GmbH D IS - DAkkS · Annex to the accreditation certificate D‐IS‐11026‐01‐00 Period of validity: 02.06.2014 to 01.06.2019 Date of issue 23.06.2014 Page 4of 24 DIN EN 15502‐1

This document is a translation. The definitive version is the original German annex to the accreditation certificate.

1/24

Deutsche Akkreditierungsstelle GmbH German Accreditation Body

Annex to the accreditation certificate D‐IS‐11026‐01‐00 according to DIN EN ISO/IEC 17020:2012 Period of validity: 02.06.2014 to 01.06.2019 Date of issue: 23.06.2014

Holder of certificate:

HLK Stuttgart GmbH Pfaffenwaldring 6A, 70569 Stuttgart with its Inspection Body Type A Scope of inspections:

Inspections of new and operating components, installations, processes and systems of building technologies and energetics as well as their production including quality management with regard to thermal, flow, material and control characteristics and determination of their conformance with specific normative requirements or with general requirements on the basis of a professional judgement Abbreviations used: see last page Inspections according to inspection procedure VA 08005 Inspection process 2013‐09 on the basis of following requirements:

Annex to the accreditation certificate D‐IS‐11026‐01‐00

Period of validity: 02.06.2014 to 01.06.2019 Date of issue 23.06.2014 Page 2 of 24

Radiators

DIN EN 442‐2 2003‐12

Radiators and convectors ‐ Part 2: Test methods and rating

DIN EN 442‐3 2003‐12

Radiators and convectors ‐ Part 3: Evaluation of conformity

DIN EN ISO 2409 2013‐06

Paints and varnishes ‐ Cross‐cut test

E DIN EN 16430‐1 2012‐05

Fan assisted radiators, convectors and trench convectors ‐ Part 1: Technical specifications and requirement

E DIN EN 16430‐2 2012‐05

Fan assisted radiators, convectors and trench convectors ‐ Part 2: Test method and rating for thermal output

E DIN EN 16430‐3 2012‐05

Fan assisted radiators, convectors and trench convectors ‐ Part 3: Test method and rating for cooling capacity

DIN 4703‐3 2000‐10

Heating appliances ‐ Part 3: Conversion of the standard thermal output

DIN 4704‐2 1999‐10

Thermal testing of heating appliances ‐ Part 2: Open test booth

DIN 4704‐4 1999‐10

Thermal testing of heating appliances ‐ Part 4: Underfloor heaters with and without fans in the open test booth

DIN 4704‐5 1999‐10

Thermal testing of heating appliances ‐ Part 5: Heating appliances with fans

Heat cost allocators DIN EN 834 1994‐11

Heat cost allocators for the determination of the consumption of room heating radiators ‐ Appliances with electrical energy supply

DIN EN 835 1995‐04

Heat cost allocators for the determination of the consumption of room heating ‐ Appliances without electrical energy supply based on the evaporation principle

AA H201 1993‐12

Prüfung der Eignung eines Regel‐ und Heizkostensystems zur Verbrauchserfassung



Heat generators and domestic water heating systems DIN EN 267 2011‐11

Forced draught burners for liquid fuels

DIN EN 303‐1 2003‐12

Heating boilers ‐ Part 1: Heating boilers with forced draught burners; Terminology, general requirements, testing and marking

DIN EN 303‐2 2003‐12

Heating boilers ‐ Part 2: Heating boilers with forced draught burners; Special requirements for boilers with atomizing oil burners

DIN EN 303‐4 1999‐03

Heating boilers ‐ Part 4: Heating boilers with forced draught burners; Special requirements for boilers with forced draught oil burners with outputs up to 70 kW and a maximum operating pressure of 3 bar

DIN EN 303‐5 2012‐10

Heating boilers ‐ Part 5: Heating boilers for solid fuels, manually and automatically stoked, nominal heat output of up to 500 kW ‐ Terminology, requirements, testing and marking

DIN EN 304 2004‐01

Heating boilers ‐ Test code for heating boilers for atomizing oil burners

DIN EN 483 2000‐06

Gas‐fired central heating boilers; Type C boilers of nominal heat input not exceeding 70 kW

DIN EN 483/A2 2002‐05

Gas‐fired central heating boilers ‐ Type C boilers of nominal heat input not exceeding 70 kW. Amendment A2

DIN EN 483/A2 Ber. 1 2007‐10

Gas‐fired central heating boilers ‐ Type C boilers of nominal heat input not exceeding 70 kW; Corrigenda to DIN EN 483/A2:2002‐05

DIN EN 483/A4 2010‐07

Gas fired central heating boilers ‐ Type C boilers of nominal heat input not exceeding 70 kW

DIN EN 625 1995‐10

Gas‐fired central heating boilers ‐ Specific requirements for the domestic hot water operation of combination boilers of nominal heat input not exceeding 70 kW

DIN EN 12897 2006‐09

Water supply ‐ Specification for indirectly heated unvented (closed) storage water heaters

DIN EN 15034 2007‐01

Heating boilers ‐ Condensing heating boilers for fuel oil

DIN EN 15378 2008‐07

Heating systems in buildings ‐ Inspection of boilers and heating systems



DIN EN 15502‐1 2012‐10

Gas‐fired heating boilers ‐ Part 1: General requirements and tests

DIN EN 15502‐2‐1 2013‐01

Gas‐fired central heating boilers ‐ Part 2‐1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding 1 000 kW

E DIN EN 15502‐2‐2 2012‐10

Gas‐fired central heating boilers ‐ Part 2‐2: Specific standard for type B1 appliances of a nominal heat input not exceeding 70 kW

DIN 4702‐4 1990‐03

Boilers for central heating; boilers for wood, straw and similar fuels; terms requirements, testing

DIN 4702‐8 1990‐03

Central heating boiler; determination of the standard efficiency and the standard emissivity

