Hand Protection... · EN374-2 Resistance to penetration by micro- ... 0 denotes a fail and X denotes no test. OTHER HAND PROTECTION STANDARDS FOOD HANDLING ... The HPT process creates

3

4

The Personal Protective Equipment Directives (89/686/CEE) and (93/68/CEE) have been enacted by the European Community to ensure harmonisation of regulations regarding testing of all PPE sold within the community.

All gloves of intermediate and complex design must now be tested independently to ascertain their performance and ensure their safety. They must, if they meet these standards, carry a CE Mark on the gloves, or on their packaging when this is not practical.

CATEGORISATIONUnder the terms of the above directive, gloves fall into the following three categories:

CAT I - Simple DesignFor minimal risks only. Suitable only for low risk applications where hazards can be identifi ed by the wearer in time to deal with them.

CAT II - Intermediate DesignReversible risks. Products are type examined by an approved body where they examine the manufacturers technical specifi cations and conduct tests for the relevant standards to ascertain their conformity and/or performance.

CAT III - Complex DesignFor protection against mortal danger or risks of irreversible harm. Products are type examined by an approved body as for category II. In addition, the products and manufacturer are subject to EC quality control according to an approved quality system.

A detailed guide to EN standards is on Page 52

EUROPEAN STANDARDS (ENs)

GENERAL REQUIREMENTS EN420

Defi nes the general requirements for most types of protective gloves including:• Design and construction• Suitability for purpose• Sizing• Comfort and effi ciency• Innocuousness

Ratings

MECHANICAL HAZARDS EN388

a b c d

Resistance to abrasionBlade cut resistanceTear resistancePuncture resistance

0-40-50-40-4

THERMAL (HEAT) HAZARDS EN407

a b c def

Resistance to fl amabilityContact heat resistanceConvective heat resistanceRadiant heat resistanceResistance to small molten metal splashResistance to large molten metal splash

0-40-40-40-40-40-4

ANTISTATIC

New EN1149 standard

No pictogram is to be shown

PassorFail

CHEMICAL AND MICRO-ORGANISMS EN374

EN374-2 Resistance to penetration by micro-organisms.Referred to as acceptable quality level (AQL).

1-3

EN374-3 Resistance to chemical hazards - permeation

1-6

PROTECTION FROM COLD EN511

a. b. c.

Resistance to convective coldResistance to contact coldPermeability of water

0-40-40-1

When scores are given, the higher the score the better the performance. 0 denotes a fail and X denotes no test.

OTHER HAND PROTECTION STANDARDS

FOOD HANDLING

RADIOACTIVE CONTAMINATION

IONISING RADIATION

LOW CHEMICAL RESISTANT

Identifi cation of manufacturer

Size

Glove designation

Approved body number

The CE mark

SKYTECNINJA LITE

9/L

98/0120

CHEMICAL RESISTANCE PERMEATION

In compliance with EN374 Standard, the breakthrough time is given as a permeation index according to the following table:

The breakthrough time (in minutes) of a chemical through the glove is measured in conditions simulating a total immersion of the glove in the chemical at 23˚C. The gloves scoring the highest index have the best resistance to permeation. Index 0 denotes breakthrough time is less than 10 minutes.

Breakthrough timehigher than (in minutes)

10 30 60 120 240 480

Permeation index 1 2 3 4 5 6

5

Skytec offers a wide range of liners and coatings. Compare the strengths of each and choose the compositions that best meet your needs!

NylonA lightweight elastic polyamide which is largely lint-free and washable, dries quickly and is resistant to abrasion and deformation. When mixed with cotton and acrylic, it makes the glove more fl exible and extends its lifetime.

LatexNatural rubber that is supple, elastic, robust, highly resistant to mechanical impacts and hazards. Waterproof and detergent-safe.

Polyurethane (PU)Elastomer that is resistant to wear, abrasion, tearing and harsh oils and chemicals. Does not go hard in the cold or soft in the heat. It is microporous and provides the hand with ventilation. It is very elastic and adapts to all of the hand’s movements.

HPPEHigh performance polyethylene is fl exible, light and durable. As resistant to cutting as a para-aramid but with more resistance to abrasion, the fi bre remains resistant to chemicals, in particular solvents.

NitrileA hard-wearing synthetic polymer. Flexible and can withstand abrasion and puncturing, with maximum resistance to oil with enhanced grip.

CottonNatural Cellulose fi bre. Supple, soft, non-irritating, it provides protection from mechanical hazards, absorbs perspiration and makes continuous wearing of dipped protective gloves very comfortable.

HPTHydropellent Technology coating. The HPT process creates a spongy, soft and durable coating that repels liquids to provide a fi rm wet or dry grip. Encapsulated air molecules provide an inherent vibration absorption feature.

Para-aramidA para-aramid is lightweight, supple, comfortable, and washable. It provides effective protection from cuts, typically levels 4 and 5, and offers durability and performance that far exceeds leather.

APGNew patent pending Neoprene Bi-Polymer coating. Flexible, light and durable it provides great comfort and wearer satisfaction. Rough, chipped fi nish provides excellent grip in dry and wet applications. Solvent free process, silicone free formulation, and protein free. Excellent oil repellency.

NFTNitrile Foam Technology, a unique nitrile foam coating that is made by a Patented manufacturing process, offering breathability and dexterity along with excellent oil and wet grip properties.

Nitrile SpongeA patent pending micro-foam coating with excellent durability, and aiding breathability for long-term comfort. Unique micropore technology limits ingress of oils and greases.

6

APG

APG

APG

APG

Skytec provide the very best in all-round, multi-purpose hand protection, to protect the hand from common mechanical or chemical hazards while preserving mobility and dexterity.

