Upload
doanngoc
View
219
Download
1
Embed Size (px)
Citation preview
MIC3203/MIC3203-1 High-Brightness LED Driver Controller
with High-Side Current Sense
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
General Description The MIC3203 is a hysteretic, step-down, constant-current, High-Brightness LED (HB LED) driver. It provides an ideal solution for interior/exterior lighting, architectural and ambient lighting, LED bulbs, and other general illumination applications. The MIC3203 is well suited for lighting applications requiring a wide-input voltage range. The hysteretic control gives good supply rejection and fast response during load transients and PWM dimming. The high-side current sensing and on-chip current-sense amplifier delivers LED current with ±5% accuracy. An external high-side current-sense resistor is used to set the output current. The MIC3203 offers a dedicated PWM input (DIM) which enables a wide range of pulsed dimming. A high-frequency switching operation up to 1.5MHz allows the use of smaller external components minimizing space and cost. The MIC3203 offers frequency dither feature for EMI control. The MIC3203 operates over a junction temperature from −40°C to +125°C and is available in an 8-pin SOIC package. A dither disabled version MIC3203-1 is also available in the same package as the MIC3203. Datasheets and support documentation can be found on Micrel’s web site at: www.micrel.com.
Features • 4.5V to 42V input voltage range • High efficiency (>90%) • ±5% LED current accuracy • MIC3203: Dither enabled for low EMI • MIC3203-1: Dither disabled • High-side current sense • Dedicated dimming control input • Hysteretic control (no compensation!) • Up to 1.5MHz switching frequency • Adjustable constant LED current • Over-temperature protection • −40°C to +125°C junction temperature range
Applications • Architectural, industrial, and ambient lighting • LED bulbs • Indicators and emergency lighting • Street lighting • Channel letters • 12V lighting systems (MR-16 bulbs, under-cabinet
lighting, garden/pathway lighting) _________________________________________________________________________________________________________________________
Typical Application
MIC3203 Step-down LED Driver
March 2010 M9999-032910-A
Micrel, Inc. MIC3203
March 2010 2 M9999-032910-A
Ordering Information (1) Part Number Marking Junction Temperature Range Package PWM MIC3203YM MIC3203YM −40°C to +125°C 8-Pin SOIC Dither
MIC3203-1YM MIC3203-1YM −40°C to +125°C 8-Pin SOIC Non-Dither
Note: 1. YM® is a GREEN RoHS compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free.
Pin Configuration
8-Pin SOIC MIC3203/MIC3203-1
Pin Description Pin Number Pin Name Pin Function
1 VCC
Voltage Regulator Output. The VCC pin supplies the power to the internal circuitry. The VCC in the output of a linear regulator which is powered from VIN. A 1µF ceramic capacitor is recommended for bypassing and should be placed as close as possible to the VCC and AGND pins. Do not connect to an external load.
2 CS Current-Sense Input. The CS pin provides the high-side current sense to set the LED current with an external sense resistor.
3 VIN
Input Power Supply. VIN is the input supply pin to the internal circuitry and the positive input to the current sense comparator. Due to the high frequency switching noise, a 10µF ceramic capacitor is recommended to be placed as close as possible to VIN and the power ground (PGND) pin for bypassing. Please refer to layout recommendations.
4 AGND Ground pin for analog circuitry. Internal signal ground for all low power sections.
5 EN
Enable Input. The EN pin provides a logic level control of the output and the voltage has to be 2.0V or higher to enable the current regulator. The output stage is gated by the DIM pin. When the EN pin is pulled low, the regulator goes to off state and the supply current of the device is greatly reduced (below 1µA). In the off state, during this period the output drive is placed in a "tri-stated" condition, where MOSFET is in an “off” or non-conducting state. Do not drive the EN pin above the supply voltage.
6 DIM PWM Dimming Input. The DIM pin provides the control for brightness of the LED. A PWM input can be used to control the brightness of LED. DIM high enables the output and its voltage has to be at least 2.0V or higher. DIM low disables the output, regardless of EN “high” state.
7 PGND Power Ground Pin for Power FET. Power Ground (PGND) is for the high-current switching with hysteretic mode. The current loop for the power ground should be as small as possible and separate from the Analog ground (AGND) loop. Refer to the layout considerations for more details.
