GLA UNIVERSITY, MATHURA (U.P.) INDIAgla.ac.in/public/uploads/filemanager/media/Syllabus_EN.pdf · MBA Open elective 3 1 0 4 4 PRACTICALS 6. EEE-481 Electric Drives Lab 0 0 2 1 2 7

Course Curriculum (w.e.f. Session 2015-16) B. Tech. (Electrical & Electronics Engineering)

DEPARTMENT OF ELECTRICAL ENGINEERING, Institute of Engineering &Technology

1

DEPARTMENT OF ELECTRICAL

ENGINEERING (SYLLABUS)

GLA UNIVERSITY,

MATHURA (U.P.) INDIA



2

Table of Contents

B.Tech. (EN) Course Structure ……………………………………………………………………………………………..………….i B.Tech. (EN) Syllabus ............................................................................................................... 1



3

COURSE STRUCTURE

B.TECH. (EN)


DEPARTMENT OF ELECTRICAL ENGINEERING, Institute of Engineering & Technology

4

First Semester

S. NO.

CODE SUBJECT TEACHINGSCHEME CREDITS CONTACTS HRS/WK L T P

1. AHM1101 Engineering Mathematics-I 3 1 0 4 4

2. AHP1001/ AHC1001

Engineering Physics/ Engineering Chemistry

3 1 0 4 4

3. CSE1001 Fundamentals of Computer and Programming

2 0 0 2 2

4. MEE1002/ MEE1001

Basic Mechanical Engineering/ Applied Mechanics

3 1 0 4 4

5. EEE1001/ ECE1001

Electrical Engineering/ Electronics Engineering

3 1 0 4 4

6. AHE1001 English Language Skills for Communication–I

2 0 0 2 2

PRACTICALS 7. AHE1081 English LanguageLab–I 0 0 2 1 2

8. MEE1082/ MEE1083

Engineering Workshop Practice Lab/Engineering Drawing

0 0 2 1 2

9. AHP1081/ AHC1081

Engineering Physics Lab/ Engineering Chemistry Lab

0 0 2 1 2

10. CSE1081 Computer Programming Lab -I 0 0 2 1 2

11. EEE1081/ MEE1081

Electrical and Electronics Lab/ Applied Mechanics Lab

0 0 2 1 2

12. ENE1099 General Proficiency 0 0 0 1 0

TOTAL 16 4 10 26 30

Second Semester

S.

NO

.

CODE SUBJECT TEACHINGSCHEME

CREDITS CONTACTS

HRS/WK L T P 1. AHM2101 EngineeringMathematics-II 3 1 0 4 4

2. AHC1001/ AHP1001

Engineering Chemistry/ Engineering Physics

3 1 0 4 4

3. CSE2001 Problem Solving using Computers 2 0 0 2 2

4. MEE1001/ MEE1002

Applied Mechanics/Basic Mechanical Engineering

3 1 0 4 4

5. ECE1001/ EEE1001

Electronics Engineering/ Electrical Engineering

3 1 0 4 4

6. AHE2001 English Language Skills for Communication–II

2 0 0 2 2

PRACTICALS 7. AHE2081 English Language Lab–II 0 0 2 1 2

8. MEE1083/

MEE1082

Engineering Drawing/ Engineering Workshop Practice Lab

0 0 2 1 2

9. AHC1081/ AHP1081

Engineering Chemistry Lab/ Engineering Physics Lab

0 0 2 1 2

10. CSE2081 Computer Programming Lab -II 0 0 2 1 2

11. MEE1081/ EEE1081

Applied Mechanics Lab/ Electrical and Electronics Lab

0 0 2 1 2


TOTAL 16 4 10 26

30



5

W.E.F. session 15-16

Third Semester

S. NO.

CODE SUBJECT TEACHING SCHEME

CREDITS CONTACTS

HR/WK L T P 1. AHM 3101 Mathematics – III 3 1 0 4 4 2. AHS 3001/

AHE 3001 Environmental studies/ Ethics & Values

2 0 0 2 2

3. EEE 3001 Electrical Circuit Theory 3 1 0 4 4

4. ENE3001 Electrical & Electronics Measurements & instruments

3 1 0 4 4

5. EEE 3002

Electrical & Electronics Engineering Materials 3 1 0 4

4

6. ECE 3002 Electromagnetic field theory 3 1 0 4 4 PRACTICALS

7. EEE 3081 Electric circuit lab 0 0 2 1 2

8. ENE 3081 Electrical & Electronics Measurement & instruments Lab

0 0 2 1 2

9. EEE 3082 Simulation Lab-I 0 0 2 1 2 10. AHE 3081 Soft Skills-I & Advances in C 0 0 2 1 2 11.

AHE3083 English for professional purposes (EPP-I) 0 0 4 2

4

12. ENE 3099 General Proficiency 0 0 0 1 0 TOTAL 17 05 12 29 34

Fourth Semester

S. NO.

CODE SUBJECT TEACHING SCHEME CREDITS

CONTACTS HR/WK

L T P

1. EEE 4001 Engineering circuit Analysis & Synthesis

3 1 0 4 4

2. AHE 3001/ AHS 3001

Ethics & values/ Environmental Studies

2 0 0 2 2

3. ENE4001 Analog Electronics 3 1 0 4 4

4. CSE 4070 Data Structures & Applications

3 0 0 3 3

5. EEE 4002 Electrical Machine-I 3 1 0 4 4 6. ECE 4002 Signals & Systems 3 1 0 4 4

PRACTICALS 7. CSE 4090 Data Structure Lab 0 0 2 1 2 8. EEE 4081 Simulation Lab-II 0 0 2 1 2 9 ENE 4081 Analog Electronics Lab 0 0 2 1 2

10. EEE 4082 Electrical Machine Lab-I 0 0 2 1 2 11. AHE 4081 Soft Skills-II 0 0 2 1 2 12.

AHE4083 English for professional purposes (EPP-II) 0 0 4 2

4

13. ENE4099 General Proficiency 0 0 0 1 0 TOTAL 17 04 14 29 35



6

W.E.F. session 2016-17

Fifth Semester

Sixth Semester

S.

NO. CODE SUBJECT TEACHING SCHEME CREDITS CONTACTS

HR/WK

L T P

1. CSE 6070 Essentials of

Information Technology 3 0 0 3 3

2. ENE 6001 Power Electronics 3 1 0 4 4

3. EEE 6003 Power System Analysis

& Protection 3 1 0 4 4

4. ECE 6071 Analog & Digital

Communication 3 1 0 4 4

5. ENE 6002 Microprocessors 3 1 0 4 4

PRACTICALS

6. ENE 6081 Power electronics Lab 0 0 2 1 2

7. EEE 6082 Power System &

Protection Lab 0 0 2 1 2

8. CSE 6090

Information Technology

Lab 0 0 2 1 2

9. AHE 6081 Soft Skills-IV 0 0 8 4 8

10. ENE 6082 Microprocessor Lab 0 0 2 1 2

11. ENE 6099 General Proficiency 0 0 0 1 0

TOTAL 15 4 16 28 35

S.

NO. CODE

SUBJECT TEACHING SCHEME CREDITS

CONTACTS

HR/WK

L T P

1. EEE5001 Electrical Machine-II 3 1 0 4 4

2. EEE5004 Elements of Power System 3 1 0 4 4

3. EEE5002 Control System 3 1 0 4 4

4. ENE5001 Digital Electronics 3 1 0 4 4

5. CSE5070 Object Oriented Programming 3 0 0 3 3

PRACTICALS

6. ENE5081 Digital electronics Lab 0 0 2 1 2

7. EEE5082 Control System Lab 0 0 2 1 2

8. EEE5081 Electrical Machine Lab-II 0 0 2 1 2

9. CSE5090 OOP Lab 0 0 2 1 2

10. AHE 5081 Soft Skills-III 0 0 8 4 8


TOTAL 15 4 16 28 35



7

Revised (Session 2016-17 only)

Seventh Semester

S. NO.

CODE SUBJECT TEACHING

SCHEME CREDITS CONTACTS

HR/WK L T P

1. EEE-401 Switchgear & Protection 3 1 0 4 4 2. EEE-402 Electric Drives 3 1 0 4 4 3. ECE-303, EEE-405-407 Professional Elective –I* 3 1 0 4 4 4. EEE-409, 411-412, 421 Professional Elective –II* 3 1 0 4 4

5. CSE-461-463, ECE-418,

MBA Open elective 3 1 0 4 4

PRACTICALS 6. EEE-481 Electric Drives Lab 0 0 2 1 2 7. EEE-489 Microprocessor Lab 0 0 2 1 2 9. EEE-482 Minor Project 0 0 6 3 6

10. EEE-483 Industrial Training 0 0 2 1 2 11. ENE-497 General Proficiency 0 0 0 1 0

TOTAL 15 5 12 27 32

Eighth Semester

S. NO.

CODE SUBJECT TEACHING

SCHEME CREDITS CONTACTS

HR/WK L T P

1. EEE-403 Electrical Instrumentation & Process Control

3 1 0 4 4

2. EEE-404 Power system Operation & Control

3 1 0 4 4

3. ECE-404, EEE-413,

415-416 Professional Elective –III* 3 1 0 4 4

4. ECE-403, EEE-417, 420,

461 Professional Elective –IV* 3 1 0 4 4

PRACTICALS

5. EEE484 Electrical Instrumentation Lab

0 0 2 1 2

6. EEE485 Project 0 0 14 7 14 7. ENE498 General Proficiency 0 0 0 1 0

TOTAL 12 4 16 25 32

NOTE: AT THE END OF SIXTH SEMESTER EACH STUDENT HAS TO UNDERGO AN INDUSTRIAL TRAINING PROGRAM OF MINIMUM FOUR WEEKS DURATION WHICH WILL BE EVALUATED AS EEE486 IN THE SEVENTH SEMESTER.

* ANY ONE SUBJECT TO BE OFFERED UNDER EACH PROFESSIONAL ELECTIVE.



8

PROFESSIONAL ELECTIVES B. TECH (EN)

ELECTIVE-I

S. TEACHING

CONTACT

CODE SUBJECT SCHEME CREDITS

NO.

HRS/WK

L T

P

1 ECE 303 Antenna & Wave Propagation 3 1 0 4 4

2 EEE 405 Digital Control System 3 1 0 4 4

3 EEE 406 Power System Dynamics & Stability 3 1 0 4 4

4 EEE 407 Digital Signal Processing 3 1 0 4 4

ELECTIVE-II

S.

TEACHING CONTACT


NO.

HRS/WK

L T

P

1 EEE 409 Advance Control System 3 1 0 4 4

2 EEE 411 Bio-medical Instrumentation 3 1 0 4 4

3 EEE 412 Smart Grid 3 1 0 4 4

4 EEE 421 Power Station Practice 3 1 0 4 4

ELECTIVE-III

S.

TEACHING CONTACT


NO.

HRS/WK

L T

P

1 ECE 404 Wireless Communication 3 1 0 4 4

2 EEE 413 Bio medical Signal Processing 3 1 0 4 4

3

EEE 415 Artificial intelligence & its

3

1

0

4

4

applications to power system

4 EEE416 Telemetry & Data Transmission 3 1 0 4 4

ELECTIVE-IV

S.

TEACHING CONTACT


NO.

HRS/WK

L T

P

1 ECE 403 Optical Communication & Networks 3 1 0 4 4

2 EEE 417 Industrial instrumentation 3 1 0 4 4

3 EEE 420 Energy Conservation & Management 3 1 0 4 4

4 EEE 461 Non Conventional Energy Resources 3 1 0 4 4

OPEN ELECTIVES FOR EN

S.

TEACHING CONTACT


NO.

HRS/WK

L

T

P

1 CSE 461 Human Computer Interaction 3 1 0 4 4

2 CSE 462 IT in Business 3 1 0 4 4

3 CSE 463 Soft Computing 3 1 0 4 4

4 ECE418 Digital image processing 3 1 0 4 4

5 MBA EDP 3 1 0 4 4



9

AHP 1001: ENGINEERING PHYSICS

W.E.F. ACADEMIC -YEAR 2016-17

OBJECT: The Syllabus is designed and styled especially to give B.Tech I year students a sound base in fundamental physics as well as to give their exposure to a wide range of

its utility in engineering and technology.

Module No.

Content Teaching Hours

I

Interference & Diffraction: Principle of superposition, Coherent Sources, Interference due to division of wave front- Biprism experiment and division of amplitude- Interference in thin films, Newton’s rings Expt; Diffraction of light, Fresnel and Fraunhoffer diffraction, Diffraction due to single slit and N-slits (Grating). Polarization: Concept of polarization of light, Phenomenon of double refraction, Superposition of ordinary and extra ordinary rays: Plane, Circularly and elliptically polarized light, quarter and half wave plates, Optical activity, Fresnel’s theory for optical rotation, Specific rotation, Biquartzpolarimeter.

20

II

Solid State Physics & Superconductivity: Bands in solids, band formation in solids,

Fermi level and Fermi energy, temperature dependence of conductivity in

semiconductors, Hall effect, Temperature dependence of resistivity in superconducting

materials, Meissner effect; Type I and Type II superconductors, Temperature

dependence of critical field, Applications of superconductors. Introduction of

nanoscience and nanotechnology with applications.

Electromagnetics & Dielectrics: Gauss law in electrostatics, Ampere’s law, Faraday law,

Maxwell’s equations (Integral and Differential forms), Equation of continuity,

Inconsistency in Ampere’s law: Displacement current, Propagation of E-M waves in free

space and in conducting media, Poynting theorem and Poynting vector, Dielectric

behavior of materials.

20

III

Relativistic Mechanics: Basic Concepts, Inertial & non-inertial frames, Galilean Transformations, Michelson- Morley experiment; Einstein’s postulates, Lorentz transformation equations; Length contraction, Time dilation, Addition of velocities, Variation of mass with velocity, Mass energy equivalence. Wave Mechanics & X-ray Diffraction: Wave - particle duality, de-Broglie hypothesis, Phase and group velocities: wave packet, Heisenberg’s uncertainty principle and its applications; Wave function and its normalization, Schrödinger’s wave equation: time dependent and time independent wave equations, Particle in one dimensional potential box; Bragg’s law, Compton’s effect.

20

Text Books: Engineering Physics by S.K. Gupta/ S.L. Gupta Vol. I & II

Reference Books: Optics - AjoyGhatak (TMH)

Fundamental of Physics - Resnick, Halliday& Walker (Wiley)

Concept of Modern Physics - by Beiser (Tata Mc-Graw Hill)

Materials Science and Engineering - by V. Raghavan (Prentice- Hall India)

Introduction to Electrodynamics by David J. Griffith (Prentice Hall of India)

Solid State Physics by S.O. Pillai (New Age International Publishers)

Credits: 04 L–T–P: 3–1–0 Semester I&II



10

Revised Syllabus of B.Tech I Year w.e.f. 2014-15

AHC 1001: ENGINEERING CHEMISTRY

Credits: 03 Semester I/II L-T-P : 3-1-0

Module No.


I

Chemical Kinetics: order and molecularity of reactions, zero order, First and second order reactions. Integrated rate equations. Theories of reaction rates, factors affecting rate of reaction. Chemical Bonding: M.O. theory and its applications in homo & hetero diatomic molecules. Hydrogen bond, metallic bond and their applications. Semi-conductor Reaction intermediates (carbocation, carbanion& free radical). Types of isomerism (optical and geometrical) chirality, elements of symmetry, diastereomers, optically active compounds, R-S configuration and E-Z geometrical isomers, conformation of ethane, n-butane. Functional materials: Photovoltaic cells, Biomaterials, Smart materials (Piezoelectric, pyroelectrics& ferroelectrics) and Advanced materials.

14

II

Introduction, Definition and Explanation of the terms: phase, component and degree of freedom, Application of phase rule to one component system (water & CO2 system), pH, buffer solution (Henderson equation). Polymers: Polymerization and its classification. Thermoplastic and Thermosetting resins. Properties of Polymers, Molecular weights of Polymers,Elastomers. Organic conducting and biodegradable polymers (PMMA, polystyrene, Teflon, neoprene, Buna-S, Buna-N Nylon 6, Nylon 66, Terylene, PLA, poly β hydroxy butyrate), vulcanization of rubber. Water Treatment: Introduction, Hardness and its units, , L-S Process, Calgon process, Zeolite and Ion-exchange resins, Treatment of Municipal Water, reverse Osmosis, Impurities in water, Characterstics of water, Treatment process Includes above deleted portions, boiler feed water, boiler troubles and remedial measures Lubrication: Introduction to lubrication, Classification, Properties & uses.

17

III

Corrosion: Introduction, Consequences, Types, Theories of Corrosion, (galvanic, pitting, stress, water line, intergranular& soil corrosion) and Protection of Corrosion. Spectroscopy: Elementary ideas and simple applications of UV, visible, infrared and NMR spectral techniques Fuels: Classification of fuels. Analysis of coal, determination of calorific values, Synthetic petrol Glass: Preparation, varieties & Uses. Ceramics: Introduction, classification, scope & application.

17

Text Book:

ShashiChawala“Theory and practical of engineering chemistry” 4th edition, DhanpatRai& Co. pvt ltd.

References:

Morrison & Boyd “Organic chemistry”,6th edition ,Pearson education

I.L. Finar “Organic chemistry”,5th edition, Longmans Green & Co ltd.

Y.R. Sharma “Elementary organic spectroscopy: principles and chemical application “1st edition, S.

Chand and Co.ltd.

S.S.Dara “Text book of engineering chemistry and pollution control” 2nd edition, S. Chand and Co.ltd.

Marsh G Fontana “Corrosion engineering” 3rd edition, Tata McGraw hill publishing Co ltd.

Attkins& Others “Inorganic chemistry”5th edition, Oxford university press.

Attkins& Others“Physical chemistry”6th edition, Oxford University press

Puri, Sharma and Pathania “Principles of physical chemistry” 44th edition, Vishal publishing Co Jalandhar.

K.J.Laidler“Chemical kinetics,” 3rd edition, Pearson education.