Whether the job calls for small parts handling, general maintenance or heavy lifting and contractor work, we have the best glove for the job.

8

Order No.SKY051SKY052SKY053SKY054

EN388: 2003

Precision operations

Light engineering

Component assembly

Packaging

Warehousing and distribution

Seamless nylon liner with a HPT foam coated palm

Exceptional grip in wet and dry conditions

Foam coating has encapsulated air molecules that provides an inherent cushioning effect

A durable glove with excellent flexibility and tactile touch

Anatomically designed for comfort, dexterity and fit

Breathable back of hand to reduce perspiration and skin irritation

Resistant to abrasion and tearing

Lint free and silicone free

Black colouring to hide soiling

Treated with Actifresh to kill bacteria and promote freshness

9

Order No.SKY061SKY062SKY063SKY064SKY065

Seamless nylon liner with a ¾ HPT foam coating

A ¾ coated version of the Ohio glove for extra durability

Unique HPT foam coating with encapsulated air molecules that provides an inherent cushioning effect

Exceptional grip in wet and dry conditions

Anatomically designed for comfort, dexterity and fi t

Resistant to abrasion and tearing

Durable and cost effective

Lint free and silicone free




Light engineering

Component assembly

Packaging


Oil and gas

EN388: 2003

10


Construction

Handling rough objects

Wire and cable handling

Handling castings or pre-fabricated metals

Handling steel bars

Cotton liner with a full, crinkle fi nish latex coating

A durable and mechanically strong grip glove, suitable for heavy duty tasks

Excellent grip in wet and dry environments

Abrasion and tear resistance

Comfortable fi t with a knit wrist for extra protection

Anti-bacterial treatment to reduce odours

Blue and red colouring

EN388: 2003

11


Seamless nylon/spandex liner

Anatomically engineered for maximum fi t, superior comfort and dexterity

An Oeko-Tex® certifi ed product

Patented NFTTM nitrile foam palm coating enhances protection

Excellent grip in wet and dry conditions

Enhanced lifecycle through increased resistance to abrasion and tearing

Grey and black aesthetics for extended use


Automotive

Quality inspection

Goods handling

Assembly

Maintenance

Light fabrication

EN388: 2003

12



Optics

Component assembly

Packaging

Printed circuits and electronics

Surveying and Quality Inspection

18gg seamless nylon/lycra liner with a polyurethane coated palm

An ultra-lightweight glove, with exceptional fl exibility and tactile touch for the most delicate of tasks

‘Second skin’ dexterity provides superior sensitivity and comfort

Breathable through front and back of the hand to reduce perspiration and skin irritation

Elasticated wrist for a secure fi t

Lint free, reducing the risk of product contamination

Blue and black colouring


EN388: 2003

13

Light engineering

Component assembly

Construction

DIY



Seamless nylon/spandex liner with an ultra-light latex coated palm

The lightweight nylon/lycra liner (15gg) maintains a superthin ‘feel’ for improved dexterity, fi t and comfort


Abrasion and tear resistant

Anatomically designed for high levels of comfort and tactile touch

Breathable back of the hand to reduce perspiration and skin irritation


Silicone and lint free

Red and grey colouring


EN388: 2003

14

Manufacturing

Construction

Assembly

Automotive

General maintenance

Ceiling fi xing

Seamless nylon liner with a PU coated palm

Ideal for precision tasks requiring dexterity and fl exibility

Comfortable with anatomical shaped fi t, allowing excellent freedom of movement and reduction of hand fatigue

Abrasion and tear resistant, with a secure grip





Basalt R Order No.SKY410SKY411SKY412SKY413SKY414SKY415

Quartz Order No.-SKY441SKY442SKY443SKY444Available to order

EN388: 2003

15

Order No.SKY300SKY301SKY302SKY303SKY304SKY305

Manufacturing

Construction

Assembly

Automotive

General maintenance

Seamless nylon liner with a PU coated palm

Ideal for precision tasks requiring dexterity and fl exibility

Comfortable with anatomical shaped fi t, allowing excellent freedom of movement and reduction of hand fatigue

Abrasion and tear resistant, with a secure grip




Grey colouring

EN388: 2003

16


Automotive

Quality Inspection

Goods handling

Assembly and Maintenance

Light fabrication

Handling mild abrasive surfaces

18gg seamless liner glove with solid knit wrist

One of the lightest gloves in the industry for maximum comfort

Patented NFTTM nitrile foam coating for better grip in wet, oily and dry conditions

Excellent resistance to abrasion

Flexible and comfortable

Excellent dexterity

Red colouring


EN388: 2003

17

Ultra-lightweight 18gg liner provides unrivalled dexterity and fi t allowing users to wear for longer periods

Rough fi nish provides incredible grip in all environments

Solvent free manufacturing process

Silicone and latex protein free

Exceptional abrasion resistance compared to PU, Foam Nitrile and Latex coatings

Excellent oil repellency

Dark blue and black colouring




Light engineering

Component assembly

Packaging


Oil and gas

Aerospace

Automotive

EN388: 2003

18

Automotive

Aerospace


General assembly

Transport and distribution

Engineering


Seamless nylon liner with a nitrile foam coated palm

Excellent protection and grip in wet, oily and dry environments

Coating works with moisture to provide a superb grip

Anatomically designed for high levels of comfort and dexterity

Offers the user fl exibility and a tactile touch



Silicone free

White and grey colouring


EN388: 2003

19

Construction

Automotive assembly


Plastics manufacture

Handling castings or pre-fabrication


Seamless nylon liner with a nitrile coated palm

A secure grip with excellent fl exibility and tactile touch

A durable glove, tear and abrasion resistant

Anatomically designed to follow the natural curve of the hand and help reduce hand fatigue




White and dark green colouring

EN388: 2003

20

Cotton liner with a lightweight nitrile coated palm and knuckles

Durable with an excellent grip

Warm and comfortable to wear

Knitted wrist for a secure fi t


Ideal for dirty tasks

Yellow colouring for increased visibility

EN388: 2003

Construction

Engineering

Maintenance

Public works

Packaging

Neon Order No.SKY241SKY242SKY243SKY244

Neon Xtra Order No.-SKY222SKY223SKY224

More than 80-percent of all hand and arm injuries are due to cuts and lacerations. We make gloves and protective sleeves that not only resist cuts, but are also comfortable to wear, ensuring compliance as well as safety.

