Upload
kotakamals
View
25
Download
0
Tags:
Embed Size (px)
DESCRIPTION
OBD interface
Citation preview
Outils OBD Facile – January 2015 All rights reserved
INSTRUCTION MANUAL
BY
Outils OBD Facile – January 2015 Tous droits réservés
CONTENTS
1 Installation _______________________________________________________________________________ 1 2 How to activate your software? ______________________________________________________________ 1 3 Overview ________________________________________________________________________________ 2 4 Connecting to the vehicle (USB and RS232) ____________________________________________________ 3 5 Connecting using a Bluetooth interface ________________________________________________________ 3 6 Connecting using a WiFi interface____________________________________________________________ 4 7 Configuring a new vehicle __________________________________________________________________ 5 8 Configuring the software ___________________________________________________________________ 5 9 The “Diagnostic” tab _______________________________________________________________________ 6 10 The “Advanced Diagnostic” tab ______________________________________________________________ 7 11 “Sensors” tab _____________________________________________________________________________ 8 12 The “Oxygen sensors” tab __________________________________________________________________ 9 13 “Monitored system results” tab _____________________________________________________________ 10 14 “Vehicle Info” tab ________________________________________________________________________ 11 15 “Terminal” tab __________________________________________________________________________ 12 16 The “Graph and recording” window _________________________________________________________ 13
16.1 Display values _______________________________________________________________________ 13 16.2 Display/record options ________________________________________________________________ 13 16.3 Replay a recording ___________________________________________________________________ 14 16.4 Smart triggers _______________________________________________________________________ 15 16.5 Exporting recording to a spreadsheet ____________________________________________________ 15
17 The “Dashboard” window _________________________________________________________________ 16 18 The “CAN bus analyser” window ___________________________________________________________ 17
18.1 Display frames ______________________________________________________________________ 17 18.2 Filtering the CAN bus_________________________________________________________________ 17
19 PID Decoder _____________________________________________________________________________ 18 20 Customisation ___________________________________________________________________________ 18
20.1 How to add specific manufacturer codes __________________________________________________ 18 21 Error messages: __________________________________________________________________________ 18
21.1 Errors from the ELM interface _________________________________________________________ 18 22 Frequent problems, tips ___________________________________________________________________ 19
22.1 Connection problems with the vehicle ____________________________________________________ 19 22.2 Asynchronous socket error _____________________________________________________________ 19 22.3 Fault deletion problem ________________________________________________________________ 19 22.4 Renault "hands-free" kit ______________________________________________________________ 19 22.5 Repair tutorials ______________________________________________________________________ 19 22.6 Contacts ____________________________________________________________________________ 19
EOBD-Facile Manual
Outils OBD Facile – January 2015 1
1 Installation Important: In order to use the software, you must first install the
interface driver. If you are using a USB interface, download the driver the installation procedure from our website in the download section: http://www.outilsobdfacile.fr/telechargement-logiciel-elm327.html
Installation: Download the latest version of EOBD-Facile from our website and run the installer called Install EOBD-Facile.exe.
The software requires no special installation and will not modify
your registry. It is important to note that the software does not use:
Registry key Hidden files Does not create any files or directories outside its
installation directories Does not modify your Windows parameters (resolution,
settings…)
Update: After downloading the new version, re-install the
software in the directory already containing it. All the old files will be replaced with the new ones. Above all, do not delete the EOBD-Facile directory in “My Documents” containing your settings and your saved data.
Uninstallation: If you wish to uninstall the software, just delete
the files and directories in the directory containing the application. Your personal connection and data files are in the directory “My
documents\EOBD-Facile”. You may delete them if you will no longer need them.
2 How to activate your software? Procedure:
1. Connect to your vehicle and use the wizard present in the menu "Register" and "Create a registration file".
2. Follow the instructions to create a file to be returned to us by email
3. You will receive a reply with a login and activation key (within 24 hours maximum)
4. Enter this information in the software via the menu "Register" then "register..."
5. Restart the software
Why should you register?
