GS-Oolite wireless routing module Spec

GS-Oolite is a highly integrated wireless routing module. It is not only a wireless module, it

is a complete route, only energized, it can work in a wireless AP module, if coupled with a

network transformer and RJ45 network port, he is one of 3 wireless routing。

GS-Oolite power is very low, working alone, only 0.36W, very suitable for battery products,

it has a 150M wireless transmission rate, up to 20 gpios. can be defined as input and

output.

it's design for wifi hard disk, WiFi router, remote monitoring, remote video, Industrial

control DIY and so on

Characteristics:

CPU: AR9331 400Mhz MIPS core

RAM: 64M DDR2 RAM

Flash: 4/8/16M Flash

Wireless speed: 150Mbps

General GPIO: 20 (not including TX, RX)

USB: Usb 2 master interface, support USB hub extension

Power supply voltage: 3.3V.

Port: 3 100Mbps network interface

Antenna: the built-in PCB /ipx external antenna antenna.

Debug: serial debugging interface has been out.

Power: 0.36W

Product size: 28.2 * 52MM

compatible with tplink wr703n, wr743 official firmware

Pictures:

Pins :

Welding Note: please confirm the Net-pow pin not short circuit with GND by multr.

Best to weld this pin fisrt. to avoid overloading and damaging the cable network

function.

Pin No. Name GPIO state(default) spec

1 GND GROUND

2 ANT External antenna interface

3 GND GROUND

4 GND GROUND

5 GPIO27/SYS_LED output System indicator

6 GPIO11/RESET input Reset button, high level effective

7 GPIO7/TDO input I/O

8 GPIO6/TDI input I/O

9 JTAG_TCK

10 GPIO8/TMS output I/O

11 GPIO26 output I/O

12 GND GROUND

13 VCC3V3 3.3V

14 GPIO17 Network lamp P4 Network indicator lamp

15 GPIO16 output I/O

16 GPIO15 Network lamp P2 Network indicator lamp

17 GPIO14 output I/O

18 GND GROUND

19 GPIO13 Network lamp P0 Network indicator lamp

20 GPIO1 output I/O

21 GPIO0 output I/O

22 GND GROUND

23 GND GROUND

24 RXD RX

25 TXD TX

26 GND GROUND

27 GPIO23 output I/O

28 GPIO20 output I/O

29 GPIO19 output I/O

30 GPIO18 output I/O

31 GPIO22 output I/O

32 GPIO24 output I/O

33 GPIO21 output I/O

34 VCC3V3 3.3V

35 GND GROUND

36 P4_RX+

P4 Network Port 37 P4_RX-

38 P4_TX+

39 P4_TX-

40 GND GROUND

41 P2_RX+

P2 Network Port 42 P2_RX-

43 P2_TX-

44 P2_TX-

45 GND GROUND

46 P0_RX+

P0 Network Port 47 P0_RX-

48 P0_TX+

49 P0_TX-

50 VCC3V3 3.3V

51 VCC3V3 3.3V

52 USB- USB Master USB-

53 USB+ USB Master USB+

54 GND GROUND

55 NET_POW Bias power output

56 GND GROUND

57 GND GROUND

Remarks.

1 All power pins (VCC3V3) is a module power supply input pin, theoretically, in a pin on

the input 3.3V voltage can be, recommend the use of 50 foot and the 51 foot together for

module power supply.GND also.

2 all unused GPIO can empty, no need pull up or pull down.

3 NET_POW, network transformer biasing power output ,The output of 2.2V, to offset

the use of wired network transformer

4 network: the default P4 is wan, P0, P2 for lan.

5 GPIO output voltage: 2.62V(depends on AR9331)

Pins Size：

Recommended Pcb Pads: