Upload
others
View
7
Download
0
Embed Size (px)
Citation preview
MK-99COM080-00
Hitachi Compute Blade Embedded Fibre Channel Switch Module License Installation Manual Fabric Watch License GVX-BE2FSL3X1 GGX-BE3FSL3X1 GV-BE2FSL3X1-Y
FASTFIND LINKS
Getting Help
Contents
2
Important Notes
No part of this manual may be reproduced or transmitted without permission of Hitachi, Ltd.
Information in this manual might be changed without a previous notice.
Every effort has been made in the preparation of this manual to ensure accuracy of the
contents, but this manual may contain errors or inaccurate materials. We welcome any
comments or suggestions on this manual for future improvement.
Hitachi assumes no responsibility for any damage resulting from use of the product which does
not comply with the instructions provided in this manual.
Trademarks and Registered Trademarks
Product and company names used in this manual may be trademarks or registered trademarks of their
respective owners.
Copyright
All contents of this manual are protected under copyright law. No part of this manual may be
reproduced or transmitted without permission of Hitachi, Ltd.
Copyright© Hitachi, Ltd. 2013 All rights reserved.
3
Introduction
This license package is for the Hitachi 8Gbps Embedded Fibre
Channel Switch. This manual provides the information
necessary to install the Fabric Watch license.
Notation
Symbols used in this manual
The symbols used in this manual are as follows:
: Indicates that failure to follow the instruction may cause a system down.
:
Indicates an instruction to be followed to successfully update the license.
Warning
Caution
4
Table of Contents
Important Notes ............................................................................................................... 2 Trademarks and Registered Trademarks..................................................................... 2 Copyright .......................................................................................................................... 2 Notation ............................................................................................................................ 3
1 Before Use .......................................................................... 6 1. Purpose ......................................................................................................................... 6 2. Check the Package Contents.................................................................................. 6 Requirements for Use of Fabric Watch ........................................................................ 7
2 Preparations ........................................................................ 8 1. Supplied Items ............................................................................................................. 8 2. User Preparations......................................................................................................... 9 3.Connecting ................................................................................................................. 11
3 Preconfirmation ................................................................. 15 1. Check the System Status ......................................................................................... 15 2. Confirm the Fibre Channel Switch's WWN ............................................................ 17
4 User Registration ............................................................... 19 1. User Registration ........................................................................................................ 19
5 Log in to the Web site ........................................................ 31 1. Customer Log in (Log in to MyBrocade) ........................................................ 31 2. Enter the Software Portal ......................................................................................... 33 3. Obtain the License Key ............................................................................................ 35
6 Install the License .............................................................. 38 1. Check Compute Blade Status ................................................................................ 38 2. Install the License ...................................................................................................... 38 3. Stick the Nameplate ................................................................................................. 39
7 Download Recommended Configuration Information ....... 40 1. Check Compute Blade Status ................................................................................ 40 2. Install the IIS FTP Server ............................................................................................. 40 3. Download Recommended Configuration Information .................................. 54
5
8 Completion Steps ............................................................. 56
9 Troubleshooting ................................................................ 57
6
1 Before Use
This chapter provides what you should know before you begin to
install the Fabric Watch license for a Hitachi 8Gbps Embedded Fibre
Channel Switch module.
1. Purpose
This manual describes how to install the Fabric Watch license for the Hitachi Compute Blade
8Gbps Embedded Fibre Channel Switch module. Before using the 8Gbps Embedded Fibre
Channel Switch module, please also read the following manuals:
In addition, the referred manual is different depend on the system unit that installed the 8Gbps
Embedded Fibre Channel Switch module.
(1) CB2000
Compute Blade 2000 User's Guide
Manuals in Compute Blade Fibre Channel Switch Accessory CD (EN)
(2) CB500
Compute Blade 500 Series Getting Started Guide
Compute Blade 500 Series Switch Module Setup Guide
Compute Blade 500 Series Management Module Setup Guide
Compute Blade 500 Series Web Console Setup Guide
Compute Blade 500 Series CLI Console Setup Guide
Manuals in Compute Blade Fibre Channel Switch Accessory CD (EN)
2. Check the Package Contents
Check the following to ensure that you have received exactly what you ordered. If you have not
received what you ordered, please contact your dealer where you purchased the package from.
