400/7400 Interworking
12
209371-E
13
Chapter 1Logging On to the Passport Units
Logging On to the Passport 4400 CLI
Use this procedure to connect a workstation to a Passport 4400 unit and log on to the Command Line Interface (CLI):
1 Connect the supplied cable from the serial port on your computer or terminal to the management port on the Passport 4400 unit.
2 Open a terminal emulation session with the following settings:
Data rate: 9600 bpsData bits: 8Stop bits: 1Parity: none
Press the [Enter] key once or twice. You will see the Login prompt.
3 Log on to the Command Line Interface (CLI):
Login: cliPassword:
Press the [Enter] key to the password prompt.
You will see a welcome message and the CLI> prompt.
Note: The CLI is one of three device management tools provided with the Passport 4400. The others are the Configurator and Install Tool. Refer to Using Passport 4400 Install Tool and Configuring and Operating Passport 4400 for more information.
Getting Started with Passport 4400 and 6400/7400 Interworking
14 Chapter 1 Logging On to the Passport Units
Logging On to the Passport 6400/7400 Unit
The usual practice is to deploy and set up Passport 6400/7400 units prior to deploying the Passport 4400 units. Thus, it is assumed that a network management workstation is already connected to either the Passport 6400/7400 unit locally, or is connected to the Passport network and can access the Passport 6400/7400 unit remotely.
209371-E
15
Chapter 2Configuring a PANL Over a Dedicated Line
Here is an example of PANL over a dedicated line:
The example shows the two Passport units as co-located for the sake of simplicity. However, a dedicated line to a remote Passport 4400 unit typically travels through a variety of facilities.
The commands that follow use the variables from the example. When you configure your PANL, replace the example variables with variables unique to your network setup.
Passport 4400
Passport 6400/7400
PANL(DCE)
lp/5 v35/1
Port 2 (DTE)
Dedicated line
Node name: MPA-1DNA Prefix: "302102100501"
Node name: PPNODE
Passport 4400
Getting Started with Passport 4400 and 6400/7400 Interworking
16 Chapter 2 Configuring a PANL Over a Dedicated Line
Configuring the Passport 4400 Unit
You must start with a defaulted Passport 4400 Unit:
CLI> reset system default reset
Then, log on to the CLI and continue with the defining the DNA prefix.
CLI> define msm profile dnaPrefix "302102100501"
You normally derive the DNA prefix from the link information. For example:
DNIC 3021RID 02MID 10Lp 05Port 01
CLI> set system administration nodeName "MPA_1"
You do not require a node name, but it is typically included. The node name appears within the prompt.
MPA_1> save configuration update
MPA_1> reset system current reset
Configuring the Passport 6400/7400 Unit
> start prov
PROV> add sw lpt/MPANL_DED
PROV> set sw lpt/MPANL_DED featureList mpaNetworkLink frameRelayUniPvcSvc frameRelayMmtc
PROV> check prov
PROV> act prov
209371-E
Chapter 2 Configuring a PANL Over a Dedicated Line 17
PROV> save prov
PROV> add sh card/5
PROV> set sh card/5 cardType v35
PROV> add lp/5
PROV> set lp/5 logicalProcessorType Sw Lpt/MPANL_DED
PROV> set lp/5 mainCard sh card/5
PROV> add lp/5 V35/1
PROV> set lp/5 v35/1 linkMode dce
PROV> set lp/5 v35/1 lineSpeed 64000
PROV> add mpanl/51
PROV> add mpanl/51 framer
PROV> set mpanl/51 framer int lp/5 v35/1
PROV> check prov
PROV> act prov
PROV> save prov
PROV> commit prov
PROV> end prov
Note: The Passport 6400/7400 unit needs to match the Passport 4400 unit’s line speed. This example uses the Passport 4400 unit’s default setting of 64 kbps.
