HDHigh Speed Dome Camera

-2-

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK.

DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

DO NOT INSERT ANY MEALMETALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHERS

OPENINGS ON THE EQUIPMENT.

The lighting flash with arrowhead symbol, within a triangle, is intended to alert the userto the presence of un insulated dangerous voltage within the product enclosure thatmay be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to thepresence of important operating and maintenance (seervicing) instruction in the literatureaccompanying the product.

- WARNINGS AND CAUTIONS- PACAGE CONTENTS- INSTALLATION & CONFIGURATION -- Basic configuration of Dome -- Wall Mount Installation -- Ceiling Mount Installation -- Interface Cable Wiring- DIMENSION- OPERATION & PROGRAMMING -- Getting Started -- Basic Operations -- Menu Tree -- System : Information Reboot Factory Event Log Password -- Dispaly : OSD Setup Area Title Privacy Zone Image Setup Resulution -- Dome : General Motion Home Preset Tour Pattern Scan -- Camera : Focus / Zoom White Balance Exposure Advanced Setup System -- Alarm- SPECIFICATIONS

2 4

5 6 8 8 9

101011131415161718192021212223242526272829303132323334

-3-

- 4-

User’s Manual

User’s Manual

2

1. Carton Box2. PE Foam Bottom3. Camera Ass’y(with Sunshield-option)4. PE Foam Top5. Manual6. Anchor set(4set) Wrench / Screw plug / Screw

1. Dome camera Unit2. Body (W/O Sunshield)3. Trimring Bubble Dome4. Wrench-3mm5. User’s manual

1. Wall pipe Bracket2. Ceiling pipe Bracket3. Set Anchor (8set)4. Sunshield

Dome camera Unit

Body dome Ass’y Housing body(W/O sunshield)

Sunshield(Option)

Manual Wrench

TINT

COLOR

BRIGHT

CONT.

V1VOLUMEUNDERSCAN

S-VIDEOPOWER

V2

PMC14H

Video (HD-SDI)

HD-SDI Monitor

-5-

- 6-

1. Connect the dome camera unit to housing body Ass’y (Turn the 4ea of each screw to the right)

Wall Mount Bracket - Camera Set Assemble2. Remove the holder screw

3. When you assemble the dome bubble Ass’y Please follow up the picture.

4. Connect the dome bubble Ass’y to the housing body Ass’y

- 7-

1. Fix the TP 18x30L Screw supplied.2. Pass the cables through the bottom of the bracket.

3. Hang the safety hook against drop on the braket. Put the dome cable into the bracket and fix it.

5. Connect the camera cable to the bracket cable. Please see the cable connection. Close the bracket cover and fix it by knob bolt. Fix the steel cover supplied on the upper of the bracket using screw CM3x8L.

4. Fix the camera set by clockwise as the picture. Assemble the fixed screws using the wrench supplied.

Wall Mount Installtion

NO

2

1

Parts Name

Mount Screw

Wall Mount Bracket

DESCRIPTION

TP 18x30L

AL Diecasting

Q’ty

4

1

- 8 -

1. Fix the plastic anchors on the ceiling as this figure and fix the ceiling using the screws supplied. Fix the pipe supplied as this figure turning it clockwise.

2. Hang the hook against drop on the ceiling bracket as this figure, connect the camera and the bracket cable and fix it turning the camera set clockwise.

3. Assemble the fixed screws using the wrench supplied.

Ceiling Mount Installtion

TINT

COLOR

BRIGHT

CONT.

V1VOLUMEUNDERSCAN

S-VIDEOPOWER

V2

PMC14H

TINT

COLOR

BRIGHT

CONT.

V1VOLUMEUNDERSCAN

S-VIDEOPOWER

V2

PMC14H

NAME

ALARM 1

ALARM 2

ALARM 3

ALARM 4

NO

NC

NAME

232+

232-

485+

485-

LINE-OUT

LINE-IN

COLOR

BROWN /BLACK

RED / BLACK

ORANGE/ BLACK

BROWN

YELLOW / BLACK

BLUE / BLACK

COLOR

GRAY / BLACK

VIOLET / BLACK

GREEN

ORANGE

VIOLET

BLUE

No.

1

2

3

4

5

6

No.

7

8

9

10

11

12

HD-SDI (HD Monitor)

SUB Monitor

Power

No.

13

14

15

16

NAME

GND

GND

GND

COM

COLOR

GRAY

BLACK

BLACK / WHITE

GREEN / BLACK

- 9 -

DOME

WALL

CEILING

This manual is designed to be a reference tool for the installation, programming and operation of your system.

You need to install system before using this manual. Refer to <installation> part of this manual.

Once installed, apply power to the dome. The system will start a configuration sequence.

This information will remain on the monitor until dome operation begins. Refer to the following pages to operate and program your dome system.

NOTE.1. Version can be changed as system evolves.2. Address changes with respect to ‘address switching setting’3. Temperature can be changed as environment change

Basic Operations

How to Control

Pan and Tilt Move the joystick or press the direction keys left/right and up/down.

* Zoom Tele To zoom far, do the following: 1. Press the [TELE] button or turn the joystick clockwise until zoom stops at the 100X zoom limit. 2. Release the button or the joystick for one second. 3. To continue zooming (digitally), press the button or turn the joystick clockwise again until you have the picture you want or reach the digital zoom limit.

* Zoom Wide Press the [WIDE] button or turn the joystick counterclockwise.

Preset Refer to <Preset> part of this manual. Tour Refer to <Tour> part of this manual. Pattern Refer to <Pattern> part of this manual. Scan Refer to <Scan> part of this manual.

Privacy Zones Refer to the Zones section and to the documentation supplied with the control system.