8 DRV
Gate-Drive Output. Connect to the gate of an external N-channel MOSFET. The drain of the external MOSFET connects directly to the inductor and provides the switching current necessary to operate in hysteretic mode. Due to the high frequency switching and high voltage associated with this pin, the switch node should be routed away from sensitive nodes.
Micrel, Inc. MIC3203
March 2010 3 M9999-032910-A
Absolute Maximum Ratings (1) VIN to PGND .................................................. −0.3V to +45V VCC to PGND ................................................ −0.3V to +6.0V CS to PGND........................................−0.3V to (VIN + 0.3V) EN to AGND........................................−0.3V to (VIN + 0.3V) DIM to AGND ......................................−0.3V to (VIN + 0.3V) DRV to PGND ....................................−0.3V to (VCC + 0.3V) PGND to AGND .......................................... −0.3V to + 0.3V Junction Temperature ................................................ 150°C Storage Temperature Range ....................−60°C to +150°C Lead Temperature (Soldering, 10sec) ....................... 260°C ESD Ratings (3)
HBM......................................................................1.5kV MM.........................................................................200V
Operating Ratings (2) Supply Voltage (VIN).......................................... 4.5V to 42V Enable Voltage (VEN) .............................................. 0V to VIN Dimming Voltage (VDIM).................................................................0V to VIN Junction Temperature (TJ) ........................−40°C to +125°C Junction Thermal Resistance SOIC (θJA) .......................................................98.9°C/W SOIC (θJC).......................................................48.8°C/W
Electrical Characteristics (4) VIN = VEN = VDIM = 12V; CVCC = 1.0µF; TJ = 25°C, bold values indicate −40°C ≤ TJ ≤ +125°C; unless noted.
Symbol Parameter Condition Min. Typ. Max. Units Input Supply VIN Input Voltage Range (VIN) 4.5 42 V IS Supply Current DRV = open 1 3 mA ISD Shutdown Current VEN = 0V 1 µA UVLO VIN UVLO Threshold VIN rinsing 3.2 4 4.5 V UVLOHYS VIN UVLO Hysteresis 500 mV VCC Supply VCC VCC Output Voltage VIN = 12V, ICC = 10mA 4.5 5 5.5 V Current Limit
201.4 212 222.6 mV VCS(MAX) Current Sense Upper Threshold VCS(MAX ) = VIN − VCS
199 212 225 mV 168 177 186 mV
VCS(MIN) Sense Voltage Threshold Low VCS(MIN ) = VIN − VCS 165 177 189 mV
VCSHYS VCS Hysteresis 35 mV VCS Rising 50 ns
Current Sense Response Time VCS Falling 70 ns
CS Input Current VIN − VCS = 220mV 0.5 10 µA Frequency FMAX Switching Frequency 1.5 MHz Dithering (MIC3203) VDITH VCS Hysteresis Dithering Range(5) ±6 mV FDITHER Frequency Dithering Range(5) % of Switching Frequency ±12 %
Micrel, Inc. MIC3203
March 2010 4 M9999-032910-A
Electrical Characteristics (4) (Continued) VIN = VEN = VDIM = 12V; CVCC = 1.0µF; TJ = 25°C, bold values indicate −40°C ≤ TJ ≤ +125°C; unless noted.
Symbol Parameter Condition Min. Typ. Max. Units Enable Input ENHI EN Logic Level High 2.0 V ENLO EN Logic Level Low 0.4 V
VEN = 12V 60 µA EN Bias Current
VEN = 0V 1 µA
Start-Up Time From EN Pin going high to DRV going high 30 µs
Dimming Input DIMHI DIM Logic Level High 2.0 V DIMLO DIM Logic Level Low 0.4 V
20 50 DIM Bias Current
VDIM = 0V 1 µA
DIM Delay Time From DIM Pin going high to DRV going high 450 ns
FDIM Maximum Dimming Frequency 20 kHz External FET Driver
Pull Up, ISOURCE = 10mA 2 DRV On-Resistance
Pull Down, ISINK = -10mA 1.5 Ω
Rise Time, CLOAD = 1000pF 13 DRV Transition Time
Fall Time, CLOAD = 1000pF 7 ns
Thermal Protection TLIM Over-Temperature Shutdown TJ Rising 160 TLIMHYS Over-Temperature Shutdown Hysteresis 20
°C
Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF. 4. Specification for packaged product only. 5. Guaranteed by design.
