Upload
kbekker104
View
928
Download
3
Tags:
Embed Size (px)
Citation preview
4545 Enterprise, Boise, Idaho 83705Tel: (208) 342-6823 / (800) 727-9907 - Fax: (208) 342-6832 / (800) 627-0929
Safe bathing for people of all abilitieswww.best-bath.com
"HG" ADA Shower Overview
ADA/Cal Title 24/TAS "Change of Level" allowed 1/2" (1: 2) change in level
center line of drain hole
drain cut-out size 8"x8" or 8" diameter
1/2"
1/4" flooring
Integral level support (adhered by others)
Integral level support (adhered by others)
4"
drain cut-out size 8"x8" or 8" diameter 4"
3/8"
.75 Curb/bottom for roll-in showers
Page 1
.5 Curb/bottom for transfer showers
3/8"
Safe bathing for people of all abilitieswww.best-bath.com
Curb Details
1/2"center line of drain hole
vinyl flooring
FLOOR
Page 2
Safe bathing for people of all abilitieswww.best-bath.com
Drain Details
Cross Section of Standard, Cored Shower Bottom (installed)
Cross Section of Low Profile Shower Bottom (installed)
3/16" Thick Fiberglass
Plywood Core
1/8" Thick Fiberglass
Build up or recess per code
1/4" Thick Fiberglass
Integral Leveling Material
Epoxy Adhesive (by installer)
1/4" Steel Flatbar
Build up or recess per code
6"
8"
34" MIN.
34" MIN.
Page 3
Safe bathing for people of all abilitieswww.best-bath.com
Wall Section Detail
Gelcoat finish(color)
Barrier coat
Fiberglass laminate
Fiberglass laminate
1/2" Plywood
Cut-away view of HG unit wall
Page 4
Safe bathing for people of all abilitieswww.best-bath.com
Cross Section of HG Wall
1-1/8" Overall Wall Thickness
5/8" Space
Top and Front Nailing Flanges
1/2" Plywood
Inside Wall Surface
Face of Stud
Laminate Schedule - Uncored Bottoms - Gel Coat - Barrier Coat - Hydrate (bed) - Steel Flat Bar - Hydrate (top) - Level Block(s) - Integral Leveling Support
One Piece Shower HG/CG (Hospital Grade/ Commercial Grade) with 12 (1.25") or LOWER curb
same on this side
corner reinforcements(not on smooth wall models)
1/4" FRP Laminate andIntegral Leveling Support(7 # Urethane Compound)
Laminate Schedule - Walls - Gel Coat - Barrier Coat - Hydrate (bed) - Plywood Core - Hydrate (top)
18 mil30 mil90 mil (3/32")1/2"130 mil (1/8")
Material Cut ListWallsas required 1/2" Plywood 4" x 8" " 8" x 8" " 2" x 8" " 2" x 12"as required 3" x 5" HD cards
Material Cut ListBottomSteel Flat Bar 1/4" x 1-1/4" x XX"
18 mil30 mil130 mil (1/8")1 length at curb130 mil (1/8")
Laminate Schedule - Cored Bottoms - Gel Coat - Barrier Coat - Hydrate (bed) - Plywood Core - Hydrate (top) - Level Block(s)
Page 5
Safe bathing for people of all abilitieswww.best-bath.com
Laminate Schedulesof HG Showers
One Piece Shower HG/CG (Hospital Grade/ Commercial Grade) with 15 (1.5") or HIGHER curb One Piece Tub/shower HG (Hospital Grade/ Commercial Grade)
same on this side
corner reinforcements(not on smooth wall models)
Full Plywood
Cored bottomFull Plywood
Laminate Schedule - Walls - Gel Coat - Barrier Coat - Hydrate (bed) - Plywood Core - Hydrate (top)
18 mil30 mil90 mil (3/32")1/2"130 mil (1/8")
Material Cut ListWallsas required 1/2" Plywood 4" x 8" " 8" x 8" " 2" x 8" " 2" x 12"as required 3" x 5" HD cards
Material Cut ListBottomas required 3/4" Plywood
18 mil30 mil130 mil (1/8")3/4"130 mil (1/8")
Steel Flat Bar
Full Plywood
Full Plywood
Page 6
Safe bathing for people of all abilitieswww.best-bath.com
Water Containment Solutions
2-1/2"
3-1/2"
cut to fit per model
- Material: EPDM Rubber, 50 Durometer, Endcaps: injection molded Vyram rubber- Finish: Kits are available in both Grey and Beige- Dimensions: Will fit on any Access ADA or Barrier Free model offered- Available for other Brands.- Installation: Self-Adhesive.
