Gráfico1 - masterdock.mxmasterdock.mx/Pdfs/Marcos MMI.pdf · technical data sheet meskermesker issue date: november 2002 mesker 1864 ds-201-2 1/8” 11/32” 1/2” dia 9/32” hole

TECHNICAL DATA SHEET

MESKERMESKERMESKERIssue Date: November 2002

MESKER

1864

DS-201-1

STANDARD STEEL FRAMES

SPECIFICATIONS

MESKER STANDARD STEEL FRAMES

1. Frames shall be manufactured by Mesker Door Incorporated and designated as F-416 (16 GA) or F-414 (14 GA)

for 1 3/4” doors, F-412 for Bullet Resistant Frames and F-816 (16 GA) for 1 3/8” doors.

2. Frames shall be fabricated from cold rolled or A60 galvannealed steel.

3. Frames shall be furnished knocked down. Mitered corners shall have a strong four tab interlocking system to

maintain tight fineline miters.

4. Frames for 1 3/4” doors shall be prepared for a 4 1/2” x 4 1/2” standard or heavy weight template hinges and

ANSI 115.1 universal strike.

5. Frames for 1 3/8” doors shall be prepared for 3 1/2” x 3 1/2” standard weight template hinges and ANSI 115.3

cylindrical strike.

6. Frames are standard with 7 gauge hinge reinforcements.

7. Frames shall be adequately reinforced for all hardware.

8. Strike and hinge reinforcements shall be protected by plaster guards.

9. Frames shall be supplied with 1 sill anchor.

10. Frames shall be furnished with rubber mutes, three per strike jamb.

11. Frames shall receive 1 coat of baked-on rust inhibitive gray primer.

12. For installation instructions see ANSI A250.11-2001.



MESKER

1864

DS-201-2

1/8”

11/32”

1/2” DIA 9/32” HOLE IN FRAME

PHEUMATIC CHAMBER

MUTES

TO INSTALL IN FIELD INSERT BLUNT END OF 3/32” DIAMETER WIRE OR TOOL INTO THE HOLEIN CENTER OF THE MUTE. MOISTEN CONE PORTIONS AND INSERT INTO 9/32” HOLE IN STOPOF FRAME, PUSH SLOWLY WITH A CIRCULAR MOTION TO ELONGATE CONICAL PORTIONSUFFICIENTLY TO SET MUTE IN PLACE.

STANDARD FRAME PROFILES

6’-8”

7’-0”

7’-2”

8’-0”

2’-0”

2’-4”

2’-6”

2’-8”

3’-0”

3’-6”

3’-8”

4’-0”

4’-0”

4’-8”

5’-0”

5’-4”

6’-0”

7’-0”

7’-4”

8’-0”

3”

3 3/4”

4 3/4”

5 3/4”

7 3/4”

8 3/4”

2 3/16”

2 3/4”

3 3/4”

4 7/8”

6 3/4”

7 3/4”

FINISHEDOPENINGHEIGHT SINGLE DOUBLE

JAMBDEPTH

THROATOPENING

FINISHED OPENINGWIDTH

FRAME DIMENSIONS

JAMB DEPTH

4 3/4” 5 3/4”6 3/4” 7 3/4” 8 3/4”

1 9/16” VARIES 1 15/16”

1/2”3 3/4” 4 7/8”

5 3/4” 6 3/4” 7 3/4”1/2”

THROAT OPENING7/16” ON

5 3/4” DEPTH

2”

5/8” TYP

1 15/16”1 9/16”

3”

2”

13/32” 13/32”

3 3/4”

1 15/16”1 9/16”

2”

1/2” 1/2”

NETDOORWIDTH

2”

2”

2”

7 1/4”

EQUAL

NETDOOR

HEIGHT

EQUAL

12 1/4”

HINGECL

STRIKE CL

40 5/16”



MESKER

1864

DS-201-3

HINGE PREPARATIONWILL TAKE 3 1/2” X 3 1/2”TEMPLATE HINGES ORNON-TEMPLATE (S.D.I.) HINGES

#10 GUAGE HINGEREINFORCEMENTPROJECTION WELDEDTO FRAME

#20 GUAGE PLASTERGUARD PROJECTIONWELDED TO HINGEREINFORCEMENT

DRILLED AND TAPPEDFOR #10-24 SCREWS

23/64”

1 25/64”

3 1/2”

23/64”

1 25/64”

21/32”

5/32”

25/64”

21/64”

1/4” BACKSET

1 3/8”

STANDARD 3 1/2” HINGE MORTISEFOR 1 3/8” FRAMES

HINGE PREPARATIONWILL TAKE 4 1/2” HIGHTEMPLATE HINGESONLY STANDARD ORHEAVY WEIGHT, NON-TEMPLATE HINGESCANNOT BE USED

3/16” HINGEREINFORCEMENTPROJECTION WELDEDTO FRAME.