11

AHM-1101: ENGINEERING MATHEMATICS I Prerequisites: Differentiation, Integration, Algebra of matrices, Expansion of functions of onevariable,

Coordinate Geometry, Solution of I order and I degree ODE (variable separable, linear and homogeneous

forms).

Credits: 04 Semester I L–T–P: 3–1–0

Module Contents Teaching Hours

No. (Approx.)

Differential Calculus: Partial differentiation, Euler’s

theorem for homogeneous functions, Composite Functions,

I Total derivatives, Expansion of functions Of several 13

variables, Asymptotes and Curve Tracing (in Cartesian

coordinates), Jacobian and its properties, Extrema of

functions of several variables using Lagrange’s multipliers.

Matrices: Inverse by elementary transformations, rank of a

matrix, solution of system of linear equations, linear

II dependence and independence of vectors, complex 13

matrices, eigen values, eigen vectors. Cayley–Hamilton

theorem, Diagonalization, Reduction to Quadratic form,

rank, Index, signature; definite and semi - definite matrices.

Ordinary Differential Equations (ODEs):Introduction,

exact and reducible to exact differential equations, nth order

linear differential equations with constant coefficients, 14

III Euler-Cauchy Eqns., Simultaneous differential equations,

method of variation of parameters, Applications of II order

ODEs in engineering problems involving SHM, Electrical

circuits and Mechanical systems.

Learning Outcomes: After studying these topics, the student will be able to

Understand Partial differentiation and its applications Trace the curves given in cartesian coordinates Determine the linear dependence of functions Find the inverse of a square non singular matrix by various methods Solve the ordinary differential eqns. of higher order and grasp their applications

Text Books :

Jain, Iyengar and Jain: Advanced Engg. Mathematics, Narosa Publishing House, Delhi N. P. Bali & M. Goyal: A Text Book of Engg. Mathematics, Laxmi Publication, Delhi HariKishan: A Text Book of Matrices, Atlantic Publishers and Dist., Delhi

Reference Books:

G. B. Thomas & R. Finney: Calculus & Analytic Geometry (9th Ed. ) Addison Wesley

W. E. Boyce and R. Di Prima, Elementary Diff. Equations (8th Ed.), John Wiley

T. M. Apostol, Calculus, Volumes 1 and 2 , Wiley Eastern, 1980



12

EEE1001: ELECTRICAL ENGINEERING


Module Content

Teaching

No.

Hours

DC circuit analysis & Network theorems: Fundamentals of electric circuits,

Kirchhoff’s laws, mesh analysis, node analysis, Thevenin theorem, maximum

power transfer theorem, superposition theorem.

I Steady state AC analysis: AC fundamentals, average &rms values of different 13

AC waveforms, phasor algebra, analysis of series AC circuits, power triangle,

concept of power factor, power factor improvement.

Three phase AC circuits: Generation & advantages of three phase system, star

& delta connection, line & phase voltage/current relations.

Magnetic circuits: Faraday’s law,Self and mutual inductance, B-H

II Characteristics, hysteresis & eddy current losses, basics of magnetic circuit.

13

Single phase Transformers: : Constructional feature, Working Principle, EMF

equation, Ideal transformer, Equivalent Circuit, Phasor diagram , Definition of

voltage regulation and efficiency, Introduction to Auto-Transformer.

Rotating Electrical Machines:

Introduction to Electromechanical Energy Conversion. DC Machine:

Construction, Operating principle, Need of Starter, EMF Equation, Types of DC

Motor, Torque Equation, Characteristics and applications. Induction motor: 3-

phase: Construction & principle, Need of Starter, Torque Equation, Torque-slip

III Characteristics.

14

Single Phase Induction motor: Principle and Starting methods. Synchronous

Motor: Operating principle and applications.

Electrical Installation and Illumination: Introduction to distribution of

electrical energy, Types of cables & switches, Electrical wiring. Fluorescent

sodiumvapour and mercury lamp.

Text Books:

D.C. Kulshrestha, Electrical Enginerring, Tata McGraw Hill.

References: T.K. Nagsarkar&M.S.Sukhija, Basic Electrical Engineering, Edition 2008, Oxford University Press. H. Cotton, Advanced Electrical Technology,2nd Edition 2009, Wheeler Publishing. W.H. Hayt& J.E. Kennely,

Engineering Circuit Analysis, 7th Edition, McGraw Hill. S.N.Singh, Electrical power generation, transmission & distribution, Eastern Economy Edition. J. Nagarath, Basic Electrical Engineering, 2nd Edition, Tata McGraw Hill. D. E. Fitzgerald & A. Grabel Higginbotham, Basic Electrical Engineering, 5th Edition, McGraw Hill.

Edward Hughes, Electrical Technology, 3rd Edition, Pearson Education.



13

EEE1081: ELECTRICAL & ELECTRONICS LAB


Module Content Lab Hours

No.

To Verify the Thevenin’s Theorem (DC Circuits).

To Verify the Maximum Power Transfer Theorem (DC Circuits). Also

Draw Graph between Power and Load Resistance.

To Verify the Superposition Theorem (DC Circuits).

To Study the Phenomenon of Resonance in R-L-C Series Circuit and to

Draw Graph Between Frequency and Current. Also Show Half Power

Points.

To Determine the V-I Characteristics of A Semiconductor Diode. Also

Calculate Forward and Reverse Static and Dynamic Resistances.

I To Study the Half Wave and Full Wave (Center Tapped) Rectifier With 24

and Without Filter. Also to Calculate the Ripple Factor in Both Cases

(Without Filter).

To Study Single Phase (Induction Type) Energy Meter.

To Study Various Logic Gates Such As OR, AND, NOT, NAND, NOR.

Study of CRO and Measurement of Voltage and Frequency Using CRO.

V-I Characteristics of Zener Diode.

Identification of Active and Passive Components.

V-I Characteristics of Bipolar Junction Transistor in Common Base

Mode.



14

AHM-2101: ENGINEERING MATHEMATICS II Prerequisites: Differentiation, Definite Integrals, Coordinate Geometry, Vector Algebra, scalarand

vector products of two vectors, Expansion of a function in a series, A.P. and G. P.

Credits: 04 Semester II L–T–P: 3–1–0


No. (Approx.)

Convergence of Infinite Series: Introduction, Geometric

series test,nthterm test, Leibnitz test, Comparison test, p- 13

I test, Cauchy’s root test, Ratio test, Raabe’s test, Logarithmic

test, Cauchy condensation test, Special p - test, De Morgan

and Bertrand’s test, Special Logarithmic test.

Multiple Integrals: Beta and Gamma functions,Double and

II triple integrals, change of order of integration, Applications 13

to area and volume, change of variables, Dirichlet integral

and its Liouville extension.

Vector Calculus: Gradient, Divergence and curl, Vector

Identities, Line, surface and volume integrals, Work done by a

force, Green, Gauss' divergence and Stoke's theorem (without 14

III proof).

Fourier series: Fourier series of period 2 , Even and Odd

functions, Half range series, Change of interval.


Understand the concept of convergence and divergence.

Apply different tests for determining convergence of an infinite series.

Evaluate double, triple integrations and study their applications.

Analyze the Fourier series expansion of a discontinuous function.

Find integration and differentiation of vectors.

Text Books :

Jain, Iyengar& Jain: Advanced Engg. Mathematics, Narosa Publishing House, Delhi

M. Goyal& N. P. Bali: A Text Book of Engg. Maths, Laxmi Publications, Delhi HariKishan: Vector Algebra and Calculus, Atlantic Publishers & Dist., Delhi

HariKishan: Sure Success in Convergence, Atlantic Publishers & Dist., Delhi

Reference Books/ Text Books / Cases:

G. B. Thomas & R. Finney: Calculus & Analytic Geometry (9th Ed. ) Addison Wesley

T. M. Apostol, Calculus, Volumes 1 and 2 , Wiley Eastern, 1980

R. V. Churchill & J. W. Brown : Fourier series & boundary value problems (7th ed.), McGraw – Hill (2006).



15

AHM-3101: MATHEMATICS III Prerequisites: Differential and Integral Calculus, Ordinary Differential Equations, CoordinateGeometry,

Fourier series, Green’s theorem, Algebra of complex numbers.

Credits: 04 Semester III L–T–P : 3–1–0


No. (Approx.)

Partial Differential Equations (PDEs): Introduction, I order

Lagrange's linear PDEs, nthorder linear PDEs, Classification 13

I of II order PDEs, Method of separation of variables, One

dimensional wave equation, D’Alembert solution, One

dimensional heat flow equation.

Laplace Transforms: Properties of Laplace transform,

Laplace transform of derivatives and integrals, Unit step, 13

II Dirac - delta and periodic function, Properties of inverse

Laplace transform, convolution theorem, Application to

ordinary differential equations.

Complex Analysis:Analytic functions, C–R equations,

Harmonic Functions, Line integral in a complex plane,

Cauchy’s integral theorem and formula, Cauchy integral 14

III formula for derivatives, Taylor and Laurent series

(without proof), Singularities, Residue at a pole, Residue

theorem and its application in evaluation of real integrals

(excluding poles on the real axis).


Solve Partial Differential Equations of I and higher orders.

Apply Fourier series in applications of PDEs to wave and heat flow equations.

Know about the use of transforms in solving differential equations.

Understand the use of special function like unit step and dirac delta.

Grasp the concept of Analytic function and its applications in engineering.

Text Books :

Jain, Iyengar& Jain: Advanced Engg. Mathematics, Narosa Publishing House, Delhi

Manish Goyal and N. P. Bali: A Text Book of Engg. Maths, Laxmi Publications, Delhi

Reference Books/ Text Books / Cases:

R. V. Churchill and J. W. Brown, Complex variables and applications (7th Ed.), McGraw – Hill (2003).

J. M. Howie, Complex analysis, Springer –Verlag (2004)



16

AHE3001: ETHICS & VALUES

Credits: 02 Semester III L–T–P: 2–0–0

Module Content

Teaching

No.

Hours

Conceptual Foundations: Foundations of Morality; Professional Ethics;

Professional Standards in Engineering Practice; Major Theories of Ethics

and Different Ethical Approaches; Normatively of Science and Technology.

I Professions and Moral Dilemmas: Contemporary Ethical Issues; Conflict 14

of Interests; Contracts; Rights and Violations; Consent and Dissent;

Privacy and Confidentiality; Consultancy; Allocation of Burdens and

Benefits; Direct and Indirect Responsibility; Patents, Piracy and Clones.

Decision Making: Theoretical Bases; Foundational Values; Greater

II Welfare Approach; Risk-Benefit Analysis; Right-based Approach; Priority

14

Allocation; Binding Grounds of Decisions; Public Norms and Professional

Guidelines.

Social Responsibility: Individual and Collective Responsibility; Corporate

III Social Responsibility; Justice and Fairness; Beneficence and Safety; 11

Respect for Humanity, Life, and Nature; Sustainable Development.



17

EEE3002: ELECTRICAL & ELECTRONICS ENGINEERING MATERIALS

Credits: 04 Semester III L-T-P: 3-1-0

Module Content

Teaching

No.

Hours

A1: Crystal Structure of Materials:

Bonds in Solids, Crystal Structure, Co-Ordination Number, Atomic Packing

Factor, Miller Indices, Bragg’s Law and X-Ray Diffraction, Structural

I Imperfections, Crystal Growth.

14

Energy Bands in Solids, Classification of Materials Using Energy Band.

A2: Conductivity of Metals:

Thermal Conductivity of Metals, Heat Developed in Current Carrying

Conductors, Thermoelectric Effect.

B1: Properties:

Super Conductivity and Super Conducting Materials, Properties And

Applications of Electrical Conducting And Insulating Materials, Mechanical

Properties of Materials, Optical Properties of Solids.

II B2: Mechanism of Conduction in Semiconductor Materials:

14

Current Carriers in Semiconductors, Drift and Diffusion Currents,

Continuity Equation, Hall Effect.

B3: Semiconductor devices:

Miscellaneous Semiconductor Devices, Properties of Semiconductor

Materials.

C1: Dielectrics:

Polarization Mechanisms and Dielectric Constant, Behavior in Static and

Alternating Fields, Dielectric Loss, Piezoelectricity and Ferro electricity.

III C2: Magnetic Material:

14

Origin of Permanent Magnetic Dipoles in Matters, Classification

Diamagnetism, Para magnetism, Ferromagnetism, Ant ferromagnetism

and Ferrimagnetisms, Properties of Magnetic Materials, Soft and Hard

Magnetic Materials, Permanent Magnetic Materials, Magnetostriction.

Text Books:

T. K. Basak, “Electrical Engineering Materials”, New age International. References:

Solymar, “Electrical Properties of Materials” Oxford University Press.

Ian P. Hones, ” Material Science for Electrical and Electronic Engineering”, Oxford University Press.

TTTI Madras, “Electrical Engineering Materials”, TMH Education Pvt. Ltd.

Navneet Gupta, “Electrical & Electronic Engineering Materials”, DhanpatRai& Sons. A.J. Dekker,

“Electrical Engineering Materials” Prentice Hall of India

R.K. Rajput,” Electrical Engg. Materials,” Laxmi Publications.

C.S. Indulkar&S.Thiruvengadam, “An Introduction to Electrical Engg. Materials”, S.Chand& Co.



18

ECE3002: ELECTROMAGNETIC FIELD THEORY


Module Content

Teaching

No.

Hours

Review of Vector Algebra

Scalar & Vectors, Unit Vectors, Vector Addition & Subtraction, Position

Vector, Vector Multiplications, Components of Vector.

Coordinate System & Transformation

Cartesian, Cylindrical and Spherical Coordinates & Their Transformation.

I Vector Calculus 13

Line, Surface and Volume Integrals, Gradient of a Scalar, Divergence of a

Vector, Curl of a Vector, Divergence Theorem ,Stokes’s Theorem.

Electrostatics-I

Coulomb’s Law & Field Intensity, Electric Fields Due to Continuous Charge

Distributions. Electric Flux Density, Gauss’s law, Electric potential.

Electrostatics-II

Electric Dipole, Energy Density in Electrostatic Field, Conductors and

Current, Polarization in dielectrics, Continuity Equation and Relaxation

Time, Boundary Conditions, Poisson’s and Laplace’s Equation,

II Capacitance, Method of Images.

14

Magneto statics

Biot-savart’s law, Ampere’s Circuit law, Magnetic flux density, The scalar

and vector magnetic potential, Maxwell’s Equations for Static Field, Forces

due to Magnetic Field, Magnetic Torque and Moment, Magnetization in

Materials, Magnetic Boundary Conditions, Inductance, Magnetic Energy.

Maxwell’s Equations

Faraday’s law, Displacement Current, Maxwell’s Equations in Point and

Integral Forms, Retarded Potential

E M Wave Propagation

Wave Propagation in Lossy Dielectrics, Plane Wave in Lossless Dielectrics,

Plane Wave in Free Space, Plane Wave in Good Conductors, Power and the

III Poynting Vector, Reflection of a Plane Wave at Normal and Oblique

14

Incidence, Wave Polarization.

Transmission Lines

Transmission Line Parameters, Transmission Line Equation, Lossless and

Low Loss Propagation, Wave Reflection and VSWR, Transmission Line of

Finite Length,Reflection Coefficient, Standing Wave Ratio, Stub Matching,

Smith Chart and Measurement of Inductance, Capacitance and Resistance

With the Help of Smith Chart.

Text Book:

Jordan E.C. and Balmain K.G., “Electromagnetic wave and radiating Systems”, PHI Second edition.

W.H. Hayt and J.A. Buck, “Electromagnetic Field Theory”, 7th TMH. Reference Books:

M.N.O. Sadiku, “Elements of Electromagnetics”, 4th Ed, Oxford University Press Kraus, F “Electromagnetics” Tata McGraw Hill fifth edition.

Ramo S, Whinnery T.R. and Vanduzer T, “Field and Waves in communication electronics” John Wiley and sons third edition.



19

EEE-3001: Electrical Circuit Theory

Credits:04 Semester IV L-T-P:3-1-0

Module Content Teaching

Hours

I

Introduction: Review of KVL & KCL, Mesh Analysis with Super Mesh, Nodal Analysis With Super Node (Dependent Source), Star-Delta Transformation. Network Theorems (For AC Network):Thevenin's Theorem, Norton's Theorem, Maximum Power Transfer Theorem: Condition of Maximum Power under various loading conditions, Super Position Theorem, Substitution Theorem, Compensation Theorem, Reciprocity Theorem, Millman Theorem, Tellegen Theorem.

Transient AC Circuit Analysis: Initial conditions, Natural & Forced Responses of RL,

RC & RLC Networks to Different Inputs using classical Method.

14

II

Resonance in Series and Parallel Circuits: Phasor Diagram, Resonance Frequency, Variation of Different Quantities with Frequency, Quality Factor, Voltage/Current Magnification, Bandwidth of Resonant Circuit, Bandwidth in Terms of circuit Parameters, Relation Between Bandwidth, Resonant Frequency & Quality Factor. Sinusoidal Steady State Three Phase Circuit: Concept of phasor, AC power analysis, Analysis of Balanced & Unbalanced Three-Phase Circuits.

Symmetrical Components: Three-Phase Circuits with Unbalanced Sources &

Balanced Loads, Zero Sequence Component, Active Power in Sequence Components,

Three-Phase Circuits with Balanced Sources & Unbalanced Load.

14

III

The operational Amplifier as a Circuit Element: Introduction, Ideal Op Amp, Inverting Amplifier, Non-Inverting Amplifier, Summing Amplifier, Difference Amplifier, Cascaded Op-amp circuits Magnetically Coupled Circuits: Mutual Inductance, Coefficient of Mutual Inductance, Dot Convention, Combined mutual &self Inductance Voltage, Energy Considerations, Upper Limit of M, Coupling Coefficient, Linear Transformer, Ideal Transformer.

Network Topology: Concept of Network Graphs, Tree, Link, Cut Set Network Matrix,

Node Incidence Matrix, loop Incidence Matrix, Isomorphism, Cut Incidence Matrix &

relationship between them, Formulation of Network Equation, Duality.

14

Text Book:

D.RoyChoudhary, “Networks and Systems” 2nd Ed., New Age International (P) Ltd. Publishers. References:

M.E. Van Valkenburg, “An Introduction to Modern Network Synthesis”, Wiley Eastern Ltd.

Sudhakar, “Circuits & Networks: Analysis and Synthesis”, TMH Education Pvt. Ltd.

K.S. Suresh Kumar, “Electric Circuits and Networks” Pearson Education.

C.L Wadhwa, “Network Analysis and Synthesis (Including Linear System Analysis)” 3rd Ed., New Age International Publishers.

A.Chakrabarti, “Network Analysis & Synthesis”, DhanpatRai& Co



20

ENE-3001: ELECTRICAL AND ELECTRONICS MEASUREMENTS & INSTRUMENTS

Credits: 04 Semester III L-T-P: 3-1-0

Module Content Teaching Hour

I

Philosophy of Measurement: Methods of Measurement, Measurement System and Classification of Instrument, Characteristics of Instruments & Measurement System, Errors in Measurement & Its Analysis, Standards. Measurement of Current, Voltage and Power: Classification of Analog instruments. Principle of operation, construction, sources of error and compensations in PMMC – Moving iron – Dynamometer and induction type instruments. Extension of ranges and calibration of ammeters & voltmeters. Electrodynamics wattmeter – Theory, errors and compensation.

14

II

Instrument Transformers: Instrument Transformers and Applications in the Extension of Instrument Range Measurement of Circuit Parameters: Different Methods of Measuring Low, Medium and High Resistances, Measurement of Inductance, Capacitance& Frequency With The Help of AC Bridges. Potentiometer. Magnetic Measurement: Ballistic Galvanometer, Flux Meter, Determination of Hysteresis Loop, Determination of Iron Losses

14

III

Sensors and Transducers: Introduction to Sensors &Transducers: Resistive, Inductive and Capacitive Transducers Digital Measurement: Concept of Digital Measurement, Block Diagram Study of Digital Voltmeter, Frequency Meter, Power Analyzer and Harmonics Analyzer; Digital Multi meter Cathode Ray Oscilloscope: Basic CRO Circuit (Block Diagram), Cathode Ray Tube (CRT) & Its Components, Application of CRO in Measurement, Lissajous Pattern

13

Text Books: G.K. Banerjee, Electrical Measurement & Measuring Instruments, New Age International. A.K. Sawhney, “A Course in Electrical & Electronic Measurements & Instrumentation”, DhanpatRai&Sons

India. References: Forest K. Harris, “Electrical Measurement”, Willey Eastern Pvt. Ltd. India. M.B. Stout, “Basic Electrical Measurement” Prentice hall of India, India. Helfrick and Cooper, “Modern Electronic Instrumentation & Measurement Techniques”, PHI Learning. RajendraPrashad, “Electrical Measurement &Measuring Instrument”, Khanna Publisher. J.B. Gupta, “Electrical Measurements and Measuring Instruments”, S.K. Kataria& Sons. MMS Anand, “Electronic Instruments and Instrumentation Technology”, PHI Learning.



21

EEE 3081: ELECTRIC CIRCUIT LAB

Credits: 01 Semester III L-T-P:0-0-2

Module No.


I

1. Verification of Principle of Superposition with DC and AC Sources.

2. Verification of Thevenin, Norton and Maximum Power Transfer Theorems in ac Circuits.

3. Verification of Tellegen’s Theorem for Two Networks of the Same

Topology.

4. Determination of Transient Response of Current in RL and RC Circuits with Step Voltage Input.

5. Determination of Transient Response of Current in RLC Circuit with Step

Voltage Input for Under damped, Critically Damped and Over damped Cases.

6. Determination of Frequency Response of Current in RLC Circuit with

Sinusoidal AC Input.

7. Determination of z and h Parameters (dc only) for a Network and Computation of Y and ABCD Parameters.

8. Determination of Driving Point and Transfer Functions of a Two Port

Ladder Network and Verification with Theoretical Values.

9. Determination of Frequency Response of a Twin – T notch Filter.

10. Determination of Attenuation Characteristics of a Low Pass / High Pass Active Filters.

24



22

ENE3081: ELECTRICAL & ELECTRONICS MEASURMENT & INSTRUMENTS LAB


Module No.

Content Teaching

Hours

I,II,III

1. Measurement of low resistance by using Kelvin double bridge. 2. Measurement of self-inductance using Anderson Bridge. 3. Study of the Schering Bridge and to find capacitance of the capacitor

with the help of Schering Bridge. 4. Study of Hay’s bridge and to find self-inductance of the given inductor

with the help of hay’s bridge. 5. Study of a De-Sauty bridge & to compare the capacitance of Two

capacitors with the help of De-Sauty Bridge 6. To measure the form factor of rectified sine wave and calculation of

error. 7. Measurement of weight by using Load cell. 8. Instrument Transformer (CT &PT). 9. To draw the characteristics of the given LVDT. 10. To study the operation of a LDR and draw its V-I characteristics. 11. Measurement of Level by using Capacitive Transducer.

Measurement of phase difference and frequency using CRO (lissajous figure).

22



23

EEE3082: SIMULATION LAB-I

Credits:01 Semester III L-T-P:0-0-2

Module No.

Content Teaching

Hours

I

1. To Determine Node Voltages and Branch Currents in a Resistive Network

2. To obtain Thevenin’s Equivalent Circuit of a Resistive Network. 3. To Obtain Transient Response of a Series / Parallel R-L-C Circuit for

Step Input and Pulse Input. 4. To Obtain Frequency Response of a Series R-L-C Circuit for

Sinusoidal Voltage input. 5. Verification of Low Pass and High Pass Filter. 6. To Obtain Transient Response of Output Voltage in a Single Phase

Half Wave rectifier Circuit Using Capacitance Filter 7. To Obtain Output Characteristics of CE NPN Transistor 8. To Obtain Frequency Response of a R-C Coupled CE Amplifier 9. To Verify Truth Tables of NOT, AND or OR Gates Implemented by

NAND gates by Plotting Their Digital Input and Output Signals. 10. To Determine Line and Load Currents in a Three Phase Delta Circuit

Connected to a 3-phase balanced ac Supply. 11. To calculate the Total Harmonic Distortion (THD) in a Voltage Control

Amplifier.

24

References:

1. M.H. Rashid, “SPICE for Circuits and Electronics Using SPICE” Prentice Hall of India, 2000.

2. Paul W. Tuinenga, “SPICE: A guide to circuit Simulation and Analysis Using PSPICE”, Prentice Hall,

1992.



24

AHE 281/3081: SOFT SKILLS-I & ADVANCES IN C

Credits: 01 Semester III L–T–P: 0–0–2 After Two Courses on Spoken English Namely Spoken English 1 & 2, This Course Focuses more on the use of English, Specifically in Business Situations. The Course is based on Diverse Range of Business Themes Which Help Students Visualize the Expectations from a Professional. Course Objective: Soft Skills-I Programme will ensure that the Students Gain Confidence and Belief in What They are Doing and Do Not Overly Doubt Themselves. Being Aware of Learning What They Need Both in and Out of the Classroom, They Will Acquire Clarity on what is expected from them.


No.

Who am I and why Am I Here, Change is The Only Constant, Learning to

I Learn, Technology know-how for a Fresher, Knowledge on Tools, 10

Application Orientation, Career Management (Journey and options).

Business Communication, Service Mindset, Customer Mindset, Myths

II about Business, Values in Business, Business Etiquette, Email Etiquette, 10

Telephone Etiquette, Team Building, Role of a Manager.

III Attitude for Success, Role Models, Handling Peer Competition, Building

10

Relationships, Branding Yourself.

References:

Cook, S. “The Effective Manager”(E-book).IT Governance Publishing. Lesikar, R. V., & Pettit J. B. “Business Communication: Theory and Application”. New Delhi: All India

Traveller Book Seller. Bhatnagar, Nitin&MamtaBhatnagar, “Effective Communication and Soft Skills: Strategies forSuccess”.

New Delhi, Pearson (Dorling Kindersley, India Ltd.). Mohan, Krishan& NP Singh, Speaking English Effectively, New Delhi: Macmillan Publishers India Ltd. Pillalamarri, J. K. “Management of Soft Skills” Chennai: SciTech Publications. Rao, M.S. &Ramana, P.S.V., “Soft Skills for Better Employability”.ICFAI University Press.



25

AHS3001: ENVIRONMENTAL STUDIES

Credits: 02 Semester IV

L–T–P: 2–0–0

Module Content

Teaching

No. Hours

Basics Of Environmental Studies:

Environmental Studies: Introduction, Scope and Importance Environment:

I Concept, Natural and Anthropogenic Environment Natural Environment:

7

Structure & Function of Atmosphere, Hydrosphere, Lithosphere and

Biosphere Ecology and Ecosystem: Definitions Types, Structure & Functions of

Ecosystem.

Natural Resources:

Natural Resources: Introduction, Classification, Concept of Conservation

Present Status and Major Issues Related to Water Resources, Forest

II Resources and Mineral Resources Energy Resources: Introduction, 6

Classification, Energy Use Patterns, Energy Crisis, Alternative Energy

Resources Present Status and Major Issues Related to Fossil Fuels,

Hydroelectricity, Nuclear Energy, Solar Energy and Biomass Energy.

Current Environmental Problems:

Effects of Human Activities on Environment: Effect of Agriculture, Housing,

Mining, Transportation and Industries Environment Pollution: Causes, Effects

III and Control of Air Pollution, Water Pollution, Land Pollution and Noise

7

Pollution Introduction and Management of Solid Wastes and Hazardous

Wastes Global Environmental Challenges: Global Warming, Ozone Layer

Depletion, Acid Rain, Urbanization, Overpopulation and Biodiversity

Depletion.

Environmental Protection:

Environmental Protection: Role of Citizens, Role of Government, Initiatives by

NGOs, Contribution of International Agencies and Conventions Approaches to

IV Environmental Protection: Public Awareness, Environmental Education,

6

Environmental Ethics, Environmental Laws and Environmental Economics

Tools and Strategies: Environmental Impact Assessment, Life Cycle

Assessment, Ecological Footprints and Sustainable Development Efforts

towards Environmental Protection in India.

References:

Benny Joseph, Environmental Studies.

Deswal&Deshwal, Textbook on Environmental Studies.

AK De, Environmental Studies.

Shashi K Singh and AnishaSingh, Environmental Science & Ecology.

AgarwalandSangal, Environment & Ecology.



26

ECE4002: SIGNALS AND SYSTEMS

Module No.

Content Teaching

Hours

I

Signals: Definition, types of signals and their representations, commonly used signals (in continuous-time as well as in discrete-time), operations on continuous-time and discrete-time signals (including transformations of independent variables). Systems: Classification, linearity, time-invariance and causality, impulse response, characterization of linear time-invariant (LTI) systems, unit sample response, convolution summation, step response of discrete time systems, stability. convolution integral, co-relations, signal energy and energy spectral density, signal power and power spectral density, properties of power spectral density.

13

II

Fourier series Trigonometric & Exponential Fourier Series Analysis, Sampling Theorem, Nyquist criteria for sampling theorem Fourier Transforms (FT): (i) Definition, conditions of existence of FT, properties, magnitude and phase spectra, Some important FT theorems, Parseval’s theorem, Inverse FT, relation between LT and FT (ii) Discrete time Fourier transform (DTFT), inverse DTFT, convergence, properties and theorems, Comparison between continuous time FT and DTFT.

13

III

Laplace-Transform (LT) and Z-transform (ZT): (i) One-sided LT of some common signals, important theorems and properties of LT, inverse LT, solutions of differential equations using LT, Bilateral LT, Regions of convergence (ROC) (ii) One sided and Bilateral Z-transforms, ZT of some common signals, ROC, Properties and theorems, solution of difference equations using one-sided ZT, s- to z-plane mapping Application of Signals and Systems in MATLAB.

13

Text Book:

P. Ramakrishna Rao, “Signal and Systems” 2008 Edn., Tata MGH, New Delhi Reference Books:

Chi-Tsong Chen, “Signals and Systems”, 3rd

Edition, Oxford University Press, 2004 V.Oppenheim, A.S. Willsky and S. Hamid Nawab, “Signals & System”, PEARSON Education, Second

Edition, 2003.

Credits: 04 L–T–P: 3–1–0 Semester IV



27

EEE4001: ENGINEERING CIRCUIT ANALYSIS & SYNTHESIS

Credit: 04 Semester IV L-T-P:3-1-0

Module Content No. of

Lecture

I

Two -Port Network & their Characterization: Open Circuit, Short Circuit, Hybrid, Transmission & g-parameters, Relationship between Two Port Parameters, Lattice and Ladder Network, Series, Parallel & Cascade Connections of two Port Networks, Multi Networks, Multi Terminal Networks, Indefinite Admittance Matrix & its Properties, Gyrator, Anti Gyrator, Transformer & Transistor as Two Port elements. Complex frequency: Complex Frequency, General Form, DC Case, Exponential case, Sinusoidal Case, Exponentially damped Sinusoidal case, Relation of s to Reality, Damped Sinusoidal Forcing function.

14

II

Frequency response: The complex frequency plane,Natural response & the s plane,synthesizing the voltage ratio,Frequency& magnitude scaling,Bode diagrams Network Function: Driving Point Admittance Function & Transfer Functions of the Network & their Properties. Time Domain Analysis: Poles & Zeros of Network Functions, Physical Significance of Pole &Zero,Stability of a system based on Impulse Function & Impulse Response of a Network, Effect of Pole Position on Stability

14

III

Network Synthesis: Hurwitz's Polynomial & its Properties, Positive Real function & its Properties, Tests for Positive Real function, Synthesis of Driving Point Functions of LC, RC & RL Networks, Foster &Cauer forms. Filters: Introduction to Passive Filters, Image Parameters & characteristic Impedance, Constant K-Filter & m-Derived Filters, Low, High, Band pass, All Pass Filters along with their mathematical analysis.

13

References:

D. Roy Chaudhary, "Netwoks and Systems", 2nd Ed., New Age International

William H. Hayt, "Engineering Circuit Analysis", 8th Ed., McGraw Hill

A. Charkrabarti, "Circuit Theory", 6th Ed., DhanpatRai& Sons

M.E. Valkenburg, "Networl Analysis", 3rd Ed, Prentice Hall of India



28

EEE 4002: ELECTRICAL MACHINE - I

Credits: 04 Semester IV L-T-P: 3-1-0

Module Content

Teaching

No.

Hours

Single phase Transformers:

Brief Review of Single Phase Transformer, Polarity Test, Sumpner’s Test,

Single Phase and 3-Phase Autotransformers.

3 Phase Transformer:

I Phasor Groups, Parallel Operation of Single and 3-Phase Transformers, Zig

14

Zag Connections, 3-Phase To 2-Phase and 6-Phase Conversions, Harmonics

and Excitation Phenomena in 3-Phase Transformers-Effect of Connections

and Construction on Harmonics.

Special purpose Transformers:

Earthing Transformer, Pulse transformer, High frequency Transformer.

Energy Conversion Principle:

Magnetic Field Energy and Co-Energy, Coupling-Field Reaction For Energy

Conversion, Mechanical Work, Mechanical Forces and Torques in Singly and

Doubly-Excited Systems. Concepts of Reluctance and Electromagnetic

II Torques. Singly Excited Electric –Field Systems. 14

General concepts of Rotating Electrical Machines:

Magnetic and Electric Circuits in Rotating Electrical Machines, Winding

Coefficients, MMF of Distributed Windings. Torque in Terms of Flux and MMF

in Wound-Rotor Machines.

DC Machines:

Concept of Simplex Lap and Wave Windings. Action of Commutator, Methods

of Excitation. Armature Reaction-Effects and Remedial Measures, Interpoles

III and Compensating Winding, Commutation Process: Causes of Bad 14

Commutation, Method of Improving Commutation, Operating Characteristics.

Starters, Speed Control, Losses, Efficiency and Testing Of D.C. Machines

(Hopkinson’s And Swinburn’s Test).

Text Book:

J. Nagrath& D.P. Kothari, "Electric Machines” Tata McGraw Hill. AshfaqHussain, “Electric Machines”, Dhanpatrai& Sons.

References:

Irving L. Koscow, “Electric Machine and Transformers”, Prentice Hall of India. M.G. Say, “The Performance and

Design of AC machines”, Pit man & Sons.

Bhag S. Guru and Huseyin R. Hizirogulu, “Electric Machinery and Transformers” Oxford University Press.

B.R. Gupta &VandanaSinghal, “Fundamentals of Electric Machines”, 3rd Ed., New Age International. A.E. Fitzgerald, C.Kingsley JR and Umans, ”Electric Machinery” 6th Edition, Tata McGraw Hill, International Student Edition.

Bhimbra, P.S, “Electric Machines”, Khanna Publishers.



29

ENE 4001: ANALOG ELECTRONICS

SEMESTER IV L-T-P: 3-1-0

Module Content Teaching Hour

I

Review of transistors: all configurations of BJTs and FETs with their characteristics. Feedback: General Feedback Structure; Properties of Negative Feedback; Series-series, Series-shunt, Shunt-series and Shunt-shunt Feedback Amplifiers. Oscillators:-Conditions for oscillations Basic Principle of Sinusoidal Oscillator, R-C ,LC Oscillators. Circuit Mirror Circuits: Current Mirrors using BJT and MOSFETs. Operational Amplifier: Basic Information of Op-Amp, The ideal Operational Amplifier, Operational Amplifier Internal Circuit.

14

II

Operational Amplifier Characteristics and Applications : DC and AC Characteristics, Instrumentation Amplifier, V to I and I to V converter, Op-Amp Circuits using diodes, Sample and Hold Circuit, Log and Antilog Amplifier, Multiplier and Divider, Differentiator, Integrator, Electronic Analog Computation. Active Filters : First and Second order LP, HP, BP, BS and All pass active Filters Comparators and Waveform Generators: Comparator, Regenerative Comparator (Schmitt Trigger), Square Wave Generator (Astable Multi vibrator), Mono stable Multi vibrator, Triangular Wave Generator.