Registration will activate additional functions in the software. The log file that you will provide to register will enable future users to benefit from your experience and create a list of EOBD compatible vehicles and the functions that they support.
Registration is free of charge and only requires a few minutes.
Can I install EOBD-Facile on another PC using my registration data?
Unfortunately not, the registration data you receive is only valid for the PC used to generate the log file. If you have already registered and need a second key for another PC, please send us an email with your login and include a log file generated with this new PC (this file can be generated without connecting to a vehicle using the “Demonstration” mode and creating a file log-demo.txt, to attach to your email). Similarly, if you have lost your registration data following reformatting or deletion of EOBD-Facile, send us an email requesting them.
EOBD-Facile Manual
Outils OBD Facile – January 2015 2
3 Overview The software is comprised of several principal zones described
below Menus: contain the various main menus for the software:
File containing the menu Parameters and PID Decoder.
Language to choose the language used by the software Interface to view the interface parameters Calculators to select the calculator on which to run the
diagnostics. Additional functions containing shortcuts to the
graphic functions, dashboard and CAN bus analyser Register to create an activation file to activate the
software. Help to run this help file and know the software
version Tabs: represent the various tabs in the main window. The
functions in these tabs are described in more detail in the following pages.
Status bar: It displays the current status of the software.
Displayed from left to right are The status of the connection with the ELM The status of the ELM The ECU undergoing diagnosis The make of vehicle selected The OBD protocol currently being used
Vehicle make selection window In order to obtain as much data as possible on connection, the
software will ask you to enter the make of vehicle on which you are doing a diagnosis.
This choice will display the corresponding description of the manufacturer’s specific DTCs.
If the make you want is not available, select Generic / Other Special cases: If your make does not appear but your vehicle is
fitted with the engine of one of the makes listed, select this make.
EOBD-Facile Manual
Outils OBD Facile – January 2015 3
4 Connecting to the vehicle (USB and RS232) First, when you open the application, connect to the vehicle using
the interface. You can connect in several ways: Automatically: The software automatically detects the port
number and communication speed of your ELM. Auto-detection is checked by default.
Important: This option is only possible with USB ELMs. The USB driver for the interface must first be installed.
Manually: The software tries to connect using the parameters
you entered in the Setup window – accessible from the File menu. (see image below).
Important: In manual (Auto-detection unchecked), you can use ELM32x RS232 or Bluetooth interfaces by correctly configuring the port parameters and by connecting with an (ELM327 USB) interface in the connection tab.
Configuring the initialisation time:
The ELM requires time to initialise the connection with the vehicle. By default, the waiting time is set to 14 seconds. If you are having connection problems, it may be helpful to increase this parameter.
Configuring the vehicle protocol:
The ELM can automatically detect your vehicle’s protocol. Unless you are an expert, leave the option on automatic. It may happen that protocol auto-detection does not work for several reasons. Most often it is because there are several valid protocols for your vehicle. In this case, you can force the ELM to connect with the desired protocol.
Confirm your parameters by clicking on OK, and proceed as
follows: Connect your interface to the vehicle Switch on the vehicle’s ignition (the engine indicator should be
lit) Start the connection using the Connection button on the
application EOBD-Facile will scan all the computers in your vehicle, and all
the functions supported by them. The result of this scan will be displayed in the text area of the connection tab.
Important: If you are having problems connecting to your
vehicle, read the information in the text area. Indications are displayed
to help you diagnose the problem. Note: Connection problems are never due to the fact that your software version is not registered!
When the message “The interface is connected and initialised”
appears, the software is ready to communicate with the vehicle Note 1: The status bar at the bottom of the main window
permanently displays the connection status.
Note 2: If you are having problems connecting, consult the chapter Problems connecting to the vehicle.
5 Connecting using a Bluetooth interface Before connecting using a Bluetooth interface, you must first pair
the interface with the computer. To do so, run the Bluetooth connection manager
If your interface has never been paired, you must first pair it. To
do, click on “add the device” to your list of known devices. For the pairing option, select “Enter the device pairing code”, you will be asked for a code. The code is 1234 in most cases.
