How do I configure my newly bought D-Link DSL-2730u Wireless N 150 ADSL2+ 4-Port Router(cum modem)_ • Airtel Broadband.pdf

8/10/2019 How do I configure my newly bought D-Link DSL-2730u Wireless N 150 ADSL2+ 4-Port Router(cum modem)_ Air

1/7

Tweet 0

Recently, I bought a D-Link DSL-2730u Wireless N 150 ADSL2+ 4-Port

Router(i.e also modem) to connect to my Airtel broadband. I've given up after

repeated failures to connect to the Internet.When I ran the diagnostics

through 192.168.1.1 of the modem, the process is failing in the step when its

connecting to the ISP. I've validated the ISP's username and password butstill It gets failed there.Though, I am getting a valid DSL signal, but after that

its throwing the error 651.I'm using Windows 7. And searched the net for all

possible solutions for this error. Tried each one of it, nothing's working.Am I

configuring the Modem right? Please assist as to what settings I must

put.Thanks in advance.

^ I don't know which fields are required for D-Link but I recently got a

Linksys WAG120N and for setting up I changed the following -Encapsulation

- RFC 2516 PPPoEMultiplexing - LLCQoS - UBRVPI - 1VCI - 32DSL

Modulation - Multimode (if it does not work fall back to G.Dmt)Username

and Password -DNS Server - Use Airtel / OpenDNS / Google DNS / DNS

do I configure my newly bought D-Link DSL-2730u Wireless N 1... https://broadbandforum.co/threads/how-do-i-configure-my-newly

10/18/2014


2/7

AdvantageHope it helps

Follow these steps in this order for DLINK 2730 modem, for setting up both

as a LAN router and Wifi Access Point. Connect the LAN cable to LAN1 porton router and login to router ip (192.168.1.1) for doing these setup. Login with

admin/admin as userid/password.1) Advanced Setup-> Layer2, Add atm0

with default settings2) WAN Service -> Add with Bridge type selected, keep

others default3) Wireless ->Enable Wireless, and give your own SSID, keep

others default4) Wireless-> Security-> Give Network Authentication as

WPA-Personal, and passprase will be your own password to connect to WiFi5)

Interface Grouping -> Give a group name as WAN, and select WL0, LAN2,

LAN3, LAN4 from right to left, Apply/Save. Now there should be 2 groups one

Default with LAN1 and other with new Group Name6) LAN -> In the right top

dropdown select WAN group and disable DHCP, Apply/Save7)Management->Settings->Backup your settings8) Management ->

RebootConnect the output from Tikona to LAN2 port on the router, connect

your laptop to Wifi on the router using the SSID/passphrase. This should

work, else shutdown router for 10 seconds, disable your wireless network and

log-off/on again, enable wireless network and try connecting again.After this

the ethernet wire coming from Tikona should be connected to LAN2 port, and

you can use wifi. Note that LAN1 port is used to connect to the router only

(192.168.1.1) after this setup.RegardsShashi

Perfectly worked. Thanks a lot Shashi. ositive:


10/18/2014


3/7

I followed these settings on my dsl 2730u. I 'm trying to connect to my phone

and laptop to the wifi network. I connected my laptop first and then tried to

connect to my phone. I'm getting redirected to my Internet service providerslogin page on my phone and once I login on my phone, I'm not able to access

internet on my laptop. Is there a way to resolve this?

Check if there is an option Clone PC MAC address under Advance

Setup->WAN->Edit. If it is there try cloning the PC mac address so that the

ISP sees only one device connected. Its there on my 2750u not sure about the

2730u. May be this helps in this issue.


10/18/2014


4/7

I tried follwing your instructions for my similar in2net connection which uses

tikona like setup. In the interface grouping section on clicking save my router

hangs, any ways even without any settings only one of the devices(android

phone with pppoe) or my laptop connects . I am unable to simultaneously use

both my device using this same router. I connect the ppoe lan cable to the lan

port and a ppoe connection helps me connect to the intenet both on my lappyand the android device.

Hence how to get multiple access over wifi?

Thanks for your response.

There is no such option on my 2730U

Probably MAC cloning will only solve it.

Click to expand...


10/18/2014


5/7

Only 2 devices are allowed at a time in Tikona. I am able to connect my laptop

and android at the same time. We need to login at tikona site from bothdevices to use internet. You did not mention the error. What error are you

getting?


10/18/2014


6/7


10/18/2014


7/7


Documents

How do I configure my newly bought D-Link DSL-2730u Wireless N 150 ADSL2+ 4-Port Router(cum modem)_ • Airtel Broadband.pdf