Getting Started with Passport 4400 and 6400/7400 Interworking
18 Chapter 2 Configuring a PANL Over a Dedicated Line
Verifying the PANL Connection
Once the provisioning is complete on both the Passport 4400 unit and the Passport 6400/7400 unit, you should verify the link.
On the Passport 4400 Unit
From the Passport 4400 unit’s CLI, verify that the link is operational using the following command to list the link overview information:
MPA_1> show msm linkStatus table
IfIndex : 149InterfaceType : dteLAPFStatus : upLocalComponentName : "MPA_1 MPANL/149"RemoteComponentName : "PPNODE Mpanl/51 SigMpanl"RemoteGenCfgType : nortelAccessDevicePANLStatus : up
When the PANL is up, local and remote node names are displayed. The LAPF and PANL status display as up.
From the Passport 6400/7400 Workstation
From the Passport 6400/7400 workstation, verify that the link is operational using the following commands to display link information:
> d lp/5 v35/1
Unlocked and enabled.
> d mpanl/51 sig
Unlocked and enabled.
> d mpanl/51 framer
Unlocked and enabled.
209371-E
Chapter 2 Configuring a PANL Over a Dedicated Line 19
> d mpanl/51 sigm
Unlocked and enabled;dteComponentName - "MPA_1";CurrentState - informationTransfer.
> d mpanl/51 prefixDna/*
"302102100501"
Troubleshooting the PANL Connection
If your PANL fails to come up, check the following items:
From the Passport 4400 Unit
Check all cabling. Ensure that all cables are correct for the interface type and mode.
Check the WAN ports, using this command:
MPA_1> show wan parameters port operational table
Use the following commands to check the operational state of the PANL connection:
MPA_1> show wan statistics port table
Verify there are no link over runs or under runs, link errors, or bad packets.
MPA_1> show msm profile
Verify the prefix DNA is configured correctly.
MPA_1> show fr line user dlcmiPVC operational table
Verify LMI type is set to noLMIConfigured.
Getting Started with Passport 4400 and 6400/7400 Interworking
20 Chapter 2 Configuring a PANL Over a Dedicated Line
From the Passport 6400/7400 Unit
Check all cabling. Ensure all cables are correct for the interface type and mode.
Check the Passport patch panel connections.
Use the following commands to check the operational state of the PANL service:
> d lp/5 v35/1
Unlocked and enabled.
> d mpanl/51 sig
Unlocked and enabled.
> d mpanl/51 framer
Unlocked and enabled.Verify frames are being sent to/from the interface.
> d mpanl/51 sigm
Unlocked and enabled;dteComponentName - “MPA_1”;currentState - informationTransfer.
> d mpanl/51 prefixDna/*
Verify the 4400 PrefixDna is listed.
> d lp/5 v35/1
Verify line speed is set to “64000” b/s and the mode is set to DCE.
209371-E
21
Chapter 3Configuring a PANL Tunneled Through a Public Frame Relay Network
Here is an example of PANL tunneled through a public frame relay network. The commands that follow use the variables from this example. When you configure your PANL, replace the example variables with variables unique to your network setup.
Passport 4400
Passport 6400/7400
PANL/5117(DTE)
Public frame relay(DCE)
FRMUX/51
Node name: MPA_1DNA Prefix: "302102100501"Assigned DLCI by Public frame relay: 21
Node name: PPNODE
lp/5 v35/1
DLCI 17
Passport 4400
Getting Started with Passport 4400 and 6400/7400 Interworking
22 Chapter 3 Configuring a PANL Tunneled Through a Public Frame Relay Network
Configuring the Passport 4400 Unit
CLI> def msm profile dnaPrefix "302102100501"
You normally derive the DNA prefix from the link information. For example:
DNIC 3021RID 02MID 10Lp 05Port 01
CLI> set system administration nodeName "MPA_1"
You do not require a node name, but it is typically included. The node name appears within the prompt.
MPA_1> delete fr tunnel 149
MPA_1> add fr tunnel 149 21 base 2 dtepanl -1
The third party frame relay network supplies the DLCI number (of 21 in this case).