Micrel, Inc. MIC3203
March 2010 5 M9999-032910-A
Typical Characteristics
Efficiency
vs. Input Voltage
60
70
80
90
100
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
EFFI
CIE
NC
Y (%
)
L=150µHILED=1A
4LED6LED
8LED10LED
Efficiency
vs Input Voltage
60
70
80
90
100
0 5 10 15 20 25 30 35 40 45INPUT VOLTAGE (V)
EFFI
CIE
NC
Y (%
)
L=68µHILED=1A
4LED6LED
8LED10LED
Normalized LED Currentsvs. Input Voltage
0.97
0.98
0.99
1
1.01
1.02
1.03
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
NO
RM
ALI
ZED
LED
CU
RR
ENTS
(A)
L=150µHILED=1A
1LED 2LED 4LED 6LED 8LED10LED
Normalized LED Currentsvs Input Voltage
0.97
0.98
0.99
1
1.01
1.02
1.03
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
NO
RM
ALI
ZED
LED
CU
RR
EN
TS (A
)
L=68µHILED=1A
1LED
2LED4LED
6LED 8LED 10LED
Frequency vs. Input Voltage
0
50
100
150
200
250
300
350
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
FREQ
UEN
CY
(kH
z)
L=150µHILED=1A
1LED
2LED
4LED
6LED8LED
10LED
Frequency vs Input Voltage
0
100
200
300
400
500
600
700
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
FREQ
UE
NC
Y (k
Hz)
L = 68µHILED = 1A
1LED
2LED
4LED
6LED 8LED 10LED
Duty Cycle
vs. Input Voltage
0
25
50
75
100
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
DU
TY C
YCLE
(%)
L=150µHILED=1A
1LED
2LED
4LED
6LED
8LED10LED
Duty Cycle vs Input Voltage
0
25
50
75
100
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
DU
TY C
YCLE
(%)
L=68µHILED=1A
1LED
2LED
4LED
6LED
8LED10LED
Supply Currentvs. Input Voltage
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
SU
PPLY
CU
RR
EN
T (m
A)
TA = 25°CILED = 0A
Micrel, Inc. MIC3203
March 2010 6 M9999-032910-A
Typical Characteristics (Continued)
VCC vs. Input Voltage
0.0
1.0
2.0
3.0
4.0
5.0
6.0
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
VCC
(V)
TA = 25°CILED = 0AICC = 0A
Enable Thresholdvs. Input Voltage
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)EN
AB
LE T
HR
ESH
OLD
(V)
TA = 25°CILED = 0AICC = 0A
Current-Sense Voltagevs. Input Voltage
0
50
100
150
200
250
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
CU
RR
ENT-
SEN
SE V
OLT
AG
E (m
V)
VCS_MAXL = 100µHILED = 1A
VCS_MIN
Shutdown Currentvs. Input Voltage
-5
0
5
10
15
20
25
30
35
40
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
SHU
TDO
WN
CU
RR
EN
T (µ
A)
TA = 25°CILED = 0A
Enable Currentvs. Enable Voltage
0
20
40
60
80
100
120
140
160
0 5 10 15 20 25 30 35 40 45
ENABLE VOTLAGE (V)
ENA
BLE
CU
RR
ENT
(µA
)
TA = 25°C
ICC Limitvs. Input Voltage
0
20
40
60
80
100
120
140
160
180
200
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
ICC
LIM
IT (m
A)
TA = 25°CVCC = 4.2VILED = 0A
Supply Currentvs. Temperature
0.0
0.2
0.4
0.6
0.8
1.0
1.2
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
SUPP
LY C
UR
REN
T (m
A)
VIN = 12VILED = 0A
VCCvs. Temperature
0.0
1.0
2.0
3.0
4.0
5.0
6.0
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
VC
C (V
)
VIN = 12VICC = 0A
Enable Threshold vs. Temperature
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
ENA
BLE
TH
RES
HO
LD (V
)
ON
OFF
Micrel, Inc. MIC3203
March 2010 7 M9999-032910-A
Typical Characteristics (Continued)
Shutdown Currentvs. Temperature
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
SH
UTD
OW
N C
UR
REN
T (u
A)
VIN = 12VEN = 0V
Enable Currentvs. Temperature
0
5
10
15
20
25
30
35
40
45
50
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)E
NA
BLE
CU
RR
ENT
(uA
)
VIN = 12VEN = VIN
Current-Sense Voltagevs. Temperature
0
50
100
150
200
250
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
CU
RR
ENT-
SEN
SE V
OLT
AG
E (m
V)
VCS_MIN
∆_VCSILEDILED = 1A
VCS_MAX
Switching Frequencyvs. Temperature
0
20
40
60
80
100
120