The package part number indicates exactly what you ordered.
You have all the items shown in the Package Contents list.
If the package contains an additional instruction sheet, please be sure to read the sheet.
7
Requirements for Use of Fabric Watch
To use the Fabric Watch feature, you need to:
(1) Install a Fabric Watch license.
(2) Download a configuration file (containing the Hitachi recommended configuration
information).
This manual describes (1) how to install the Fabric Watch license and (2) how to download a
configuration file (containing the Hitachi recommended configuration information).
8
2 Preparations
This chapter provides information on what you need to have in order
to install the Fabric Watch license for an 8Gbps Embedded Fibre
Channel Switch module and describes how to make connections.
1. Supplied Items
Software License Package
Transaction key form
License sticker Embedded Fibre Channel
Switch Module License
Installation Manual
(this manual)
Hitachi Compute Blade
Embedded Fibre Channel
Switch Module
License Insta llation Manual
Fabric Watch License
"Compute Blade Fibre Channel Switch Accessory CD (EN)" This CD is supplied with Embedded Fibre Channel Switch equipment.
Software License Package
Do No t Di scard ! Lice n se E n close d!
Fabric Watch
9
2. User Preparations
This section provides information on what you need to have in order to install the Fabric Watch
license.
(1) Hardware/software requirements for license key acquisition
The following table shows the hardware/software necessary to obtain a license to be installed in the
Fibre Channel Switch.
Item Requirements
One PC
Internet access(*1)
Web browser
(*1) You need to set up access to Internet.
10
(2) Hardware/software requirements for Fibre Channel Switch connection
The following table shows the hardware/software necessary to connect to the 8Gbps Fibre Channel
Switch module where the license is to be installed and operate the switch via its commands.
Item Requirements
One PC (*1) LAN connectivity
telnet tool
(such as Tera Term or HyperTerminal)
One LAN cable (cross cable(*2)) (*1) Category 5
(*1) If you already have a PC connected to the 8Gbps Embedded Fibre Channel Switch module
through LAN (for purposes such as management), you can use the existing configuration.
(*2) If you have no cross LAN cable, prepare two straight cables and HUB when connecting to LAN
port of Fibre Channel Switch module.
11
3.Connecting
(1) CB2000
Connecting to the embedded Fibre Channel Switch module through LAN depends on the Switch
module network setting. You can confirm the Switch module setting by using the LC command, a
system console command of the Management module.
①Case that “Ext” status in the Switch module setting screen shows “Int” indicated by selecting
"SW" in the LC command of management module. This setting is the default at shipment.
②Case that “Ext” status in the Switch module setting screen shows “Ext” indicated by selecting
"SW" in the LC command of management module.
The screen copy bellow shows the sample of the Switch module network setting.
Connect a LAN cable to the LAN interface connector for the system console at the MGMT0
port of the Management module. When two Management modules are installed, connect the
LAN cable to the one with the MSR LED that lights solid green.
System console terminal
LAN cable
-- Switch module network setting --
SW Ext IP address Subnetmask Default gateway Ext port Synchronize
-- ---- ---------------- --------------- --------------- -------- -----------
0 Ext 0. 0. 0. 0 0. 0. 0. 0 0. 0. 0. 0 MGMT-0 No
1 Ext 0. 0. 0. 0 0. 0. 0. 0 0. 0. 0. 0 MGMT-0 No
2 Int ------------- ------------- ------------- ------ ---------
3 Int ------------- ------------- ------------- ------ ---------
4 Int ------------- ------------- ------------- ------ ---------
5 Ext 172. 16.102. 52 255.255. 0. 0 0. 0. 0. 0 MGMT-0 Yes
12
③Case that “Ext” status in the Switch module setting screen shows “IOSW” indicated by
selecting "SW" in the LC command of management module.
The screen copy bellow shows the sample of the Switch module network setting.
Connect a LAN cable to the LAN interface connector for the system console at the embedded
Fibre Channel Switch module.