14

III

Voltage Regulator: Series Op-Amp Regulator, IC Voltage Regulators 555 Timer :Description of Functional Diagram, Mono stable Operation, Astable Operation, Schmitt Trigger. Phase-Locked Loop : Basic Principles, Phase Detector/Comparator, Voltage Controlled Oscillator (VCO), Low Pass Filter, Monolithic Phase-Locked Loop, PLL Applications A/D and D/A Converters- Weighted Resistors & R-2R D-A Converter, Flash Type, Single Ramp & Dual Ramp A-D Converters.

13

Text Books: A.S. Sedra and K.C. Smith “Microelectronics Circuits”4th Edition, Oxford University Press ( India). Roy Choudhury, Shail B. Jain “Linear Integrated Circuits”, 4th Edition, New Age International Publishers R.A. Gayakwad, “OP-AMP and Linear Integrated Circuits” Third edition, Prentice Hall of India. Robert L. Boylestad and Louis nashel sky, “Electronic devices and circuit theory”, Pearson Education/PHI, New Delhi

L–T–P

Credits: 04



30

CSE4070: DATA STRUCTURES & APPLICATIONS Prerequisite: Fundamentals of Computer Programming, Problem solving using Computers.

Module No.

Content Teaching

Hours

I

Introduction: Basic Terminology, Elementary Data Organization, Properties of an Algorithm, Efficiency of an Algorithm, Time and Space Complexity, Asymptotic Notations - Big Oh. Linked Lists: Implementation of Singly Linked Lists, Doubly Linked List, Circular Linked List, Operations on a Linked List - Insertion, Deletion, Traversal; Generalized Linked List, Polynomial Representation and Addition. Stacks: Primitive Stack Operations - Push & Pop, Array and Linked Implementation of Stack in C, Application of Stack: Prefix and Postfix Expressions, Evaluation of Postfix Expression, conversion of infix to postfix expression, Recursion, Principles of Recursion, Tail Recursion, Removal of Recursion, use of stack in Recursion.

14

II

Queues: Operations on Queue - Add, Delete operations, Implementation of Queue Using Array and Linked List, Circular Queues, Dequeue and Priority Queue. Trees: Basic Terminology, Array Representation and Dynamic Representation; Complete Binary Tree, Extended Binary Trees, Tree Traversal Algorithms - Inorder, Preorder and Postorder. Search Trees: Binary Search Trees (BST), Insertion and Deletion in BST, Introduction to B tree.

13

III

Graphs: Terminology, Adjacency Matrices, Adjacency List, Graph Traversal - Depth First Search and Breadth First Search; Spanning Trees, Minimum Cost Spanning Trees - Prims and Kruskal Algorithm; Shortest Path Algorithm - Dijkstra Algorithm. Searching: Sequential Search, Binary Search. Sorting: Bubble Sort, Selection Sort, Insertion Sort, Quick Sort, Two Way Merge Sort, and Heap Sort. Hashing: Hash Function, Collision Resolution Strategies.

13

Text Book:

Horowitz and Sahani (2004-05), “Fundamentals of Data Structures”, 3rd Edition, W H Freeman & Co. Reference Books:

Aaron M. Tanenbaum, YedidyahLangsam and Moshe J. Augenstein (2009), “Data Structures Using C and C++”, 2nd Edition, PHI.

Jean Paul Trembley and Paul G. Sorenson (2007), “An Introduction to Data Structures with Applications”, 2nd Edition, TMH.

R. Kruse, “Data Structures and Program Design in C” (2004), 2nd Edition, Pearson Education. LipschutzSchaum’s Outline Series (2010), “Data Structures”, 12th Reprint, TMH. G A V Pai (2009), “Data Structures and Algorithms”, TMH.

Credits: 03 L–T–P: 3–0–0 Semester IV



31

EEE4082: ELECTRICAL MACHINE LAB-I

Credits: 01 Semester IV L–T–P: 0–0–2

Module Content

Teaching

No.

Hours

To obtain magnetization characteristics of a D.C. shunt generator.

To obtain load characteristics of a compound generator (a)

cumulatively compounded (b) differentially compounded.

To obtain load characteristics of a D.C. shunt generator

To obtain efficiency of a dc shunt machine using Swinburn’s test.

To perform Hopkinson’s test and determine losses and efficiency of

DC machine.

To obtain speed-torque characteristics of a dc shunt motor.

To obtain speed control of dc shunt motor using (a) armature

I

resistance control 24

(b) field control

To study Ward Leonard method of speed control of dc motor.

To perform polarity and ratio test of single phase transformer.

To perform open circuit and short circuit test in single phase

transformer and find efficiency and voltage regulation.

To obtain efficiency and voltage regulation of a single phase

transformer by Sumpner’s test.

To perform polarity and ratio test on 3-phase transformer.

To study various connections of 3-pahse transformers.

To study Scott connection of transformers.



32

EEE4081: SIMULATION LAB-II


Module No.


I

1) To solve set of linear algebraic equation using left operation vector. Hence extend the concept for the underdetermined & over determined systems by “ rrev” & “pinv” commands

2) To study various relational & logical operator and hencewrite a script file to

plot the function y= 15 √4x +10 x≥9 = 10x+10 0≤x<9 =10 x<0 for -5≤x≤30

3) To study various plotting commands like axis, fplot,grid,plot,title,xlabel,ylabel and hence plot the polynomial of the form ax5+bx4+cx3+dx2+ex+f over the range –x1≤x≤x2 with a spacing of 0.01.

4) To understand various commands for 3D plots like contour , mesh,surf,meshgrid and hence create a surface plot & contour plot of the function z=(x-2)2+2xy+y2.

5) To understand the polyfit&polyval commands. Hence Fit a cubic polynomial to

the data and use the fit to estimate the best possible solution.

6) To understand various numerical integration function like quad,dblquad,polyintetc Use the commands to solve a double integral with definite limits

7) To study various histograms functions like bar, histand hence solve the

following problem: In 50 tests of thread, the number of times 91, 92, 93, 94, 95, or 96 N was measured was 7, 8, 10, 6, 12, and 7, respectively. Obtain the absolute and relative frequency Histograms.

8) To understand various LTI object functions like sys,sys1,sys2.Hence obtain the state model for the reduced-form model 5d2x/dt2+7 dx/dt + 4x=u(t)

9) Draw a series R-L circuit using simulink and hence plot power versus load

resistance graph to verify maximum power transfer theorem.

10) Draw the single phase half wave & full wave rectifier with resistive load using simulink. Plot the output voltage & current waveforms and hence find the values of output voltages & currents.



33

ENE4081 ANALOG ELECTRONICS LAB

Credits:01 Semester IV L-T-P: 0-0-2

Module Contents Teaching

Hours

1. To Study V-I Characteristic of JFET and MOSFET. 2. Realization of BJT as a Buffer Amplifier. 3. Realization of Multistage Amplifier Using BJT and Calculation of

Current Gain. 4. Realization of Tuned Amplifier and its Application as Hartley/ Colpitt

Oscillator. 5. Realization of comparator and zero crossing detector using op- Amp. 6. Realization of adder and subtractor using op-Amp. 7. Realization of 2nd order active low pass and high pass filter. 8. Realization of triangular and sine wave generator using op-Amp. 9. Realization of Astable and Mono stable multi vibrator using IC 555. 10. Realization of voltage regulator using IC 723. 11. Realization of voltage controlled oscillator using IC 8038/2206. 12. To study PLL and analyze the locking and capturing frequency range.



34

CSE 4090: DATA STRUCTURE LAB


Module Content

Lab Hours

No.

Program to demonstrate the various operations on Array based stack.

Program to convert an infix expression into postfix expression.

Program to evaluate a given postfix expression.

Program to generate Fibonacci series using Recursion.

Program to demonstrate the implementation of various operations on

linear Queue represented using an Array.

Program to implement various operations in a Singly Linked List.

Program to implement insertion, deletion and Traversal in a doubly

linked List.

I Program to implement polynomial addition using Linked List. 24

Program to demonstrate the implementation of insertion and

traversals on a binary search tree.

Program to implement Dijkstra’s Algorithm to find the shortest path

between source and destination.

Program to search a given element as entered by the user using

Sequential Search.

Program to demonstrate the use of binary search to search a given

element as entered by the user.

Implementation of various sorting algorithms like Bubble Sort,

Insertion Sort, Selection Sort, Merge Sort, Quick Sort and Heap Sort.



35

AHE4081: SOFT SKILLS-II


Objectives:

To make the students aware of the primary skills and sub skills involved in using English effectively at the contemporary corporate workplace with a global presence. To provide practice and guidance to enhance skills to the proficiency level expected by any organization.


No.

Introduction to English and Grammar.

Speaking face to face vs. over the phone.

Auxiliary and Modal verbs.

I 4 Techniques of reading- Skim, Scan, Intensive, Extensive.

10

ABC of writing, The KISS concept.

Presenting ideas, information and opinions with clarity.

Listening for information and making inferences.

Intonation, Word stress, Pacing, Sound clarity.

Second level of reading to interpret information

Subject Verb Agreement

Understanding ideas and making inferences

II Indianism, Question Tags, Phrasal verbs

10

Prepositions, Active and Passive voice

Third level reading and data interpretation

Sentence stress, connected speech

Tenses

Adverbs, Adjectives, Modifiers, Collocation

Discussing data and coming to conclusions

Link expressions, Compound nouns

III Negotiation skills 10

Business quiz, idioms and phrases

Individual presentation on speaking and writing

Feedback and Poster creation

References:

Hornby, A.S., An Advanced Learners’ Dictionary of Current English, OUP. Murphy, Raymond, Intermediate English Grammar, Cambridge University Press. Rizvi, Ashraf, M. Effective Technical Communication. New Delhi: Tata McGraw Hill. Infosys modules on English lab. PPT slides & videos provided by Infosys.

Material:

Audio-Video Material available in the Language Lab.



36

EEE5002: CONTROL SYSTEM

(Revised syllabus effective from session 2016-17)

Credits: 04 Semester V L-T-P: 3-1-0

Module No.

Content No. of

Lecture

I

The Control System: Open Loop & Closed Control; Servomechanism, Physical Examples. Transfer Functions, Block Diagram Algebra, Signal Flow Graph, Mason’s Gain Formula Reduction of Parameter Variation and Effects of Disturbance By Using Negative Feedback Control System Components: Constructional and Working Concept of Ac Servomotor, Synchros and Stepper Motor

12

II

Time Response Analysis: Standard Test Signals, Time Response of First and Second Order Systems, Time Response Specifications, Steady State Errors and Error Constants, Design Specifications of Second Order Systems: Derivative Error, Derivative Output, Integral Error and PID Compensations, Design Considerations for Higher Order Systems, Performance Indices Stability and Algebraic Criteria: Concept of Stability and Necessary Conditions, Routh-Hurwitz Criteria and Limitations. Root Locus Technique: The Root Locus Concepts, Construction of Root Loci

14

III

Frequency Response Analysis: Frequency Response, Correlation Between Time and Frequency Responses, Polar and Inverse Polar Plots, Bode Plots Stability in Frequency Domain: Nyquist Stability Criterion, Assessment of Relative Stability: Gain Margin and Phase Margin, M&N circles Introduction to Design: The Design Problem and Preliminary Considerations Lead, Lag and Lead-Lag Networks, Design of Closed Loop Systems Using Compensation Techniques in Time Domain and Frequency Domain. Overview of State Variable Technique: Overview of State Variable Technique, Conversion of State Variable Model to Transfer Function Model and Vice-Versa, Diagonalization, Controllability and Observability and Their Testing, Linear State Variable Feedback.

14

Text Books:

● Nagrath&Gopal, “Control System Engineering”, New age International.

References: ● Norman S. Nise, “Control System Engineering”, Wiley Publishing Co. ● Ajit K Mandal, “Introduction to Control Engineering” New Age International. ● R.T. Stefani, B.Shahian, C.J.Savant and G.H. Hostetter, “Design of Feedback Control Systems”, Oxford

University Press. ● N.C. Jagan, “Control Systems”, B.S. Publications. ● K. Ogata, “Modern Control Engineering”, Prentice Hall of India. ● B.C. Kuo&FaridGolnaraghi, “Automatic Control System”, Wiley India Ltd. ● D.RoyChoudhary, “Modern Control Engineering”, Prentice Hall of India.



37

EEE-5001: ELECTRICAL MACHINES-II (Revised syllabus effective from session 2016-17)



Lecture

I

Synchronous Machine-I: Constructional Features, EMF Equation, Winding Coefficients, Rotating Magnetic Field, Armature Reaction and Two Reaction Theory, Phasor Diagram based on Two Reaction Theory, Expression for Power developed in terms of load angle, OC and SC Tests, Voltage Regulation by Synchronous Impedance Method, MMF Method, ASA Method, Operation on Infinite Bus bar, Parallel Operation of Synchronous Generators, Active and Reactive Power Control of three phase alternators operating on infinite bus bar.

14

II

Synchronous Machine-II: Starting of Synchronous Motors, Effect of Variation of Field Current at constant load and V-Curves, Synchronous Condenser, synchronizing power and torque, hunting. Applications of synchronous motors, Circle diagrams Three phase Induction Machine-I: Constructional Features, Principle of Operation, Phasor Diagram, Equivalent Circuit, Power flow and Efficiency, Relation between rotor power input, mechanical power developed and rotor copper loss, Expression for torque and Torque-Slip Characteristics, Methods of starting of three phase induction motor

14

III

Three Phase Induction Machine-II: Determination of parameters of equivalent circuit by no load and blocked rotor tests,speed control using stator & rotor side control schemes Deep Bar and double cage rotors, harmonics and its effects: cogging and crawling. Induction Generator and its applications. Single Phase Induction Motor: Double Revolving Field Theory, equivalent circuit, no load and blocked rotor tests. Different types of single phase induction motors: starting methods, characteristics and applications.

14

Text Book:

J. Nagrath and D.P. Kothari, "Electric Machines” Tata McGraw Hill. AshfaqHussain, “Electric Machines”, Dhanpatrai and Sons.

Reference Books:

M.G. Say, “The Performance and Design of AC machines”, Pit man & Sons. J.B.Gupta,” Theory and Performance of Electrical Machines”, S.K. kataria and Sons. Bhimbra, P.S, “Electric Machines”, Khanna Publishers. A.E. Fitzgerald, C.Kingsley JR and Umans, “Electric Machinery” 6th Edition, Tata McGraw Hill,

International Student Edition.



38

EEE 5004: ELEMENTS OF POWER SYSTEM (Revised syllabus effective from session 2016-17)

Credit: 04 Semester V L-T-P:3-1-0


Lecture

I

Power System Overview Transmission Line: Types of Conductors, Bundled Conductors, Transmission Line Resistance (Skin & Proximity Effect), Inductance & Capacitance, GMR and GMD Method for calculations of Inductance & Capacitance of 1-phase & 3-phase Single circuit & Double Circuit Line. Models & Performance of Transmission Line: Characteristics & Performance of Power Transmission Lines- Short, Medium & Long Lines, Generalized Constant & Voltage Regulation, Ferranti Effect & Surge Impedance Loading. Mechanical Design of Overhead Transmission Line: Tension & Sag Calculation, Effect of Weather Conditions & Vibration Dampers.

14

II

Insulators: Insulator Types, String Efficiency & Methods to Improve String Efficiency (Capacitance Grading & Guard Ring). Corona: Corona Visual & Disruptive, Critical Voltage, Corona Loss, Factors Affecting Corona, Methods of Reducing Corona, Electrostatic & Electromagnetic Interference with Communication Lines. Insulated Cables: Constructional Features, Parameters, Cable Laying Procedures, High Voltage Cables & Thermal Characteristics Fault Location. Distribution System: Primary & Secondary Distribution, Ring Main & Radial System, Systematic Design of Distribution System.

14

III

Representation of Power System: Single Line Diagram, Per Unit System, Y-Bus & Z-Bus Formulation. Load Flow Study: Load Flow Problem, Power Flow Equations, Load Flow Using gauss Seidal& Newton Raphson Methods, Decoupling Between Real & Reactive Power Control, Decoupled & Fast Decoupled Method, Reactive Power Compensation.

14

Text Book:

D.P. Kothari and I.J. Nagarath,”power System Engineering”, TMH. HadiSaadat “Power system Analysis” MacGraw Hill Publication. W.D. Stevenson, “Elements of Power Systems Analysis”, McGraw Hill.

Reference Book:

B.R. Gupta,”Power System Analysis & Design”, S. Chand & Co. W.D. Stevenson,”Elements of Power System Analysis”, McGraw Hill. Chakraborthy, Soni,Gupta&Bhatnagar, “Power System Engineering”, DhanpatRai& Co.



39

ENE-5001: DIGITAL ELECTRONICS (Revised syllabus effective from session 2016-17)

Credit: 04 Semester V L-T-P: 3-1-0


Lecture

I

Logic Families, Diode, BJT & MOS as a switching element, concept of transfer characteristics, Input characteristics and output characteristics of logic gates, Fan-in, Fan-out, Noise margin, circuit concept and comparison of various logic families: TTL, CMOS Tri-state logic, open collector output, packing density, power consumption & gate delay. Digital system and binary numbers: Signed binary numbers, binary codes, Gray, ASCII code, EBCIDC code, Excess 3 code, Cyclic Codes, Error Detecting and Correcting Codes, Hamming Codes. Floating point representation, Parity checker. Gate-level minimization: K-Map, don’t care conditions, POS simplification, QuineMc- Clusky method.

14

II

Combinational Logic : Combinational circuits, analysis procedure, design procedure, Binary Adder-Sub tractor, Decimal Adder, Binary Multiplier, Decoders, Encoders, , De-multiplexer Multiplexers. Synchronous sequential logic: Sequential Circuits, Storage Elements: Latches, Flip Flops, Analysis of Clocked Sequential Circuits.

14

III

Registers and Counters: Shift Registers, Ripple Counter, Synchronous Counter, Other Counters. Memory and programmable logic : RAM, ROM, PLA, PAL, FPGA, PROM, EPROM, EEPROM Asynchronous Sequential Logic : Analysis procedure, circuit with latches, Design procedure, Reduction of state and flow table.