140
160
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
SW
ITC
HIN
G F
RE
QU
EN
CY
(kH
z)
VIN = 12V1ILEDILED = 1AL = 100µH
UVLO Threshold vs. Temperature
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
UVL
O T
HR
ESH
OLD
(V)
ON
OFF
Thermal Shutdownvs. Input Voltage
0
20
40
60
80
100
120
140
160
180
0 5 10 15 20 25 30 35 40 45
INPUT VOLTAGE (V)
THER
MA
L SH
UTD
OW
N (°
C)
OFF
ON
Micrel, Inc. MIC3203
Functional Characteristics
March 2010 8 M9999-032410-A
Micrel, Inc. MIC3203
Functional Characteristics (Continued)
March 2010 9 M9999-032410-A
Micrel, Inc. MIC3203
March 2010 10 M9999-032910-A
Functional Diagram
Figure 1. MIC3203/MIC3203-1 Block Diagram
Functional Description The MIC3203 is a hysteretic step-down driver which regulates the LED current over wide input voltage range. The device operates from a 4.5V to 42V input MOSFET voltage range and provides up to 0.5A source and 1A sink drive capability. When the input voltage reaches 4.5V, the internal 5V VCC is regulated and the DRV pin is pulled high to turn on an external MOSFET if EN pin and DIM pin are high. The inductor current builds up linearly. When the CS pin voltage hits the VCS(MAX) with respect to VIN, the MOSFET turns off and the Schottky diode takes over and returns the current to VIN. Then the current through inductor and LEDs starts decreasing. When CS pin hits VCS(MIN), the MOSFET turns on and the cycle repeats.
The frequency of operation depends upon input voltage, total LEDs voltage drop, LED current and temperature. The calculation for frequency of operation is given in application section. The MIC3203 has an on board 5V regulator which is for internal use only. Connect a 1µF capacitor on VCC pin to analog ground. The MIC3203 has an EN pin which gives the flexibility to enable and disable the output with logic high and low signals. The MIC3203 also has a DIM pin which can turn on and off the LEDs if EN is in HIGH state. This DIM pin controls the brightness of the LED by varying the duty cycle of DIM pin from 1% to 99%.
Micrel, Inc. MIC3203
March 2010 11 M9999-032910-A
Application Information The internal block diagram of the MIC3203 is shown in Figure 1. The MIC3203 is composed of a current-sense comparator, voltage and current reference, 5V regulator and MOSFET driver. Hysteretic mode control – also called bang-bang control – is a topology that does not employ an error amplifier, using an error comparator instead. The inductor current is controlled within a hysteretic window. If the inductor current is too small, the power MOSFET is turned on; if the inductor current is large enough, the power MOSFET is turned off. It is a simple control scheme with no oscillator and no loop compensation. Since the control scheme does not need loop compensation, it makes a design easy, and avoids problems of instability. Transient response to load and line variation is very fast and only depends on propagation delay. This makes the control scheme very popular for certain applications.
LED Current and RCS The main feature in MIC3203 is to control the LED current accurately within ±5% of set current. Choosing a high-side RCS resistor helps for setting constant LED current irrespective of wide input voltage range. The following equation gives the RCS value:
)I
V+V(x
21
=RLED
)MIN(CS)MAX(CSCS
Table 1. RCS for LED Current RCS (Ω) ILED (A) I2R (W) Size (SMD)
1.33 0.15 0.03 0603 0.56 0.35 0.07 0805 0.4 0.5 0.1 0805 0.28 0.7 0.137 0805 0.2 1.0 0.2 1206 0.13 1.5 0.3 1206 0.1 2.0 0.4 2010 0.08 2.5 0.5 2010
0.068 3.0 0.6 2010
For VCS(MAX) and VCS(MIN), refer to the Electrical Characteristic table.