*Zoom operation can be changed with respect to camera specification

-10-

Value

:0-00-00-000-00000

:XXX-XXXXX

:XXX.XXX

:NTSC or PAL

:STANDARD

: RS485/09600

: XXX

: XXX.XC/XXX.XF

: <ENT> <OPEN>

: <CLR> <CLOSE>

: ON/OFF

: ON/OFF

: ON/OFF

: ON/OFF

: ON/OFF

: ON/OFF

: <CLR> <CLOSE>

: 4digit, 0~9(UNDEFINED)

: 4digit, 0~9(UNDEFINED)

: 4digit, 0~9(UNDEFINED)

: ENABLED/DISABLED

: OFF/ON

: ON/OFF

: OFF/3SEC

: ON/OFF

: ON/OFF

: ON/OFF/3~9SEC

: 1~8(UNDEFINED)

: NULL

: NULL/0~360

: NULL/0~360

: 1~4

: Select No.

: BLOCK / DISABLED

: OFF/ON

: OFF/ON

: NTSC/PAL

: 1280x720p60, 1280x720p50,

1920x1080i60, 1920x1080i50,

1920x1080p30, 1920x1080p25

: 001~255 (Default : 1)

: 2400, 4800, 9600, 38400 (Default : 2400)

: ON/OFF

: ON/OFF

: FAST/NORMAL/LOW

: ON/OFF

S/N

MODEL

VERSION

VIDEO

PROTOCOL

COMM.

ADDRESS

TEMP.

Reboot

Exit

ALL

CAM

PRESET

TOUR

PATTERN

SCAN

(SAVE and Exit)

(EXIT without Saving)

Exit

CURRENT

NEW

CONFIRM

ENABLE

TITLE

TIME

ZOOM

ID

MODE

ANGLE

NO.

TITLE

START

STOP

GROUP

NO.

MODE

H.MIRROR

FLIP

CVBS_OUT

D_OUT

VIRTUAL ADDR.

BAUDRATE

BACKUP TASK

TURBO SPEED

PRESET SPEED

SELF TEST

INFO

　

　

　

　

　

　

　

REBOOT

　

FACTORY

　

　

　

　

　

EVENT LOG

PASSWORD

　

　

　

OSD SETUP

　

　

　

　

　

AREA TITLES

　

　

　

PRIVACY ZONE

IMAGE SETUP

RESOLUTION

GENERAL

SYSTEM

　

　

　

　

　

　

　

　

　

　

　

　

　

　

　

　

　

　

　

　

DISPLAY

　

　

　

　

　

　

　

　

　

　

　

　

　

DOME

-11-

: ON/OFF

: ON/OFF

: ON/OFF

: OFF/0~360

: ON/OFF

ON : 0~360

ON : 0~360

: HOME, PRESET, TOUR, PATTERN, SCAN

: NULL

: 1~240 min (Default : 120)

: ON(AUTO)/OFF(MANUAL)

: 1~240 (Default : 1)

: NULL

: 1~240 (Default : 5)

: 1~8 (Default : 1)

: 1~8 (Default : 1)

: NULL

: 1~8 (Default : 1)

: NULL

: 1~9 (Default : 5)

: 3~240 (Default : 5)

: AUTO/MANUAL/TRIGGER

: NORMAL/LOW

: ON/OFF

: AUTO/INDOOR/OUTDOOR/ONEPUSH/ATW/MANUAL

MANUAL MODE : R-GAIN/B-GAIN : 0~255

: FULL AUTO/MANUAL/SHUTTER PRI/IRIS PRI/BRIGHT PRI/ DSS PRI

MANUAL MODE : CLOSE/ F1.6~F14

MANUAL MODE : 1/1~1/10000

MANUAL MODE : -3dB~28dB

MANUAL MODE : CLOSE/0dB,F14~F1.6/0dB, F1.6/0dB~+28dB

: 0~15

: OFF/ON

: AUTO/DAY/NIGHT

: ON/OFF

: ON/OFF

: <ENT> <OPEN>

: <CLR> <CLOSE>

: 1~4 (UNDEFINED)

: NULL/NC/NO

: NULL/001/OFF

: NULL/1~4

: HOME/PRESET/TOUR/PATTERN/SCAN (Default : NULL)

: NULL/001

: 02~99 (Default : 5)

(Default OFF: NULL)

(Default OFF: NULL)

(Default : NULL)

(Default : NULL)

(Default : NULL)

　

　

　

(Default : NULL)

　

FULL AUTO MODE : NULL

FULL AUTO MODE : NULL

FULL AUTO MODE : NULL

FULL AUTO MODE :NULL

PROP. PAN/TILT

AUTO FLIP

OVER TILT

AZIMUTH ZERO

LIMIT STOP

-LEFT LIMIT

-RIGHT LIMIT

ACTION

NUMBER

TIME

MODE

NO.

TITLE

DWELL

NO.

NO.

TITLE

NO.

TITLE

SPEED

DWELL

FOCUS

AF.SENS

D.ZOOM

MODE

MODE

IRIS

SHUT.

GAIN

BRIGHT

SHARPNESS

BACKLIGHT

DAY&NIGHT

WDR

DSS

RESET

EXIT

NO.

IN

OUT

PRIORITY

ACTION

NUMBER

DWELL

MOTION

　

　

　

　

　

　

HOME

　

　

　

PRESET

　

　

TOUR

PATTERN

　

SCAN

　

　

　

FOCUS/ZOOM

　

　

W-BALANCE

EXPOSURE

　

　

　

ADVANCED

　

　

　

SYSTEM

CAMERA

　

　

　

　

　

　

　

　

　

　

　

　

　

ALARM

　

　

　

　

　

　

EXIT

-12-

█

The system Information displays serial number/model name/Running Version/Protocol/Communication Type/Address switch No./Temperature.

System settings cannot be edited in this menu. This screen is for reference only.