Fibre Channel Switch Fibre Channel Switch
LAN cable
Rear of Compute Blade 2000
Using LAN cross cable Using LAN straight cables
LAN cross cable
LAN straight cable
-- Switch module network setting --
SW Ext IP address Subnetmask Default gateway Ext port Synchronize
-- ---- ---------------- --------------- --------------- -------- -----------
0 Ext 0. 0. 0. 0 0. 0. 0. 0 0. 0. 0. 0 MGMT-0 No
1 Ext 0. 0. 0. 0 0. 0. 0. 0 0. 0. 0. 0 MGMT-0 No
2 Int ------------- ------------- ------------- ------ ---------
3 Int ------------- ------------- ------------- ------ ---------
4 Int ------------- ------------- ------------- ------ ---------
5 IOSW 192.168. 0.101 255.255.255. 0 0. 0. 0. 0 MGMT-0 No
13
(2) CB500
There are the following two ways for connecting to the embedded Fibre Channel Switch module
through LAN.
① Connects via the LAN interface connector at the management module
② Connects via the LAN interface connector at the embedded Fibre Channel Switch module
You can confirm the Switch module setting through the web console or CLI console.
See the following manuals for details of how to confirm and how to set.
■Compute Blade 500 Series Web Console Setup Guide
■Compute Blade 500 Series CLI Console Setup Guide
① Connects via the LAN interface connector at the management module
Connect a LAN cable to the LAN interface connector for the system console at the MGMT0 port of
the Management module. When two Management modules are installed, connect the LAN cable to
the one with the MSR LED that lights solid green.
System console terminal
LAN cable
MSR
14
② Connects via the LAN interface connector at the embedded Fibre Channel Switch module
Connect a LAN cable to the LAN interface connector for the system console at the embedded Fibre
Channel Switch module.
System console terminal
LAN cable
LAN cable
SFP
SFP
SFP
SFP
SFP
SFP
Management module
LAN cross cable
LAN straight cable
Using LAN cross cable
Using LAN straight cables
Management module
15
3 Preconfirmation
This chapter describes a set of procedures to check the status of the
Compute Blade with at least one 8Gbps Embedded Fibre Channel
Switch module before installing the Fabric Watch license.
1. Check the System Status
Check the status of the Compute Blade with at least one 8Gbps Embedded Fibre Channel Switch
module.
(1) Checking Compute Blade power status
Check the Power LED (PWR) to see the power status of the Compute Blade
■ Green: Indicates that the main power is turned on.
Go to the next step, (2) Checking server operation status.
■ Amber: Indicates that the system is in standby state.
Go to the next step, (2) Checking server operation status.
■ Off: Indicates that the Compute Blade does not receive power.
First, connect the Compute Blade to AC power and close its circuit breaker to turn
it into standby state. Then, go to the next step, (2) Checking server operation
status.
Power LED(PWR)
Compute Blade 500
Compute Blade 2000
16
(2) Checking server operation status
If the Fibre Channel Switch is operating during installing the Fabric Watch license according to this
manual, the communication lines of the Switch may be confused. Therefore, it is strongly
recommended that all the Compute Blade servers be stopped and in standby state before installing
the license.
Use the following flowchart to check the operation status and configuration of the servers.
Can all Compute Blade servers be stopped?
Yes
START
No
Have servers connected to embedded fibre channels all stopped?
Yes
No
Do servers connected to embedded fibre channels have alternate fiber channel paths?
Yes
No
Stop all servers and go to
Section 2 (Confirm the Fibre Channel Switch's
WWN).
You can proceed to license installation.
Go to Section 2 (Confirm the Fibre Channel
Switch's WWN).
Enable path to Fiber Channel Switch where
license is not to be installed, and switch paths.
Once paths have been successfully switched,
go to Section 2 (Confirm the Fibre Channel
Switch's WWN).
With this configuration, you need to stop all servers to proceed to license installation. Wait until all servers can be stopped.
If the Fibre Channel Switch is operating during installing the Fabric Watch license, the
communication lines of the Switch may be confused. This may result in loss of connection
to servers or devices (such as servers and disks), which may cause system down.
If you install a Fabric Watch license and download configuration information while servers
are operating, be sure to follow the steps shown below.
Warning
17
2. Confirm the Fibre Channel Switch's WWN
(1) Use a LAN cable to connect either the primary-side Management module or LAN
interface connector of Fibre Channel Switch module with the PC (for connection to the
8Gbps Embedded Fibre Channel Switch module).
(For more information on the connection, see (2) Hardware/software requirements for
Management module connection in Section 2, "User Preparations" of Chapter 2.)