Frequency of Operation To calculate the frequency spread across input supply:
tΔIΔ
L=V LL
L is the inductance, ∆IL is fixed (the value of the hysteresis):
CS
)MIN(CS)MAX(CSL R
VV=IΔ
-
VL is the voltage across inductor L which varies by supply. For current rising (MOSFET is ON):
RISE_L
Lr V
IΔL=t
where: VL_RISE = VIN − ILED × RCS − VLED
For current falling (MOSFET is OFF):
FALL_L
Lf V
IΔL=t
where:
VL_FALL = VD + ILED × RCS + VLED
fr t+t=T , T1
=FSW
)V+V(×IΔ×L)VR×IV(×)V+R×I+V(
=FINDL
LEDCSLEDINLEDCSLEDDSW
--
where : • VD is Schottky diode forward drop • VLED is total LEDs voltage drop • VIN is input voltage • ILED is average LED current
Micrel, Inc. MIC3203
March 2010 12 M9999-032910-A
Inductor According to the above equation, choose the inductor to make the operating frequency no higher than 1.5MHz. The following Tables give a reference inductor value and corresponding frequency for a given LED current. For space-sensitive applications, smaller inductor with higher switching frequency could be used but efficiency of the regular will be reduced.
Table 2. Inductor for VIN = 12V, 1 LED RCS (Ω) ILED (A) L (µH) FSW (kHz)
1.33 0.15 220 474 0.56 0.35 100 439 0.4 0.5 68 461 0.28 0.7 47 467 0.2 1.0 33 475 0.13 1.5 22 463 0.1 2.0 15 522 0.08 2.5 12 522
0.068 3.0 10 533
Table 3. Inductor for VIN = 24V, 4 LEDs RCS (Ω) ILED (A) L (µH) FSW (kHz)
1.33 0.15 470 474 0.56 0.35 220 426 0.4 0.5 150 447
0.28 0.7 100 470 0.2 1.0 68 493
0.13 1.5 47 463 0.1 2.0 33 507
0.08 2.5 27 496 0.068 3.0 22 517
Table 4. Inductor for VIN = 36V, 8 LEDs RCS (Ω) ILED (A) L (µH) FSW (kHz)
1.33 0.15 470 495 0.56 0.35 220 446 0.4 0.5 150 467 0.28 0.7 100 490 0.2 1.0 68 515 0.13 1.5 47 485 0.1 2.0 33 530 0.08 2.5 27 519
0.068 3.0 22 541
Given an inductor value, the size of the inductor can be determined by its RMS and peak current rating.
18.0=V+VVV
×2=IIΔ
)MIN(CS)MAX(CS
)MIN(CS)MAX(CS
L
L -
L2L
2L)RMS(L I≈IΔ
121
+I=I
LLL)PK(L I09.1=IΔ21
+I=I
where: IL is inductor average current. Select an inductor with saturation current rating at least 30% higher than the peak current.
MOSFET MOSFET selection depends upon the maximum input voltage, output LED current and switching frequency. The selected MOSFET should have 30% margin on maximum voltage rating for high reliability requirements. The MOSFET channel resistance RDSON is selected such that it helps to get the required efficiency at the required LED currents as well as meets the cost requirement. Logic level MOSFETs are preferred as the drive voltage is limited to 5V. The MOSFET power loss has to be calculated for proper operation. The power loss consists of conduction loss and switching loss. The conduction loss can be found by:
IN
LED_TOTAL
LED)FET(RMS
DSON2
)FET(RMS)CON(LOSS
VV
=D
D×I=I
R×I=P
Micrel, Inc. MIC3203
March 2010 13 M9999-032910-A
The switching loss occurs during the MOSFET turn-on and turn-off transition and can be found by:
GATE
DRVDRV
gd2gsDRV
SWLEDIN)TRAN(LOSS
RV
=I
)Q+Q(×I
F×I×V=P
where: RGATE is total MOSFET resistance, Qgs2 and Qgd can be found in a MOSFET manufacturer datasheet. The total power loss is:
)TRAN(LOSS)CON(LOSS)TOT(LOSS P+P=P
The MOSFET junction temperature is given by:
AJAθ)TOT(LOSSJ T+R×P=T
The TJ must not exceed maximum junction temperature under any conditions.