High levels of dexterity and grip are also essential in the prevention of cuts. Our pioneering designs and innovations lead the fi eld for these applications with next generation solutions.

22

Engineering

Glass industries

Component assembly

Packaging

Bottling or canning

Ceiling fi xing

Final fi x internal construction work

Seamless HPPE liner with a PU coated palm

A supple and light glove, with level 3 cut and puncture protection

Outstanding fl exibility and tactile touch

Excellent grip in both wet and dry environments

High abrasion and tear resistance

Anatomically designed for comfort, dexterity and fi t

Breathable knitted liner to reduce perspiration and skin irritation


Mottled grey colouring


Cirrus Order No.SKY461SKY462SKY463SKY464

Veritas Order No.SKY451SKY452SKY453SKY454

EN388: 2003

23

Engineering

Glass industries

Final fi x internal construction

Automotive

Metal fabrication


HPPE/lycra liner with APG palm coating

Combined technology offering ultimate precision cut resistant performance

Flexible, light glove providing protection against cuts with high levels of resistance to abrasion and tears

Rough fi nish allows objects and tools to be gripped fi rmly in both dry and wet applications

Solvent and silicone free manufacturing process



24

Automotive

Light fabrication

Goods handling

Assembly

Maintenance

Construction


HPPE liner

Sponge nitrile palm coating (patent pending)

Micro-capillaries draw liquids away from the surface providing better grip in all applications

Ventilated liner keeps hand cool to reduce perspiration and skin irritation


Amber colouring


ip

n

EN388: 2003

25

Glass industry

Castings

Sheet metal handling

Automotive

Aerospace

Order No.JSK10HJSK14HJSK18H

Double-ply medium weight sleeve

Para-aramid fi bres in the knit of the sleeve provide cut level 3 resistance

Thumbhole prevents slipping and wrist exposure

Gives increased protection from cuts, slash, tear and certain puncture

Comfortable and protective, the seamless knitted liner avoids skin irritation and is elasticated for extra protection

Machine washable

Available in three lengths: 10”, 14”, 18”

Yellow colouring

EN388: 2003

26


Engineering

Glass industries

Component assembly

Packaging

Bottling or canning

Seamless nylon/glass fi bre liner with a unique bi-polymer coated palm

A supple and light glove, with cut level 4 resistance


High abrasion and tear resistance

Anatomically designed to follow the natural curve of the hand and help reduce hand fatigue


Silicone free


Mottled grey and black colouring, suitable for the dirtiest of environments


EN388: 2003

27

Seamless HPPE and glass cut resistant liner with an advanced sponge nitrile (patent pending) palm coating

Excellent grip in wet, oily and dry conditions

Anatomically designed for comfort, dexterity and fi t - glove retains fl exibility despite its high protection levels



Green colouring for high visibility


Injection moulding

Glass industries

Engineering

Metal fabrication

Transport

Aerospace

Automotive



EN388: 2003

28


HPPE liner with APG palm coating

Maximum cut resistance at cut level 5

Flexible, lightweight glove providing maximum cut protection in dry, oily and greasy environments

Rough fi nish provides excellent grip in all environments

Enhanced durability due to good adhesion to the liner

Silicone and protein free, with a solvent free manufacturing process

Grey and black aesthetics for extended life


ry, oily and

ss

Injection moulding

Glass industries

Engineering

Metal fabrication

Transport

Aerospace

Automotive


EN388: 2003

29

Injection moulding

Glass industries

Engineering

Metal fabrication

Transport

Aerospace

Automotive


Seamless HPPE and glass liner with a bi-polymer coated palm

Maximum EN388 mechanical protection of 4-5-4-4

High durability and grip, with tear and abrasion resistance


Superb dexterity and sensitivity - even the most precise of task can be completed

Anatomically designed for comfort, dexterity and fi t, glove retains fl exibility despite its high protection levels


Grey and black colouring



EN388: 2003

30


Automotive

Mechanical inspection

Paint spraying

Metal fabrication

Transport

Seamless HPPE and glass liner with a PU coated palm

Maximum cut resistance at cut level 5


High durability with high tear and abrasion resistance

Anatomically designed for comfort, dexterity and fi t, glove retains fl exibility despite its high protection levels

Breathable to reduce perspiration and skin irritation


Mottled grey colouring


EN388: 2003

31

Order No.SKY0222SKY0223SKY0224

Wet and dry glass handling

Glass manufacture including soft coat


Injection or blow moulding

Machine shop work

Automotive

Seamless aramid/glass fi bre liner with leather palm

Lightweight, fl exible glove, para-aramid stitched for durability and strength

Soft, supple leather palm gives a water resistant grip and is suitable for oily conditions


Good dexterity and fl exibility together with high cut resistance

Anatomically designed for comfort and fi t

Elasticated wrist


Yellow and grey colouring

EN388: 2003

32


Injection moulding

Glass industries

Engineering

Wet and oily applications

Waste recycling

High risk handling

Fibre-Glass/HPPE liner with a full crinkle latex coating

Cut level 5 for maximum protection

Excellent mechanical performance and durability

Ultra-supple fully coated glove with a crinkled fi nish to ensure maximum grip in wet and dry conditions

