GSA AO2 - AISP 3 F 2 W ww.ais-inc.com Revision Dec 2018 ... AO2 Statement of Line 5 AO2 Finish Options 7 PANELS AO2 Panels Product Details 9 Non-Powered Hard Surface Panels 12 Powered

December 2018 Price List

GSA AO2

This page intentionally left blank.

3Electronic Libraries available at 2020.net and ProjectMatrix.com

Phone: 800.434.7400 Fax: 978.562.0811 Web: www.ais-inc.comRevision Dec 2018© 2018, AIS, Inc.

TABLE OF CONTENTS

PRODUCT INFORMATIONAO2 Statement of Line 5AO2 Finish Options 7

PANELSAO2 Panels Product Details 9Non-Powered Hard Surface Panels 12Powered Hard Surface Panels 14Non-Powered Hard Surface Acoustical Panels 16Powered Hard Surface Acoustical Panels 17Non-Powered Quarter Glass Panels 18Powered Quarter Glass Panels 19Non-Powered Half Glass Panels 20Powered Half Glass Panels 21Non-Powered Air Flow / Wall Access Panels 22Powered Air Flow / Wall Access Panels 24ADA Door Panels 26Sliding Doors 27

CONNECTORSStraight Rod Connectors 282-Way Connectors, 3-Way Connectors, 4-Way Connectors and End Caps 29Wall Mount Kits, HiLo Finishing Trips and Wall Tracks 30

ELECTRICALAO2 Electrical Product Details 31Jumpers 33Duplex Outlets 34In-Feeds 35Retrofit Kits, Power/Data Pole Kits, Junction Boxes, Data Plate Kits 36

SUPPORTCantilevers and Side Support/Rear Brackets 37End Panels and Brackets 38Panel Mounted A-Legs 39

STORAGEMid-Height Shelf Units 40Mid-Height Corner Shelf Units 41Type C Flipper Door Units 42Type C Raised Flipper Door Units 43Type D Flipper and Raised Flipper Door Units 44Sliding Door Units 45Raised Sliding Door Units 46Cabinet Door Units 47Raised Cabinet Door Units 48

ACCSESSORIESTackboards, Tool Rail Kits and Panel Coat Hooks 49Whiteboards 50

WARRANTY & TERMS AND CONDITIONSFor Warranty & Terms and Conditions please visit:https://aiscmsprod blob core windows net/infocenter/AISTermsWarranty pdf

GSA AO2

This page intentionally left blank



STATEMENT OF LINEPanels, Connectors and Electrical

AO2PANELS

CONNECTORS

Hard Surface PanelsPowered or Non-Powered

Hard Surface Acoustical PanelsPowered or Non-Powered

Quarter Glass PanelsPowered or Non-Powered

Half Glass PanelsPowered or Non-Powered

Air Flow / Wall Access PanelsPowered or Non-Powered

Sliding Door Handle Kits

Straight Rod Connectors

Wall Mount Kits

Panel-to-Panel Jumpers Transitional Jumpers Lateral Pass Through Jumpers

USB OutletsDuplex Outlets

HiLo Finishing StripsUnequal Height Straight Rod

Connector Kits

2-Way Connectors

Wall Tracks3-Way Connectors

Non-Locking Sliding DoorsADA Door PanelsWith or Without Glass, Left or Right HandWithout Glass Right Hand Door Shown

4-Way Connectors

ELECTRICAL

Duplex Outlet Hole Covers

Side Mounted Base In-Feeds

Receptacle Mounted Base In-Feed

Ceiling In-Feeds Electrical Retrofit Kits Data Plate Kits Hardwire Junction Box Double Channel Power / Data Pole Kit

GSA AO2


Phone: 800.434.7400 Fax: 978.562.0811 Web: www.ais-inc.comRevision Dec 2018

© 2018, AIS, Inc.

STATEMENT OF LINESupport, Storage and Accessories

SUPPORT

STORAGE

ACCESSORIES

Standard Cantilevers

Clear Access End Panels

Shared Cantilevers Side Support / Rear Brackets Panel Mounted Shelf Cantilevers Standard End Panels

Pedestal-to-Pedestal Attachment Bracket

Countertop Brackets Panel Mounted A-Legs

Mid-Height Shelf Units Linear Mid-Height Shelf Units Mid-Height Corner Shelf Unit Linear Mid-Height Corner Shelf Unit

Type C Flipper Door UnitMetal/Fabric or Laminate FrontMetal/Fabric Door Front Shown

Type C Raised Flipper Door UnitMetal/Fabric or Laminate FrontMetal/Fabric Door Front Shown

Type D Flipper Door Unit Type D Raised Flipper Door Unit

Sliding Door UnitMetal/Fabric or Laminate FrontMetal/Fabric Door Front Shown

Raised Sliding Door UnitMetal/Fabric or Laminate FrontMetal/Fabric Door Front Shown

Cabinet Door UnitMetal/Fabric or Laminate FrontMetal/Fabric Door Front Shown

Raised Cabinet Door UnitMetal/Fabric or Laminate FrontMetal/Fabric Door Front Shown

Tackboards Tool Rail Kits Tool Rail Kits White Board w/ Marker TrayFramed or Frameless

Framed White Board Shown

GSA AO2



FINISH OPTIONSFabric Options

• It is mandatory that you work directly with your AIS Customer Service Representative for all COM related testing and orders. They will provide all necessary forms to you, as well as work with you with regard to sending in correct yardage and where to send it, along with necessary RA# or #s. Please note an RA must be submitted along with the fabric for testing, as well as an RA created for an actual order.

• Please Note: A three to five yard sample is required for testing and approval for use on all monolithic panel systems. A one yard sample is required for testing and approval on Divi Insert Tiles, Matrix Tiles, flipper doors and tackboards. We may be able to test upholstery fabrics with a swatch, your Customer Service Representative will advise based on the fabric being tested; otherwise a 1 yard sample must be submitted for testing. Results take 48 - 72 hours.

• Customer Service must be advised as to the width of the fabric rolls being supplied (54”W or 60”W). Customer Service must also be advised if the fabric has a backer. • Yardage required for the job must be calculated by an AIS Customer Service Rep.• Once AIS has approved the COM fabric, a fabric sample needs to be marked by the dealer with “Front”, “Top”, and “Bottom”, to be sure fabric is applied correctly. The fabric

sample then needs to be attached to a COM Fabric Dealer Form and forwarded to AIS Customer Service. The COM Fabric Dealer Form may be downloaded or printed here.• Fabrics may be discontinued or obsolete without notice.• Contact AIS Customer Service with any questions regarding fabric availability. • All directional fabric will be railroaded.

PANEL FABRICS BY GUILFORD OF MAINEName Style Number GradeAnchorage 2335 BBailey 2299 BDrift 2539 BLido 2858 BMingle 2527 BSpinel 3582 BSprite 2671 BStreetwise 2721 BReeds 3078 BTweed 2737 BBirdseye 2748 CBix 3008 CBroadcast 2758 CCoastline 3495 CCrosstown 2526 CFr701 2100 CAuster 2537 DBlock Party 2538 DGroove 3497 DLily Pad 2318 DNetwork 4158 DNitro 2317 DPhone Tag 2314 DRegatta 2400 DTempest 2120 DCosmos 2655 E

PANEL FABRICS BY AISName Style Number GradeAvenue Dusk 2062 AAvenue Park Place 2064 ACape Cod Chatham 2711 ACape Cod Falmouth 2712 ACape Cod Harwich 2713 ACape Cod Hyannis 2714 ACape Cod Martha’s Vineyard 2715 ACape Cod Nantucket 2716 ACape Cod Provincetown 2717 AEngage Denim 2066 AEngage Neutral 2065 AEngage Rain Cloud 2067 AEngage Toffee 2068 ANew England Boston 2700 ANew England Cambridge 2701 ANew England Concord 2702 ANew England Dixville Notch 2703 ANew England Hartford 2704 ANew England Lexington 2705 ANew England Newton 2706 ANew England Providence 2707 ANew England Rockport 2708 ANew England Salem 2709 ANew England York 2710 ARainfall Bliss 2059 ARainfall Shore 2060 ARainfall Sundown 2057 ARainfall Twilight 2058 ASimplicity Blue Smooth 2001 ASimplicity Chamoise 2002 ASimplicity Grey Blue 2004 ASimplicity Sandy Pebble 2005 ASimplicity Stone 2530 ASimplicity Twizzle Tan 2008 AStream Light Sand 2501 A

C.O.M. Fabric Policy

GSA AO2

http://cms.ais-inc.com/infocenter/Warranty_other/COMFabric.pdf



© 2018, AIS, Inc.

FINISH OPTIONSPaint, Edgeband, Laminate and Tempered Glass Options

AO2 PAINT OPTIONSName Color Code AO2 Panel Grade AO2 Base GradeBlack BK A -Chalk CK - -Dark Tone DT A AGrey Value 1 GV1 A -Innertone HT A -Light Tone LT A -Medium Tone MT A ASatin White SW - -Warm Brown WB A -Champagne Metallic CHM - -Dark Grey Metallic DGM - -Flint Grey Metallic FGM - -Light Grey LG - -Metallic Silver MS - -Tan Value 1 TV1 B -Warm White WW - -Woodrose WR - -Antique Gold AG - -Blue BL - -Graphite Sky GS - -Lite Silver Smooth LSS - -Orange OG - -Red RD - -Violet VT - -Yellow YW - -

• Minimum order size for any custom color is $75,000 list. Extended lead-time will apply.• Any color not shown on Quick Ship, Standard Grade A, B or C will be considered custom.• A $450 net paint match fee will be assessed following receipt of (2) 5”x5” samples of

paint being matched. • Minimum order size for any custom color is $75,000.00 list. Extended lead-time will apply.• Additionally, Grade C paint up-charges will be applied to all applicable products on

the order.• Important Custom Paint Note: Most paint match pricing can be covered by the Grade

C up-charge in the catalog, however the final pricing can only be determined after the paint is matched and a product list is provided to AIS customer service. An additional fee may apply based on job size and paint color.

Custom Paints Custom Edgeband Options

EDGEBAND OPTIONSName Color Code GradeAbsolute Acajou AA AAimtoo Savatre AS ABlack BK ABrazilwood BZ ACabinet Almond CA AChalk CK ACorporate Walnut CT ADark Rum Cherry DR ADark Tone DT AGrand Cherry GC AGrey Value 1 GV1 AInnertone HT ALeave Likatre LV ALight Tone LT ALooks Likatre LK AMedium Tone MT AMidwest Maple MM ANightfall NF ARecon Oak RC ASatin White / True White SW / TW AStorm ST ASummer Drops SD ATrytoo Savatre TS AWarm Brown #1 WB1 AWoodrose WR A

• A $450 net edge match fee will be assessed to custom match non-standard edgeband. • Minimum order size for any custom color is $75,000.00 list. Extended lead-time will apply.

AO2 LAMINATE OPTIONSName GradeAbsolute Acajou BAimtoo Savatre BBlack BBrazilwood BCabinet Almond BChalk BCorporate Walnut BDark Rum Cherry BGrand Cherry BLeave Likatre BLooks Likatre BMidwest Maple BNightfall BParis White Potterware BRecon Oak BStorm BSummer Drops BTitanium EV BTrue White BTrytoo Savatre B

TEMPERED GLASS OPTIONS

NamePanels/Frame/Tiles/

Screens1/4” Thick

Frameless Glass3/8” Thick

Frameless GlassClear Y Y YFrosted Y Y YAqui N N YBlue N N YBronze Tint Y Y NGrey Tint Y Y NPebble Y N NSpraylight Y N N

All glass is tempered. The etched side of Frosted is always on Side A of the Frame or Panel. Side B of this glass options are smooth. Please see specific price list pages on each type of glass for list pricing and up-charges.