Freewheeling Diode The free wheeling diode should have the reverse voltage rating to accommodate the maximum input voltage. The forward voltage drop should be small to get the lowest conduction dissipation for high efficiency. The forward current rating has to be at least equal to LED current. A Schottky diode is recommended for highest efficiency.
Input Capacitor The ceramic input capacitor is selected by voltage rating and ripple current rating. To determine the input current ripple rating, the RMS value of the input capacitor can be found by:
D)-(1DLEDCIN(RMS) II ××=
The power loss in the input capacitor is:
ESRINCIN(RMS)2
LOSS(CIN) C I P ×=
The input capacitor current rating can be considered as ILED/2 under the worst condition D = 50%.
LED Ripple Current The LED current is the same as inductor current. If LED ripple current needs to be reduced then place a 4.7µF/50V ceramic capacitor across LED.
Frequency Dithering The MIC3203 is designed to reduce EMI by dithering the switching frequency ±12% in order to spread the frequency spectrum over a wider range. This lowers the EMI noise peaks generated by the switching regulator. Switching regulators generate noise by their nature and they are the main EMI source to interference with nearby circuits. If the switching frequency of a regulator is modulated via frequency dithering, the energy of the EMI is spread among many frequencies instead of concentrated at fundamental switching frequency and its harmonics. The MIC3203 modulates the VCS(MAX) with amplitude ±6mV by a pseudo random generator to generate the ±12% of the switching frequency dithering to reduce the EMI noise peaks.
Micrel, Inc. MIC3203
March 2010 14 M9999-032910-A
PCB Layout Guidelines Warning!!! To minimize EMI and output noise, follow these layout recommendations. PCB Layout is critical to achieve reliable, stable and efficient performance. A ground plane is required to control EMI and minimize the inductance in power, signal and return paths. The following guidelines should be followed to insure proper operation of the MIC3203 regulator.
IC Use thick traces to route the input and output power lines. Signal and power grounds should be kept separate and connected at only one location.
Input Capacitor Place the input capacitors on the same side of the board and as close to the IC as possible. Keep both the VIN and PGND traces as short as possible. Place several vias to the ground plane close to the input capacitor ground terminal, but not between the input capacitors and IC pins. Use either X7R or X5R dielectric input capacitors. Do not use Y5V or Z5U type capacitors. Do not replace the ceramic input capacitor with any other type of capacitor. Any type of capacitor can be placed in parallel with the input capacitor. If a Tantalum input capacitor is placed in parallel with the input capacitor, it must be recommended for switching regulator applications and the operating voltage must be derated by 50%. In “Hot-Plug” applications, a Tantalum or Electrolytic bypass capacitor must be placed in parallel to ceramic capacitor to limit the over-voltage spike seen on the input supply with power is suddenly applied. In this case an additional Tantalum or Electrolytic bypass input capacitor of 22µF or higher is required at the input power connection if necessary.
Inductor Keep the inductor connection to the switch node (MOSFET drain) short. Do not route any digital lines underneath or close to the inductor. To minimize noise, place a ground plane underneath the inductor.
Output Capacitor If LED ripple current needs to be reduced then place a 4.7µF/50V capacitor across LED. The capacitor must be
placed as close to the LED as possible.
MOSFET Place the MOSTET as close as possible to the MIC3203 to avoid the trace inductance. Provide sufficient copper area on MOSFET ground to dissipate the heat.
Diode Place the Schottky diode on the same side of the board as the IC and input capacitor. The connection from the Schottky diode’s Anode to the switching node must be as short as possible. The diode’s Cathode connection to the RCS must be keep as short as possible.
RC Snubber If a RC snubber is needed, place the RC snubber on the same side of the board and as close to the Schottky diode as possible.
RCS (Current-Sense Resistor) VIN pin and CS pin must be as close as possible to RCS. Make a Kelvin connection to the VIN and CS pin respectively for current sensing.
Trace Routing Recommendation Keep the power traces as short and wide as possible. One current flowing loop is during the MOSFET ON time, the traces connecting the input capacitor CIN, RCS, LEDs, Inductor, the MOSFET and back to CIN. The other current flowing loop is during the MOSFET OFF time, the traces connecting RCS, LED, inductor, free wheeling diode and back to RCS. These two loop areas should kept as small as possible to minimize the noise interference, Keep all analog signal traces away from the switching node and its connecting traces.