The natural latex coating provides protection against oils, lubricants and contaminants

Anatomically designed for comfort, dexterity and fi t - the glove retains fl exibility without reducing high protection levels



EN388: 2003

33


EN388: 2003EN374-3

A K L

EN374-2

Offshore applications

Oil and gas cold storage

Maintenance

Utilities

Packaging


Light or heavy engineering

Glass handling and manufacture


Wet or oily applications

Cut resistant, seamless lined PVC gauntlet with a coral palm/knuckle coating (patent pending)

Cut level 5 resistant, enhanced protection from the double dipped PVC coating and special cut-resistant liner

Maximum durability and grip, with tear and abrasion resistance

Unique coral coating presents the wearer with secure grip in the most extreme environments, including chemical, oils and greases, and wet and dry conditions

Anatomically designed for comfort, dexterity and fi t - glove retains fl exibility despite its level of protection



The human body is in a comfortable situation when the heart is beating at a regular speed. This happens at an average blood temperature of 37° C. Using the right cold protection equipment is not a luxury. It will protect the wearer against cold blisters, slipping and excessive cold, while providing a satisfying level of comfort and protection.

Skytec gloves provide unrivalled levels of dexterity and fl exibility while retaining their performance in extreme conditions.

35


EN388: 2003

Oil industries


Glass industries

Heavy engineering

Paper/cardboard industries

Knitted seamless terry outer with a comfortable oil resistant coated nylon inner liner

Offers excellent protection, the outer absorbs oils to improve grip and feel whilst the inner liner protects against the ingress of contaminants

Excellent heat resistance and protection from the cold

Breathable nylon inner for reduced perspiration and skin irritation

Anatomically designed for comfort and fi t

Elasticated wrist

Knitted grey colouring


EN407 EN511

36



Maintenance

Utilities

Packaging

Double insulated nylon liner with a HPT foam ¾ coating

Durable glove that remains fl exible to temperatures as low as –50ºC

Secure grip in wet and dry environments

Additional foam coating across the palm, knuckles and fi ngers provides greater protection even in wet environments

Encapsulated air molecules provide an inherent cushioning effect

Warm and soft lining, anatomically designed for comfort and fi t

Excellent dexterity, fl exibility and durability

Silicone free




EN388: 2003 EN511

37


Utilities

Packaging



Maintenance

Double insulated Nylon liner with full PVC coating

Additional coral palm/knuckle coating (patent pending)

Excellent durability and grip in wet, oily and dry conditions

Durable glove that remains flexible to temperatures as low as -50˚C

Ideal for wet conditions

Enhanced protection from the double-dipped PVC coating

Encapsulated air molecules provide an inherent cushioning effect

Warm and soft lining, anatomically designed for comfort and fit

Silicone free



EN388: 2003 EN511

38

18gg seamless liner glove with solid knit wrist

One of the lightest gloves in the industry for maximum comfort

Patented NFTTM nitrile foam palm coating for better grip in wet, oily and dry conditions

Excellent dexterity

Cut level 3 glove with HPPE liner

Sponge nitrile palm coating (patent pending)

Micro-capillaries draw liquids away from the surface providing better grip in all applications

Ventilated liner keeps hand cool to reduce perspiration and skin irritation

Cut level 5 seamless HPPE and glass cut resistant liner with a sponge nitrile palm coating (patent pending)


Anatomically designed for comfort, dexterity and fi t - glove retains fl exibility despite its high protection levels


g)

39

Seamless nylon liner

Tough, fl exible unique patented Coral fi nish coating (patent pending), especially formulated to provide the highest level of grip


Flared gauntlet for ease of removal

Seamless HPPE liner

Cut level 3

Tough, fl exible unique Coral fi nish coating (patent pending), especially formulated to provide the highest level of grip


Seamless HPPE liner

Cut level 5



The Tricolore System of gloves and gauntlets is Skytec’s latest development. We continue to strengthen our product offering, and this exciting new range enables you to quickly and efficiently identify the correct glove for the job.

To protect the hands from direct contact with oils, hydrocarbons and corrosive substances, we provide the solutions to whatever conditions you may be working in.

Also of critical importance is the dexterity of the glove and the ability to correctly perform applications whilst wearing the gloves. Skytec have pioneered fl exible high dexterity chemical gloves thereby reducing the risk of chemical related accidents.

41

Order No.GLODAK01GLODAK02GLODAK03GLODAK04

Chemical handling

Petroleum and oil industry

Paintshop applications

Commercial printing

Agriculture and pesticide handling

NBR nitrile unsupported gauntlet

Flock lined for extra comfort and ease of donning

Textured palm and fi ngertips for grip in wet and dry conditions

Resistance to a wide variety of chemicals and solvents

EN374 and Category III approved

Chlorinated and sanitised to reduce odours

Straight cuff, 33cm in length

Green colouring

EN388: 2003 EN374-3 EN374-2

42

35cm gauntlet with a seamless nylon liner





35cm gauntlet with a seamless HPPE liner

Cut level 3





35cm gauntlet with a seamless double wall HPPE liner

Cut level 5





43

Order No.SKY593SKY594

Order No.SKY583SKY584

Chemical handling

Offshore oil and gas

Recycling / waste industry

Bottling and canning

Chemical handling


Recycling / waste industry

Bottling and canning

Chemical handling

Refining - oil and petrol


Maintenance


EN388: 2003

EN374-3

A K L

EN374-2

EN374-3

A K L

EN374-2

EN374-3

A K L

EN374-2

EN388: 2003

EN388: 2003

44

Refining - oil and petrol

Chemical handling

Agriculture and pesticide handling

Maintenance

100% cotton interlock liner with black APG full hand coating for exceptional grip