#20 GUAGE PLASTERGUARD PROJECTIONWELDED TO HINGEREINFORCEMENT

PROJECTIONS TODRILL OUT FORHEAVY WEIGHTHINGES 4 PLACES.


1/2”

1 1/8”

1 15/64”

1 1/8”4 1/2”

1/2”

5/32”

5/8”

3/8”

5/8”

5/16” BACKSET

1 5/8”


#20 GUAGE PLASTERGUARD PROJECTIONWELDED TO STRIKE

REINFORCEMENT

#14 GUAGE STRIKEREINFORCEMENTPROJECTION WELDEDTO FRAME


STRIKE MORTISECONFORMSTO ANSI A115.1

1 1/8”

5/8”

5/16” BACKSET

1 1/4”

5/8”

3/32”

3 3/8”

4 1/8”

4 7/8”

“U” STRIKE MORTISE

#20 GUAGE PLASTERGUARD PROJECTIONWELDED TO STRIKE

REINFORCEMENT

#14 GUAGE STRIKEREINFORCEMENTPROJECTION WELDEDTO FRAME

PIERCED AND TAPPEDFOR #8-32 SCREWS


9/16”

1/4” BACKSET

1 1/8”

1 1/2”

2 1/8”

2 3/4”

3/32”

9/16”

“C” STRIKE MORTISE



MESKER

1864

DS-201-4

GENERAL INFORMATION

STRIKE PREPARATIONS

HINGE PREPARATIONS

ANCHORS

SILL ANCHORS

MUTES

Frames are prepared for 4 7/8” high universalstrike (ANSI 115.1) specify “U” and 2 3/4” highcylindrical strike (ANSI 115.3) specify “C”.

Frames for 1 3/4” doors are prepared for 4 1/2”x 4 1/2” standard or heavy weight templatehinges. 1 1/2” pair on doors up to 7’-2” inheight and 2 pair on 7’-10” and 8’-0”.

Frames for 1 3/8” doors are prepared for 3 1/2”x 3 1/2” standard weight template hinges. 1pair on 6’-8” doors and 1 1/2” pair on 7’-0”and 7’2” doors. U/L labeled frames have 1 1/2”pair on all sizes.

Anchors must be specified to correspond withwall condition. Details are shown on thefollowing data sheets:

Wire Anchor - DS 246

Masonry Tee Anchor - DS 242

Wood and Steel Stud Anchor - DS 243

U/L Labeled Masonry Anchor - DS 241

Existing Wall Anchor - DS 245

Each jamb is supplied with 1-16 gauge sillanchor.

Each frame is furnished with rubber mutes.Three per strike jamb.

TABS

MUTES3 PER

STRIKE JAMB

HINGE STRIKE

SILL ANCHOR16 GAUGE

PLASTER GUARD

STRIKE REINFORCEMENT

1 9/16”OR 1 15/16”

PLASTER GUARD

1 9/16”OR 1 15/16”

HINGE

REINFORCEMENT

TAB IS OFFSET TOOBTAIN SMOOTH BENDALONG TOP OFFRAME HEAD.

SECTION THRU TAB



MESKER

1864

DS-201-5

F-SERIES ASSEMBLY INSTRUCTION

1. Slide header over jamb corner tabs, insert into slots.

2. Bend tabs on jamb rabbets out per illustration. (NOTE: Bending tabs in will increase door opening dimension.)

3. Bend corner tabs in per illustration.

TAB IS OFFSET TOOBTAIN SMOOTH BENDALONG TOP OF FRAMEHEAD

HEAD

TABS

JAMB

SECTION THRU TAB

(BEND IN)

CORNER TABS

JAMB TABS(BEND OUT)

VARIES



MESKER

1864

DS-202-1

DJ SERIESSTANDARD STEELDRYWALL FRAMES

SPECIFICATIONS

MESKER STANDARD STEEL DRYWALL FRAMES

1. Frames shall be manufactured by Mesker Door Incorporated and designated as FDJ416 (16 GA) for 1 3/4” doors,

and as FDJ816 (16GA) for 1 3/8” doors.

2. Frames shall be fabricated from cold rolled or A60 galvannealed steel as called for on plans.

3. Frames shall be knocked down construction. Frames shall be furnished with two (2) adjustable jamb lock

mechanisms. Two (2) dimpled holes at the base of each jamb to stabilize the frame at installation.

4. Frames for 1 3/4” doors shall be prepared for 4 1/2” x 4 1/2” standard or heavy weight template hinges and

ANSI 115.1 universal strike.