GSA AO2



Fabric Covered, Hard Surface, Powered/Non-Powered

Quarter Glass, Fabric Covered, Hard Surface, Powered/Non-Powered

ADA Door Panel

Half Glass, Fabric Covered, Hard Surface, Powered/Non-Powered

Fabric Covered, Hard Surface Acoustic Panels, Powered/Non-Powered

Heights: Nominal Heights: 39”, 47”, 53”, 67” ,85”Actual Minimum Heights: 38 1/2”, 46 1/2”, 52 1/2”, 66 1/2”, 84 1/2” - Leveling Glide Range is 1 1/2”

Heights: Nominal Heights: 67”, 85”Actual Minimum Heights: 66 1/2”, 84 1/2” - Leveling Glide Range is 1 1/2”

Heights: Nominal Heights: 85”Actual Minimum Heights: 84 1/2” - Leveling Glide Range is 1 1/2”

Heights: Nominal Heights: 53”, 67”, 85”Actual Minimum Heights: 52 1/2”, 66 1/2”, 84 1/2” - Leveling Glide Range is 1 1/2”

Heights: Nominal Heights: 53”, 67”, 85”Actual Minimum Heights: 52 1/2”, 66 1/2”, 84 1/2” - Leveling Glide Range is 1 1/2”

Widths: Actual/Nominal Widths: 12”*, 24”, 30”, 36”, 42”, 48”, 60” (Not available in 85”H) *Non-Powered Only

Widths: Actual/Nominal Widths: 24”, 30”, 36”, 42”, 48”

Widths: Actual/Nominal Widths: 48”

Widths: Actual/Nominal Widths: 24”, 30”, 36”, 42”, 48”

Widths: Actual/Nominal Widths: 12”*, 24”, 30”, 36”, 42”, 48”, 60” (Not available in 85”H)*Non-Powered Only

PANELSAO2 Panels Product Details

Product Detail 1Panel Statement of Line

39”H47”H

53”H

67”H

85”H

53”H

67”H

85”H

67”H

85”H

52 7/16”H

70 7/16”H

53”H

67”H

85”H

39 1/2”H

85”H

OpeningWidth

35 5/16”

GSA AO2



© 2018, AIS, Inc.

Product Detail 2Rules for Panel Stability without Components

The guidelines outlined below should be followed when designing AIS AO2 panels without components to ensure panel stability and safety. Change in height will not effect panel stability. Any panel not directly attached to a perpendicular panel or fixed wall will yield when pressure is applied.

4' Min

12' Max

2' Min

5'

4' Min

8' Max

4' Min

8'6' M

in

10'

2' Min

10'8' Max

8' Min

8' Min

20' Max

6' Min

16'

6' Min

4' Min

4' Min

15'

6' Min

10' Max

4' Min

2' Min

12' Max

Product Detail 3Rules for Panel Stability with Components

*

5' Max4' Max

4' Min

20' Max

4' Min

15' Max

3' Min

10' Max

2' Min

2' Min

8 '

2' Min

5' Max

4' Min

10' Max

4' Min

8' Max

3' Min

5' Max

4' Min

4' Max

3' Min

4' Max

**

*

* 30” worksurfaces must be supported at the front with side support brackets or floor support elements/pedestals.

The guidelines outlined below should be followed when designing AIS AO2 panels with components to ensure panel stability and safety. Change in height will not effect panel stability. Any panel not directly attached to a perpendicular panel or fixed wall will yield when pressure is applied.


GSA AO2



Product Detail 4Panel Creep Dimensions


(24" x 3) = 72"

0"

24" 24" 24"

0" 0"

3 1/2" 3 1/2"

(24" x 3) + 3 1/2" = 75 1/2"

(24" X 3) + (3 1/2" X 3) = 82 1/2 "

24" 24" 24"

3 1/2"

3 1/2"

3 1/2"3 1/2" 3 1/2"

(24" x 3) + 3 1/2" = 75 1/2"

(24" X 3) + (3 1/2" X 3) = 82 1/2 "

24" 24" 24"

3 1/2"

0"

3 1/2"

3 1/2"3 1/2"

3 1/2" 3 1/2"

(24" X 3) = 72"

(24" X 3) + (3 1/2" X 2) = 79"

24" 24" 24"

0" 0"3 1/2"

3 1/2"

Small increments are added to or taken away from the length of a run of panels as a result of the many ways panels are connected to each other. The accumulation of these increments is called Panel Creep. While AIS AO2 panels are “actual” size, the addition of 2-way, 3-way, 4-way, end, and wall mount connectors add increased dimensions.

Straight Connections:Add 0” to panel run for each straight connection. 24”W (nominal) panels are shown.

3-Way Connections:Add 3 1/2” each time a perpendicular panel is inserted into a panel run.

Finished End Connections:Add 1” to the end of a panel run for each finished end cap.

Wall Mount Connections:Add 1/2” to the end of a panel run for a wall mount connection.

4-Way Connections:Add 3 1/2” each time a perpendicular panel is inserted into a panel run.

2-Way Connections:Add 3 1/2” each time a perpendicular panel is added to the end of a panel run.

(24" x 3) + 1" = 73"

0"

24" 24"

0" 1"

24"

(24" x 3) + 1/2" = 72 1/2"

0"1/2"

24" 24"

0" 1/2"

24"

GSA AO2



© 2018, AIS, Inc.

Specify Notes

• Fabric Selection for Side A and B• Paint Selection for Panel Trim• Color Selection for Base Covers• Data Knockout Option

Non-Powered Panels - Hard Surface are fabric covered hard surface panels with a raceway unit.

PANELSNon-Powered Hard Surface Panels

NON-POWERED HARD SURFACE PANELSH W Model Number List Grade C Paint Data KO C.O.M Fabric Grade C Fabric Grade D Fabric39 12 P-HEFR3912 464 +10 +15 -37 +70 +13639 24 P-HEFR3924 500 +10 +15 -37 +70 +13639 30 P-HEFR3930 545 +10 +15 -37 +70 +13639 36 P-HEFR3936 615 +10 +15 -37 +70 +13639 42 P-HEFR3942 650 +10 +15 -37 +70 +13639 48 P-HEFR3948 680 +10 +15 -37 +70 +13639 60 P-HEFR3960 844 +10 +15 -37 +70 +136

47 12 P-HEFR4712 495 +10 +15 -47 +80 +16047 24 P-HEFR4724 529 +10 +15 -47 +80 +16047 30 P-HEFR4730 590 +10 +15 -47 +80 +16047 36 P-HEFR4736 673 +10 +15 -47 +80 +16047 42 P-HEFR4742 748 +10 +15 -47 +80 +16047 48 P-HEFR4748 768 +10 +15 -47 +80 +16047 60 P-HEFR4760 945 +10 +15 -47 +80 +160

53 12 P-HEFR5312 505 +10 +15 -57 +86 +16653 24 P-HEFR5324 541 +10 +15 -57 +86 +16653 30 P-HEFR5330 614 +10 +15 -57 +86 +16653 36 P-HEFR5336 717 +10 +15 -57 +86 +16653 42 P-HEFR5342 774 +10 +15 -57 +86 +16653 48 P-HEFR5348 825 +10 +15 -57 +86 +16653 60 P-HEFR5360 1,015 +10 +15 -57 +86 +166

GSA AO2



Specify Notes


Non-Powered Panels - Hard Surface are fabric covered hard surface panels with a raceway unit.

PANELSNon-Powered Hard Surface Panels

NON-POWERED HARD SURFACE PANELSH W Model Number List Grade C Paint Data KO C.O.M Fabric Grade C Fabric Grade D Fabric67 12 P-HEFR6712 538 +10 +15 -57 +100 +19067 24 P-HEFR6724 631 +10 +15 -57 +100 +19067 30 P-HEFR6730 706 +10 +15 -57 +100 +19067 36 P-HEFR6736 814 +10 +15 -57 +100 +19067 42 P-HEFR6742 869 +10 +15 -57 +100 +19067 48 P-HEFR6748 926 +10 +15 -57 +100 +19067 60 P-HEFR6760 1,140 +10 +15 -57 +100 +190

85 12 P-HEFR8512 616 +10 +15 -94 +120 +22685 24 P-HEFR8524 745 +10 +15 -94 +120 +22685 30 P-HEFR8530 827 +10 +15 -94 +120 +22685 36 P-HEFR8536 952 +10 +15 -94 +120 +22685 42 P-HEFR8542 1,014 +10 +15 -94 +120 +22685 48 P-HEFR8548 1,076 +10 +15 -94 +120 +226

GSA AO2



© 2018, AIS, Inc.

POWERED HARD SURFACE PANELSH W Model Number List Grade C Paint C.O.M Fabric Grade C Fabric Grade D Fabric39 24 P-HEFP3924 743 +10 -37 +70 +136

39 30 P-HEFP3930 787 +10 -37 +70 +136

39 36 P-HEFP3936 853 +10 -37 +70 +136

39 42 P-HEFP3942 889 +10 -37 +70 +136

39 48 P-HEFP3948 921 +10 -37 +70 +136

39 60 P-HEFP3960 1,077 +10 -37 +70 +136

47 24 P-HEFP4724 770 +10 -47 +80 +160

47 30 P-HEFP4730 832 +10 -47 +80 +160

47 36 P-HEFP4736 911 +10 -47 +80 +160

47 42 P-HEFP4742 984 +10 -47 +80 +160

47 48 P-HEFP4748 1,005 +10 -47 +80 +160

47 60 P-HEFP4760 1,181 +10 -47 +80 +160

53 24 P-HEFP5324 782 +10 -57 +86 +166

53 30 P-HEFP5330 851 +10 -57 +86 +166

53 36 P-HEFP5336 954 +10 -57 +86 +166

53 42 P-HEFP5342 1,008 +10 -57 +86 +166

53 48 P-HEFP5348 1,058 +10 -57 +86 +166

53 60 P-HEFP5360 1,243 +10 -57 +86 +166

Specify Notes

• Fabric Selection for Side A and B• Paint Selection for Panel Trim• Color Selection for Base Covers

Powered Panels - Hard Surface are fabric covered hard surface panels with a powered raceway unit. Duplex outlets and elec-trical jumpers are ordered separately. See “Electrical”. Two duplex outlet hole covers are included with each powered panel.

PANELSPowered Hard Surface Panels

GSA AO2



POWERED HARD SURFACE PANELSH W Model Number List Grade C Paint C.O.M Fabric Grade C Fabric Grade D Fabric67 24 P-HEFP6724 869 +10 -57 +100 +190

67 30 P-HEFP6730 941 +10 -57 +100 +190

67 36 P-HEFP6736 1,051 +10 -57 +100 +190

67 42 P-HEFP6742 1,103 +10 -57 +100 +190

67 48 P-HEFP6748 1,159 +10 -57 +100 +190

67 60 P-HEFP6760 1,370 +10 -57 +100 +190

85 24 P-HEFP8524 981 +10 -94 +120 +226

85 30 P-HEFP8530 1,058 +10 -94 +120 +226

85 36 P-HEFP8536 1,185 +10 -94 +120 +226

85 42 P-HEFP8542 1,243 +10 -94 +120 +226

85 48 P-HEFP8548 1,308 +10 -94 +120 +226

Specify Notes


Powered Panels - Hard Surface are fabric covered hard surface panels with a powered raceway unit. Duplex outlets and elec-trical jumpers are ordered separately. See “Electrical”. Two duplex outlet hole covers are included with each powered panel.

PANELSPowered Hard Surface Panels

GSA AO2



© 2018, AIS, Inc.

NON-POWERED HARD SURFACE ACOUSTICAL PANELSH W Model Number List Grade C Paint Data KO C.O.M Fabric Grade C Fabric Grade D Fabric53 12 P-HEAR5312 646 +10 +15 -57 +86 +166

53 24 P-HEAR5324 728 +10 +15 -57 +86 +166

53 30 P-HEAR5330 792 +10 +15 -57 +86 +166

53 36 P-HEAR5336 881 +10 +15 -57 +86 +166

53 42 P-HEAR5342 927 +10 +15 -57 +86 +166

53 48 P-HEAR5348 978 +10 +15 -57 +86 +166

53 60 P-HEAR5360 1,195 +10 +15 -57 +86 +166

67 12 P-HEAR6712 691 +10 +15 -57 +100 +190

67 24 P-HEAR6724 760 +10 +15 -57 +100 +190

67 30 P-HEAR6730 825 +10 +15 -57 +100 +190

67 36 P-HEAR6736 922 +10 +15 -57 +100 +190

67 42 P-HEAR6742 961 +10 +15 -57 +100 +190

67 48 P-HEAR6748 1,018 +10 +15 -57 +100 +190

67 60 P-HEAR6760 1,224 +10 +15 -57 +100 +190

85 12 P-HEAR8512 793 +10 +15 -94 +120 +226

85 24 P-HEAR8524 876 +10 +15 -94 +120 +226

85 30 P-HEAR8530 944 +10 +15 -94 +120 +226

85 36 P-HEAR8536 1,070 +10 +15 -94 +120 +226

85 42 P-HEAR8542 1,123 +10 +15 -94 +120 +226

85 48 P-HEAR8548 1,200 +10 +15 -94 +120 +226

Specify Notes

• Fabric Selection for Side A and B• Paint Selection for Panel Trim• Color Selection for Base Covers• Data Knockout Options

Non-Powered Panels - Hard Surface Acoustical Panels are fabric covered hard surface panels with acoustical panels and a raceway unit. Certain fabrics may not be used on hard surface acoustical panels.