Kit Contents: - 1 ea. Specified length of WaterStopper - 2 ea. Specified size end caps - 2 ea. Alcohol wipes - Installation Instructions
Cross Section Flattens under wheelchair
with WaterStopper
138"
114"
Endcap 2-1/4" radius
Front view Front view
Endcap 3/8" radius 316"
Tape-weighted curtain
without WaterStopper
Tape-weighted curtain
- Material: Powder coated aluminum, .100" thick.- Finish: Color WHITE, special colors available for quantity orders.- Dimensions: Made to fit any ADA or Barrier Free model offered by Best Bath Systems.- Available for other brands (cut to fit on-site).- Installation: Simple, removable installation with silicone caulk.
Kit Contents: - 1 ea. Specified TAS (cut to fit) - 1 ea. Cartridge of silicone caulk (white) - Installation Instructions
Silicone Shower Bottom
Bathroom Floor
Silicone
TAS-M (Mini)TAS
"The solution to wet floors"
2"
2-3/8"
cut to fit per model
Specifications for The WaterStopper Kit
Specifications for The Semi-permanent Threshold Adaptor
Page 7
Safe bathing for people of all abilitieswww.best-bath.com
Flange Trim Kit FTK-R-5-125
8"
1 ea Backwall section1 ea Left front and top section1 ea Right front and top section10 ft. 5/16" Butyl tape 3M #8621 5/16" thick, 1/2" wide1 ea Silicone (white)
Kit consists of
InstallationMeasure the distance between the drywall at the back wall.Trim or sand the molding sections to size with a hacksaw. Cut the Butyl tape in 2" pieces, fold double as neededand stick to the nailing flange and drywall at 8" intervals.Press the molding in place.Repeat with the rest of the sections.Caulk all around the edges.
MaterialMatching gelcoat fiberglassInstall with butyl tape and caulk
R 1/8"
Moldings shown before installation
Cross Section of Molding
ApplicationFor use as an easy way of covering the nailing flange where there already is drywall or other wall material BEHINDthe shower or tubshower.
Flange Trim Moulding
Shower Nailing Flange
Latex caulk (paintable)
Screw head
Silicone caulk
Drywall
Cross Section of Molding installed
Butyl Tape #8621
stud
stud
1-1/4"
1/2"1/16"
Drywall
Butyl tape
Page 8
Safe bathing for people of all abilitieswww.best-bath.com
One Hour Fire RatedDrywall Stud Pocket
PLAN
1st Drywall
2nd Drywall
1st Drywall
2nd Drywall
Shower Wall
Studs
DETAIL A iso view at top of wall (installed)
Nailing Flange
Nailing Flange
2nd Drywall
Page 9
Safe bathing for people of all abilitieswww.best-bath.com
90° Reveal and ConventionalFlange Details
PLAN
5/8" Drywall 5/8" Drywall
Stud
2"
DETAIL A"Reveal 90" Feature
1"
1"
DETAIL BDETAIL A
DETAIL BConventional
DETAIL A iso view at top of wall (installed)
Studs
Drywall
Studs
DETAIL Btop of wall(installed)
Nailing Flange
Drywall
5/8" drywall
stud
Page 10
Safe bathing for people of all abilitieswww.best-bath.com
SEE PAGE 11 FOR ADDITIONALIMPORTANT INSTRUCTIONS
A=approx. 6"A
Do not walk on bottomuntil epoxy has set up
TIP: Also put epoxy between 2 pcs. of scrap wood to monitor cure.