5. Frames for 1 3/8” doors shall be prepared for 3 1/2” x 3 1/2” standard weight template hinges and ANSI 115.3

cylindrical strike.

6. Frames shall be adequately reinforced for all hardware.

7. Frames shall be furnished with rubber mutes, three per strike jamb.

8. Frames shall receive 1 coat of baked-on rust inhibitive gray primer.

9. For installation instructions see DS-202-5.



MESKER

1864

DS-202-2

STANDARD FRAME PROFILES

JAMB DEPTH

4 1/2” - 7 1/4”1/8” INCREMENTS

1 9/16” VARIES 1 15/16” 5/8”

2”

1/2”

1/4”

THROATOPENING

1/2”

1 9/16”1 15/16”

1” VARIES 5/8”

2”

1/2”

1/4”

1/2”3 5/8” - 4 3/8”

1/8” INCREMENTS

DIMPLEDFOR A #10DRYWALL

SCREW

3/4”

3/4”

STANDARD OPTIONAL

“DFA”ANCHOR

FRAME HANDING

DOUBLE

RHR ACTIVE RH ACTIVE

LHR ACTIVELH ACTIVE

SINGLEINSIDE

OUTSIDE

RHR RH

INSIDE

OUTSIDE

LHR LH

2” 2”

2”

NETDOORWIDTH

7 1/4”

NETDOOR

HEIGHT

EQUAL

EQUAL

12 1/4”

HINGE

STRIKE

CL

CL

40 5/16”

FINISH FLOOR

INSIDE

OUTSIDE

INSIDE

OUTSIDE

6’-8”

7’-0”

7’-2”

2’-0”

2’-4”

2’-6”

2’-8”

3’-0”

3’-4”

3’-6”

3’-8”

4’-0”

4’-0”

4’-8”

5’-0”

5’-4”

6’-0”

6’-8”

7’-0”

FINISHEDOPENINGHEIGHT SINGLE DOUBLE

FINISHED OPENINGWIDTH

STANDARD SIZES

4 1/2”

5 5/8”

5 7/8”

3 1/2”

4 5/8”

4 7/8”

JAMBDEPTH

THROATOPENING

FRAME DIMENSIONS



MESKER

1864

DS-202-3


HINGE PREPARATIONWILL TAKE 4 1/2” HIGHTEMPLATE HINGESONLY. NON-TEMPLATEHINGES CANNOT BEUSED.

3/16 HINGEREINFORCEMENTPROJECTION WELDEDTO FRAME

PROJECTIONS TODRILL OUT FORHEAVY WEIGHTHINGES 4 PLACES.

1/2”

1 1/8”

1 15/64”

1 1/8”4 1/2”

1/2”5/8”

3/8”

5/8”

1 5/8”

5/16” BACKSET

5/32”

DRILLED & TAPPEDFOR #12-24 SCREWS


#10 GAUGE HINGEREINFORCEMENTPROJECTION WELDEDTO FRAME.

23/64”

1 25/64”

1 25/64”

23/64”

3 1/2”

21/32”

21/64”

25/64”

1 3/8”

1/4” BACKSET

5/32”

HINGE PREPARATIONWILL TAKE 3 1/2” X 3 1/2”TEMPLATE HINGES ORNON-TEMPLATE (S.D.I.)HINGES

DRILLED &TAPPEDFOR #10-24SCREWS

“U” STRIKE MORTISE

#14 GAUGE STRIKEREINFORCEMENTPROJECTION WELDEDTO FRAME

#20 GAUGE PLASTERGUARD PROJECTIONWELDED TO STRIKEREINFORCEMENT

1 1/8”

4 7/8”

4 1/8”

3 3/8”

3/32” 5/8”

5/8”

1 1/4”

5/16” BACKSET



“C” STRIKE MORTISE

#14 GAUGE STRIKEREINFORCEMENTPROJECTION WELDEDTO FRAME

#20 GAUGE PLASTERGUARD PROJECTIONWELDED TO STRIKEREINFORCEMENT

DRILLED & TAPPEDFOR #8-32 SCREWS

2 3/4”

2 1/8”

1 1/2”

9/16”9/16”

3/32”

1 1/8”

1/4” BACKSET

STRIKE MORTISECONFORMS TOANSI A115.3



MESKER

1864

DS-202-4

DETAIL “B”ADJUSTABLE JAMB LOCK

ADJUSTABLEJAMB LOCK(LOCATED ATTHE TOP OFEACH JAMB)

TABS

SEEDETAIL “B”

HINGE

MUTES3 PER

STRIKE JAMB

STRIKE

MUTES

TO INSTALL IN FIELD:INSERT BLUNT END OF 3/32”DIAMETER WIRE OR TOOL INTOTHE HOLE IN CENTEROF THE MUTE. MOISTENCONE PORTIONS AND INSERTINTO 9/32” HOLE IN STOP OFFRAME. PUSH SLOWLY WITHA CIRCULAR MOTION TOELONGATE CONICAL PORTIONSUFFICIENTLY TO SET MUTEIN PLACE.