PANELSNon-Powered Hard Surface Acoustical Panels

GSA AO2



POWERED HARD SURFACE ACOUSTICAL PANELSH W Model Number List Grade C Paint C.O.M Fabric Grade C Fabric Grade D Fabric53 24 P-HEAP5324 967 +10 -57 +86 +166

53 30 P-HEAP5330 1,026 +10 -57 +86 +166

53 36 P-HEAP5336 1,116 +10 -57 +86 +166

53 42 P-HEAP5342 1,161 +10 -57 +86 +166

53 48 P-HEAP5348 1,208 +10 -57 +86 +166

53 60 P-HEAP5360 1,424 +10 -57 +86 +166

67 24 P-HEAP6724 996 +10 -57 +100 +190

67 30 P-HEAP6730 1,057 +10 -57 +100 +190

67 36 P-HEAP6736 1,152 +10 -57 +100 +190

67 42 P-HEAP6742 1,195 +10 -57 +100 +190

67 48 P-HEAP6748 1,248 +10 -57 +100 +190

67 60 P-HEAP6760 1,451 +10 -57 +100 +190

85 24 P-HEAP8524 1,111 +10 -94 +120 +226

85 30 P-HEAP8530 1,179 +10 -94 +120 +226

85 36 P-HEAP8536 1,300 +10 -94 +120 +226

85 42 P-HEAP8542 1,355 +10 -94 +120 +226

85 48 P-HEAP8548 1,427 +10 -94 +120 +226

Specify Notes


Powered Panels - Hard Surface Acoustical Panels are fabric covered hard surface panels with acoustical panels and a pow-ered raceway unit. Duplex outlets and electrical jumpers are ordered separately. See “Electrical”. Two duplex outlet hole covers are included with each powered panel. Certain fabrics may not be used on hard surface acoustical panels.

PANELSPowered Hard Surface Acoustical Panels

GSA AO2



© 2018, AIS, Inc.

Specify Notes

• Fabric Selection for Side A and B• Paint Selection for Panel Trim• Color Selection for Base Covers• Data Knockout Options• Style Selection for Tempered Glass Insert

Quarter Glass Panels - Non-Powered have an aluminum wrapped tempered glass insert at the top of the panel that is available in multiple style finishes. The lower section of the panel is a fabric covered hard surface with a non-powered raceway unit. 45.167” Fabric Height on 67”H Panels. 59.167” Fabric Height on 85”H Panels.

NON-POWERED QUARTER GLASS PANELSH W Model Number List Grade C Paint Data KO C.O.M Fabric Grade C Fabric Grade D Fabric67 24 P-HEQGRW6724 1,365 +10 +15 -37 +70 +136

67 30 P-HEQGRW6730 1,510 +10 +15 -37 +70 +136

67 36 P-HEQGRW6736 1,652 +10 +15 -37 +70 +136

67 42 P-HEQGRW6742 1,796 +10 +15 -37 +70 +136

67 48 P-HEQGRW6748 1,939 +10 +15 -37 +70 +136

85 24 P-HEQGRW8524 1,551 +10 +15 -37 +70 +136

85 30 P-HEQGRW8530 1,723 +10 +15 -37 +70 +136

85 36 P-HEQGRW8536 1,895 +10 +15 -37 +70 +136

85 42 P-HEQGRW8542 2,065 +10 +15 -37 +70 +136

85 48 P-HEQGRW8548 2,327 +10 +15 -37 +70 +136

PANELSNon-Powered Quarter Glass Panels

GSA AO2



POWERED QUARTER GLASS PANELSH W Model Number List Grade C Paint C.O.M Fabric Grade C Fabric Grade D Fabric67 24 P-HEQGPW6724 1,580 +10 -37 +70 +136

67 30 P-HEQGPW6730 1,727 +10 -37 +70 +136

67 36 P-HEQGPW6736 1,875 +10 -37 +70 +136

67 42 P-HEQGPW6742 2,024 +10 -37 +70 +136

67 48 P-HEQGPW6748 2,168 +10 -37 +70 +136

85 24 P-HEQGPW8524 1,771 +10 -37 +70 +136

85 30 P-HEQGPW8530 1,947 +10 -37 +70 +136

85 36 P-HEQGPW8536 2,123 +10 -37 +70 +136

85 42 P-HEQGPW8542 2,297 +10 -37 +70 +136

85 48 P-HEQGPW8548 2,476 +10 -37 +70 +136

Specify Notes

• Fabric Selection for Side A and B• Paint Selection for Panel Trim• Color Selection for Base Covers• Style Selection for Tempered Glass Insert

Quarter Glass Panels - Powered have an aluminum wrapped tempered glass insert at the top of the panel that is available in multiple style finishes. The lower section of the panel is a fabric covered hard surface with a powered raceway unit. Duplex outlets and electrical jumpers are ordered separately. See “Electrical”. Two duplex outlet hole covers are included with each powered panel. 45.167” Fabric Height on 67”H Panels. 59.167” Fabric Height on 85”H Panels.

PANELSPowered Quarter Glass Panels

GSA AO2



© 2018, AIS, Inc.

Specify Notes

• Fabric Selection for Side A and B• Paint Selection for Panel Trim• Color Selection for Base Covers• Data Knockout Options• Style Selection for Tempered Glass Insert

Half Glass Panels - Non-Powered have an aluminum wrapped tempered glass insert at the top of the panel that is available in multiple style finishes. The lower section of the panel is a fabric covered hard surface with a non-powered raceway unit. Fabric height is 34.357” on all panels.

NON-POWERED HALF GLASS PANELSH W Model Number List Grade C Paint Data KO C.O.M Fabric Grade C Fabric Grade D Fabric53 24 P-HEHGRW5324 1,178 +10 +15 -37 +70 +136

53 30 P-HEHGRW5330 1,293 +10 +15 -37 +70 +136

53 36 P-HEHGRW5336 1,410 +10 +15 -37 +70 +136

53 42 P-HEHGRW5342 1,526 +10 +15 -37 +70 +136

53 48 P-HEHGRW5348 1,641 +10 +15 -37 +70 +136

67 24 P-HEHGRW6724 1,365 +10 +15 -37 +70 +136

67 30 P-HEHGRW6730 1,510 +10 +15 -37 +70 +136

67 36 P-HEHGRW6736 1,652 +10 +15 -37 +70 +136

67 42 P-HEHGRW6742 1,796 +10 +15 -37 +70 +136

67 48 P-HEHGRW6748 1,939 +10 +15 -37 +70 +136

85 24 P-HEHGRW8524 1,551 +10 +15 -37 +70 +136

85 30 P-HEHGRW8530 1,723 +10 +15 -37 +70 +136

85 36 P-HEHGRW8536 1,895 +10 +15 -37 +70 +136

85 42 P-HEHGRW8542 2,065 +10 +15 -37 +70 +136

85 48 P-HEHGRW8548 2,238 +10 +15 -37 +70 +136

PANELSNon-Powered Half Glass Panels

GSA AO2



POWERED HALF GLASS PANELSH W Model Number List Grade C Paint C.O.M Fabric Grade C Fabric Grade D Fabric53 24 P-HEHGPW5324 1,388 +10 -37 +70 +136

53 30 P-HEHGPW5330 1,510 +10 -37 +70 +136

53 36 P-HEHGPW5336 1,625 +10 -37 +70 +136

53 42 P-HEHGPW5342 1,747 +10 -37 +70 +136

53 48 P-HEHGPW5348 1,862 +10 -37 +70 +136

67 24 P-HEHGPW6724 1,580 +10 -37 +70 +136

67 30 P-HEHGPW6730 1,727 +10 -37 +70 +136

67 36 P-HEHGPW6736 1,875 +10 -37 +70 +136

67 42 P-HEHGPW6742 2,024 +10 -37 +70 +136

67 48 P-HEHGPW6748 2,168 +10 -37 +70 +136

85 24 P-HEHGPW8524 1,771 +10 -37 +70 +136

85 30 P-HEHGPW8530 1,947 +10 -37 +70 +136

85 36 P-HEHGPW8536 2,123 +10 -37 +70 +136

85 42 P-HEHGPW8542 2,297 +10 -37 +70 +136

85 48 P-HEHGPW8548 2,476 +10 -37 +70 +136

Specify Notes

• Fabric Selection for Side A and B• Paint Selection for Panel Trim• Color Selection for Base Covers• Style Selection for Tempered Glass Insert

Half Glass Panels - Powered have an aluminum wrapped tempered glass insert at the top of the panel that is available in multiple style finishes. The lower section of the panel is a fabric covered hard surface with a powered raceway unit. Duplex outlets and electrical jumpers are ordered separately. See “Electrical”. Two duplex outlet hole covers are included with each powered panel. Fabric height is 34.357” on all panels.

PANELSPowered Half Glass Panels

GSA AO2



© 2018, AIS, Inc.

NON-POWERED AIR FLOW / WALL ACCESS PANELSH W Model Number List Grade C Paint Data KO C.O.M Fabric Grade C Fabric Grade D Fabric39 24 P-HEFOBR3924 802 +10 +15 -37 +70 +136

39 30 P-HEFOBR3930 877 +10 +15 -37 +70 +136

39 36 P-HEFOBR3936 986 +10 +15 -37 +70 +136

39 42 P-HEFOBR3942 1,042 +10 +15 -37 +70 +136

39 48 P-HEFOBR3948 1,089 +10 +15 -37 +70 +136

39 60 P-HEFOBR3960 1,353 +10 +15 -37 +70 +136

47 24 P-HEFOBR4724 848 +10 +15 -47 +80 +160

47 30 P-HEFOBR4730 946 +10 +15 -47 +80 +160

47 36 P-HEFOBR4736 1,081 +10 +15 -47 +80 +160

47 42 P-HEFOBR4742 1,198 +10 +15 -47 +80 +160

47 48 P-HEFOBR4748 1,234 +10 +15 -47 +80 +160

47 60 P-HEFOBR4760 1,516 +10 +15 -47 +80 +160

53 24 P-HEFOBR5324 865 +10 +15 -57 +86 +166

53 30 P-HEFOBR5330 985 +10 +15 -57 +86 +166

53 36 P-HEFOBR5336 1,149 +10 +15 -57 +86 +166

53 42 P-HEFOBR5342 1,238 +10 +15 -57 +86 +166

53 48 P-HEFOBR5348 1,325 +10 +15 -57 +86 +166

53 60 P-HEFOBR5360 1,624 +10 +15 -57 +86 +166

Specify Notes


Non-Powered Panels - Air Flow / Wall Access are fabric covered hard surface panels. Panels may be ordered with power/data access base covers and/or raceway divider. Each panel includes all connection hinges needed for each panel. Air Flow / Wall Access Panels have a 3” fabric border around the opening that allows for air flow. The height of the opening is 16”.

PANELSNon-Powered Air Flow / Wall Access Panels

GSA AO2



NON-POWERED AIR FLOW / WALL ACCESS PANELSH W Model Number List Grade C Paint Data KO C.O.M Fabric Grade C Fabric Grade D Fabric67 24 P-HEFOBR6724 1,012 +10 +15 -57 +100 +190

67 30 P-HEFOBR6730 1,133 +10 +15 -57 +100 +190

67 36 P-HEFOBR6736 1,307 +10 +15 -57 +100 +190

67 42 P-HEFOBR6742 1,393 +10 +15 -57 +100 +190

67 48 P-HEFOBR6748 1,485 +10 +15 -57 +100 +190

67 60 P-HEFOBR6760 1,829 +10 +15 -57 +100 +190

85 24 P-HEFOBR8524 1,193 +10 +15 -94 +120 +226

85 30 P-HEFOBR8530 1,327 +10 +15 -94 +120 +226

85 36 P-HEFOBR8536 1,528 +10 +15 -94 +120 +226

85 42 P-HEFOBR8542 1,623 +10 +15 -94 +120 +226

85 48 P-HEFOBR8548 1,724 +10 +15 -94 +120 +226

Specify Notes


Non-Powered Panels - Air Flow / Wall Access are fabric covered hard surface panels. Panels may be ordered with power/data access base covers and/or raceway divider. Each panel includes all connection hinges needed for each panel. Air Flow / Wall Access Panels have a 3” fabric border around the opening that allows for air flow. The height of the opening is 16”.