Combines the features of several synthetic materials to produce a CAT III gauntlet with true vice-like grip in wet, greasy and chemical envrionments

APG coating provides enhanced performance with greater comfort and wearer satisfaction

Superbly fl exible, comfortable and durable

35cm long gauntlet provides protection from a wide spectrum of chemicals and oils

Silicone and protein free, with a solvent free manufacturing process

Green and black colouring



EN388: 2003 EN374-3

A K L

EN374-2

45


EN388: 2003EN374-3

A K L

EN374-2



Maintenance

Utilities

Packaging


Light or heavy engineering

Glass handling and manufacture


Wet or oily applications

Cut resistant, seamless lined PVC gauntlet with a coral palm/knuckle coating (patent pending)

Cut level 5 resistant, enhanced protection from the double dipped PVC coating and special cut-resistant liner

Maximum durability and grip, with tear and abrasion resistance

Unique coral coating presents the wearer with secure grip in the most extreme environments, including chemical, oils and greases, and wet and dry conditions

Anatomically designed for comfort, dexterity and fi t, glove retains fl exibility despite its level of protection



Skytec is one of the most accomplished innovators and manufacturers of disposable hand protection.

Setting the standard for others to follow we continue to lead with high comfort and performance while cost in use remains low.

47

Commercial paint spraying


Laboratory work

Emergency services

Chemical applications

High performance NBR nitrile disposable gloves, non-sterile, powder-free

Textured fi nish for grip and touch

Resistant to oils, acids and many chemicals

Category III, EN374 and EN455 approved

Latex free

Comfortable with a ‘second skin’ feel

Signifi cantly stronger alternative to latex

AQL 1.5

Blue colouring

Order No.SKYUTAH1SKYUTAH2SKYUTAH3SKYUTAH4

EN374-3 EN374-2

48

Order No.SKYIRIS1SKYIRIS2SKYIRIS3SKYIRIS4



Laboratory work

Emergency services


High performance NBR nitrile disposable gloves, non-sterile, powder-free

Strong grip in wet and dry conditions



Latex and powder free to eliminate risk of contamination in food applications


Durable, high performance alternative to latex disposables

AQL 1.5

Rolled cuff for secure fi t

Distinctive colouring

EN374-3 EN374-2

49



Laboratory work

Emergency services


Premium performance NBR nitrile disposable gloves, non-sterile, powder-free

Textured fi nish for grip and touch

Greater chemical resistance and durability than normal nitrile disposable gloves



Latex free


Up to four times the puncture resistance of latex

AQL 1.5

Green colouring

Order No.SKYTEAL1SKYTEAL2SKYTEAL3SKYTEAL4

EN374-3 EN374-2

50

Product protection

Automotive

Laboratory work

Hair and beauty industry


High quality, low protein latex disposable gloves, non-sterile

Smooth finish with a high tensile strength

EN455 approved


Beaded cuff

AQL 1.5

Natural colouring

Order No.SKYIOWA1SKYIOWA2SKYIOWA3SKYIOWA4

51

Blue Order No.SKYMICHBL1SKYMICHBL2SKYMICHBL3SKYMICHBL4

Natural Order No.SKYMICHCL1SKYMICHCL2SKYMICHCL3SKYMICHCL4

Food manufacturer and handling

Product protection

Fabrication

Janitorial/Domestic work

High quality vinyl disposable gloves, non-sterile

Smooth finish with a high tensile strength


Powder free

Beaded cuff

AQL 4.0

Food handling approved

Clear and blue colouring available

52

The Single European Act includes a specifi c pledge to improve healthand safety at work for all European workers.

The commitment to ‘level up’ to the best practice currently employedwithin the Union has been enshrined in a legally binding FrameworkDirective (89/391/EEC), which not only lays down broad guidelines forhealth and safety but also places upon the employer an absolute duty“to ensure the safety and health of employees in their workplace”. Thisdirective is amplifi ed by fi ve daughter directives, of which one directlygoverns the use of protective gloves.

The Use of Personal Protective Equipment Directive 89/656/EECFour articles of the Directive merit particular attention, as they placesubstantial responsibilities on employers:

ARTICLE 3 states that before selecting any PPE, a basic assessmentmust be made to identify and evaluate the risk. Where possible, the riskmust be reduced or eliminated by a modifi cation of workplace practice.This option is always to be preferred to the use of PPE.

Under ARTICLE 4, the employer must inform his workers of the risksin the workplace, supply appropriate and correctly fi tting PPE whichcomplies with EU standards, and give adequate instruction in its use.He should further ensure that the PPE is used only for the purposeintended by the manufacturer, and in accordance with themanufacturer’s instructions.

ARTICLE 5 requires the employer to:1. Audit workplace hazards and assess the level of risk to employees.2. Defi ne the properties necessary in the gloves to protect the employees.3. Ensure that all gloves used in the workplace conform to the PPE Directive and relevant EN standards.4. Compare the merits of the various types of protection available.5. Keep full records of assessments and reasons for selecting a particular type of glove. If the risk should alter in any way, for instance by the introduction of a new chemical or industrial process, the assessment must be repeated.

Finally, ARTICLE 6 requires Member States to introduce written rulesfor workplace situations in which the use of PPE shall be consideredcompulsory. Naturally, employers will have to be aware of and complywith these rules.

To comply with the new regulations, you must select gloves which notonly adhere to the above Directive and relevant safety standards, butalso are demonstrably of good quality and fi ttest for the intended task.