Screw throughflanges every 8"
Epoxy
8"x 8" or8" diam.
Brace or weigh down the 2x4s so that they are tight all along the shower floor.
Epoxy
Epoxy Adhesive:3/4" dollops every 8" min.
3/4" high
PLAN for Showers Larger than 38" x 38"
Storage: Do not Rest onthe Bottom Once the Drain
Fitting is Installed
Unscrew this blockbefore installing
NOTE: The drain cut-out must be8" diam. or 8" x 8" and back filledif it is larger to prevent flexing.
PLAN for Rear Drain Showers
PLAN for 38" x 38" showers only
Use straight 2x4s
Use straight 2x4s
Use straight 2x4s
A
LPB1
Page 11
Safe bathing for people of all abilitieswww.best-bath.com
Showers (1-piece) withLow Profile Bottoms
1. Check the stud pocket for level and correct dimensions and the drain hole in the floor for the correct distance to the studs. The floor must be level +/- 1/8 inch.2. The shower drain must be centered in an 8" cut-out in the floor (refer to specification or the actual shower). See drawing above. 3. Have the plumber install the drain fitting. DO NOT store the unit resting on the drain.4. Prepare the drain pipe to receive the drain.5. Clean the floor and the pan's underside. The floor may be damp but no standing water.6. The leveling material has been scuffed up at the factory. Clean off any debris stuck to it. 7. Remove the plywood strip that is screwed to the leveling block at the back.8. Draw a line where the curb will be.
9. Put the unit face-down in front of the pocket.10. Apply the epoxy adhesive to the floor. (See illustration on the front page) At the same time, glue some scrap wood together as a cure time sample for later on.11. Tip the shower into position, making sure it is positioned at the line drawn in step 8. Avoid stepping on the bottom until the epoxy has set up.12. When level, screw through the flanges.13. Use 2x4 boards to brace or weigh down as shown over until snug to the shower floor. 14. Make sure the bottom has adequate drain- slope by pouring water in it or with a level. 15. Check the cure time sample from step #10 and when fully bonded, remove the bracing boards or after no less than 2 hrs. (more if the floor is cold)
Installation:
drain fitting (do not store the pan upright resting on the drain)
8"
CL
Epoxy adhesive
Epoxy adhesive (8" o.c., see over)
unscrew before installation
1/4" thick fiberglass
factory leveling material
CROSS SECTION OF BOTTOM(installed)
NOTE: The drain cut-out must be 8" diam. or 8" x 8". If it is larger, back-fill to prevent flexing.
3/4" min.
The extremely low profile of this shower bottom may eliminate the need for recessing.In order to get full, permanent contact with the floor, it MUST be installed per these instructions.
Failure to follow these instructions may result in failure not covered by warranty.
LPB1
LCS26337A75BHG - LEFT PLBG "ACCESSIBLE"
--- ---ABCDE
--- ------ ------ ------ ---
A
A
3112"
63"
201 2"
381 2"
1"
60" 1"
783
4"3
4" 38"
18"
112"
34"
18"
37"
CENTEREDCENTERED
27"
40"46
"60
"
21"
27"
1
5
4
5
7
3
2
OPTION VERIFICATION MODEL: QTY:
CB:
DB:DATE
CHANGEREV DATE
NOTES:SHEET 1 OF 2
/ /
ACCEPTED AS CORRECT BY:
X
DRAWING NUMBERCOMPANY:PROJECT: SCALE
DIV. OF FIBERGLASS SYSTEMS NC.www.best-bath com 1-800-727-9907
INT. LEFT ELEVATION FRONT ELEVATION INT. RIGHT ELEVATION
PERSPECTIVE - N.T.S.TOP VIEW
MA
PVR 1/2" = 1'-0"
75"
2"2
8 8
6
36"
ADA COMPLIANT
Rough-in stud opening +1/4” -0” nominal dimensionsAll vertical accessory dimensions are measured from the floor of the shower.Best Bath Systems, Inc. retains ownership of all product designs and anyproprietary information may not be disclosed to its competitors, their agentsor affiliates.