PANELSNon-Powered Air Flow / Wall Access Panels

GSA AO2



© 2018, AIS, Inc.

Specify Notes


Powered Panels - Air Flow / Wall Access are fabric covered hard surface panels with a powered raceway unit. Duplex outlets and electrical jumpers are ordered separately. See “Electrical”. Two duplex outlet hole covers are included with each powered panel. Air Flow / Wall Access Panels have a 3” fabric border around the opening that allows for air flow. The height of the opening is 16”.

POWERED AIR FLOW / WALL ACCESS PANELSH W Model Number List Grade C Paint C.O.M Fabric Grade C Fabric Grade D Fabric39 24 P-HEFOBP3924 1,191 +10 -37 +70 +136

39 30 P-HEFOBP3930 1,261 +10 -37 +70 +136

39 36 P-HEFOBP3936 1,369 +10 -37 +70 +136

39 42 P-HEFOBP3942 1,424 +10 -37 +70 +136

39 48 P-HEFOBP3948 1,474 +10 -37 +70 +136

39 60 P-HEFOBP3960 1,726 +10 -37 +70 +136

47 24 P-HEFOBP4724 1,235 +10 -47 +80 +160

47 30 P-HEFOBP4730 1,332 +10 -47 +80 +160

47 36 P-HEFOBP4736 1,462 +10 -47 +80 +160

47 42 P-HEFOBP4742 1,578 +10 -47 +80 +160

47 48 P-HEFOBP4748 1,613 +10 -47 +80 +160

47 60 P-HEFOBP4760 1,896 +10 -47 +80 +160

53 24 P-HEFOBP5324 1,254 +10 -57 +86 +166

53 30 P-HEFOBP5330 1,366 +10 -57 +86 +166

53 36 P-HEFOBP5336 1,532 +10 -57 +86 +166

53 42 P-HEFOBP5342 1,616 +10 -57 +86 +166

53 48 P-HEFOBP5348 1,699 +10 -57 +86 +166

53 60 P-HEFOBP5360 1,994 +10 -57 +86 +166

PANELSPowered Air Flow / Wall Access Panels

GSA AO2



Specify Notes


Powered Panels - Air Flow / Wall Access are fabric covered hard surface panels with a powered raceway unit. Duplex outlets and electrical jumpers are ordered separately. See “Electrical”. Two duplex outlet hole covers are included with each powered panel. Air Flow / Wall Access Panels have a 3” fabric border around the opening that allows for air flow. The height of the opening is 16”.

POWERED AIR FLOW / WALL ACCESS PANELSH W Model Number List Grade C Paint C.O.M Fabric Grade C Fabric Grade D Fabric67 24 P-HEFOBP6724 1,393 +10 -57 +100 +190

67 30 P-HEFOBP6730 1,510 +10 -57 +100 +190

67 36 P-HEFOBP6736 1,687 +10 -57 +100 +190

67 42 P-HEFOBP6742 1,768 +10 -57 +100 +190

67 48 P-HEFOBP6748 1,856 +10 -57 +100 +190

67 60 P-HEFOBP6760 2,197 +10 -57 +100 +190

85 24 P-HEFOBP8524 1,573 +10 -94 +120 +226

85 30 P-HEFOBP8530 1,699 +10 -94 +120 +226

85 36 P-HEFOBP8536 1,900 +10 -94 +120 +226

85 42 P-HEFOBP8542 1,994 +10 -94 +120 +226

85 48 P-HEFOBP8548 2,096 +10 -94 +120 +226

PANELSPowered Air Flow / Wall Access Panels

GSA AO2



© 2018, AIS, Inc.

ADA DOOR PANELS

H W Type Model Number List

Grade C Panel Trim

Grade C Door Paint

85 48 Left P-HEDLA8548 2,585 +10 +100

85 48 Right P-HEDRA8548 2,585 +10 +100

Specify Notes

• Paint Selection for Door and Door Frame

• Style Selection for Tem-pered Glass Insert

ADA Door Panels use a steel tube frame with hol-low core door, stainless steel threshold, locking ADA door handle and full height transparent window. In-cludes one panel, one locking ADA lockset, and two keys. Lockset is field installed. Panel connectors are ordered separately.

ADA GLASS WINDOW DOOR PANELS

H W Type Model Number List

Grade C Panel Trim

Grade C Door Paint

85 48 Left P-HEDLAG8548 4,851 +10 +100

85 48 Right P-HEDRAG8548 4,851 +10 +100

Specify Notes

• Paint Selection for Door and Door Frame

• Style Selection for Tempered Glass Insert

ADA Glass Window Door Panels use a steel tube frame with hollow core door, stainless steel threshold, locking ADA door handle and full height transparent window. In-cludes one panel, one locking ADA lockset, and two keys. Lockset is field installed. Panel connectors are ordered separately. Note: Door has a 5” wood painted border around the glass.

Left Hand Right Hand

PANELSADA Door Panels

Left Hand Right Hand

GSA AO2



NON-LOCKING SLIDING DOORS

H W Model Number ListGrade C

Paint67 36 P-HMRPS6736 1,631 +25

67 42 P-HMRPS6742 1,753 +25

67 48 P-HMRPS6748 1,874 +25

85 36 P-HMRPS8536 1,874 +25

85 42 P-HMRPS8542 2,034 +25

85 48 P-HMRPS8548 2,175 +25

SLIDING DOOR HANDLE KITS

Model Number ListGrade C

PaintA-UNRPSH 169 +10

Specify Notes

• Paint Selection for Sliding Door Frame

Sliding Door attaches to frame face at either left or right, outside or inside of an opening. Sliding doors are available to accommodate 36”, 42” and 48” wide openings and are 67” or 85” high. Lightweight, alu-minum frame, painted as specified, with a ribbed lex-an insert. Sliding door extends 1 1/2” into opening when fully open and stands a total of 2” off panel face. These dimensions should be taken into consid-eration when planning for ADA door openings and aisle dimension requirements if door is mounted on outside of office.

CONNECTOR HILO TRIMH Model Number List66 P-HMHILO62 82

80 P-HMHILO80 115

PANELSSliding Doors

Front Back

Notes

Notes

When specifying sliding doors at a corner application, a 2-way connector and connector HiLo trim piece needs to be ordered in addition to the sliding door. This fills the 3 1/2” gap created in this scenario.

GSA AO2



© 2018, AIS, Inc.

STRAIGHT ROD CONNECTORSH Model Number List39 P-HMROD34/39 62

47 P-HMROD42/47 62

53 P-HMROD48/53 62

67 P-HMROD62/67 64

85 P-HMROD80/85 65

Notes

Straight Rod Connectors connect two panels of equal height in a straight line. See unequal straight rod connectors for connecting panels of unequal height in a straight line.

UNEQUAL HEIGHT STRAIGHT ROD CONNECTOR KITSDrop Down Model Number List Grade C Paint

85-67 P-HEHILOSK18 147 +5

85-53 P-HEHILOSK32 147 +5

85-47 P-HEHILOSK38 147 +5

85-39 P-HEHILOSK46 147 +5

67-53 P-HEHILOSK14 147 +5

67-47 P-HEHILOSK20 147 +5

67-39 P-HEHILOSK28 147 +5

53-47 P-HEHILOSK6 147 +5

53-39 P-HEHILOSK14A 147 +5

47-39 P-HEHILOSK8 147 +5

Specify Notes

• Paint Selection for HiLo Finishing Strip

Unequal Height Straight Rod Connector Kits con-nect two panels of unequal heights in a straight line. Includes one straight rod connector (which corre-sponds to the height of the low panel), one hanger frame (which corresponds to the height of the low panel), one HiLo finishing strip (finishes the side of the high panel above the HiLo connection), and HiLo finishing strip retainers

CONNECTORSStraight Rod Connectors

GSA AO2



2-WAY CONNECTORSH Model Number List Grade C Paint39 P-HECC39 172 +5

47 P-HECC47 190 +5

53 P-HECC53 194 +5

67 P-HECC67 209 +5

85 P-HECC85 245 +5

4-WAY CONNECTORSH Model Number List Grade C Paint39 P-HMXC34/39 231 +5

47 P-HMXC42/47 268 +5

53 P-HMXC48/53 278 +5

67 P-HMXC62/67 316 +5

85 P-HMXC80/85 345 +5

FINISHED END CAPSH Model Number List Grade C Paint39 P-HEEC39 81 +5

47 P-HEEC47 86 +5

53 P-HEEC53 90 +5

67 P-HEEC67 91 +5

85 P-HEEC85 106 +5

3-WAY CONNECTORSH Model Number List Grade C Paint39 P-HETC39 241 +5

47 P-HETC47 260 +5

53 P-HETC53 275 +5

67 P-HETC67 301 +5

85 P-HETC85 341 +5

Specify Notes

• Paint Selection for Con-nector Trim

• Color Selection for Base Shroud

2-Way Connectors connect two panels of equal or unequal heights at 90°. In HiLo scenarios, specify the connector height that corresponds to the tallest pan-el in the connection. HiLo finishing strips need to be ordered separately.

Specify Notes



3-Way Connectors connect three panels of equal or varying heights at 90°. In HiLo scenarios, specify the connector height that corresponds to the tallest pan-el in the connection. HiLo finishing strips need to be ordered separately.

Specify Notes


4-Way Connectors connect four panels of equal or varying heights at 90°. In HiLo scenarios, specify the connector height that corresponds to the tallest pan-el in the connection. HiLo finishing strips need to be ordered separately.

Specify Notes



Finished End Caps finish the end of a panel run where no other panels are to be connected. Includes base end cap shroud.

CONNECTORS2-Way Connectors, 3-Way Connectors, 4-Way Connectors and End Caps

GSA AO2



© 2018, AIS, Inc.

WALL MOUNT KITSH Model Number List Grade C Paint39 P-HMWM34/39 69 +5

47 P-HMWM42/47 72 +5

53 P-HMWM48/53 76 +5

67 P-HMWM62/67 79 +5

85 P-HMWM80/85 86 +5

HILO FINISHING STRIPSDrop Down Model Number List Grade C Paint

85-67 P-HMHILO18 59 +5

85-53 P-HMHILO32 59 +5

85-47 P-HMHILO38 71 +5

85-39 P-HMHILO46 71 +5

67-53 P-HMHILO14 44 +5

67-47 P-HMHILO20 59 +5

67-39 P-HMHILO28 59 +5

53-47 P-HMHILO6 59 +5

53-39 P-HMHILO14 44 +5

47-39 P-HMHILO8 59 +5

Specify Notes


Wall Mount Kits connect a panel to a fixed wall. In-cludes top and bottom connection blocks, one panel shell, and one filler strip. Hardware for attaching wall mount kit to wall is not included. Use hardware ap-propriate for wall type.

Specify Notes

• Paint Selection for HiLo Finishing Strip

HiLo Finishing Strips are used when 2-Way, 3-Way, or 4-Way connectors are connecting panels of varying heights. The HiLo finishing strip finishes the exposed side of the connector where a low panel is attached. For instance, if you have a 67”H 2-way connector with one of the panels being 47”H, order the HiLo finishing strip for a 67” to 47” drop down.

WALL TRACKSH Model Number List60 A-WTRK60HM 125

84 A-WTRK84HM 155

Notes

Wall Track mounts to fixed walls to provide a slotted channel for worksurface sup-port brackets, tackboards or shelves. Slots are on a 1” vertical repeat pattern. Wall track mounting holes are 1/4” diameter, repeating 6” on center starting 1/2” from top of the track. Note: Hardware for mounting wall track to walls is not included. Use hardware appropriate to wall type. Wall track may be shared between shelf units. Only three tracks are needed to hang two shelf units, flipper door units, or tackboards side by side. Wall tracks are composed of a black slotted insert rail within a brushed aluminum casing. Track will sit approximately 5” off floor when leveled with top of panels to accommodate wall cover base.