GENERAL INFORMATION

STRIKE PREPARATION

HINGE PREPARATIONS

ANCHORS

MUTES

ROUGH OPENING DIMENSIONS

- Frames are prepared

for 4 7/8” high universal strike (ANSI 115.1)

specify “U” and 2 3/4” high cylindrical strike

(ANSI 115.3) specify “C”.

- Frames for 1 3/4”

doors are prepared for 4 1/2” x 4 1/2”

standard weight template hinges 1 1/2” pair on

doors up to 7’2” in height. 2 pair on 7’10” and

8’0”.

Frames for 1 3/8” doors are prepared for 3

1/2” x 3 1/2” standard weight template hinges.

1 pair on 6’8” doors and 1 1/2” pair on 7’0”

and 7’2” doors.

- The Mesker DJ Series Drywall

Frame is stabilized with two (2) adjustable jamb

locks, located near the top of each jamb. There

are two (2) sill anchors available. The stocked

frame has the faces dimpled for a #10 drywall

screw. The “DFA” anchor can be provided as an

extra cost option.

- Each frame is furnished with rubber

mutes. Three per strike jamb.

- Add to door

opening dimensions: 1 7/8” to width and 1

1/2” to height, i.e. for a 3068 door frame, the

rough opening is 37 7/8 x 81 1/2”.

SILL ANCHOR16 GUAGE



MESKER

1864

DS-202-5

SERIES FDJ416 DRYWALL FRAMEINSTALLATION

INSTALL STRIKE JAMB BY SLIDING OVERWALL AT TOP AND ENGAGING CORNERREINFORCING INTO HEADER. PIVOTJAMB INTO PLACE.

CHECK DOOR OPENING DIMENSION AT BASE OF FRAME(SAME DIMENSION AS BETWEEN JAMBS AT HEADER.) SECUREJAMBS WITH DRYWALL SCREW (NOT FURNISHED) THROUGHPUNCHED HOLE AT BASE OF FRAME. BE SURE TO ATTACHSCREWS ON EACH SIDE OF JAMBS (4 PLACES.)

INSTALL HEADER INTO POSITIONAPPROX. 1” FROM TOP AND IN THECENTER OF THE ROUGH OPENING.

ADD TO DOOR OPENING DIMENSIONS:1 7/8” TO WIDTH AND 1 1/2” TOHEIGHT. FOR A 3068 DOOR FRAME,THE ROUGH OPENING IS 37 7/8” X 811/2”.

REPEAT STEP #3 WITH HINGE JAMB. PULLHEADER DOWN TIGHTLY ONTO JAMBS. LOCKHEADER AND JAMB TOGETHER BY BENDINGOVER EXPOSED TABS.

TURN ADJUSTING SCREWS IN BOTH JAMBSCOUNTERCLOCKWISE UNTIL ANCHOR ISRESTING AGAINST THE WALL.

CHECK DOOR OPENING DIMENSION AT BASE OF FRAME (SAMEDIMENSION AS BETWEEN JAMBS AT HEADER.) SECURE JAMBSWITH DRYWALL SCREWS (NOT FURNISHED) THROUGH SILL

ANCHOR. (NOTE: SPECIFY ON YOUR ORDER IF THISMETHOD OF ATTACHMENT IS REQUIRED.)

IF FEASIBLE, HANG DOOR NOW ANDADJUST FRAME ON WALL TO ALLOWPROPER DOOR/FRAME CLEARANCES ORPLUMB FRAME WITH CARPENTER SQUAREAND/OR LEVEL. (ADJUST HEADERLEVELNESS BY SHIMMING UNDER JAMBS.)

ALT.

NOMINALDOOR WIDTH

+1 7/8”

ANCHOR ADJUSTINGSCREW (TYPICAL BOTH

JAMBS)

HEADER

STRIKEJAMB

HINGEJAMB

LEVEL

OR

SQUARE

DIMPLED FOR A#10 DRYWALL

SCREW

3/4”

3/4”

NOMINALDOOR HEIGHT

+ 1 1/2”

“DFA”ANCHOR

Documents

Gráfico1 - masterdock.mxmasterdock.mx/Pdfs/Marcos MMI.pdf · technical data sheet meskermesker issue date: november 2002 mesker 1864 ds-201-2 1/8” 11/32” 1/2” dia 9/32” hole