SURFACE MOUNT SOAP DISH
CURTAIN ROD
3
10
SYMMONS S-96-300-B30-L-X-V, VALVE AND GLIDE BAR KIT
CORRUGATED PROTECTIVE PAD
OPTION VERIFICATION MODEL:
COMPANY:PROJECT:
14
PARTS LIST
5
1QTY.KEY
32
4
6
87
109
1112
COLORDESCRIPTION PART NUMBER
13
20
1615
1817
19
2221
23
NOTES:UNIT WEIGHT:
INSTALLEDBY
OTHERSFACTORY
INSTALLEDMARK
LOCATIONONLY
PRE-DRILLHOLES
DATE
DRAWING NUMBER
SHEET 2 OF 2REFER TO SHEET 1 OF 2 FOR ACCESSORY LOCATIONSDIV. OF FIBERGLASS SYSTEMS NC.www.best-bath com 1-800-727-9907
SECTION A-A - SCALE: 3" = 1'-0"
PERSPECTIVE - N.T.S. LAMINATE DETAIL C - SCALE: 3" = 1'-0"
1
1
1
1
2
1
1
1
1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
GREY
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
KTWSG5L
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
32" x 36" x 1- 14" L GRAB BAR
34" x 21" FOLD DOWN SEAT WITH SWING DOWN LEGS, PHENOLIC
AQA MOUNTING BRACKET SET
FULL 12" PLYWOOD BACKING
T-SHAPED RUBBER WATER STOPPER KIT
NO CAULK BRASS DRAIN WITH POLISHED STAINLESS STEEL SCREEN
Product Guide Specification LCS26337A75BHG Accessible Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) Three-Part Section Format and Page Format, contained in the CSI Manual of Practice. The section must be carefully reviewed and edited by the Architect to meet the requirements of the project and local building code. Coordinate with other specification sections and the drawings. Delete all "Specifier Notes" when editing this section. SECTION 15410 A.D.A. COMPLIANT BATHING UNITS Specifier Notes: This section covers Best Bath Systems A.D.A. Compliant showers of composite fiberglass-reinforced construction. Consult Fiberglass Systems for assistance in editing this section for specific applications. PART 1 GENERAL 1.1 SECTION INCLUDES A. ADA Compliant, one-piece fiberglass showers. 1.2 RELATED SECTIONS A. Section 15400 – Building services: Piping. 1.3 REFERENCES A. ASTM E 162 - Surface Flammability of Materials Using a Radiant Heat Energy Source. B. NFPA 258 - Determining Smoke Generation of Solid Materials. 1.4 SUBMITTALS A. Comply with requirements of Section 01300 - Submittals. B. Product Data: Submit manufacturer's product data, including composite fiberglass material description, construction details,
dimensions, accessories, fixtures, and finishes. C. Samples: Submit one 6 inch square sample of composite fiberglass material in each color specified for Architect's approval. 1.5 QUALITY ASSURANCE A. Codes and Standards: Comply with the following codes and standards. 1. ADA Accessibility Guidelines for roll-in showers. 2. ANSI Z124.2 - Plastic Shower Receptors and Shower Stalls. 3. ANSI A117.1 Accessible and Useable Buildings and Facilities 4. ASTM F 462 - Consumer Safety Specification for Slip-Resistant Bathing Facilities. 5. IAMPO/UPC – Uniform Plumbing Code.
6. California Building Code, Chapter 11B Accessibility to Public Buildings, Public Accommodations, Commercial Buildings and Publicly Funded Housing.
1.6 DELIVERY, STORAGE, AND HANDLING A. Delivery: Deliver bathing units to site in manufacturer's original, unopened containers and packaging, with labels clearly
indicating manufacturer and model number. B. Storage: Store bathing units indoors in an area protected from damage and in accordance with manufacturer's instructions. C. Handling: Protect bathing units during handling and installation to prevent damage. 1.7 WARRANTY A. Provide manufacturer's limited warranty against structural and finish defects for 3 years from date of installation.