CONNECTORSWall Mount Kits, HiLo Finishing Trips and Wall Tracks

GSA AO2



ELECTRICALAO2 Electrical Product Details

Hot 1 (Black)

Hot 3 (Blue)

Metal Cable Jacket

Neutral 4 (White/Red) (#10g)

Ground 4 (Green/Yellow)

Hot 4 (Pink)

Hot 2 (Red)

Neutral 1/2/3 (White/Black) (#10g)

Ground 1/2/3 (Green)

Cross Section 8 Wire 4 Circuit Cable

AIS AO2 8 Wire 4 Circuit electrical system contains four circuits. Each circuit is rated at 20 amps/120 volts maximum. Circuit 1, Circuit 2 and Circuit 3 are served by a system neutral and an equipment ground. Circuit 4 is dedicated and is served by its own neutral and ground. Circuit and ground conductors are #12 A.G.W. (gauge). All neutrals are #10 A.G.W. (gauge).

Shown below is cross section of metal cable used for 8 Wire 4 Circuit jumpers and in-feeds. Circuit and ground conductors are #12 A.G.W. (gauge). All neutrals are #10 A.G.W. (gauge).

4D

Circuit 4 Hot Pink Wire

Circuit 1 Hot Black Wire

Circuit 1/2/3 Neutral White & Black Wire

Circuit 1/2/3 Ground Green Wire

Circuit 4 Ground Green & Yellow Wire

Circuit 4 Neutral White & Red Wire

Circuit 2 Hot Red Wire

Circuit 3 Hot Blue Wire

Hot

Gro

und

Neu

tral

Hot

Gro

und

Neu

tral

Hot

Gro

und

Neu

tral

Hot

Gro

und

Neu

tral

Line 1 Line 2 Line 3 Line 4

Jumper locking clip

Outlet mounting hole

1 Duplex outlet location

Powerway mounting holes

2 Duplex outlet locations

2 Jumper connection locations

2 Duplex outlet locations

8 Wire 4 Circuit Powerway for 36"w panel

8 Wire 4 Circuit Powerway for 24"w panel

1 Duplex outlet location




4D

Powerways provide electrical distribution and access for duplex outlets back to back. 24” wide panels can accept only one duplex outlet per side, two total back to back. All other panels can accept two per side, four total back to back. Powerways “grow” in length with panels of greater width, making panel to panel connections a “standard” configuration and allowing for “pass through” connections. Each powerway has locations for up to four jumpers, two at each end. Powerways are included when ordering powered panels.

Duplex Outlets are available designated circuits 1 thru 4. Each duplex outlet contains two single receptacles (places to plug into) of the same circuit and are specified separately from powerways. All duplex outlets have black faces. The lettering on outlets for Circuit 1, 2 and 3 is white. The lettering on outlets for Circuit 4 is orange. Outlets are screw mounted to powerway. Duplex outlets are standard 15 amp outlets. For 20 amp outlets, call AIS Customer Service.

Common Equipment Amperages:Personal Computer ..... 2.00 - 4.00Laser Printer ................ 5.00 - 8.00 Desktop Plotter ........... 1.50Fan .............................. 1.00Heater .......................... 8.50 - 12.50Tasklight ...................... 1.00Slide Projector ............. 2.00 - 6.00Coffee Pot ....................15.00Paper Shredder ........... 4.40 - 13.00Radio ........................... 0.05Pencil Sharpener ......... 1.00Calculator .................... 0.25Answering Machine ..... 0.08

Product Detail 1Electrical Components (8 Wire, 4 Circuit)

GSA AO2



© 2018, AIS, Inc.

ELECTRICALAO2 Electrical Product Details

1. Grip Attachment Strip:72” length can be cut to fit and bolted to pole and ceiling grid with hardware provided.

2. Pole Cover:Snaps in place to seal vertical channels.

3. Divider:Attached to pole shell threaded studs with rounded safety “acorn” nuts. Divider may be mounted on centered or 60/40 split to accommodate more data cables.

4. Pole Coupler:Slides into both halves of pole. Four threaded screws are tightened to form rigid pressure fit.

5. Mounting Brackets:Engage opposed on panel hanger frames to lock lower section of pole to panel. Bracket threaded studs and rounded safety “acorn” nuts attach pole to brackets.

6. Pole Shell:Relived on one end to provide means of egress for data cables and ceiling feeds. Pole top and bottom section are identical.

Product Detail 2Double Channel Power/Data Pole

Product Detail 3Integrating AIS AO2 Power

1

2

3

4

5

5

Old AIS/Old HM New AIS


New AISNew AIS

New AISNew AIS

Old AIS/Old HMNew HM

New AISNew HM

New AISNew HM

18 inch Mesh Jumper(E-MX8W4PTPC18)

OEM Transition KitIncludes OEM Cable,ICon and 18 Jumper

(E-HM8W4TCK)

AO2 Panel

Powerway

18 inch mesh jumper

18 inch mesh jumper

18 inch mesh jumper

OEM CableOnly

OEM TransitionKit

OEM TransitionKit

21 inch mesh jumper

AIS AO2 Electrical Jumper Connections


OEM Transition Cable(E-HM8W4TC)



New AISNew AIS

New AISNew AIS


New AISNew HM

New AISNew HM



(E-HM8W4TCK)

AO2 Panel

Powerway

18 inch mesh jumper

18 inch mesh jumper

18 inch mesh jumper

OEM CableOnly

OEM TransitionKit

OEM TransitionKit

21 inch mesh jumper






New AISNew AIS

New AISNew AIS


New AISNew HM

New AISNew HM



(E-HM8W4TCK)

AO2 Panel

Powerway

18 inch mesh jumper

18 inch mesh jumper

18 inch mesh jumper

OEM CableOnly

OEM TransitionKit

OEM TransitionKit

21 inch mesh jumper






New AISNew AIS

New AISNew AIS


New AISNew HM

New AISNew HM



(E-HM8W4TCK)

AO2 Panel

Powerway

18 inch mesh jumper

18 inch mesh jumper

18 inch mesh jumper

OEM CableOnly

OEM TransitionKit

OEM TransitionKit

21 inch mesh jumper




GSA AO2



STANDARD PANEL-TO-PANEL JUMPERSL Model Number List

18 E-MX8W4PTPC18 150

21 E-MX8W4PTPC21 158

TRANSITIONAL JUMPERSType Model Number List

OEM Transition Kit E-HM8W4TCK 661

Notes

Panel-to-Panel Jumpers connect any two adjacent powered panels connected in a straight line or at a 90° angle. Order an Extended panel -to-panel jumper to connect any two powered panels across the gap created by a 3-way or 4-way connection. 90° corners and straight panel-to-panel connections do not require an extended jumper.

Notes

Lateral Pass Through Jumpers pass through a non-powered panel to connect two powered panels. Specify the jumper that corresponds to the width of the panel to be passed through. In extended pass through situations, specify the next lateral pass through jumper size in order to span the additional gap created by a 3-way or 4-way connection. 90° corners and straight panel-to-panel connections do not require an extended jumper. Specify the jumper that corresponds to the width of the panel to be passed through.

Notes

Transitional Jumpers connect any two adjacent powered panels with different versions of power connected in a straight line or at a 90° angle. See diagram on opposing page.

LATERAL PASS THROUGH JUMPERSPanel W Panel L Description Model Number List

12 37 Pass thru 12” panel E-MW8W4PJ18 200

12 Ext 37 Pass thru 12” panel extended E-MW8W4PJ18 200










48 Ext 69 Pass thru 48” panel extended E-MW8W4PJ48E 271


60 Ext 86 Pass thru 60” panel extended E-HM8W4PJ60E 303

ELECTRICALJumpers

GSA AO2

34 Electronic Libraries available at 2020.net and ProjectMatrix.comPhone: 800.434.7400 Fax: 978.562.0811 Web: www.ais-inc.com

Revision Dec 2018© 2018, AIS, Inc.

DUPLEX OUTLETSLine Model Number List

1 E-HM8W4OUT1 54

2 E-HM8W4OUT2 54

3 E-HM8W4OUT3 54

4 E-HM8W4OUT4 54

5 E-HM8W4OUT5 99

Notes

Duplex Outlets are available designated circuits 1 through 4. Each duplex outlet contains two single receptacles (places to plug into) of the same circuit and are specifi ed separately from powerways. All duplex outlets have black faces. The lettering on outlets for Circuit 1, 2 and 3 is white. The lettering on outlets for Circuit 4 and 5 is orange. Outlets are screw mounted to powerway. Duplex outlets are standard 15 amp outlets.

Notes

In California, 50 percent of all outlets in a systems panel cluster or benching clus-ter, for new construction, MUST be controlled outlets, even if there is no task lighting. Customers should plan on using circuits 2 and 3 for controlled circuits, and plan general load for all other items on circuits 1 and 4. If using 2 + 2 confi g-uration, controlled circuits should be 1 and 2, and general load circuits on 4 and 5. Outlets must have the “controlled” symbol for identifi cation purposes.

CALIFORNIA TITLE 24 CONTROLLED DUPLEX OUTLETSLine Model Number List

1 E-HM8W4T24DO1 58

2 E-HM8W4T24DO2 58

3 E-HM8W4T24DO3 58

4 E-HM8W4T24DO4 58

“Controlled” Symbol

Notes

USB Outlets bring USB charging options to panel power distribution systems. The USB Outlets provide convenient charging power access through dual ports on the face of the receptacle. The USB Outlets off er a total of 2 Amps between two USB charging ports. The USB Outlets are UL and FCC Part 15A approved.

USB OUTLETSLine Model Number List

1 E-UN8W4USB01 225

2 E-UN8W4USB02 225

3 E-UN8W4USB03 225

4 E-UN8W4USB04 225

DUPLEX OUTLET HOLE COVERSModel Number List

E-UNWC 20

Specify Notes

• Color Selection for Hole Cover

Duplex Outlet Hole Covers are supplied with each powered panel to cover unused duplex outlet loca-tions (six). 24”W panels only include three duplex outlet hole covers. Order extra hole covers separate-ly only when required.

ELECTRICALDuplex Outlets

GSA AO2



RECEPTACLE MOUNTED BASE IN-FEEDSHand L Model Number ListLeft 72 E-UN8W4BIFL 364

Right 72 E-UN8W4BIFR 364

NEW YORK CITY RECEPTACLE MOUNTED BASE IN-FEEDSHand L Model Number ListLeft 72 E-HM8W4BIFLNY 709

Right 72 E-HM8W4BIFRNY 709

SIDE MOUNTED BASE IN-FEEDSL Model Number List

72 E-UN8W4BIFS 338

NEW YORK CITY SIDE MOUNTED BASE IN-FEEDSL Model Number List

72 E-HM8W4BIFSNY 676

Notes

Side Mounted Base In-Feeds provide interface with building power at the base of the panel and mounts to powerway at jumper location. Each base feed is 6’ in length, encased in “liquid tight”. New York City code requires the use of a special base feed with an in-line junction box.

Notes

Receptacle Mounted Base In-Feeds provide interface with building power and mounts to powerway at duplex outlet location. Each base in-feed is 6’ in length, encased in “liquid tight”. New York City code requires the use of a special base feed with an in-line junction box.

Notes

Receptacle Mounted Base In-Feeds provide interface with building power and mounts to powerway at duplex outlet location. Each base in-feed is 6’ in length, encased in “liquid tight”. New York City code requires the use of a special base feed with an in-line junction box.

CEILING IN-FEEDSL Model Number List

144 E-UN8W4CIF 412

Notes

Ceiling In-Feeds provide interface with building power from a suspended ceiling through a power pole shell. Each ceiling feed is 12’ long. Power pole shells are ordered separately.

Notes

New York City Side Mounted Base In-Feeds provide interface with building power and mounts to side of powerway. Each base feed is 6’ in length, encased in “liquid tight”. New York City code requires the use of a special base feed with an in-line junction box.

ELECTRICALIn-Feeds

GSA AO2



© 2018, AIS, Inc.