Once the interface has been paired, display the devices and
connect the interface. The properties of the interface will give you the COM port number to be used when connecting with Bluetooth from the EOBD-Facile software (Interface ELM327 Bluetooth)
EOBD-Facile Manual
Outils OBD Facile – January 2015 4
6 Connecting using a WiFi interface In order to work, the ELM327 WiFi interfaces need to change the
parameters of your wireless connection network. Note, by changing these parameters, you will no longer have access to your internet connection, so the old settings will need to be restored when you have finished using your ELM327.
Proceed as follows. Go to your connection manager and connect
to the WiFiOBD interface
Then, right click on it, a menu will appear, select “Status”. The following window will appear
Click on “Properties”
Change the connection’s TCP/IP setting by entering a static IP address.
Set the IP as 192.168.0.11 and the subnet mask as 255.255.255.0
The new settings are complete. Close all windows and return to the EOBD-Facile application.
Select the connection with an ELM327 WiFi interface, the following window is displayed when you click on connect
Set the IP as 192.168.0.10
and the port number as 35000
Click on Next, the software will connect to the interface
Note: Depending on the WiFi interface manufacturer/merchant, the IP settings will not necessarily be the same. If this is the case, check the technical manual to find the IP address of the interface
EOBD-Facile Manual
Outils OBD Facile – January 2015 5
7 Configuring a new vehicle The dashboard function is highly efficient once the vehicle
settings have been entered in the software. See window below:
The following settings should be entered:
Fuel: select the fuel type for the vehicle Engine size: in cc (note: a 1.6 engine corresponds to 1600
cc) Volumetric efficiency: intake efficiency (used to calculate
the engine consumption). A standard vehicle is 80% efficient. If you note too high a difference between the vehicle’s consumption and that displayed by the software, change this setting.
Gear ratio: enter the speeds at 1000 rpm for each gear. To get this data, consult the technical data sheet for your vehicle or use the software’s graphic window to determine them.
8 Configuring the software
Units: metric to use the international system of units
(meter, grams, °C, etc.) or imperial (miles, pound, °F, etc.). Fuel price: Specify the price of the fuel (used by the
dashboard function) and the currency unit. Read freeze frames with defaults: This function will enable
you to see the engine status when faults appear directly from the diagnostic tab. This function will slow down reading of fault codes.
Enable fast thread execution. This function enables the software to increase data recovery speed. This function may cause some computers to crash (very rarely). If this is the case, uncheck this option.
Temporary files are created during the software usage. You can delete it at any time with the trash button.
EOBD-Facile Manual
Outils OBD Facile – January 2015 6
9 The “Diagnostic” tab This tab is used to diagnose the cause of the indicator light. The
function is available in the unregistered version of the software. Click Read to show the currently selected ECU and update the
window with: Confirmed fault codes The current status of the indicator The distance and time since the indicator has been lit (not available for all vehicles) The monitored test tables
The monitor test shows the status of the various systems: Not supported: Shows if the system is not monitored electronically by the ECU Completed means that all system tests have been successfully completed. Completed means that the system tests failed or that the ECU has not completed all the system tests (after cancelling a fault for example)
Description of fault codes: Click on the default code to update the associated description. The software uses the vehicle make selected on connection to show the exact description.
Engine status when the fault appeared (Mode 2) completes the
diagnostic data (only on the full version). These data show the conditions when the fault was detected (engine hot, idling, at full load, etc.)
Clear resets all data concerning the fault(s) stored in the ECU to
zero. Very important: Only use this function to find the cause of the failure and after having repaired it. A fault may sometimes reappear after several hundreds of kilometres. This operation will cancel all the fault codes and also the whole internal diagnostic history of the code(s) present: reset monitor tests, mileage when the fault appeared, etc.
After clearing, a message will confirm whether or not the
operation was successful.
EOBD-Facile Manual
Outils OBD Facile – January 2015 7
10 The “Advanced Diagnostic” tab This tab is used to refine the troubleshooting operation using the
vehicle’s advanced diagnostic functions. These functions are only available in the full version of the software.