LCS26337A75BHG Accessible 1 of 3
PART 2 PRODUCTS 2.1 MANUFACTURER A. Best Bath Systems, 4545 Enterprise Street, Boise, Idaho 83705, Phone 800-727-9907, Fax 800-627-0929. 2.2 A.D.A. COMPLIANT BATHING UNITS
One piece fiberglass shower stall, meeting A.D.A. and CA. accessibility code criteria. 2.3 MATERIALS A. Gelcoat Finish: Sanitary ware grade gelcoat. Minimum cured thickness 0.015 inch. Barrier Coat: Ceramic fiber filled polyester resin coating to enhance gloss and surface hardness. B. Skin Layer: Glass fiber and polyester resin layer to provide resilient skin against the gelcoat finish. C. Filled and Cored Layer: Fiberglass laminate with minimum 15 percent fiberglass content and filled resin completely
encapsulating a 1/2 inch plywood core on most flat surfaces, to provide stiffness as well as backing for grab bar and seat anchoring. All core termination edges beveled. Floor of ¼ inch thick fiberglass laminate with an integral level support compound bonded to it.
1. Flame Spread Rating: Less than 75 in accordance with ASTM E 162. 2. Smoke Generation: Less than 450 in accordance with NFPA 258. Specifier note: Select plumbing hand. Model LCS26337A75BHG. “Accessible” The unit measures 63 inches wide x 37-1/2 inches deep x 78-3/4 inches high. [Right][Left] hand plumbing. B. Color: Best Bath White 2.5 ACCESSORIES Specifier Notes: Consult Best Bath Systems for assistance in specifying accessories for specific applications. Coordinate right and left hand accessories with bathing unit models. Select brand of mixing valve and delete the other. A. Mixing Valve: [Symmons S-96-300-B30-L-X-V] Brass, pressure balanced, lever handle valve, plumbing elbow, polished
chrome finish. Hand held shower with applicable hose. Vertically mounted, 30 inch long glide bar, polished chrome finish and cradle with adjustable height setting for hand held shower.
B. Soap Dish: Two (2) white cast polyester surface mounted soap dishes, one (1) each at the sitting level and the standing level. C. Folding seat: 34” x 21”, White phenolic slat seat surface, stainless steel frame and swing down legs. D. Grab Bar 32” x 36” corner type, 1-1/4 inch diameter, stainless steel, 18 gauge. E. Shower Curtain Rod: 65 inches, stainless steel, 20 gauge, 1 inch OD, with mounting flanges. F. Drain: No-Caulk, brass body with polished stainless steel screen. G. Water Stopper kit, collapsible 60 inch grey “T” shaped retainer with large radius end caps. H. Corrugated cardboard interior bottom protector. I. Shower system individually palletized, faced at the opening with corrugated protector and stretch wrapped.
LCS26337A75BHG Accessible 2 of 3
PART 3 EXECUTION 3.1 EXAMINATION A. Inspect areas where ADA compliant bathing units will be installed. Notify the Architect of conditions that would adversely
affect the installation or subsequent utilization of bathing units. Do not proceed with installation until unsatisfactory conditions are corrected.
3.2 INSTALLATION A. Install in accordance with manufacturer's instructions which are different from those of conventional one piece shower units
in that the unit may be installed directly on top of the flooring and still meet the A.D.A. 1/2 inch maximum curb height requirement. To allow for this the following needs to be done:
1. The hole around the drain needs to be 8 inch diameter. 2. The unit needs to be adhered to the floor using an epoxy adhesive that is provided by the shower manufacturer. 3. Flooring needs to be brought up to the bevel on the curb.