ELECTRICAL RETROFIT KITSW Model Number List24 E-FRKHEP8424 280

30 E-FRKHEP8430 301

36 E-FRKHEP8436 313

42 E-FRKHEP8442 332

48 E-FRKHEP8448 348

60 E-FRKHEP8460 379

Specify Notes

• Color Selection for Base Cover

Electrical Retrofit Kits are for field retrofitting existing non-powered AIS AO2 panels with 8 wire, 4 circuit electrical. Kit includes one powerway and mounting screws, two powered base covers and two duplex outlet hole covers. Duplex outlets, jumpers, extra hole covers or feeds are ordered separately.

HARDWIRE JUNCTION BOXModel Number List

E-HMJBCH 215

Specify Notes

• Color Selection for Plate Covers

Hardwire Junction Box allows standard, hardwired, single gang duplex outlets to be used in AO2 pan-els at each standard, modular duplex outlet location. Each outlet will require one junction box; however, outlets can be placed back to back on a spine, with a total of two outlets total per box. Junction boxes do not include electrical connectors. Boxes are UL listed. Decora faced outlets cannot be used. Kit in-cludes all hardware required to attach box to AO2 panel at duplex outlet location. Standard AO2 pow-ered base covers are required. Order AO2 panels with Chicago base cover option. Boxes have stan-dard 0.875” knockouts for electrical connectors. Junction boxes can be used with either 15 amp or 20 amp single gang outlets.

DATA PLATE KITSItem Model Number List

6 Port Data Gang Plate E-DP6GFPB 24

CAT 5e Jack (RJ-45) E-HRJ45-SM 85

CAT 6 Data Jack E-HXJ6BK-SM 94

Hole Blank (10 PK) E-SFBB10-SM 56

Notes

Snap-In Data Housing Plate has six ports. Housing is black and snaps into stan-dard AIS AO2 duplex outlet holes, which measure 1.86” x 3.012”. RJ-45 jacks can be used in place of RJ-11 jacks.

ELECTRICALRetrofit Kits, Power/Data Pole Kits, Junction Boxes, Data Plate Kits

DOUBLE CHANNEL POWER/DATA POLE KITModel Number List Grade C PaintA-PPDCHM 516 +20

Specify Notes

• Paint Selection Double Channel Power/Data Pole Kit includes two 68” pole sections, two 68” covers, one pole coupler, two 68” dividers, four pole to panel mounting brack-ets, one ceiling shroud, one 72” length of perforat-ed metal strip for attaching pole to ceiling grid, and mounting hardware. Order ceiling feeds separately. Designed for an 11’ ceiling.

GSA AO2



STANDARD CANTILEVERSSurface Depth

Actual Depth Hand Model Number List

Grade C Paint

24 18 Left WPS-HECT24L 67 +10

24 18 Right WPS-HECT24R 67 +10

24 18 Pair WPS-HECT24P 130 +20

30 25.5 Left WPS-CTLTL30 130 +10

30 25.5 Right WPS-CTLTR30 130 +10

30 25.5 Pair WPS-CTLT30 258 +20

Specify Notes

• Paint Selection for Can-tilevers

Standard Cantilevers provide cantilevered worksur-face support from panel or wall track at either the left or right hand side of a worksurface. All worksurface support components fasten directly to worksurfaces with screws. Standard cantilevers may also be used as a center support. Specify cantilever that corre-sponds to worksurface depth. It is highly recom-mended that flat plates are specified in conjunction with support cantilevers to splice two worksurfaces together at the front edge. Painted black as standard, all other trim colors are Grade C upcharged.

SHARED CANTILEVERSSurface Depth


Grade C Paint

24 18 Left WPS-HECT24SL 98 +10

24 18 Right WPS-HECT24SR 98 +10

24 18 Pair WPS-HECT24SP 191 +20

30 25.5 Left WPS-CTLST30L 189 +10

30 25.5 Right WPS-CTLST30R 189 +10

30 25.5 Pair WPS-CTLST30P 375 +20

Specify Notes

• Paint Selection for Can-tilevers

Shared Cantilevers provide cantilevered support from panel or wall track at seam between two work-surfaces. All worksurface support components fas-ten directly to worksurfaces with screws. Specify cantilever that corresponds to worksurface depth. It is highly recommended that flat plates are speci-fied in conjunction with support cantilevers to splice two worksurfaces together at the front edge. Painted black as standard, all other trim colors are Grade C upcharged.

SIDE SUPPORT / REAR BRACKETS

Hand Model Number ListGrade C

PaintLeft WPS-SSHML 47 +10

Right WPS-SSHMR 47 +10

Pair WPS-SSHM 93 +20

Specify Notes

• Paint Selection for Side Support / Rear Bracket

Side Support/Rear Brackets provide direct support from panel or wall track along short side of rectangu-lar worksurface or at rear of corner worksurface. All worksurface support components fasten directly to worksurfaces with screws. Painted black as a stan-dard. All other trim colors are Grade C upcharged.

PANEL MOUNTED SHELF CANTILEVERSSurface Depth


Grade C Paint

12 10 Left WPS-CT10PHEL 120 +10

12 10 Right WPS-CT10PHER 120 +10

12 10 Pair WPS-CT10PHE 231 +20

Specify Notes

• Paint Selection Panel Mounted Shelf Cantilevers are 10”d and de-signed to work in conjunction with 12”d worksurfac-es to create additional desk top shelving. Available for all AIS panel systems. For use with 12” to 16” worksurfaces only.

SUPPORTCantilevers and Side Support/Rear Brackets

RightLeft

GSA AO2



© 2018, AIS, Inc.

STANDARD END PANELS

D Model Number ListGrade C

Laminate12 WFS-EPHM12 256 +20

18 WFS-EPHM18 301 +24

24 WFS-EPHM24 340 +27

30 WFS-EPHM30 378 +30

36 WFS-EPHM36 430 +34

Specify Notes

• Laminate Selection for End Panel

• 2mm Edge Selection for End Panel

Standard End Panels have laminated vertical surfac-es and a 2mm PVC vertical front edge. Standard end panels provide direct support from floor at left or right side of a worksurface, and engage and lock to pan-els with provided mounting brackets. All worksurface support components fasten directly to worksurfaces with screws. Specify end panel that corresponds to worksurface depth.

CLEAR ACCESS END PANELS


Laminate24 WFS-EPCAHM24 358 +29

30 WFS-EPCAHM30 400 +32

Specify Notes

• Laminate Selection for End Panel

• 2mm Edge Selection for End Panel

Clear Access End Panels have laminated vertical sur-faces and a 2mm vertical front edge. Clear access end panels provide direct support from floor at left or right side of a worksurface, and engage and lock to panels with provided mounting brackets. All worksur-face support components fasten directly to worksur-faces with screws.

Specify Notes

• Paint Selection for Count-er-top Bracket

Countertop Brackets provide direct support from 41”H panel for countertop worksurfaces. Specify at least two pair of countertop brackets for every coun-tertop (one pair for front side and one pair for rear). All worksurface support components fasten directly to worksurfaces with screws.

COUNTERTOP BRACKETS

Hand Model Number ListGrade C

PaintLeft WPS-CTBLHM 44 +10

Right WPS-CTBRHM 44 +10

Pair WPS-CTBHM 84 +20

PEDESTAL-TO-PEDESTAL ATTACHMENT BRACKET

Model Number ListGrade C

LaminateS-HMPMPB 167 +25

Specify Notes

• Paint Selection Pedestal-to-Panel Attachment Brackets attach structural pedestals to panels. These brackets serve as a space filler and as a way to add stability to pan-els..Pedestal to panel attachment brackets may only be used when the nominal surface depth matches the nominal pedestal depth (24” Deep surface & 24” deep pedestal or 30” deep surface and 30” deep pedestal).

SUPPORTEnd Panels and Brackets

GSA AO2



PANEL MOUNTED A-LEGS

H D Hand Model Number ListGrade C

Paint27 12 Left WFS-ALW2712AOL 309 +25

27 12 Left Shared WFS-ALW2712AOLS 332 +25

27 12 Right WFS-ALW2712AOR 309 +25

27 12 Right Shared WFS-ALW2712AORS 332 +25

27 12 Freestanding WFS-ALW2712FS 352 +25

27 24 Left WFS-ALW2724AOL 352 +25





27 30 Left WFS-ALW2730AOL 375 +25





Specify Notes

• Paint Selection A-Legs are constructed from 1” x 2” painted steel. Legs have 1 1/2” leveling glides. A-Leg welded construction allows for attachment to the worksurface. Panel attachment brackets are included and installed at the factory for panel mounted legs. Panel locking bracket for panel attachment situations ships separate. Freestanding A-Legs cannot be used as freestanding table support. One side must be anchored to a storage element or panel.

SUPPORTPanel Mounted A-Legs

Panel Mounted Left Hand Panel Mounted Left Hand Shared Panel Mounted Right Hand Panel Mounted Right Hand Shared Freestanding

GSA AO2



© 2018, AIS, Inc.

Specify Notes

• Paint Selection Mid-Height Shelf Units provide low profile overhead storage. Shelf ends have locking swing cams to pre-vent dislodgement. Shelf bottom will receive task-lights. Unit includes two mid-height shelf ends, one shelf pan, and mounting hardware. Order shelf unit that corresponds to panel width.

MID-HEIGHT SHELF UNITS

H W D Model Number ListGrade C

Paint7.75 24 12 S-SHFMX24 216 +12

7.75 30 12 S-SHFMX30 223 +12

7.75 36 12 S-SHFMX36 232 +12

7.75 42 12 S-SHFMX42 245 +12

7.75 48 12 S-SHFMX48 271 +12

7.75 60 12 S-SHFMX60 286 +12

LINEAR MID-HEIGHT SHELF UNITS


Paint7.75 24 12 S-SHFLMX24 213 +12

7.75 30 12 S-SHFLMX30 220 +12

7.75 36 12 S-SHFLMX36 229 +12

7.75 42 12 S-SHFLMX42 241 +12

7.75 48 12 S-SHFLMX48 266 +12

7.75 60 12 S-SHFLMX60 283 +12

Specify Notes

• Paint Selection Linear Mid-Height Shelf Units provide low profile overhead storage. Shelf ends have locking swing cams to prevent dislodgement. Shelf bottom will re-ceive tasklights. Unit includes two Linear Mid-height shelf ends, one shelf pan, and mounting hardware. Order shelf unit that corresponds to panel width.

SHELF DIVIDERSModel Number List Grade C PaintS-SHFDIV12 97 +10

Specify Notes

• Paint Selection Shelf Divider mounts to mid-height shelf decks and may also be used inside of complete flipper bins. No hardware necessary. Divider snaps into place. Divid-er is 5 5/8” tall and designed to finish at the same height as a mid-height shelf end.

STORAGEMid-Height Shelf Units

GSA AO2



MID-HEIGHT CORNER SHELF UNITS

H WCenter

DWing


Paint7.75 36 30.5 12 S-SHFCMX36 900 +25

7.75 42 30.5 12 S-SHFCMX42 995 +25

7.75 48 30.5 12 S-SHFCMX48 1,215 +25

Specify Notes

• Paint Selection Mid-Height Corner Shelf Units provide low profile overhead storage in corner above corner worksur-faces. Shelf ends have locking swing cams to pre-vent dislodgement. Shelf has lateral strength bar welded parallel to front edge which will receive a 36” or smaller tasklight parallel to front edge. All shelves 33 5/8” across front edge and are 30 1/2” deep front to back corner. Back corner has 3 1/2” x 3 1/2” cut-out to facilitate cable management. 42” and 48” units have 6” and 12” wings respectively. Unit includes two mid-height shelf ends, one bottom shelf pan, two corner shelf back mounting brackets, and mounting hardware. Order shelf unit that corresponds to panel width.

LINEAR MID-HEIGHT CORNER SHELF UNITS

H WCenter

DWing


Paint7.75 36 30.5 12 S-SHFLCMX36 906 +25

7.75 42 30.5 12 S-SHFLCMX42 964 +25

7.75 48 30.5 12 S-SHFLCMX48 1,358 +25

Specify Notes

• Paint Selection Linear Mid-Height Corner Shelf Units provide low profile overhead storage in corner above corner worksurfaces. Shelf ends have locking swing cams to prevent dislodgement. Shelf has lateral strength bar welded parallel to front edge which will receive a 36” or smaller tasklight parallel to front edge. All shelves 33 5/8” across front edge and are 30 1/2” deep front to back corner. Back corner has 3 1/2” x 3 1/2” cutout to facilitate cable management. 42” and 48” units have 6” and 12” wings respectively. Unit in-cludes two Linear Mid-height shelf ends, one bottom shelf pan, two corner shelf back mounting brackets, and mounting hardware. Order shelf unit that corre-sponds to panel width.