MPA_1> define fr line user dlcmipvc 155 ansi
The above command assumes an ANSI frame relay network.
MPA_1> save configuration update
MPA_1> reset system current reset
Configuring the Passport 6400/7400 Unit
> start prov
PROV> set sw lpt/MPANL_MUX featureList mpaNetworkLinkframeRelayMux frameRelayUni frameRelayMmtc
PROV> check prov
209371-E
Chapter 3 Configuring a PANL Tunneled Through a Public Frame Relay Network 23
PROV> act prov
PROV> save prov
PROV> add sh card/5
PROV> set sh card/5 cardType v35
PROV> add lp/5
PROV> set lp/5 logicalProcessorType Sw Lpt/MPANL_MUX
PROV> set lp/5 mainCard sh card/5
PROV> add lp/5 V35/1
PROV> set lp/5 v35/1 linkMode dce
PROV> set lp/5 v35/1 lineSpeed 64000
PROV> add frmux/51
PROV> set frmux/51 framer int lp/5 v35/1
PROV> set frmux/51 lmi procedures ansi
Assumes the third party frame relay network uses an ANSI LMI protocol.
PROV> add frmux/51 dlci/17
PROV> add mpanl/5117
PROV> add mpanl/5117 FrMuxSetup
Note: Line speed is the aggregate of all Passport 4400 units connected to this port. For example, if you add a second PANL with a line speed of 64000 to this port, the line speed in the command becomes 128000.
This example uses the Passport 4400 unit’s default value of 64 kbps. Normally, the line speed is negotiated with the third party network provider.
Getting Started with Passport 4400 and 6400/7400 Interworking
24 Chapter 3 Configuring a PANL Tunneled Through a Public Frame Relay Network
PROV> set mpanl/5117 FrMuxSetup PvcSetup dlciName frmux/51 dlci/17 ApplInfo
PROV> check prov
PROV> act prov
PROV> save prov
PROV> commit prov
PROV> end prov
Verifying the PANL Connection
Once the provisioning is complete on both the Passport 4400 unit and the Passport 6400/7400 unit, you should verify the link.
On the Passport 4400 Unit
MPA_1> show msm linkStatus table
IfIndex : 149InterfaceType : dteLAPFStatus : upLocalComponentName : "MPA_1 MPANL/149"RemoteComponentName : "PPNODE mpanl/5117 SigMpanl"RemoteGenCfgType : nortelAccessDevicePANLStatus : up
When the PANL is up, the local and remote node names are displayed. The LAPF and PANL status are displayed as up.
Note: Each additional instance of PANL to frmux/51 requires a separate DLCI, as provisioned in the above four commands.
209371-E
Chapter 3 Configuring a PANL Tunneled Through a Public Frame Relay Network 25
On the Passport 6400/7400 Unit
> d lp/5 v35/1
Unlocked and enabled.
> d frmux/51
Unlocked and enabled.
> d frmux/51 lmi
Unlocked and enabled;protocolStatus - normalCondition.
> d frmux/51 framer
Unlocked and enabled;no errors displayed;frames being sent to/from the interface.
> d frmux/51 dlci/17
Unlocked and enabled;usageState - busy;aBitStatusFromIf - active.
> d mpanl/5117 sig
Unlocked and enabled.
> d mpanl/5117 sigm
Unlocked and enabled,dteComponentName - "MPA_1",currentState - informationTransfer.
> d mpanl/5117 prefixDna/*
“302102100501”
Getting Started with Passport 4400 and 6400/7400 Interworking
26 Chapter 3 Configuring a PANL Tunneled Through a Public Frame Relay Network
Troubleshooting the PANL Connection
If your PANL does not come up:
On the Passport 4400 Unit
• Check all cabling. Ensure that all cables are correct for the interface type and mode.
• Ensure the connection to the third party frame relay network is correct.