Read (Mode 7): corresponds to the unconfirmed fault code.
This mode is very useful to check that the fault is indeed corrected after clearing. Usually, faults detected on the vehicle need several driving cycles before the indicator lights. During this confirmation phase, the faults are recorded in mode 7.
Read (Mode 10) corresponds to the permanent DTC.
Permanent faults cannot be deleted. They are very rarely used.
Read (Mode 2) is used to display the engine status when the fault
appeared. Select the index number of the fault you want (default 0). The software will display a table with the values of the associated engine sensors.
EOBD-Facile Manual
Outils OBD Facile – January 2015 8
11 “Sensors” tab The function is available in the unregistered version of the
software. This tab is used to read the actual value of the sensors. The list of
sensors displayed is automatic depending on the vehicle configuration. Click on start button to update the sensor value. You can also view the vehicle sensors using the Graph and log
function. These functions are described in the following chapters.
EOBD-Facile Manual
Outils OBD Facile – January 2015 9
12 The “Oxygen sensors” tab The “oxygen sensors” function is only available in the full version
of the software. Oxygen sensors are used in petrol vehicles to control the
injection. As a result, this function is only active on petrol vehicles. Note: On some petrol vehicles, the diagnostic for oxygen probes
is only accessible via the “Results of monitored systems” tab. Click Read to display the auto-diagnostic values for these sensors.
The ECU monitors measurements taken by these sensors permanently. The measurement must remain within the tolerances indicated by the software minimum and maximum. A sensor showing values outside this range is probably faulty.
Depending on the configuration of your vehicle (number of
cylinders, exhaust), several sensors are available. Select the sensor of your choice using the drop-down menu.
Oxygen sensors are named as follows:
Bank X Sensor Y X represents the bank number. Bank 1 corresponds to the
connection to cylinder no.1 on the vehicle. Most vehicles (3, 4 or 5 cylinders) only have one bank. On V6, V8, V10 engines, there are usually 2 banks (or more). Sometimes, several ECUs may be used on sports vehicles with more than 8 cylinders. In this case, switch from one ECU to the other using the menu “ECUs” to check all the oxygen sensors.
Y represents the number of the sensor. Sensor no. 1 is the one
closest to the cylinder (further upstream). Numbering continues from there. Sensor no. 2 is the one after the catalytic converter.
Below is an example of common configuration for vehicles with 3
or 4 cylinders:
EOBD-Facile Manual
Outils OBD Facile – January 2015 10
13 “Monitored system results” tab The function is only available in the full version of the software. The ECU permanently monitors the various systems regarding the
function it manages (engine, transmission, etc.). These results are available in this tab corresponding to mode 6 on EOBD.
Depending on the configuration of your vehicle, you will have access to data concerning: EGR, particulate filter, oxygen sensors, fuel management systems (canister, common rail, etc.).
This function is used to check that each system is operating
within its nominal range. The “Result” column will display “No” in red if this is not the case.
Note: depending on the make of vehicle, the descriptions of
systems and measurements may differ. The software may not know the description of some measurements. In this case, “Manufacturer specific ID Test” will be displayed.
EOBD-Facile Manual
Outils OBD Facile – January 2015 11
14 “Vehicle Info” tab The function is only available in the full version of the software. Click Read to display the vehicle identification data (VIN,
calibrations, etc.). This tab is divided into 2 zones. The upper zone displays the
general data for the various PIDs. Click on one of them to update the lower zone with the details of the selected PID.
The VIN (Vehicle Identification Number) allows the software to
“recognise” the vehicle characteristics. The IPTs (Performance monitoring during use) are also available
in this tab.
In the example below, the details are shown using the VIN of a
Renault vehicle.
EOBD-Facile Manual
Outils OBD Facile – January 2015 12
15 “Terminal” tab The function is only available in the full version of the software. It is used to send custom commands to the interface for the ELM
module (AT command) or to make specific OBD requests to the vehicle.