(2) Check that the Fibre Channel Switch is up and running. Telnet to the switch and login as
an administrator (admin) with the appropriate user ID and password.
* For information on the user registration for the Fibre Channel Switch, see "Compute
Blade Fibre Channel Switch User's Guide."
(3) Enter the licenseshow command to check that no Fabric Watch license has been
installed.
switch:admin> licenseshow ← Enter licenseshow command
S9Rz9beQRyTAS0AT:
Fabric license
dQ9dzzScQeRAe0A:
Extended Fabric license
RyceSQ9SzzUzdfTK:
Fabric Watch license
RyceSQ9SzzWzdfTM:
Performance Monitor license
switch:admin>
Fabric OS (SW5460)
switch login: xxxxx ← Enter User ID of administrator (admin). Password: xxxxx ← Enter Password.
switch:admin>
Check that there is no "Fabric Watch license" line.
18
(4) Enter the switchshow command to obtain and write down the WWN of the Fibre Channel
Switch in the blank area labeled "Write down here" below.
Write down the WWN of the Fibre Channel Switch where the license is to be installed.
Write down here.
The WWN of the Fibre Channel Switch is necessary to obtain the license.
Since each license only covers a single Fibre Channel Switch (or WWN), if the wrong WWN is
used to obtain a license, the license may not be installed in the appropriate Fiber Channel
Switch.
Be sure to check that the WWN of the Fibre Channel Switch is correct.
(5) Use the exit command to terminate the telnet session. Go to Chapter 4, "Obtain the
License Key."。
switch:admin> switchshow ← Enter switchshow command
switchName: switch
switchType: 87.1
switchState: Online
switchMode: Native
switchRole: Principal
switchDomain: 1
switchId: fffc01
switchWwn: 10:00:00:05:1e:a2:00:1b ← Write down the value of WWN
zoning: OFF
switchBeacon: OFF
Area Port Media Speed State Proto
=====================================
0 0 id N8 No_Light
<Omitted>
Caution
19
4 User Registration
This chapter describes how to create and configure a user account
necessary to access the Web site for obtaining a license key.
It is not necessary to create a user account newly if you create a user account once.
1. User Registration
(1) Set up the PC so that it has access to Internet. Open the Web browser and go to the
URL shown below. The Brocade Web site appears.
http://www.brocade.com
The screen on the Brocade Web site might be changed without a previous notice.
(2) On the Brocade Web site screen, click Customer Log In.
Click “Customer Log In”
Caution
Caution
20
(3) On the “Brocade Connect is Now MyBrocade” screen, click Log in to MyBrocade.
(4) On the “Welcome to Brocade login” screen, click register now.
Click “Register now”
Click “Log in to MyBrocade”
21
(5) On the “Register with Brocade” screen, fill the required fields and click Continue.
Click “CONTINUE”
Enter your company E-mail address. (Note: Your company email address will be your USER ID.) Your active company Email address is required. Personal Email addresses are not accepted.
Type the word you see in the above image
Select the information or access you
would like to register for
Select “Brocade Customer, Brocade Employee or Other Brocade Enthusiast “
22
(6) On the “Account Information” screen, fill the required fields listed below and click
SUBMIT.
※The information input and the content of the question necessary for the user
account registration are subjected to variation.
Click “SUBMIT”
23
Required fields list
YOUR Salutation Select your salutation
PERSONAL First Name Your first name
DETAILS Last Name Your last name
Company Your company name
JOB Title Your job title
YOUR Industry Select your company’s industry
BUSINESS Number of Employees Select your company’s number of employees
DETAILS Address 1 Your address
City Your city name
Country Select your country
State/Province Your state/province
Zip/Postal Code Your zip/postal code
Phone 1 Your phone number
Fax Your FAX number
YOUR SITE Password Type your password
ACCESS Retype Password Retype your password
DETAILS Type Security Question Type question to receive the re-delivery
when the password is forgotten
ex)Today’s weather?
Type Security Answer Type answer to the Security Question
ex)Fine
(7) Completed registration screen appears, and you will receive an email at the address you
provided at registration time.
∨
∨
24
(8) The following mail is sent to the registered e-mail address. Access URL described in this
mail.
(9) The screen described that you have successfully activated your new account appears.
Click MyBrocade Log in to configure your new account.
Welcome New MyBrocade User
You now have an account on MyBrocade (formerly Brocade Connect). Please perform the
following steps to complete the activation process.
Step 1: To activate, click on the following URL
If the following activation URL is broken into two lines, copy the entire activation
URL (including first and second lines) and paste into your browser window. IMPORTANT
NOTE: MyBrocade is not compatible with browser IE 8. Please browse the site using IE
7 or Firefox.
http://my.brocade.com/wps/portal/activation?rp_activationcode=xxxxxxxxxxxxxxxxxxx
Step 2: Log in using the email address and password you specified registration time:
Your MyBrocade User ID = [email protected]
We appreciate your interest in Brocade, and look forward to providing you with resources
to help you manage your Brocade network. If you have any questions, please contact
Thank You!
Brocade
Access URL described in this mail
Click “MyBrocade Log in”
25
(10) On the “Log in” screen, enter your USER ID (email address you provided) and password,
and click login
(11) According to the procedure of the screen, you have to update your information in your
account. Click My Profile first.
Enter your USER ID and PASSWORD,and click “login”.
Click “My profile”
26
(12) On the “My Profile” screen, click Update Roles(s) and open the “Role(s)” screen. Select
all checkboxes that apply and click SAVE EDITS.
Select all that apply
Click “Update Roles(s)”
Click “SAVE EDITS”
27
(13) On the “My Profile” screen, click Update Products and open the “Product” screen.
Select all checkboxes that apply and click SAVE EDITS.
Click “Update Products”
Select all that apply
Click “SAVE EDITS”
28
(14) Confirm the following screen which shows that your profile is updated.
“Role(s)” and “Products I'm Interested in” that you provided are displayed
29
(15) Open the “My Brocade Modules” as below. (It is on a right edge of the screen). Select
Licensing checkbox in Generally Available Modules column, and click SAVE EDITS.
Click this arrow, if a content of “My Brocade Modules” is not displayed.
Select “Licensing” checkbox
After you select “Licensing” checkbox, click “SAVE EDITS”.
Review the message which shows that modules are successfully saved
30
(16) You now finish user registration and configuring your account. Click Log Out(in the
screen top right corner)to log out Web site.
Refer to a following chapter about the procedure to obtain a license key.
31
5 Log in to the Web site
This chapter describes how to log in to the Web site and where the
Web site for obtaining a license key is.
1. Customer Log in (Log in to MyBrocade)
(1) Set up the PC so that it has access to Internet. Open the Web browser and go to the
URL shown below. The Brocade Web site appears.
http://www.brocade.com
The screen on the Brocade Web site might be changed without a previous notice.
(2) On the Brocade Web site screen, click Customer Log In.
(3) On the “Brocade Connect is Now MyBrocade” screen, click Log in to MyBrocade.
Click “Log in to MyBrocade”
Click “Customer Log In”
Caution
32
(4) On the “Log in” screen, enter your USER ID and PASSWORD and click login.
Enter your USER ID and PASSWORD,and click “login”.
33
2. Enter the Software Portal
(1) If you log in the Brocade Web site, click Enter the Software Portal > on the “Licensing
Tools” screen.
(Omitted)
If “Enter the Software Portal >“ is not displayed, your profile might not have been updated in
your account in the procedure of chapter 4 User Registration. Review your registered profile in
your account. If you click “my account” menu in the screen top, you can go to a registration
screen of your profile. When you click “my home” menu, you return to an original screen.
Click “Enter the Software Portal >”
If you click “my home”, you return to an original screen
If you click “my account”, you go to a registration screen
Caution
34
(2) Click License Management > Brocade FOS > License Generation with Transaction
Keys.
Click “License Generation with Transaction Keys”
35
3. Obtain the License Key
(1) On the “Brocade FOS License Generation” screen, fill the fields listed below and click
Add.
Customer Information
Customer email ID: Enter the recipient where a confirmation e-mail is to be sent
Site Name : Enter your site name
Technical Contact: Enter TEL
Company Name: Enter your company name
City: Enter your city name
State/Province: Enter your state/province name
Zip/Postal Code: Enter your zip/postal code
Country: Select your country
Phone: Enter your phone number
Unit Information:
Unique ID Type Select LID.
Unit’s Unique ID
Enter the WWN of the Fibre Channel Switch
where a license is to be installed.
This is the WWN obtained in Section 3 "Confirm the Fibre Channel Switch's WWN" of Chapter 3.
Transaction Key
Enter your Transaction Key for the license.
This is the Transaction Key provided in the Software License Package which you purchased.
36
Fill the fields and click “Add”.
37
(2) When switch and license information you provided is displayed in the bottom of Unit
Information, review the displayed information. If there is no error, select the “I have
read and accept the Brocade End User License Agreement” checkbox, and click
Generate.
(3) On the screen such as below, the License Key is displayed. Write down the value of the
"License Key" column in the blank area. You will receive the e-mail which is written the
License Key you obtained.
(4) Click Log Out in the Web site screen top and log out.
10:00:xx:xx:xx:xx:xx:xx xxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx
xxxxxxxxx
v
xxxxxxxxxxxxxxxxxxxxx
xxxxxxx
TEL
xxxxxxx
xxxxxxx
xxxxxxx
xxxxxxx
xxxxxxx
xxxxxxxxxxxxxxxxxxxx10:00:xx:xx:xx:xx:xx:xxxxxxxxxxxxxx
xxxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxxxxxxx
If there is no error, select the “I have read and accept the Brocade End User License Agreement” checkbox, and click “Generate”.
Write down the value of the
"License Key" column
Review
38
6 Install the License
This chapter describes how to install the Fabric Watch license in the
8Gbps Embedded Fibre Channel Switch module.
1. Check Compute Blade Status Chapter 3 shows the requirements to be met to perform the procedure in this chapter. If the configuration, the status of the Compute Blade and Fibre Channel Switches meet the requirements, go to Section 2 "Install the License."
Otherwise, follow the steps shown in Section 1 "Check System Status" of Chapter 3 and activate the Fibre Channel Switch.
2. Install the License (1) Use a LAN cable to connect the PC and the Management module or 8Gbps Embedded
Fibre Channel Switch module (for connection to the 8Gbps Embedded Fibre Channel Switch module). (For more information on the connection, see Section 3 " Confirm the Fibre Channel Switch's WWN" of Chapter 3.)
(2) Check that the Fibre Channel Switch is up and running. Telnet to the switch and login as an administrator (admin) with the appropriate user ID and password.
Fabric OS (SW5460)
switch login: xxxxx ← Enter User ID of administrator (admin). Password: xxxxx ← Enter Password.
switch:admin>
39
(3) Use the licenseadd command to install a license key. The syntax for the licenseadd command is as follows:
(4) Enter the licenseshow command to check that the Fabric Watch license is installed.
Obtain the licenseshow command log containing the Fibre Channel Switch configuration information, and save it in a safe device such as a floppy disk.
(5) Use the exit command to terminate the telnet session.
3. Stick the Nameplate Stick the supplied license nameplate on the lever of the Fibre Channel Switch in which the license is installed.
switch:admin> licenseadd Rdb9cbcSQQUecAdS ← Enter licenseadd command. adding license-key [Rdb9cbcSQQUecAdS].
switch:admin> License Key. Enter your license key
obtained in Section 3 "License Key Acquisition." of Chapter 5
switch:admin> licenseshow ← Enter licenseshow command.
RSyRyze9QbSTzSzO:
Web license
Rdb9cbcSQQUecAdS:
Fabric Watch license
ScRSzRzbRdTdST02:
Zoning license
bbbR9zSdQzcccSAI:
Fabric license
SRd9Sddyy9XSeATi:
Performance Monitor license
switch:admin>
Indicates that the Fabric Watch
license is installed.
40
7 Download Recommended Configuration Information
To use the Fabric Watch feature, you also need to download a
configuration file (containing the recommended configuration
information) to the Fibre Channel Switch in addition to installing the
Fabric Watch license.
The download procedure in this chapter requires an FTP server to run
on the networked UNIX system. If you have no FTP server connected
to the Fibre Channel Switch, you can use the PC connected to the
Fibre Channel Switch as an FTP server by installing the standard
Windows IIS FTP server on the PC.
If you already have an FTP server connected to the Fibre Channel
Switch, you can skip Section 2 "Install the IIS FTP Server."
1. Check Compute Blade Status Chapter 3 shows the requirements to be met to perform any of the procedures in this chapter. If the configuration and status of the Compute Blade and Fibre Channel Switches meet the requirements, go to Section 2 "Install the IIS FTP Server" or Section 3 "Download Recommended Configuration Information."