Use the following steps to display the system in formation screen:

1. Press the MENU key(refer to ‘Accessing main menu’)2. Use the joystick to position the cursor beside SYSTEM.3. Move the joystick right.4. Select INFO using joystick.

Note-Version can be changed as system evolves.-Address changes with respect to ‘address switching setting-Temperature can be changed as environment change

<< SYSTEM INFORMATION >>██████████████████████████S/N:0-00-00-000-00000MODEL : XXX-XXXXVERSION : XXX-XXXXVIDEO : NTSC.PALPROTOCOL : STANDARDCOMM. : RS485/02400ADDRESS : 001TEMP. : 044.0C/111.2F██████████████████████████■ Exit: <CLR> <CLOSE>

-13-

Reboot the system if it is not operating or if there is no control. The system will cycle power without changing programmed dome settings.

Use the following steps to display the system information screen:1. Press the Menu Key(refer to ‘Accessing main menu’)2. Select SYSTEM using the joystick.3. Select REBOOT using the joystick in the sub menu of SYSTEM.4. To Reboot the system, Press [ENT] or [OPEN]. To cancel Reboot, Press [CLR] or [CLOSE] key.

SYSTEM: REBOOT

■ Reboot: <ENT> <OPEN>■ Exit: <CLR> <CLOSE>

██████████████████████████►SYSTEM > INFODISPLAY > ►REBOOTDOME > FACTORYCAMERA > EVENT LOGALARM PASSWORD EXIT

██████████████████████████►SYSTEM > DISPLAY > DOME >CAMERA > ALARM EXIT

<<<<< Main MENU >>>>>

<<<<< Main MENU >>>>>

-14-

Use this function to reset all camera settings to factory default parameters.You can reset a specific setting to factory default parameters.

Use the following steps to display the System Information screen:1. Press the MENU key (refer to ‘Accessing main menu’)2. Select SYSTEM using the joystick.3. Select FACTORY in the sub menu of SYSTEM using the joystick.4. Select items to be reset.5. Press [ENT] button or move the cursor to <SAVE and exit> and then move the joystick right.

ALL : Restores all save items (CAM/PRESET/TOUR/PATTERN/SCAN)CAM : Reset Camera related settings.PRESET : Reset Saved presets. (To reset specific preset, refer to Preset part of this manual)TOUR : Reset Saved Tours.PATTERN : Reset Saved pattern.SCAN : Reset Saved Scan items.

SYSTEM: FACTORY

██████████████████████████►SYSTEM > INFO DISPLAY > REBOOTDOME > ►FACTORY CAMERA EVENT LOG ALARM PASSWORDEXIT

██████████████████████████►SYSTEM >DISPLAY >DOME >CAMERA >ALARM EXIT

<<<<< Main MENU >>>>>

<<<<< Main MENU >>>>>

<< FACTORY SETUP >>██████████████████████████►ALL : OFF CAM : OFF PRESET : OFF TOUR : OFF PATTERN : OFF SCAN : OFF██████████████████████████ <Save and Exit> <Exit without Saving>

-15-

Event Log shows the current dome status and dome event logs.If the dome finds some problems, it displays error signal and savethe log to EEPROM. Turn SELF TEST on to monitor the dome’sstatus and save all event logs. See <DOME : GENERAL> forSELF TEST descriptions.

Use the following steps to display the EVENT LOG screens:1. Press the MENU key (refer to ‘Accessing main menu’)2. Select system using the joystick.3. Select EVENT LOG in the sub menu of SYSTEM using the joystick.4. <Code> means the type of error. <CNT> means the number of error occurred during camera operation. When you scroll up and down using the joystick, you can find what kind of errors has occurred during operation.

5. Press the [CLR] or [CLOSE] key to return previous menu.

SYSTEM: EVENT LOG

<<<<< Main Menu >>>>>██████████████████████████►SYSTEM > DISPLAY > DOME > CAMERA > ALARM EXIT

<<<<< Main Menu >>>>>██████████████████████████►SYSTEM > INFO. DISPLAY > REBOOT DOME > FACTORY CAMERA > ►EVENT LOG ALARM PASSWORD EXIT

<<<< EVENT LOG >>>>██████████████████████████Code:0000,Cnt:00,Drp:000Current Status-----------------------

██████████████████████████Exit: <CLR> <CLOSE>

<<<< EVENT LOG >>>>██████████████████████████Code:0000,Cnt:00,Drp:000None............-----------------------►01.00 Empty........... 02.00 Empty........... 03.00 Empty........... 04.00 Empty........... 05.00 Empty...........██████████████████████████Exit: <CLR> <CLOSE>

-16-

The dome features password protection to prevent unauthorizedchanges to the dome settings. An operator cannot access any ofthe Dome Settings menus.

Controller/ keyboard commands cannot override password-protected settings. If a keyboard accesses to set a preset, pattern or zone, the screenfor entering Password appears on the monitor.

The password must be entered before programming to continue.Four characters must be entered to create a valid password.

Use the following steps to set up password :1. Press the MENU key (refer to ‘Accessing main menu’)2. Select SYSTEM using the joystick.3. Select PASSWORD in the sub menu of SYSTEM using the joystick.4. Select number using the joystick left/right and press the TELE key or twist Joystick. Clockwise to input. Repeat this action to fill current/new/confirm password.5. To enable password set ENABLE:ENABLED

Note-The default password is “0000”-When you initialize the system with <SYSTEM:FACTORY>, password will be removed.

SYSTEM: PASSWORD

<<<<< Main Menu >>>>>██████████████████████████►SYSTEM > DISPLAY > DOME > CAMERA > ALARM EXIT

<<<<< Main Menu >>>>>██████████████████████████►SYSTEM > INFO. DISPLAY > REBOOT DOME > FACTORY CAMERA > EVENT LOG ALARM ►PASSWORD EXIT

PASSWORD██████████████████████████ ►CURRENT: x--- NEW : ---- CONFIRM: ---- ENABLE : DISABLED██████████████████████████ x12456789

-17-

OSD setup allows you to program how labels are displayed on the monitor.