B. Install barrier free bathing units level, plumb, and square with flat wall surfaces. C. Touch-up minor damaged surfaces caused during installation. Replace damaged components as directed by Architect. 3.3 ADJUSTING A. Test and adjust mixing valves and hand held showers for proper and efficient operation, including water temperature,
pressure, and volume. 3.4 CLEANING A. Clean surfaces in accordance with manufacturer's instructions. B. Do not use abrasive cleaners, metal scrapers, or wire brushes. 3.5 SCHEDULE Specifier Notes: Provide a schedule if two or more ADA compliant bathing units are specified with different model numbers or accessories. Identify each unit separately. Coordinate schedule with location of units indicated on drawings. This is an optional location for the schedule, rather than on the drawings. END OF SECTION APPROVED ARCHITECT: NAME: TITLE: DATE: ENGINEER: NAME: TITLE: DATE: OWNER: NAME: TITLE: DATE:
LCS26337A75BHG Accessible 3 of 3
LCS26337A75BHG - LEFT PLBG "ADAPTABLE"
--- ---ABCDE
--- ------ ------ ------ ---
A
A
3112"
63"
201 2"
381 2"
1"
60" 1"
783
4"3
4" 38"
34"
18"
37"
CENTEREDCENTERED
27"
40"46
"60
"
21"
27"
1
5
4
5
6
3
2
OPTION VERIFICATION MODEL: QTY:
CB:
DB:DATE
CHANGEREV DATE
NOTES:SHEET 1 OF 2
/ /
ACCEPTED AS CORRECT BY:
X
DRAWING NUMBERCOMPANY:PROJECT: SCALE
DIV. OF FIBERGLASS SYSTEMS NC.www.best-bath com 1-800-727-9907
INT. LEFT ELEVATION FRONT ELEVATION INT. RIGHT ELEVATION
PERSPECTIVE - N.T.S.TOP VIEW
MA
PVR 1/2" = 1'-0"
75"
2"2
7 7
36"
ADA COMPLIANT
Rough-in stud opening +1/4” -0” nominal dimensionsAll vertical accessory dimensions are measured from the floor of the shower.Best Bath Systems, Inc. retains ownership of all product designs and anyproprietary information may not be disclosed to its competitors, their agentsor affiliates.
SURFACE MOUNT SOAP DISH
CURTAIN ROD
3
9
SYMMONS S-96-300-B30-L-X-V, VALVE AND GLIDE BAR KIT
CORRUGATED PROTECTIVE PAD
OPTION VERIFICATION MODEL:
COMPANY:PROJECT:
14
PARTS LIST
5
1QTY.KEY
32
4
6
87
109
1112
COLORDESCRIPTION PART NUMBER
13
20
1615
1817
19
2221
23
NOTES:UNIT WEIGHT:
INSTALLEDBY
OTHERSFACTORY
INSTALLEDMARK
LOCATIONONLY
PRE-DRILLHOLES
DATE
DRAWING NUMBER
SHEET 2 OF 2REFER TO SHEET 1 OF 2 FOR ACCESSORY LOCATIONSDIV. OF FIBERGLASS SYSTEMS NC.www.best-bath com 1-800-727-9907
SECTION A-A - SCALE: 3" = 1'-0"
PERSPECTIVE - N.T.S. LAMINATE DETAIL C - SCALE: 3" = 1'-0"
1
1
1
1
2
1
1
1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
GREY
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
KTWSG5L
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
32" x 36" x 1- 14" L GRAB BAR
AQA MOUNTING BRACKET SET
FULL 12" PLYWOOD BACKING
T-SHAPED RUBBER WATER STOPPER KIT
NO CAULK BRASS DRAIN WITH POLISHED STAINLESS STEEL SCREEN
Operation:Seat is automatically held in a raised position by a phenolic cross member attached to the front and rear support legs. When theseat is lowered into its down position, the swing down leg automatically aligns the front and rear support legs with the help ofthe phenolic cross members.
Specifications:
Materials:FRAME: Type 304 (18-8) S.S. tubing, 1 1/4" (32mm) x 18 ga. (1.2mm) square main frame with 1" (25mm) x 18 ga. (1.2mm) round cross members.
WALL FLANGES: Type 304 (18-8) S.S. 10 ga. (3.4mm) x 3" (76mm) diameter, heliarc welded to 1" (25mm) supports, and to 1 1/4" (32mm) round x 12 ga. (2.7mm) frame hinge couplings. Three mounting holes per flange.