• Ensure the LMI protocol is set to that of the frame relay network.
• Ensure that the DLCI matches that of the frame relay network.
• Enter the following CLI commands:
MPA_1> show wan statistics port table
Verify that there are no link over runs or under runs, link errors, or bad packets.
MPA_1> show msm profile
Verify that the prefix DNA is configured correctly.
MPA_1> >show fr tunnel operational table
Verify that the tunneling DLCI matches that of the frame relay network.
On the Passport 6400/7400 Unit
• Check all cabling. Ensure that all cables are correct for the interface type and mode.
• Check the Passport patch panel connections.
• Check the operational status of the framer:
> d mpanl/5117 framer
Unlocked and enabled; verify that frames are being sent to/from the interface.
209371-E
27
Chapter 4Configuring a Network Management Connection to a Passport 4400 Unit
This chapter describes how to enable network management connectivity between a network management system and the Passport 4400 units. Once the connection is made, you can open a telnet or NMS session to the Passport 4400 units for further provisioning and surveillance. The network management system can be located anywhere in the network.
The Passport 6400/7400 unit commands assume the network management core router (NMCR) is not yet set up. However, in a typical Passport network, the Passport 6400/7400 units are up and running prior to deploying the Passport 4400 units.
Note: You can use a single virtual FRUNI interface for multiple Passport 4400 units. However, each Passport 4400 unit requires its own SPVC connection to the network management core router (configured as an ILS virtual router).
This section assumes that each Passport 4400 unit has an active PANL into the Passport network.
Getting Started with Passport 4400 and 6400/7400 Interworking
28 Chapter 4 Configuring a Network Management Connection to a Passport 4400 Unit
Here is an example of a network management connection to a Passport 4400 unit:
The commands that follow use the variables in the example. When you configure your network management connection, replace the example variables with variables unique to your network setup.
Passport 4400
Passport4400
Subnet A
DNA Prefix: "30210111052"IfIndex 4 IP: 198.47.2.2Netmask: 255.255.255.0
FRUNI
VirtualRouter
FPFRDTE
LP/6FrUni DNA: "302101100699"
LP/76-Port Ethernet FP
Virtual hairpinconnection
Logical InterfaceIP: 198.47.2.1Netmask: 255.255.255.0
Ethernet PortIP: 198.47.100.1Netmask: 255.255.255.0
Network ManagementWorkstationIP: 198.47.100.2Netmask: 255.255.255.0
209371-E
Chapter 4 Configuring a Network Management Connection to a Passport 4400 Unit 29
Configuring the Passport 4400 Unit
CLI> define bridge global ipProtocol routed
CLI> add ip address entry 4 198.47.2.2 255.255.255.0 198.47.2.255
CLI> define ip base parameters dataLinkType 4 198.47.2.2 fr
CLI> define ip base parameters routeProtocolType 4 198.47.2.2 passiveRip
CLI> define ip base rip on
CLI> define ip invArp 4 ip enabled
CLI> add fr port spvcLANData 4 17 "302101100699" master
CLI> save configuration update
CLI> reset system current reset
CLI> add ip route 198.47.100.0 4 2 198.47.2.1 255.255.255.0
CLI> save configuration update
CLI> reset system current reset
Configuring the Passport 6400/7400 Unit
> start prov
PROV> add sw lpt/ENET
PROV> set sw lpt/ENET featureList ip
PROV> add sh card/7
PROV> set sh card/7 cardType 6pEth10BaseT
PROV> add lp/7
Getting Started with Passport 4400 and 6400/7400 Interworking
30 Chapter 4 Configuring a Network Management Connection to a Passport 4400 Unit
PROV> set lp/7 lpt sw lpt/ENET
PROV> set lp/7 mainCard sh card/7
PROV> add sw lpt/FRIP
PROV> set sw lpt/FRIP featureList frsVirtualFramer frameRelayUniPvcSvc frameRelayDte ip
PROV> add sh card/6
PROV> set sh card/6 cardType v35
PROV> add lp/6
PROV> set lp/6 lpt sw lpt/FRIP
PROV> set lp/6 mainCard sh card/6
PROV> ch prov
PROV> act prov
PROV> save prov
Adding the FRUNI
PROV> add fruni/699
PROV> set fruni/699 dna dataNetworkAddress 302101100699
PROV> delete fruni/699 framer
PROV> add fruni/699 vframer
PROV> set fruni/699 vframer logicalProcessor lp/6
Adding the FRUNI DLCI
PROV> add fruni/699 dlci/17
209371-E
Chapter 4 Configuring a Network Management Connection to a Passport 4400 Unit 31
The above command assigns a DLCI of 17 for network management traffic. Each Passport 4400 unit must have a unique DLCI.