Otherwise, follow the steps shown in Section 1 "Check System Status" of Chapter 3 and activate the Fibre Channel Switch.
2. Install the IIS FTP Server
(1) Click Start → Settings → Control Panel to open the "Control Panel" window.
41
(2) Double-click "Add/Remove Programs" in the "Control Panel" window to open the
"Add/Remove Programs" window.
(3) Click "Add/Remove Windows Components" in the leftmost side of the "Add/Remove
Programs" window to open the "Windows Component Wizard."
42
(4) Check "Internet Information Services (IIS)" () and then click "Details" () at the
lower-right side of the window.
(5) Confirm that "FTP (File Transfer Protocol) Server" is checked () and then click "OK"
() at the lower-right side of the window to return to the "Windows Component Wizard."
43
(6) Click "Next" at the lower-right side of the "Windows Component Wizard."
(7) The "Internet Information Services (IIS)" starts to be installed.
44
(8) If files are required, the following window will appear. (The OS CD and Service Pack CD
may be required.)
(9) The Windows Component Wizard completion window appears. Click "Finish" at the
lower-right of the window.
This completes the installation of the IIS FTP server.
Subsequently, set up the IIS FTP server
45
(10) Double-click "Users and Passwords" in the "Control Panel" window to open the "Users
and Passwords" window.
Note: If the user was registered according to this procedure, the
following user name, password, and root directory are used for the
FTP server:
User name: upload
Password: password
Directory: C:¥inetpub¥ftproot
46
(11) Click "Add" in the "Users and Passwords" window to add a new FTP access user.
(12) Enter "upload" as the user name () and then click "Next" ().
47
(13) Enter "password" (lowercase letters only) in two password fields () and then click
"Next" ().
(14) Click "Finish."
48
(15) Confirm that FTP user "upload" has been added () and then click "OK" ().
This completes the creation of the FTP access user.
49
(16) Double-click "Administrative Tools" in the "Control Panel" window to open the
"Administrative Tools" window. Confirm that FTP user "upload" has been added and then
click "OK."
(17) Double-click "Internet Services Manager" in the "Administrative Tools" window to open
the "Internet Information Services" window.
50
(18) Expand the tree in the left-hand window (click +).
(19) Right-click "Default FTP Site" and then click "Properties."
51
(20) Click the "Security Accounts" tab in the "Default FTP Site Properties" window.
(21) Uncheck "Allow Anonymous Connections."
52
(22) The confirmation dialog box appears. Click "Yes."
(FTP encodes no password, regardless of whether anonymous connection is set.)
(23) Click "Apply" () at the bottom of the "Default FTP Site Properties" window.
Next, click the "Home Directory" tab ().
53
(24) Check "Write" (), click "Apply" () at the bottom of the "Default FTP Site Properties"
window, and then click "OK" ().
(25) To confirm whether the created folders can be referenced from FTP, connect to the FTP
site () and confirm them (). After successful confirmation, end the connection ().
Microsoft Windows 2000 [Version 5.00.2195]
(C) Copyright 1985-2000 Microsoft Corp.
C:\Documents and Settings\Administrator>ftp 10.77.77.236 Connected to 10.77.77.236. 220 F310DA3-146 Microsoft FTP Service (Version 5.0). User (10.77.77.236:(none)): upload ←User name 331 Password required for upload. Password: ←Password 230 User upload logged in. ftp> dir 200 PORT command successful.
150 Opening ASCII mode data connection for /bin/ls.
08-04-06 03:08PM <DIR> config
08-04-06 03:08PM <DIR> firm
226 Transfer complete.
ftp: 92 bytes received in 0.00Seconds 92000.00Kbytes/sec.
ftp> bye
221
C:\Documents and Settings\ Administrator >
①:Connect to the FTP site with the “ftp ip” address. ②:Use the dir command to confirm the created folders. ③:Use the bye command to terminate connection.
①
②
③
54
3. Download Recommended Configuration Information
(1) Use Windows Explorer to locate the Fabric Watch configuration file and copy the file into
the "C:¥inetpub¥ftproot" on the PC connected to the switch.
(Copy the file, not the folder.)
If you are going to use an FTP server other than IIS, copy the configuration file into an
appropriate directory for FTP transfer.