SWING DOWN LEGS: "H" shaped yoke of Type 304 (18-8) S.S. 1" diameter x 18 ga. round tubing, heliarc welded to 1 1/4" (32mm) round x 12 ga. (2.7mm) frame hinge couplings.
SEAT CHOICE: Phenolic Slat, 1/2" (13mm) x 3" (78mm) bolted to frame with stainless steel screws and nuts.
INSTALLATION: All shower seats must only be installed using sufficient in-wall backing material.
Architectural Specifications:
-FOLDING SHOWER SEAT WITH SWING DOWN LEGS-PHENOLIC SLATS-SIZE: 34" X 21" L-SHAPE
Shower seat with swing down legs. The swing down legs automatically level when the seat is lowered to a horizontal sittingposition. the seat automatically locks itself when swung into its "up" position with the use of the phenolic cross members.
Page 19
Safe bathing for people of all abilitieswww.best-bath.com
34" x 21" Folding SeatPhenolic Slat with Legs
34"
131
2"
201
2"
18"
Product Guide Specification LCS26337A75BHG Adaptable Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) Three-Part Section Format and Page Format, contained in the CSI Manual of Practice. The section must be carefully reviewed and edited by the Architect to meet the requirements of the project and local building code. Coordinate with other specification sections and the drawings. Delete all "Specifier Notes" when editing this section. SECTION 15410 A.D.A. COMPLIANT BATHING UNITS Specifier Notes: This section covers Best Bath Systems A.D.A. Compliant showers of composite fiberglass-reinforced construction. Consult Fiberglass Systems for assistance in editing this section for specific applications. PART 1 GENERAL 1.1 SECTION INCLUDES A. ADA Compliant, one-piece fiberglass showers. 1.2 RELATED SECTIONS A. Section 15400 – Building services: Piping. 1.3 REFERENCES A. ASTM E 162 - Surface Flammability of Materials Using a Radiant Heat Energy Source. B. NFPA 258 - Determining Smoke Generation of Solid Materials. 1.4 SUBMITTALS A. Comply with requirements of Section 01300 - Submittals. B. Product Data: Submit manufacturer's product data, including composite fiberglass material description, construction details,
dimensions, accessories, fixtures, and finishes. C. Samples: Submit one 6 inch square sample of composite fiberglass material in each color specified for Architect's approval. 1.5 QUALITY ASSURANCE A. Codes and Standards: Comply with the following codes and standards. 1. ADA Accessibility Guidelines for roll-in showers. 2. ANSI Z124.2 - Plastic Shower Receptors and Shower Stalls. 3. ANSI A117.1 Accessible and Useable Buildings and Facilities 4. ASTM F 462 - Consumer Safety Specification for Slip-Resistant Bathing Facilities. 5. IAMPO/UPC – Uniform Plumbing Code.
6. California Building Code, Chapter 11B Accessibility to Public Buildings, Public Accommodations, Commercial Buildings and Publicly Funded Housing.
1.6 DELIVERY, STORAGE, AND HANDLING A. Delivery: Deliver bathing units to site in manufacturer's original, unopened containers and packaging, with labels clearly
indicating manufacturer and model number. B. Storage: Store bathing units indoors in an area protected from damage and in accordance with manufacturer's instructions. C. Handling: Protect bathing units during handling and installation to prevent damage. 1.7 WARRANTY A. Provide manufacturer's limited warranty against structural and finish defects for 3 years from date of installation.