DIN 4708‐3 1994‐04

Central heat‐water‐installations; rules for testing the efficiency of water‐heaters in dwelling houses

DIN 4753‐1 2011‐11

Water heaters, water heating installations and storage water heaters for drinking water ‐ Part 1: Tanks with a capacity of over 1000 l

DIN 4753‐7 2011‐11

Water heaters, water heating installations and storage water heaters for drinking water ‐ Part 7: Tanks with a capacity of up to 1000 l, requirements relating to manufacture, thermal insulation and corrosion protection

AA Q301 1998‐06

Blendenabstimmung an Gasthermen

Thermostatic radiator valves DIN EN 215‐1 2007‐11

Thermostatic radiator valves; requirements and testing

Floor heating DIN EN 1264‐1 2011‐09

Water based surface embedded heating and cooling systems ‐ Part 1: Definitions and symbols

DIN EN 1264‐2 2013‐03

Water based surface embedded heating and cooling systems ‐ Part 2: Floor heating: Prove methods for the determination of the thermal output using calculation and test methods



DIN EN 1264‐3 2009‐11

Water based surface embedded heating and cooling systems ‐ Part 3: Dimensioning

DIN EN 1264‐4 2009‐11

Water based surface embedded heating and cooling systems ‐ Part 4: Installation

DIN EN 1264‐5 2009‐01

Water based surface embedded heating and cooling systems ‐ Part 5: Heating and cooling surfaces embedded in floors, ceilings and walls ‐ Determination of the thermal output

Ceiling mounted radiant panels and cooling surfaces DIN EN 14037‐2 2003‐08

Ceiling mounted radiant panels supplied with water at temperature below 120 °C ‐ Part 2: Test method for thermal output

DIN EN 14037‐3 2003‐08

Ceiling mounted radiant panels supplied with water at temperature below 120 °C ‐ Part 3: Thermal conversion, rating methods and evaluation of the radiant thermal output

DIN EN 14240 2004‐04

Ventilation for buildings – Chilled ceilings ‐ Testing and rating

DIN EN 14518 2005‐08

Ventilation for buildings ‐ Chilled beams ‐ Testing and rating of passive chilled beams

DIN EN 15116 2008‐07

Ventilation in buildings ‐ Chilled beams ‐ Testing and rating of active chilled beams

VDI 6031 2006‐03

Acceptance test of cooling surfaces for rooms

Ventilation and air‐conditioning technology DIN EN 308 1997‐06

Heat exchangers ‐ Test procedures for establishing performance of air to air and flue gases heat recovery devices

DIN EN 1886 2009‐07

Ventilation for buildings ‐ Air handling units ‐ Mechanical performance

DIN EN 12599 2013‐01

Ventilation for buildings ‐ Test procedures and measurement methods to hand over air conditioning and ventilation systems



DIN EN 13141‐1 2004‐05

Ventilation for buildings ‐ Performance testing of components/ products for residential ventilation ‐ Part 1: Externally and internally mounted air transfer devices

DIN EN 13141‐2 2010‐12

Ventilation for buildings ‐ Performance testing of components /products for residential ventilation ‐ Part 2: Exhaust and supply air terminal devices

DIN EN 13141‐3 2004‐04

Ventilation for buildings ‐ Performance testing of components/ products for residential ventilation ‐ Part 3: Range hoods for residential use

DIN EN 13141‐4 2011‐09

Ventilation for buildings ‐ Performance testing of components/ products for residential ventilation ‐ Part 4: Fans used in residential ventilation systems

DIN EN 13141‐5 2005‐01

Ventilation for buildings ‐ Performance testing of components/ products for residential ventilation ‐ Part 5: Cowls and roof outlet terminal devices

DIN EN 13141‐6 2004‐04

Ventilation for buildings ‐ Performance testing of components/ products for residential ventilation ‐ Part 6: Exhaust ventilation system packages used in a single dwelling

DIN EN 13141‐7 2011‐01

Ventilation for buildings ‐ Performance testing of components/ products for residential ventilation ‐ Part 7: Performance testing of a mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for single family dwellings

DIN EN 13141‐8 2006‐05

Ventilation for buildings ‐ Performance testing of components/ products for residential ventilation ‐ Part 8: Performance testing of un‐ducted mechanical supply and exhaust ventilation units (including heat recovery) for mechanical ventilation systems intended for a single room

DIN EN 13779 2007‐09

Ventilation for non‐residential buildings ‐ Performance requirements for ventilation and room‐conditioning systems

DIN EN 14175‐1 2003‐08

Fume cupboards ‐ Part 1: Vocabulary

DIN EN 14175‐2 2003‐08

Fume cupboards ‐ Part 2: Safety and performance requirements

DIN EN 14175‐3 2004‐03

Fume cupboards ‐ Part 3: Type test methods



DIN EN 14175‐4 2004‐12

Fume cupboards ‐ Part 4: On‐site test methods

DIN EN 14175‐6 2006‐08

Fume cupboards ‐ Part 6: Variable air volume fume cupboards

DIN EN 14511‐1 2012‐01

Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling ‐ Part 1: Terms and definitions

DIN EN 14511‐2 2012‐01

Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling ‐ Part 2: Test conditions

DIN EN 14511‐3 2012‐01

Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling ‐ Part 3: Test methods

DIN EN 14511‐4 2012‐01

Air conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling ‐ Part 4: Requirements

DIN EN 14825 2012‐06

Air conditioners, liquid chilling packages and heat pumps, with electrically driven compressors, for space heating and cooling ‐ Testing and rating at part load conditions and calculation of seasonal performance

DIN EN 15239 2007‐08

Ventilation for buildings ‐ Energy performance of buildings ‐ Guidelines for inspection of ventilation systems

DIN EN 15240 2007‐08

Ventilation for buildings ‐ Energy performance of buildings ‐ Guidelines for inspection of air‐conditioning systems