Micrel, Inc. MIC3203
March 2010 15 M9999-032910-A
Ripple Measurements To properly measure ripple on either input or output of a switching regulator, a proper ring in tip measurement is required. Standard oscilloscope probes come with a grounding clip, or a long wire with an alligator clip. Unfortunately, for high-frequency measurements, this ground clip can pick-up high-frequency noise and erroneously inject it into the measured output ripple. The standard evaluation board accommodates a home made version by providing probe points for both the input and output supplies and their respective grounds. This requires the removing of the oscilloscope probe sheath and ground clip from a standard oscilloscope probe and wrapping a non-shielded bus wire around the oscilloscope probe. If there does not happen to be any non-shielded bus wire immediately available, the leads from axial resistors will work. By maintaining the shortest possible ground lengths on the oscilloscope probe, true ripple measurements can be obtained.
Figure 2. Low Noise Measurement
Micrel, Inc. MIC3203
March 2010 16 M9999-032910-A
Evaluation Board Schematic
Micrel, Inc. MIC3203
March 2010 17 M9999-032910-A
Bill of Materials Item Part Number Manufacturer Description Qty.
12105C475KAZ2A AVX(1) C1, C5
GRM32ER71H475KA88L Murata(2) 4.7µF/50V, Ceramic Capacitor, X7R, Size 1210 2
12105C475KAZ2A AVX(1) GRM32ER71H475KA88L Murata(2) C2
C3225X7S1H475M TDK(3)
4.7µF/50V, Ceramic Capacitor, X5R, Size 1210 1
08053D105KAT2A AVX(1) 1µF/25V, Ceramic Capacitor, X5R, Size 0805 1 GRM21BR71E105KA99L Murata(2) C3
C2012X7R1E105K TDK(3) 1µF/25V, Ceramic Capacitor, X7R, Size 0805 1
(Open) 08055A271JAT2A AVX(1) C4
(Open) GRM2165C2A271JA01D Murata(2) 270pF/50V, Ceramic Capacitor NPO, Size 0805 1
SK36-TP MCC(4) SK36 Fairchild(5) D1
SK36-7-F Diodes, Inc.(6)
60V, 3A, SMC, Schottky Diode 1
L1 SLF10145T-680M1R2 TDK(3) 68µH, 1.2A, 0.14Ω, SMT, Power Inductor 1 M1 FDS5672 Fairchild(7) MOSFET, N-CH, 60V, 12A, SO-8 1
R1 CSR 1/2 0.2 1% I Stackpole Electronics, Inc(8) 0.2Ω Resistor, 1/2W, 1%, Size 1206 1
R2, R3 CRCW08051003FKEA Vishay(9) 100kΩ Resistor, 1% , Size 0805 2 R4 CRCW08050000FKEA Vishay(9) 0Ω Resistor, 1%, Size 0805 1 R5 (Open) CRCW08052R20FKEA Vishay(9) 2.2Ω Resistor, 1%, Size 0805 1 R6 CRCW08051002FKEA Vishay(9) 10kΩ Resistor, 1% , Size 0805 1
U1 MIC3203YM Micrel, Inc.(10) High Brightness LED Driver Controller with High-Side Current Sense 1
Notes: 1. AVX: www.avx.com. 2. Murata: www.murata.com. 3. TDK: www.tdk.com. 4. MCC: www.mccsemi.com. 5. Fairchild: www.fairchildsemi.com. 6. Diodes Inc. : www.diodes.com. 7. Fairchild : www.Fairchildsemi.com. 8. Stackpole Electronics: www.seielect.com. 9. Vishay: www.vishay.com. 10. Diodes Inc. : www.diodes.com. 11. Micrel, Inc.: www.micrel.com.
Micrel, Inc. MIC3203
March 2010 18 M9999-032910-A
PCB Layout Recommendation
Top Assembly
Top Layer
Micrel, Inc. MIC3203
March 2010 19 M9999-032910-A
PCB Layout Recommendation (Continued)
Bottom Layer
Micrel, Inc. MIC3203
March 2010 20 M9999-032910-A
Package Information
8-Pin SOIC
Micrel, Inc. MIC3203
March 2010 21 M9999-032910-A
Recommended Landing Pattern
8-Pin SOIC
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use.
Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s
use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale.
© 2010 Micrel, Incorporated.