The following labels are available :TITLE Identifies area and operation titles.TIME Identifies dwell time.ZOOM Identifies the amount of magnification.ID Identifies dome address.MODE Identifies dome operation mode.ANGLE Amount of pan/tilt from 0° .

The zoom ratio label is displayed when zoom is activated.The following settings are available for each label :OFF Label is not displayed when activated.ON The label is continually displayed.xx SEC The label is displayed for xx seconds after activation.

Labels can be placed anywhere on the monitor. This feature allows you to customize the appearance of your monitor screen.

To set a label position :1. Press the MENU key(refer to ‘Accessing main menu’)2. Select DISPLAY and select OSD SETUP using the joystick.3. Press the [TELE] button or turn the joystick clockwise.4. Use the joystick to move the label up, down, left and /or right.5. Press [ENT] or [OPEN] key.6. Repeat steps 1 through 4 to position other labels.7. Select <Save and Exit> to save settings and exit menu.8. Select <Exit without Saving> to exit menu without saving settings.

Note-Press [ENT] or [OPEN] key to save settings and exit to previous menu. Press [CLR] or [CLOSE] key to go to previous menu without saving any settings at any time.

DISPALY: OSD SETUP

██████████████████████████SYSTEM > ►DISPLAY > ►OSD SETUP DOME > AREA TITLES CAMERA > PRIVACY ZONE ALARM IMAGE SETUP EXIT RESOLUTION

██████████████████████████SYSTEM >►DISPLAY > DOME > CAMERA > ALARM EXIT

████████████ •••••• ████████████

••••••••• •••••••

•••••••••

<<<<< Main MENU >>>>>

<<<<< Main MENU >>>>>

<< OSD SETUP >>██████████████████████████►TITLE : OFF TIME : OFF ZOOM : 3 SEC ID : ON MODE : ON ANGLE : 3 SEC██████████████████████████ * To Setup: <TELE> * Change: <LEFT/RIGHT>

Twist joystick clockwiseor press [TELE] button

-18-

A zone is a pan area, defined by a left and right limit on the pan plane.The dome system is capable of 8 area titles, each with a 12 character label.

To program a zone :1. Press the MENU key (refer to ‘Accessing main menu’)2. Select DISPLAY and select AREA TITLE using the joystick.3. Use the joystick to position the cursor beside NO.xxx. Move left or right to select zone ID. Press the [TELE] button or turn the joystick clockwise to setup START and stop pan limit angel.4. Move the joystick to position start limit angle Press [ENT] or [OPEN] to save START limit angle.5. Move the joystick to position stop limit angel, Press [ENT] or [OPEN] to save STOP limit angle.6. Edit a title, See [TITLE EDIT] section for detail.

To clear an area title:1. Press the MENU key (refer to ‘Accessing main menu’)2. Select DISPLAY and select AREA TITLE using the joystick.3. Use the joystick to position the cursor beside NO.xxx. move left or Right to select zone ID.4. Press the [WIDE]or turn the joystick counterclockwise to clear area title.

Note-after saving area titles, turn on the TITLE menu in the <DISPLAY:OSD SETUP> to view the area title.

Note-Press [ENT] or [OPEN] key to save settings and exit to previous menu. Press [CLR] or [CLOSE] key to go to previous menu without saving any settings at any time.

DISPALY: AREA TITLES

█ Start Position Setup

█ Press MOVE Key█ Save: <ENT> <OPEN>█ Exit: <CLR> <CLOSE>

██████████████████████████SYSTEM > ►DISPLAY > OSD SETUPDOME > ►AREA TITLESCAMERA > PRIVACY ZONEALARM IMAGE SETUP EXIT RESOLUTION

<< AREA TITLE SETUP >>██████████████████████████►NO.001 : █• • • • • • • TITLE : -START : -STOP : ██████████████████████████ <Save and Exit> <Exit without Saving>

<<<<< Main MENU >>>>>

Twist joystick clockwiseor press [TELE] button

-19-

█ Press MOVE Key█ Save: <ENT> <OPEN>█ Exit: <CLR> <CLOSE>

██████████████████████████SYSTEM > ►DISPLAY > OSD SETUPDOME >

►AREA TITLES

CAMERA > PRIVACY ZONEALARM IMAGE SETUP EXIT RESOLUTION

<<<<< Main MENU >>>>>

Twist joystick clockwiseor press [TELE] button

-20-

DISPLAY: PRIVACY ZONE

A privacy zone allows a user to program one four-sided, user-defined area that cannot be viewed by the operator of the dome system. The blanked area will move with pan and tilt functions and automatically adjust in size as the lens zooms telephoto and wide.

1.Group no : Identifies group ID. Can have 1~82. No. xxx : Identifies privacy zone ID. Can have 1~43. Mode : DSABLE - disable privacy zone BLOCK - Enable privacy zone4. Privacy Mask : adjust mask size 3-1 : PAN/TILT - adjust position 3-2 : TELE - enlarge mask size 3-3 : WIDE - make mask size small

To program a privacy zone:

1. Press the MENU key2. Select DISPLAY and select PRIVACY ZONE using joystick.3. Use the joystick to position the cursor beside NO.xxx. Move left or right to select zone ID. Press the [TELE] button or turn the joystick clockwise to setup a zone.4. Follow the instructions that appear on the screen.5. The Privacy Zone menu reappears with a saved marked (█) option.

To disable or clear a Privacy Zone (a zone is enabled automatically when it is programmed):

1. Use the joystick to position the cursor beside NO.xxx.Move left or right to select zone ID.2. Press the [WIDE] button or turn the joystick counterclockwise to clear.