DIN EN 15251 2012‐12

Indoor environmental input parameters for design and assessment of energy performance of buildings addressing indoor air quality, thermal environment, lighting and acoustics

DIN EN 15727 2010‐10

Ventilation for buildings ‐ Ducts and ductwork components, leakage classification and testing

DIN EN 16147 2011‐04

Heat pumps with electrically driven compressors ‐ Testing and requirements for marking of domestic hot water units



DIN EN 16147 Ber. 1 2012‐06

Heat pumps with electrically driven compressors ‐ Testing and requirements for marking of domestic hot water units. Corrigendum to DIN EN 16147:2011‐04

DIN EN ISO 5801 2011‐11

Industrial fans ‐ Performance testing using standardized airways

DIN EN ISO 7730 2006‐03

Ergonomics of the thermal environment ‐ Analytical determination and interpretation of thermal comfort using calculation of the PMV and PPD indices and local thermal comfort criteria

DIN 1946‐4 2008‐12

Ventilation and air conditioning ‐ Part 4: Ventilation in buildings and rooms of health care

DIN 8900‐6 1987‐12

Heat pumps; heat pump units equipment with electrically driven compressors, methods of measurement for installed water/water, air/water and brine/water heat pumps

DIN 12924‐3 2011‐01

Laboratory furniture ‐ Fume cupboards ‐ Part 3: Opposite‐sided sash fume cupboards

DIN 12924‐4 2012‐02

Laboratory furniture ‐ Fume cupboards ‐ Part 4: Fume cupboards for pharmacies

DIN 18017‐3 2009‐09

Ventilation of bathrooms and WCs without outside windows ‐ Part 3: Ventilation by fans

NEN 5138 2004‐12

Heat recovery in buildings ‐ Determination method for the energetic efficiency of heat recovery units for individual ventilation systems

AA R701 1997‐12

Messungen mit der Schadstofferfassungseinrichtung

Sanitary and piping systems DIN EN 31 2011‐11

Wash basins ‐ Connecting dimensions

DIN EN 33 2011‐11

WC pans and WC suites ‐ Connecting dimensions

DIN EN 35 2000‐04

Pedestal and wall‐hung bidets with over‐rim supply ‐ Connecting dimensions

DIN EN 36 1991‐01

Wall‐hung bidets with over‐rim supply ‐ Connecting dimensions



DIN EN 80 2002‐02

Wall‐hung urinals ‐ Connecting dimensions

DIN EN 232 2013‐01

Baths ‐ Connecting dimensions

DIN EN 251 2013‐01

Shower trays ‐ Connecting dimensions

DIN EN 274‐1 2002‐05

Waste fittings for sanitary appliances ‐ Part 1: Requirements

DIN EN 274‐2 2002‐05

Waste fittings for sanitary appliances ‐ Part 2: Test methods

DIN EN 274‐3 2002‐05

Waste fittings for sanitary appliances ‐ Part 3: Quality control

DIN EN 295‐1 2013‐05

Vitrified clay pipe systems for drains and sewers ‐ Part 1: Requirements for pipes, fittings and joints

DIN EN 295‐2 2013‐05

Vitrified clay pipe systems for drains and sewers ‐ Part 2: Evaluation of conformity and sampling

DIN EN 295‐3 2012‐03

Vitrified clay pipe systems for drains and sewers ‐ Part 3: Test methods

DIN EN 295‐4 2013‐05

Vitrified clay pipe systems for drains and sewers ‐ Part 4: Requirements for adaptors, connectors and flexible couplings

DIN EN 295‐5 2013‐05

Vitrified clay pipe systems for drains and sewers ‐ Part 5: Requirements for perforated pipes and fittings

DIN EN 295‐6 2013‐05

Vitrified clay pipe systems for drains and sewers ‐ Part 6: Requirements for components of manholes and inspection chambers

DIN EN 295‐7 2013‐05

Vitrified clay pipe systems for drains and sewers ‐ Part 7: Requirements for pipes and joints for pipe jacking

DIN EN 476 2011‐04

General requirements for components used in drains and sewers

DIN EN 545 2011‐09

Ductile iron pipes, fittings, accessories and their joints for water pipelines ‐ Requirements and test methods



DIN EN 588‐1 1996‐11

Fibre‐cement pipes for sewers and drains ‐ Part 1: Pipes, joints and fittings for gravity systems

DIN EN 588‐2 2002‐05

Fibre cement pipes for drains and sewers ‐ Part 2: Manholes and inspection chambers

DIN EN 598 2009‐10

Ductile iron pipes, fittings, accessories and their joints for sewerage applications ‐ Requirements and test methods

DIN EN 681‐1 2006‐11

Elastomeric seals ‐ Material requirements for pipe joint seals used in water and drainage applications ‐ Part 1: Vulcanized rubber

DIN EN 681‐2 2006‐11

Elastomeric seals ‐ Material requirements for pipe joint seals used in water and drainage applications ‐ Part 2: Thermoplastic elastomers

DIN EN 681‐3 2006‐11

Elastomeric seals ‐ Material requirements for pipe joint seals used in water and drainage applications ‐ Part 3: Cellular materials of vulcanized rubber

DIN EN 681‐4 2006‐11

Elastomeric seals ‐ Material requirements for pipe joint seals used in water and drainage applications ‐ Part 4: Cast polyurethane sealing elements

DIN EN 695 2005‐11

Kitchen sinks ‐ Connecting dimensions

DIN EN 705 1994‐08

Plastics piping systems ‐ Glass‐reinforced thermosetting plastics (GRP) pipes and fittings ‐ Methods for regression analyses and their use

DIN EN 727 1995‐01

Plastics piping and ducting systems ‐ Thermoplastics pipes and fittings ‐ Determination of Vicat softening temperature (VST)