SHELF DIVIDERSModel Number List Grade C PaintS-SHFDIV12 97 +10

Specify Notes

• Paint Selection Shelf Divider mounts to mid-height shelf decks and may also be used inside of complete flipper bins. No hardware necessary. Divider snaps into place. Divid-er is 5 5/8” tall and designed to finish at the same height as a mid-height shelf end.

STORAGEMid-Height Corner Shelf Units

GSA AO2



© 2018, AIS, Inc.

METAL / FABRIC DOOR FRONT TYPE C FLIPPER DOOR UNITSInterior

H WInterior


PaintC.O.MFabric

Grade CFabric

Grade DFabric

EasyDown

14.25 24 12 S-FDUMX24 560 +20 -5 +13 +24 +215

14.25 30 12 S-FDUMX30 572 +20 -5 +13 +24 +215

14.25 36 12 S-FDUMX36 590 +20 -5 +13 +24 +215

14.25 42 12 S-FDUMX42 603 +20 -5 +13 +24 +215

14.25 48 12 S-FDUMX48 641 +20 -5 +13 +24 +215

14.25 60 12 S-FDUMX60 779 +20 -5 +13 +24 +215

LAMINATE DOOR FRONT TYPE C FLIPPER DOOR UNITSInterior

H WInterior


PaintGrade C

LaminateEasyDown

14.25 24 12 S-FDUMX24L 694 +20 +17 +215

14.25 30 12 S-FDUMX30L 708 +20 +18 +215

14.25 36 12 S-FDUMX36L 724 +20 +19 +215

14.25 42 12 S-FDUMX42L 741 +20 +20 +215

14.25 48 12 S-FDUMX48L 824 +20 +21 +215

14.25 60 12 S-FDUMX60L 913 +20 +22 +215

Easy Down Mechanism (Optional)

Specify Notes

• Paint Selection• Paint or Fabric for Flipper Door Style• Fabric Selection for Flipper Selection (if applicable)

• Easy Down Mechanism (optional)

Type C Flipper Door Unit - Metal/Fabric Door Front provides binder height, lockable overhead storage. Door opens and stores above top cover pan. Flipper unit has an open back. Shelf ends have locking swing cams to prevent dislodgement. Shelf bot-tom will receive tasklights. Easy Down Mechanisms are optional for all sizes and recommended on 60” wide units. All flipper doors are lockable with two supplied keys. Lock cores are removable with removal keys and master keys are available. Extra lock cores are available for keying flipper doors alike, but flipper doors may not be ordered without locks. Keying flippers alike requires removal of pre-installed lock cores and installation of keyed alike cores in the field. Order flipper unit that corresponds to panel width. See “Accessories” for ordering replacement keys, master keys, core removal keys, additional keys cores for keying alike or replacement uses.

Specify Notes

• Paint Selection• Laminate Selection for Flipper Door• Edge Selection for Flipper Door• Easy Down Mechanism (optional)

Type C Flipper Door Unit - Laminate Door Front provides binder height, lockable overhead storage. Door opens and stores above top cover pan. Flipper unit has an open back. Shelf ends have locking swing cams to prevent dislodgement. Shelf bot-tom will receive tasklights. Easy Down Mechanisms are optional for all sizes and recommended on 60” wide units. All flipper doors are lockable with two supplied keys. Lock cores are removable with removal keys and master keys are available. Extra lock cores are available for keying flipper doors alike, but flipper doors may not be ordered without locks. Keying flippers alike requires removal of pre-installed lock cores and installation of keyed alike cores in the field. Order flipper unit that corresponds to panel width. See “Accessories” for ordering replacement keys, master keys, core removal keys, additional keys cores for keying alike or replacement uses.


STORAGEType C Flipper Door Units

GSA AO2



METAL / FABRIC DOOR FRONT TYPE C RAISED FLIPPER DOOR UNITSInterior

H WInterior


PaintC.O.MFabric

Grade CFabric

Grade DFabric

PerfBack

EasyDown

14.25 24 12 S-FDURFMX24 1,142 +20 -5 +13 +24 +35 +215

14.25 30 12 S-FDURFMX30 1,168 +20 -5 +13 +24 +35 +215

14.25 36 12 S-FDURFMX36 1,196 +20 -5 +13 +24 +35 +215

14.25 42 12 S-FDURFMX42 1,230 +20 -5 +13 +24 +35 +215

14.25 48 12 S-FDURFMX48 1,296 +20 -5 +13 +24 +35 +215

14.25 60 12 S-FDURFMX60 1,464 +20 -5 +13 +24 +35 +215


Specify Notes

• Paint Selection• Paint or Fabric for Flipper Door Style• Fabric Selection for Flipper Selection (if applicable)

• Metal or Perforated Back Panel Style• Easy Down Mechanism (optional)

Type C Raised Flipper Door Unit - Metal/Fabric Door Front provides binder height, lockable overhead storage. When mounted on 53” high panels, unit rests level with a standard flipper door unit mounted at the top of a 65” high panel. Door opens and stores above top cover pan. Backside of unit is completely enclosed providing added security. Shelf ends have locking swing cams to prevent dislodgement. Shelf bottom will receive tasklights. Easy down mechanisms are optional for all sizes and rec-ommended on 60” wide units. All flipper doors are lockable with two supplied keys. Lock cores are removable with removal keys and master keys are available. Extra lock cores are available for keying flipper doors alike, but flipper doors may not be ordered without locks. Keying flippers alike requires removal of pre-installed lock cores and installation of keyed alike cores in the field. Order flipper unit that corresponds to panel width. See “Accessories” for ordering replacement keys, master keys, core removal keys, additional keys cores for keying alike or replacement uses.

LAMINATE DOOR FRONT TYPE C RAISED FLIPPER DOOR UNITSInterior

H WInterior


PaintGrade C

LaminatePerfBack

EasyDown

14.25 24 12 S-FDURFMX24L 1,279 +20 +17 +35 +215

14.25 30 12 S-FDURFMX30L 1,304 +20 +18 +35 +215

14.25 36 12 S-FDURFMX36L 1,330 +20 +19 +35 +215

14.25 42 12 S-FDURFMX42L 1,367 +20 +20 +35 +215

14.25 48 12 S-FDURFMX48L 1,480 +20 +21 +35 +215

14.25 60 12 S-FDURFMX60L 1,603 +20 +22 +35 +215

Specify Notes

• Paint Selection• Laminate Selection for Flipper Door• Edge Selection for Flipper Door• Metal or Perforated Back Panel Style• Easy Down Mechanism (optional)

Type C Raised Flipper Door Unit - Laminate Door Front provides binder height, lockable overhead storage. When mounted on 53” high panels, unit rests level with a standard flipper door unit mounted at the top of a 65” high panel. Door opens and stores above top cover pan. Backside of unit is completely enclosed providing added security. Shelf ends have locking swing cams to prevent dislodgement. Shelf bottom will receive tasklights. Easy down mechanisms are optional for all sizes and rec-ommended on 60” wide units. All flipper doors are lockable with two supplied keys. Lock cores are removable with removal keys and master keys are available. Extra lock cores are available for keying flipper doors alike, but flipper doors may not be ordered without locks. Keying flippers alike requires removal of pre-installed lock cores and installation of keyed alike cores in the field. Order flipper unit that corresponds to panel width. See “Accessories” for ordering replacement keys, master keys, core removal keys, additional keys cores for keying alike or replacement uses.


STORAGEType C Raised Flipper Door Units

GSA AO2



© 2018, AIS, Inc.

SOLID METAL DOOR FRONT TYPE D FLIPPER DOOR UNITSInterior

H WInterior


PaintEasyDown

14.25 24 12 S-FDDSMX24 682 +20 +215

14.25 30 12 S-FDDSMX30 697 +20 +215

14.25 36 12 S-FDDSMX36 713 +20 +215

14.25 42 12 S-FDDSMX42 727 +20 +215

14.25 48 12 S-FDDSMX48 764 +20 +215


Specify Notes

• Paint Selection• Easy Down Mechanism (optional)

Type D Flipper Door Unit - Solid Metal Door Front provides binder height, lockable overhead storage. Door opens and stores above top cover pan. Flipper unit has an open back. Shelf ends have locking swing cams to prevent dislodgement. Shelf bot-tom will receive tasklights. Easy down mechanisms are optional for all sizes and recommended on 60” wide units. All flipper doors are lockable with two supplied keys. Lock cores are removable with removal keys and master keys are available. Extra lock cores are available for keying flipper doors alike, but flipper doors may not be ordered without locks. Keying flippers alike requires removal of pre-installed lock cores and installation of keyed alike cores in the field. Order flipper unit that corresponds to panel width. See “Accessories” for ordering replacement keys, master keys, core removal keys, additional key cores for keying alike or replacement uses.


Specify Notes

• Paint Selection• Metal or Perforated Back Panel Style• Easy Down Mechanism (optional)

Type D Raised Flipper Door Unit - Solid Metal Door Front provides binder height, lockable overhead storage. When mounted on 53” high panels, unit rests level with a standard flipper door unit mounted at the top of a 65” high panel. Door opens and stores above top cover pan. Backside of unit is completely enclosed providing added security. Shelf ends have locking swing cams to prevent dislodgement. Shelf bottom will receive tasklights. Easy down mechanisms are optional for all sizes and rec-ommended on 60” wide units. All flipper doors are lockable with two supplied keys. Lock cores are removable with removal keys and master keys are available. Extra lock cores are available for keying flipper doors alike, but flipper doors may not be ordered without locks. Keying flippers alike requires removal of pre-installed lock cores and installation of keyed alike cores in the field. Order flipper unit that corresponds to panel width. See “Accessories” for ordering replacement keys, master keys, core removal keys, additional key cores for keying alike or replacement uses.

SOLID METAL DOOR FRONT TYPE D RAISED FLIPPER DOOR UNITSInterior

H WInterior


PaintPerfBack

EasyDown

14.25 24 12 S-FDDRMX24 1,266 +20 +35 +215

14.25 30 12 S-FDDRMX30 1,292 +20 +35 +215

14.25 36 12 S-FDDRMX36 1,321 +20 +35 +215

14.25 42 12 S-FDDRMX42 1,355 +20 +35 +215

14.25 48 12 S-FDDRMX48 1,421 +20 +35 +215

STORAGEType D Flipper and Raised Flipper Door Units

GSA AO2



METAL DOOR FRONT SLIDING DOOR UNITS


Paint14.25 30 12 S-MSDOMX30 687 +20

14.25 36 12 S-MSDOMX36 704 +20

14.25 42 12 S-MSDOMX42 718 +20

14.25 48 12 S-MSDOMX48 756 +20

14.25 60 12 S-MSDOMX60 889 +20

LAMINATE DOOR FRONT SLIDING DOOR UNITS


PaintGrade C

Laminate14.25 30 12 S-MSDOMX30L 821 +20 +18

14.25 36 12 S-MSDOMX36L 837 +20 +19

14.25 42 12 S-MSDOMX42L 853 +20 +20

14.25 48 12 S-MSDOMX48L 935 +20 +21

14.25 60 12 S-MSDOMX60L 1,023 +20 +22

Specify Notes

• Paint Selection Sliding Door Unit - Metal Door Front provides binder height, lockable overhead storage. Door slides open side to side. Sliding door unit has an open back. Shelf ends have locking swing cams to prevent dislodge-ment. Shelf bottom will receive tasklights. All slid-ing doors are lockable with (2) keys supplied. Lock cores are removable with removal keys and master keys are available. Extra lock cores are available for keying sliding doors alike, but sliding doors may not be ordered without locks. Keying sliding doors alike requires removal of pre-installed lock cores and in-stallation of keyed alike cores in the field. See “Ac-cessories” for shelf, flipper and key accessories.

Specify Notes

• Paint Selection• Laminate Selection for Sliding Door

• Edge Selection for Sliding Door

Sliding Door Unit - Laminate Door Front provides binder height, lockable overhead storage. Door slides open side to side. Sliding door unit has an open back. Shelf ends have locking swing cams to prevent dislodgement. Shelf bottom will receive tasklights. All sliding doors are lockable with (2) keys supplied. Lock cores are removable with removal keys and master keys are available. Extra lock cores are available for keying sliding doors alike, but slid-ing doors may not be ordered without locks. Keying sliding doors alike requires removal of pre-installed lock cores and installation of keyed alike cores in the field. See “Accessories” for shelf, flipper and key ac-cessories.