PROV> set fruni/699 dlci/17 dc remoteDna 302101100501101
302101100501101 is the DNA prefix of the Passport 4400 unit with the 101 suffix added to indicate network management traffic. Refer to Configuring and Operating the Passport 4400 (2014372) for more information about the DNA prefix.
PROV> set fruni/699 dlci/17 dc remoteDlci 16
PROV> set fruni/699 dlci/17 dc type permanentSlave
Adding the FRDTE
PROV> add frdte/699
PROV> delete frdte/699 framer
PROV> add frdte/699 vframer
PROV> set frdte/699 vframer logicalProcessor lp/6
PROV> add frdte/699 staticDlci/17
The above command creates a static DLCI connection between the FRUNI service and the FRDTE. Each Passport 4400 unit in the network requires a unique DLCI.
PROV> set frdte/699 vframer otherVirtualFramer fruni/699 vframer
Adding the Virtual Router
PROV> add vr/1
Note: The remote DLCI is usually 16 for PANL.
Getting Started with Passport 4400 and 6400/7400 Interworking
32 Chapter 4 Configuring a Network Management Connection to a Passport 4400 Unit
PROV> add vr/1 ip
PROV> add vr/1 ip rip
PROV> add vr/1 pp/frdte699rg1
PROV> add vr/1 pp/frdte699rg1 ipp
PROV> set frdte/699 rg/1 linkToMedia vr/1 pp/frdte699rg1
rg/1 (remoteGroup) is created by default. Additional remote groups might need to be provisioned.
PROV> set frdte/699 rg/1 LinkToFrDteDlci frdte/699 stdlci/100
The above command links the static DLCI to the remote group containing the Passport 4400 units. This command must be repeated for each Passport 4400 unit connected to a Passport 6400/7400 unit.
PROV> add vr/1 pp/frdte699rg1 ipp logicalIf/198.47.2.1
PROV> set vr/1 pp/frdte699rg1 ipp logicalIf/198.47.2.1 broadcastAddress 198.47.1.255
PROV> set vr/1 pp/frdte699rg1 ipp logicalIf/198.47.2.1 netMask 255.255.255.0
PROV> add vr/1 pp/frdte699rg1 ipp logicalIf/198.47.2.1 rip
PROV> add vr/1 pp/ENET70
PROV> add vr/1 pp/ENET70 ipp
PROV> add vr/1 pp/ENET70 ipp logicalIf/198.47.100.1
PROV> set vr/1 pp/ENET70 ipp logicalIf/198.47.100.1 broadcastAddress 198.47.100.255
PROV> set vr/1 pp/ENET70 ipp logicalIf/198.47.100.1 netMask 255.255.255.0
PROV> add vr/1 pp/ENET70 ipp logicalIf/198.47.100.1 rip
209371-E
Chapter 4 Configuring a Network Management Connection to a Passport 4400 Unit 33
Adding the Ethernet* Port
PROV> add lp/7 enet/0
PROV> add lan/70
PROV> set lan/70 linkToProtocolPort vr/1 pp/ENET70
PROV> set lan/70 framer interfaceName lp/7 enet/0
PROV> check prov
PROV> act prov
PROV> save prov
PROV> commit prov
PROV> end prov
Adding the Passport 4400 Units to the IP Routing Table
Enter the following UNIX* command on the NMS or other workstation:
unix> route add -net 198.47.2.0 198.47.100.1
Verifying the Network Management Connection
Verify you have network management connectivity after configuring the connection.