DIN EN 728 1997‐03

Plastics piping and ducting systems ‐ Polyolefin pipes and fittings ‐ Determination of oxidation induction time

DIN EN 877 2010‐01

Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings ‐ Requirements, test methods and quality assurance

DIN EN 997 2012‐05

WC pans and WC suites with integral trap



DIN EN 1120 1996‐07

Plastics piping systems ‐ Glass‐reinforced thermosetting plastics (GRP) pipes and fittings ‐ Determination of the resistance to chemical attack from the inside of a section in a deflected condition

DIN EN 1123‐1 2004‐12

Pipes and fittings of longitudinally welded hot‐dip galvanized steel pipes with spigot and socket for waste water systems ‐ Part 1: Requirements, testing, quality control

DIN EN 1123‐2 2007‐12

Pipes and fittings of longitudinally welded hot‐dip galvanized steel tube with spigot and socket for waste water systems ‐ Part 2: Dimensions

DIN EN 1124‐1 2004‐12

Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems ‐ Part 1: Requirements, testing, quality control

DIN EN 1124‐1 Ber. 1 2006‐01

Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems ‐ Part 1: Requirements, testing, quality control. Corrigenda to DIN EN 1124‐1:2004‐12

DIN EN 1124‐2 2008‐02

Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems ‐ Part 2: System S ‐ Dimensions

DIN EN 1124‐3 2009‐02

Pipes and fittings of longitudinally welded stainless steel pipes with spigot and socket for waste water systems ‐ Part 3: System X ‐ Dimensions

DIN EN 1226 1996‐08

Plastics piping systems ‐ Glass‐reinforced thermosetting plastics (GRP) pipes ‐ Test method to prove the resistance to initial ring deflection

DIN EN 1228 1996‐08

Plastics piping systems ‐ Glass‐reinforced thermosetting plastics (GRP) pipes ‐ Determination of initial specific ring stiffness

DIN EN 1277 2004‐03

Plastics piping systems ‐ Thermoplastics piping systems for buried non‐pressure applications ‐ Test methods for leaktightness of elastomeric sealing ring type joints

DIN EN 1329‐1 1999‐12

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure ‐ Unplasticized poly(vinyl chloride) (PVC‐U) ‐ Part 1: Specifications for pipes, fittings and the system



DIN CEN/TS 1329‐2 2012‐09

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure ‐ Unplasticized poly(vinyl chloride) (PVC‐U) ‐ Part 2: Guidance for the assessment of conformity

DIN EN 1393 1996‐12

Plastics piping systems ‐ Glass‐reinforced thermosetting plastics (GRP) pipes; Determination of initial longitudinal tensile properties

DIN EN 1401‐1 2009‐07

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Unplasticized poly(vinyl chloride) (PVC‐U) ‐ Part 1: Specifications for pipes, fittings and the system

DIN CEN/TS 1401‐2 2012‐09

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Unplasticized poly(vinyl chloride) (PVC‐U) ‐ Part 2: Guidance for assessment of conformity

DIN V EN V 1401‐3 2001‐10

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Unplasticized poly(vinyl chloride) (PVC‐U) ‐ Part 3: Guidance for installation

DIN EN 1453‐1 2000‐03

Plastics piping systems with structured‐wall pipes for soil and waste discharge (low and high temperature) inside buildings ‐ Unplasticized poly(vinyl chloride) (PVC‐U) ‐ Part 1: Specifications for pipes and the system

DIN V ENV 1453‐2 2001‐04

Plastics piping systems with structured wall pipes for soil and waste discharge (low and high temperature) inside buildings ‐ Unplasticized poly(vinyl chloride) (PVC‐U) ‐ Part 2: Guidance for the assessment of conformity

DIN EN 1451‐1 1999‐03

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure ‐ Polypropylene (PP) ‐ Part 1: Specifications for pipes, fittings and the system

DIN CEN/TS 1451‐2 2012‐05

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure ‐ Polypropylene (PP) ‐ Part 2: Guidance for the assessment of conformity

DIN EN 1455‐1 1999‐12

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure ‐ Acrylonitrile‐butadiene‐styrene (ABS) ‐ Part 1: Specification for pipes, fittings and the system



DIN CEN/TS 1455‐2 2012‐09

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure ‐ Acrylonitrile‐butadiene‐styrene (ABS) ‐ Part 2: Guidance for the assessment of conformity

DIN EN 1519‐1 2000‐01

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure ‐ Polyethylene (PE) ‐ Part 1: Specifications for pipes, fittings and the system

DIN CEN/TS 1519‐2 2012‐05

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure ‐ Polyethylene (PE) ‐ Part 2: Guidance for the assessment of conformity

DIN EN 1565‐1 1999‐12

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure ‐ Styrene copolymer blends (SAN+PVC) ‐ Part 1: Specifications for pipes, fittings and the system

DIN CEN/TS 1565‐2 2012‐09

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure ‐ Styrene‐copolymer blends (SAN+PVC) ‐ Part 2: Guidance for the assessment of conformity

DIN EN 1566‐1 1999‐12

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure ‐ Chlorinated poly(vinyl chloride) (PVC‐C) ‐ Part 1: Specifications for pipes, fittings and the system

DIN CEN/TS 1566‐2 2012‐09

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure ‐ Chlorinated poly(vinyl chloride) (PVC‐C) ‐ Part 2: Guidance for the assessment of conformity

DIN EN 1852‐1 2009‐07

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Polypropylene (PP) ‐ Part 1: Specifications for pipes, fittings and the system

DIN CEN/TS 1852‐2 2009‐08

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Polypropylene (PP) ‐ Part 2: Guidance for the assessment of conformity

DIN CEN/TS 1852‐3 2005‐08

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Polypropylene (PP) ‐ Part 3: Guidance for installation