13

Text Books:

M. Morris Mano and M. D. Ciletti, “Digital Design” 4th Edition, Pearson Education. S. Salivahanan& S. Asivazhagan, “Digital Circuit & Design”, IInd Edition

REFERENCES:

John F.Wakerly, Digital Design, Fourth Edition, Pearson/PHI, 2006

John.M Yarbrough, Digital Logic Applications and Design, Thomson Learning, 2002.

Charles H.Roth. Fundamentals of Logic Design, Thomson Learning, 2003.

Donald P.Leach and Albert Paul Malvino, Digital Principles and Applications, 6thEdition, TMH, 2003.

William H. Gothmann, Digital Electronics, 2nd Edition, PHI, 1982.



40

CSE314/CSE5070: OBJECT ORIENTED PROGRAMMING USING C++ (B. TECH. (EE/EN))

Prerequisite: Fundamentals of Computer Programming, Problem solving using Computers.

Module No.

Content Teaching

Hours

I

Introduction: Structured versus Object-Oriented development, characteristics of Object-Oriented programming. Introduction of Class and Objects: class specification, class objects, accessing class members, defining member functions, outside member functions as inline, accessing member functions within a class, data hiding, access boundary of objects revisited, empty classes, pointers within a class, passing objects as arguments, returning objects from functions. Friend function and friend classes, constant parameters and member functions, static data and member functions, nested classes. Constructors and its type, destructor, constructor overloading, order of construction and destruction, nameless objects, dynamic initialization through constructors, constructors with dynamic operations.

14

II

Polymorphism: Function overloading, Operator overloading. Data conversion, Conversion between basic data types, conversion between objects and basic types, conversion between objects of different classes, Inheritance: Introduction, forms of inheritance, inheritance and member accessibility, multilevel inheritance, multiple inheritance, hierarchical inheritance, multipath inheritance and virtual base classes, hybrid inheritance.

13

III

Virtual functions: Introduction, need for virtual functions, pointer to derived class objects, definition of virtual functions, array of pointers to base class objects, pure virtual functions, abstract classes, virtual destructors. Generic programming with templates: Introduction, function templates, overloaded function templates, nesting of function calls, multiple arguments function templates, user defined template arguments, class templates.

13

References:

BjarneStroustrup (1997)”C++ Programming Language”, Addison Wesley, 3rd Edition. Robert Lafore (2000)”C++ Programming H. Schildt “– Teach yourself C++ TMH.

Credits: 03 L–T–P: 3–0–0 Semester V



41

EEE 5081: ELECTRICAL MACHINE LAB - II (Revised syllabus effective from session 2016-17)


Content Teaching

Hours

Hardware based experiments

1. To perform no load and blocked rotor tests on a three phase squirrel cage induction motor and determine equivalent circuit.

2. To perform load test on a three phase induction motor and draw: Torque -speed characteristics

3. To study speed control and reversal of direction of rotation of three phase induction motor by varying supply voltage.

4. To perform open circuit and short circuit tests on a three phase alternator and determine voltage regulation at full load and at unity, 0.8 lagging and leading power factors by (i) EMF method (ii) Z P F method

5. To determine V-curves and inverted V-curves of a three phase synchronous motor at no load

6. To determine Xd and Xq of a three phase salient pole synchronous machine using the slip test and draw the power-angle curve.

7. To study synchronization of an alternator with the infinite bus by using two bright and one dark lamp method.

Software based experiments

8. To determine speed-torque characteristics of three phase slip ring induction motor and study the effect of including resistance, or capacitance in the rotor circuit.

9. To determine speed-torque characteristics of single phase induction motor and study the effect of voltage variation.

10. To determine speed-torque characteristics of a three phase induction

by (i) keeping v/f ratio constant (ii) increasing frequency at the rated

voltage.

24

*Some hardware based experiments on single phase machine can also be performed by concerning the lab In-charge & the respective faculty.



42

ENE5081:Digital Electronics Lab (Revised syllabus effective from session 2016-17)


Module List of Experiments: Lab Hours

I,II & III

1. Realization of full-adder & full subtractor using logic gates and using

Boolean expression.

2. Realization of 4-bit even / odd parity checkers using Ex-OR gate.

3. Realization of 4-bit binary decoder/ demultiplexer.

4. Realization of 2-bit/ 4-bit multiplexer.

5. Realization of decimal to BCD encoder using IC 74147.

6. Realization and implementation of RS, JK, T and D flip-flop using logic

gates.

7. Realization and implementation serial in parallel out and parallel in

serial out shift register.

8. Realization and implementation 4-bit binary ripple counter using JK

flip-flop.

9. Realization and implementation of 2-bit up/down synchronous

counter.

24

*Three or more experiments will be performed based on simulation by concern faculty.



43

EEE5082: CONTROL SYSTEM LAB (Revised syllabus effective from session 2016-17)



I,II & III

Hardware based

1. To determine response of first order and second order systems for step

input for variousvalues of constant ’K’ using linear simulator unit and

compare theoretical and practicalresults.

2. To study P, PI and PID temperature controller for an oven and compare

their performance.

3. To study and calibrate temperature using resistance temperature

detector (RTD)

4. To design Lag, Lead and Lag-Lead compensators using Bode plot.

5. To study DC position control system

6. To study synchro-transmitter and receiver and obtain output V/S input

characteristics

7. To determine speed-torque characteristics of an ac servomotor.

8. To study performance of servo voltage stabilizer at various loads using

load bank.

9. To study behaviour of separately excited dc motor in open loop and

closed loop conditions atvarious loads.

10. To study PID Controller for simulation proves like transportation lag.

Simulation Based Experiments

11. To determine time domain response of a second order system for step

input and obtain performance parameters.

12. To convert transfer function of a system into state space form and vice-

versa.

13. To plot root locus diagram of an open loop transfer function and

determine range of gain ‘k’fir stability.

14. To plot a Bode diagram of an open loop transfer function.

15. To draw a Nyquist plot of an open loop transfer functions and examine

the stability of the closed loop system.

24



44

CSE385/CSE5090: C++ PROGRAMMING LAB

(B. TECH. (EC/ME/EE/EN))

Prerequisite: Students need to be familiar with the basic concepts of programming designing.

Outcome:

At the end of the course, students willget the all concepts of object oriented with their implementation.

Module No.

Content Lab

Hours

I

Programs Based on the Concepts of:

Class and Object, Reference Variable, Use of Scope Resolution Operator,

Default Arguments, Inline Function.


Constructors, Destructors, Friend Function, Object as Parameter, Object

as an Arguments and Keyword Static.


Function Overloading, Operator Overloading and Type Conversion.


Inheritance, Virtual Function, Abstract Class, This Pointer.


Template.

24

Credits: 02 L–T–P: 0–0–4 Semester V



45

CSE324/CSE6070: ESSENTIALS OF INFORMATION TECHNOLOGY (B. TECH. (EE/EN))

Prerequisite: Fundamentals of Computer Programming, Problem solving using Computers.

Module No.

Content Teaching

Hours

I

Introduction to JAVA Java V/s C++, Java Variables:- Local Variable, Instance Variable, Reference Variable, Java Primitives, Java Operators, Access Modifier, Command Line arguments, Class & Object, Constructor, Method Overloading, Keyword: Static, this, super and final, Overriding, Polymorphism, Inheritance, Packages, Abstract class, Interfaces, Exception Handling, Multithreading,

14

II

DATABASE MANAGEMENT SYSTEM Introduction: An Overview of Database Management System, Data Model Schema and Instances, Data Independence and Database Language (DDL, DML, DCL); Database Development Life Cycle (DDLC), ER Model Concepts, Keys with explanation, Relational Data Model Concepts, Integrity Constraints, Entity Integrity, Referential Integrity, Keys Constraints, Domain Constraints. Introduction to SQL: Data types, Writing DDL and DML Commands, Insert, Update and Delete Operations; Manipulations on Select statement; Variants of conditions used in where clause; Aggregate Functions, Use of Group By; Join, Writing Sub-Queries; Joins, Unions, Intersection, Minus. Database Design and Normalization: Functional Dependencies, Normal Forms, First, Second, Third Normal Forms, BCNF.

13

III

OPERATING SYSTEM Introduction: Operating System and its classification, Booting, System Calls, Operating System Functions and Services. Processes: Process Concept, Process States, Process State Transition Diagram, Process Control Block, Threads, Process Synchronization. CPU Scheduling: Scheduling Concept, Scheduling Algorithms. Deadlock: Deadlock Characterization, Prevention, Avoidance, Detection and Recovery. Memory Management: Multiprogramming with fixed and variable Partitions, Paging, Segmentation, Virtual Memory, Demand Paging, Page Replacement Algorithms, Disk Scheduling.

13

References:

Naughton, Schildt,(2002) “The Complete Reference JAVA2”, TMH Elmasri and Navathe (2010), “Fudamentals of Database Systems”, 6th Edition, Addision Wesley Silberschatz, Galvin and Gagne (2005), “Operating Systems Concepts”, 7th Edition, Wiley. Forouzan B. A. (2004), “Data Communication and Networking”, 4th Edition, McGrawHill.

Credits: 03 L–T–P: 3–0–0 Semester VI



46

ENE6001: POWER ELECTRONICS (Revised syllabus effective from session 2016-17)

Credits: 04 Semester VI L-T-P: 3-1-0

Module No.

Content No. of Lecture

I

Thyristor: Construction, V-I and Switching characteristics (Turn-On And Turn-Off), Two Transistor Model, Methods of Turn-On, Operation of GTO, DIAC, TRIAC, Firing Circuits for SCR (R, RC Half Wave and RC Full Wave and UJT Triggering Circuits), Protection of Devices, Series and Parallel Operation of Thyristors. Commutation: Commutation Techniques of Thyristor.

14

II

Phase Controlled Converters: Single Phase Half Wave Controlled Rectifier With Resistive and Induction Loads, Effects of Freewheeling Diode, Single Phase Fully Controlled and Half Controlled Bridge Converters, Performance Parameters, Three Phase Half Wave Converters, Three Phase Fully Controlled and Half Controlled Bridge Converters, Effect of Source Impedance, Single Phase and Three Phase Dual Converters. Inverters: Introduction (VSI), VSI-Single Phase Half and Full Bridge Inverters for R, RL And RLC Loads, Three Phase Bridge Inverters 180° and 120° Mode Operations.

13

III

Inverters: CSI-Single Phase Series Resonant and Parallel Inverters,Voltage Control of Inverters, Harmonic Reduction Techniques. DC-DC Converters: Principle of Step-Down Chopper, Step Down Chopper With R-L Load, Principle of Step-Up Chopper and Operation With RL Loads, control strategies for varying duty cycle, Classification of Choppers and Multiphase Choppers. Cyclo converters: Basic Principle of Operation, Single Phase to Single Phase, Three Phase to Single Phase and Three Phase to Three Phase Cyclo converters, Output Voltage Equation. AC Voltage Controllers: Introduction, Single Phase Ac Voltage Controller With Resistive and Inductive Loads, Three Phase Ac Voltage Controllers (Various Configurations And Comparison Only).

15

Text Books: M. H. Rashid, Power, “Electronics: Circuits, Devices & Applications”, Prentice Hall of India Ltd. P.S. Bhimbra, “Power Electronics”, Khanna Publishers.

References: M.S. JamilAsghar, “Power Electronics”, Prentice Hall of India Ltd. Chakrabarti&Rai, “Fundamentals of Power Electronics & Drives”, DhanpatRai& Sons. Ned Mohan, T. M. Undeland and W. P. Robbins, “Power Electronics: Converters, Applications and

Design”,Wiley India Ltd. S. N. Singh, “A Text Book of Power Electronics”, DhanpatRai& Sons.M.D. Singh &K. B.

Khanchandani“Power Electronics”, TMH.

V.R. Moorthy, “Power Electronics: Devices, Circuits, Industrial Applications”, Oxford Univ. Press.



47

ENE6002: MICROPROCESSOR (Revised syllabus effective from session 2016-17)



Lecture

I

Introduction to Microprocessor, Components of a Microprocessor: Registers, ALU and control & timing, System bus (data address and control bus), Microprocessor systems with bus organization. Microprocessor Architecture and Operations, Memory, I/O devices, Memory and I/O operations. 8085 Microprocessor Architecture, Address, Data And Control Buses, 8085 Pin Functions, Demultiplexing of Buses, Generation Of Control Signals, Instruction Cycle, Machine Cycles, T-States, Memory Interfacing

14

II

Assembly Language Programming Basics, Classification of Instructions, Addressing Modes, 8085 Instruction Set, Instruction And Data Formats, Writing, Assembling & Executing A Program, Debugging The Programs. Writing 8085 assembly language programs with decision, making and looping using data transfer, arithmetic, logical and branch instructions. Stack & Subroutines, Developing Counters and Time Delay Routines, Code Conversion, BCD Arithmetic and 16-Bit Data operations

14

III

Interfacing Concepts, Ports, Interfacing Of I/O Devices, Interrupts In 8085, Programmable Interrupt Controller 8259A, Programmable Peripheral Interface 8255A Advanced Microprocessors: 8086 logical block diagram and segments, 80286: Architecture, Registers (Real/Protected mode), Privilege levels, descriptor cache, Memory access in GDT and LDT, multitasking, addressing modes, flag register. Introduction to Microcontrollers and Embedded Processors

13

Text Book:

B Ram “Fundamental of Microprocessor & Microcontrollers”, DhanpatRai publication.

Reference Books: Ramesh S. Gaonkar , “Microprocessor Architecture, Programming, and Applications” with the 8085, Pub:

Penram International. N. Senthil Kumar, M. Saravanan, S. Jeevanathan, S. K. Shah “Microprocessors and Interfacing”, Oxford Daniel Tabak “Advanced Microprocessors”, McGrawHill. Douglas Hall “Microprocessor & Interfacing” , TMH. Savaliya M. T. “8086 Programming and Advance Processor Architecture”, WileyIndia. Triebel& Singh “The 8088 and 8086 Microprocessors”, Pearson Education. Kenneth Ayala “The 8051 Micro controller” 3rd Edition.



48

EEE6003: POWER SYSTEM ANALYSIS & PROTECTION (Revised syllabus effective from session 2016-17)

Credit: 04 Semester VI L-T-P: 3-1-0


Lecture

I

Fault Analysis: Symmetrical components analysis, Static & Dynamic Device Behavior, Symmetrical Fault, Symmetrical Components of Unsymmetrical Phasor, Sequence Impedance & Networks of Power System, Significance of Sequence Components, Power Invariance, Unsymmetrical Faults(LG, LL, LLG). Transient Stability Studies: Types of Stability, Swing Equation, Equal Area Criterion & its Applications, Step by Step Solution of Swing Curve, Factors Affecting Stability of System & Methods of Improving Stability.

14

II

Surge Phenomenon: Classification,Travelling Wave Equation for Long line, Surge Impedance. Introduction to Protection System: Introduction to Protection System & its Elements, Zone of Protection, Primary & Back-Up Protection, Desirable Qualities of protective Relaying. Relays: electromagnetic Attraction Type Relays, Concept of Time Setting Multiplier & Plug Setting Multiplier, Electromagnetic Induction Disc Type relay, Torque Equation, Instantaneous Over Current Characteristics, Inverse Definite Minimum Time Characteristics (IDMT), Definite Time Over Current Characteristics, and universal Torque Equation. Distance Relay: Impedance Relay, Drawback of simple Impedance Relay.

14

III

Distance relay: Directional Protection & Directional Relay, Concept of Maximum Torque Angle, Characteristics on R-X Diagram. Reactance & MHO Relays, Characteristics on R-X diagram, Limitation. Simple Differential Protection, operation under Internal & External Fault, Percentage Bias Differential protection. Circuit Breaking: Arc Formation, Properties of Arc, Extinction Theories, Re-Striking Voltage, RRRV, Current Chopping, Resistance Switching, Capacitive Current Interruption, Short Line Interruption, Circuit breaker Rating, Constructional features & Operation of Bulk oil & Minimum oil Circuit Breaker, Air blast CB , SF6 Circuit Breaker.

14

Text Book:

D.P. Kothari and I.J. Nagarath, ”Morden Power System Analysis”, Tata McGraw Hill Publication. Y.G. Paithankar& S.R. Bhinde, ”Fundamentals of Power System Protection”, Prentice Hall of India

BhaveshBhalia, R.P. Maheshwari, & N G Chothani” Protection & Switchgear”, Khanna Publication.

References: W.D. Stevenson, ”Elements of Power System Analysis”, McGraw Hill.

C.L. Wadhwa, ”Electrical Power System”, New Age International Limited. Badri Ram & D N Vishwakarma “Power System Protection & Switchgear”,Tata McGraw Hill Publication.



49

CSE395/CSE6090: INFORMATION TECHNOLOGY LAB

(B. TECH. (EE/EN))

Module No.

Content Lab

Hours

I

Programs related to java class variables and methods.

Program related to constructor and method overloading.

Program related to keyword static for variables, method and class.

Program related to Inheritance and Interfaces.

Program related to Multithreading concept

Program related to Exception Handling.

Write the queries for Data Definition and Data Manipulation Language.

Write SQL queries using logical operations (=, <, >, etc).

Write SQL queries using SQL operators.

Write SQL query using character, number, date.

Write SQL query based on group functions.

Write SQL queries for relational algebra operations.

Write SQL queries for extracting data from more than one table.

Write SQL queries for sub queries, nested queries.

Concepts for ROLL BACK, COMMIT & CHECK POINTS.

Understand of Linux operating system.

Basic command of Linux

Understanding Network devices

24

Credits: 01 L–T–P: 0–0–2 Semester VI



50

ENE6081: POWER ELECTRONICS LAB (Revised syllabus effective from session 2016-17)

Credits:1 Semester VI L–T–P: 0–0–2

Module

Content Teaching

No.

Hours

List of Experiments 1. To study V-I characteristics of SCR and measure latching and

holding currents.