COMPLYING WITH THE PPE DIRECTIVE: 89/686/EECThe Directive specifi es two classes of glove meeting two levels of risk:‘Minimal’ and ‘mortal’ or ‘irreversible’ risk. A risk which falls betweenthese two levels may be described as ‘intermediate’. To comply withthe 89/656/EEC Directive, you must establish the level of risk and selectgloves of the appropriate class.

A GREATER COMMITMENT TO HEALTH AND SAFETY EN STANDARDS FOR HAND PROTECTION

A system of marking has been developed to help you in that selection.

Gloves of simple design - for minimal risk onlyFor gloves of simple design offering protection from low level risks, e.g.janitorial gloves, manufacturers are permitted to test and certify glovesthemselves.

Gloves of this category are CE-marked as follows:

Gloves of intermediate design - for intermediate riskGloves designed to protect against intermediate risk, e.g. generalhandling gloves requiring good cut, puncture and abrasion performance,must be subjected to independent testing and certifi cation by a Notifi edBody. Only these approved Bodies may issue a CE mark, without whichthe gloves may not be sold. Each Notifi ed Body has its own identifi cationnumber. The name and address of the Notifi ed Body that certifi es theproduct has to appear on the instructions for use that will accompanythe gloves.

Gloves of intermediate design are CE-marked as follows:

Gloves of complex design - for irreversible or mortal riskGloves designed to protect against the highest levels of risk e.g.chemicals, must also be tested and certifi ed by a Notifi ed Body. Inaddition, the quality assurance system used by the manufacturer toguarantee homogeneity of production must be independently checked.The Body carrying out this evaluation will be identifi ed by a numberwhich must appear alongside the CE mark (in this case, 0120).

Gloves of complex design are CE-marked as follows:

Please note that the original PPE Directive 89/686/EEC has beenamended by both the 93/95/EEC Directive and the CE MarkingDirectives 93/68/EEC and 95/58 EEC.

RAISING STANDARDS IN EUROPEThe primary aim of the Personal Protective Equipment Directive is toimprove safety at work. This is achieved by establishing standards formanufacture and use that will apply throughout the Union; and thisis the remit of the Committee for European Normalisation (CEN). Thecommittee is made up of representatives of the national standardsorganisations in each of the Member States plus EFTA, along with majorEuropean PPE manufacturers.

If you would like any further clarifi cation of these Directives, or furtherinformation on testing and certifi cation procedures, please contact ourTechnical Service.

0120

53

SCOPEThis standard defi nes the general requirements for glove designand construction, innocuousness, comfort, effi ciency, marking andinformation applicable to all protective gloves. This standard can also apply to arm guards. The key points are given below. Some gloves designed for very specialist applications, such as electrician’s or surgical gloves are governed by other stringent job-specifi c standards (Details are available on request).

DEFINITIONA glove is an item of personal protective equipment which protects the hand or any part of the hand from hazards. It may also cover part of the forearm and arm. A performance level is a number (between 0 and 4) which shows how a glove has performed in a specifi c test, and by which the results of that testing may be graded. Level 0 indicates that the glove is either untested or falls below the minimum performance level. A performance level X means that the testing method is not suitable for the glove sample. Higher numbers indicate higher levels of performance.

GLOVE CONSTRUCTION AND DESIGN• Gloves have to offer the greatest degree of protection in the foreseeable conditions of end use.• When seams are included, the strength of these seams should not reduce the overall performance of the glove.

INNOCUOUSNESS• The gloves themselves shouldn’t cause any harm to the user• PH of the glove should be between 3.5 and 9.5• Chromium (VI) content should be below detection (<10 ppm)• Natural rubber gloves shall be tested on extractable proteins as per EN 455-3.

CLEANING INSTRUCTIONS• If care instructions are provided, the levels of performance should not be reduced after the maximum recommended number of cleaning cycles.

ELECTROSTATIC PROPERTIES• Antistatic gloves that are designed to reduce the risk of electrostatic discharges shall be tested as per EN 1149• Obtained test values are to be reported on the Instructions for Use• An electrostatic pictogram shall NOT be used

SIZING (SEE TABLE BELOW)• Gloves that are below the minimum length are to be called ‘Fit for Special Purpose’.

STANDARD EN 420: 2003GENERAL REQUIREMENTS FOR PROTECTIVE GLOVES

DEXTERITY• If required, performance to be graded as per table at the foot of the page.

WATER VAPOUR TRANSMISSION AND ABSORPTION• If required, gloves shall allow water vapour transmission (5mg cm2.h)• If gloves exclude water vapour transmission, it should be at least 8mg/cm2 for 8 hours.

MARKING & INFORMATION:Marking of the glove• Each glove should be marked with: - Name of manufacturer - Glove and size designation - CE mark - Appropriate pictograms accompanied by the relevant performance levels and the reference of the EN standard.

• The marking should be legible throughout the life of the glove. Where marking of the glove is not possible in view of the characteristics of the glove, it should be mentioned on the fi rst packaging enclosure.

Marking of the packaging immediately containing the gloves• Name and address of the manufacturer or representative• Glove and size designation• CE mark• Usage info - Simple design: “for minimal risks only” - Intermediate design or complex design: relevant pictograms - When protection is limited to part of the hand, this shall be mentioned (e.g. “Palm Protection style only”)• Reference to where information can be obtained

Instructions for Use (To be supplied when the glove is placed on the market)• Name and address of the manufacturer or representative• Glove designation• Size range available• CE mark• Care and storage instruction• Instructions and limitations of use• A list of substances used in the glove which are known to cause allergies• A list of all substances in the glove shall be made available upon request• Name and address of Notifi ed Body that certifi ed the product

SIZING OF GLOVESGlove size Fits hand size Hand circumference/length (mm) Minimum length of the glove (mm)

6 6 152/160 2207 7 178/171 2308 8 203/182 2409 9 229/192 25010 10 254/204 26011 11 279/215 270

Performance level Smallest diameter of pin that can be picked up with gloved hand 3 times/30 seconds (mm)1 11.02 9.53 8.04 6.55 5.0

54

SCOPEThis standard applies to gloves to protect from Ionising Radiation andRadioactive Contamination.