Note - Press [ENT] or [IRIS OPEN] key to save settings and exit to previous menu or Press [Esc] or [IRIS CLOSE] key to go to previous menu without saving any settings at any time.Note- When camera is pointed vertically, the Privacy zone can’t be set around 40° area in this situation.

<< PRIVACY ZONE SETUP >>██████████████████████████ GROUP : 1►NO.001 : █• • • MODE : DISABLE██████████████████████████ <Save and Exit> <Exit without Saving>

This menu allows operator to change of displayed image settings.

The following four options are available:

H.MIRROR left-right reversal imageFLIP upside-down image

To set up image display

1. Press the MENU key (refer to ‘Accessing main menu’)2. Select DISPLAY and select IMAGE SETUP using the joystick.3. Select one of jour possible settings.

Note-Press [ENT] or [OPEN] key to save settings and exit to previous menu.- Press [CLR] or [CLOSE] key to go to previous menu without saving any settings at any time.

DISPALY: RESOLUTION

This menu is to select the resolution.

To set the resolution :1. Press the MENU key (refer to ‘Accessing main menu’)2. Select DISPLAY and select RESOLUTION using the joystick.3. Select NTSC or PAL on the CVBS-OUT.4. Select the right resolution on the D-OUT.

Note-Press [ENT] or [OPEN] key to save settings and exit to previous menu. Press [ESC] or [CLOSE] key to go to previous menu without saving any settings at any time.

DISPALY: IMAGE SETUP

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > ►DISPLAY > OSD SETUP DOME > AREA TITLES CAMERA > PRIVACY ZONE ALARM ►IMAGE SETUP EXIT RESOLUTION

<< IMAGE SETUP >>██████████████████████████►H.MIRROR : OFF FLIP : OFF██████████████████████████ <Save and Exit> <Exit without Saving>*Left Right Reversal*Upside-Down

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > ►DISPLAY > OSD SETUP DOME > AREA TITLES CAMERA > PRIVACY ZONE ALARM IMAGE SETUP EXIT ►RESOLUTION

<< RESOLUTION SETUP >>██████████████████████████►CVBS-OUT : NTSC D-OUT : 1920x1080p30 -720p60 -720p50 -1080i60 -1080i50 -1080p30 -1080p25██████████████████████████ <Save and Exit> <Exit without Saving>

-21-

This menu controls general dome related functions.Detail description is as follow.

VIRTUAL ADDRESSDome ID is generally assigned with address switch.but using this menu you can assign the dome ID with S/W.so after power on/off, reboot, the ID is assigned with address switch.Dome General Virtual Address Controller Joystick Left or Right Direction.Virtual Address Save (1~255 Address)

BAUDRATEYou can select the transmission speed on this menu.

BACKUP TASKThis setting defines a specific (preset, tour, pattern and scan) activityTo be performed in the event the power to the dome is cycled or after alarm action.The following settings are available:OFF No action.ON (default) The dome resumes its prior activity.

TURBO SPEEDThis setting defines the manual pan and tilt speed.The following settings are available:OFF (default) Max speed is 90 degrees per second.ON Max speed is 180 degrees per second.

NoteTurbo speed is only applicable to manual operation not for preset, tour, pattern etc.

PRESET SPEEDYou can optimize preset speed with this menu.There are three options:FAST NORMAL SLOW

SELF TESTThis setting defines the diagnostic monitoring activity.When the dome finds some problems, the error signal is displayed.For details, see <SYSTEM : EVENT LOG> section in this manual.The following settings are available:OFF(default) Disable self-testON Enable self-test

DOME: GENERAL SETUP

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > ►GENERAL►DOME > MOTION CAMERA > HOME ALARM PRESET EXIT TOUR PATTERN SCAN

<< GENERAL SETUP >>██████████████████████████ VIRTUAL ADDR : 001►BAUDRATE : 9600bps BACKUP TASK : ON TURBO SPEED : OFF PRESET SPEED : FAST SELF TEST : OFF██████████████████████████ <Save and Exit> <Exit without Saving>

-22-

PROPORTIONAL PAN/TILTProportional pan/tilt automatically reduces or increases the pan and tilt speeds in proportion to the amount of zoom. At telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of the joystick deflection tan at wide zoom settings.There are two proportional pan/tilt modes:ON (default) Enables the proportional pan/tilt mode.OFF Disables proportional pan/tilt mode. The pan/tilt speed will not depend on the amount of zoom.

AUTO FLIPWhen the camera tilts downward and goes just beyond the vertical position, the dome rotates 180 degrees. When the dome rotates (flips), the camera starts moving upward as long as you continue to hold the joystick in the down position. Once you let go of the joystick after the dome rotates, joystick control returns to normal operation.ON (default) Auto flip mode is enabled.OFF Auto flip mode is disabled.

OVER TILTTo prevent horizontal view cut with trim ring or ceiling, this menu restrict horizontal view angel.ON restrict minimum tilt angle to -1.8 degreeOFF restrict minimum tilt angle to 4.5 degree.

AZIMUTH ZEROAzimuth zero is the pan angle from 0° to 359°. Azimuth zero is the pan position you specify to be the 0° point. Azimuth zero is normally set to magnetic north. Once set, azimuth is based on the set Azimuth zero point.

To set Azimuth zero :1. Use the joystick to position the cursor beside AZIMUTH ZERO.2. Press [TELE] or twist the joystick clockwise.3. Follow the directions displayed on the monitor.

To clear Azimuth zero :1. Use the joystick to position the cursor beside AZIMUTH ZERO.2. Press [WIDE] or twist the joystick counterclockwise.