2. To study UJT trigger circuit for half wave and full wave control. 3. To study single-phase half wave controlled rectified with (i) resistive load (ii) inductive load with and without free-wheeling diode. 4. To study single phase (i) fully controlled (ii) half controlled bridge rectifiers with resistive and Inductive loads. 5. To study three-phase fully/half controlled bridge rectifier with

resistive and inductive loads.

6. To study single-phase ac voltage regulator with resistive and inductive loads. 7. To study single phase cyclo-converter.

I

8. To study triggering of (i) IGBT (ii) MOSFET (iii) power transistor

24

9. To study operation of IGBT/MOSFET chopper circuit

10. To study MOSFET/IGBT based single-phase bridge inverter. 11. To obtain illumines control using TRIAC.

SOFTWARE BASED EXPERIMENTS (PSPICE/MATLAB)

12. To obtain simulation of SCR and GTO thyristor. 13. To obtain simulation of Power Transistor and IGBT.

14. To obtain simulation of single phase fully controlled bridge rectifier

and draw load voltage load current waveform for inductive load.

15. To obtain simulation of single phase full wave ac voltage controller and draw load voltage and load current waveforms for inductive load. 16. To obtain simulation of step down dc chopper with L-C output filter for inductive load and determine steady-state values of output

voltage ripples in output voltage and load current.



51

EEE 6082: POWER SYSTEM & PROTECTION LAB

(Revised syllabus effective from session 2016-17)



I,II & III

Hardware based

1. To calculate the ABCD parameters of transmission lines for Nominal-T

& Nominal-π models. Determine the efficiency & voltage regulation of

transmission lines. Also to study the Ferrenti effect on transmission

lines

2. To determine the fault location in the cables using Murray loop test.

3. To study the I-V characteristics of P-V cell.

4. To study the series and parallel operation of P-V module. Determine the

Efficiency of solar P-V module.

5. To study three phase short circuit fault in the transmission line.

6. To plot characteristics of % bias differential relay.

7. To plot the characteristics of over voltage relay & voltage restrained

relay.

8. To plot the characteristics of over current relay & Earth fault relay.

9. To study the Transformer differential protection operation using

differential relay for in & out zone trip faults.

Simulation Based Experiments

10. To obtain steady state, transient and sub-transient short circuit

currents of and 3 phase alternator.

11. To formulate Y-bus for a given power system network.

12. To perform symmetrical fault analysis in a given power system

13. To perform unsymmetrical fault analysis in a given power system for

LG, LL, LLG faults.

14. To perform the load flow analysis for a given power system network

using Gauss Seidal method.

24

* Some of the experiments based on relay, fault & load flow can be performed on ETAP software.



52

ENE6082: MICROPROCESSOR LAB



I,II & III

List of Experiments 8085/8086 Based Experiments

1. Recursive Routine for Finding Factorial N. 2. Assembly language Programs for 8086. 3. Assembly Language Programs for 8086 to address and data transfer. 4. Assembly Language Programs for 8086 to addition, subtraction. 5. Assembly Language Programs for 8086 to block transfer. 6. Assembly Language Programs for 8086 to find greatest numbers. 7. Look up table method for finding the ASCII of an alphanumeric code. 8. Interfacing with 8255 in I/O mode/BSR mode to 8085/8086 based system. 9. Interfacing with 8253to 8085/8086 based system. 10. To 8085/8086 based system verification of Interrupts. 11. Interfacing with ADC/DACto 8085/8086 based system. 12. Serial communication between two kits through RS-232C using 8251. 13. Signed Multiplication using Booth's Algorithm. 14. To perform microprocessor based stepper motor operation through 8085

kit. 15. Mini Project on some interfacing applications.

24



53

MBA 304/5034: INDUSTRIAL MANAGEMENT (WILL APPLICABLE FOR FINAL YEAR OF SESSION 2017-18)

Credits: 04 Semester VII L-T-P: 4-0-0

Objectives of the Course:

To help students to understand the important managerial dimensions of Industrial Management.

To make student’s able to apply their thoughts and subject understanding in real practice to support

industrial progress.

Module No.

Content Teaching

Hours

I

Introduction to Management- Concept, levels of Management, Management functions & skills. Planning & Organizing- Concept, Types of planning, Planning Process and premises, Concept of organization structure, Relationship between authority, responsibility and accountability. Directing & Leadership: Concept and principles of direction, Leadership style and traits. Motivation:-Maslow’s hierarchy of needs theory, Herzberg’s Motivator-hygiene theory, Alderfer’s ERG Theory, Vroom’s Expectancy theory. Controlling- Types of Controlling, Controlling Process. Staffing:-Concept, significance, Human resource Planning (HRP)Concept, significance and HRP Process. Performance Management: Definition, methods of appraisal: Critical Incidents Method, Comparative Evaluation Method (Ranking & Paired Comparisons), Management By Objectives, Assessment Centers, 360-Degree Feedback.

13

II

Financial Management: Meaning, Objective, Financial Management Functions:-Financial Decision, Investment Decision, Dividends Decision. Profit & Loss statements, Balance sheet preparation, cash flow analysis, Break even Analysis. Time value of Money, Capital budgeting and its techniques: Net present value (NPV), Internal rate of Return (IRR) and Payback method. Material Management: Concept, Scope and objective of Material Management, Inventory Management, Material flow process, Deterministic and Probabilistic model of Inventory control, Material requirements planning, Brief introduction of Just-in-Time(JIT), Enterprise Resource Planning (ERP), Supply chain Management(SCM), Business process re-engineering.(BPR)

14

III

Marketing Management: Marketing: Definition, Scope, Marketing Mix:-Product, Price, Place, Promotion. Segmenting, Targeting and Positioning. Quality Management: Concept of Quality, types of Quality: quality of design, conformance and performance, phases of quality management. An overview of Quality Management assistance tools: Ishikawa diagram, TQM, Kaizen, Five S(5S), six sigma. ISO 9000 : ISO 9001:2008, ISO 9000:2005, ISO 9004:2009, ISO 19011:2011.

13

Text Books:

Khanna, O.P. (2011) Industrial Engineering & Management. N.Delhi: DhanpatRai& Co. Pvt Ltd. Khanka,S.S. (2007). Entrepreneurial Development. N.Delhi: S.Chand& Company Ltd

References: Gopalakrishanan, P. (2005). Material Management. New Delhi: India:Prentice Hall of India.

Chandra, P. (2006). Projects. New Delhi: India: Tata McGraw-Hill Publishing Company Limited.

Desai,V.(2007). Dynamics of Entrepreneurship Development and Management. Mumbai: Himalaya Publishing House.

http://www.iso.org/iso/home/standards/management-standards/iso_9000.htm



54

EEE-401: SWITCHGEAR & PROTECTION

Credits: 04 Semester VII L–T–P: 3–1–0

Module Content

Teaching

No.

Hours

Introduction to Protection system:

Introduction to protection system & its elements, zone of protection, primary &

back-up protection, desirable qualities of protective relaying, review of CT & PT.

Relays:

Electromagnetic attraction type relays, concept of time setting multiplier & plug

setting multiplier, electromagnetic induction disc type relays, torque equation,

I Instantaneous over-current characteristics, Inverse definite minimum time 13

characteristics (IDMT),Definite time over-current

characteristics(DTOC),comparison between DTOC & IDMT relays, drawbacks of

over-current protection, Universal Torque equation, Distance protection using

simple impedance relay, drawbacks of simple impedance relay, directional

protection & directional relay, concept of maximum torque angle ,characteristics

on R-X diagram

Reactance relays & MHO relays- characteristics on R-X diagram, implementation,

limitations, Simple differential protection, operation under external & internal

II fault condition, percentage bias differential protection , Bus – bar protection, auto 13

reclosing, carrier current protection.

Protection of Transformer, generator and motor

Circuit Breaking

Arc formation, properties of arc, extinction theories, re-striking voltage, RRRV,

current chopping, resistance switching, capacitive current interruption, short line

interruption, circuit breaker ratings, Testing of circuit breakers-Direct & In-direct

III testing, Constructional features and operation of Bulk oil & minimum oil circuit

13

breakers, Air blast circuit breakers,SF6 circuit breakers & HVDC circuit breakers.

Static relays

Amplitude comparator & phase comparator, synthesis of MHO relay using static

phase comparator, synthesis of reactance relay using cosine type phase

comparator, synthesis of simple impedance relay using amplitude comparator.

Text Books:

Y. G. Paithankar and S R Bhide, “Fundamentals of Power System Protection”, Prentice Hall of India. S. S. Rao, “Switchgear and Protection”, Khanna publishers

References: B. Ram and D. N. Vishwakarma, “Power System Protection and Switchgear”, Tata Mcgraw Hill BhaveshBhalja , R.P.Maheshwari&NileshChothani, “ Protection & Switchgear”, Oxford university

press Nirmal-Kumar C Nair, Bhuvanesh A Oza, Vijay H Makwana, Rashesh P Mehta, “Power

system protection & switchgear”,Mcgraw Hill A.R. Van C. Warringtaon , “ Protective Relays- Their Theory and Practice, Vol. I & II” John Willey &

Sons.



55

EEE-402: ELECTRIC DRIVES


Module

Content

Teaching

Hour

Fundamentals of Electric Drives: Introduction, concept of electric drives,

classification, multi-quadrant operations, types of load, load torque components

and nature, constant torque and constant power operation, steady state and

transient stability of electric drive.

I Selection of Motor Power Rating: Thermal model of motor for heating and 14

cooling, classes of motor duty, determination of motor power rating for

continuous duty, short time duty and intermittent duty and load equalization.

Electric Braking: Purpose and types of electric braking, braking of dc, three

phase induction and synchronous motors.

Dynamics During Starting and Braking: Calculation of acceleration time and

energy loss during starting of dc shunt and three- phase induction motors and

methods of reducing energy loss during starting.

II

Power Electronic Control of DC Drives: Single-phase and three-phase 14

controlled converter fed separately excited dc motor drives(continuous

conduction only), dual converter fed separately excited dc motor drive and

brushless dc motor, supply harmonics, power factor and ripples in motor current

, chopper control of separately excited dc motor and dc series motor.

Power Electronic Control of AC Drives:

Three Phase induction Motor Drives: stator voltage control & soft start,

variable frequency control (voltage source inverter, current source inverter and

III

cyclo-converter based), stator current control, rotor resistance control and slip 13

power recovery control schemes.

Three Phase Synchronous Motor Drives: Cylindrical rotor motors, salient pole

motors, reluctance motor and permanent magnet synchronous motor.

References:

G.K. Dubey, “Fundamentals of Electric Drives”, Narosa publishing House. S.K.Pillai, “A First Course on Electric Drives”, New Age International. P.S.Bimbhra, “Power Electronics”, Khanna Publishers. M.Chilkin, “Electric Drives”,Mir Publishers, Moscow. Mohammed A. El-Sharkawi, “Fundamentals of Electric Drives”, Thomson Asia, Pvt. Ltd.

Singapore. N.K. De and PrashantK.Sen, “Electric Drives”, Prentice Hall of India Ltd. V.Subrahmanyam, “Electric Drives: Concepts and Applications”, Tata McGraw Hill.



56

EEE-403: ELECTRICAL INSTRUMENTATION AND PROCESS CONTROL

Credits: 04 Semester VIII L–T–P: 3–1–0

Module

Content Teaching

Hour

Introduction to Industrial Automation and control:Architecture of

industrial automation systems.

Introduction to Sensors and Measurement systems :

I Temperature measurement, pressure and force measurement, displacement 13

and speed measurement, flow measurement techniques, measurement of level,

humidity and ph.

Signal conditioning and processing estimation of errors and calibration.

Introduction to Process Control:

Process characteristics, proportional(P),integral(I),derivative(D),PI,PD and PID

Control modes, controller tuning.

Special Control Structures :

Feed-forward and ratio control, predictive control, control of systems with

II inverse response cascade control, overriding control, selective control, split 14

range control.

Electronic, pneumatic anddigital controllers.

Electrical Control elements: Construction and principle of operation of

solenoids, stepper motor, AC/DC motor, limit switches, relays, auto

transformer and magnetic amplifiers.

Introduction to Actuators:Flow control valves.

Control valves: Principle of operation and constructional details of solenoid

valves, diaphragmoperated valve, piston operated valve, valve positioners,

control valve characteristics and their sizing, temperature switches flow

III switches, interlocking and sequencing circuits.

13

Hydraulic Actuator systems: Principles, components and symbols, pumps and

motors, proportional and servo valves.

Pneumatic Control systems: System components, controllers and integrated

control systems.

Introduction to Sequence control: PLCs and relay ladder Logic.

References:

George Stephanopoulos, “Chemical Process Control: An Introduction to Theory and Practice”, Prentice-Hall, 1984.

Harrist P, “Process Control”, McGraw Hill. Johnson, Curtis D, “Process Control Instrumentation Technology”, John Wiley and Sons. B.C. Nakra&K.Chaudhry, “Instrumentation, Measurement and Analysis”, Tata McGraw Hill 2nd

Edition. A.K.Sawhney, “Advanced Measurements & Instrumentation”, DhanpatRai& Sons. E.O. Decblin, “Measurement System – Application & design”, McGraw Hill. Eckman D P , “Automatic Process Control”, Wiley Eastern, 1975. Liptak B. G., “Instrument Engineers Handbook”, CRC Press 3rd edition. Ronald P Hunta, PE, “Automated Process Control Systems: Concepts and Hadware”, Prentice Hall Inc.,

New Delhi. Eckman, Donal P, “Principles of Industrial Process Control”, John Wiley and Sons. LiptakBila G, “Process Measurement and Analysis”CRC Press 3rd edition.



57

EEE-404: POWER SYSTEM OPERATION AND CONTROL


Module Content

Teaching

No.

Hours

Introduction:

Structure of power systems, power system control center and real time computer

control, concept of energy control centre (or) load dispatch centre and the

functions, system hardware configuration – SCADA and EMS functions, network

topology, state estimation, security analysis and control.

I Various operating states:

13

Normal, alert, emergency, in-extremis & restorative states, state transition

diagram showing various state transitions and control strategies, power system

voltage stability.

System load variation:

Load-duration curve (daily, weekly and annual), load factor & diversity factor,

importance of load forecasting and simple techniques of forecasting.

Economic operation :

Concept and problems of unit commitment, input-output characteristics of thermal

and hydro-plants, system constraints, optimal operation of thermal units without

and with transmission losses, Penalty factor, incremental transmission loss,

transmission loss formula (without derivation).

Load frequency control:

II Concept of load frequency control, load frequency control of single area system, 13

turbine speed governing system and modeling, block diagram representation of

single area system, steady state analysis, dynamic response, control area concept,

P-I control, load frequency control and economic dispatch control.

Load frequency control of two area system:

Tie line power modeling, block diagram representation of two area system, static

and dynamic response.

Automatic voltage control:

Schematic diagram and block diagram representation, different types of Excitation

system.

Voltage and reactive power control:

Concept of voltage control, methods of voltage control by tap changing

III transformer, shunt compensation, series compensation, and phase angle 13

compensation.

Flexible AC transmission systems:

Concept and objectives of FACT’s controllers, structure & characteristics of

following FACT’s controllers - TCR, FC-TCR, TSC, SVC, STATCOM, TSSC, TCSC, SSSC,

TC-PAR, UPFC.

Text Books: D.P. Kothari & I.J. Nagrath, “Modern Power System Analysis” Tata McGraw Hill, 3rd Edition. P.S.R. Murty, “Operation and control in Power Systems” B.S. Publications. N. G. Hingorani& L. Gyugyi, “Understanding FACTS Concepts: and Technology of Flexible ac transmission

systems” IEEE press. A. J. Wood & B.F. Wollenburg, “Power Generation, Operation and Control “John Wiley & Sons.

References: O.I. Elgerd, “Electric Energy System Theory” Tata McGraw Hill Publishing Company Ltd. New Delhi,

Second Edition 2003. P. Kundur, “Power System Stability and Control” McGraw Hill Publishers, USA.



58

EEE-405: DIGITAL CONTROL SYSTEM


Module

Content Teaching

Hour

Signal Processing in Digital Control:

Basic control system, advantages of digital control and implementation

I problems, basic discrete time signals, z-transform and inverse z-transform.

14

Modeling of sample-hold circuit, pulse transfer function, solution of

difference equation by z- Transform method.

Design of Digital Control Algorithms:

Steady state accuracy, transient response and frequency response

specifications, digital compensator design using frequency response plots

and root locus plots.

II State Space Analysis and Design: 14

State space representation of digital control system, conversion of state

variable models to transfer functions and vice versa, solution of state

difference equations, controllability and observability, design of digital

control system with state feedback.

Stability of Discrete System:

Stability on the z-plane and Jury stability criterion, bilinear transformation,

Routh stability criterion on rth plane.

Lyapunov’s Stability in the sense of Lyapunov, stability theorems for

III continuous and discrete systems, stability analysis using Lyapunov’s 14

method.

Optimal digital control :

Discrete Euler Lagrange equation, max. min. principle, different types of

problem and their solutions.

Text Books:

B.C.Kuo, “Digital Control System”,Saunders College Publishing. M.Gopal, “Digital Control and State Variable Methods”, Tata McGraw Hill.

Reference Books: R.Leigh, “Applied Digital Control”, Prentice Hall, International. C.H. Houpis and G.B.Lamont, “Digital Control Systems :Theory, hardware, Software”, McGraw Hill.



59

EEE-406: POWER SYSTEM DYNAMICS AND STABILITY


Module

Content Teaching

Hour

System Modeling and Dynamics of Machine:

Modeling of synchronous machine: park’s transformation, equivalent circuit

&phasor diagram of synchronous generator, dynamics of synchronous

I generator connected to infinite bus system, modeling of excitation system, 15

prime mover and governing system; induction machine modeling.

Angular Stability: Review of stability concept, response to a step change in

mechanical power input, equal area criterion and its application, swing

II equation, numerical solution of swing equation, factors affecting stability,

14

multi-machine system stability, small signal stability of single machine

system , introduction to power system stabilizers.