DIN EN 1916 2003‐04

Concrete pipes and fittings, unreinforced, steel fibre and reinforced



DIN EN 12293 1999‐09

Plastics piping systems ‐ Thermoplastics pipes and fittings for hot and cold water ‐ Test method for the resistance of mounted assemblies to temperature cycling

DIN EN 12294 1999‐10

Plastics piping systems ‐ Systems for hot and cold water ‐ Test method for leaktightness under vacuum

DIN EN 12295 1999‐10

Plastics piping systems ‐ Thermoplastics pipes and associated fittings for hot and cold water ‐ Test methods for resistance of joints to pressure cycling

DIN EN 12666‐1 2011‐11

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Polyethylene (PE) ‐ Part 1: Specifications for pipes, fittings and the system

DIN CEN/TS 12666‐2 2012‐11

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Polyethylene (PE) ‐ Part 2: Guidance for the assessment of conformity

DIN EN 12763 2000‐10

Fibre‐cement pipes and fittings for discharge systems for buildings ‐ Dimensions and technical terms of delivery

DIN EN 13407 2006‐12

Wall‐hung urinals ‐ Functional requirements and test methods

DIN EN 13476‐1 2007‐08

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Structured‐wall piping systems of unplasticized poly(vinyl chloride) (PVC‐U), polypropylene (PP) and polyethylene (PE) ‐ Part 1: General requirements and performance characteristics

DIN EN 13476‐2 2007‐08

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Structured‐wall piping systems of unplasticized poly(vinyl chloride) (PVC‐U), polypropylene (PP) and polyethylene (PE) ‐ Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A

DIN EN 13476‐3 2009‐04

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Structured‐wall piping systems of unplasticized poly(vinyl chloride) (PVC‐U), polypropylene (PP) and polyethylene (PE) ‐ Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B



DIN CEN/TS 13476‐4 2013‐07

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Structured‐wall piping systems of unplasticized poly(vinyl chloride) (PVC‐U), polypropylene (PP) and polyethylene (PE) ‐ Part 4: Guidance for the assessment of conformity

DIN EN 14055 2011‐02

WC and urinal flushing cisterns

DIN EN 14124 2005‐02

Inlet valves for flushing cisterns with internal overflow

DIN EN 14364 2013‐05

Plastics piping systems for drainage and sewerage with or without pressure ‐ Glass‐reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) ‐ Specifications for pipes, fittings and joints

DIN EN 14528 2007‐07

Bidets ‐ Functional requirements and test methods

DIN EN 14688 2007‐02

Sanitary appliances ‐ Wash basins ‐ Functional requirements and test methods

DIN EN 14758‐1 2012‐05

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Polypropylene with mineral modifiers (PP‐MD) ‐ Part 1: Specifications for pipes, fittings and the system

DIN CEN/TS 14758‐2 2007‐10

Plastics piping systems for non‐pressure underground drainage and sewerage ‐ Polypropylene with mineral modifier(s) (PP‐MD) ‐ Part 2: Guidance for the assessment of conformity

DIN CEN/TS 14758‐3 2006‐08

Plastics piping systems for non‐pressure underground drainage and sewerage – Polypropylene with mineral modifier(s) (PP‐MD) ‐ Part 3: Guidance for installation

DIN EN ISO 105‐B02 2013‐09

Textiles ‐ Tests for colour fastness ‐ Part B02: Colour fastness to artificial light: Xenon arc fading lamp test (ISO 105‐B02:2013)

DIN EN ISO 306 2004‐10

Plastics ‐ Thermoplastic materials ‐ Determination of Vicat softening temperature (VST)

DIN EN ISO 527‐1 2012‐06

Plastics ‐ Determination of tensile properties ‐ Part 1: General principles

DIN EN ISO 527‐2 2012‐06

Plastics ‐ Determination of tensile properties ‐ Part 2: Test conditions for moulding and extrusion plastics



DIN EN ISO 527‐3 2003‐07

Plastics ‐ Determination of tensile properties ‐ Part 3: Test conditions for films and sheets

DIN EN ISO 527‐4 1997‐07

Plastics ‐ Determination of tensile properties ‐ Part 4: Test conditions for isotropic and anisotropic fibre‐reinforced plastic composites

DIN EN ISO 527‐5 2010‐01

Plastics ‐ Determination of tensile properties ‐ Part 5: Test conditions for unidirectional fibre‐reinforced plastic composites

DIN EN ISO 580 2005‐05

Plastics piping and ducting systems ‐ Injection‐moulded thermoplastics fittings ‐ Methods for visually assessing the effects of heating

DIN EN ISO 868 2003‐10

Plastics and ebonite ‐ Determination of indentation hardness by means of a durometer (Shore hardness)

DIN EN ISO 1133‐1 2012‐03

Plastics ‐ Determination of the melt mass‐flow rate (MFR) and melt volume‐flow rate (MVR) of thermoplastics ‐ Part 1: Standard method

DIN EN ISO 1133‐2 2012‐03

Plastics ‐ Determination of the melt mass‐flow rate (MFR) and melt volume‐flow rate (MVR) of thermoplastics ‐ Part 2: Method for materials sensitive to time‐temperature history and/or moisture

DIN EN ISO 1167‐1 2006‐05

Thermoplastics pipes, fittings and assemblies for the conveyance of fluids ‐ Determination of the resistance to internal pressure ‐ Part 1: General method

DIN EN ISO 1461 2009‐10

Hot dip galvanized coatings on fabricated iron and steel articles ‐ Specifications and test methods

DIN EN ISO 2505 2005‐08

Thermoplastics pipes ‐ Longitudinal reversion ‐ Test methods and parameters

DIN EN ISO 3126 2005‐05

Plastics piping systems ‐ Plastics components ‐ Determination of dimensions

DIN EN ISO 4624 2003‐08

Paints and varnishes ‐ Pull‐off test for adhesion

DIN EN ISO 4892‐1 2001‐09

Plastics ‐ Methods of exposure to laboratory light sources ‐ Part 1: General guidance