Use the following configuration file contained in the supplied CD or in the embedded
USB(Configuration file can be contained in embedded USB only if system is CB500):
■ CB2000
¥ FW ¥CB2000¥ FWconfig_sw5460_*.txt
■ CB500
¥ FW ¥CB500¥ FWconfig_sw5460_*.txt
(2) Use a LAN cable to connect the PC and the Management module or 8Gbps Embedded
Fibre Channel Switch module (for connection to the 8Gbps Embedded Fibre Channel
Switch module).
(For more information on the connection, see Section 3 " Confirm the Fibre Channel
Switch's WWN" of Chapter 3.)
(3) Check that the Fibre Channel Switch is up and running. Telnet to the switch and login as
an administrator (admin) with the appropriate user ID and password.
※ To telnet, use the same network address for the Fibre Channel Switch and PC, when you use a LAN cable to connect the PC and the Fibre Channel Switch module.
(4) Enter the switchdisable command to turn the Fibre Channel Switch offline.
switch:admin>switchdisable ← Enter switchdisable command
Fabric OS (SW5460)
switch login: xxxxx ← Enter User ID of administrator (admin). Password: xxxxx ← Enter Password.
switch:admin>
55
(5) Enter the configdownload command to download the recommended Fabric Watch
configuration information.
(6) Enter the switcheable command to turn the Fibre Channel Switch online.
(7) Enter the fwclassinit command to activate the Fabric Switch.
(8) Enter the reboot command to reboot the Fibre Channel Switch.
(9) The telnet session is terminated.
switch:admin> configdownload ← Enter switchdisable command.
Protocol (scp or ftp) [ftp] : ftp ← Enter ftp. Server Name or IP Address [host] : 10.0.1.10 ← Enter the IP address of ftp. User Name [user] : upload ← Enter upload. File Name [config.txt] : FWconfig_sw5460_r*.txt ← Enter the name of
the configuration file.. Section (all|chassis [all]):all ← Enter all. Password : password ← Enter password.
*** CAUTION ***
This command is used to download a backed-up configuration
for a specific switch. If using a file from a different
switch, this file's configuration settings will override
any current switch settings. Downloading a configuration
file, which was uploaded from a different type of switch,
may cause this switch to fail. A switch reboot might be
required for some parameter changes to take effect.
configDownload operation may take several minutes
to complete for large files.
Do you want to continue (yes, y, no, n): [no]y ← Type “y.”
<途中省略>
configDownload complete: All config parameters are downloaded
switch:admin>
switch:admin>switchenable ← Enter switchenable command.
switch:admin>fwclassinit ← Enter fwclassinit command.
fwClassInit: Fabric Watch is updating...
fwClassInit: Fabric Watch has been updated.
switch:admin>
switch:admin>reboot ← Enter reboot command.
56
8 Completion Steps
Now that your license is installed, you are ready to perform the
completion steps, depending on the action that you have taken during
preconfirmation described in Chapter 3."
If you have switched to the alternate path to
the Fiber Channel Switch where the license is
not to be installed
If necessary, you should switch back to the
path to Fibre Channel Switch where the
license is installed.
This completes the process.
If you have stopped only the servers
connected to fibre channels
No completion step is required.
You have already completed the process.
57
9 Troubleshooting
This chapter lists some common troubles which you may encounter while performing a
task described in this manual.
If you take an action described in the User Action column and the trouble persists,
please contact your sales representative where you purchased the package or call your
service engineer.
No Symptom User Action
1 A wrong WWN was used to obtain a license key. Contact your dealer where you purchased the license package.
2 An error message appears on a browser screen used to obtain a license key.
Check the error message to see whether an incorrect value is entered (especially for a transaction key).
3 The Error LED on a Fibre Channel Switch turns on.
Refer to the section concerning troubleshooting in manuals in Compute Blade Fibre Channel Switch Accessory CD to fix the error. If the error persists, call your service engineer.
58
( This page is blank. )
MK-99COM080-00
Hitachi Data Systems
Corporate Headquarters
2845 Lafayette Street Santa Clara, California 95050-2639
U.S.A.
www.hds.com
Regional Contact Information
Americas
+1 408 970 1000 [email protected]
Europe, Middle East, and Africa
+44 (0) 1753 618000
Asia Pacific
+852 3189 7900