DOME: MOTION

<< MOTION SETUP >>██████████████████████████ PROP. PAN/TILT: ON AUTO FLIP : ON OVER TILT : ON AZIMUTH ZERO : OFF►LIMIT STOP : OFF -LEFT LIMIT : -RIGHT LIMIT :██████████████████████████ <Save and Exit> <Exit without Saving>

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > GENERAL►DOME > ►MOTION CAMERA > HOME ALARM PRESET EXIT TOUR PATTERN SCAN

<< MOTION SETUP >>██████████████████████████►PROP. PAN/TILT: ON AUTO FLIP : ON OVER TILT : ON AZIMUTH ZERO : OFF LIMIT STOP : OFF -LEFT LIMIT : -RIGHT LIMIT :██████████████████████████ <Save and Exit> <Exit without Saving>

-23-

DOME: MOTION

DOME: HOME

-24-

LIMIT STOPLimit stops are programmable stops that limit the pan range of the dome.There must be two limits, a left and a right, to define an area, A manual(joystick) pan operation stops when a limit stop is reached.To set limit stops :1. Use the joystick to position the cursor beside LIMIT STOP.2. Press [TELE] or twist the joystick clock wise.3. Follow the directions displayed on the monitor.To clear limit stops, set limit stop mode to OFF.1. Use the joystick to position the cursor beside LIMIT STOP.2. Press [WIDE] or twist the joystick counterclockwise.

This feature defines the activity which is set should be executed after assigned idle time.

ACTION / NUMBER

PRESET [NUMBER] Dome goes to preset [NUMBER].TOUR [NUMBER] Runs tour [NUMBER].PATTERN [NUMBER] Dome starts pattern [NUMBER].SCAN [NUMBER] Dome goes to scan [NUMBER].

Note-In order to call action preset, tour, pattern or scan, you must save preset, tour, pattern or scan first.

TIMEThis feature allows the dome to begin a user specific action after a programmed time of inactivity. Home time can be programmed from 1 minute to 240 minutes (4 hours).

MODEON(AUTO) (default) Enabled HOME function.OFF(MANUAL) Disables this feature.

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > GENERAL►DOME > MOTION CAMERA > ►HOME ALARM PRESET EXIT TOUR PATTERN SCAN

<< HOME SETUP >>██████████████████████████►ACTION : HOME NUMBER : TIME : 120 min MODE : ON██████████████████████████ <Save and Exit> <Exit without Saving>

The dome system can have maximum 240 preset positions.

Use the following steps to program a preset.

1. Press the MENU key (refer to ‘Accessing main menu’).2. Select DOME and select PRESET using joystick.3. Select the preset number. a. Use the joystick to position the cursor beside NO.xxx. Move Left or right to select preset ID. b. Press the [TELE] button or turn the joystick clockwise to setupAngle. Follow the directions displayed on the monitor to edit the preset scene.4. Edit the preset label. Refer to TITLE:EDIT section on this manual.5. Edit the dwell time.6. Save the settings.

To disable or clear a PRESET :

1. Use the joystick to position the cursor beside NO.xxx. Move left or right to select preset ID.2. Press the [WIDE] key or turn the joystick counterclockwise to clear.

Note-Press [ENT] or [OPEN] key to save settings and exit to previous menu or Press [Esc] or [CLOSE] key to exit to previous menu without saving any settings at any time.

DOME: PRESET

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > GENERAL►DOME > MOTION CAMERA > HOME ALARM ►PRESET EXIT TOUR PATTERN SCAN

<< PRESET SETUP >>██████████████████████████►NO.001 : Saved TITLE : DWELL : -PTZ : ██████████████████████████ <Save and Exit> <Exit without Saving>Press <TELE> To SetupPress <WIDE> To Clear

* Start Position Setup

* Press MOVE Key* Save: <ENT> <OPEN>* Exit: <CLR> <CLOSE>

-25-

The dome system has 8 guard tours. Each of the tour has 30 items.Each item can have pre-defined preset, pattern, scan and any other tour.

To program a tour.

1. Press the MENU key (refer to ‘Accessing main menu’). 2. Select DOME and select TOUR using the joystick.3. Use the joystick to position the cursor beside NO.xxx. Move left or right to select tour ID. Press the [TELE]button or turn the joystick clockwise to setup.4. To insert items, Use following steps : a. To save the preset. - Move the joystick to position the cursor beside XXX. - Press the [TELE] button or twist the joystick clockwise to select the preset number. b. To save the Scan or Pattern, - Move the joystick to position the cursor beside XXX. - Please press the [NEAR] or [FAR button] on the keyboard. You can select Scan or Pattern.5. Follow the directions displayed on the monitor.6. Before select a specific item, save it first.

To disable or clear a tour.

1. Use the joystick to position the cursor beside NO.xxx. Move left or right to select tour ID.2. Press the [WIDE] button or turn the joystick counterclockwise to clear.

DOME: TOUR

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > GENERAL►DOME > MOTION CAMERA > HOME ALARM PRESET EXIT ►TOUR PATTERN SCAN

<< TOUR SETUP >>██████████████████████████►NO.001 : Saved=== === === === === ====== === === === === ====== === === === === ====== === === === === ====== === === === === ===██████████████████████████* Change ID:<TELE/WIDE>* Change Action:<NEAR>

-26-

A pattern is a memorized, repeating, series of pan, tilt, zoom and preset functions that can be called with a command from a controller or automatically by a programmed function.The dome system can have maximum 8 user-defined patterns.

To program a Pattern :

1. Press the MENU key (refer to ‘Accessing main menu’).2. Select DOME and select PATTERN using the joystick.3. Use the joystick to position the cursor NO.xxx. Move left or right to select pattern ID.4. Press the [TELE] button or turn the joystick clockwise to start to learn.5. Follow the directions displayed on the monitor.6. To finish learning, press [ENT] or [CLOSE] key. To cancel learning, press [CLR] or [CLOSE] key.7. Edit title. Refer to [TITLE DEIT] section in this manual.