DIN EN ISO 4892‐2 2013‐06

Plastics ‐ Methods of exposure to laboratory light sources ‐ Part 2: Xenon‐arc lamps

DIN EN ISO 4892‐3 2006‐05

Plastics ‐ Methods of exposure to laboratory light sources ‐ Part 3: Fluorescent UV lamps

DIN EN ISO 6259‐1 2002‐02

Thermoplastics pipes ‐ Determination of tensile properties ‐ Part 1: General test method

DIN EN ISO 6506‐1 2006‐03

Metallic materials ‐ Brinell hardness test ‐ Part 1: Test method

DIN EN ISO 9969 2008‐03

Thermoplastics pipes ‐ Determination of ring stiffness

DIN EN ISO 11357‐1 2010‐03

Plastics ‐ Differential scanning calorimetry (DSC) ‐ Part 1: General principles

DIN EN ISO 11357‐3 2013‐04

Plastics ‐ Differential scanning calorimetry (DSC) ‐ Part 3: Determination of temperature and enthalpy of melting and crystallization

DIN EN ISO 11357‐4 2013‐04

Plastics ‐ Differential scanning calorimetry (DSC) ‐ Part 4: Determination of specific heat capacity

DIN EN ISO 11357‐6 2013‐04

Plastics ‐ Differential scanning calorimetry (DSC) ‐ Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)

DIN EN ISO 11358 1997‐11

Kunststoffe ‐ Thermogravimetrie (TG) von Polymeren ‐ Allgemeine Grundlagen

DIN EN ISO 15874‐1 2013‐06

Plastics piping systems for hot and cold water installations ‐ Polypropylene (PP) ‐ Part 1: General

DIN EN ISO 15874‐2 2013‐06

Plastics piping systems for hot and cold water installations ‐ Polypropylene (PP) ‐ Part 2: Pipes

DIN EN ISO 15874‐3 2013‐06

Plastics piping systems for hot and cold water installations ‐ Polypropylene (PP) ‐ Part 3: Fittings

DIN EN ISO 15874‐5 2013‐06

Plastics piping systems for hot and cold water installations ‐ Polypropylene (PP) ‐ Part 5: Fitness for purpose of the system



DIN ISO/TS 15874‐7 2004‐03

Plastics piping systems for hot and cold water installations ‐ Polypropylene (PP) ‐ Part 7: Guidance for the assessment of conformity

DIN EN ISO 15875‐1 2004‐03

Plastics piping systems for hot and cold water installations ‐ Crosslinked polyethylene (PE‐X) ‐ Part 1: General

DIN EN ISO 15875‐1/A1 2007‐09

Plastics piping systems for hot and cold water installations ‐ Crosslinked polyethylene (PE‐X) ‐ Part 1: General ‐ Amendment 1

DIN EN ISO 15875‐2 2004‐03

Plastics piping systems for hot and cold water installations ‐ Crosslinked polyethylene (PE‐X) ‐ Part 2: Pipes

DIN EN ISO 15875‐2/A1 2007‐09

Plastics piping systems for hot and cold water installations ‐ Crosslinked polyethylene (PE‐X) ‐ Part 2: Pipes ‐ Amendment 1

DIN EN ISO 15875‐3 2004‐03

Plastics piping systems for hot and cold water installations ‐ Crosslinked polyethylene (PE‐X) ‐ Part 3: Fittings

DIN EN ISO 15875‐5 2004‐03

Plastics piping systems for hot and cold water installations ‐ Crosslinked polyethylene (PE‐X) ‐ Part 5: Fitness for purpose of the system

DIN ISO/TS 15875‐7 2004‐03

Plastics piping systems for hot and cold water installations ‐ Crosslinked polyethylene (PE‐X) ‐ Part 7: Guidance for the assessment of conformity

DIN EN ISO 15876‐1 2004‐03

Plastics piping systems for hot and cold water installations ‐ Polybutylene (PB) ‐ Part 1: General

DIN EN ISO 15876‐1/A1 2007‐09

Plastics piping systems for hot and cold water installations ‐ Polybutylene (PB) ‐ Part 1: General ‐ Amendment 1

DIN EN ISO 15876‐2 2004‐03

Plastics piping systems for hot and cold water installations ‐ Polybutylene (PB) ‐ Part 2: Pipes

DIN EN ISO 15876‐2/A1 2007‐09

Plastics piping systems for hot and cold water installations ‐ Polybutylene (PB) ‐ Part 2: Pipes ‐ Amendment 1

DIN EN ISO 15876‐3 2004‐03

Plastics piping systems for hot and cold water installations ‐ Polybutylene (PB) ‐ Part 3: Fittings

DIN EN ISO 15876‐5 2004‐03

Plastics piping systems for hot and cold water installations ‐ Polybutylene (PB) ‐ Part 5: Fitness for purpose of the system



DIN ISO/TS 15876‐7 2004‐03

Plastics piping systems for hot and cold water installations ‐ Polybutylene (PB) ‐ Part 7: Guidance for the assessment of conformity

DIN EN ISO 15877‐1 2011‐03

Plastics piping systems for hot and cold water installations ‐ Chlorinated poly(vinyl chloride) (PVC‐C) ‐ Part 1: General

DIN EN ISO 15877‐2 2011‐03

Plastics piping systems for hot and cold water installations ‐ Chlorinated poly(vinyl chloride) (PVC‐C) ‐ Part 2: Pipes

DIN EN ISO 15877‐3 2011‐03

Plastics piping systems for hot and cold water installations ‐ Chlorinated poly(vinyl chloride) (PVC‐C) ‐ Part 3: Fittings