STORAGESliding Door Units

GSA AO2



© 2018, AIS, Inc.

METAL DOOR FRONT RAISED SLIDING DOOR UNITS


PaintPerforated

Back14.25 30 12 S-RMSDOMX30 1,293 +20 +35

14.25 36 12 S-RMSDOMX36 1,322 +20 +35

14.25 42 12 S-RMSDOMX42 1,356 +20 +35

14.25 48 12 S-RMSDOMX48 1,422 +20 +35

14.25 60 12 S-RMSDOMX60 1,589 +20 +35

Specify Notes

• Paint Selection Type C Raised Sliding Door Unit - Metal Door Front provides binder height, lockable overhead storage. When mounted on 50” high panels, unit rests level with a standard flipper door unit mounted at the top of a 66” high panel. Door slides open side to side. Backside of unit is completely enclosed providing added security. Shelf ends have locking swing cams to prevent dislodgement. Shelf bottom will receive tasklights. All sliding doors are lockable with (2) keys supplied. Lock cores are removable with removal keys and master keys are available. Extra lock cores are available for keying sliding doors alike, but slid-ing doors may not be ordered without locks. Keying sliding doors alike requires removal of pre-installed lock cores and installation of keyed alike cores in the field. See “Accessories” for shelf, flipper and key ac-cessories.

LAMINATE DOOR FRONT RAISED SLIDING DOOR UNITS


PaintGrade C

LaminatePerforated

Back14.25 30 12 S-RMSDOMX30L 1,427 +20 +18 +35

14.25 36 12 S-RMSDOMX36L 1,456 +20 +19 +35

14.25 42 12 S-RMSDOMX42L 1,490 +20 +20 +35

14.25 48 12 S-RMSDOMX48L 1,605 +20 +21 +35

14.25 60 12 S-RMSDOMX60L 1,727 +20 +22 +35

Specify Notes

• Paint Selection• Laminate Selection for Sliding Door

• Edge Selection for Sliding Door

Type C Raised Sliding Door Unit - Laminate Door Front provides binder height, lockable overhead storage. When mounted on 50” high panels, unit rests level with a standard flipper door unit mount-ed at the top of a 66” high panel. Door slides open side to side. Backside of unit is completely enclosed providing added security. Shelf ends have locking swing cams to prevent dislodgement. Shelf bottom will receive tasklights. All sliding doors are lockable with (2) keys supplied. Lock cores are removable with removal keys and master keys are available. Ex-tra lock cores are available for keying sliding doors alike, but sliding doors may not be ordered without locks. Keying sliding doors alike requires removal of pre-installed lock cores and installation of keyed alike cores in the field. See “Accessories” for shelf, flipper and key accessories.

STORAGERaised Sliding Door Units

GSA AO2



METAL DOOR FRONT CABINET DOOR UNITS


Paint14.25 24 12 S-VDOMX24 928 +20

14.25 30 12 S-VDOMX30 941 +20

14.25 36 12 S-VDOMX36 958 +20

14.25 42 12 S-VDOMX42 972 +20

14.25 48 12 S-VDOMX48 1,012 +20

Specify Notes

• Paint Selection Cabinet Door Unit - Metal Door Front provides bind-er height, lockable overhead storage. Doors swing open. Cabinet door unit has an open back. Shelf ends have locking swing cams to prevent dislodgement. Shelf bottom will receive tasklights. Units are lock-able with (2) keys supplied. Lock cores are removable with removal keys and master keys are available. Ex-tra lock cores are available for keying sliding doors alike, but sliding doors may not be ordered without locks. Keying sliding doors alike requires removal of pre-installed lock cores and installation of keyed alike cores in the field. See “Accessories” for shelf, flipper and key accessories.

Specify Notes

• Paint Selection• Laminate Selection for Cabinet Door

• Edge Selection for Cabi-net Door

Cabinet Door Unit - Laminate Door Front provides binder height, lockable overhead storage. Doors swing open. Cabinet door unit has an open back. Shelf ends have locking swing cams to prevent dis-lodgement. Shelf bottom will receive tasklights. Units are lockable with (2) keys supplied. Lock cores are removable with removal keys and master keys are available. Extra lock cores are available for keying sliding doors alike, but sliding doors may not be ordered without locks. Keying sliding doors alike re-quires removal of pre-installed lock cores and instal-lation of keyed alike cores in the field. See “Accesso-ries” for shelf, flipper and key accessories.

LAMINATE DOOR FRONT CABINET DOOR UNITS


PaintPerforated

Back14.25 24 12 S-VDOMX24L 1,063 +20 +17

14.25 30 12 S-VDOMX30L 1,078 +20 +18

14.25 36 12 S-VDOMX36L 1,092 +20 +19

14.25 42 12 S-VDOMX42L 1,110 +20 +20

14.25 48 12 S-VDOMX48L 1,192 +20 +21

STORAGECabinet Door Units

GSA AO2



© 2018, AIS, Inc.

METAL DOOR FRONT RAISED CABINET DOOR UNITS


PaintPerforated

Back14.25 24 12 S-RVDOMX24 1,490 +20 +35

14.25 30 12 S-RVDOMX30 1,516 +20 +35

14.25 36 12 S-RVDOMX36 1,545 +20 +35

14.25 42 12 S-RVDOMX42 1,578 +20 +35

14.25 48 12 S-RVDOMX48 1,642 +20 +35

Specify Notes

• Paint Selection Raised Cabinet Door Unit - Metal Door Front pro-vides binder height, lockable overhead storage. Doors swing open. Cabinet door unit has an open back. Shelf ends have locking swing cams to pre-vent dislodgement. Shelf bottom will receive task-lights. Units are lockable with (2) keys supplied. Lock cores are removable with removal keys and master keys are available. Extra lock cores are available for keying sliding doors alike, but sliding doors may not be ordered without locks. Keying sliding doors alike requires removal of pre-installed lock cores and in-stallation of keyed alike cores in the field. See “Ac-cessories” for shelf, flipper and key accessories.

LAMINATE DOOR FRONT RAISED CABINET DOOR UNITS


PaintGrade C

LaminatePerforated

Back14.25 24 12 S-RVDOMX24L 1,624 +20 +17 +35

14.25 30 12 S-RVDOMX30L 1,648 +20 +18 +35

14.25 36 12 S-RVDOMX36L 1,677 +20 +19 +35

14.25 42 12 S-RVDOMX42L 1,711 +20 +20 +35

14.25 48 12 S-RVDOMX48L 1,823 +20 +21 +35

Specify Notes

• Paint Selection• Laminate Selection for Cabinet Door

• Edge Selection for Cabi-net Door

Raised Cabinet Door Unit - Laminate Door Front provides binder height, lockable overhead storage. Doors swing open. Cabinet door unit has an open back. Shelf ends have locking swing cams to pre-vent dislodgement. Shelf bottom will receive task-lights. Units are lockable with (2) keys supplied. Lock cores are removable with removal keys and master keys are available. Extra lock cores are available for keying sliding doors alike, but sliding doors may not be ordered without locks. Keying sliding doors alike requires removal of pre-installed lock cores and in-stallation of keyed alike cores in the field. See “Ac-cessories” for shelf, flipper and key accessories.

STORAGERaised Cabinet Door Units

GSA AO2



TACKBOARDS

H W Model Number ListC.O.M Fabric

Grade C Fabric

Grade D Fabric

12 24 A-TACKHE1224 182 -5 +13 +24

12 30 A-TACKHE1230 191 -5 +13 +24

12 36 A-TACKHE1236 200 -5 +13 +24

12 42 A-TACKHE1242 211 -5 +13 +24

12 48 A-TACKHE1248 224 -5 +13 +24

12 60 A-TACKHE1260 293 -5 +13 +24

15 24 A-TACKHE1524 185 -5 +13 +24

15 30 A-TACKHE1530 196 -5 +13 +24

15 36 A-TACKHE1536 203 -5 +13 +24

15 42 A-TACKHE1542 217 -5 +13 +24

15 48 A-TACKHE1548 228 -5 +13 +24

15 60 A-TACKHE1560 300 -5 +13 +24

19 24 A-TACKHE1924 236 -5 +13 +24

19 30 A-TACKHE1930 251 -5 +13 +24

19 36 A-TACKHE1936 263 -5 +13 +24

19 42 A-TACKHE1942 277 -5 +13 +24

19 48 A-TACKHE1948 293 -5 +13 +24

19 60 A-TACKHE1960 314 -5 +13 +24

Specify Notes

• Fabric Selection Tackboards are 7/8” thick and mount to wall track to provide vertical tackable surface for wall track appli-cations and private offices. Tackboards are available in three different heights.

Specify Notes

• Paint Selection Tool Rail Kits mount to wall track or panel and ac-commodate paper flow elements. Tool rail kits are painted black as a standard. All other trim colors are Grade C upcharged.

TOOL RAIL KITS


Paint3.375 24 A-TBHM24 248 +20

3.375 30 A-TBHM30 272 +20

3.375 36 A-TBHM36 301 +20

3.375 42 A-TBHM42 320 +20

3.375 48 A-TBHM48 337 +20

3.375 60 A-TBHM60 498 +20

PANEL COAT HOOKSModel Number List Grade C Paint

A-CHM 48 +5

Specify Notes

• Paint Selection Panel Coat Hook mounts over top of panel and is available in all standard panel colors.

ACCSESSORIESTackboards, Tool Rail Kits and Panel Coat Hooks

GSA AO2



© 2018, AIS, Inc.

FRAMELESS WHITEBOARDS WITH MARKER TRAY

H W Model Number List24 24 A-FWBHM2424 391

24 30 A-FWBHM2430 365

24 36 A-FWBHM2436 409

24 42 A-FWBHM2442 454

24 48 A-FWBHM2448 469

24 60 A-FWBHM2460 551

30 24 A-FWBHM3024 344

30 30 A-FWBHM3030 396

30 36 A-FWBHM3036 448

30 42 A-FWBHM3042 499

30 48 A-FWBHM3048 551

30 60 A-FWBHM3060 656

Notes

Frameless White Boards with Markey Tray is a .6” thick laminated white board with 1mm white edgeband on all sides. Frameless White Boards mount to panels with standard brackets (included). Marker Tray is included and available in black only. Marker Tray is field installed.

WHITE BOARDS WITH MARKER TRAY


Paint24 24 A-WBHM2424 430 +15

24 30 A-WBHM2430 450 +15

24 36 A-WBHM2436 472 +15

24 42 A-WBHM2442 494 +15

24 48 A-WBHM2448 541 +15

24 60 A-WBHM2460 662 +15

30 24 A-WBHM3024 450 +15

30 30 A-WBHM3030 479 +15

30 36 A-WBHM3036 507 +15

30 42 A-WBHM3042 559 +15

30 48 A-WBHM3048 588 +15

30 60 A-WBHM3060 726 +15

Specify Notes

• Paint Selection for White-board

White Boards mount to panels with standard brack-ets. Marker Tray is included and available in black only. Marker Tray is field installed.

ACCESSORIESWhiteboards

GSA AO2

National Showrooms:

LeominsterAIS Headquarters25 Tucker DriveLeominster, MA 01453

For additional information on AIS:Dealer Showrooms, Representative Directory, Project Case Studies, Online Catalog & Product Showcase Visit: www.ais-inc.com

New YorkAIS New York257 Park Avenue SouthNew York, New York 10010

Washington, D.C.AIS Washington, D.C.1400 I St, NW, Suite 750Washington, D.C. 20005

ChicagoThe Merchandise MartSuite 1086Chicago, Illinois 60654

GSA SalesGSA Contract GS-29F-0006KFSC Group 71, Part 1 Office Furniture

800.434.7400 | 978.562.7500 | Fax: 978.562.0811 | www.ais-inc.com | December 2018

Documents

GSA AO2 - AISP 3 F 2 W ww.ais-inc.com Revision Dec 2018 ... AO2 Statement of Line 5 AO2 Finish Options 7 PANELS AO2 Panels Product Details 9 Non-Powered Hard Surface Panels 12 Powered