DEFINITION AND REQUIREMENTSThe nature of protection is shown by a pictogram relating to the specifi c protective qualities.• To protect from radioactive contamination, the glove has to be liquidproof and needs to pass the penetration test defi ned in EN 374.

STANDARD EN 421: 1994GLOVES GIVING PROTECTION FROM RADIOACTIVE CONTAMINATION AND IONISING RADIATION

• For gloves used in containment enclosures, the glove shall offer high resistance to permeability of water vapour.• To protect from ionising radiation, the glove has to contain a certain amount of lead, quoted as “lead equivalence”. This Lead Equivalence must be marked on each glove.• Materials exposed to ionising radiation may be modelled by their behaviour to ozone cracking. This test is optional and can be used as an aid to selecting gloves which require resistance to ionising radiation.

SCOPEThis standard applies to all kinds of protective gloves in respect ofphysical and mechanical aggressions caused by abrasion, blade cut,puncture and tearing.

DEFINITION AND REQUIREMENTSProtection against mechanical hazards is expressed by a pictogram followed by four numbers (performance levels), each representing test performance against a specifi c hazard.

STANDARD EN 388: 2003GLOVES GIVING PROTECTION FROM MECHANICAL RISKS

The ‘Mechanical Risks’ pictogram is accompanied by a 4-digit code:

a. Resistance to abrasion Based on the number of cycles required to abrade through the sample given.

b. Blade cut resistance Based on the number of cycles required to cut through the sample at a constant speed.

c. Tear resistance Based on the amount of force required to tear the sample.

d. Puncture resistance Based on the amount of force required to pierce the sample with a standard sized point.

In all cases, (0) indicates the lowest level of performance, as follows:

a b c d

EN388 TEST PERFORMANCE LEVEL RATING:0 1 2 3 4 5

a. Abrasion resistance (cycles) < 100 100 500 2000 8000

b. Blade cut resistance (factor) < 1.2 1.2 2.5 5.0 10.0 20.0

c. Tear resistance (newton) < 10 10 25 50 75

d. Puncture resistance (newton) < 20 20 60 100 150

These performance levels must be prominently displayed alongside the pictogram on the packaging which immediately contains the gloves.

55

SCOPEThis standard specifi es the capability of gloves to protect the useragainst chemicals and/or micro-organisms.

DEFINITIONS:PenetrationThe movement of a chemical and/or micro-organism through porousmaterials, seam, pinholes or other imperfections in a protective glovematerial at a non-molecular level.

PermeationThe rubber and plastic fi lms in gloves do not always act as barriers to

The ‘Chemical resistant’ glove pictogram must be accompanied by a 3-digit code. This code refers to 3 chemicals (from a list of 12 standard defi ned chemicals) for which a breakthrough time of at least 30 minutes has been obtained.

The ‘Low Chemical resistant’ or ‘Waterproof’ glove pictogram is to be used for those gloves that do not achieve a breakthrough time of at least 30 minutes against at least three chemicals from the defi ned list, but which comply with the Penetration test.

The ‘Micro-organism’ pictogram is to be used when the glove conforms to at least a performance level 2 for the Penetration test.

Warning: The chemical data information does not necessarily refl ect the actual duration in the workplace.

Permeation: Each chemical tested is classifi ed in terms of breakthrough time (performance level 0 to 6):

STANDARD EN 374: 2003GLOVES GIVING PROTECTION FROM CHEMICALS AND MICRO-ORGANISMS

liquids. Sometimes they can act as sponges, soaking up the liquidsand holding them against the skin. It is therefore necessary to measurebreakthrough times, or the time taken for the hazardous liquid to comein contact with the skin.

REQUIREMENTS• The minimum liquid proof section of the glove shall be at least equal to the minimum length of the glove specifi ed in EN 420.• Penetration: A glove shall not leak when tested to an air and/or water leak test, and shall be tested and inspected in compliance with the Acceptable Quality Level.

AQL: Performance level Acceptable quality level unit Inspection levels

Level 3 < 0.65 G1

Level 2 < 1.5 G1

Level 1 < 4.0 S4

Code Chemical CAS Number Class

A Methanol 67-56-1 Primary alcohol

B Acetone 67-64-1 Ketone

C Acetonitrile 75-05-8 Nitrile compound

D Dichloromethane 75-09-2 Chlorinated paraffi n

E Carbone disulphide 75-15-0 Sulphur containing Organic compound

F Toluene 108-88-3 Aromatic hydrocarbon

G Diethylamine 109-89-7 Amine

H Tetrahydrofurane 109-99-9 Heterocyclic and Ether compound

I Ethyl acetate 141-78-6 Ether

J N-Heptane 142-85-5 Saturated Hydrocarbon

K Sodium hydroxide 40% 1310-73-2 Inorganic base

L Sulphuric acid 96% 7664-93-9 Inorganic mineral acid

Measured breakthrough time Protection Index Measured breakthrough time Protection Index

> 10 minutes Class 1 > 120 minutes Class 4



A B C

56

SCOPEThis standard applies to any gloves to protect the hands againstconvective and contact cold down to -50oC.