To clear a pattern :

1. Use the joystick to position the cursor beside NO.xxx. Move the Joystick left or right to select a pattern ID.2. Press the [WIDE] key or turn the joystick counterclockwise

DOME: PATTERN

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > GENERAL►DOME > MOTION CAMERA > HOME ALARM PRESET EXIT TOUR ►PATTERN SCAN

<< PATTERN SETUP >>██████████████████████████►NO.001 : █• • • • • • • TITLE : -TIME : ██████████████████████████ <Save and Exit> <Exit without Saving>Press<TELE> To LearnPress<WIDE> To Clear

-27-

Scan is a pan and tilt functions from one point to another point.The dome has 8 user-defined auto scans.

To program a scan :1. Press the MENU key (refer to ‘Accessing main menu’). 2. Select DOME and select PATTERN using the joystick.3. Use the joystick to position the cursor beside NO.xxx. Move left or right to select a scan number.4. Press the [TELE] key or turn the joystick clockwise to start to Setup start and stop position.5. Edit a title. Refer to [TITLE EDIT] section in this manual.6. Select scan speed. Scan speed is the degree per second that the dome will pan when it is in a scan mode. The range of scan speed is from 1 to 9 the default value is 5.

*When the start and stop position are same, scan mode is changed to ENDLESS automatically. Any other case, the mode is COMING & GOING

To clear a scan :1. Use the joystick to positions the cursor beside NO.xxx. Move the joystick left or right to select a scan number.2. Press the [WIDE] key or turn the joystick counterclockwise. How to activate a scan Press the specific number key and then press [SCAN]. Ex) [1]+[SCAN]

You can also access this menu with [SCAN] key.

Note-Press [ENT] OR [OPEN] key to save settings and exit to previous menu or Press [CLR] or [CLOSE] key to go to pervious menu without saving any settings at any time.

DOME: SCAN

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > GENERAL►DOME > MOTION CAMERA > HOME ALARM PRESET EXIT TOUR PATTERN ►SCAN

<< SCAN SETUP >>██████████████████████████►NO.001 :█• • • • • • • TITLE : SPEED :5 DWELL :005 sec. -MODE :COMING & GOING -START : -STOP :██████████████████████████*Press <TELE> To Learn*Press <WIDE> To Clear

* Start Position Setup

* Press MOVE Key* Save: <ENT> <OPEN>* Exit: <CLR> <CLOSE>

-28-

FOCUS

There are three auto focus settings :AUTO If auto focus mode is set to NO. the camera will focus automatically.MANUAL Focus is operated manually. To focus, press [NEAR] or [FAR] key on the controller. TRIGGER (default) If auto focus mode is set to TRIGGER, the camera will focus when zoom operates.

Note Auto focus will malfunction at below condition. -very dark or shiny area -when slow shutter is activated -area which doesn’t have contrast difference

AF.SENS(Auto Focus Sensitivity)

NORMAL(Default) : Make the focus speed fast. LOW : When the speed of target is slow or the AF function is not affected.

D.ZOOM(Digital Zoom)

ON(Default) : Enable Digital zoom.OFF : Disable Digital zoom.

Note- Press [ENT] or [OPEN] key to save settings and exit to previous menu. Press [CLR] or [CLOSE] key to go to previous menu without saving any settings at any time.

CAMERA: FOCUS / ZOOM

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > DOME > ►FOCUS/ZOOM►CAMERA > W-BALANCE ALARM EXPOSURE EXIT ADVANCED SYSTEM

<< FOCUS/ZOOM SETUP >>██████████████████████████►FOCUS : TRIGGER AF.SENS : NOMAL D.ZOOM : ON██████████████████████████ <Save and Exit> <Exit without Saving>

-29-

This feature automatically processes the viewed image to retain color balance over temperature range.

White Balance has following modes.

AUTOAutomatic White Balance.

ATWAutomatic White Balance in any lighting condition.

INDOORAutomatic White Balance for indoor.

OUTDOORAutomatic White Balance for outdoor.

ONEPUSHShow the present status.

MANUALManual White Balance. As you change the R or B gain value.You will see the color change on your monitor.R GAIN Adjust the picture output in the red range. (Range : 0~255)B GAIN Adjust the picture output in the blue range. (Range : 0~255)

Note: Auto white balance will malfunction at below condition. - Very dark or shiny area (clear sky, sunset) - Direct shot of fluorescent lamp or much difference brightness area

Note- Press [ENT] or [OPEN] key to save settings and exit to previous menu or Press [CLR] or [CLOSE] key to exit to previous menu without saving any settings at any time.

CAMERA: WHITE BLANCE

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > DOME > FOCUS/ZOOM►CAMERA > ►W-BALANCE ALARM EXPOSURE EXIT ADVANCED SYSTEM

<< WB SETUP >>██████████████████████████►MODE : AUTO R GAIN : B GAIN : ██████████████████████████ <Save and Exit> <Exit without Saving>

-30-

Exposure has following modes

FULL AUTO Function that automatically opens and closes the iris, adjusts GAIN in response to changing light conditions.

MANUAL Function that keeps the setting of Shutter speed, IRIS, GAIN regardless of light condition

SHUTTER PRI Shutter speed is set as priority.IRIS will be changed in response to the value of Shutter speed.

IRIS PRIIRIS value is set as priority.Shutter speed will be changed in response to the IRIS value.

BRIGHT PRIBRIGHT is set as priority.