Example: Read the ELM version. Enter ATI and click Send The ELM will display its “name”.
For more details on the available commands, see the technical
data sheet for the ELM327 interface.
Scripts:
This function is used to save and replay commands for the ELM. File syntax is as follows:
Lines starting with the character # are comments displays on execution. [TX] followed by a text is used to send an order [WAIT] followed by a numerical value is used to add time in milliseconds. [CLS]: is used to clear the screen. [SAVE]: is used to save the result in a file.
Examples of scripts provided with the software Bus_CAN_11b_ECU_Moteur.txt: is used to accelerate data recovery speed on the CAN bus for vehicles operating with an 11bit CAN protocol.
EOBD-Facile Manual
Outils OBD Facile – January 2015 13
16 The “Graph and recording” window This window is run either from the shortcut on the sensor tab, or
from the “Special” menu. It is used to display the sensor values in the form of a graph and to record them in a file for later use.
16.1 Display values
In the “Data” tab, select the parameters you want to display, for each bank, using the drop down menus. Run continuous reading by clicking on “Start”. During reading, it is possible to show or hide a curve by un/checking “Displayed”.
You can also pause the recording at any time by pressing the
button “Start/resume”. Tip: You can show/hide the sensor selection area using the grey
arrow in the top right corner of the window. This is useful is you are working on a small screen (e.g. netbook)
At the bottom of the window, a status bar shows real-time
information from left to right: The length of the recording in seconds The refresh frequency of the values in milliseconds
(and the average in brackets) The current value on bank 1 The current value on bank 2 The current value on bank 3 The current value on bank 4
Stop the recording: Click Stop to stop recording. A summary is
displayed with, for each active bank, some statistics. To save the recording, click Save as. The data are saved in .csv format with commas as separators. This type of file can be opened in Excel.
Placing markers: The “Mark” button can be used to place markers
on the graph. They will appear in a little yellow bow with a number. Markers are easily inserted in the recording file, making it easier in long recordings to find the area you wish to analyse.
Snapshot: save the current image of the graph in an image file. Note: Each recording is saved by default in the file
DernierEnregistrement.txt in the software’s data directory. Any new recording will replace this file.
16.2 Display/record options
In the “Recording” tab, select the display you require.
Scroll time between 30 seconds and 10 minutes. Graph background colour: black or white Display or hide the graph grid.
Legend:
Vertical axis scale is selected automatically by the software. You may use your own scale by setting minimum and maximun values for bank 1 and 2.
EOBD-Facile Manual
Outils OBD Facile – January 2015 14
16.3 Replay a recording
The function is only available in the full version of the software. This function is used to reload a previous recording saved in the
software. The data can be analysed and replayed in the data graph window.
In the “Replay” tab, open the file you want to replay. The
window will change aspect. A horizontal bar with buttons will appear with a cursor used to navigate through the recording. A black line shows your current position.
When you have finished the replay, click Close to return to
normal mode (recording).
The “Replay” tab contains data in the open file and the statistics
on the data in the file.
EOBD-Facile Manual
Outils OBD Facile – January 2015 15
16.4 Smart triggers
The function is only available in the full version of the software. This function is used to start reading and stop recording in
graphic mode automatically and according to a condition. This is useful for performance measurements such as standing starts for a 0 to 100 kph.
The software includes 4 preset triggers:
0-100 kph 80-120 kph 400m standing start 1000m standing start
Other triggers can be set by changing the recording start and stop
conditions. For example, standing start tests up to 130 kph are possible by changing the stop conditions with the value 130.
Important: The settings used to trigger the recording (engine
speed, vehicle speed, etc.), must also be present in the settings to be recorded in order to work.
Once the trigger is configured, click “Start”. The following
window will appear and the recording will start itself when the condition is fulfilled.
16.5 Exporting recording to a spreadsheet
The function is only available in the full version of the software. Recordings can be exported using the graph and recording
function. The data are saved in a .csv file with commas as separators. Each line in the file corresponds to a point of the recording and each line contains several fields. The first filed corresponds to the recording time (in seconds), and then for each active bank, a field corresponding to the sensor PID, followed by a field indicating its value.