LCS26337A75BHG Adaptable 1 of 3
PART 2 PRODUCTS 2.1 MANUFACTURER A. Best Bath Systems, 4545 Enterprise Street, Boise, Idaho 83705, Phone 800-727-9907, Fax 800-627-0929. 2.2 A.D.A. COMPLIANT BATHING UNITS
One piece fiberglass shower stall, meeting A.D.A. and CA. accessibility code criteria. 2.3 MATERIALS A. Gelcoat Finish: Sanitary ware grade gelcoat. Minimum cured thickness 0.015 inch. Barrier Coat: Ceramic fiber filled polyester resin coating to enhance gloss and surface hardness. B. Skin Layer: Glass fiber and polyester resin layer to provide resilient skin against the gelcoat finish. C. Filled and Cored Layer: Fiberglass laminate with minimum 15 percent fiberglass content and filled resin completely
encapsulating a 1/2 inch plywood core on most flat surfaces, to provide stiffness as well as backing for grab bar and seat anchoring. All core termination edges beveled. Floor of ¼ inch thick fiberglass laminate with an integral level support compound bonded to it.
1. Flame Spread Rating: Less than 75 in accordance with ASTM E 162. 2. Smoke Generation: Less than 450 in accordance with NFPA 258. Specifier note: Select plumbing hand. Model LCS26337A75BHG. “Adaptable” The unit measures 63 inches wide x 37-1/2 inches deep x 78-3/4 inches high. [Right][Left] hand plumbing. B. Color: Best Bath White 2.5 ACCESSORIES Specifier Notes: Consult Best Bath Systems for assistance in specifying accessories for specific applications. Coordinate right and left hand accessories with bathing unit models. Select brand of mixing valve and delete the other. A. Mixing Valve: [Symmons S-96-300-B30-L-X-V] Brass, pressure balanced, lever handle valve, plumbing elbow, polished
chrome finish. Hand held shower with applicable hose. Vertically mounted, 30 inch long glide bar, polished chrome finish and cradle with adjustable height setting for hand held shower.
B. Soap Dish: Two (2) white cast polyester surface mounted soap dishes, one (1) each at the sitting level and the standing level. C. Grab Bar 32” x 36” corner type, 1-1/4 inch diameter, stainless steel, 18 gauge. D. Shower Curtain Rod: 65 inches, stainless steel, 20 gauge, 1 inch OD, with mounting flanges. E. Drain: No-Caulk, brass body with polished stainless steel screen. F. Water Stopper kit, collapsible 60 inch grey “T” shaped retainer with large radius end caps. G. Corrugated cardboard interior bottom protector. H. Shower system individually palletized, faced at the opening with corrugated protector and stretch wrapped.
LCS26337A75BHG Adaptable 2 of 3
PART 3 EXECUTION 3.1 EXAMINATION A. Inspect areas where ADA compliant bathing units will be installed. Notify the Architect of conditions that would adversely
affect the installation or subsequent utilization of bathing units. Do not proceed with installation until unsatisfactory conditions are corrected.
3.2 INSTALLATION A. Install in accordance with manufacturer's instructions which are different from those of conventional one piece shower units
in that the unit may be installed directly on top of the flooring and still meet the A.D.A. 1/2 inch maximum curb height requirement. To allow for this the following needs to be done:
1. The hole around the drain needs to be 8 inch diameter. 2. The unit needs to be adhered to the floor using an epoxy adhesive that is provided by the shower manufacturer. 3. Flooring needs to be brought up to the bevel on the curb.
B. Install barrier free bathing units level, plumb, and square with flat wall surfaces. C. Touch-up minor damaged surfaces caused during installation. Replace damaged components as directed by Architect. 3.3 ADJUSTING A. Test and adjust mixing valves and hand held showers for proper and efficient operation, including water temperature,
pressure, and volume. 3.4 CLEANING A. Clean surfaces in accordance with manufacturer's instructions. B. Do not use abrasive cleaners, metal scrapers, or wire brushes. 3.5 SCHEDULE Specifier Notes: Provide a schedule if two or more ADA compliant bathing units are specified with different model numbers or accessories. Identify each unit separately. Coordinate schedule with location of units indicated on drawings. This is an optional location for the schedule, rather than on the drawings. END OF SECTION APPROVED ARCHITECT: NAME: TITLE: DATE: ENGINEER: NAME: TITLE: DATE: OWNER: NAME: TITLE: DATE:
LCS26337A75BHG Adaptable 3 of 3