Voltage Stability: Introduction, classification of voltage stability, factors

affecting voltage stability, voltage stability of a simple 2-bus system, tools

III for voltage stability analysis, voltage collapse and prevention of voltage 13

collapse.

Text Books :

Peter W. Sauer and M.A.Pai , “ Power System Dynamics & Stability”, Prentice Hall. P. Kundur , “Power System Stability and Control” , Mc-Graw Hill.

Reference Books: K. R. Padiyar , “Power System Dynamics -Stability & Control”, BS Publications. E.W. Kimbark , “Power System Stability” , Wiley-IEEE Press. C.P.Taylor , “Power System Voltage Stability” , Mc- Graw Hill.



60

EEE-407: DIGITAL SIGNAL PROCESSING


Module Content

Teaching

No.

Hours

Review of discrete time signals and systems, Sampling of CT signals:

Periodic sampling, Frequency domain representation of sampling,

Reconstruction of bandlimited signal from its samples, Discrete time

I processing of continuous time signals, Continuous time processing of

13

discrete time signals, Changing the sampling rate using discrete time

processing.

Discrete time systems: Linear time invariant discrete time systems,

Characterization of LTI systems.

Transform domain representation of signals and systems: The discrete time

Fourier transform ,The frequency response ,The transfer function ,Discrete

II Fourier series ,Discrete Fourier transform ,Computation of DFT ,Linear

14

convolution using DFT, FFT Algorithms, Direct Computation of the DFT

Radix-2 FFT algorithms, Gortezel Algorithm, Chirp Z-transform The z-

transform ,The region of convergence of z-transform

Structures for discrete time systems: Block diagram and signal flow

representation of constant coefficient , linear difference equation, Basic

structures for IIR systems, Basic structures for FIR systems ,Lattice

III structures, Effects of coefficient quantization, Effect of roundoff noise in

13

digital filters, Zero-input limit cycles

Filter design techniques: Design of discrete time IIR filters from

continuous time filters, Design of FIR filters by windowing, Optimum

approximation of FIR filters, Linear phase filters.

References:

John G Prokias, Dimitris G Manolakis, “Digital Signal Processing”, Pearson Education. Oppenheim & Schafer, “ Digital Signal Processing” PHI



61

EEE-409: ADVANCE CONTROL SYSTEM


Module

Content Teaching

Hour

State Space Analysis of Continuous System:

Review of state variable representation of continuous system, design of state

observer and controller.

Analysis of Discrete System:

I Discrete system and discrete time signals, state variable model and transfer function

14

model of discrete system, conversion of state variable model to transfer function

model and vice-versa, modeling of sample hold circuit, solution of state difference

equations, steady state accuracy, stability on the z-plane and Jury stability criterion,

bilinear transformation, Routh-Hurwitz criterion on rth planes.

Stability:

Lyapunov’s stability theorems for continuous and discrete systems, methods for

generatingLyapunov function for continuous and discrete system.

Non linear System:

II Types of non linearities, phenomena related to non-linear systems, analysis of non 13

linear systems, linearization method, second order non-linear system on the phase

plane, types of phase portraits, singular points, system analysis by phase-plane

method and describing function method.

Optimal Control:

Introduction, formation of optimal control problem, calculus of variations

minimization of functions, constrained optimization, Pontryagin’s minimum

maximum principle.

III Adaptive Control: 13

Introduction, modal reference adaptive control systems, controller structure, self

tuning regulators. Introduction to neural network, fuzzy logic and genetic

algorithms.

Text Books: M.Gopal, “Digital Control and State variable Methods”, Tata McGraw Hill. AjitK.Madal, “Introduction to Control Engineering: Modelling, Analysis and Design”, New Age

International. D.Landau, “Adaptive Control”, Marcel Dekker Inc. S.Rajasekaran&G.A.VjayalakshmiPai, “Neural Networks,Fuzzy Logic and Genetic Alogorithms: Synthesis

and Applications”, Prentice Hall of India. Reference Books:

Donald E. Kiv, “Optimal Control Theory: An Introduction”, Prentice Hall. B.C. Kuo, “Digital Control Systems”, Sounders College Publishing. C.H.Houpis and G.B.Lamont,“Digital Control Systems:Theory,Hardware, Software”,McGraw Hill. Hassan K. Khalil, “Nonlinear systems”, Prentice Hall.



62

EEE-411: BIO-MEDICAL INSTRUMENTATION


Module Content

Teaching

No. Hours

The origin of biopotentials, bioelectric signals (ECG, EMG, EEG, EOG & ERG)

and their characteristics, bioelectrodes, electrodes tissue interface, contact

I impedance, effects of high contact impedance, types of electrodes, electrodes

13

for ECG, EEG and EMG.

The origin, acquisition, processing, and analysis of electrical heart signals,

recording and interpretation of electrocardiogram (ECG).

Blood pressure and sound, phonocardiography, pulse pickup, measurement

of flow and volume of blood, electromagnetic and ultrasonic flowmeter,

measurements of the respiratory System, lungs (spirometry, EIT), chemical

II biosensors. 13

An introduction to therapeutic devices (cardiac pacemakers and

defibrillators), An introduction to therapeutic devices for ears (hearing

implants) and eyes (retinal implants).

Patient Monitoring System:

Heart rate measurement pulse rate measurement, respiration, rate

measurement, blood pressure measurement, microprocessor applications in

patient monitoring.

X- Ray Machine:

III Basic X-ray components and circuits, types of X-ray machines e.g. general

14

purpose, dental image intensifier system, table shooting and maintenance of

X- ray machine.

Safety Aspect of Medical :

Gross current, micro current shock, safety standards rays and

considerations, safety testing instruments, biological effects of X-rays and

precautions.

Text Book:

John. G. Webster, “Medical Instrumentation Application and Design”, Wiley India Pvt Ltd. L. A. Geddes, L. E. Baker, “Principles of Applied Biomedical Instrumentation”, John Wiley. Joseph J. Carr, John M. Brown ,“Introduction to Biomedical Equipment Technology”, Pearson.

Reference Books:

Leslie Cromwell, “Biomedical Instrumentation and Measurements” , Prentice-Hall. R.S. Khandpur, “Handbook of Biomedical Instrumentation”, TMH, New Delhi. Sanjay Guha, “Medical Electronics and Instrumentation”, University Publication. Edwand J. Bukstein, “Introduction to Biomedical Electronics”, Bobbs-Merrill Co.



63

EEE-412: SMART GRID


Module Content

Teaching

No.

Hours

Introduction to Smart Grid

Evolution of electric grid, concept of smart-grid, definitions, need of smart grid, functions of smart

grid, opportunities & barriers of smart grid, difference between conventional & smart grid, concept

I of resilient &self healing grid, present development & international policies on smart grid.

14

Smart Grid Technologies: Part 1

Introduction to smart meters, real time pricing, smart appliances, automatic meter reading(AMR),

outage management system(OMS), plug in hybrid electric vehicles(PHEV), vehicle to grid, smart

sensors, home & building automation, phase shifting transformers.

Smart Grid Technologies: Part 2

Smart-substations, substation automation, feeder automation. geographic information system(GIS),

intelligent electronic devices(IED) & their application for monitoring & protection, smart storage like

Battery, SMES, pumped hydro, compressed air energy storage, wide area measurement

II system(WAMS), phase measurement unit(PMU).

13

Micro-grids and Distributed Energy Resources

Concept of micro-grid, need & applications of micro-grid, formation of micro-grid, Issues of

interconnection, protection & control of micro-grid. plastic & organic solar cells, thin film solar cells,

variable speed wind generators, fuel cells, micro-turbines, captive power plants, integration of

renewable energy sources.

Power Quality Management in Smart Grid

Power Quality & EMC in Smart Grid, power quality issues of grid connected renewable energy

sources, power quality conditioners for smart grid, web based power quality monitoring, power

quality audit.

III Information and Communication Technology for Smart Grid 13

Advanced metering infrastructure (AMI), home area network (HAN), neighborhood area network

(NAN), wide area network (WAN). Bluetooth, zig-bee, GPS, Wi-Fi, Wi-Max based communication,

wireless mesh network, basics of CLOUD Computing & cyber security for smart grid. Broad-band

over power line (BPL). IP based protocols.

Text Books: Ali Keyhani, Mohammad N. Marwali, Min Dai “Integration of Green and Renewable Energy in

Electric Power Systems”, Wiley Clark W. Gellings, “The Smart Grid: Enabling Energy Efficiency and Demand Response”,CRC Press JanakaEkanayake, Nick Jenkins, KithsiriLiyanage, Jianzhong Wu, Akihiko Yokoyama, “Smart

Grid: Technology and Applications”, Wiley Jean Claude Sabonnadière, NouredineHadjsaïd, “Smart Grids”, Wiley Blackwell Peter S. Fox Penner, “Smart Power: Climate Changes, the Smart Grid, and the Future of Electric Utilities”, Island

Press; 1 edition 8 Jun 2010 References:

Andres Carvallo, John Cooper, “The Advanced Smart Grid: Edge Power Driving Sustainability: 1”, Artech

House Publishers July 2011 James Northcote, Green, Robert G. Wilson “Control and Automation of Electric Power Distribution

Systems (Power Engineering)”, CRC Press MladenKezunovic, Mark G. Adamiak, Alexander P. Apostolov, Jeffrey George Gilbert

“Substation Automation (Power Electronics and Power Systems)”, Springer R. C. Dugan, Mark F. McGranghan, Surya Santoso, H. Wayne Beaty, “Electrical Power System Quality”, 2nd

Edition, McGraw Hill Publication Yang Xiao, “Communication and Networking in Smart Grids”, CRC Press



64

EEE-413: BIO-MEDICAL SIGNAL PROCESSING


Module Content

Teaching

No.

Hours

Biomedical Signals and Images

ECG: Cardiac electrophysiology, relation of electrocardiogram (ECG)

components to cardiac events, clinical applications. Speech Signals: The

source-filter model of speech production, spectrographic analysis of speech.

I Speech Coding: Analysis-synthesis systems, channel vocoders, linear 13

prediction of speech, linear prediction vocoders.

Imaging Modalities: Survey of major modalities for medical imaging:

ultrasound, X-ray, CT, MRI, PET, and SPECT.

Fundamentals of Deterministic Signal and Image Processing

Data Acquisition: Sampling in time, aliasing, interpolation, and quantization.

Digital Filtering: Difference equations, FIR and IIR filters, basic properties of

discrete-time systems, convolution.

DTFT: The discrete-time Fourier transform and its properties. FIR filter

II design using windows. 14

DFT: The discrete Fourier transform and its properties, the fast Fourier

transform (FFT), the overlap-save algorithm, digital filtering of continuous-

time signals.

Sampling Revisited: Sampling and aliasing in time and frequency, spectral

analysis.

Probability and Random Signals

PDFs: Introduction to random variables and probability density functions

(PDFs).Classification: Bayes' rule, detection, statistical classification.

III Estimating PDFs: Practical techniques for estimating PDFs from real data.

13

Random signals I: Time averages, ensemble averages, autocorrelation

functions, cross correlation functions.

Random signals II: Random signals and linear systems, power spectra, cross

spectra, Wiener filters.

References:

D.C.Reddy, “Biomedical Signal processing: Principle and technique,” TMH Gonzalez, R., and R. E. Woods. Digital Image Processing. Prentice-Hall,

3.F.M. Rangayyam, “Biomedical Signal Analysis: A case study approach,Wiley 2002.



65

.

EEE-415: ARTIFICIAL INTELLIGENCE & ITS APPLICATION TO POWER SYSTEM


Module Content

Teaching

No. Hours

Artificial Neural Network

Introduction of ANN, neuron model and network architecture, perceptron

learning rules, signal and weight vector spaces, performance optimization,

I steepest decent algorithm, LMS algorithm, back-propagation algorithm, Chain 15

rule, examples on back-propagation,

Application of ANN on Power System

ANN techniques for voltage control, ANN for power system protection system

Introduction to Fuzzy logic

The case for imprecision, the utility of fuzzy systems, limitations of fuzzy systems,

uncertainty and information, fuzzy sets and membership, chance versus fuzziness

Classical Sets and Fuzzy Sets

Classical sets, operations on classical sets, properties of classical (crisp) sets,

fuzzy sets, fuzzy set operations, properties of fuzzy sets

Classical Relations and Fuzzy Relations

II Cartesian product, crisp relations, cardinality of crisp relations, operations on

15

crisp relations, properties of crisp relations, composition, fuzzy relations,

cardinality of fuzzy relations, operations on fuzzy relations, properties of fuzzy

relations, fuzzy cartesian product and composition, tolerance and equivalence

relations, crisp equivalence relation, crisp tolerance relation, fuzzy tolerance and

equivalence relations, value assignments, cosine amplitude, max–min method

Application of Fuzzy Logic on Power System

Fuzzy logic techniques for voltage control, fuzzy logic for power system

protection system

Evolutionary Computation

Evolutionary algorithms, Genetic algorithms (GA), solution, initial population

genetic operators, fitness function, stopping condition, fitness scaling, rank

scaling, proportional scaling, top scaling, selection, Roulette Wheel selection,

stochastic universal sampling, rank selection, tournament selection, other

III selection methods, mutation, uniform mutation, Gaussian mutation, variable 12

mutation rate, crossover, one-point crossover, two-point crossover, scattered

crossover, intermediate crossover, heuristic crossover, other genetic operators,

eliticism

Application of GA on Power System

GA for voltage control, GA for power system protection system

Text Book: Timothy J. Ross, “Fuzzy Logic with Engineering Applications”, Wiley India. 2.AnupamShukla, RituTiwari, Rahul Kala, “Real Life Applications of Soft Computing”, CRC Press, Taylor & Francis

Group. Martin T Hagan, “Neural Network Design”, China Machine Press.

Reference Book: Kevin M. Passino and Stephen Yurkovich, “Fuzzy Control”, Addison Wesley Longman, Menlo Park, CA, 1998. Kevin Warwick, Arthur Ekwue and Raj Aggarwal, “Artificial Intelligence Techniques in Power Systems”,

Institution of Engineering and Technology, London, United Kingdom.



66

EEE-416: TELEMETRY & DATA TRANSMISSION


Module Content

Teaching

No.

Hours

Telemetry Principles: Introduction, classification, electrical telemetry

systems, PLCC.

Digital Modulation Techniques: Review of PCM, DPCM, DM, methods of binary

I data transmission, data formats, PSK, QPSK, FSK, probability of error, phase 13

ambiguity resolution and differential encoding, error detection, error

correction, error correction codes.

Data Handling System: Block schematic, Sensors, Signal conditioners,

multiplexing, ADC- range and resolution, word Format, frame format, frame

synchronizer codes, R.F. links, X24, RS422, RS423, RS232C interfaces, multi

II terminal configuration, multiplier & concentrator, data modems, data 14

transmission over telephone lines.

Data Acquisition Systems: Bit synchronizers, frame synchronizers, sub-

frame synchronizers, PLL, SCADA.

Remote Control: Communication based processing control systems,

operational security, pipeline control, power system control, Internet based

III tele-metering.

13

Commands: Tone command system, Tone digital command system, ON/OFF

command system.

Satellite Telemetry: General considerations, TT&C services.

References:

Patranabis, D. “Telemetry Principles”, Tata Mc-Graw Hill. Schweber, W.L. “Data Communication” Mc-Graw Hill. Berder, M. “Telemetry Systems”.



67

EEE-417: INDUSTRIAL INSTRUMENTATION


Module

Content Teaching

Hour

Introduction to Industrial Instrumentation:

Basic terminologies: Range, span, settling time dead zone, input impedance.

Dynamic Characteristics: 1st order and second order instruments with step, ramp and sinusoidal

input/ output characteristics.

Strain Gauge: Derivation of gauge factor, strain gauge rosette, unbalanced wheat-stone bridge.

I Load Cell: Link type load cell, beam type load cell, ring type load cell and their sensitivities,

13

Frequency response of link type load cell.

Torque Measurements: Torquecell and its data transmission slip ring and radio telemetry.

Temperature Measurements: Thermistor, resistance temperature detector (its construction,

three wire and four wire method muller bridge), thermocouple, their relative comparison, cold

junction compensation using AD590.

LVDT: Phase compensation, phase sensitive demodulation.

Flow rate Measurements: General consideration of fluid flow rate meters,

laminar flow, reynolds’s number, effect of temperature and pressure on flow rate measurement,

calibration of flow meters.

II Head type: Orifice, venturi, flow nozzle, annubar analysis and calculation.

14

Area flow meter: Rota meter and piston type.

Mass flow meter: Coriolis, thermal, impeller type.

electromagnetic type, ultrasonic type, vortex type, turbo magnetic type.

Pressure Measurement:

Manometers:U-tube, well-type, inclined and dual tube manometers.

Elastic Types: Bourdon gauge, diaphragm type, Bellows element type, pressure and D/P switches,

D/P transmitters.

Electronic Types: Capacitive, piezoresistive and resonator type.

III Vacuum Types: McLeod gauge, thermal conductivity gauge, ionization gauge. 13

Level Measurement:Gauge glass, float, displacers and hydrostatic types ( their construction,

errors and ranges, D/P type sensors and their installation arrangement), capacitive type,

conductivity type magnetic level gauges ultrasonic type, microwave type, radiation type level

gauges,level switches.

References:

AlokBarua, “Fundamentals Of Industrial Instrumentation”, Wiley India Pvt Ltd. S K Singh, “Industrial Instrumentation And Control” 3 Edition, Tata McGraw - Hill Education (2008). K. Krishnamurthy, S Vijayachitra, K Krishnaswamy, “Industrial Instrumentation”, New Age International. D.Patranabis, “Principles of Industrial Instrumentation”, Tata McGraw Hill Publishing Ltd., New Delhi, 1999. Ernest O.Doebelin, “Measurement systems Application and Design, InternationalStudent Edition”, IV Edition,

McGraw Hill Book Company, 1999. R.K.Jain, “Mechanical and Industrial Measurements”, Khanna Publishers, New Delhi, 1999. B.C.Nakra and K.K.Chaudary, “Instrumentation Measurement and Analysis”, TataMcGraw Hill Publishing

Company Ltd., New Delhi, 1985. A.K.Sawhney, “A course in Electrical and Electronic Measurement andInstrumentation”, DhanpatRai and Sons,

New Delhi, 1999. Eckman D.P., ”Industrial Instrumentation” Wiley Eastern Limited, 1990. LiptakB.G.,“Instrument Engineers Handbook (Measurement)”, Chilton Book Co., 1994. P.Holman, “Experimental Methods for Engineers International Student Edition”,McGraw Hill Book Company,

1971. Considine; DouplesM,“Process/Industrial Instruments and Control Handbook”, Magraw Hill.



68

Becwith and Buch , “Mechanical Measurement”Pearson.