CAMERA: EXPOSURE

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > DOME > FOCUS/ZOOM►CAMERA > W-BALANCE ALARM ►EXPOSURE EXIT ADVANCED SYSTEM

<< AE SETUP >>██████████████████████████►MODE : FULL AUTO IRIS : SHUTTER : GAIN : BRIGHT : ██████████████████████████ <Save and Exit> <Exit without Saving>

<< AE SETUP >>██████████████████████████►MODE : MANUAL IRIS : 068 SHUTTER : x4 AGC : MID BRIGHT : LOW DSS : x4██████████████████████████ <Save and Exit> <Exit without Saving>

-31-

SHARPNESSSettings ranges from 0 to 15. Sharpness enhances picture detail by increasingThe aperture gain of the camera and sharpening the edges in the picture.

BACKLIGHT(BLC-Backlight compensation)Backlight compensation enhances objects in the center of the picture.The dome uses the center of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to white. The camera will adjust the iris so that the object in the sensitive area is property exposed.

OFF(default) Backlight compensation is not activated. ON : LOW/MIDDLE/HIGH Backlight compensation is activated.

DAY & NIGHTAUTO/DAY/NIGHT According to the luminance level, Day & Night filter is automatically switched.

This function is for reset of camera due to malfunction.

CAMERA: ADVANCED SETUP

CAMERA: SYSTEM

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > DOME > FOCUS/ZOOM►CAMERA > W-BALANCE ALARM EXPOSURE EXIT ►ADVANCED SYSTEM

<< ADVANCED SETUP >>██████████████████████████►SHARPNESS : 07 BACKLIGHT : OFF DAY&NIGHT : AUTO WDR : OFF DSS : OFF██████████████████████████ <Save and Exit> <Exit without Saving>

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > DOME > FOCUS/ZOOM►CAMERA > W-BALANCE ALARM EXPOSURE EXIT ADVANCED ►SYSTEM

*Reset : <ENT><OPEN>*Exit : <CLR><CLOSE>

-32-

IN (3ea of ALARM INPUT )NO Normal Open.NC Normal Close.OUT (1ea of ALARM OUTPUT)

1. Go to “No.001”-> turn the joystick with clockwise. If you cancel, please turn the joystick with counter-clock wise

2. Go to “In” -> Please set the NO or NC

3. Go to “out” -> Please set the “001” or off - “001” means input “ON” - OFF(default): No action.

4. PRIORITY You can set the priority order for Alarm 1.2.3.4

5. ACTION In case of alarm event, go to the preset or pattern or scan, tour.

6. Number Number means the number of preset or pattern or scan, tour which is already set the each menu.

7. Dwell Dwell means how long is ring the sound, also how long take a action event.

8. To save. Press [ENT] or [OPEN] key to save settings and exit to previous menu or Press [CLR] or [CLOSE] key to exit to previous menu without saving any settings at any time.

9. To disable an alarm If you want cancel the alarm event, please move the joystick and then go to the “No. xxx” (Alarm number). Press the <WIDE> button or turn the joystick counterclockwise. If the joystick is moved, the alarm setting will be stopped for 10 sec.

ALARM

<< ALARM SETUP >>██████████████████████████►NO.001 : █• • • IN : OUT : PRIORITY : ACTION : NUMBER : DWELL : ██████████████████████████ <Save and Exit> <Exit without Saving>

<<<<< Main Menu >>>>>██████████████████████████ SYSTEM > DISPLAY > DOME > CAMERA > ►ALARM EXIT

-33-

-34-

1/2.8" 2.0M Progressive CMOS Image Sensor

F1.6 ~ F3.5, f=4.7mm ~ 94.0mm

20x Optical Zoom (12x Digital Zoom)

10mm(Wide) ~ 1000 mm(Tele)

Horizontal: 55.4°(Wide) ~ 2.9°(Tele)

0.08 Lux (1/4 sec, 50 IRE, High Sensitivity Mode ON)

50 dB

Auto/ Manual/ Shutter Priority/ Iris Priority / Bright Priority

-3dB ~ +28dB(16 Levels)

1/1 sec to 1/10000 (22 Levels)

AUTO/ ATW/ INDOOR/ OUTDOOR/ ONE PUSH/ MANUAL

On/ Off

Auto/ Color/ B&W

On/ Off

On/ Off/ Auto

HD-SDI(BNC Type) and CVBS(BNC Type)

30fps@1920 x 1080 ~ 30fps@1280 x 720

Pan:360°(Endless)/ Tilt: -2°~182°

Manual: 0.1° ~ 360°/sec(Zoom Proportional)

240 Preset Positions (Depending on Protocol)

Title, Time Setting

8 Patterns(Approx. 2 Minutes for each Pattern)

8 Scans

8 Groups(Max 30 Entries for each Group)

RS-485/RS-422 for PTZ Control

Bandi(STD), Pelco-D, Pelco-P, Honeywell (Option), AD (Option), Dyna Color (Option)

Motion Detection

4 Alarm Inputs

1-Relay Out(N.O)

233(W) x 235(H)mm

CE, FCC, RoHS, KC, IP67

Approx. 2200g

DC12V 3A, AC24V

IP67

Always Operation

4℃(39.2°F) ~ 10℃(50°F) Operation, 30W

-50℃ ~ 60℃(-58℉ ~ 140℉)

Image Sensor

Focal Length

Zoom

Focus Position

Angle of View

Minimum Illumination

S/N Ratio

AE Mode

Gain Control

Shutter Control

White Balance

Digital Noise Reduction

Day & Night

Backlight Compensation

Wide Dynamic Range

Video Output

Resolution

Pan/Tilt Angle

Pan Speed

Preset Position

Pattern

Scan

Group

Port

Protocol

Event Input

Alarm Input

Alarm Output

Dimension

Certifications

Weight

Power Source

Waterproof

Fan

Heater

Operation Temperature

Signal Format

Camera

Video

Pan/Tilt

RemoteControl

Alarm / Event

Physical

* It can be changedable without notice due to product feature.