DIN EN ISO 15877‐5 2011‐03

Plastics piping systems for hot and cold water installations ‐ Chlorinated poly(vinyl chloride) (PVC‐C) ‐ Part 5: Fitness for purpose of the system

DIN ISO/TS 15877‐7 2010‐02

Plastics piping systems for hot and cold water installations ‐ Chlorinated poly(vinyl chloride) (PVC‐C) ‐ Part 7: Guidance for the assessment of conformity

DIN EN ISO 21003‐1 2008‐11

Multilayer piping systems for hot and cold water installations inside buildings ‐ Part 1: General

DIN EN ISO 21003‐1 Ber 1 2010‐01

Multilayer piping systems for hot and cold water installations inside buildings ‐ Part 1: General (ISO 21003‐1:2008); Corrigendum to DIN EN ISO 21003‐1:2008‐11

DIN EN ISO 21003‐2 2011‐07

Multilayer piping systems for hot and cold water installations inside buildings ‐ Part 2: Pipes

DIN EN ISO 21003‐3 2008‐11

Multilayer piping systems for hot and cold water installations inside buildings ‐ Part 3: Fittings

DIN EN ISO 21003‐5 2008‐11

Multilayer piping systems for hot and cold water installations inside buildings ‐ Part 5: Fitness for purpose of the system

DIN CEN ISO/TS 21003‐7 2010‐12

Multilayer piping systems for hot and cold water installations inside buildings ‐ Part 7: Guidance for the assessment of conformity

DIN EN ISO 22391‐1 2010‐04

Plastics piping systems for hot and cold water installations ‐ Polyethylene of raised temperature resistance (PE‐RT) ‐ Part 1: General

DIN EN ISO 22391‐2 2010‐04

Plastics piping systems for hot and cold water installations ‐ Polyethylene of raised temperature resistance (PE‐RT) ‐ Part 2: Pipes



DIN EN ISO 22391‐3 2010‐04

Plastics piping systems for hot and cold water installations ‐ Polyethylene of raised temperature resistance (PE‐RT) ‐ Part 3: Fittings

DIN EN ISO 22391‐5 2010‐04

Plastics piping systems for hot and cold water installations ‐ Polyethylene of raised temperature resistance (PE‐RT) ‐ Part 5: Fitness for purpose of the system

DIN CEN ISO/TS 22391‐7 2012‐03

Plastics piping systems for hot and cold water installations ‐ Polyethylene of raised temperature resistance (PE‐RT) ‐ Part 7: Guidance for the assessment of conformity

DIN ISO 48 2009‐10

Rubber, vulcanized or thermoplastic ‐ Determination of hardness (hardness between 10 IRHD and 100 IRHD)

DIN ISO 815‐1 2010‐09

Rubber, vulcanized or thermoplastic ‐ Determination of compression set ‐ Part 1: At ambient or elevated temperatures

DIN ISO 1431‐1 2011‐05

Rubber, vulcanized or thermoplastic ‐ Resistance to ozone cracking ‐ Part 1: Static and dynamic strain testing

DIN ISO 1817 2008‐08

Rubber, vulcanized ‐ Determination of the effect of liquids

DIN ISO 2285 2010‐07

Rubber, vulcanized or thermoplastic ‐ Determination of tension set under constant elongation, and of tension set, elongation and creep under constant tensile load

DIN ISO 3302 1999‐10

Rubber ‐ Tolerances for products ‐ Part 1: Dimensional tolerances

DIN ISO 3384 2008‐07

Rubber, vulcanized or thermoplastic ‐ Determination of stress relaxation in compression at ambient and at elevated temperatures

DIN ISO 7619‐1 2012‐02

Rubber, vulcanized or thermoplastic ‐ Determination of indentation hardness ‐ Part 1: Durometer method (Shore hardness)

ISO 188 2011‐10

Rubber, vulcanized or thermoplastic ‐ Accelerated ageing and heat resistance tests.

ISO 559 1991‐02

Steel tubes for water and sewage



ISO 3306 1985‐11

Plain end as‐welded and sized precision steel tubes; Technical conditions for delivery

ISO 3387 2012‐07

Rubber. Determination of crystallization effects by hardness measurements

ISO 6505 2005‐10

Rubber, vulcanized or thermoplastic ‐ Determination of tendency to adhere to and corrode metals

ISO 6594 2006‐03

Cast iron drainage pipes and fittings ‐ Spigot series

ISO 6964 1986‐12

Polyolefin pipes and fittings ‐ Determination of carbon black content by calcination and pyrolysis ‐ Test method and basic specification

ISO 8361‐1 1991‐09

Thermoplastics pipes and fittings ‐ water absorption ‐ part 1: general test method

ISO 8361‐2 1991‐09

Thermoplastics pipes and fittings; water absorption ‐ part 2: test conditions for unplasticized poly(vinyl chloride) (PVC‐U) pipes and fittings

ISO 8361‐3 1991‐09

Thermoplastics pipes and fittings ‐ water absorption ‐ part 3: test conditions for acrylonitrile/butadiene/styrene (ABS) pipes and fittings

ISO 9924‐1 2000‐12

Rubber and rubber products ‐ Determination of the composition of vulcanizates and uncured compounds by thermogravimetry ‐ Part 1: Butadiene, ethylene‐propylene copolymer and terpolymer, isobutene‐isoprene, isoprene and styrene‐butadiene rubbers

ISO 9924‐2 2000‐09

Rubber and rubber products ‐ Determination of the composition of vulcanizates and uncured compounds by thermogravimetry ‐ Part 2: Acrylonitrile‐butadiene and halobutyl rubbers

ISO 9924‐2 AMD 1 2012‐07

Rubber and rubber products ‐ Determination of the composition of vulcanizates and uncured compounds by thermogravimetry ‐ Part 2: Acrylonitrile‐butadiene and halobutyl rubbers; Amendment 1