69

EEE-420: ENERGY CONSERVATION AND MANAGEMENT


Module

Content Teaching

Hour

Indian Energy Scenario :

Sectoral energy consumption; domestic, industrial and other sectors, energy

needs of growing economy, energy intensity, long term energy scenario,

energy pricing,

I Energy security, energy conservation and its importance, energy strategy for

13

the future, energy conservation Act 2001 and its features.

Basics of Energy- its various forms and conservation :

Electricity basics; Direct current and alternative currents, electricity tariff,

analysis of existing buildings setting up an energy management program

and use management electricity saving techniques

Energy Management & Audit:

Definition, energy audit, need, types of energy audit, energy management

(audit) approach-understanding energy costs, bench marking, energy

performance, matching energy use to requirement, maximizing system

efficiencies, optimizing the input energy requirements, fuel and energy

II substitution, energy audit instruments and metering

14

Financial Management :

Investment-need, appraisal and criteria, financial analysis techniques;

simple, payback period, return on investment, net present value, internal

rate of return, cash flows, risk and sensitivity analysis; financing options,

energy performance contracts and role of energy service companies (ESCOs)

Energy Monitoring and Targeting:

Defining monitoring & targeting, elements of monitoring & targeting, data

and information analysis techniques, production, cumulative sum of

III differences (CUSUM), energy management information systems (EMIS) 13

Energy Efficiency in Utilities and systems:

Energy efficiency pumps and fans, lighting system, motors belts and drives,

refrigeration system.

References:

W. F. Kenny , ‘Energy Conservation In Process Industry AmlanChakrabarti, ‘Energy Engineering and Management’,- Prentice hall India 2011 CB Smith, Energy Management Principles,- Pergamon Press, New York, Bureau of energy efficiency, Hand outs New Delhi . Handbook on Energy Efficiency , TERI, New Delhi, 2009



70

EEE-421: POWER STATION PRACTICE Credits: 04 Semester VII L–T–P: 3–1–0

Text Books:

Module Content

Teaching

No.

Hours

Thermal Power Plant:

Site selection, general layout and operation of plant, detailed description and

use of different parts.

Hydro Electric Plants:

Classifications, location and site selection, detailed description of various

I components, general layout and operation of Plants, brief description of

13

impulse, reaction, Kaplan and Francis turbines, advantages & disadvantages,

hydro-potential in India

Nuclear Power Plant:

Location, site selection, general layout and operation of plant, brief description

of different types of reactors Moderator material, fissile materials, control of

nuclear reactors, disposal of nuclear waste material, shielding.

Gas Turbine Plant:

Operational principle of gas turbine plant & its efficiency, fuels, open and

closed-cycle plants, regeneration, inter-cooling and reheating, role and

applications.

Diesel Plants:

Diesel plant layout, components & their functions, its performance, role and

II applications,

14

Station Layout: Types of substations, bus-bar arrangements, typical layout of

substation.

Power Plant Economics and Tariffs:

Load curve, load duration curve, different factors related to plants and

consumers, cost of electrical energy, depreciation, generation cost, effect of

Load factor on unit cost. Fixed and operating cost of different plants, role of

load diversity in power system economy. Objectives and forms of Tariff.

Economic Operation of Power Systems: Characteristics of steam and hydro-

plants, Constraints in operation, economic load scheduling of thermal plants

neglecting and considering transmission losses, penalty factor, loss coefficients

III and Incremental transmission loss. Hydrothermal Scheduling.

13

ENERGY STORAGE: Pumped hydro, Compressed Air energy storage (CAES),

Flywheel energy storage, Electrochemical energy storage, Thermal energy

storage, Magnetic energy storage, Chemical energy storage, Hydrogen energy

storage.

B.R. Gupta, ‘Generation of Electrical Energy’, S.Chand Publication. Soni, Gupta &Bhatnagar, ‘A text book on Power System Engg.’, DhanpatRai& Co. P.S.R. Murthy, ‘Operation and control of Power System’, BS Publications.

P.K.Nag, ‘Power Plant Engineering’, TMH Publications, 2ndEdition .

References Books: W. D. Stevenson, ‘Elements of Power System Analysis’, McGraw Hill. S. L. Uppal, ‘Electrical Power’, Khanna Publications. Electrical power stations by Car.



71

EEE-461: NON CONVENTIONAL ENERGY RESOURCES


Module Content

Teaching

No. Hours

Introduction

Various non-conventional energy resources- Introduction, availability,

classification, relative merits and demerits.

Solar Cells:

Theory of solar cells. solar cell materials, solar cell power plant, limitations.

I Solar Thermal Energy: 13

Solar radiation flat plate collectors and their materials, applications and

performance, focussing of collectors and their materials, applications and

performance; solar thermal power plants, thermal energy storage for solar

heating and cooling, limitations.

Geothermal Energy:

Resources of geothermal energy, thermodynamics of geo-thermal energy

conversion-electrical conversion, non-electrical conversion, environmental

considerations.

Magneto-hydrodynamics (MHD):

II Principle of working of MHD Power plant, performance and limitations. 14

Fuel Cells:

Principle of working of various types of fuel cells and their working,

performance and limitations.

Thermo-electrical and thermionic Conversions:

Principle of working, performance and limitations.

Wind Energy:

Wnd power and its sources, site selection, criterion, momentum theory,

classification of rotors, concentrations and augments, wind characteristics.

performance and limitations of energy conversion systems.

III Bio-mass:

13

Availability of bio-mass and its conversion theory.

Ocean Thermal Energy Conversion (OTEC):

Availability, theory and working principle, performance and limitations.

Wave and Tidal Wave:

Principle of working, performance and limitations. Waste Recycling Plants

References:

AndraGabdel, "A Handbook for Engineers and Economists". 2. A. Mani , "Handbook of Solar radiation Data for India". 3. Peter Auer, "Advances in Energy System and Technology". Vol. 1 & II Edited byAcademic

Press. 4. F.R. the MITTRE, "Wind Machines" by Energy Resources and Environmental Series. 5. Frank Kreith, "Solar Energy Hand Book".



72

ECE303: ANTENNA & WAVE PROPAGATION

Module No.

Content Teaching

Hours

I

Introduction: Basic Antenna parameters: Patterns, Beam Area ( Beam solid angle), Radiation Intensity, Beam efficiency, Directivity & Gain, Directivity & Resolution, Antenna Apertures, Effective height, Radio Communication link , Retarded Potential, Power Radiation by small Current element. Antenna Arrays: Introduction. Arrays of two isotropic point sources, Non isotropic but similar point sources, Principle of pattern multiplication, Linear arrays of n isotropic point sources of equal amplitude and spacing, Linear broadside arrays with non-uniform Amplitude distributions: General consideration, Example of Dolph-Tchebyscheff (D-T) distribution for an array of eight sources

13

II

Horizontal Antennas above plane ground, Vertical Antenna above plane ground, Folded dipole antenna, Yagi-Uda antenna, The small loop, comparison of Far fields of small loop and short dipole, Radiation resistance of loops, slot antenna, Babinet’s principle of complementary antennas, Impedance of slot antenna, Patch or micro-strip antennas, Horn Antennas, the rectangular Horn antenna, Helical Antenna, Reflector antennas: Flat sheet reflector, corner reflector and design, Paraboloid Reflector, Comparison between parabolic and corner reflector, Broadband and frequency independent antenna: Basics, log periodic Antenna Balun, Balun Types I, II and III and choke baluns, matching stubs.

14

III

Antenna Measurements: Gain, Directional pattern, Phase, polarization Wave Propagation: Electromagnetic or radio waves, modes of propagation, Structure of atmosphere, Ground waves or surface wave propagation, Ground wave attenuation factor A, Sky wave or ionosphere wave propagation, space wave propagation , Propagation of radio waves through ionosphere or expression for the refractive index of the ionosphere, Mechanism of radio waves bending by the ionosphere, critical frequency, virtual height, maximum usable frequency, calculation of MUF, LUF,skip distance, range of space wave propagation or Line of sight, effective earth radius, Duct propagation.

13

Reference Books:

“Antenna for all Applications 3rd edition” Krauss, Marhefka & Ahmed S khan, TMH publication. “Antenna & Wave Propagation” by K.D. Prasad, Satya Publication.

Semester - V L–T–P: 3–1–0 Credits: 04



73

ECE404: WIRELESS COMMUNICATION

Module No.

Contents Teaching

Hours

I

Evolution of mobile radio communication fundamentals. Cellular concepts, Frequency reuse, channel assignment strategies, handoff strategies, interference and system capacity, improving coverage and capacity in cellular systems Large scale path loss: propagation models, reflection, diffraction, scattering, practical link budget design using path loss model.

14

II

Small scale fading &multipath propagation and measurements, Impulse response model and parameters of multipath channels. Small scale Multi path Measurements, Parameters of Mobile Multipath Channels types of small scale fading. Rayleigh & Ricean distribution. Fundamentals of equalization, Equalizers in communication receiver, Survey of equalization techniques, linear equalizer, Algorithms for Adaptive Equalization, Diversity techniques, RAKE receiver.

14

III

Characteristics of speech signals, quantization techniques, vocoders, linear predictive coders, Multiple Access techniques for wireless communications: frequency division multiple access, time division multiple access, spread spectrum multiple access. space division multiple access, Packet radio GSM system for mobile: Services and features, System Architecture, Radio Subsystem Channel types, Frame Structure. CDMA Digital Cellular Standard (IS95):Frequency and Channel specifications, Forward CDMA channel and reverse CDMA channel

14

Text Book:

T.S.Rappaport, “Wireless Communication-Principles And Practice”, Pearson,Second Edition. R. Pandya, “Mobile and Personal Communication System”, PHI.

Reference Books:

Andrea Gold smit h, “Wireless Communications”, Cambridge University press. Andreas F. Molisch, “Wireless Communications”, Wiley Student Edition. S.Haykin&M.Moher, “Modern Wireless Communication”,Pearson,2005

Credits: 04 L–T–P: 3–1–0 Semester VIII



74

ECE403: OPTICAL COMMUNICATION & NETWORKS

Module No.

Contents Teaching

Hours

I

INTRODUCTION: Overview of optical fiber communication- The general system, advantages of optical fiber communications. Optical fiber wave guides- Introduction, Ray theory transmission, Optical fiber Modes and configuration, Mode theory for circular Waveguides, Step Index fibers, Graded Index fibers. TRANSMISSION CHARACTERISTICS OF OPTICAL FIBER: Single mode fibers- Cut off wavelength, Mode Field Diameter, Effective Refractive Index. Fiber Material and its Fabrication Techniques Signal distortion in optical fibers- Attenuation, Absorption, Scattering and Bending losses, Core and Cladding losses. Information capacity determination, Group delay, Attenuation Measurements Techniques, Types of Dispersion - Material dispersion, Wave-guide dispersion, Polarization mode dispersion, Intermodal dispersion. Pulse broadening. Overall fiber dispersion in Multi mode and Single mode fibers, Fiber dispersion measurement techniques, Non linear effects. Optical fiber Connectors: Joints, Couplers and Isolators.

14

II

SOURCES AND DETECTOR: Optical sources- LEDs, Structures, Materials, Quantum efficiency, Power, Modulation, Power bandwidth product. Laser Diodes- Basic concepts, Classifications, Semiconductor injection Laser: Modes, Tunable and fixed laser, Threshold conditions, External quantum efficiency, Laser diode rate equations, resonant frequencies, reliability of LED & ILD Source to fiber power launching - Output patterns, Power coupling, Power launching, Equilibrium Numerical Aperture, Laser diode to fiber coupling. Optical detectors- Physical principles of PIN and APD, Detector response time, Temperature effect on Avalanche gain, Comparison of Photo detectors. FIBER OPTIC RECEIVER AND MEASUREMENT: Optical receiver operation- Fundamental receiver operation, Digital signal transmission, error sources, Receiver configuration, Digital receiver performance, Probability of error, Quantum limit, Analog Receivers Various switching elements, OADM, OXC, CLOS architecture, MEMS, wavelength convertors.

14

III

OPTICAL NETWORKS: Introduction to Optical Networks- Principles and Challenges and its Generation, Characteristics of Optical Fiber in non linear region, Optical Packet Switching, Transmission Basics, Multiplexers & Filters Basic Networks – SONET / SDH – Broadcast – and –select WDM Networks - Wavelength Routed Networks – Non linear effects on Network performance – Performance of WDM + EDFA system – Solitons – Optical CDMA – Ultra High Capacity Networks. OPTICAL SWITCHING: Optical packet switching basis, slotted and unslotted networks, header and packet format, optical burst switching, MEMs based switching, switching with SOAs OTDM, Synchronization, Header Processing, Buffering, Burst Switching.

12

Reference Books: “Optical Fiber Communication” – John M. Senior – Pearson Education – Second Edition. 2007 “Optical Fiber Communication” – Gerd Keiser – McGraw Hill – Third Edition. 2000 R. Ramaswami, & K. N. Sivarajan, “Optical Networks a Practicalperspective”, Morgan Kaufmann Publishers,

3rd Ed. U. Black, “Optical Networks: Third Generation Transport Systems”/ Pearson Educations. Biswanath Mukherjee “Optical WDM Networks” Springer Pub 2006. “Optical Switching Networks”: Mayer & Maritn, Cambrige University Press, 2008

Credits: 04 L–T–P: 3–1–0 Semester VIII



75

EEE-462: INSTRUMENTATION


Module Contents

Teaching

No.

Hours

Generalized measurement systems – Concept, Functional elements

Transducers – Classification, Basic requirements, Selection criteria

Principles of operation of resistive, Inductive, Capacitive, Piezoelectric, Ultrasonic,

I Photoelectric transducers. 14

Signal conditioners and display devices – Bridges, Operational amplifier,

Instrumentation amplifier, Filters, LED, LCD, Nixie tube, Magnetic tape recorder,

Digital recorder.

Measurement of displacement, Force, Acceleration, Velocity and Torque – Strain

Gauge, Load cell, LVDT, Tachometer.

Measurement of flow, Level – Electromagnetic, Ultrasonic flow-meter, Hot wire

II anemometer, Capacitive and Ultrasonic method of measuring level.

14

Measurement of pressure – Vacuum gauge, Bourdon tube

Measurement of temperature – RTD, Thermistor, Thermocouple, Digital

Oxygen analyzer, Measurement of pH, Humidity/Moisture, Gas-chromatography.

Bio-potentials and their Measurement – ECG and EEG, Ultrasonic imaging

Measurement of blood pressure, Body temperature, Dialyser

III Recent improvements – Smart sensor, Fibre optic sensors 12

Introduction of microprocessor based instrumentation

References:

Doeblin: Measurement system, Tata McGraw Hill Nakra: Instrumentation, Measurement and Analysis, TMH. Cromwek, etal: Biomedical Instrumentation and Measurement, PHI Patranabis: Sensors and Transducers, PHI



76

EEE-481: ELECTRIC DRIVES LAB


Module Content Teaching No. Hours

1. To study speed control of separately excited dc motor by varying armature voltage

using single-phase fully controlled bridge converter.

2. To study speed control of separately excited dc motor using single-phase dual

converter (Static Ward-Leonard Control).

3. To study speed control of separately excited dc motor by varying armature voltage

using single phase half controlled bridge converter.

4. To study closed loop control of separately excited dc motor.

5. To study speed control of separately excited dc motor using MOSFET/IGBT chopper.

6. To study speed control of single-phase induction motor using single phase ac voltage

controller.

7. To study speed control of three phase induction motor using three phase ac voltage

controller.

8. To study speed control of three phase induction motor using three phase current

source inverter.

I 9. To study speed control of three phase induction motor using three phase voltage

source inverter.

10. To study speed control of three phase slip ring induction motor using static rotor

resistance control using rectifier and chopper.

Simulation Based Experiments (using MATLAB/ Simulink) 1. To study transient response of separately excited dc motor.

2. To study speed control of separately excited dc motor using single phase full / half

controlled bridge converter in discontinuous and continuous current modes.

3. To study speed control of separately excited dc motor using chopper control in

motoring and braking modes.

4. To study transient response of three phase induction motor.

5. To study speed control of three phase induction motor using (a) constant/V/F

control (b) constant voltage and frequency control.



77

EEE-484: ELECTRICAL INSTRUMENTATION LAB


Module Content

Lab

No. Hours

LIST OF EXPERIMENTS:

Measurement of displacement using LVDT.

Understand the features and hardware structure of an automation

controller.

Create a ladder logic based digital control system with discrete

inputs, outputs.

Create a ladder logic based digital control system with discrete

controls, timers and counters.

Perform a lab to create a velocity algorithm based proportional

integral derivative control (PIDE control).

Perform ratio control and feed forward control with a PIDE loop.

Perform and understand a cascade based control with a PIDE loop.

I Perform position proportional control for a motorized valve 24

through simulation.

Perform and simulate a split range proportional control for

heat/cool cycle.

Create and simulate a ramp controlled temperature control system

with ramp soak control strategy.

Create a Boolean logic and simulate a simple pump control system

in functional block diagram (FBD).

Create a hardware based HMI and create visualization for a pump

control system.

Create a Pc based visualization for a pump control system.

Interfacing an automation controller with a human machine

interface.

Documents

GLA UNIVERSITY, MATHURA (U.P.) INDIAgla.ac.in/public/uploads/filemanager/media/Syllabus_EN.pdf · MBA Open elective 3 1 0 4 4 PRACTICALS 6. EEE-481 Electric Drives Lab 0 0 2 1 2 7