DEFINITION AND REQUIREMENTSProtection against cold is expressed by a pictogram followed by a seriesof 3 performance levels, relating to specifi c protective qualities.The ‘cold hazard’ pictogram is accompanied by a 3-digit number:a. Resistance to convective cold (performance level 0 - 4)

b. Resistance to contact cold (performance level 0 - 4)

c. Permeability by water (0 or 1)

STANDARD EN 511: 1994GLOVES GIVING PROTECTION FROM COLD

All gloves must achieve at least EN388 performance level 1 for abrasionand tear.

• Convective cold resistance: based on the thermal insulation properties of the glove which are obtained by measuring the transfer of cold via convection.

• Contact cold resistance: based on the thermal resistance of the glove material when exposed to contact with a cold object.

• Water impermeability: 0 = water penetration after 30 minutes of exposure 1 = no water penetration.

A B C

SCOPEThis standard specifi es thermal performance for protective glovesagainst heat and/or fi re.

DEFINITION AND REQUIREMENTSThe nature and degree of protection is shown by a pictogram followed by a series of six performance levels, relating to specifi c protective qualities. Gloves must also achieve at least Performance level 1 for abrasion and tear.

The ‘heat and fl ame’ pictogram is accompanied by a 6-digit number:

a. Resistance to fl ammability (performance level 0-4) Based on the length of time the material continues to burn and glow after the source of ignition is removed. The seams of the glove shall not come apart after an ignition time of 15 seconds.

b. Contact heat resistance (performance level 0-4) Based on the temperature range (100-500oC) at which the user will feel no pain for at least 15 seconds. If an EN level 3 or higher is obtained, the product shall record at least EN level 3 in the fl ammability test Otherwise, the maximum contact heat level shall be reported as level 2.

STANDARD EN 407: 2004GLOVES GIVING PROTECTION FROM THERMAL HAZARDS

c. Convective heat resistance (performance level 0-4) Based on the length of time the glove is able to delay the transfer of heat from a fl ame. A performance level shall only be mentioned if a performance level of 3 or 4 is obtained in the fl ammability test.

d. Radiant heat resistance (performance level 0-4) Based on the length of time the glove is able to delay the transfer of heat when exposed to a radiant heat source. A performance level shall only be mentioned if a performance level 3 or 4 is obtained in the fl ammability test.

e. Resistance to small splashes of molten metal (performance level 0-4) The number of molten metal drops required to heat the glove sample to a given level. A performance level shall only be mentioned if a performance level 3 or 4 is obtained in the fl ammability test.

f. Resistance to large splashes of molten metal (performance level 0-4) The weight of molten metal required to cause smoothing or pinholing across a simulated skin placed directly behind the glove sample. The test is failed if metal droplets remain stuck to the glove material or if the specimen ignites.

a b c d e f

EN420 StandardThe way the glove fi ts the user is a crucial factor in the dexterity of the working hand. Here is all the information you need to make the right choice.

Testing prior to usingIf the glove is too small, it cuts off the blood circulation and restricts the movement of the hand. On the contrary, loose gloves slip off at the slightest movement and make your handling very imprecise. To be sure of your size and fi t contact Skytec.

Glove size further to EN420

Hand (mm) Glove

Palm circumference Length Minimum Length

6 152 160 220

7 178 170 230

8 203 182 240

9 229 192 250

10 254 204 260

11 279 215 270

57

Individual useTo prevent any risk of microbial, organic or chemical contamination, use of any glove should be ‘personal’ and not shared with other wearers, even after washing. (European directive 89/656/EEC).

Checking wearEach user must carefully monitor the condition of their gloves and replace them as soon as they lose the properties required for the task undertaken. This is notably the case for chemical protection gloves, which may show signs of excessive softening, becoming porous, brittle or displaying cracks when in contact with corrosive substances. This is normal but potentially harmful to hands, therefore precautions must be taken. (See box opposite).

WashingSkytec gloves can be washed at 40°C with a neutral detergent (pH ≥ 5), but the machine should not be fi lled completely as this affects the removal of soiling. Mechanical and/or chemical resistant properties typically remain after three washes but this depends on the degree of wear to the glove which must be checked.

Before putting on the gloves, wash and dry your hands carefully.

In the event of prolonged use, do not use gloves beyond the recommended exposure time as highlighted within a COSHH assessment.

Regularly check that the gloves have not become porous or are displaying any signs of degradation.

Where appropriate, folding the sleeve of the glove over slightly can help prevent substances coming into contact with arms.

Before removing gloves follow the advice on the user instructions.

When removing the second glove, do not touch the outside with the bare hand, but grip it by the inside of the sleeve. (Glove removal protocols are available from Globus upon request).

Before reusing gloves, check that they are dry both inside and out.

Your LogoYour DetailsYour Glove Range

A range of high-quality hand protection posters and charts, customised with your logo, details and product range - a genuine aid to worker compliance.

A Globus hand protection expert is available to assess your applications and current protection to provide guidance, advice and product evaluation without any requirement for commitment. This is a quick and easy way to validate or ensure the most suitable products are being utilised to deliver workers’ safety.

Globus will visit your workplace and conduct a comprehensive survey report. This will highlight areas of potential improvement, cost saving as well as developing a personalised plan that will incorporate all your aspirations, be they injury reduction, cost control or enhancing your ‘green’ credentials.

58

59

© 2012 Globus (Shetland) Ltd. This catalogue replaces all previously published catalogues and is the exclusive property of Globus (Shetland) Ltd. It may not be copied, duplicated or reproduced by any means without our expressed, written permission.

Globus (Shetland) Ltd, Globus Building, 38 Wheel Forge Way, Trafford Park, Manchester, M17 1EHwww.globus.co.uk

Documents

Hand Protection... · EN374-2 Resistance to penetration by micro- ... 0 denotes a fail and X denotes no test. OTHER HAND PROTECTION STANDARDS FOOD HANDLING ... The HPT process creates