ISO 9924‐3 2009‐03

Rubber and rubber products ‐ Determination of the composition of vulcanizates and uncured compounds by thermogravimetry ‐ Part 3: Hydrocarbon rubbers, halogenated rubbers and polysiloxane rubbers after extraction



ISO 10358 1993‐06

Plastics pipes and fittings ‐ combined chemical‐resistance classification table

ISO 10468 2003‐12

Glass‐reinforced thermosetting plastics (GRP) pipes ‐ Determination of the long‐term specific ring creep stiffness under wet conditions and calculation of the wet creep factor

ISO 10468 AMD 1 2010‐09

Glass‐reinforced thermosetting plastics (GRP) pipes ‐ Determination of the long‐term specific ring creep stiffness under wet conditions and calculation of the wet creep factor; Amendment 1

ISO 10471 2003‐12

Glass‐reinforced thermosetting plastics (GRP) pipes ‐ Determination of the long‐term ultimate bending strain and the long‐term ultimate relative ring deflection under wet conditions

ISO 10471 AMD 1 2010‐09

Glass‐reinforced thermosetting plastics (GRP) pipes ‐ Determination of the long‐term ultimate bending strain and the long‐term ultimate relative ring deflection under wet conditions; Amendment 1

ISO 14828 2003‐12

Glass‐reinforced thermosetting plastics (GRP) pipes ‐ Determination of the long‐term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor

ISO 14828 AMD 1 2010‐09

Glass‐reinforced thermosetting plastics (GRP) pipes ‐ Determination of the long‐term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor; Amendment 1

DIN 4724 2001‐04

Plastic piping systems for warm water floor heating systems and radiator pipe connecting ‐ Crosslinked polyethylene of medium density (PE‐MDX)

DIN 4726 2008‐10

Warm water surface heating systems and radiator connecting systems ‐ Plastics piping systems and multilayer piping systems

DIN 16833 2009‐09

Polyethylene pipes of raised temperature resistance (PE‐RT) ‐ PE‐RT Type I and PE‐RT Type II ‐ General quality requirements, testing

DIN 16894 2011‐04

Pipes of crosslinked medium density polyethylene (PE‐MDX) ‐ General quality requirements and testing

DIN 16895 2011‐04

Crosslinked medium density polyethylene (PE‐MDX) pipes ‐ Dimensions



DIN 51006 2005‐07

Thermal analysis (TA) ‐ Thermogravimetry (TG) ‐ Principles

DIN 53765 1994‐03

Testing of plastics and elastomeres ‐ thermal analysis; DSC‐method

DVGW W 534 2004‐05

Pipe connectors and pipe joints in drinking water installation

DVGW W 542 2009‐08

Compound pipes in the drinking water installations ‐ requirements and testing

DVS 2203‐1 2003‐01

Testing of welded joints of thermoplastics sheet and pipes ‐ Test methods ‐ Requirements

DVS 2203‐1 Beiblatt 1 2010‐08

Testing of welded joints between panels and pipes made of thermoplastics ‐ Requirements in the tensile test ‐ Short‐time tensile welding factor fz

DVS 2203‐1 Beiblatt 2 2006‐04

Testing of welded joints between panels and pipes made of thermoplastics ‐ Requirements in the tensile creep test (Tensile creep welding factor fs)

DVS 2203‐1 Beiblatt 3 2012‐06

Testing of welded joints of thermoplastics sheet and pipes ‐ Requirements ‐ Technological bend test ‐ Bend angle/ram displacement

DVS 2203‐1 Beiblatt 4 2008‐11

Testing of welded joints between panels and pipes made of thermoplastics ‐ Requirements on shear and peeling tests for sleeve welding with an incorporated electric heating element (HM) and heated tool sleeve welding (HD) on pipes and fittings

DVS 2203‐2 2010‐08

Testing of welded joints between panels and pipes made of thermoplastics ‐ Tensile test

DVS 2203‐3 2011‐04

Testing of welded joints between panels and pipes made of thermoplastics ‐ Tensile impact test

DVS 2203‐5 1999‐08

Testing of welded joints of thermoplastics plates and tubes ‐ Technological bend test

Qplus Richtlinie R 592011 2007‐04

Dichtungen




Entwässerungssysteme


Qualitätssicherung in der Liegenschaftsentwässerung Korrosionsschutz für Rohre und Formstücke aus Stahl und sinngemäss anderen Werkstoffen

Qplus Richtlinie R 592014/1a 2013‐02

Klosetts und Spülkästen Anforderungen und Prüfverfahren

Qplus Richtlinie R 592014/1b 2013‐02

Urinale Anforderungen und Prüfverfahren

Qplus Richtlinie R 592014/1c 2013‐02

Waschtische Anforderungen und Prüfverfahren

Qplus Richtlinie R 592014/1d 2013‐02

Bidets Anforderungen und Prüfverfahren

Qplus Richtlinie R 592014/2 2009‐03

Qualitätssicherung in der Liegenschaftsentwässerung Ablaufgarnituren, Prüfrichtlinie

Qplus Richtlinie R 592014/3 2008‐02

Qualitätssicherung in der Liegenschaftsentwässerung Einläufe und Abläufe für Boden und Regenwasser, Prüfrichtlinie

Abbreviations used: AA xx In‐house method MSR Measurement and control DVGW Deutscher Verein des Gas‐ und Wasserfaches e.V. DVS Deutscher Verband für Schweißen und verwandte Verfahren e.V. NEN Netherland Standard Qplus Verein nach Schweizer Recht VDI Verein Deutscher Ingenieure e.V.

Documents

GmbH D IS - DAkkS · Annex to the accreditation certificate D‐IS‐11026‐01‐00 Period of validity: 02.06.2014 to 01.06.2019 Date of issue 23.06.2014 Page 4of 24 DIN EN 15502‐1