On the Passport 4400 Unit
CLI> show ip route table
Note: You must be logged in to the UNIX workstation as root or super user to enter the above command.
Getting Started with Passport 4400 and 6400/7400 Interworking
34 Chapter 4 Configuring a Network Management Connection to a Passport 4400 Unit
The IP route table shows all the networks that the Passport 4400 unit can identify. Make sure that an entry for the static route is displayed. This entry should have Net Manager included in the information displayed about the static route.
CLI> ping <destination ip address>
The ping function allows you to confirm whether the connection to the specified IP address is up.
CLI> show fr port spvcLANData circuit table
The Port SPVC Circuit Table shows the SPVC if it is active to the Passport FRUNI.
On the Passport 6400/7400 Unit
> d vr/1 ip fwd/*
The above command shows all the networks that the Passport ILS can see. If RIP is disabled, your network management subnets may not show up here.
> d vr/1 ip rdb/*
The above command shows the routing database of the ILS. If RIP is disabled, your network management subnets may not show up here.
> ping -ip(<destination ip address>) vr/1 ip icmp
The above command will ping the specified address.
> d fruni/699 dlci/17
A-bit status active to/from interface indicates if the SPVC is up.
> d frdte/699 rg/1
Unlocked and enabled.
> d vr/1 pp/frdte60rg1 ipp
Unlocked and enabled.
209371-E
35
Chapter 5Configuring the RSI — RSA Connection
Voice networking requires the provisioning of the Remote Server Interface (RSI) on the Passport 4400 units and the Remote Server Agent (RSA) on the Passport 6400/7400 unit. Together they form the connection that allows Passport 4400 units to access the voice networking call server (VNCS) on the Passport 6400/7400 unit. Both digital and analog voice networking require an RSI - RSA connection.
Note the following when you configure the connection:
• A typical network has multiple RSAs for load sharing and backup purposes. The following example also uses this approach.
• You can locate the RSA on any Passport 6400/7400 unit in the network. However, the RSA and VNCS must be on the same Passport 6400/7400 shelf.
• The RSA should be configured on its own function processor.
• Regardless of the configured fax rate, all calls from the Passport 6400/7400 MVPs will have 13,000 b/s reserved bandwidth for the session.
• When you have voice or fax operating over the network and you perform a save function on the Passport 4400 unit (from the CLI, the Passport 4400 Configurator, or the Install Tool), there will be a momentary loss of voice or fax quality. The fax call might be disconnected.
Getting Started with Passport 4400 and 6400/7400 Interworking
36 Chapter 5 Configuring the RSI — RSA Connection
Here is an example of an RSI - RSA configuration:
The commands that follow use the variables from the example. When you configure your network, replace the example variables with variables unique to your network setup.