Example: Time;Engine speed;Vehicle speed Time;O-0C-0;O-0D-0 sec;rpm;kph 0,068;5758,000;113,000 0,131;5758,000;113,000 0,198;5801,500;113,000 0,256;5801,500;114,000 At t = 0.068: Engine speed = 5758 rpm Vehicle speed = 113 kph At t = 0.131: Engine speed = 5758 rpm Vehicle speed = 113 kph At t = 0.198: Engine speed = 5801.5 rpm Vehicle speed = 113 kph At t = 0.256: Engine speed = 5801.5 rpm Vehicle speed = 114 kph A sample file is available in the EOBD-Facile installation
directory: Exemple_DA.xls The first tab in the Excel file (User instructions) explains in detail
the procedure for importing a recording file. The second tab shows the data in raw table form. In the sample, a
standing start simulation where the 4 banks were configured to measure speed, engine speed, flow and boost pressure (turbocharged engine).
The third tab shows the same data in graph form. Using spreadsheet functions, it is possible to develop conversion
formula or easily extract statistics on your measurements.
EOBD-Facile Manual
Outils OBD Facile – January 2015 16
17 The “Dashboard” window This function is accessible from the Special / Dashboard menu
enabling you to make consumption measurements for petrol and LPG vehicles only.
In order to obtain relevant data, remember to enter the software
options in the vehicle tab with the cubic capacity, the fuel type and the gearbox ratios.
Important: For consumption to be calculated, your vehicle must
be able to measure one of the 2 following values: Intake manifold pressure (PID 0x0B) Intake air flow (PID 0x10)
Several parameters are available in the dashboard electronic
display (for petrol/LPG vehicles) Vehicle speed Engine speed The engaged gear (N for neutral) Distance covered (Odo.) Quantity of air taken in (Qair) Current consumption (in L/100km) Current consumption (in L/hr) Engine load (in %)
Journey statistics: During the whole journey, the software will record and calculate
statistics to analyse the driving style and vehicle consumption. The image below shows the various parameters calculated.
The journey data can be saved in a *.csv file for later analysis with another software (a spreadsheet for example). It is also possible to save the data below in the form of an .html file (for printing for example).
EOBD-Facile Manual
Outils OBD Facile – January 2015 17
18 The “CAN bus analyser” window This function is accessible from the Special / CAN bus analyser
menu enabling you to spy on a CAN bus via an ELM interface. Important: If your vehicle does not operate in CAN bus, force
the interface in one of the CAN protocols and start the connection. The connection will fail but you will still be able to use the CAN bus analyser function.
18.1 Display frames
The frames can be displayed in two ways: Time: the frames are displayed in chronological order By ID: in this case, frames with the same ID are
always displayed on the same line. Yellow highlighting shows the changes.
The status bar (bottom of the window) contains from left to
right: The 11bits or 29 bits CAN protocol The Cnt statistics showing the number of frames
received and Fps showing the number of frames received per second.
The status of the CAN filters. Reading can be paused at any time. A A contextual menu is also
available by right clicking on the frame display area to: Save the read result in a file Clear the area Copy the read result into the clipboard
18.2 Filtering the CAN bus
Depending on the CAN buses spied on, the quantity of frames displayed can rapidly grow and saturate the ELM interface causing a “Buffer overflow!” error. To solve this problem, either increase the communication speed with the ELM or define a filter to only display the frames that interest you.
The principle of filtering is to choose CAN identifiers that you want to display. 2 types of filtering are possible:
Software filtering: this is display filtering in EOBD-Facile. It
has the advantage of being easy to configure but does not solve ELM buffer overflow problems. With this type of filtering, the ELM will continue to send all frame continuously.
Hardware filtering: this is a filter than can be set within the
ELM. Thus it avoids saturating the link between the ELM and EOBD-Facile. Click on Update to send the new filtering parameters to the interface. A Test button enables you to test the IDs you want to exclude/accept in the configured filter.
