Embed Size (px)
Citation preview
High School of Dundee
Technology Technology
DepartmentDepartment
Gra
phic
G
raphic
C
om
munic
ati
on
Com
mu
nic
ati
on
Cut cone
The given views show the Front Elevation and part Plan of a cut cone.
Draw the following views :-
Complete PlanEnd ElevationDevelopmentTrue Shape of cut
Technology Department Technology Department
Finding position of End Elevation
Technology Department Technology Department
Start drawing the End Elevation by projecting the height and width from the given views.
Drawing Generators on Plan
Use 30o and 60o lines to divide the Plan into 12 equal parts. 1
2
3
4
567
8
9
10
1211
Number each of the points on the Plan.
Technology Department Technology Department
Transfer Generators from Plan to Elevation
Project each of the points from the Plan onto the Elevation base.
1 2345678
910 11 12
1
2
3
4
567
8
9
10
1211
Number each of the points on the Elevation making sure that the numbers correspond with those on the Plan.
Technology Department Technology Department
Drawing generator on Elevation
Draw generators from the apex of the cone to each of the points found on the base of the cone.
1 2345678
910 11 12
Technology Department Technology Department
Drawing generators onto End Elevation
1211
10
9
8
76 5
4
3
2
1
9108
117
126
15
243
Project the position of the generators onto the End Elevation by projecting the points from the Plan.
6584 3
102
111127 9
Number each of the points on the End Elevation.
Draw generators from the apex to the base.
Technology Department Technology Department
Finding cut points on End Elevation
Project the points where the generators on the Elevation cross the cut onto the End Elevation.
1211
10
9
8
76 5
4
3
2
1
9108
117
126
15
243 65
84 3
102
111127 9
Mark each of the points found with a small dot.
Technology Department Technology Department
Completing End Elevation
Complete the End Elevation by drawing a smooth curve through each of the point and then darkening the other outlines on the view.
9108
117
126
15
243 65
84 3
102
111127 9
Technology Department Technology Department
Finding cut points on Plan
Project the points from the cut on the Elevation up to the correct generator lines on the Plan.
(Note that points 6 and 12 will not be able to be found at this time.)
9108
117
126
15
243 65
84 3
102
111127 9
Mark each of the points found with a small dot
Technology Department Technology Department
Finding points 6 and 12 on Plan (alternative 1)
Project point 6 and 12 onto the outside generator on the Elevation.
Project this point up to the centre line of the Plan.
Use compasses to rotate this point onto the correct generators for points 6 and 12.
Mark each of these points with a small dot
Technology Department Technology Department
Finding points 6 and 12 on Plan (alternative 2)
Project points 6 and 12 from the End Elevation onto the correct generators on the Plan.
Technology Department Technology Department
Completing Plan
To complete the Plan draw a smooth curve through each of the 12 points found.
Technology Department Technology Department
Development of surface (1)
Mark the position where the apex of the Development will be placed.
9 87
6
5
4
3
2
1
12
11
9
10Draw the first generator.
Draw the base line of the Development.
Step off the size to each generator point along the base.
Number each of the points found.
Draw generator lines from the apex to each of the points on the base.
Technology Department Technology Department
Development of surface (2)
Mark each of the found points with a small dot.
It is necessary to find the ‘true length’ of the cut points along each generator.
To find these sizes project a line through each point on the cut of the Elevation to the outside generator.
Technology Department Technology Department
Development of surface (3)
Measure the distance from the apex to each point on the outside generator.
Transfer this size to the correct generator on the Development.
Mark each point with a small dot.
Draw a smooth curve through each point found.
Darken each of the other outlines on the Development.
Technology Department Technology Department
True Shape of cut (1)
Project each of the points on the cut of the Elevation away at right angles to the cut surface.
Draw a datum line on the True Shape – in this case the centre line has been chosen.
Number each of the lines projected up to the True Shape.
Technology Department Technology Department
True Shape of cut (2)
Measure the sizes from the cut points to the centre line on the Plan and transfer each of these sizes to the correct lines on the True Shape.
Note – These sizes can also be measured from the End Elevation.
Mark each of the points with a small dot.
Technology Department Technology Department
True Shape of cut (3)
To finish the True Shape draw a smooth curve through each of the points found.
The final drawing should look like this.