Configuring the RSI and RSAs
On the Passport 4400 Unit
CLI> set voice switchingProfile addServerSelect 1 vncs
CLI> add rsi server “[x121]302102100599” “Prim-RSA5” primary
CLI> add rsi server “[x121]302102110399” “Secon-RSA3” secondary
CLI> save configuration update
CLI> reset system cpu reset
Passport 6400/7400
Passport 6400/7400
Passport 4400DNA Prefix: "302102100201"
NetworkPANL
RSA
VNCS
RSA
VNCS
RSI
PANL lp/2 v35/1
Primary RSAlp/5RSA DNA: 302102100599
Secondary RSAlp/3RSA DNA: 302102110399
209371-E
Chapter 5 Configuring the RSI — RSA Connection 37
On the Passport 6400/7400 Unit Hosting the Primary RSA
PROV> add shelf card/5
PROV> set shelf card/5 cardType v35
PROV> add lp/5
PROV> set lp/5 mainCard sh card/5
PROV> add sw lpt/RSA
PROV> set sw lpt/RSA featureList serverAccessRsa
PROV> set sw lpt/CP featurelist vncsCallServer
PROV> set lp/5 logicalProcessorType sw lpt/RSA
PROV> check prov
PROV> act prov
PROV> save prov
PROV> add rsa/5
PROV> set rsa/5 logicalProcessor lp/5
PROV> set rsa/5 dna dataNetworkAddress 302102100599
PROV> add rsa/5 vncsAccess
PROV> check prov
PROV> act prov
PROV> save prov
Getting Started with Passport 4400 and 6400/7400 Interworking
38 Chapter 5 Configuring the RSI — RSA Connection
On the Passport 6400/7400 Unit Hosting the Secondary RSA
PROV> add shelf card/3
PROV> set shelf card/3 cardType v35
PROV> add lp/3
PROV> set lp/3 mainCard sh card/3
PROV> add sw lpt/RSA
PROV> set sw lpt/RSA featureList serverAccessRsa
PROV> set sw lpt/CP featurelist vncsCallServer
PROV> set lp/3 logicalProcessorType sw lpt/RSA
PROV> check prov
PROV> act prov
PROV> save prov
PROV> add rsa/3
PROV> set rsa/3 logicalProcessor lp/3
PROV> set rsa/3 dna dataNetworkAddress 302102110399
PROV> add rsa/3 vncsAccess
PROV> check prov
PROV> act prov
PROV> save prov
209371-E
Chapter 5 Configuring the RSI — RSA Connection 39
Verifying the RSI - RSA Connection
After both the RSI and RSA are configured, verify that the connection is up.
On the Passport 4400 Unit
CLI> show rsi server operational table
Verify that the “AvailStatus” shows available. This means the RSI server is available for address resolution.
On the Passport 6400/7400 Unit With the Primary RSA
> d rsa/5
Verify that the RSA is enabled.
> d rsa/5 VncsAccess
Unlocked and enabled.
> d rsa/5 Connection/*
Verify that the output displays remote RSI name.
On the Passport 6400/7400 Unit With the Secondary RSA
> d rsa/3
Verify that the RSA is enabled.
> d rsa/3 VncsAccess
Unlocked and enabled.
> d rsa/3 Connection/*
Verify that the output displays remote RSI name.
Getting Started with Passport 4400 and 6400/7400 Interworking
40 Chapter 5 Configuring the RSI — RSA Connection
209371-E
41
Index
CCLI, Passport 4400 13, 35
Configurator, Passport 4400 13, 35
Configuringnetwork management connection 27PANL over a dedicated line 15PANL tunneled through a frame relay
network 21RSI/RSA 36
core router 27
customer support 10
EEthernet Port 33
FFRDTE 31
FRUNI DLCI 30
IInstall Tool, Passport 4400 13, 35
IP Routing Table 33
LLine Speed 23
Log OnPassport 4400 Unit 13Passport 6400/7400 Unit 14
NNetwork Management 27
Network Management Core Router (NMCR) 27
PPANL
instances 24over a dedicated line 15troubleshooting the connection 26tunneled through a frame relay network 21verifying the connection 24
product support 10
RRSI/RSA 35
configuring 36verifying connection 39
Ssupport, Nortel Networks 10
Ttechnical support 10
VVirtual Router 31
Voice Networking Call Server (VNCS) 35
Getting Started with Passport 4400 and 6400/7400 Interworking
42 Index
209371-E
Getting Started with Passport 4400 and 6400/7400 Interworking
Address comments to:
Manager, Technical Publications
Nortel Networks
4555 Great America Parkway
Santa Clara, CA 95054 U.S.A.
U.S.A.
© 2003 Nortel Networks
All rights reserved
Information subject to change without notice
Publication: 209371-E
Date: November 2003