EOBD-Facile Manual
Outils OBD Facile – January 2015 18
19 PID Decoder This function accessible from the File / PID decoder menu, is
used to interpret the data in the “vehicle list” tables on our website. Copy the lines of the table and select the mode, then click Decode to get a list of supported PIDs.
20 Customisation
20.1 How to add specific manufacturer codes
Edit the file CODES-FR.ini located in the “Documents\EOBD-Facile\data\DTC” directory and add your codes in the form Pxxxx =Description of the code. Then, create one section for each make of vehicle for which you want to add codes. For example, to add the trouble codes for Peugeot and BMW, proceed as follows:
[Peugeot] P1101=MAF (Mass Air Flow) sensor out of self-test range P1102=MAF (Mass Air Flow) sensor in range but lower than expected P1103=MAF (Mass Air Flow) sensor in range but higher than expected [BMW] P1083=Fuel Control Limit Mixture too lean (Bank 1 Sensor 1) P1084=Fuel Control Limit Mixture too rich (Bank 1 Sensor 1)
Once your file is updated, you can test it using the terminal tab and entering the following order line:
_TEST_DTC P1101 Before starting to translate and add numerous definitions,
remember that EOBD-Facile already includes more than 5000 definitions to date. As well as generic definitions, many specific definitions have been translated and added by us for makes such as Peugeot, Citroën, Ford, BMW, Mazda, Toyota, Fiat, etc.
21 Error messages:
21.1 Errors from the ELM interface
ELM error detected: Buffer overflow! The flow of data from the OBD communication is greater than that of communication with the PC. This error is frequent with vehicles operating in CAN bus. Reconfigure the communication speed to solve this error (See chapter Graphs / Improving data recovery speed).
ELM error detected: Bus busy! The communication bus is busy and the interface cannot initialise communication.
ELM error detected: Bus error! A corrupted signal has been detected. Typically when the vehicle is started while communication is in progress.
ELM error detected: data error! The data read are incorrect.
ELM error detected: Return signal error! The return signal is inconsistent. The signal generated on the bus does not correspond with what the ELM is attempting to send. Mostly, this is a material wiring issue.
ELM error detected: Reception signal error! Data received are not valid, may be due to incorrect configuration of the communication speed on the CAN bus.
Interface reset detected! Reconnect the software to continue! The software has detected restart of the interface, usually due to loss of power. To continue to use the software, reconnect.
For more information about these errors, please consult the
technical documentation on your ELM circuit.
EOBD-Facile Manual
Outils OBD Facile – January 2015 19
22 Frequent problems, tips
22.1 Connection problems with the vehicle
List of the most common causes of connection problems:
The USB driver for the interface is not installed The vehicle is not compatible with the OBD (Only
vehicles since 2001 for petrol and 2003 for diesel are compatible)
The vehicle ignition was not switched on for the connection
The communication parameters are incorrect In 90% of cases, we suggest you keep the option auto-
detection of the vehicle protocol If this does not work, try to force the protocol in ISO 14230 (5
baud init). ELM type interfaces sometimes encounter auto-detection problems for this protocol
22.2 Asynchronous socket error
This error arises with WiFi interfaces that are not correctly configured in the wireless connection properties. For more details, consult chapter “Connecting with a WiFi interface”.
22.3 Fault deletion problem
When you press delete, the software displays an error message “Incorrect conditions”. For safety reasons, faults cannot be deleted when the engine is running. Switch off the engine and try again.
22.4 Renault "hands-free" kit
Vehicles fitted with this option can be connected using our software. Follow the procedure below to run diagnostics on the vehicle:
Close the door. Put the car in first gear. Do not press the brake or the clutch. Press the START/STOP button for about 15 seconds. Contact will be made and remain active for 30 minutes.
22.5 Repair tutorials
On your website you can found repair sample for the following
faults: P0110 : Air intake temperature sensor P0380 / P0670 : Glow plugs P0301 / P0302 / P0303 / P0304 : Misfires
22.6 Contacts
If you have any questions or suggestions about this help file, contact us at the following address: